LEON SPECIALTY 71002100 Smart Lock User Manual
LEON SPECIALTY INC. Smart Lock Users Manual
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3146584 |
| Application ID | VjZVZO1jfn9JMha4IhyiTA== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 100.29kB (1253575 bits) |
| Date Submitted | 2016-09-26 00:00:00 |
| Date Available | 2016-09-30 00:00:00 |
| Creation Date | 2016-08-23 14:20:15 |
| Producing Software | Adobe PDF Library 15.0 |
| Document Lastmod | 2016-08-23 14:20:23 |
| Document Title | Users Manual |
| Document Creator | Adobe InDesign CC 2015 (Windows) |
cover page USER MANUAL PL7100 RS2100 TABLE OF CONTENTS Parts List - Exterior Technical Specifications 11 Parts List - Interior Troubleshooting 12 Compatible cards and phones Disclaimer 13 Phone Operations Bluetooth Unlocking Touchpad Operations Programming Codes using Touchpad VARICODE Unlocking Lock-out Events, Beeps and LED 10 REGULATORY COMPLIANCE The device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC WARNING STATEMENT You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. PARTS LIST - EXTERIOR PL7100 STATUS LED SENSOR AREA and TOUCHPAD KEYWAY RS2100 STATUS LED SENSOR AREA and TOUCHPAD KEYWAY PL7100 / RS2100 PARTS LIST - INTERIOR SETUP BUTTON 1. PL7100 RS2100 SETUP BUTTON Introduction PL7100 and RS2100 are smart locks with Bluetooth LE, NFC, MiFARE RFID, and Touchpad capabilities. PL7100 / RS2100 2. Compatible cards and phones 2.1 RFID Cards / Key Fobs • Support MiFARE Classic, MiFARE Ultralight, MiFARE DesFire, or ISO/IEC 14443 type A with fixed UID. 2.2 Phones • iPhone 4S or above with iOS 8.0 or above • Android 4.3 or above with Bluetooth Low Energy capability. NFC capability is required for using the NFC feature. 3. Phone App 4. Download K3 Connect on App Store or Google Play, and register an account. For Android users, if NFC is available, use K3 Connect+ instead of K3 Connect. Always update the App to the latest version. Management 4.1 By Phone A compatible phone with K3 app installed can be used as the Admin of Locks. Management tasks can be performed in the App. An Admin can manage multiple Locks, but a Lock can only have one Admin at a time. A phone can be an Admin of a lock(s) and client of other lock(s) at the same time. PL7100 / RS2100 4.2 By Touchpad If Admin phone is not available, the Touchpad can also be used for selected management tasks. See later section for the full specification. 5. Phone Operations 5.1 Pairing to Become the Admin a. In the K3 Connect app, press the “+” on the top-right corner of the Locks page. b. Fill-in the DIN (pl7100 or rs2100 respectively) and your selected Lock name, then confirm and put the phone close to the Lock (within 1 meter). c. Push the setup button. d. Follow the UI (you may be prompted to setup Wi-Fi SSID/password to connect this Lock to your Wi-Fi and Internet; ignore it for now if Gateway is not available). This is an optional device that allows a phone to unlock the Lock using the Bluetooth Gateway option via Wi-Fi remotely. e. After successfully Pairing, the phone is now the Admin of the Lock. 5.2 Unlocking An Admin or Client can unlock in different ways: a. Bluetooth Manual Unlocking • Open the K3 Connect app. • In the Locks page, click on the tab of your Lock name to trigger it. PL7100 / RS2100 b. Bluetooth Auto Unlocking To set up the Auto Unlocking feature, open the K3 Connect app. In the Locks page, Select which Lock you wish to set up and slide left on the tab. Press “Info” and navigate to the menu to enable the Auto Unlocking features. There are 2 kinds of Auto Unlocking: trigger by touch, or trigger by location. See the App UI for more description. c. NFC Unlocking With the K3 Connect+ App installed, Admin and Client phones can unlock with NFC by waking up the phone and tapping it on the sensor/ touchpad of the lock. 5.3 Admin phone options The App can do the following management tasks (as Admin): • Set Names of Locks • Lock parameters setting (such as Passage Mode or Mute) • Add/Delete Clients (including other phones, cards, or CODEs) • Set Client access rights (such as limited duration or only one-time access or temporarily suspended) • Set Client Nick-names • Generate VARICODE • View Audit Trail • Check Lock Battery status • Update Lock Firmware PL7100 / RS2100 6. Touchpad Operations 6.1 Wake up Before any touchpad operations, touch the Lock sensor to wake it up. 6.2 Setting the Master Code (MC) THE FACTORY DEFAULT MASTER CODE IS 12341234 MC length is between 6 to 12 digits. Follow these steps to change the Maste Code: 1. Press the Setup Button 2. Wake up touchpad 3. Enter the new MC followed by # 4. Enter the new MC again and followed by # 6.3 Programming Codes using the Touchpad 1. Add Code (new CODE length is between 6 to 12 digits) MC + # + 1 + 1 + 2. NEW CODE + # + NEW CODE + # Add RFID Card / Key Fob MC + # + 1 + 2 + TAP CARD OR KEY FOB PL7100 / RS2100 3. Delete CODE MC + # + 2 + 1 + 4. + # + CODE + # Delete RFID Card / Key Fob MC + # + 2 + 2 + 5. CODE TAP CARD OR KEY FOB Delete All Codes (exclude Master Code) MC + # + 3 + 1 6. Delete All RFID Cards / Key Fobs MC + # + 3 + 2 7. Delete All Phones including Admin MC + # + 3 + 3 8. Delete All Codes/Cards/Key Fobs/Phones including Admin MC + # + 3 + 4 PL7100 / RS2100 6.4 CODE Unlocking Wake-up touchpad, enter CODE followed by # 6.5 VARICODE Unlocking • VARICODE is a time-specific temporary code that can be generated in the App. VARICODE can be generated in the App anywhere; no need to be in front of the Lock. • VARICODE can be obtained in the App: In the Clients page, press the “+” on the top-right corner, and select Type as VARICODE to see the UI. Once generated, send the VARICODE to the users. • For VARICODE Unlocking: Wake-up keypad, enter #, enter VARICODE 7. 8. Unlocking by RFID Card / Key Fob Tap the card/key fob in front of the sensor/touchpad, and wait until the LED flashes and you hear a sequence of beeps. Low Battery Warning There are two indicators when the batteries are running low: • When successfully unlocked, you will hear 3 beeps then 5 beeps for low battery warning. • If the batteries are too low, it will not unlock even after successful authentication using a registered RFID/Key Fob/Phone or correct CODE, and you will hear 3 beeps then 10 beeps as warning. **Both indicators will only stop once the batteries are replaced with new ones. PL7100 / RS2100 9. Lock-out After 3 consecutive unsuccessful unlocking attempts, the Lock will be non-responsive for 1 minute. 10. Reset to Factory Default 11. Events, Beeps and LED To reset to factory default, follow these steps: 1. Remove battery cover and take one battery out. 2. Press and hold setup button and replace the battery. 3. Wait until you hear 4 beeps and then release the setup button. All previous created users and Admin will be deleted. 4. Replace the battery cover. Events Beeps LED Setup Button Pressed 2 short beeps Exit Setup Mode 2 short and 1 long beeps During Setup Mode Pairing Success 4 beeps ascending tone Pairing Fail 1 long and 4 short beeps, the long beep tone is higher Green flash 1x Green flash 1x Red light ON Green flash 1x Red flash 1x PL7100 / RS2100 Events Beeps LED Successful Unlocking 3 beeps ascending tone Access Denied 1 long and 4 short beeps, the long beep tone is higher Low Battery Successful Unlocking 3 ascending tone beep followed by 5 short beeps Successful Authentication but does not unlock due to extreme low battery 3 ascending tone beep followed by 10 short beeps Successful Menu Operation 4 beeps, ascending tone Failed Menu Operation 1 long and 4 short beeps, the long beep tone is higher Red flash 1x Lock-out 1 long and 4 short beeps, followed by another long beep Red long flash 1x During lock-out period Red flash 2x every 5 seconds (for 1 minute) After successful unlocking, before relocking Green flash once per second Relocking Green flash 1x Red flash 1x Green flash 1x Red short flashes 5x Green flash 1x Red short flashes 10x Green flash 1x Red flash 1x 10 PL7100 / RS2100 12. Technical Specifications • User Counts: maximum 1 Admin + 49 Client Phones, 50 Codes, and 50 Cards • Powered by 4x AA Batteries • Operation Temperature: -20°C to 70°C • Radio Frequency: NFC/MiFARE: 13.56MHz, Bluetooth: 2.4GHz 13. Troubleshooting PROBLEM Administrator phone becomes an invalid user SOLUTION The Admin may lose the administration rights when any of the following happens: 1. Another Phone has been setup as a new Admin 2. Operation of “Deleted All Phones” or “Delete All Codes/ Cards/Phones including Admin” are performed on keypad 3. Phone is reset-to-factory-default Lock is working but no audible sound Check if parameter setting is on Mute mode 11 PL7100 / RS2100 PROBLEM SOLUTION Not relocking after being unlocked Check if parameter setting is on Passage mode Lock not responding Change battery and try again NFC unlocking is not working but other functions of the Lock is still working 1. Close the app and restart, then try again 2. If it’s still not working, turn NFC off and back on again, then try unlocking the Lock 3. If it’s still not working, reboot the phone and try again Bluetooth communication with the 1. For the App to close, then Lock not working (For Bluetooth launch the App and try again Pairing, Unlocking, or Sync) but 2. If still not working, turn-off other functions of the Lock are still Bluetooth function on the phone working and turn-on again, then try again 3. If it’s still not working, reboot the phone and try again 12 PL7100 / RS2100 DISCLAIMER: Cal-Royal Products does not claim that this lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property like any other locks. No lock can substitute for vigilance, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional. Notice of Open Source Licenses [FreeRTOS] This product uses FreeRTOS v7.3.0. The source code of FreeRTOS used can be downloaded here: http://sourceforge.net/projects/freertos/files/ [OpenSSL] This product uses OpenSSL, and the OpenSSL license can be downloaded here: http://www.openssl.org/source/license.html This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.openssl.org/) This product includes cryptographic software written by Eric Young (eay@cryptsoft.com). This product includes software written by Tim Hudson (tjh@cryptsoft.com). 13 PL7100 / RS2100 6605 Flotilla St., Commerce,CA 90040 Tel. (323) 888-6601 Fax. (323) 888-6699 Website: www.cal-royal.com E-mail: sales@cal-royal.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.6-c067 79.157747, 2015/03/30-23:40:42 Create Date : 2016:08:23 14:20:15-07:00 Metadata Date : 2016:08:23 14:20:23-07:00 Modify Date : 2016:08:23 14:20:23-07:00 Creator Tool : Adobe InDesign CC 2015 (Windows) Instance ID : uuid:0d1e8b18-43d9-4b85-a530-6321fd2103b0 Original Document ID : xmp.did:076396fc-1284-1a44-840a-b28cd279ca15 Document ID : xmp.id:385a73ab-8df7-9e49-ae3b-fbf76e25101a Rendition Class : proof:pdf History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CC 2015 (Windows) History Changed : / History When : 2016:08:23 14:20:15-07:00 Derived From Instance ID : xmp.iid:f7390967-3b52-8c4e-ba15-c8ed6c151c1a Derived From Document ID : xmp.did:076396fc-1284-1a44-840a-b28cd279ca15 Derived From Original Document ID: xmp.did:076396fc-1284-1a44-840a-b28cd279ca15 Derived From Rendition Class : default Format : application/pdf Producer : Adobe PDF Library 15.0 Trapped : False Page Count : 16 Creator : Adobe InDesign CC 2015 (Windows)EXIF Metadata provided by EXIF.tools