LANKE XUNTONG TECHNOLOGY PTR9618 Bluetooth low energy 4.0 modules User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3311432
Application ID	UkNcy+9sVu51GlMP9z4ETQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	57.97kB (724678 bits)
Date Submitted	2017-03-10 00:00:00
Date Available	2017-03-10 00:00:00
Creation Date	2017-03-09 10:28:34
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2017-03-09 19:05:16
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 11 Word 版
Document Author:	MCU

PTR9618
Bluetooth Low Energy 4.0 Module
Embedded Cortex™ M4F 32 bit processor
The PTR9618 ultra-low power Bluetooth Low Energy/ANT/2.4GHz Proprietary
Multi-protocol modules based on the nRF52832 from Nordic Semiconductor. The module
with an ARM® Cortex™ M4F 32 bit processor, embedded 2.4GHz transceiver, and
integrated antenna, provide a complete solution with no additional RF design, allowing
faster time to market, while simplifying designs, reducing BOM costs, also reduce the
burden of Regulatory approvals to enter the world market. Making you more quickly into
the bluetooth smart application and remove the worries.
Features

System on Module(SOM) base on Nordic nRF52832

Bluetooth Low Energy/ANT/2.4GHz Proprietary Multi-protocol support

Complete Bluetooth Low Energy stack/profiles solution (Bluetooth 4.x and Higher)

ARM® Cortex™-M4F 32 bit processor, 512 kB flash memory, 64 kB RAM

32 General Purpose I/O, Configurable mapping Pins, Simple layout of external application

12-bit/200KSPS ADC

Three SPI Master/Slave (8 Mbps)

Low power comparator, Temperature sensor, Random Number Generator

Two 2-wire Master/Slave (I2C compatible)

I2S audio interface, PDM audio interface

UART (w/ CTS/RTS and DMA)

3x4-channel PWMs

20 channel CPU independent Programmable Peripheral Interconnect (PPI)

Quadrature Demodulator (QDEC)

128-bit AES HW encryption

5 x 32bit Timers, 3 x 24bit Real Timer Counters (RTC), Watchdog Timer

NFC-A tag interface for OOB pairing

Internal RC Oscillator 32.768 kHz(± 250 ppm).

No external components required

Over-the-Air (OTA) firmware updates available

Dimensions: 22.7mmx17.5mm x1.8mm with Antenna，1.27mm pin pitch.
COPYRIGHT ©2017 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Typical Applications:













- 2.4 GHz Bluetooth low energy systems
- Proprietary 2.4 GHz systems
- Sports and leisure equipment
- Mobile phone accessories, Connected Appliances
- Health Care and Medical
- Consumer Electronics, Game pads
- Human Interface Devices, Remote control
- Building environment control / monitoring
- RFID, Security Applications，Low-Power Sensors
- Bluetooth Low Energy GateWay
- iBeacons™, Eddystone™, Indoor navigation
- Lighting Products
- Fitness devices, Wearables
Quick Specifications:
Multi-protocol
Version
Bluetooth 4.0 /ANT/2.4GHz Proprietar
Security
AES-128
Radio
Frequency
2.402GHz to 2.480GHz
Modulations
GFSK at 1 Mbps, 2 Mbps data rates
Transmit power
+4 dBm
Receiver sensitivity
-96 dBm (BLE mode)
Antenna
Integrated
Current Consumption
TX only @ +4 dBm, @ 3V, DC/DC enabled
7.5 mA
TX only @ 0 dBm, @ 3V, DC/DC enabled
5.3 mA
TX only @ +4 dBm
16.6 mA
TX only @ 0 dBm
11.6 mA
RX only @ 1 Mbps @ 3V, DC/DC enabled
5.4 mA
RX only @ 1 Mbps
11.7 mA
CPU @ 64MHz from flash
7.5 mA
CPU @ 64MHz from RAM
6.7 mA
CPU @ 64MHz from flash @ 3V, DC/DC
3.7 mA
CPU @ 64MHz from flash RAM @ 3V, DC/DC
3.3 mA
System On
1.2 μA
System Off
0.7μA
Additional current for RAM retention
20 nA / 4K block
Operating conditions
Power supply
1.7~3.6V
Operating temperature
-25~+85 °C
COPYRIGHT ©2017 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Block diagram:
Pin Description of Module（Top View）:
Pin
Name
Description
Pin1
P0.23
Digital I/O
Pin2
P0.22
Digital I/O
Pin3
P0.21
Digital I/O
COPYRIGHT ©2017 ALL RIGHTS RESERVED
XunTong Tech
Note
Configurable as pin reset.
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Pin4
P0.20
Digital I/O
Pin5
SWDCLK
HW debug and flash programming I/O
Pin6
SWDIO
HW debug and flash programming I/O
Pin7
P0.19
Digital I/O
Pin8
P0.18
Digital I/O
Pin9
P0.17
Digital I/O
Pin10
P0.16
Digital I/O
Pin11
P0.15
Digital I/O
Pin12
P0.14
Digital I/O
Pin13
P0.13
Digital I/O
Pin14
P0.12
Digital I/O
Pin15
P0.11
Digital I/O
Pin16
P0.10
Digital I/O
Pin17
P0.09
Digital I/O
Pin18
P0.08
Digital I/O
Pin19
P0.07
Digital I/O
Pin20
P0.06
Digital I/O
Pin21
P0.05
Digital I/O
Pin22
P0.04
Digital I/O
Pin23
P0.03
Digital I/O
Pin24
P0.02
Digital I/O
Pin25
P0.01
Digital I/O
Pin26
P0.00
Digital I/O
Pin27
P0.31
Digital I/O
Pin28
P0.30
Digital I/O
Pin29
P0.29
Digital I/O
Pin30
P0.28
Digital I/O
Pin31
P0.27
Digital I/O
Pin32
P0.26
Digital I/O
Pin33
P0.25
Digital I/O
Pin34
VCC
Power Supply
Pin35
P0.24
Digital I/O
Pin36
GND
Ground
Note: An internal 4.7μF bulk capacitor has been included on the module. For those application that
with heavy GPIO usage and/or current draw, it is good design practice to add additional bulk
capacitance as required for your application.
General Purpose I/O:
The general purpose I/O is organized as one port enabling access and control of the 32 available
GPIO pins through one port. Each GPIO can be accessed individually with the following user
configurable features:
 Input/output direction
 Output drive strength
COPYRIGHT ©2017 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com





Internal pull-up and pull-down resistors
Wake-up from high or low level triggers on all pins
Trigger interrupt on all pins
All pins can be used by the PPI task/event system; the maximum number of pins that can be
interfaced through the PPI at the same time is limited by the number of GPIOTE channels
All pins can be individually configured to carry serial interface or quadrature demodulator
signals
Hardware RESET:
There is on-chip power-on reset circuitry, But can still be used in external reset mode, in this case,
GPIO pin P0.21 as an external hardware reset pin. In order to utilize P0.21 as a hardware reset, the
UICR registers PSELRESET[0] and PSELRESET[1] must be set alike, to the value of 0x7FFFFF15.
When P0.21 is programmed as RESET, the internal pull-up is automatically enabled.
HW debug and flash programming of Module :
The Module support the two pin Serial Wire Debug (SWD) interface and offers flexible and powerful
mechanism for non-intrusive debugging of program code. Breakpoints, single stepping, and
instruction trace capture of code execution flow are part of this support.
Pin
Flash Program interface
SWDIO
Debug and flash programming I/O
SWCLK
Debug and flash programming I/O
This is the hardware debug and flash programming of module, J-Link Lite support, please refer
www.segger.com.
PCB Footprint （Top View）:
COPYRIGHT ©2017 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com
Recommended RF Layout & Ground Plane:
The module integrated antenna requires a suitable ground plane to radiate effectively. The area
under and extending out from the antenna portion of the module should be kept clear of copper and
other metal. The module should be placed at the edge of the PCB with the antenna edge facing out.
Reducing the ground plane will reduce the effective radiated power.
Ordering Information:
Part Number
Description
PTR9618
Bluetooth Low Energy System on Module
PTR9618-EVB
Evaluation boards for module，with key, LED, I/O extend，sock
for coin cell battery.
Absolute Maximum Ratings:
Symbol
VCC_MAX
VIO_MAX
VIO_MAX
TS
Parameter
Voltage on supply pin
Voltage on GPIO pins (VCC > 3.6V)
Voltage on GPIO pins (VCC ≤ 3.6V)
Storage Temperature Range
Min.
Max.
Unit
-0.3
-0.3
-0.3
-40
3.9
3.9
VCC + 0.3V
125
°C
Important Notice:



Reserves the right to make corrections, modifications, and/or improvements to the product and/or
its specifications at any time without notice.
Assumes no liability for the user’s product and/or applications.
Products are not authorized for use in safety-critical applications, including but not limited to
life-support applications.
ATTENTION!
Electrostatic Sensitive Device
Observe Precaution for handling.
COPYRIGHT ©2017 ALL RIGHTS RESERVED
XunTong Tech
TEL: +86 755 26675941
E-mail: nrf@freqchina.com

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : MCU
Create Date                     : 2017:03:09 10:28:34+08:00
Modify Date                     : 2017:03:09 19:05:16+08:00
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : MCU
Description                     : 
Title                           : 内置协议及链路层、具有六路接收通道
Company                         : Microsoft China
Source Modified                 : D:20170309022828
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Metadata Date                   : 2017:03:09 19:05:16+08:00
Keywords                        : 
Producer                        : Adobe PDF Library 11.0
Document ID                     : uuid:1e12aff4-4d21-43a3-a0f9-cced1e6f4318
Instance ID                     : uuid:e0f3719d-fb3b-463e-b8b2-b321356fce18
Page Layout                     : OneColumn
Page Count                      : 6

EXIF Metadata provided by EXIF.tools