Kyodo West KG50640 Multi-bandwidth UHF Transceiver User Manual Revised User Instructions2

Kyodo West Inc Multi-bandwidth UHF Transceiver Revised User Instructions2

users manual

Download: Kyodo West KG50640 Multi-bandwidth UHF Transceiver User Manual Revised User Instructions2
Mirror Download [FCC.gov]Kyodo West KG50640 Multi-bandwidth UHF Transceiver User Manual Revised User Instructions2
Document ID251210
Application IDNViC+kEZ9Cyyc38VzxYM5A==
Document Descriptionusers manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize9.84kB (123042 bits)
Date Submitted2002-06-19 00:00:00
Date Available2002-06-17 00:00:00
Creation Date2002-06-14 14:04:38
Producing SoftwareAcrobat PDFWriter 4.05 for Windows
Document Lastmod0000-00-00 00:00:00
Document TitleRevised User Instructions2
Document CreatorRevised User Instructions2.doc - Microsoft Word

OPERATOR’S MANUAL
KYODO WEST MODEL KG506
FULL-DUPLEX MOBILE
Preliminary
1.0
INTRODUCTION
Thank you for purchasing the KYODO WEST MODEL KG506 Full-Duplex Mobile Radio. This manual
contains information to assist you in the application and operation of the radio.
The KG506 is a building block intended for use in systems requiring a compact radio for full duplex,
repeater, link, etc. The radio is capable of both analogue and digital modulation.
The KG506 is designed to operate with an external, custom designed, control system, which may be
supplied by Kyodo West or by the customer. Kyodo West will provide engineering assistance and
technical information to assist in the design of the control system by the customer.
Use of the many features available in the radio will depend on the complexity of the control system.
2.0
FEATURES & PRODUCT DESCRIPTION
2.1
Standard Inclusions
The KG506 transceiver is supplied complete with the following items:
KG506 transceiver
DC Supply Cable with Fuse and Plug
Operators Manual
Spare Fuse
Two Magnetic Keys
Mounting Plate with Hardware
2.2
Features
§
§
§
§
§
§
§
§
§
§
§
2.3
Designed for use with external control system
Simplex or two frequency Duplex operation
EEPROM programmable with a PC computer
Up to 64 Channels
Optional Internal Duplexer
All FM Frequency Bands from 66 to 520 MHz
Transmit Time Limiter to prevent channel
jamming
TX and RX Encryption
All-Scan and Program Scan Scanning Modes
5 Tone Encoder & Decoder plus DTMF Encoder
& Decoder
22, 26, or 35 MHz switching bandwidth (model
dependant)
§
§
§
§
§
§
§
§
§
Two-Stage Front End allows mixed Simplex and
Duplex operation
Channel selectable Wide or Narrow channel
spacing
Channel selectable High / Low power
CTCSS/DCS on a per channel basis
Rugged Housing
Heavy gauge mounting plate with key lock
Step-Up VCO Voltage for Superior Selectivity
Low Stand-by Current is ideal for Solar
Installations
Watch Dog Timer
Product Description
The Kyodo West KG506 transceivers represent a great advance on the previous rugged & time proven
KG106 transceiver. They consist of separate modules all housed within one rugged, compact mobile
cabinet. The receiver, the transmitter, and the PA Unit are each enclosed within their own diecast
housings that are directly mounted to the main chassis. A full-featured logic module controls all
parameters of the radio under the control of a microprocessor. The RF Power Output is 1 - 30 Watts on a
continuous duty basis. The CTCSS module supports all EIA tones, which may be set on a per channel
basis during radio programming.
The KG506 is supplied with TX and RX antenna ports to allow connection to an external duplexer or
feeder cables. Space is provided inside the housing for an antenna relay or mobile type 6-cavity duplexer.
MODEL KG506 FULL-DUPLEX MOBILE
2.4
Front Panel Features
The front
1.
2.
3.
4.
5.
6.
7.
8.
panel includes the following:
UHF Type connector for the Transmitter (optional type “N”)
LEDs to indicate: A=POWER, B=BUSY, C=TRANSMIT, D=ALARM, and E=REPEAT
Miniature jack for speaker audio output
BNC Connector for the Receiver
DC Power Connector
25 position D sub connector for interface to the external control system
9 position D sub connector for connection to a PC for programming
Model Number / FCC Label
2.5
Indicator Functions
POWER On Indicator LED
The Power ON Indicator LED will illuminate in Green (Blue on FCC sample) color whenever the
Power ON/OFF switch is switched to the "ON" position.
BUSY Mode Indicator LED
The Busy Mode Indicator LED will illuminate in Green color whenever the KG506 receives a carrier
signal on the selected channel that is greater then the Squelch setting.
TRANSMIT Mode Indicator LED
The Transmit Mode Indicator LED will illuminate in Red color whenever the KG506 is transmitting.
ALARM Mode Indicator LED
The Alarm Mode Indicator LED will illuminate (Flashing) in Amber color whenever the transceiver
detects a fault in the receiver module, the transmitter module, or the PA module on the selected
channel.
REPEATER Mode Indicator LED
The Repeater Mode Indicator LED will illuminate in Yellow color when the selected channel has
been programmed for Repeater operation. This LED will NOT illuminate on any channel that is
programmed to operate in Base Station mode.
MODEL KG506 FULL-DUPLEX MOBILE
3.0
OPERATION
3.1
Installation and Programming
KG506 can be installed to operate as a Transportable, Mobile or a Fixed Station in any mode of
operation.
The KG506 must be programmed before it will operate correctly. This is best done by the
equipment supplier or a competent radio engineer. They will require the correct programming kit
and a computer. Complete programming instructions are provided with the kit. If a duplexer is
used, please observe the maximum frequency range permitted by the duplexer notches.
It is important that the KG506 be correctly installed at its working location. It is recommended that
this be done by a competent radio engineer.
As a minimum, it is necessary to:
The antenna(s) used for this transmitter must be fixed-mounted on outdoor permanent
structures. RF exposure compliance is addressed at the time of licensing, as required by
the responsible FCC Bureau(s), including antenna co-location requirements of 1.1307(b)(3).
•
•
•
•
3.2
Securely attach the mounting plate to the desired location.
Connect the DC Input power lead to a suitable 13.8 Volt Regulated DC Power supply that
has sufficient capacity. (Ensure that the DC Polarity is correct, otherwise the fuse will
blow).
Connect the antenna feed line(s). (Check that the VSWR of the antenna is acceptable).
Connect the Control System to the 25 position sub D connector.
Basic Operation
Note that controls and functions will vary with different control systems and with programming.
3.2.1
Switch On
Switch the KG506 "ON" , the POWER indicator should illuminate.
3.2.2
Adjust the Volume Setting
Rotate the Volume Knob clockwise until the audio level from the speaker is suitable.
3.2.3
Adjust the Squelch Setting
Rotate the Squelch Knob clockwise (from the fully counter clockwise position) slowly until
the background noise can no longer be heard. It is wise to slightly rotate the knob further
in the clockwise direction so that variations in the background noise level do not "break"
the squelch setting and cause annoying noises to be heard from the speaker.
3.2.4
Select the Channel
Select the desired channel.
3.2.5
Receiving
You should now be able to hear any radio traffic that occurs on channel. It may be
necessary to further slightly adjust the Volume setting to suit your listening requirements.
3.2.6
Transmitting
Depending on the legal requirements in your country and the operating requirements
within your organization, it may be necessary to announce your Call Sign, and will
MODEL KG506 FULL-DUPLEX MOBILE
probably be necessary to announce the Call Sign of the party you are calling at the start
of your transmission.
Press the PTT switch before beginning to speak. When transmitting, it is necessary to
hold the microphone about 75mm (3") from your mouth and speak clearly into the grill of
the microphone.
4. CIRCUIT DESCRIPTION
4.1
Receiver
1) RF section
An incoming signal is fed to pre-selector, BPF-101/103, and amplified by Q101/Q102, and then
fed to post-selector BPF-102/104. The outputs of the RF section(s) feed the balanced mixer,
st
consisting of T101, T102, D107 and D108, which produces 48.5MHz by injection from the 1
local oscillator signal provided by the RX VCO.
2) IF & Audio Sections
The output signal from the balanced mixer is fed to the crystal filters XF101, and then amplified
by Q103. This signal is fed to crystal filters XF102 A & B and amplified by Q113. The signal is
nd
nd
fed to 2 processor IC (IC106). The 2 local crystal oscillator signal is fed to IC106 to produce
nd
nd
the 2 (Low IF) signal of 455 KHz. IC106 amplifies and detects the 455 Low IF 2 local signal to
produce an audio signal. Then, the audio signal is fed to the low-pass filter inclusive in IC107,
and fed to audio processor IC (IC3) located on the Logic Unit. IC3 provides band-pass and deemphasis functions and passes the processed audio to IC16, line amplifier and IC22, Audio PA.
IC16 provides internal repeat audio and external “0 dBm” audio for interfacing external devices.
IC22 provides audio to the speaker jack.
3) RX VCO Section
st
The oscillator circuit formed by Q301 and associated components produces the 1 local signal
(Rx frequency minus 48.5MHz). The frequency of the oscillator is controlled by a signal input
st
from the PLL, (see below) which is applied to varactors D303/304. The 1 local signal is
amplified by buffer amplifier Q302, and again IC301 and Q303. The output signal is fed to the
balanced mixer in the receiver RF section. A sample of the frequency is also sent to the PLL.
4) RX PLL Section
The PLL IC101 contains a pre-scaler and frequency dividers to divide both the VCO frequency
and the local TCVXO, 12.0 MHz to a common reference frequency. These signals are compared
by a phase detector to produce a VCO control signal. This control signal is fed to the charge
pump, consisting of Q108, Q109 and Q110, and fed to the LPF IC103 and on to the VCO. The
supply voltage of the charge pump is multiplied by IC102 (approx. 15V) to achieve greater C/N
ratio. The frequency dividers are controlled by data from the Logic Unit to determine receiver
operating frequency.
4.2
Transmitter
1) TX VCO section
The oscillator circuit formed by Q301 and associated components produces the final carrier
signal. The frequency of the oscillator is controlled by a signal input from the PLL, (see below)
which is applied to varactors D303/304. The oscillator signal is amplified by buffer amplifier
Q302, and again IC301 and Q303. The output signal is fed to the TX (driver) Unit for further
amplification. A sample of the frequency is also sent to the PLL. The modulation is applied to
varactors D301 and D302.
2) TX PLL section
The PLL IC101 contains a pre-scaler and frequency dividers to divide both the VCO frequency
and the local TCVXO, 12.0 MHz to a common reference frequency (5 to 15 KHz.). These signals
MODEL KG506 FULL-DUPLEX MOBILE
are compared by a phase detector to produce a VCO control signal. This control signal is fed to
the charge pump, consisting of Q206, Q207 and Q208, and fed to the LPF IC207 and on to the
VCO. The supply voltage of the charge pump is multiplied by IC208 (approx. 15V) to achieve
greater C/N ratio. The frequency dividers are controlled by data from the Logic Unit to determine
transmitter operating frequency
3) Modulator Section
The modulation signal is fed to both VCO and the reference oscillator (TCVXO). This permits a
very flat modulation characteristic against low frequency (DC). This permits operation with digital
signals such as Digital Coded Squelch and POCSAG Paging Terminals.
4) TX Unit (Driver) Section
The VCO signal is amplified by Q215 to the proper level to drive the PA Module.
5) PA Section
The signal from driver stage is fed to PM501 to achieve 30W output power. The signal is then fed
to a balanced line to detect forward and reverse power, then on to the LPF to eliminate
harmonics spurious frequencies. An APC (Automatic Power Control) circuit stabilizes the output
power at the set level. The circuit also protects the PA from excess reverse power caused by
mis-match of the antenna. An alarm circuit signals if output power drops below a preset level or
when SWR exceeds a preset level. All parameters are adjustable.
4.3
Logic Unit
1) Microcomputer (CPU)
CPU, IC1, uPD78F0058, an 8-bit processor, has 60K flash memory and 2K RAM inside. This CPU
controls all functions of KG506. A flash memory permits ON-BOARD-UP-GRADE when new
software is released.
2) EE ROM section
IC7 is the 64kbit EEROM. This IC contains all channel parameters.
3) Audio processor section
An IC2 is for TX and IC3 is for RX audio processor. These IC’s control all audio processing and
encode/decode CTCSS tones commanded by the CPU. These IC’s are also contain a 2400bps
MODEM to enable use of MPT1327 trunking protocols by using external MPT control software.
4) LED display section (front panel of radio)
The LED’s indicate each mode of operation of the KG506 as follows:
POWER, BUSY, TRANSMIT, ALARM, REPEATER.
5) Audio amplifier section
An IC22 provides 5 W audio power to drive 8 ohm external speaker.
4.4
Control Interface Connector
A 25 position D-sub connector for remote control is provided on the front panel of KG506.
The functions of each pin are as follows;
1 CH 0, 1
apply 1 to 6 bits of binary input to pins 1 thru 6 to select 64 channels,
2 CH 1, 2
Pin 1 is LSB.
3 CH 2, 4
4 CH 3, 8
5 CH 4, 16
6 CH 5, 32
7 GROUND
Ground
MODEL KG506 FULL-DUPLEX MOBILE
8 RSSI
9 DISC. OUT
10 SQ. CONT.
11 BUSY
12 MUTE
13 MOD-1
14 GROUND
15 PTT
16 MOD-2
17 SIMPLEX
18 ERROR
19 DECODE
20 RX AUD-1
21 RX AUD-2
22 TX OUT
23 EXT. POW SW
24 VOLUME
25 +12V (nom)
CN1 Mini phone jack
5.
5.1
Receive Signal Strength Indication, 0 to 5 V DC
Discriminator audio output, low level
To external Squelch control, 10K pot to ground
Goes to 5V logic high when squelch is opened by signal
When pulled low, mutes RX and Repeat audio
Microphone modulation input
Ground
Pull low to transmit
Digital modulation input, DC sensitive
Provides logic output during simplex operation
Provides “flashing” high/low if error/alarm is present
Logic low upon decoding 5-tone or DTMF code
With pin 21, provides balanced “0 dBm” audio
With pin 20, provides balanced “0 dBm” audio
Indicates error in PA, low power or high SWR
Connect to ground through external POWER switch
To external volume control, 10 K pot to ground
Switched 12 VDC to external accessories
Balanced Speaker output both sides above ground.
ALIGNMENT PROCEDURES
Receiver Unit
1) BPF-101 and BPF-102, RF Alignment
Connect the signal generator to the Rx antenna connector of KG506. Align the BPF-101 and
BPF-102 to obtain the maximum sensitivity. For better alignment, if you have spectrum analyzer
and tracking generator, connect the tracking generator to the Rx antenna connector and pick up
the output signal from J101 to connect spectrum analyser. Align the BPF-101 and BPF-102 to
cover the desired bandwidth of receive frequencies. If receiver is equipped with the optional dual
RF sections, adjust BPF-103 and BPF-104 as above.
2) FVR101 alignment
This is to adjust the tight squelch level. Set to threshold with external squelch control set to 1/2
rotation.
3) VCO alignment
The VCO has been aligned at the factory to cover full bandwidth. However, if you must re-adjust
the VCO due to repair, set the VCO voltage at 10.5V by L303 at the highest sub-band frequency.
5.2
Transmitter Unit
Note: there are no tuning adjustments for the transmitter. It is a broadband circuit.
1) FVR201 alignment
This potentiometer determines the modulation balance. Carefully align this potentiometer to
obtain equal deviation on the lowest and the highest RF frequency programmed into the
transmitter (not required for normal frequency spreads).
2) FVR202 alignment
This potentiometer determines the low frequency (below 300Hz) deviation. When POCSAG,
CTCSS or DCS are used, it is necessary to adjust to have enough deviation at low frequency.
Adjusts for flat slope on low frequency square wave tests.
3) FVR203 alignment
MODEL KG506 FULL-DUPLEX MOBILE
This potentiometer sets the maximum deviation, normally set below 5KHz. Programming
automatically sets to below 2.5KHz deviation for narrow spacing.
4) FVR204 alignment
Adjust the transmitter output power to 30 W or less.
5) VCO alignment
The VCO has already been aligned at the factory; however if you need to re-adjust, set the VCO
voltage at 10.5V at the highest sub band frequency.
5.3
Power Amplifier (PA Unit)
1) FVR501
Terminate KG506 with 50 ohm load, and adjust this potentiometer for the minimum level of
reverse power.
2) FVR502
This potentiometer sets the SWR alarm threshold when the transmitter is terminated with 50
ohms load. Set just slightly past the alarm point.
3) FVR503
Adjust this potentiometer for the low power alarm threshold, usually –3dB. Turn power down to
12.5 watts (using FVR504) and adjust FVR503 for alarm to trigger.
4) FVR504
Adjust for maximum power output, but do not exceed 35W.
5.4
Logic Unit
Note: some adjustments are repeated here for clarity.
1) FVR1 adjustment
Not used.
2) FVR2 adjustment
Adjusts the deviation level when the KG506 used as a repeater. Set to 3.5 kHz modulation with
receiver modulated at 3.5 KHz.
3) FVR3 adjustment
Adjusts the TX output power (hi power level), usually set to 25 W. Will not exceed level set in
Step 5.3.4.
4) FVR4 adjustment
Adjusts Low Power level when program calls for low power. Usually set to 10 to 15 W.
5) FVR5 adjustment
Internal Squelch range control; if necessary, adjust for threshold with external control set to 1/2
rotation.
6) FVR6 adjustment
Adjusts 600 Ohm RX output level at pins 20 & 21 of 25 pin interface connector, usually set to 0
dBm balanced output.
7) FVR7 adjustment
Internal volume control, used to set maximum audio output power into the speaker. With
external Volume Control set to maximum, adjust for 5 watts or less at speaker.
MODEL KG506 FULL-DUPLEX MOBILE
8) FVR8 adjustment
Used for auxiliary audio input.
MODEL KG506 FULL-DUPLEX MOBILE
9) FVC1 adjustment
This is to shift the CPU clock frequency. This is to eliminate beat interference with certain
carrier frequencies.
10) FVC2
This is to shift clock frequency for IC2 and IC3, also to eliminate beat interference with certain
carrier frequencies.
MODEL KG506 FULL-DUPLEX MOBILE
10
6.
SPECIFICATIONS
6.1 General
Frequency Range
Version SA
Version A
Version B
Version C
Version DS
Version D
Version E
Version F
300 335 365 400 420 440 465 485 -
Number of Channels
Channel Spacing
Operation Mode
Antenna Impedance
Power Supply
Consumption
Environmental Conditions
Dimensions
Weight
335MHz
370MHz
400MHz
435MHz
455MHz
475MHz
500MHz
520MHz
64 channels (observe duplexer limitations )
12.5/20/25/30KHz
Semi Duplex/Full Duplex
50 ohm unbalanced
DC 13.6V negative ground only (external)
8 amperes or less
-30 to +60 degree C, 95% humidity @35C
220 (w) 82 (h) 347 (d) mm
6 kgs.
6.2 Transmitter
Output Power
Switchable Bandwidth
Frequency Deviation
Frequency Stability
Frequency Response
Signal to Noise Ratio
Modulation Distortion
Spurious & Harmonics
25W continuous, 30W maximum
Full sub-band
5KHz(wide band) 2.5KHz(narrow band)
+/- 1KHz
Within +1, -3dB, 300-3000Hz @1KHz ref.
50dB or more @1KHz 70% mod. (45dB at narrow)
3% or less
0.25uW or less
6.3 Receiver
Switchable Bandwidth
IF Frequencies
Frequency Stability
Sensitivity
Squelch Sensitivity
Selectivity
Blocking
Intermodulation
Spurious Response
AF Response
AF Distortion
Signal to Noise Ratio
4MHz
st
nd
1 IF 48.5MHz, 2 IF 455KHz
+/- 1KHz
0.4uV or less for 20dB N.Q. / 0.3uV for 12dB SINAD
0.25uV or less
70dB or more at 25KHz
90dB or more
70dB or more
70dB or more
Within +1, -3dB, 300-3000Hz @1KHz ref.
5% or less @1KHz 70% mod
50dB or more @1KHz 70% mod. (45dB at narrow)
MODEL KG506 FULL-DUPLEX MOBILE
11

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 11
Creator                         : Revised User Instructions2.doc - Microsoft Word
Create Date                     : 2002:06:14 14:04:38
Title                           : Revised User Instructions2
Producer                        : Acrobat PDFWriter 4.05 for Windows
EXIF Metadata provided by EXIF.tools
FCC ID Filing: IOJKG50640

Navigation menu