LG Electronics USA 32LDA 32" LCD TV/MONITOR User Manual User s Manual H
LG Electronics USA 32" LCD TV/MONITOR User s Manual H
USERS MANUAL
Test Report No.: GETEC-E3-05-026 FCC Class B Certification APPENDIX H : USER’S MANUAL EUT Type: 32” LCD TV/Monitor FCC ID: BEJ32LDA LCD TV OWNER’S MANUAL MODELS: 26LX1D 32LX1D 26LX2D 32LX2D 32LP1D 37LP1D 42LP1D Internet Home Page : http://www.lge.com http://www.lg.ca Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. TM P/NO : 3828TUL309D (0503-REV00) Printed in Korea Warning Warning CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. U.S.A. only ----------------------------------------------COMPLIANCE: The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 Phone: 1-201-816-2000 http://www.lgusa.com --------------------------------------------------------------- Introduction Controls (Model Name: 26/32LX1D, 26/32LX2D) - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. Remote Control Sensor /Power Standby Indicator Illuminates red when the TV is in standby mode. Blinks green while the TV switched on and illuminates green when the TV is switched on. CH VOL MENU TV/ VIDEO/ TV GUIDE ON/OFF ON/OFF Button TV GUIDE Button TV/VIDEO / MENU Button VOLUME (F,G) Buttons CHANNEL (E, D) Buttons Button Introduction Connection Options (Model Name: 26LX1D/2D) - Here shown may be somewhat different from your TV. S-VIDEO VIDEO 2 VIDEO AUDIO Input CF/MD/Magicstor Slot 1 MS/MS-pro/xD/MMC/SMC/SD COMPONENT2 (VIDEO Input) DIGITAL AUDIO OUTPUT / DVI INPUT / COMPONENT1 INPUT AC IN HDMI / IEEE1394 Port CableCARDTM Slot AUDIO/VIDEO INPUT1 G-LINKTM Port VIDEO Memory Card Slot (Form m m m mode) AUDIO Slot 2 COMPONENT 2 VIDEO2 (MONO) L S-VIDEO CableCARD HDMI AC IN IEEE 1394 COMPONENT1 INPUT CABLE AUDIO INPUT RGB INPUT (PC/DTV INPUT) VIDEO INPUT PC AUDIO INPUT DVI INPUT COMPONENT1 VIDEO1 RS-232C INPUT (CONTROL/SERVICE) AUDIO L (MONO) VIDEO S-VIDEO REMOTE CONTROL DIGITAL AUDIO (OPTICAL) OUTPUT G-LINK ANTENNA RS-232C INPUT (CONTROL/SERVICE) / RGB INPUT (PC/DTV INPUT) PC AUDIO INPUT ANTENNA Input CABLE Input COMPONENT1 (VIDEO / AUDIO INPUT) REMOTE CONTROL Port * The HDMI port can receive video via High-Definition Multimedia Interface (HDMI) or the Digital Visual Interface (DVI). Note: An adapter or special cable is required to plug DVI into an HDMI port (available at home theater or computer stores). Connection Options (Model Name: 32LX1D/2D) - Here shown may be somewhat different from your TV. S-VIDEO VIDEO 2 VIDEO AUDIO Input CF/MD/Magicstor Slot 1 MS/MS-pro/xD/MMC/SMC/SD COMPONENT2 (VIDEO Input) DIGITAL AUDIO OUTPUT / DVI INPUT / COMPONENT1 INPUT AC IN G-LINKTM Port VIDEO Memory Card Slot (Form m m m mode) AUDIO Slot 2 COMPONENT 2 VIDEO2 (MONO) L S-VIDEO MONITOR OUT HDMI / IEEE1394 Port AUDIO/VIDEO INPUT1 CableCARDTM Slot CableCARD HDMI AC IN IEEE 1394 G-LINK DIGITAL AUDIO (OPTICAL) AUDIO L (MONO) VIDEO MONITOR OUT S-VIDEO OUTPUT VIDEO1 REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) DVI INPUT COMPONENT1 INPUT CABLE COMPONENT1 AUDIO INPUT ANTENNA VIDEO INPUT RS-232C INPUT (CONTROL/SERVICE) / RGB INPUT (PC/DTV INPUT) ANTENNA Input CABLE Input PC AUDIO INPUT REMOTE CONTROL Port COMPONENT1 (VIDEO / AUDIO INPUT) * The HDMI port can receive video via High-Definition Multimedia Interface (HDMI) or the Digital Visual Interface (DVI). Note: An adapter or special cable is required to plug DVI into an HDMI port (available at home theater or computer stores). Installation External Equipment Connections Antenna or Cable Connection Analog and Digital TV signals provided on antenna - Antenna or Cable Service without a Cable Box Connection. - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket ANTENNA RF Coaxial Wire (75 ohm) VHF Antenna Turn clockwise to tighten. UHF Antenna Outdoor Antenna Bronze Wire Be careful not to bend the bronze wire when connecting the antenna. Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Analog and Digital TV signals provided on cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) CABLE Turn clockwise to tighten. Analog and Digital TV signals provided on cable and antenna Bronze Wire Cable TV Wall Jack RF Coaxial Wire (75 ohm) CABLE Turn clockwise to tighten. Antenna ANTENNA RF Coaxial Wire (75 ohm) Bronze Wire • In a poor signal area to improve picture quality, purchase and install a signal amplifier. ANTENNA signal amplifier • If the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections. • If the antenna is not installed properly, contact your dealer for assistance. 21 Installation NOTE: All cables shown are not included with the TV. VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV. - Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. When connecting with an antenna 26 inch TV Back CableCARD 32, 37, 42 inch TV Back IEEE 1394 AUDIO L (MONO) VIDEO ANT IN ANT OUT MONITOR OUT S-VIDEO OUT IN S-VIDEO OUT (R) AUDIO (L) VIDEO IN CABLE VCR ANT OUT OUTPUT SWITCH COMPONENT1 AUDIO INPUT COMPONENT1 CABLE VIDEO1 (R) AUDIO (L) VIDEO OUTPUT SWITCH ANTENNA AUDIO INPUT S-VIDEO VIDEO INPUT HDMI ANT IN VIDEO INPUT VCR ANTENNA Connect the RF antenna out socket of the VCR to the Antenna socket on the set. Connect the antenna cable to the RF antenna in socket of the VCR. Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) When connecting with a RCA cable 26 inch TV Back 32, 37, 42 inch TV Back AUDIO L (MONO) VIDEO MONITOR OUT HDMI IEEE 1394 VIDEO INPUT COMPONENT1 INPUT DVI INPUT AUDIO INPUT COMPONENT1 VIDEO1 COMPONENT1 VIDEO INPUT OUTPUT DIGITAL AUDIO (OPTICAL) AUDIO L (MONO) VIDEO S-VIDEO VIDEO1 AUDIO INPUT S-VIDEO ANT IN ANT IN ANT OUT S-VIDEO OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN VCR ANT OUT VCR S-VIDEO OUT (R) AUDIO (L) VIDEO OUTPUT SWITCH IN Connect the AUDIO/VIDEO jacks between TV and VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Select Video1 input source using the TV/VIDEO button on the remote control. - If connected to IN2 (or VIDEO2), select Video2 input source. • If you have a mono VCR, connect the audio cable from the VCR to the AUDIO L/MONO jack of the set. NOTE: All cables shown are not included with the TV DVD Setup When connecting with a S-Video cable 26 inch TV Back 32, 37, 42 inch TV Back AUDIO L (MONO) VIDEO MONITOR OUT S-VIDEO HDMI IEEE 1394 VIDEO1 COMPONENT1 INPUT AUDIO INPUT DVI INPUT VIDEO INPUT VIDEO1 COMPONENT1 VIDEO INPUT AUDIO INPUT AUDIO L (MONO) VIDEO S-VIDEO OUTPUT COMPONENT1 DIGITAL AUDIO (OPTICAL) DVD DVD (R) AUDIO (L) S-VIDEO (R) AUDIO (L) Connect the S-VIDEO output of the DVD to the S-VIDEO input on the set. Connect the audio outputs of the DVD to the AUDIO input jacks on the set. Turn on the DVD player, insert a DVD. Select Video1 input source with using the TV/VIDEO button on the remote control. - If connected to IN2 (or VIDEO2), select Video 2 input source. Refer to the DVD player's manual for operating instructions. S-VIDEO When connecting with a HDMI cable 32, 37, 42 inch TV Back 26 inch TV Back CableCARD HDMI CableCARD HDMI IEEE 1394 IEEE 1394 COMPONENT1 HDMI-DVD OUPUT DVD Connect the HDMI output of the DVD to the HDMI jack on the set. Select HDMI input source with using the TV/VIDEO button on the remote control. Refer to the DVD player's manual for operating instructions. HDMI-DVD OUPUT ANTENNA AUDIO INPUT CABLE VIDEO INPUT DVD • TV can receive the video and audio signal simultaneously with using a HDMI cable. • If the DVD supports Auto HDMI function, the DVD output resolution will be automatically set to 1280x720p. • If the DVD does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the DVD to 1280x720p. When connecting with a component cable 26 inch TV Back 32, 37, 42 inch TV Back DIGITAL AUDIO (OPTICAL) AUDIO L (MONO) VIDEO MONITOR OUT S-VIDEO OUTPUT HDMI VIDEO1 IEEE 1394 VIDEO INPUT COMPONENT1 INPUT DVI INPUT AUDIO INPUT COMPONENT1 2-2 2-1 AUDIO INPUT COMPONENT1 INPUT OUTPUT VIDEO1 COMPONENT1 DIGITAL AUDIO (OPTICAL) VIDEO INPUT RGB INPUT (PC/DTV INPUT) DVI INPUT AUDIO L (MONO) VIDEO S-VIDEO RS-232C INPUT (CONTROL/SERVICE) 2-1 2-2 (R) AUDIO (L) DVD Select 2-1 or 2-2 (R) AUDIO (L) DVD , depending on your DVD connector. Connect the video outputs (Y, PB, PR) of the DVD to the COMPONENT1 VIDEO INPUT jacks on the set. 2-1 Connect the audio outputs of the DVD to the COMPONENT1 AUDIO INPUT jacks on the set. 2-2 Connect the optical audio output of the DVD to the DIGITAL AUDIO COMPONENT1 INPUT jack on the set. Turn on the DVD player, insert a DVD. Select Component 1 input source with using the TV/VIDEO button on the remote control. - If connected to COMPONENT2 input, select Component 2 input source. Refer to the DVD player's manual for operating instructions. • Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. PR Component ports on the TV PB Video output ports on DVD player Pr Pb B-Y R-Y Cb Cr PB PR • Digital Audio will not work for Component 2 input source. • Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. 25 Installation HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. When connecting with a D-sub 15 pin cable 32, 37, 42 inch TV Back 26 inch TV Back AC IN RS-232C INPUT (CONTROL/SERVICE) PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) G-LINK DVI INPUT REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) COMPONENT1 INPUT PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) (R) AUDIO (L) (R) AUDIO (L) RGB-DTV OUPUT DIGITAL AUDIO (OPTICAL) DVI INPUT COMPONENT1 INPUT VIDEO1 REMOTE CONTROL OUTPUT OUTPUT AUDIO L (MONO) VIDEO S-VIDEO G-LINK DIGITAL AUDIO (OPTICAL) AC IN RGB-DTV OUPUT Digital Set-top Box Digital Set-top Box Connect the RGB output of the digital set-top box to the RGB INPUT (PC/DTV INPUT) jack on the set. Connect the audio outputs of the set-top box to the PC AUDIO INPUT jack on the set. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select RGB-DTV input source with using the TV/VIDEO button on the remote control. Installation When connecting with a HDMI cable 32, 37, 42 inch TV Back HDMI 26 inch TV Back CableCARD CableCARD HDMI IEEE 1394 COMPONENT1 Digital Set-top Box ANTENNA AUDIO INPUT CABLE VIDEO INPUT IEEE 1394 Digital Set-top Box HDMI-DTV OUPUT HDMI-DTV OUPUT Connect the HDMI output of the digital set-top box to the HDMI jack on the set. Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) • TV can receive the video and audio signal simultaneously with using a HDMI cable. • If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will be automatically set to 1280x720p. • If the digital set-top box does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. Installation When connecting with a HDMI to DVI cable 32, 37, 42 inch TV Back 26 inch TV Back HDMI HDMI IEEE 1394 COMPONENT1 INPUT ANTENNA AUDIO INPUT VIDEO INPUT 2-1 2-2 DIGITAL AUDIO OPTICAL (R) AUDIO (L) Digital Set-top Box Select PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) 2-1 or 2-2 DVI-DTV OUTPUT COMPONENT1 INPUT 2-1 (R) AUDIO (L) RGB INPUT (PC/DTV INPUT) REMOTE CONTROL COMPONENT1 COMPONENT1 PC AUDIO INPUT DVI INPUT DVI INPUT 2-2 DIGITAL AUDIO OPTICAL AUDIO INPUT RS-232C INPUT (CONTROL/SERVICE) RS-232C INPUT (CONTROL/SERVICE) REMOTE CONTROL CABLE VIDEO1 VIDEO1 OUTPUT G-LINK MONITOR OUT S-VIDEO OUTPUT DIGITAL AUDIO (OPTICAL) VIDEO INPUT DIGITAL AUDIO (OPTICAL) G-LINK IEEE 1394 AUDIO L (MONO) VIDEO AUDIO L (MONO) VIDEO S-VIDEO DVI-DTV OUTPUT Digital Set-top Box , depending on your digital set-top box connector. Connect the DVI output of the digital set-top box to the HDMI jack on the set. 2-1 Connect the audio output of the digital set-top box to the PC AUDIO INPUT jack on the set. 2-2 Connect the optical audio output of the digital set-top box to the DIGITAL AUDIO DVI INPUT jack on the set. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. • If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is necessary. • If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box will be automatically set to 1280x720p. • If the digital set-top box does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. Installation External AV Source Setup COMPONENT 2 VIDEO Camcorder TV Side Video Game Set AUDIO Connect the AUDIO/VIDEO jacks between TV and external equipment. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). Select Video2 input source with using the TV/VIDEO button on the remote control. - If connected to VIDEO1 input, select Video1 input source. Operate the corresponding external equipment. Refer to external equipment operating guide. For connection instructions to operate the TV Guide On Screen system, see page 42~43. AUDIO (MONO) L VIDEO 2 VIDEO S-VIDEO VIDEO Digital Audio Output - Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port. 32, 37, 42 inch TV Back 26 inch TV Back DIGITAL AUDIO (OPTICAL) OUTPUT REMOTE CONTROL PC AUDIO INPUT DIGITAL AUDIO (OPTICAL) RS-232C INPUT (CONTROL/SERVICE) RGB INPUT (PC/DTV INPUT) DVI INPUT REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) DVI INPUT 1/2 COMPONENT1 INPUT VIDEO1 G-LINK OUTPUT G-LINK AUDIO L (MONO) VIDEO S-VIDEO AC IN 1/2 AC IN COMPONENT1 INPUT Connect one end of an optical cable to the TV Digital Audio Optical Output port. Connect the other end of the optical cable to the digital audio optical input on the audio equipment. See the external audio equipment instruction manual for operation. When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.(Refer to p.80) CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. Installation Monitor Out Setup (32LX1D/2D, 32/37/42LP1D only) - The TV has a special signal output capability which allows you to hook up a second TV or monitor. AUDIO L (MONO) VIDEO MONITOR OUT S-VIDEO Connect the second TV or monitor to the TV’s MONITOR OUTPUT jacks. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings. VIDEO1 COMPONENT1 VIDEO INPUT AUDIO INPUT 1/2 • Component1/2 input sources can be used for Monitor out. • When connecting with external audio equipments, such as amplifers or speakers, please turn the TV speakers off.(Refer to p.80) Second TV S-VIDEO IN (R) AUDIO (L) VIDEO CableCARDTM Setup 32, 37, 42 inch TV Back HDMI 26 inch TV Back CableCARD CableCARD HDMI IEEE 1394 IEEE 1394 COMPONENT1 AUDIO INPUT ANTENNA VIDEO INPUT CABLE - To view the premium stations Insert the CableCARDTM received from Cable Service provider to CableCARD slot of TV as shown. If the pairing information about this TV and the CableCARD is automatically displayed on the screen, contact with Cable service provider by phone. Caution: When removing the CableCARDTM, do not drop it as this may cause damage to the card. • Different card types can be used with this unit (Motorola, Scientific Atlanta, SCM, etc.). Installation PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol. When connecting with a D-sub 15 pin cable 32, 37, 42 inch TV Back 26 inch TV Back DIGITAL AUDIO (OPTICAL) OUTPUT REMOTE CONTROL PC AUDIO INPUT DIGITAL AUDIO (OPTICAL) RS-232C INPUT (CONTROL/SERVICE) RGB INPUT (PC/DTV INPUT) DVI INPUT REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) DVI INPUT COMPONENT1 INPUT G-LINK OUTPUT G-LINK COMPONENT1 INPUT PC AUDIO AUDIO RGB-PC OUPUT PC RGB-PC OUPUT Connect the RGB output of the PC to the RGB INPUT (PC/DTV INPUT) jack on the set. Connect the PC audio output to the PC AUDIO INPUT jack on the set. Turn on the PC and the set. Select RGB-PC input source with using the TV/VIDEO button on the remote control. VIDEO1 AC IN AUDIO L (MONO) VIDEO S-VIDEO AC IN Installation When connecting with a HDMI to DVI cable 32, 37, 42 inch TV Back 26 inch TV Back HDMI DVI (VIDEO) HDMI IEEE 1394 IEEE 1394 PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) DVI INPUT COMPONENT1 INPUT AUDIO INPUT ANTENNA COMPONENT1 INPUT VIDEO INPUT 2-1 2-2 DIGITAL AUDIO OPTICAL AUDIO Select 2-1 or 2-2 RS-232C INPUT (CONTROL/SERVICE) RGB INPUT (PC/DTV INPUT) REMOTE CONTROL COMPONENT1 AUDIO INPUT PC AUDIO INPUT DVI INPUT COMPONENT1 RS-232C INPUT (CONTROL/SERVICE) CABLE VIDEO1 VIDEO1 REMOTE CONTROL OUTPUT G-LINK MONITOR OUT OUTPUT VIDEO INPUT AUDIO L (MONO) VIDEO S-VIDEO AUDIO L (MONO) VIDEO S-VIDEO DIGITAL AUDIO (OPTICAL) G-LINK DIGITAL AUDIO (OPTICAL) DVI-PC OUTPUT PC 2-1 2-2 (R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI OUTPUT PC , depending on your PC connector. Connect the DVI output of the PC to the HDMI jack on the set. 2-1 Connect the PC audio output to the PC AUDIO INPUT jack on the set. 2-2 Connect the PC optical audio output to the DIGITAL AUDIO DVI INPUT jack on the set. Turn on the PC and the set. Select HDMI/DVI input source with using the TV/VIDEO button on the remote control. • If the PC has a DVI output and no HDMI output, a separated audio connection is necessary. • If the PC supports Auto DVI function, the output resolution of the PC will be automatically set to 1280x720p. • If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz. Installation 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either PC INPUT or DVI INPUT to display the PC on the TV. If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.) 3. If using a sound card, adjust the PC sound as required. 4. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. 5. When Source Devices connected with HDMI1/DVI Input, output PC Resolution (VGA, SVGA, XGA), Position and Size may not fit to Screen.Press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center. 6. When Source Devices connected with HDMI1/DVI Input, output TV SET Resolution (480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service center. Supported Display Resolution (RGB-PC, HDMI/DVI Mode) Resolution 640x350 720x400 640x480 800x600 1024x768 7. In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSDdisplay. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center. 8. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC, HDMI/DVI mode. If noise is present, change the PC or HDMI/DVI mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 9. Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. 10.The synchronization input form for Horizontal and Vertical frequencies is separate. Supported Display Resolution (RGB-DTV, HDMI/DVI Mode) Horizontal Frequency (kHz) Vertical Frequency (Hz) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) 31.468 70.09 1280x720p 37.861 45 60 85.08 1920x1080i 67.5 60 31.469 70.08 720x480p 31.5 60 37.927 85.03 31.469 59.94 37.861 72.80 37.500 75.00 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 48.363 60.00 56.476 70.06 60.023 75.02 Reference External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the TV back panel. - RS-232C connection cables are not supplied with the TV. RS-232C Setup AC IN G-LINK DIGITAL AUDIO (OPTICAL) OUTPUT REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) PC AUDIO INPUT RGB INPUT (PC/DTV INPUT) DVI INPUT COMPONENT1 INPUT PC Type of Connector; D-Sub 9-Pin Male No. Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations 3-Wire Configurations (Not standard) 7-Wire Configurations (Serial female-female NULL modem cable) RXD TXD GND DTR DSR RTS CTS PC TV D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC TV D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Reference Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Product Specifications MODEL 26LX1D/2D 32LX1D/2D 32/37/42LP1D Power requirement AC 100-240V~ 50/60Hz 1.5A AC 100-240V~ 50/60Hz 2.0A AC 100-240V~ 50/60Hz 2.0A Television System NTSC-M, ATSC Program Coverage VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125, CADTV 1 ~ 135. DTV 2 ~ 69 External Antenna Impedance 75 Ω • The specifications shown above may be changed without prior notice for quality improvement.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 21 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:bc5e1fb7-fa01-4c82-a5c5-f3e576a33623 Producer : Acrobat Distiller 6.0 (Windows) Create Date : 2005:03:15 17:27:57+09:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2005:03:15 17:38:05+09:00 Metadata Date : 2005:03:15 17:38:05+09:00 Document ID : uuid:6f633df4-e9f7-48c0-86c0-d7b3d0d1e8f3 Format : application/pdf Title : Microsoft Word - User_s Manual_H_.doc Creator : choi Author : choiEXIF Metadata provided by EXIF.tools