LG ELECTRONICS GT-8310C Cordless Phone User Manual Users Manaul

Download:
Mirror Download [FCC.gov]
Document ID	128359
Application ID	fS6Kwp7IdrQCIlZtVcoOQQ==
Document Description	Users Manaul
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Microsoft Word - pdf
Filesize	26.21kB (327681 bits)
Date Submitted	2000-12-12 00:00:00
Date Available	2000-12-08 00:00:00
Creation Date	2000-12-12 13:16:03
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2000-12-12 13:16:05
Document Title	Users Manaul

900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
OPERATION DESCRIPTION
( MODEL : GT- 8310C )
SK : TCTU0001701-MG
Iss.
DATE
’00. 07. 24
DESCRIPTION : OPERATION DESCRIPTION OF GT-8310C
SHEETS
NOTICE NO.
DESIGNER CHECKER
28
K961/26/8902
Y. H. Ji
J. H. Lee
GT-8310C (900MHz DSST WITH CALLER ID , CALLWAITING ID and ANSWERING SYSTEM) MANUAL
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
This equipment has tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC
Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measurements:
❏ Reorient or relocate the receiving antenna.
❏ Increase the separation between the equipment and receiver.
❏ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
❏ Consult the dealer or an experienced radio/TV technician for help.
! CAUTION
Changes or modification to device not expressly approved by LGE could void the user’s authority to operate
this equipment. Copyright 2000 by LGE. All rights reserved.
! Warning
This equipment will be inoperable when mains power fails.
! Important Notice
Since this equipment has very low output power (EIRP < 10mW), it complies with FCC RF Exposure
Limit.
MODEL GT-8310C
1999 LGE. No part of this publication may reproduced, transcribed, stored in a retrieval system,
or translated into any language in any form, by any means, without the written permission of LGE.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
GETTING TO KNOW YOUR NEW PHONE
Your new GT-8310C telephone gives you the ultimate in cordless telephone sound quality with the luxury of
Caller ID and Call Waiting ID
If this is your first cordless telephone, you'11 soon discover that your cordless is similar to regular telephone,
except without the cord. If you've owned a cordless in the past, you'll discover that the GT-8310C telephone is the
most powerful and full-functioned Call Waiting ID cordless telephone on the market.
Some key features are:
❍ 60 name and number Caller ID/Call Waiting ID memory
❍ 20 name and number programmable memory
❍ Hearing-aid compatibility
❍ High quality digital security communication
❍ Dual mode voice mail serviceable (FSK , STUTTER)
Unlike regular telephones, your cordless does not work during power failures.
Because of this restriction, we do not recommend you have only cordless telephone in your residence.
UNPACKING YOUR PHONE
In addition to this handbook, check that you have:
7 Foot Line Cord for Wall Mounting
D-AA600 x 3 3.6V 600mA Battery
(This might not be pre-installed in your handset)
AC Adapter
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
LOCATING KEYS, LIGHT, AND S WITCHES
ON THE B ASE
Ne
•
Tim
Alar
••
•/ •
Play
St
• Volume •
Recor
••
Rin
Progra
Eras
Pa
ger
① The PAGE key - is a homing system for finding the handset.
If you press the PAGE key once, the handset beeps for 15seconds.
② IN USE light - becomes lit when the GT-8310C is being used.
③ CHARGE light - comes on solid when the handset is in the base.
④ VOICE MAIL light – flashes slowly to alert you when you receive new messages in
your Voice mail messages mail box. MESSAGE WAITING appears on the display.
NEWCALL light – flashes more slowly when you receive new calls.
This light continues to flash until you review the newcalls
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
ON THE HANDSET
Keys
TALK key-Turns the
phone on or off so you
can dial or talk.
Voice mail key.
Directly access your
V.Mail service
12 : 22
PM
12 / 01
CALL
01
✉
1- 555 – 123 - 4567
SMITH JOHN
Dialing keys-Control
DEL
manual dialing.
▲
VM
Scroll keys
PGM
VOLUME
" #
Scrolls through your
Callers log
TALK
▼
RE/PA
2 ABC
3 DEF
4 GHI
5 JKL
6 MNO
7 PQRS
8 TUV
9 WXYZ
0 OPER
10
+1
FLASH
MEM
Redial keyRedials your last outbound call or inserts a
pause in a number
when entering
numbers into memory.
MUTE
DELETE Key- Removes records from the Callers log or from memory dialing.
MEM key-Allows you to store frequently dialed numbers and to dial directly from the speed dialing list.
FLASH key- Allows you to switch between a call and a Call Waiting call.
PGM key-Allows you to program your setting up your function or to edit a name and number in memory.
VOLUME UP/DOWN KEY- Allows you to adjust the loudness of the handset earpiece, or the ringer
or allows you to edit the character at Memory mode.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
HEADSET Jack
Allows you to add a headset to the handset (not included, but available by order.)
HEADSET JACK
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
SETTING UP YOUR PHONE
Now that you've checked the contents of the carton, it only takes a few steps
to set up your phone.
STEP 1. CHOOSE A CENTRAL LOCATION FOR THE BASE UNIT
The base should be away from all other electronic equipment such as a personal computer,
microwave, stereo ,or television. It is also a good idea to place the unit away from
noisy areas, or from heat sources such as a radiator or direct sunlight.
STEP 2. PLUG IN CORDS
You can set your GT-8310C telephone on a tabletop or you can mount the phone on a wall.
When on a tabletop, you can place the handset with either the keys facing downward or upward.
If you decide to use the wall mount position, you can also place the handset with the same-ward.
To use on a tabletop or desk:
1.Take the long telephone line cord that comes with the phone and plug one end into the
labeled TEL-LINE
2.Thread the long line cord through the channel in the housing to secure the cord.
3.Take the remaining end and plug it into the wall jack.
4.Plug the adapter tips into the adapter jack. Be sure that the tip is all the way into the jack.
5.Thread the adapter cord through the channel on the left-hand side of the bracket.
To mount on a wall:
1.Locate the handset hook. It is a small
square plastic piece located at the
bottom of the handset receiver well.
2. Slide the handset hook up and turn it
around so that the tab is the top.
3.Remove the mounting bracket from the
bottom of the phone by pressing down
on the two clips near the top.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
4. Turn the mounting bracket around
so that the larger part the wedge is
set the bottom of the phone.
5. Use the same method to replace the
bracket.
6. Insert the 8 inch line cord into phone
jack marked TEL LINE.
7. Thread the line cord through the channel
on the right-hand side of the bracket to
secure the cord.
8. Plug the adapter tip into the adapter jack.
Be sure that the tip is all the way into the
jack.
9. Thread the adapter cord through the
channel on the left-hand side of the
bracket.
10. Insert the other end of the line cord into the wall jack.
11. Align the holes in the bracket over the wall-plate posts.
12. Slide the phone down until the phone is secure.
STEP 3. PLUG IN THE ADAPTER
Plug the adapter into an electrical outlet. Without AC power, your phone does not operate.
STEP 4. ADD THE BATTERY TO THE HANDSET
Use this procedure to install or to replace a "dead" battery.
! CAUTION
Use only nickel-cadium(Ni-Cad)battery in the phone.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
1. Press down on the battery cover and slide
the battery cover down to expose the
battery well.
2. Locate the battery connectors inside the
battery well.
If you are replacing a dead battery, remove
the old battery by pulling firmly on the
battery cords.
3. Insert the battery plug into the connector.
It is polarized and only insert in one
direction.
4. Place the battery in the battery well.
5. Replace the battery door.
STEP 5. TURN THE HANDSET ON
You MUST install the battery on the handset to turn on and use your phone.
1. Check the power is on and appears on the display
2. You'll hear the handset's ready tones
READY
and the 'READY' message appears on the display.
STEP 6. CHARGE THE HANDSET
Before you use the phone for the first time, you need to charge the battery
for at least 6 hours.
Place the handset in the base of the phone. The charge light the base then comes on.
Whenever you need to charge your handset, you hear short beeps and see the 'LOW BATTERY'
message. Press TALK and listen for dial tone to test for a fully charged handset.
STEP 7. Beginning the programming Sequence
SETUP PROGRAM
Most of the programming options appear in one screens.
Press PGM key, SETUP PROGRAM appears on the screen.
When you make a selection, the check mark, “✓
✓ ” moves to the selection you have made to use ▲ or ▼ key.
After making a selection, the next programming screens appear. If you make a mistake, press ← (review) key to
go back to the previous prompt or start the programming sequence again.
When you do not want to go on programming sequence, press PGM to save the previous items and you will
exit the programming mode.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
To begin the programming sequence, press PGM keys and SETUP PROGRAM appears on the screen.
STEP 8. Setting area code
Many regions are changing how customers use their area codes. In order to dial from
your call records and directory records, the GT8110C needs to distinguish between local and long distance numbers.
€ If your region has seven digit dialing (you don't need to dial your area code when
making a local call), enter your local area code as described in to set your local
area code below.
€ If your region requires that you always dial ten digits when making local calls,
also follow the procedure under to set other local area codes.
If you are unsure on how your region works, please contact your local telephone co.
TO ENTER AN AREA CODE, use the keypad. If you make a mistake, retype the area code.
8-1 To set your local area code
If you set your area code, the GT-8110C telephone removes the area code from a call
record within your own area. You need to program the code in order to dial with call records.
1. Press " PGM " key
2. Press → (REVIEW) key.
The my area code screen display.
MY AREA CODE
3. Press ▲ or ▼ key to enter your area code.
The numbers appear on the display as you press the dial keys.
If you make a mistake, press "DEL"key, and reenter the area code.
STEP 9. SET LOCAL CODE (1~6)
If your region requires that you dial ten digits when making local calls,
follow the procedure under to set other local area codes.
1. Press → (REVIEW) key
2. Press ▲ or ▼ key to enter your area code.
The numbers appear on the display as you press the dial keys.
If you make a mistake, press "DEL"key, and reenter the local code.
3. Press → (REVIEW) key
4. enter 2nd local code
GT-8110C has 6 local codes. Repeate 1~4 commands to enter other local codes.
LOCAL CODE 1
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
STEP 10. SELECTING YOUR LANGUAGE
You can choose between two different languages, English or Spanish.
The screen SELECT LANGUAGE appears
1. Press → (REVIEW) key
2. Press ▲ or ▼ key to set SELECT LANGUAGE
SELECT LANGUAGE
✓ ENG ESP FRE
to ENG or ESP or FRE .
STEP 11. Adding More units
If you subscribe to call waiting ID and this is first call waiting ID unit (the display appears as 1’ST CWID UNIT?)
you must select "YES" However, if you already have a call waiting ID unit, you must select "NO".
If you do not program this option correctly, you might not receive call waiting ID records consistently.
1. Press → (REVIEW) key
1ST CWID UNIT?
2. Press ▲ or ▼ key to set 1’ST CWID UNIT to YES or NO.
✓ YES NO
STEP 12. Turning on Callwaiting ID
If you subscribe to CALL WAITING ID, turn this position ON
1. Press → (REVIEW) key
CALL WAITING ID
✓ ON
OFF
2. Press ▲ or ▼ key to set CALL WAITING ID to ON or OFF.
Setting this feature does not subscribe or cancel CALL WAITING ID service. You must contact your local
telephone company to request a change in services.
STEP 13. ANSWER PHONE WHEN PICKED UP
There are two ways that the GT8110C can answer a call. The GT8110C can instantly answer incoming calls
when you remove it from the cradle, or the phone can be set to answer after pressing the TALK key.
1. Press → (REVIEW) key
AUTO ANSWER
✓ ON OFF
2.
Press ▲ or ▼ key to set AUOT ANSWER to ON or OFF.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
If you set AUTO ANSWER to ON, GT8110C automatically answer incoming calls when removed from the
cradle
and
If
set
you
also
AUTO
you
could
ANSWER
to
press
OFF,
press
any
only
key
TALK
to
connect
key
before
after
answering
incoming
incoming
STEP 14. SET RING ON or OFF
If you don't need to hear the ring sound and select RING ON or OFF
1. Press → (REVIEW) key
RING
✓ ON OFF
3.
Press ▲ or ▼ key to set RING to ON or OFF.
STEP 15. ADJUSTING THE CONTRAST
1. Press → (REVIEW) key
2.
To lighten the display, press ▲ key while also pressing
CONTRAST
▲ key repeatedly until you get the desired results.
To darken the display, press ▼ key while also pressing ▼ key repeatedly until you get the desired results.
STEP 16. COMPLETED SETUP
Once you have finished installing your GT8110C,
SETUP COMPLETE
Your phone appears “READY” on the screen
STEP 17. SELECTING TONE/PUSE (T/P SWITCH) DIALING
☛ If your home is equipped with touch-tone dialing service, set the T/P switch T(TONE) on the base.
☛ If you only have rotary(pulse) dialing service, set the T/P switch P(PULSE) on the base.
calls
calls.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
USING YOUR PHONE
You can make calls many different ways with the GT-8310C.
DIALING (HAND SET)
1. Press TALK key on the handset.
2. Use the number pad to dial the phone number.
The phone number appears on the display as you enter the number.
You also hear beeps for each digit as you dial.
3.
Listen for a connection.
4.
Press TALK to end your call.
REDIALING
Redial is a really fast method of calling your last number. Redial dials the last number
you called whether you dialed it manually, or it was from a Call Record or the memory list.
For more information on dialing from call records, See Dialing From Call Records on page 17.
Redial is two-ways with the GT-8310C
☛ 1’ST method: Press TALK and press RE/PA
☛ 2’nd method: Press RE/PA key, your phone is automatically connected and redialed
USING SPEED DIALING(H/S)
Another short cut for dialing is using speed dialing. First, create a speed dial list,
as described in Creating Speed Dialing List on page 14. Then:
1. Press MEMO key. It displays " DIRECTORY "
2.
Press
DIRECTORY
← or → key
and it displays " NAME and NUMBER " in MEMEORY
4. Press TALK to dial
The phone automatically dials out whatever is shown on the display.
01
5556667777
SMITH JOHN
USING FLASH
To access your custom calling services, like Call Waiting, while you are on the telephone,
press FLASH key.
USING PAUSE
If you want to add a three-second pause to number in your speed dialing list, press RE/PA key while creating the
speed dial entry. For example, if you had a memory location dedicated to your voice mailbox, you might want
add a pause in a dialing string for your PIN number. For more information about programming speed dialing
numbers, see Creating a speed Dialing List on page 14.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
FINDING CLEAR RECEPTION
Your GT8320C automatically selects 1 of 20 channels at the beginning of the call for the best reception.
REACHING MAXIMUM RANGE
The GT8310C handset and base communicate up to a certain maximum range.
Weather, power lines, or other cordless telephones can affect this distance.
The GT8310C beeps whenever you are on the phone and the handset moves out of range from the base.
If you do not move back within range in 30 seconds, you lose your connection.
CREATING A SPEED DIALING LIST(H/S)
In addition to your Call Records, you can store up to 20 speed dial names and numbers in memory.
You can either enter name and number, or you can transfer a Call Record into your speed-dialing list.
MANUAL METHOD
1. Press “ MEMO “ KEY at the 'READY' message.
2.
Press " PGM " key to edit a character and number.
3.
It displays like this.
DIRECTORY
The cursor is blinking on the name field.
4.
Enter the name, character by character. You can have up to 21 characters in the name field,(The 3'rd Line)
DIRECTORY ADRESS
01
NUMBER FIELD
555–5555
NAME FIELD
SMITH JOHN
a. Locate the character on the dialing keys 2 through 9.
b.
Press once to enter the first character, twice for the second character, etc. For example, to choose a P,
press PQRS7 once, but to select an S, press PQRS7 four times.
c. Use the
Use the
← or → (REVIEW) Keys to move back and forth through the name.
$ or % keys to move up and down.
d.
Create a space between names or words, by pressing the → (REVIEW) key twice after the last character.
e.
Special
You can also use the
Symbols
key to get the following symbols in the name field:
&➯’➯(➯)➯.➯1
5. Enter the telephone number, area code first, using the dialing key pad. (2'nd Line number field)
You can have up to 32 digits in the number field,
If you make a mistake entering the telephone number, you must:
a. Press PGM key to leave speed dialing list.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
b. Press PGM key to enter the speed dialing list again.
c. Or, Use the
← or → (REVIEW) keys to find the digit and press DEL key
and re-enter the telephone number and the name.
NUMBER STORED
6. Press MEMO key to store the complete record. The phone gives you a
confirmation tone to let you know that the record is stored.
CALLER ID METHOD
A quick way to add to your speed dial list is to copy a Caller ID Call Record.
At THE 'READY' screen:
1.
Locate
using
the
Call
Record
that
you/ 25 CALLwant
10 : 35 PM 10
25
← or → (REVIEW) keys.
2.
Press
to
copy
555–5555
key
MEMO
You
SMITH
now JOHN
see
some
of
the
information from the Call Record
and
displays
"NUMBER
STORED"
and displays call record again.
NUMBER STORED
3. The number of the memory location automatically is entered.
DELETING SPEED DIALING NUMBERS
You can erase unwanted speed dial numbers one-at-a-time.
1. Press MEMO key to see your speed dial list.
2. Use
← or → key to find the memory location you want.
3. Press DEL key once, and the GT-8310C asks if you want to delete this entry.
05
18886665555
DELETE ?
4. Press DEL key again to delete the speed dial number.
The GT-8310C clears the number, gives you a confirmation beep
If you do not wish to delete the number, press MEMO key to cancel.
ADJUSTING THE HANDSET VOLUME
1. Press TALK key
2. Press
the
▲
or
▼
key
to
increase
The handset sounds an error tone when it reaches the upper or lower limits.
ADJUSTING HANDSET RINGER VOLUME
or
decrease
the
VOLUME.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
Press
the
▲
or
▼
key
on
the
handset
while
the
phone
is
not
in-use.
the
phone
is
not
in-use.
You hear the sound of the ringer as you adjust the volume between the two levels.
ADJUSTING BASESET RINGER VOLUME
Press
the
▲
or
▼
key
on
the
baseset
You hear the sound of the ringer as you adjust the volume
USER SLECTABLE RINGER TONES(H/S)
There are four user-selectable ringer tones available for this handset.
1. While in the Stand-by mode, press the FLASH button
2. Press a key (1 to 4) to select a ringer tone mode.
USER SLECTABLE RINGER TONES(B/S)
There are five user-selectable ringer tones available for this baseset.
1. While in the Stand-by mode, press the RING button.
2. Press the RING button (continuously) to select a ringer tone mode.
while
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
THE INTEGRATED ANSWERING DEVICE
TURING THE ANSWERING SYSTEM ON/OFF
1. To turn the answering system on, Press OUT DOOR. A tone sounds. Then, the OUT DOOR button is lighted.
2. To turn the answering system off, Press OUT DOOR again, Then, light turns off.
SETTING THE CLOCK
To set the correct time:
1. Press PROGRAM button.
2. Press TIME button
1. Press |•• or ••| key until you input the correct day.
1 : Sunday
2 : Monday
3 : Tuesday
4 : Wednesday
5 : Thursday
6 : Friday
7 : Saturday
2. Press |•• or ••| key until you input the correct hour(0 ~ 23).
3. Press |•• or ••| key until you input the correct minute(0~59).
3. Press PROGRAM key.
Then, the GT-8310C Answering System announces the correct time.
To listen to current time, press TIME button.
Then, answering system announces the current time.
SETTING ALARM TIME
If you set alarm time, GT-8310C sounds a alarm at your setting time in everyday.
4. Press PROGRAM button.
5. Press ALARM button.
6. Press |•• or ••| keys until you input the correct hour(0 ~ 23).
7. Press |•• or ••| keys until you input the correct minute(0~59).
8. Press PROGRAM key.
The system announces your setting time.
If you want alarm function to set, press ALARM button in stand-by mode. Alarm LED is lighted in baseset.
If you want alarm function to release, press ALARM button again. Alarm LED is OFF.
RECORDING YOUR OUTGOING MESSAGE
When you receive a call, the answering system automatically plays either a preset greeting, or your own personal greeting.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
Preset Message
The following message is pre-recorded
“Hello, I cannot receive your call, Please leave your message after a beep. Thank you.”
Recording your personal Outgoing Message(OGM)
1. Press RECORD key in stand-by mode.
The answering system announces explanation and LED counts recording time.
Record your message. (MAX 20 sec)
3. When you finish recording your message, Press •/•(play/stop) button.
A tone sounds. Your message plays back for your review.
CHOICE BETWEEN THE PRE-RECORDED GREETING AND YOUR PERSONAL GREETING
1. Press OUT DOOR button. The answering system announce choosing OGM.
2. To choose your personal outgoing message, press |•• button.
To choose pre-recorded outgoing message, press ••| button
The answering system announces your selecting OGM.
SETTING THE RING TIME
1. Press PROGRAM button
2. Press RECORD button
3. Press |•• or ••| button until you input correct ring time.(2~9)
TOLL SAVE
In the TOLL SAVE is ON, if you have new messages, the answering system answers after one ring.
If there are no new messages, the system answers after four rings. This way, when you call long distance to check your
messages, and have no message, you can hang up after the second ring to save a charge.
SETTING A PIN CODE
To listen to your messages from a remote location, you will need to enter a four digit Personal Identification Number(PIN)
code(0000 ~ 9999).
1. Press PROGRAM button.
2. Press OUT DOOR button.
3. Press |•• or ••| button until you input correct PIN code (1-digit)
4. Press PROGRAM key.
5. Repeat 3 and 4 commands until you can input 4 digits PIN code
6. Your PIN code plays back for your review.
PLAYING YOUR MESSAGES
The base 7-segment LED displays the total number of messages.
1.press •/•(play/stop)
The system announces messages.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
2. After reviewing our new messages, you can review your old messages.
Press •/•(play/stop) and |•• or ••| to review old messages.
SKIPPING A MESSAGE
1. Press •/•(play/stop) to review your messages.
2. Press ••| at anytime to skip to the next message.
3. Press •/•(play/stop) at any time to stop reviewing your messages and return to stand-by mode.
DELETING MESSAGES
1. Press •/•(play/stop) to review your messages.
2. If you decide to delete a message, press ERASE button. The system goes to the next message.
To delete all your messages, press ERASE button and press ERASE button again to confirm in stand-by mode.
REMOTE ACCESS AWAY FROM HOME
You can access functions such as checking recorded messages, playing or deleting messages, and room monitoring remotely
using a touch-tone phone.
1. Call your telephone number.
2. While the outgoing message is playing, press # button, and press your PIN code.
3. You select a command from the following chart :.
Delete all messages
0 then 0 (confirm)
then 5 (cancel)
Play
Room Monitor
Stop
Delete (while announcing)
Remote control off
When you select Room Monitor, it is continuous about 10 second.
When you are finished, The answering system automatically returns to stand-by mode.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
USING CALLER ID AND CALL WAITING ID
One of the best features of your phone is Caller ID, which allows you to see information about an incoming call
before you pick up the phone. With Caller ID service from your local telephone company,
the GT-8310C telephone displays and records information about the call in a log.
Possibly even better than Caller ID is Call Waiting ID. In addition to providing normal Caller ID information,
Call Waiting ID allows you to see caller information while you are on a call.
Now you can have the information you need to choose whether or not to answer a waiting call.
Before you use these features on your GT-8320C telephone, you must first subscribe to the services through
your local telephone company, and set "CALL WAITING ID ON or OFF" correctly during the
SETTING UP YOUR PHONE procedure.
For more details on CALLWAITING ID ON/OFF, see STEP 10. Turning on Callwaiting ID on page 11.
RECEIVING NEW CALLS
When you receive a new call, the information is stored under CALLER area.
When you press
← or → (REVIEW) key , it tells you:
❍ How many total calls you have.
❍ How many new calls you have since you
last reviewed your calls.
ALL : 23 NEW : 03
When you receive a call, the GT-8310C displays the caller information sent by the Telephone Company,
called a Call Record.
The call record consists of the following information:
❍ The caller's name( If available )
❍ The caller's telephone number
❍ The time and date of the call
❍ A call record number
10 : 35 PM 10 / 25
NEW
25
CALL
555–5555
SMITH JOHN
❍ NEW CALL LCD display
❍ MESSAGE WAITING (VOICE MAIL) indicator
✉
MESSAGE WAITING
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
REVIEWING CALL RECORDS
To review a call Record:
1. Press
← or → (REVIEW) to see how many new calls you have.
← or → (REVIEW) key to move though the Call Record list.
2. Use
→ (REVIEW) key to see the most recent call record.
☛ Press ← (REVIEW) key to see earlier calls.
☛ Press
When you reach either end of the Call Record
list, you see an 'END OF LIST' message. If you
continue to press ← or → (REVIEW) key,
END OF LIST
you scroll through the list again.
DIALING FROM CALL RECORDS
You can use your Call Records as a short-cut method of dialing.
1. Press
2. Use
← or → (REVIEW) key to see your Call Records.
← or → (REVIEW) key to find the desired Call Record.
3. Press TALK key
The phone dials whatever is shown on the display.
SAVING CALL RECORDS
Your phone stores up to 60 Call Records before the memory becomes full.
When the next call comes in, the oldest record drops off and makes room for the new Call Records.
To save specific calls, delete old and unnecessary call records to keep from filling your phone's memory.
DELETING CALL RECORDS
You can either delete a single record or you can delete all Call Records at one time.
To delete a single record:
← or → (REVIEW) key to see your Call Records.
2. Use ← or → (REVIEW) key to find the desired Call Record.
1. Press to
3. Press DEL key once, and the GT-8310C asks if you want to erase this Call Record.
4. Press DEL key again to erase the Call Record.
The GT-8310C deletes the Call Record, gives you
a confirmation beep,
10 : 35 PM 10 / 25 CALL 25
555–5555
DELETE ?
If you do not wish to delete the Call Record, press
← or → (REVIEW) key to cancel.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
To delete all Call Records:
1. Press
← or → (REVIEW) key.
The display shows you how
many call records you have.
2.
Press
DEL
key
and
ALL : 23 NEW : 03
the
GT-8310C
asks
if
you want to delete all Call Records.
3.
Press
DEL
key
again
and
the
GT-8310C
clears
all Call Records,
gives
you
DELETEconfirmation
A LL ?
beep.
SEEING LONG RECORDS
If you receive long records on caller ID information, you could see that to use the ▲ or ▼ key.
the ▲ or ▼ key allows you to scroll back and forth to see long records.
1. Press
← or → (REVIEW) key.
The display shows you long records
10 : 35 PM 10 / 25
CALL
25
⇐55566677778902
SMITH JOHN
2. Press ▲ or ▼ key to see remain numbers
10 : 35 PM 10 / 25
CALL
25
44455566677778 ⇔
SMITH JOHN
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
VOICE MAIL
Voice Mail Service your calls when you are away from your phone or even while you are on the phone.
The indicator Light flashes whenever you have message in your mailbox. And once you have programmed
your Voice Mail key with your personal access codes, you can get your message at the touch of a button.
You must subscribe to Voice Mail Service in order for this feature on your phone.
To Program the Voice Mail Key.
Using this method, you can store up to 32 digits per key-You can program digits,
flash, pause, * or # , such as your mailbox number, your PIN, and any other additional codes that you need.
1. press MEMO key
2. press VOICEMAIL key
3. press
key
VOICE MAIL PGM
and then you will see the following display, The 2’nd line cursor(Number field) is blinking.
4. You can store digits, # , * , Flash , Pause up to 32 digits
5. press PGM key to cancel
6. Press
key
to
MEMO
store
To Use Voice Mail
Once you have programmed your Voice Mail key,
you can access your mail box by pressing # VOICE MAIL key
Not to use Voice Mail
If
you
are
not
subscribing
to
voice
telephone company and you set VOICEMAIL to
OFF
in
Set
up
Program
change your voice mail key into Speed dial key.
mode,
mail
service
from
VOICE MAIL
The
ON
GT-8310C
your
local
automatically
✓ OFF
To Program the SPEED DIAL Key.
Using this method, you can store up to 32 digits per key-You can program digits,
flash, pause, * or # , such as your mailbox number, your PIN, and any other additional codes that you need.
1. press MEMO key
2. press VOICEMAIL key
3.
press
VOICE MAIL
key
PGM
and then, you will see the following display, The 2’nd line cursor(Number field) is blinking.
You can store digits, # , * , Flash , Pause up to 32 digits
4. press PGM key to cancel
5.
Press
key
MEMO
to
To Use SPEED DIAL
Once you have programmed your SPEED DIAL key, you can access by pressing # VOICE MAIL key
store
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
READING DISPLAY MESSAGES
The GT-8310C informs you of status by displaying the following messages :
Message
Display
ALL CALLS & NEW CALLS: This message lets you know
how many call records you have, and how many of those call
records are new, In this example, you have 23 call records,
and 3 new calls.
ALL : 23 NEW : 03
CHARGING: The handset BATTERY is getting
low.
Place the handset in the base in order to recharge.
CHARGING
DELETE ALL?: You pressed the DEL key
after pressing the ← or → (REVIEW) key
DELETE ALL ?
DELETE ? : To delete a single record, You pressed DEL key
after pressing the ← or → (REVIEW) key.
10 : 35 PM 10 / 25 CALL 25
555–5555
DELETE ?
END OF LIST: You have reached the end of the call records.
Press either ← or → (REVIEW) key to see other records.
END OF LIST
INCOMPLETE DATA : The message sent is
incomplete data
This message usually indicates temporary interference.
There is no problem with the phone.
INCOMPLETE DATA
MESSAGE WAITING : The GT-8310C (base LED) flashes
✉
slowly to alert you and appears on the display
“ Message waiting “ When you receive new messages
in your mail box.
MESSAGE WAITING
NO CALLS:
There are no call records in the caller ID memory.
NO CALLS
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
Message
Display
NUMBER ONLY:
Either name service is not available in your area,
or you are subscribing to a number-only service.
PRIVATE: The caller has purposely chosen to
block his/her phone number.
TALK:
10 : 35 PM 10 / 25 CALL 25
555–5555
10 : 35 PM 10 / 25 CALL 25
PRIVATE
TALK
The handset is on and ready for you to dial.
PAGING :
PAGING
The Base is calling the handset.
as the name,
or both the name and number, might not be available from the
caller’s area.
UNAVAILABLE: The Caller ID information, such
10 : 35 PM 10 / 25 CALL 25
555–5555
UNAVAILABLE
10 : 35 PM 10 / 25 CALL 25
UNAVAILABLE
LONG DISTANCE : The message sent is a long distance call.
You might see this message alternate with other messages.
10 : 35 PM 10 / 25 CALL 25
555–5555
SMITH JOHN
10 : 35 PM 10 / 25 CALL 25
555–5555
LONG DISTANCE
LOW BATTERY :
The handset is needed to replace the cradle.
LOW BATTERY
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
Message
Display
OUT OF RANGE:
If you use the handset too far away from the base unit
during
call,
the
handset
will
alert
you OUTbyOF
audio
RANGE
warning
(when using talk) and OUT OF RANGE appears on the display.
NUMBER STORED : When you save the call records in the
directory or create a speed dialing list, you will see the display
like this.
Forwarded CALLS : The message sent is a forwarded calls.
You might see the 3 type messages alternate with other
messages.
NUMBER STORED
10 : 35 PM 10 / 25 CALL 25
555–5555
SMITH JOHN
10 : 35 PM 10 / 25 CALL 25
555–5555
CFW. UNIVERSAL
10 : 35 PM 10 / 25 CALL 25
555–5555
CFW. BUSY
10 : 35 PM 10 / 25 CALL 25
555–5555
CFW. NO ANSWER
NEW CALL: This message lets you know that you have a
NEW
New messages
READY
beeps
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
TROUBLESHOOTING
Are you having trouble with your phone?
Here are some of the most common problem areas and solutions.
SYMPTOM
CORRECTIVE ACTION
☛ Verify that the line cord is connected and secure.
No dial tone
☛ Check to see that you are not out of range to the base.
☛ Check that the AC adapter is plugged into the outlet.
☛ Check that the handset is fully charged.
☛ Check to see that the Battery is connected inside the battery compartment.
Phone doesn’t
ring
☛ Verify that the LINE CORD and AC adapter are plugged in correctly.
☛ Check that the RING ON/OFF in your set up program mode.
☛ Determine if you have too many communication devices hooked to a single line.
A communication device can be a phone, modem, or facsimile (FAX) machine.
Contact your local phone company business office for help calculating the limit for your
residence or business.
☛ Move the handset closer the base
The phone has
☛ Check to see that you are not out of range to the base.
Static or fades
☛ Check that the handset is fully charged.
In and out
☛ Verify that the CALLWAITING ID function is set correctly
Caller ID /
Call Waiting ID
See Step Turning CALLWAITNG ID ON or OFF on SETUP program
doesn’t work
☛ Check your service. Call your local phone company’s Business Office to ensure that
properly
your services are active.
☛ Check for a power outage in your home area
☛ Check the AC adapter
☛ Check that the extension phone is being used.
☛ Check whether the handset is making contact in the cradle.
Charge Light
does Not work
☛ Check the AC adapter
Be sure that the adapter is not damaged and that it is securely plugged into
a working outlet. Also check that the wall plug is not controlled by a wall switch.
Phone does not ☛ You might not have programmed your area code correctly.
dial out correctly
Please see Set up program my Area Code
when using call
records
Blank or faint
screen
☛ Check the contrast control for the display
see set up your program
☛ Check the AC adopter
Be sure that the adapter is not damaged and that it is securely plugged into a working
Outlet and the phone jack. Also check that the wall plug is not controlled by a wall
switch or a power strip.
☛ You might not have received your first call record.
900MHz DSST PHONE, CALLER ID ON CALL WAITING and ANSWERING SYSTEM.
SYMPTOM
CORRECTIVE ACTION
NO DATA
☛ Check your service. Call your local phone company to ensure that you have
Caller ID or Call Waiting ID service.
☛ Check the answering machine. Ensure that your answering machine is set to
answer after two rings.
☛ You answered the call before two rings.
☛ Check call Forwarding. Ensure that Call Forwarding is turned off.
☛ Contact your local phone company’s Service Department
If the problem continues for more than 24 hours.
Your local phone company central office may be
temporarily experiencing an overload.
INCOMPLETE DATA ☛ Call information was distorted before reaching the unit.
Normal static on the telephone line can cause a line error and an
INCOMPLETE DATA message. If this condition persists, check with your local
telephone company to ensure that there is not a problem with your phone line.
Handset does not
☛ The handset is not communicating with the base.
The handset is either turned off, out of range, or the battery needs recharging.
PAGE key does
not page
the handset
Handset does not
work
☛ Check that the AC adapter is plugged in and operating correctly.
☛ Check whether the handset is making contact in the cradle.
Charge.
☛ Check the AC adapter. Be sure that the adapter is not damaged and that
it is securely plugged into a working Outlet and the phone jack.
Also check that the wall plug is not controlled by a wall switch or a power strip.
☛ Verify that the handset is turned on
☛ place the in the cradle for several seconds.
Ensure the handset is making contact in the cradle.
☛ Recharge the battery.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2000:12:12 13:16:03
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2000:12:12 13:16:05-05:00
Page Count                      : 28

EXIF Metadata provided by EXIF.tools