Kyocera IUD19AB iBurst User Terminal User Manual 1 of 2
Kyocera Corporation iBurst User Terminal 1 of 2
Kyocera >
Contents
- 1. User Manual 1 of 2
- 2. User Manual 2 of 2
User Manual 1 of 2
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 706029 |
| Application ID | nCQiKF9xwT40hwJlYwYRSw== |
| Document Description | User Manual 1 of 2 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 182.45kB (2280617 bits) |
| Date Submitted | 2006-09-19 00:00:00 |
| Date Available | 2006-09-19 00:00:00 |
| Creation Date | 2006-08-21 20:12:24 |
| Producing Software | AFPL Ghostscript 8.13 |
| Document Lastmod | 2006-08-21 20:18:31 |
| Document Title | Microsoft Word - Q38T-EE-001_UTdUsersManualR101 for FCC.doc |
| Document Creator | PrimoPDF http://www.primopdf.com |
| Document Author: | yamamoto |
iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Approved Checked Designed Koyama Yamamoto Hirao Reference: Revision: Date: Kyocera Corporation -1- Q38T-EE-001 1.01 June.08.2006 Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Revision Record Revision 1.00 1.01 Author Hirao Miyasaka Kyocera Corporation Date May.10.2006 June.08.2006 Detail First Release Correct some writings -2- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual CONTENTS Safety Precautions on iBurst Terminal................................ Terminal ................................................................ .......................................................................... .......................................... 4 Chapter 1 Introduction ................................................................ ................................................................................................ .................................................................. .................................. 8 Components List ................................................................ ................................................................................................ ................................................................................................ ................................................................................ ................................................ 9 Pictures of Accessories ................................................................ ................................................................................................ ................................................................................................ ....................................................................... ....................................... 9 Outlook of iBurst Terminal ................................................................ ................................................................................................ .............................................................................................. .............................................................. 10 Indicators ................................................................ ................................................................................................ ................................................................................................ .......................................................................................... ..........................................................11 .......................... 11 Requirements on your PC ................................................................ ................................................................................................ ................................................................................................ ................................................................ 12 Outlook to use the iBurst Terminal................................ Terminal ................................................................ ................................................................................................ .................................................................................. .................................................. 12 Chapter 2 Setup Procedure ................................................................ .......................................................................................... .......................................................... 13 iBurst Software Installation .............................................................................................................. 14 Installation for Windows XP ................................................................ ................................................................................................ ............................................................................................ ............................................................ 14 Installation for Windows 2000 ................................................................ ................................................................................................ ......................................................................................... ......................................................... 17 Installation for Windows Me ................................................................ ................................................................................................ ............................................................................................ ............................................................ 20 Installation for Windows 98SE................................ 98SE ................................................................ ................................................................................................ ......................................................................................... ......................................................... 39 Installation for Mac OS X................................ X................................................................ ................................................................................................ ................................................................................................ ................................................................. ................................. 59 Connection Establishment ................................................................................................................. 63 Connection Establishment for Windows XP ................................................................ ................................................................................................ ..................................................................... ..................................... 63 Connection Establishment for Windows 2000/Me/98SE ................................................................ ................................................................................... ................................................... 68 Connection Establishment for Mac OS X ................................................................ ................................................................................................ ......................................................................... ......................................... 70 Chapter 3 Utility Software ................................................................ .......................................................................................... .......................................................... 74 Using Utility Software........................................................................................................................ 75 Software Using Utility Software for Windows................................ Windows ................................................................ ................................................................................................ ................................................................................. ................................................. 75 Using Utility Software for Mac OS X ................................................................ ................................................................................................ ............................................................................... ............................................... 81 Status Indication over Ethernet ........................................................................................................ 88 Chapter 4 MTU Optimizer Software & Network Property .......................................... .......................................... 93 MTU Optimizer Software & Network Property................................................................................ 94 Property Chapter 5 Uninstallation Uninstallation ................................................................ ............................................................................................. ............................................................. 97 iBusrt Software Uninstallation.......................................................................................................... 98 Uninstallation Uninstallation for Windows XP/2000 ................................................................ ................................................................................................ ............................................................................... ............................................... 98 Uninstallation for Windows Me/98SE ................................................................ ................................................................................................ ............................................................................. .............................................101 ............. 101 Uninstallation for Mac OS X ................................................................ ................................................................................................ ........................................................................................... ...........................................................108 ........................... 108 Chapter 6 Trouble shooting................................ shooting................................................................ ......................................................................................... .........................................................110 .........................110 Windows..............................................................................................................................................111 Windows USB connection with Windows Me/98SE ................................................................ ................................................................................................ ........................................................................ ........................................ 111 Illegal hanghang-up when install iBurst Terminal. ................................................................ ................................................................................................ ................................................................ 114 Illegal hanghang-up when set up dialer................................ dialer ................................................................ ................................................................................................ .................................................................................. .................................................. 116 PC hanghang-up when eject iBurst Terminal from Win98 USB port. ................................................................ ..................................................................... ..................................... 118 Mac ..................................................................................................................................................... 119 Data rate ................................................................ ................................................................................................ ................................................................................................ ......................................................................................... ......................................................... 119 Chapter 7 Information ................................................................ ............................................................................................... ............................................................... 120 FCC Compliance Statement............................................................................................................. 121 Statement FCC RF Radiation Exposure Statement ......................................................................................... 121 Kyocera Corporation -3- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Safety Precautions on iBurst Terminal • Things you must know • • • When using the product, use it correctly according to the safety precautions. The product uses particular radio frequency band tuned for the network operator. The safety precautions, hardware, software, and the design of the product may be changed in the future without any announcement to the customers. • About use restriction • • The product is designed as an OA apparatus for home use. Please use it neither in the medical apparatus directly to affect a human life, nor the system of which very high reliability is required. Do not use the product in the zone where the wireless machines are forbidden, such as an airplane and a hospital. An electric device and medical apparatus are affected and it becomes the cause of the accident. • About Qualification • • • • • • • • Our company does not take any responsibility about the damage produced by use under the conditions such as natural disasters, earthquake, flood, fires, misuse by intent or carelessness or other than the responsibility of our company. Our company does not take any responsibility about the damage produced by external factor, failure, malfunction, and fault of product, such as loss of enterprise profits, enterprise discontinuation, change and disappearance of the contents of memory etc. Our company takes no responsibility about the damage produced by not keeping the written contents of an owner's manual. Our company takes no responsibility about the damage produced from incorrect operation in combination with the connection apparatus and software in which our company is not participating etc. iBurst ™ is a registered trademark of ArrayComm, Inc. Mac OS X is a registered trademark of Apple Computer, Inc. Windows is a registered trademark of Microsoft Corporation. In addition, the name of the software carried in this document and peripheral equipment is each company’s trademark, or a registered trademark. Kyocera Corporation -4- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual • For your safety -------- Danger -------( If used improperly, may cause death or serious injury. ) • • • • • • • • • • • • Do not use with an abnormal condition, such as with emission of smoke or odor. It may cause fire or electric shock. Do not insert metal or flammable materials into the product interior through the air vents. Pull out power plug from the outlet in case that foreign material into the product interior. It may cause fire or electric shock. Do not disassemble or remodel the product. It may cause fire or electrical shock. Do not use or place the product at places with high humidity such as in the bath room or near the humidifier. It may cause fire or electric shock. And do not touch the product with wet hands. Do not use the product with power supply other than AC100 to 240V. It may cause fire or electric shock. Do not plug too many leads into a single socket with extensions such as table taps, divided outlets, and divided sockets. It may cause fire or electric shock. Moreover, make sure that the total current does not exceed the capacity of the power supply. Otherwise, may cause fire or electrical shock. Do not damage, break, modify, bend, pull, twist, or bundle the AC cord. In addition, if a heavy material is placed onto the cord or it is heated, the cord may break and cause fire or electric shock. Securely insert the plug into the outlet. If a metal object edges the teeth of the plug, it may cause fire or electric shock. When pulling out the plug from the outlet, be sure to hold onto its head. Pulling the cord can damage itself. When you change the installation place of the product, pull out the plug from the outlet and confirm that PC is completely separated from it. Otherwise, the cord may be damaged and cause electric shock or fire. Before inserting the plug into the outlet, check that there is no dust on its edge and head. As dusts can easily enter between the plug and the outlet, they may cause fire or electric shock. Pull out the plug from the outlet, at least once in a half year or a year, and clean/maintenance. Use the AC/DC adapter enclosed with the product. Usage of other AC/DC adapters may cause fire or electric shock. Do not place things or put cloth on the top of the plug. It may heat and break the plastic and/or the rubber, causing fire or electric shock. Kyocera Corporation -5- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual ------- Warning -------( If used improperly, may cause disability or physical damage. ) • • • • • • • • • • • • • Do not give a shock strong against the product, such as dropping and throwing. It becomes the cause of failure. Moreover, do not ride on the product. It may become the cause of an injury. Do not put the product under direct sunshine or near equipment with high temperature such as a stove and a heater. It may raise the temperature of the interior and cause fire. Do not put the product at places with an extreme fluctuation of temperature, such as near the air conditioner or a heater. The dew condensation may occur in the interior and cause fire, electrical shock, and malfunction. Do not put the product at places with oil and steams such as in the kitchen. In addition, do not put it at dusty places and places where metal powder and toxic gas occur. It may cause fire or electric shock. Do not place the product on unstable places such as on an unsteady desk or slanted surfaces. In addition, do not put any object on the product. It may loose balance and tumble, or fall and cause injury. When the thunder occurs in near, do not use the product and its peripheral equipment. It may become the cause of an electric shock. If the air vents are blocked, the interior may be heated and cause malfunction. Please do not use the products in the following manners; Put on carpet or bedclothes. Cover with tablecloths. Put at places with bad ventilation, such as on a book shelf, in the drawer, or in the closet. If suspending the use for a long time, pull out the plug from the outlet. Do not use the AC cord with an extension cord. It may cause fire. For maintenance, pull out the AC plug from the outlet for safety. Do not wipe the product with benzene, thinner, or alcohol. It may cause the product to decolorize or deform. If the product be stained, put some neutral detergent on a dry cloth and wipe gently. Do not connect electricity supplied LAN cable to the product. It may cause smoke or fire. Do not touch the connector pins directly with your hands. Static electricity may affect the components. As static electricity is created from both the cloth and the human body, before putting or removing the product, release static electricity by touching a metal object such as a small cabinet. Do not use it in the intense place of vibration. It becomes the cause of failure. Kyocera Corporation -6- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual -------- Caution -------( If treated improperly, the equipment may not perform or work properly. ) • • • • • • • • Do not put the product at low temperature. The product may not function properly. Do not put the product on the top of magnetic objects and places where electromagnetic waves occur. This includes electrical appliances, AV, and OA (microwave oven, speaker, TV, radio, fluorescent light, inverter air conditioner, and electric kitchen appliances). The product will not be able to make communication properly if effected by magnetism or electronic noise. Putting the product near TV or radio may cause RF receive error. The product lifetime may shorten if used at places with hydrogen sulfide such as at a hot spring. Data communication will be disabled or a data file may corrupt if the PC is turned off or the product is separated from the PC during the communication. Important data must be verified against the original data. For fixing the product, use the enclosed fixture. When connecting the product onto PC, use the enclosed USB cable or LAN cable. Both a USB and an Ethernet interface cannot be used simultaneously in case a UTD model. When using UTD model, Please put the antenna at vertical position as shown in the below diagrams so that the unit could acquire proper antenna characteristics. Kyocera Corporation -7- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 1 Introduction This chapter describes what should should be confirmed before using iBurst Terminal. Terminal. Kyocera Corporation -8- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Components List The table below shows the list of components. Please confirm items in the package. UTD model Component iBurst Terminal AC/DC Adapter Power Cable USB Cable 10-Base-T Ethernet Cable Notes Q’ty Q’ty Unit of UTD model Refer to the pictures shown in next page. Input: 100 - 240V AC/ 50 - 60Hz/ 300mA Output: 9V DC/ 1.2A Cable Length of output side: 2m Length: 2m Type: USB1.1 Length: 1m Type: Straight through/ Category 5 Length: 2m UTU model Component iBurst Terminal USB Cable Notes Q’ty Q’ty Unit of UTU model Refer to the pictures shown in next page. Type: USB1.1 (Mini B for UTU side) Length: 1m Pictures of Accessories AC/DC Adapter Kyocera Corporation -9- Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Outlook of iBurst Terminal UTD model Antenna Power switch Back side view Power Indicator Link/Communication Indicator USB port PC Connection Indicator 10Base-T port only on UTD model DC Power Input Kyocera Corporation - 10 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual UTU model Link/Communication Indicator Power Indicator External antenna port USB port Indicators Indicators The table below describes meaning of each indicator. Indicator Power Indicator Link/Communication Indicator State OFF Blue Blinking OFF Amber Yellow Green PC Connection Indicator (Only on UTD model) Kyocera Corporation OFF Amber Green Meaning Turned OFF Turned ON Fault Turned OFF No signal receiving Weak signal receiving Blinking when communicating. Strong signal receiving Blinking when communicating. Any port not active USB port 10Base-T port - 11 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Requirements on your PC • PC/AT Compatible PC with WindowsXP/2000/Me/98SE; or version 10.1.5 or later version of Mac OS X except Mac Intel model. • 1 USB1.1 port or a later version of USB port. NOTE: • In case of using USB connection. 1 10Base-T Ethernet port or compatible. NOTE: In case of using 10Base-T Ethernet connection with a UTD model. Outlook to use the iBurst Terminal A UTD model has 1 USB port and 1 10Base-T Ethernet port and a UTU model has only 1 USB port. The USB port, or 10Base-T Ethernet port, shall be connected with your PC. Before connecting the USB interface, you have to install iBurst software which includes device drivers. If you want to utilize 10Base-T connection, you don’t have to install the software in case Windows XP or Mac OS X. Please read through every sections related with the operating system for details. USB Connection Back side of UTD UTU USB port USB Cable 10Base-T Ethernet Connection 10Base-T port Category 5 Cable (Straight cable) Kyocera Corporation - 12 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Chapter 2 Setup Procedure This This chapter describes how to install iBurst software, then guides you how to make a network connection so as to use data communication service. Kyocera Corporation - 13 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual iBurst Software Installation Installation This section shows the procedure to install iBurst software on your PC for utilizing iBurst Terminal. The procedure shall be done once before using it. Installation Installation for Windows XP NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you don’t need to install/uninstall any iBurst software. In such case, you can skip this section and you need only to create a dial-up connection setting described at from page 62. You can see indications of the iBurst Terminal over Ethernet. See page 87 for the method. 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Terminal Setup starts. Click the [Next >] button. Kyocera Corporation - 14 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 5. Select [I accept the terms the license agreement], click the [Next >] button. 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. Kyocera Corporation - 15 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 8. The following dialog window will appear, and installation of software begins. 9. When the installing process finishes, the dialog window shown below will appear. Select “Yes, I want to restart my computer now” and click the [Finish] button in the dialog window. 10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port. The iBurst Terminal will be recognized and will be ready to use automatically. NOTE: If the PC request to restart again, click [Yes] to restart the PC. NOTE: To connect to the Internet, refer to page 62. Kyocera Corporation - 16 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Windows 2000 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Terminal Setup starts. Click the [Next >] button. 5. Select [I accept the terms the license agreement], click the [Next >] button. Kyocera Corporation - 17 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation - 18 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 9. When the installing process finishes, the dialog window shown below will appear. Select [Yes, I want to restart my computer now] and click the [Finish] button in the dialog window. 10. After finish of restarting, connect the iBurst Terminal with your PC’s USB port. The iBurst Terminal will be recognized and will be ready to use automatically. NOTE: If the PC request to restart again, click [Yes] to restart the PC. NOTE: To connect to the Internet, refer to page 67. Kyocera Corporation - 19 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Windows Me Me Since the the installation disk of Windows Me may be be required while driver installation, please prepare the CD or copy the CD into a hard disk in your PC for it. 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Terminal Setup starts. Click the [Next >] button. 5. Select [I accept the terms the license agreement], click the [Next >] button. Kyocera Corporation - 20 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation - 21 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 9. Click the [Finish] button. 10. Click the [OK] button. NOTE: Refer to the 1st article in chapter 6, if you face such symptom described in the attention message. NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you can skip from hear to step 18 and continue from step 19 in this section. You can see indications of the iBurst Terminal over Ethernet. See page 87 for the method. 11. Connect the iBurst Terminal with your PC through a USB cable. Windows will detect the iBurst Terminal as a new hardware so that [Add New Hardware Wizard] will begin. Kyocera Corporation - 22 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 12. Select [Specify the location of the driver (Advanced)] and click the [Next >] button in the dialog window. 13. Select [Search for the best driver for your device.(Recommended)], then check [Specify a location] and click the [Browse] button. 14. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. Kyocera Corporation - 23 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 15. Click the [Next >] button. 16. Confirm that the device name [iBurst Terminal] is displayed in the dialog window, then click the [Next >] button. 17. Click the [Finish] button. Kyocera Corporation - 24 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 18. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. 19. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add New Hardware]. 20. Click the [Next >] button. Kyocera Corporation - 25 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 21. Click the [Next >] button. NOTE: If the dialog window shown below appears, select [No, the device isn’t in the list] and click the [Next >] button. 22. Select [No, I want to select the hardware from a list], and click the [Next >] button. Kyocera Corporation - 26 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 23. Select [Ports (COM & LPT)], and click the [Next >] button. 24. Click the [Have Disk..] button. 25. Click the [Browse...] button. Kyocera Corporation - 27 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 26. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 27. Click the [OK] button. 28. Select [iBurst Terminal Virtual COM Port], and click the [Next >] button. Kyocera Corporation - 28 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 29. Click the [Next >] button. 30. Click the [Finish] button. 31. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. 32. Turn your PC on again. Kyocera Corporation - 29 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 33. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Modems]. NOTE: If the dialog window as shown below appears, click the [Add] button. Kyocera Corporation - 30 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 34. Check [Don’t detect my modem; I will select it from a list], and click the [Next >] button. 35. Click the [Have Disk..] button. 36. Click the [Browse…] button. Kyocera Corporation - 31 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 37. Select [C:\Program Files\iBurst Terminal\bin],and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 38. Click the [OK] button. 39. Select [iBurst Terminal Virtual MODEM], and click the [Next >] button. Kyocera Corporation - 32 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 40. Select [iBurst Terminal Virtual COM Port (COM X)], and click the [Next >] button. NOTE: The ‘X’ in “COM X” above is a COM port number assigned automatically. NOTE: If the dialog window as shown below appears, type a dummy number in “What are (or city) code are you in now ?” and then click the [Next >] button. 41. Click the [Finish] button. Kyocera Corporation - 33 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 42. Click the [OK] button. 43. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation - 34 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 44. Click the [Add…] button on [Configuration] tab. 45. Select [Protocol] and click the [Add…] button. 46. Click the [Have Disk…] button. Kyocera Corporation - 35 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 47. Click the [Browse…] button. 48. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 49. Click the [OK] button. Kyocera Corporation - 36 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 50. Select [NDIS(PPPoE) Usermode I/O Protocol for iBurst Terminal], click the [OK] button. NOTE: If the same dialog at step 46 is popped up again, cancel once and repeat from step 44. 51. Click the [OK] button. NOTE: For USB connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol for iBurst Terminal -> iBurst Terminal” must be added automatically. For Ethernet connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol for iBurst Terminal -> The name of the Ethernet Network Interface Card or Port” shall be added automatically. Kyocera Corporation - 37 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 52. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. NOTE: To connect to the Internet, refer to page 67. Kyocera Corporation - 38 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Windows 98SE Since the the installation disk of WINDOWS 98SE may be required while driver installation, please prepare the CD or copy the CD into a hard disk in your PC for it. 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. 4. iBurst Terminal Setup starts. Click the [Next >] button. 5. Select [I accept the terms the license agreement], click the [Next >] button. Kyocera Corporation - 39 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 6. Click the [Next >] button after appearing dialog window as shown below. NOTE: To install to a different folder, click [Browse…] and specify another folder. 7. Click the [Next >] button. 8. The following dialog window will appear, and installation of software begins. Kyocera Corporation - 40 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 9. Click the [Finish] button. 10. Click the [OK] button. NOTE: Refer to the 1st article in chapter 6, if you face such symptom described in the attention message. NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you can skip from hear to step 19 and continue from step 20 in this section. You can see indications of the iBurst Terminal over Ethernet. See page 87 for the method. 11. Connect the iBurst Terminal with your PC through a USB cable. Windows will detect the iBurst Terminal as a new hardware so that [Add New Hardware Wizard] will begin. Kyocera Corporation - 41 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 12. Click the [Next >] button in the dialog window. 13. Select [Search for the best driver for your device.(Recommended)], and then check the [Next >] button. 14. Check [Specify a location] and click the [Browse] button. Kyocera Corporation - 42 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 15. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. 16. Click the [Next >] button. 17. Confirm that the device name [iBurst Terminal] is displayed in the dialog window, then click the [Next >] button. Kyocera Corporation - 43 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into the CD-ROM drive and click the [OK] button. NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into your PC and enter the directory of your [Windows 98SE CD-ROM], click the [OK] button. “xxxxxxxx“ in the picture below is a file name that can not be found. 18. Click the [Finish] button. 19. The dialog window shown below will appear, click the [Yes] button, and restart your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. Kyocera Corporation - 44 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 20. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Add New Hardware]. 21. Click the [Next >] button. 22. Click the [Next >] button. Kyocera Corporation - 45 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, select [No, the device isn’t in the list] and click the [Next >] button. 23. Select [No, I want to select the hardware from a list.], and click the [Next >] button. 24. Select [Ports (COM & LPT]], and click the [Next >] button. Kyocera Corporation - 46 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 25. Click the [Have Disk..] button. 26. Click the [Browse…] button. 27. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. Kyocera Corporation - 47 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 28. Click the [OK] button. 29. Select [iBurst Terminal Virtual COM Port], and click the [Next >] button. 30. Click the [Next >] button. Kyocera Corporation - 48 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into the CD-ROM drive and click the [OK] button. NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into your PC and enter the directory of your [Windows 98SE CD-ROM],click the [OK] button. “xxxxxxxx“ in the picture below is a file name that can not be found. 31. Click the [Finish] button. 32. The dialog window shown below will appear, click the [Yes] button to SHUTDOWN your PC. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. Kyocera Corporation - 49 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 33. Turn your PC on again. 34. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Modems]. NOTE: If the dialog window as shown below appears, click the [Add] button. Kyocera Corporation - 50 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 35. Select [Other], and click the [Next >] button. 36. Check [Don’t detect my modem, I will select it from a list] and click the [Next >] button. 37. Click the [Have Disk…] button. Kyocera Corporation - 51 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 38. Click the [Browse…] button. 39. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 40. Click the [OK] button. 41. Select [iBurst Terminal Virtual MODEM], and click the [Next >] button. Kyocera Corporation - 52 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 42. Select [iBurst Terminal Virtual COM Port (COM X)], and click the [Next >] button. NOTE: The ‘X’ in “COM X” above is a COM port number assigned automatically. NOTE: If the dialog window as shown below appears, type a dummy number in “What are (or city) code are you in now ?” and then click the [Next >] button. 43. Click the [Finish] button. Kyocera Corporation - 53 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 44. Click the [OK] button. 45. Click the [Start] -> [Settings] -> [Control Panel] to open Control Panel as shown below, and then double click [Network]. Kyocera Corporation - 54 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 46. Click the [Add] button on [Configuration] tab. 47. Select [Protocol] and click the [Add…] button. 48. Click the [Have Disk…] button. Kyocera Corporation - 55 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 49. Click the [Browse…] button. 50. Select [C:\Program Files\iBurst Terminal\bin], and click the [OK] button. NOTE: You don’t have to select a file name. Windows will find an appropriate file automatically. 51. Click the [OK] button. Kyocera Corporation - 56 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 52. Select [NDIS(PPPoE) Usermode I/O Protocol for iBurst Terminal], click the [OK] button. NOTE: If the same dialog at step 47 is popped up again, cancel once and repeat from step 45. 53. Click the [OK] button. NOTE: For USB connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol for iBurst Terminal -> iBurst Terminal” must be added in this stage. For Ethernet connection with iBurst Terminal, “NDIS(PPPoE) User mode I/O Protocol for iBurst Terminal -> The name of the Ethernet Network Interface Card or Port” shall be added in this stage. Kyocera Corporation - 57 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into the CD-ROM drive and click the [OK] button. NOTE: If the dialog window as shown below appears, insert [Windows 98SE CD-ROM] into your PC and enter the directory of your [Windows 98SE CD-ROM],click the [OK] button. “xxxxxxxx“ in the picture below is a file name that can not be found. 54. The dialog window shown below will appear, click the [Yes] button, and shut down your PC, then turn on your PC again. NOTE: If the PC doesn’t shutdown itself, try to press Alt+Ctrl+Del keys several times. NOTE: To connect to the Internet, refer to page 67. Kyocera Corporation - 58 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual Installation for Mac OS X NOTE: If you are going to connect the iBurst Terminal with your PC only through an Ethernet cable, not through a USB cable, you don’t need to install/uninstall any iBurst software. In such case, you can skip this section and you need only to create a dial-up connection setting described at from page 69. Please note that you cannot utilize the iBurst utility software described in chapter 3. NOTE: The installation software are applied to Mac OS X 10.1.5/10.2/10.3/10.4 except Mac Intel models. Make sure OS version on your PC and a corresponding installation software package for iBurst Terminal. NOTE: All screen copies in this section are based on Mac OS X 10.1.5. 1. Make sure to disconnect the iBurst Terminal with your PC. ATTENTION: Don’ Don’t connect the iBurst Terminal with your PC through a USB cable until completion of installation. 2. Turn your PC on and login as an administrative user. 3. Insert the Software Utility CD provided by the network operator into your CD-ROM drive; or execute the appropriate installation software. NOTE: If the window shown below appears, click “Click the lock to make changes”. Kyocera Corporation - 59 - Revision 1.01 --- June.08.2006 iBurst Terminal, Desktop Model (UTD) / USB Model (UTU), Manual 4. In case of version 10.3 or later, the confirmation message shown below will appear. Click [Continue] button. 5. In case of version 10.2 or older, “Authenticate” dialog will appear. Enter an administrator name and password, and then click the [OK] button. 6. Click the [Continue] button. Kyocera Corporation - 60 - Revision 1.01 --- June.08.2006
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 60 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-14, framework 1.6 About : uuid:f93ef4c3-84cc-43a0-b501-fcf4d70fcbfb Producer : AFPL Ghostscript 8.13 Modify Date : 2006:08:21 20:18:31+09:00 Create Date : 2006:08:21 20:12:24Z Creator Tool : PrimoPDF http://www.primopdf.com Metadata Date : 2006:08:21 20:18:31+09:00 Document ID : uuid:b91ac915-9cf0-4c26-9a3a-64985a994bf5 Format : application/pdf Title : Microsoft Word - Q38T-EE-001_UTdUsersManualR101 for FCC.doc Creator : yamamoto Author : yamamotoEXIF Metadata provided by EXIF.tools