LB Technology 55963TR Video Baby Monitor-Camera User Manual Baby Monitor LB55963 UserManual 20181225

LB Technology Co., Ltd. Video Baby Monitor-Camera Baby Monitor LB55963 UserManual 20181225

15_LB55963T UserMan

LB55963T/RWARNINGSTRANGULATION HAZARD － Children have STRANGLED in cords. Keep this cord out of reach of children (more than 3 feet/1 meter away from the crib). Never use extension cords with AC adapters. Only use the AC Adapters provided.WARNINGAdult assembly required. Keep small parts away from children when assembling.Warning Information＊Keep this instrucon manual for future reference.＊For adult use only.WARNING·When an AC Adapter is plugged into an electrical outlet, do not the exposed end.·Test baby monitor before first use, periodically, and when changing locaon of the baby unit(Camera).·Do not use monitor near water (Such as bathtub, Sink, etc)·Keep parent unit away from heat sources (Such as stoves, radiators, etc)·Make sure there is proper venlaon around baby unit and parent unit.·This product is not a toy. Do not allow children to play with it.·The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.·The baby monitor should not be considered as a medical device. While using the baby monitor, it is strongly recommended to have an adult directly checking on your baby. Premature babies or children considered at risk must be supervised by your pediatrician or other medical staff.THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION·Use only the original rechargeable baery provided.·Do not shot-circuit supply terminals.·Remove baery when product is stored for long periods of me or when ba ery is exhausted.·Dispose of exhausted baery properly.·Keep all baeries away from children.·The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.·Danger of explosion if baery is incorrectly replaced. Replace only with the same or equivalent type.·Baeries (baery pack or baeries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.Baery WarningPrecauons·Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electrics shock.·The baby monitor works beer in temperature ranging between 0℃ and 40℃ (32℉ and 104℉)·Do not dismantle the appliance. It does not contain any parts that may be used independently.·Never Expose the baby monitor for long period to sun’s direct rays and never place it next to a source of heat, in a damp or very dusty room.·Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.·Do not aempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. ·The product should be mounted to a wall or ceiling inly as recommended by the manufacturer.This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operaon.FCC CauonTo assure connued compliance, any changes or modificaons not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecng to computer or peripheral devices).Federal Communicaon Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communica-oons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:. Reorient or relocate the receiving antenna.. Increase the separaon between the equipment and receiver.. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.. Consult the dealer or an experienced radio/TV technician for help.FCC Radiaon Exposure StatementThis equipment complies with FCC RF radiaon exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cenmeters between the radiator and your body.This transmier must not be co-located or operang in conjuncon with any other antenna or transmier.The antennas used for this transmier must be installed to provide a separaon distance of at least 20 cm from all persons and must not be co-located or operang in conjuncon with any other antenna or transmier.LBTech’s baby monitor warranty policyLBTech will repair or replace (at our opon) your unit free of charge for 12 months from the date of purchase if the unit is defecve in workmanship or materials. To claim your repair/replacement, the product must be returned to LBTech together with a copy of the purchase receipt. In the absence of the purchase receipt, the warranty will be 12 months from the date of manufacture. This warranty does not apply to normal wear or damage from misuse, abuse, improper storage and handling, installaon, accident, unauthorized repair or alteraon. Please contact our Customer service by Facebook LBTech or via email for details.Industry Canada StatementThis device complies with Industry Canada licence-exempt RSS standard. Operaon is subject to the following two condions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operaon of the device.Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitaon est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'ulisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est suscepble d'en compromere le fonconnement.IC Radiaon Exposure Statement:This equipment complies with IC RSS-102 radiaon exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Cet équipement est conforme aux CNR-102 d'Industrie Canada. Cet équipement doit êtreinstallé et ulisé avec une distance minimale de 20 cenmètres entre le radiateur et votrecorps. Cet émeeur ne doit pas être co-localisées ou opérant en conjonc on avec autreantenne ou émeeur. Les antennes ulisées pour cet émeeur doivent être installés eournir une distance de séparaon d'au moins 20 cenmètre de toute personne et doit pas être co-située ni fonconner en onjoncon avec une autre antenne ou émeeur.1 meterNever place the baby unit or the cord within 1 meter of the crib.Connect the small plug of the power adapter to the Baby Unit and the other end to a suitable electrical outlet. Only use the enclosed adapter (5V DC 1000mA).Press and hold “ ” buon ll green power LED is turned on to turn on baby unit. Connecng the power supply for the Parent Unit.Connect the small plug of the power adapter to the parent unit and the other end to a electrical outlet. Only use the enclosed adapter (5V DC/1000mA).Recommend charging me of at least 3 hours before first use.13 42Setup and use your digital video baby monitorB.C.When baery is low, the power on off LED (icon) will flash red and on screen If you use the parent unit for the first time, when you turn on the parent unit, some boot menus Notice:will pop-up on the screen, we try to explation status and function on these menus, please according to the tips to switch to the monitor system interface. When you are fimaliar with this monitor, you could switch off these on screen tips in menu.display baery icon will flash red indicang that the baery needs to be charged.Precaution: use of battery for Parent UnitOnly charge the battery when the battery life indicator is low. Constant recharging of your battery before the low battery indicator light comes on will decrease the life of your batteries.Installing Baby UnitA. Place Baby Unit on a flat surface, such as a desk or shelf or mount the camera on a wall.Function of keys and LED indicators Start to use monitorParent Unit Status barMenu operationBaby UnitPower Press and hold ll power LED is turned on to turn on baby unit. Short press to turn off baby unit. When camera is powered on, press and hold ll power LED starng to blink.Kick StandFlip out the kick stand and place the Parent Unit on a stable, level surface.AntennaMicrophoneLoudspeakerUSB port:Camera AntennaRoom Temperature sensor: Gather room temperature informaon.Power/Pairing Power LED buttonBattery DoorOpen the baery door to change baery.AntennaHW ResetUSB portLi up antenna to have beer recepon of audio and video.Short press to turn off the parant unit, and need to restart.Press to switch on/off Power Saving (voice acvaon mode).Menu mode (Press to adjust menu sengs)Press to decrease and increase volume.Menu mode (Press to select menu option)Menu mode (Press to adjust menu sengs)Press and hold to talk to baby unit.LoudspeakerVolume down/upTalkUp/DownLeft/RightSelectPower Saving-on/offSignal strength referenceCamera numberBaby room temperatureBaery levelTalk funcon is acvatedZoom in is acvatedMonitor is mutedTemperature alert is acvatedScan view is acvatedAdjust Parent Unit LCD Brightness lighter or darker.Adjust camera volume : Soundlevel from 1 to 5.ADD: Add addional camera.Delete: Delete paired camera from the list.SCAN: Display paired camera one by one.View: Select and display the camera.Quiet : Baby cry a lile bit to acvate the Parent Unit.AutoAcvaon sound level selecon in power saving mode.: Learning environment sound and acvaon. Recommend for users having white noise machine, fans and lulllabies near by.Medium: Baby cry moderate to acvate the Parent Unit.LoudSound Bar : Baby cry louder to acvate the Parent Unit.Audio on or off opon in power saving mode: Keep audio connuouslyon or OFF when screen is off in power saving mode.: This sound bar is disigned for deaf parents to reflect soundlevel picked up from camera. You can turn visual sound level indicaon on or off.boot menu. You can turn the explanaon on or off based on your usage. High: Beep Alarm is issued when room temperature is higher than this seng.Low: Beep Alarm is issued when room temperature is lower than this seing.C: Display temperature in Celsius scale.FTemperature calibraon: Display temperature in Fahrenheit scale.ON: Acvate room temperature alarm funcon.OFF : Deacvate room temperature alarm funcon.: calibrate room temperature display to your standardized one.Step 1: Move the parent unit to the same area as the camera. Both parent and baby unit are switched on.Step 2: Select ADD in Menu. The next available camera will automacally be highlighted. Press “Select” to begin pairing.Step 3: Within 10 seconds, press “Pairing buon” of camera. Step 4: Once successfully paired, the camera light will stop flashing and video will appear on the monitor screen within 20 seconds.Baby’s crying sound levelTo acvate Parent unit from Power saving modeOutInZoomPairing buttonCAM12 3 CINSTRUCTION MANUAL PAIRVOL- VOL+VOX23 C CAM1oExplanaon On/Off : We try to explaon status and funcon on the Power on off status LEDSteady Green: Parent Unit is powered on. Steady Orange: Charging baery.Flash Red: Baery LowPower Saving on off status Steady Green: Power saving mode is acvated. Sound Level indicatorVisual indicator for sound picked up from baby unit. The louder the sound is from Baby unit, the more Power Saving-on/off modeScreen is switched off to save baery Press and hold to switch “On/Off” the unit.energy. When baby cry loud enough, screen is switched on to display baby’s video. Baby cry level is adjustable from Menu seng (Sensivity Level L, M, H, AUTO).Short cut to switch camera viewMENUMicrophonePowerPress this key to view camera 1, camera 2 and etc. paired camera. Press to open and exit menu opons.LEDs are light on.OKCAMResetVOL-VOL+TAL KTAL KMENUCAMVOXPOWERVOL-VOL+TAL K MENUCAMVOXPOWERUSB CHARGINGVideo Baby Monitor-Camera LB55963TVideo Baby Monitor-Monitor LB55963R

Navigation menu