Korea Data Systems Co KD-1731 User Manual 69742

Download:
Mirror Download [FCC.gov]
Document ID	69742
Application ID	tnXhrTehQ8JB8X8lmxsKsg==
Document Description	8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	23.11kB (288849 bits)
Date Submitted	1999-11-15 00:00:00
Date Available	1998-09-18 00:00:00
Creation Date	2001-05-14 21:23:56
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-05-14 21:24:07
Document Title	69742.pdf
Document Author:	VicodinES /CB /TNN

APPENDIX C:_
USER’S MANUA_L_ _
Dncnm mmmmmmmmmmm
Operation & Installation Guide
MODEL NO. : KD-1731
17" Multi-Scan Color Monitor
(15.8”diag. Viewing area)
FCC Compliance Statement
Safety Instructions
Introduction
Product Package
Setup
Contro‘s and Adjustments
Tnming Guide
Specmcations
EM
—'OU1(JN—‘
FCC Compliance Statement
Note:
This equipment has been tested and found to comply with the limits
fora Class B digital deVice, pursuant to Part 15 of FCC Rules. These
limits are deSigned to provide reasonable protection against harmful
interference in a residential installation, This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the lollowmg measures
» Reorient or relocate the receiVing antenna.
- Increase the separation between the equipment and receiver.
4 Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
- Consult the dealer or an experienced radio/television
technician for help.
Notice 1:
The changes or modifications not expressly approved by the party
responsible for compliance could veid the user's authority to operate
the equipment.
Notice 2:
Shielded interface cables, it any, must be used in order to comply with
the emisSion limits.
DOC CLASS 5 NOTICE
This digital apparatus does not exceed Class B limits for radio noise
emission for a digital apparatus as set out in the Radio lnterterence
Regulations of the Canadian Department of Communications.
Safety Instructions
lO
Read these instructions Save these instructions for later use.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet belore cleaning. Do not
use liquid cleaners or aerosol cleaners Use a damp cloth for
cleaning
Do not use this product near water.
Do not place this product on an unstable cart, stand, or table. The
product may fall, causing serious damage to the product
Slots and openings in the cabinet and the back or bottom are
provrded for ventilationno ensure reliable operation of the product
and to protect it from overheating, these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other srrnilar surface.
This product should never be placed near or over a radiator or heat
register, or in a built in installation unless proper ventilation is
provided.
This product should be operated from the type of power indicated
on the marking label. If you are not sure of the type of power
available consult your dealer or local power company.
Do not allow anything to rest on the power cord. Do not locate
this product where persons will walk on the cord
If an extension cord is used with this product, make sure that the
total of the ampere ratings on the products plugged into the
extensron cord does not exceed the extension cord ampere rating.
Also make sure that the total of all products plugged into the wall
outlet does not exceed 15 amperes,
Never push objects of any kind into this product through cabinet
slots as they may touch dangerous voltage points or short out
parts that could result in a risk of fire or electric shock Never
spill liquid of any kind on the product.
Ill
“
Safety Instructions
11 Do not attempt to service this product yourself, as opening or
removrng covers may expose you to dangerous voltage points or
other risks Refer all sen/icing to service personnel
12 Unplug this product from the wall outlet and refer servicing to
qualified servrce personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
a ll liquid has been spilled into the product.
c. lf the product has been exposed to rain or water.
[1
. if the product does not operate normally when the operating
instructions are followed Adjust only those controls that are
covered by the operating instructions since improper adjust-
ment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the
product to normal operation
e, lithe product has been dropped or the cabinet has been
damaged,
13. Use only the proper type of power supply cord set (provided in
your manual accessories box) for this unit. lt should be a
detachable type:UL listed/GSA certified, type SvT/SJT, rated as
10A l25V minimum, VDE approved or its equrvalent‘
14 The Socket-Outlet 15 to be installed near the equipment and is
easily accessible
This product is manufactured in accordance with quality assurance
system approved by ISO 9001 certification process,
IV
introduction
1. General information
Congratulations on selecting this high resolution multi-scan color
monitor.
This high performance display contains the latest technology of flat
screen design and microprocessor control. This monitor has been
equipped with both automatic and manual adjustments.
The automatic controls are factory preset and feature automatic
factory frequency scanning.
The manual controls feature use digital adjustments to personalize
the display in various applications.
The ergonomic characteristics of the antiglare flat screen, high
refresh rates, and tilt swivel base allow comfortable usage when
operating for a long period of time in high resolutions.
This operating manual describes the functions and features in more
detail so that you may obtain the maximum performance of your
monitor
2. Features
0 17“ antiglare, flat screen, high-contrast picture tube.
0 0.28mm dot Ditch
' IBM compatible
~ Multi—scan 1 horizontal frequencies 30»70l Development, Production and Servicing for
ER? Monitors. Proof has been furnished that the
DtleOOOM requirements according to lSO 9001 are
”Whimmw’ fulfilled.
“
Product Package
Derermine the most conveniem location for your moniror.
Make sure that you have enough room to install cables and
connect the monitor to the syslem and power supply.
Open the shipping canon and check the contents of the package
The package should include the followmg items”
* i7‘ Color Monitor
. AC Power Cord
- Owner's Manual
Note' if any irem(s) are missing or damaged comacr your dealer
immediately.
2, Remove the monitor from its shipping canonisee figure 1).
Save the carton and packaging materials in case you need to
relocate the moniror.
Setup
Setting up your monitor is easy. All you have to do IS make a
few simple connections and adjustments. The procedure IS as
follows:
1. Start up
Switch the power off to both your monitor and computer. The
location of the power swrtch is on the lower right hand corner
of the monitor.
2. Power cable Connection.
Connect the female end of the power cable to the power
input on the back of the monitor. Next. plug the male cable to
the wall outlet for power.
To power input of monitor
Gib
fl . r \l
E o
G B
To AC outlet
firm-ff
To PC inlet
FigureZ
3. Signal cable connection
Connect the 15 pin Signal cable to the your computer.
Lock both screws to ensure grounding.
PIN NO, DESCRIPTION PIN NO DESCRIPTION
1 Video red 9 N. C
2. Video green 10 Ground
3. Video blue 11. Ground
4 N C 12 SDA
5 DDC Return 13 Her-Sync
D we 15pm connector 6 Video red ground 1A Ver~Svnc
FIG” 3 7. Video green ground ‘l5 SCI.
8. Video Due ground
Setup
44 Power on
Switch on the power to both your monitor and computer.
5. Adjusting the Picture
Adjust the controls, if necessary, to get the best picture.
A description ol the functions of the controls may be found in
the next section
6. Adjusting the Tilt-Swivel Base
The tilt-swivel base can be adjusted for your maximum
Viewing comfort, it can be adjusted through angles of 90'
horizontally and 15" vertically.
go.
16'
N ote:
Due to the sensrtlwty of this monitor to earth's magnetic
field, you may experience minor irregularities in the display it
you swivel the monitor through more than 90" while the
monitor is ON, If such behavior occurs. please turn the monitor
OFF and ON again. The display should return to normal,
I Setup ofthe Video Circuitry
To use the full potential of this product it IS necessary to
first set the Video circuitry of the computer according to the
maximum capabilities of this monitor.
This can be expressed in any of the following ways:
-1280X‘l024 GOHZ
—1024>< 768 85HZ
Controls and Adjustments
There are a lew switches that are located on your monitor
The power indicator and adjustable controls allows the user to
maximize the display for indrvidual preferences.
The description of these functions are as follows '
Front Panel Controls
DlGlTAL CONTROL PANEL POWER ON/OFF SlNlTCH
POWER lNDICATOR
1. Power ON/OFF Switch
Press this button to turn the power ON or OFF. There Will be
a short delay before the display appears.
2, Power Indicator
This power indicator illuminates when the power is swrtched ON
and the power cord is properly attached.
Green/Amber Green/Amber
Blink 1.0 sec Blink 2.0 sec
MODE ON STAND BY SUSPEND f; OFF
Power Indicator Green Amber
Controls and Adjustments
4. Digital Control Panel
The digrtal control panel rs located at the bottom of your color monrtor,
If you are not satrsfred wrth the factory settings, use these controls to
program those you prefer in each resolutron
Thenr these adiUSted settings are kept in memory even rt you change
resolution or turn off the monitor,
066)
EXlT/
DEGAUSS DOWN UP ENTER
KEY FUNCTION
1t ENTER
Call Mam Menu and sub - menu
Call the SubrMenu ‘rn state that the OSD rs drsplayed
2. UP/DOWN
Vary the value for each functrons.
3, EXIT/DEGAUSS
Drsable the OSD and degaussing
key “r ln state of No 050 Main Menu Sub Menu
Enter Call Marn Menu Call SubMenu Swrtched 9am menu
Up Contrast Control Enable Before item Optimrze the screen
Down Contrast Control Enable Next rtern Optmrze the screen
Exit 1 Degaussing Exrr Return to the main menu
Controls and Adiustments
ON SCREEN CONTROL ON SCREEN CONTROL
CONTRAST
es/e : SELECT
0 : ENTER
BEIIIJIDEIEJE]
lillfilESIEEE
102A x 768 @75Hz
Press 0 Tb Exit
Press 8 To Exit
FM wflKHz 51175041
Menu Descriptions
CONTRAST 0
Adjustments the black level of the display
BRIGHTNESS {©1-
Adiustments the luminosity level of the display.
H - POSITIONIHORIZONTAL POSITION) ID
Select thts control then use the + and 4 buttons to center the image horizontally on
the display screen
H - SIZE(HORIZONTAL SIZE) 5
Select (hlS control, then use the + and - buttons to expand or decrease
the image width to horizontally till the display screen,
V»FOSIT10N(VERTICAL POSITION) 8
Select this control, then use the + and - buttons to center the image
vertically on the display screen.
V»SIZE(VERTICAL SIZEI ED
Select this control, then use the + and - buttons to expand or decrease
the image height to vertically fill the disply screen
SIDE-PIN(PINCUSHIONI Ell .
Select this control, then use the + and - buttons to stralghten the Sides
of the mags; by pulling them in opposmg directions
Controls and Adiustments
PIN BALANCE EU
Select this control, then use the + and - buttons to straighten the sides
of the image by pulling them in the corresponding direction
TRAPEZOID
Select this control, then use + and - buttons to even the widths of the
top and bottom of the display (pulling the sides in opposing directions)
PARALLELOGRAM El
Select this control. then use the + and - buttons to center the top and
bottom of the display (pulling the sides in the corresponding direction)
ROTATION
Select this control, then use the + and — buttons to rotate the image
until sides of the image are parallel to the edge of the bezel.
COLOR CONTROUTEMPERATURE)
Select this control, then use the + and - buttons to scroll to the desrred
temperature. Use the 0 button to select either the 9300” K, 6500“ K,
5500“ K or user for a custom RGB setting
COLOR CONTROL
WQGDO K 5500 K
6500 K USER
.—:i 85V»
G _:l 557»
E._:I 85%
9/9: SELECT
O: ENTER
9: RETURN
—
Controls and Adjustments
R - GAINtRED) El
Select “User" then use the 9 button to scroll up and down the RGB
meun to RtFledl Use the + and - buttons to adjust the red level of the
display
G»GAIN(GREEN) El
Select "User" then use the 0 button to scroll up and down the HGE
menu to GlGreenl, Use the+ and ~ buttons to adyust the green level of
the display
B-GAIN(BLUE)
Select "User" then use the 9 button to scroll up and down the RGB
menu to B(Bluel Use the+ and - buttons to adjust the blue level of the
display
030 POSITlON
Select this control. then use the 0 button to select m which direction
to move the OSD menu. Use the + and - buttons to move the OSD
menu.
RECALL O
Resets the display settings to the original factory preset values. Press
and hold down the 0 button Lll’l!l| the progress bar disappears
SIGNAL (“ABLE
POWER CORD
Timing Guide
The i7' color monitor is an Digital multi-scan manner. It operates
at horizontal frequencies of anywhere between 30 KHz and 70 KHZ.
Because of its microprocessor-based design, it offers
auto-synchronlzation and auto—sizing capabilities, At the preset
status, this monitor offers H pie-programmed settings for more
common graphics standards. They are listed in the table below
Preset Resolution Hawaii" H Prefix-193W V Polarity Interlaced
M1 640x480/VESA 31.5 50 ~/- N
M2 720x400/VGA 31.5 70 -/ + N
M3 640X480/VESA 37.5 75 -/- N
M4 540x480/VESA 43.3 85 _/, N
M5 BDOXGOO/VESA 469 75 +/+ N
M6 BOOXSOO/VESA 537 85 +/+ N
M7 $2X624/MAC 49.7 75 -/> N
M8 1024x768/VESA 60.0 75 + / + N
M9 7024X7WVESA 58 7 85 + / + N
M10 liSZXBfid/VESA 675 75 +/+ N
M11 lZanlOZd/VESA 640 so +/+ l N 3
~ In Eddltlofl to u lacmry modes, there are 5 addmonai user modes
Il morE man 6 modes are mputten. «t will be cverrided in accordance w-m Savlflg
order of addltlonai modes.
10
Specifications
Picture tube 17' diagonal, 0.28mm dot pltCh, 90
degree deflection, nonglare etched
screen, tinted glass, medium-short
persistence phosphor.
Resolution 1280 x1024 addressable
1024 X 768 physical
Band width 100M H2
Video input Analog, posrtrve going
srgnaltOJV op)
Horizontal input TTL, positive or negative
going pulsel2.4~5v p-p)
Vertical input TTLt positive or negative
going pulselz 4~5V p-p)
Scan frequency Horizontal: 30~70KHz
Vertical: 50~150Hz
Standard display area 300mmlH) x 225mm(V)/
11 8'(H) XBB'lV)
Display color Unlimited
Power input 100~240V AC‘ SO/SOHZ
Fuse rating 250V, S 3,0AlUL, CSA, TUV) or T3.15A(TUVJ
Power consumption On . Less than 100W
Stand by ' Less than 15W
Suspend : Less than 15W
Off: Less than SW
Operating 0 To 40 Degree C.
temperature
Dimensions 411mmlW)x 424mm(H)
x 440mmlDl/
16.2”(Wl x 16 BB'lHi x 17 32'lDl
Weight 19.7Kglnet)/43143 lbs
11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:05:14 21:23:56
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : VicodinES /CB /TNN
Title                           : 69742.pdf
Modify Date                     : 2001:05:14 21:24:07-04:00
Page Count                      : 17

EXIF Metadata provided by EXIF.tools