LG Electronics USA 37LD650HUA LCD TV Monitor User Manual SAC34134301 Edit1
LG Electronics USA LCD TV Monitor SAC34134301 Edit1
Contents
- 1. User manual-1
- 2. User manual-2
User manual-2
STEREO/SAP BROADCAST SETUP For Analog only: This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program if the station transmits an additional sound signal. Mono sound is automatically used if the broadcast is only in Mono. If other languages are available on the digital signal,select them with the S A P button. MONO SAP Each time you press the S A P button, Mono, Stereo, or S A P appear in turn. 2 RETURN Return to TV viewing. SAP SOUND & LANGUAGE CONTROL STEREO 75 SOUND &LANGUAGE CONTROL AUDIO LANGUAGE Other languages may be available if a digital signal is provided by the broadcasting station. This feature operates only in DTV mode. OPTION Move Enter SOUND & LANGUAGE CONTROL ENTER 4RETURN MENU 76 Enter Menu Language : English Audio Language : English Audio Language : EnglishEnglish Caption : Off Caption : Off Spanish Set ID :1 Set ID :1 French Demo Mode : Off Demo Mode : Off Select OPTION. Select Audio Language. ENTER Move : English Data Broadcasting 1 MENU OPTION Menu Language Select your desired language. Return to the previous menu. Return to TV viewing. Data Broadcasting ON-SCREEN MENUS LANGUAGE SELECTION The menus can be shown on the screen in the selected language. OPTION Move Enter ENTER ENTER 4RETURN MENU Enter Menu Language Audio Language : English Audio Language Caption : Off Caption Set ID :1 Set ID : English English : English Español : Off Français :1 Demo Mode : Off Demo Mode : Off Select OPTION. Select Menu Language. Select your desired language. From this point on, the on-screen menus will be shown in the selected language. Return to the previous menu. Data Broadcasting SOUND & LANGUAGE CONTROL Move : English Data Broadcasting 1 MENU OPTION Menu Language Return to TV viewing. 77 SOUND &LANGUAGE CONTROL CAPTION MODE Analog Broadcasting System Captions Captions are provided to help the hearing impaired watch TV. Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen and is usually the program's dialog. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to memorize the caption/text mode which was last set when you turned the power off. This function is only available when Caption Mode is set O n. OPTION Move Enter OPTION Move Menu Language : English Menu Language : English Audio Language : English Audio Language : English Caption : Off Caption : CC1 Set ID :1 Set ID :1 Demo Mode : Off Demo Mode : Off Data Broadcasting Data Broadcasting Enter Mode On CC1 Digital Option Close SOUND & LANGUAGE CONTROL 1 MENU Select OPTION. ■ ENTER Select Caption. ■ ENTER Select O n. ■ Select C C 1-4 or Text1-4. 5RETURN MENU 78 Return to the previous menu. Return to TV viewing. When selecting O f f, Sub-menus for Analog, DTV, and Digital Option become disabled. CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. Digital Broadcasting System Captions Choose the language you want the DTV/CADTV Captions to appear in. Other Languages can be chosen for digital sources only if they are included on the program. This function in only available when Caption Mode is set On. OPTION Move Enter OPTION Move Menu Language : English Menu Language : English Audio Language : English Audio Language : English Caption : Off Caption : CC1 Set ID :1 Set ID :1 Demo Mode : Off Demo Mode : Off Data Broadcasting Data Broadcasting Enter Mode On CC1 Digital Option Close Select OPTION. ENTER Select Caption. ENTER Select O n. Select C C 1-4, Text1-4, or Service1 - 6. 5RETURN MENU SOUND & LANGUAGE CONTROL 1 MENU Return to the previous menu. Return to TV viewing. 79 SOUND &LANGUAGE CONTROL Caption Option Customize the DTV captions that appear on your screen. This function in only available when Caption Mode is set On. OPTION Move Menu Language : English Audio Language : English Caption : Off Set ID :1 Demo Mode : Off Enter Data Broadcasting OPTION Move Menu Language : English Audio Language : English Caption Set ID Demo Mode : Off :1 Mode : Off Data Broadcasting Enter On CC1 Digital Option Close Custom Size A Standard Font Font 1 Text Color White Text Opacity Solid Bg Color Black Bg Opacity Solid Edge Type None Edge Color Black Close SOUND & LANGUAGE CONTROL 1 MENU ENTER Select Caption. ■ ■ ■ ENTER Select O n. ■ Select Digital Option. ENTER Select Custom. ■ ■ ■ 7 RETURN MENU 80 Select OPTION. Customize the S i z e, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language. Return to the previous menu. Return to TV viewing. ■ S i z e: Set the word size. Font: Select a typeface for the text. Text Color: Choose a color for the text. Text Opacity: Specify the opacity for the text color. Bg (Background) Color: Select a background color. Bg (Background) Opacity: Select the opacity for the background color. Edge Type: Select an edge type. Edge Color: Select a color for the edges. TIME SETTING CLOCK SETTING Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually if the current time is set incorrectly by the auto clock function. TIME Move Enter Clock Off Time TIME Move Clock : Off Off Time Enter Auto On Time : Off On Time : Off :Month Off Sleep Timer : Off Sleep Timer :Date Off 21 Year 2009 Hour 10 AM 02 Minute 10 Eastern Time Zone Daylight Saving Auto Close 1 MENU ENTER Select Clock. ENTER Select Auto. TIME SETTING Select T I M E. Select your viewing area time zone : Eastern, Central, Mountain, Pacific, Alaska, or Hawaii. Select Auto, O f f, or O n (depending on whether or not your viewing area observes Daylight Saving time). 6RETURN MENU Return to the previous menu. Return to TV viewing. 81 TIME SETTING Manual Clock Setup If the current time setting is wrong, reset the clock manually. TIME Move Enter Clock Off Time TIME Move Clock : Off Off Time On Time : Off Sleep Timer : Off Enter Manual Month On Time : Off Date 21 Sleep Timer : Off Year 2009 Hour 10 AM 02 Minute 10 Eastern Time Zone Daylight Saving Auto Close 1 MENU TIME SETTING ENTER Select Clock. ENTER Select Manual. Select the Year, Month, Date, Hour, or Minutes option. Set the Year, Month, Date, Hour, or Minutes option. 6RETURN MENU 82 Select T I ME. Return to the previous menu. Return to TV viewing. : Off AUTO ON/OFF TIME SETTING This function operates only if the current time has been set. The Off Time function overrides the On Time function if they are both set to the same time. The TV must be in standby mode for the On Time to work. TIME Move Enter Clock TIME Move Feb. 21, 2009 10:10 AM Clock Off Time : Off Off Time On Time : Off On Time Sleep Timer : Off Sleep Timer Enter : Off Repeat : 6:30 AM (Once) Hour : Off Minute Once 6 AM 30 Close 1 MENU ENTER Select Off Time or On Time. ENTER Select Repeat. TIME SETTING Select T I M E. Select O f f, O n c e, Daily, Mo n.~FF r i ., M o n.~S a t ., S a t .~ S u n ., or S u n .. Select and set Hour or Minute. 6RETURN MENU Return to the previous menu. Return to TV viewing. 83 TIME SETTING SLEEP TIMER SETTING The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. TIME Move Enter Clock TIME Move Enter Clock Off Time : Off Off Time : Off Off On Time : Off On Time : Off 10 min. Sleep Timer : Off Sleep Timer : Off 20 min. 30 min. 60 min. 90 min. 120 min. 180 min. 240 min. 1 MENU ENTER Select Sleep Timer. TIME SETTING ENTER 4RETURN MENU 84 Select T I ME. Make appropriate adjustments. Return to the previous menu. Return to TV viewing. ■ ■ To cancel the Sleep Timer, select O f f. Press the SLEEP button repeatedly to select the number of minutes. PARENTAL CONTROL / RATINGS Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by choosing the type of the program and the categories. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-tovideo movies use the Movie Rating System (MPAA) only. Ratings for Television programs including made-for-TV movies : TV-G ■ TV-PG ■ TV-14 ■ (General audience) (Parental guidance suggested) (Parents strongly cautioned) TV-MA (Mature audience only) (All children) ■ TV-Y ■ TV-Y7 (Children 7 years older) ■ PARENTAL CONTROL / RATING 85 PARENTAL CONTROL /RATINGS SET PASSWORD & LOCK SYSTEM Lock System Enables or disables the blocking scheme you set up previously. LOCK Move Lock System 1 MENU Block Channel Block Channel Movie Rating Movie Rating TV Rating-Children TV Rating-Children TV Rating-General TV Rating-General Downloadable Rating Downloadable Rating Input Block Input Block 4RETURN Select L O C K. MENU Enter : On Set Password Select Lock System. Off On Return to the previous menu. Return to TV viewing. ■ Select O n or O f f. ENTER Move Lock System Set Password ENTER LOCK Enter : Off When you select O n, the Lock System is enable. PARENTAL CONTROL / RATING Setting up Your Password Set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu. LOCK Lock System Move Enter : On Enter Password Set Password Block Channel Movie Rating Close TV Rating-Children TV Rating-General Downloadable Rating Input Block 1 MENU Select L O C K. ■ ■ .:/, ABC DEF MNO GHI JKL PQRS TUV &@ 86 ENTER WXYZ Input the password. When you select O n, the Lock System is enable. The TV is set up with the initial password “0-0-0-0”. Set Password Set up blocking schemes to block specific channels, ratings, and external viewing sources. A password is required to gain access to this menu. LOCK Move Lock System 1 MENU ABC DEF JKL MNO PQRS TUV &@ LOCK Lock System Move Enter : Off Set Password Set Password Block Channel Block Channel Movie Rating Movie Rating TV Rating-Children TV Rating-Children TV Rating-General TV Rating-General Downloadable Rating Downloadable Rating Input Block Input Block ENTER GHI .:/, Enter : Off New Confirm Close Select L O C K. Input the password. WXYZ Select Set Password. .:/, ENTER GHI PQRS 5RETURN MENU ABC DEF JKL MNO TUV &@ WXYZ Choose any 4 digits for your new password. As soon as the 4 digits are entered, re-enter the same 4 digits on the Confirm. Return to the previous menu. Return to TV viewing. PARENTAL CONTROL / RATING 87 PARENTAL CONTROL /RATINGS CHANNEL BLOCKING Blocks any channels that you do not want to watch or that you do not want your children to watch. LOCK Move Lock System Enter : Off Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Input Block Ch. Change Navigation Block/Unblock 1 MENU ABC DEF GHI JKL MNO PQRS TUV &@ .:/, Select L O C K. Input the password. WXYZ PARENTAL CONTROL / RATING 88 ENTER Select Block Channel. ENTER Select a channel to block or unblock. Block or unblock a channel. 6RETURN MENU Return to the previous menu. Return to TV viewing. CH Page Change Previous MOVIE & TV RATING Movie Rating (MPAA) Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. LOCK Move Enter LOCK Move Enter Blocking off : Permits all programs Lock System 1 MENU DEF JKL MNO TUV &@ Set Password Block Channel Block Channel Movie Rating Movie Rating TV Rating-Children TV Rating-Children TV Rating-General TV Rating-General Downloadable Rating Downloadable Rating Input Block Input Block Select L O C K. Input the password. WXYZ Select Movie Rating. ENTER 5RETURN MENU : Off Select G, P G, PG-13, R, NC-17, X, or Blocking Off. Return to the previous menu. PG PG-13 NC-17 Blocking Off G (General audience) ■ PG (Parental guidance suggested) ■ PG-13 (Parents strongly cautioned) ■ R (Restricted) ■ NC-17 (No one 17 and under admitted) ■ X (Adult only) ■ Blocking Off (Permits all programs) G If you set PG-13: G and PG movies will be available, PG-13, R, NC-17 and X will be blocked. ■ PARENTAL CONTROL / RATING ABC GHI .:/, Lock System Set Password ENTER PQRS : Off Return to TV viewing. 89 PARENTAL CONTROL /RATINGS TV Rating Children Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. LOCK Move Lock System 1 MENU ABC DEF GHI JKL MNO TUV .:/, Lock System Move Enter : Off Set Password Block Channel Block Channel Movie Rating Movie Rating TV Rating-Children TV Rating-Children TV Rating-General TV Rating-General Downloadable Rating Downloadable Rating Input Block Input Block Age Fantasy Violence Close Select L O C K. Input the password. WXYZ PARENTAL CONTROL / RATING Select TV Rating-Children. ■ ENTER Select A g e or Fantasy Violence. ENTER Select block options. 6 RETURN MENU 90 : Off LOCK Set Password ENTER PQRS Enter Return to the previous menu. Return to TV viewing. ■ Age (applies to TV-Y, TV-Y7) Fantasy Violence (applies to TV-Y7) TV Rating General Based on the ratings, blocks certain TV programs that you and your family do not want to view. LOCK Move Lock System Enter : Off LOCK Move Lock System Enter : Off Set Password Set Password Block Channel Block Channel Age Movie Rating Movie Rating Dialogue TV Rating-Children TV Rating-Children Language TV Rating-General TV Rating-General Sex Downloadable Rating Downloadable Rating Violence Input Block Input Block Close 1 MENU ENTER ABC DEF GHI JKL MNO PQRS TUV .:/, Select L O C K. Input the password. WXYZ Select TV Rating-General. ■ ENTER Select A g e, Dialogue, Language, S e x or Violence. ■ ■ Select block options. ■ 6 RETURN MENU Return to the previous menu. ■ Age (applies to TV-G,TV-PG,TV-14,TVMA). Dialogue-sexual dialogue (applies to TV-PG,TV-14). Language-adult language (applies to TV-PG, TV-14, TV-MA). Sex-sexual situations (applies to TV-PG, TV-14, TV-MA). Violence (applies to TV-PG, TV-14, TVMA). PARENTAL CONTROL / RATING Return to TV viewing. 91 PARENTAL CONTROL /RATINGS DOWNLOADABLE RATING This function is available only for digital channels. This function operates only when TV has received Region5 Rating data. Move Lock System Enter : Off LOCK Move Lock System Enter : Off LOCK Set Password Set Password Block Channel Block Channel Movie Rating Movie Rating Humor Humor Sport TV Rating-Children TV Rating-Children Cruelty TV Rating-General TV Rating-General Language Downloadable Rating Downloadable Rating Sadness Input Block Input Block Genre Age Close ■ 1 MENU PARENTAL CONTROL / RATING ENTER ABC DEF GHI JKL MNO PQRS TUV &@ .:/, Input the password. WXYZ Select Downloadable Rating. ENTER Select desired Downloadable Rating option. ENTER Select desired option and block it. 6RETURN MENU 92 Select L O C K. Return to the previous menu. Return to TV viewing. Based on rating table, your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. EXTERNAL INPUT BLOCKING Enables you to block an input. LOCK Move Lock System Enter : Off LOCK Lock System Move : Off Set Password Set Password Enter AV1 Off Block Channel Block Channel AV2 Movie Rating Movie Rating Component Off TV Rating-Children TV Rating-Children RGB-PC Off TV Rating-General TV Rating-General HDMI1 Off Downloadable Rating Downloadable Rating HDMI2 Off Input Block Input Block Off Close 1 MENU ABC DEF GHI JKL MNO PQRS TUV &@ .:/, ENTER Select L O C K. Input the password. WXYZ Select Input Block. ENTER Select input source. Select O n or O f f. 6 RETURN MENU Return to the previous menu. PARENTAL CONTROL / RATING Return to TV viewing. 93 COMMERCIAL MODE SETUP INTERACTIVE TV SETUP Channel Guide Hotel Information Help Exit POWER TV STB DVD VCR PORTAL GUIDE PPV GEM-TV Setup 1. Make all connections as required of PPV system. 2. Set TV to default condition. 3. Configure all relevant installer menu items and TV features. 4. Install PPV card. In most cases the PPV card is preprogrammed with the PPV provider master TV setup. GEM-TV Setup Without PPV Card Refer to Commercial Mode Setup on page 97. 1. See installer menu pages and make settings as required for Gem operation. 2. Specify a Gem Start Channel for item 119 that will tell the TV which channel to tune in for Gem operation. 3. Set TV features on TV Channel, Picture, Audio etc. menus as indicated on page 97. INFO i Gem Operation Interactive Menu Features Use the Gem remote provided in the room to operate both interactive menu and the regular TV features. ENTER RETURN MENU INPUT CC VOL ALPHA/NUM CH MUTE REMOVE COMMERCIAL MODE SETUP 94 ABC GHI JKL PQRS .:/, TUV &@ Channel Guide Shows available TV programs. Indicates channel, program start and finish time and identifies the TV network. Hotel Information Shows typical hotel information. Such as photos of Guestroom, Dining, Business Center, Fitness, Pool, and Facility. And any contributing Partners such as local schools in co-operation programs with the lodge. DEF MNO Help Provides help for the interactive menus. WXYZ FLASHBK PIP RATIO TIMER SAP PIP CH- PIP CH+ PIP SWAP PIP INPUT Exit Removes the interactive menu from the screen. Note: The TV clock must be set before Gem data can be downloaded. INSTALLER OVERVIEW GEM PTC INSTALLER MENU Operating Installer Menu To set up the controls for the TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu. LG Installer Remote You will need an LG Installer remote control similar to the one shown to the right. The installer remote must have a “Source” button or its equivalent. The remote shown in this manual has “INPUT” -- this button serves the purpose of a Source button. 000 INSTALLER SEQ UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 Typical Installer Menu POWER TV STB The TV’s clonable features need to be set up. This is a critical step. If the Master TV display panel’s clonable features like adding channel icons or channel labels are not done correctly, then all the cloned TVs will have problems. Refer to the Owner’s Manual for other TV features: Video, Audio, Closed captions, V-Chip, etc. 000 DVD VCR PORTAL GUIDE INFO i ENTER RETURN MENU INPUT TLL-1100A Clone Programmer The TLL is a very simple cloner to use. It can be set up to clone a master TV setup and transfer it into a target TV. Cloning is accomplished using the TV/Cloner MPI ports for communication. Be sure the Master TV is set up completely. Cloning is only possible when the TV is tuned to an Analog channel, not a digital channel. TLL1100A TV Link Loader-Demo Ready RECEIVE MUTE REMOVE .:/, SEND TLL1100A GHI PQRS ABC JKL TUV 0&@ MENU ENTER DEF MNO WXYZ FLASHBK PIP RATIO TIMER SAP PIP CH- PIP CH+ PIP SWAP PIP INPUT COMMERCIAL MODE SETUP MODE CC VOL ALPHA/NUM CH 95 COMMERCIAL MODE SETUP INTERACTIVE TV OVERVIEW Channel Guide Hotel Information Help Exit Through the interactive TV, the lodging guest is offered a more complete venue of lodge services and amenities. Using the TV in the comfort of the hotel room, the guest can browse the lodge resources available and make selections quickly. Charges for these offerings are billed at the time of order. The Prp:Centric TV is connected to the lodge’s billing computer. After the interactive TV is installed, the following hotel and other resources may be available to the hotel guest, assuming that they are provided by the lodge. Interactive Amenities may include the following ■ Pro:Centric Interactive TV Notes Pro:Centric-TV Setup for PPV (Pay-per-view) Operation A PPV card usually has a channel lineup included with the master TV setup. If this is the case, reset TV to default condition, set any TV features and installer menu items as required and then insert the PPV pre-programmed card into the MPI slot. ■ COMMERCIAL MODE SETUP 96 After TV setup, remove the AC power cord for 15 seconds. Important! ■ The TV will take a few minutes to load electronic program information. If enough time has not elapsed for the TV to acquire EPG data, the TV may operate erratically; menus may not work or TV will not respond to IR remote key presses. ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Hotel Information, News and Events. Directory Services, (Tourist attractions, Restaurants, etc.) Reservation Service (Business Meetings, Fitness, SPA, etc.) Weather, Traffic Information. Shopping Services (Delivery to Guest Room) Room Service (Menu Ordering, Memo Service, Morning Wake Up Call, Laundry, etc.) Ticketing Services. Check Out Service (in the Guest Room). Gaming Services. Email resources, guest can access an email account, etc. Other offerings as they become available..... COMMERCIAL MODE SETUP FOR MASTER TV This page provides an overview of a Master TV configuration. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning (Channel search) is disabled if there is an Aux input active. Commercial Mode Setup Procedure 1. Set Installer Menu Items (Enter TV Installer Menu, see Installer menus for detailed instructions.) a. Set Installer menu item 117 FACT DEFAULT, to 001 and press ENTER on Installer remote. (This clears all installer menu custom settings, channel labels / icons etc. and reloads the factory default settings.) b. Set Item 003 BAND/AFC. - Broadcast: set to 000. - HRC: set to 002 - CATV: set to 001. - IRC: set to 003 c. Set item 028 CH OVERIDE to 001. This allows access to channel search, Auto Tuning and Channel List/Edit options in the Channel Menu. d. Set other particular installer items that affect your TV programming network. Enable/Disable Aux sources, set a Gem Start Channel etc. e. After all required installer menu item settings have been adjusted, press ENTER on the remote to remove Installer Menu. 2. Set Up TV Features (Channel, Picture, Audio, Lock, Time, Option, Digital Captions etc. See TV Clonable options list and TV menus pages.) 4. Transfer TV Setup to Internal TV Controller: 2-5-5 + Menu Mode After the TV channel scan has been edited and channel label icons added, enter the Installer menu. Once in the Installer menu, press 2-55 and MENU on the remote. This transfers the TV setup to the internal controller box. 5. Add Custom Channel Labels for Analog Channels: 2-5-4 + Menu Mode Enter Installer menu, press 2-5-4 and MENU. Add your own custom text labels to channel onscreen displays. Note: Digital Channels often have a broadcaster generated label. (See 2-5-4+Menu pages.) When finished, to exit 2-5-4+Menu mode, press MENU. xxLG710H PTC INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 For 32/37/42/47/55LD650H xxLD650H PTC INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 Typical TV Installer Menu 117 FACT DEFAULT 00X 003 BAND/AFC 00X 028 CH. OVERIDE 001 Adjust the settings for these Installer Menu Items DIGITAL 19-3 MONO STEREO SAP WXYZ Custom Text Label ‘WXYZ’ created in 2-5-4 + Menu (Add Channel Label) Mode 093 RJP AVAILABLE 001 Set 093 RJP Available to 001 if using a remote jack pack 028 CH. OVERIDE 000 After Master TV setup has been completed, set item 028 Ch Overide to 000. COMMERCIAL MODE SETUP 3. Run Auto Tuning (Channel Search) (Search for all available channels.) Go to the Channel menu and access the Auto Tuning option, follow onscreen instructions. a. Edit Channel Scan. In the Channel Menu, access Channel Edit option. ■ Add/Delete channels per your system requirements. Note: Physical channel numbers are used to identify Virtual channels. ■ Add familiar channel trademarks/logos like ABC, CBS, NBC etc. to the Channel-Time onscreen display. In the Channel menu, select the Channel Label option. Add identifiable labels (logos) for the end user to readily know what common networks are available. For 32/37/42LG710H Verify TV Setup At this point, verify that the channel lineup, channel icons and custom labels are correct. Make sure the TV features are set per your requirements. Set item 028 Ch Overide to 000 to lock the channel scan. After the preceding has been completed, the Master TV setup is ready to be copied to a Clone Programmer, see cloning options pages. 97 COMMERCIAL MODE SETUP MASTER TV PROFILE SETUP LEARNING/TEACHING WITH USB MEMORY CARD On Master TV, Create Profile and Learn 1. Set up all Master TV features on the menus and do a Channel Search. Add Channel and Aux Labels etc. Do 255+menu on Installer Menu to save current TV into flash memory. 2. Plug a USB memory drive into the USB In port on the master TV. 3. Press the Menu key to open the Main menu. Highlight the Option icon. 4. Press the Left arrow key once, the Option icon on left side of menu will be highlighted. 5. Press number key ‘7’ a total of 7 times. 6. Gain access to “Learn From TV”. A. First, the Expert Download Menu page will not show the “Learn From TV” option. In order to make it available, key in the password which is used to enter Installer Menu. Example 9-8-7-6. B. By pressing the up/down arrow keys(if there are other menus), place the cursor on Learn From TV, then press the Enter Key. 7. Using the Up/Down arrow keys, highlight “Learn From TV” and then press Enter. 8. To identify this profile from others, you can change the last 5 digits. Key in a custom file name and then press the Enter key. 9. The Learning status will be shown in the progress bar. As soon as learning is complete, a message will appear on the screen indicating the learning process is done. 10. Remove the USB memory card. USB Download Menu Upgrade TV Software Learn From TV UPGRADING... Upgrade TV Software 100% Teach To TV Do not unplug! Learn From TV If necessary, the file name can be edited or changed. For 32/37/42LG710H Learn From TV Select the file name and press OK to start COMMERCIAL MODE SETUP Optional: Edit/Change File Name xxLG710H-UA00001.TLL Previous Enter For 32/37/42/47/55LD650H Learn From TV Select the file name and press OK to start xxLD650H-UA00001.TLL Previous 98 Enter ! NOTES Do not remove TV power cord or USB memory card while Learning, doing so might harm your USB memory card. Do not remove TV power cord or USB memory card while Teaching, doing so may cause the TV to malfunction. G You are allowed to edit the file name, however, a file with edited contents will not be recognized. G Since clock data is copied into USB memory card as numeric data, the time difference between teaching and learning is not automatically adjusted. Either set the clock manually, or use Auto Clock set on TV main menu. On Target TV, Teach Master TV Profile 1. Plug the USB memory card with the Master TV Profile setup into the Target TV’s USB input port. 2. Press Menu key to open the Main menu and then highlight the Option Menu icon. 3. Press the Left arrow key once, this will highlight the Option icon on left side of menu. 4. Press the number key ‘7’, a total of 7 times. 5. Using the Up/Down arrow key, select ‘Teach to TV’, then press Enter key. 6. Use the Up/Down arrow keys to navigate through profiles. Select the profile that you want to install by highlighting it and pressing the Enter key. 7. Teaching progress will be shown on the progress bar. As soon as teaching is done, a message will appear indicating that the teaching process has been completed. 8. When the Teaching is done, Remove the USB memory card and unplug TV power cord. 9. Reconnect the TV’s power cord. Power the TV On and the master setup should be resident on the TV. For 32/37/42LG710H Teach To TV xxLG710H-UA00001.TLL Previous Enter For 32/37/42/47/55LD650H Teach To TV xxLD650H-UA00001.TLL Previous Enter Teach To TV UPGRADING... 40% Do not unplug! COMMERCIAL MODE SETUP 99 COMMERCIAL MODE SETUP TLL-1100A CLONING CONNECTIONS/LEARNING SETUP Connections for the TLL-1100A Clone Programmer to Learn the TV Master TV Setup On Master TV Set up all Master TV features in the menus and do a Channel Search. Add Channel and Aux labels etc. See previous page. Insert an MPI cable into the TV’s MPI port. On TLL-1100A 1. Turn On the TLL-1100A. 2. Use the Mode button to select Clone Mode. 3. Use the Left/Right arrow to select the CBank (1 - 8) to store the master setup in. 4. Plug the other end of the MPI cable into the MPI port on the bottom of the TLL. 5. With the Installer remote control, select item 1 on TLL menu. 6. Press Enter, to transfer the Master setup into CBankX on the TLL. The TLL will copy the master setup. 7. When learning is done, disconnect MPI cable from Master TV. 8. Reconnect TV power cord. Power the TV On and the master setup should be resident on the TV. COMMERCIAL MODE SETUP 100 On Target TV 1. Connect MPI cable from the TLL to the MPI port on the Target TV. Assure that the correct CBank(X) is selected on TLL.. 2. With the Installer remote control select item 2, to Teach the target TV the master TV setup. 3. Press Enter to begin teaching. 4. When Teaching is done, disconnect MPI cable and power the TV Off. Unplug TV power cord. 5. Reconnect TV power cord. Power the TV On and the master setup should be resident on the TV. CLONE SELECTION MENU Selected Bank: CBank X Saved (1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP M.P.I. Learning Setup Antenna (or CATV) TV Link Loader-Demo CLONE CLOCK = 00:00 TV CLOCK = 00:00 THE CLONE IS VERSION V2.2.2 -To change menu items, Press channel keys or digits. -To execute item, Press ENTER. TLL1100A Ready MODE MENU ENTER RECEIVE SEND TLL1100A M.P.I. Teaching Setup Antenna (or CATV) TV Link Loader-Demo CLONE SELECTION MENU Selected Bank: CBank X Saved (1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP TLL1100A Ready MODE MENU ENTER RECEIVE CLONE CLOCK = 00:00 TV CLOCK = 00:00 THE CLONE IS VERSION V2.2.2 -To change menu items, Press channel keys or digits. -To execute item, Press ENTER. SEND TLL1100A Warning Do not use the TLL-1100A while any PPV card is installed in the TV or the clone programmer device will be dam- ! NOTE It is assumed that the TV is connected to a signal source, the TV source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the TLL Cloner main menu is displayed on the TV screen, see above. G If an analog channel is not available, tune the TV to an Aux source like AV-1 for cloning purposes. LT2002 CLONING CONNECTIONS/LEARNING SETUP Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup Antenna or CATV Ferrite Core (TDK, ZCAT 2035-0930) Connect cable to TV MPI Jack and follow on screen instructions Status Indicator MPI Color • green • red Reset battery ok battery low Blink pattern • slow power on no communications • heartbeat power on communications ok THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION XX XX XX QuickSet II Programmer LT2002 CLONE CLOCK = XX:XX TV CLOCK = XX:XX -PRESS ANY KEY TO CONTINUE. -DISCONNECT CLONE WHEN DONE. Clone Programmer Master TV Warning Do not use LT2002 while any PPV card is installed in TV or the clone programmer device will be dam- ! NOTE It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, see above and next page. G If an analog channel is not available, tune TV to an Aux source like AV-1 for cloning purposes. ■ ■ ■ ■ The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.) Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer can store up to 3 different ‘master’ setups.) WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable. Use an Installer’s remote to operate Learning and Teaching menus. Make sure that the batteries in the Clone programmer are fresh. ■ ■ ■ ■ ■ If batteries are removed, the Clone Clock time will be lost. Decide if you want to set the time from the Clone programmer or copy the time to the Clone programmer; from a compatible TV which has the clock set to the current time. Setting the time and transferring it to the Clone or other device is a separate procedure. Follow the connection diagram above to connect the Clone to a Master TV TV display panel. After learning is complete, to another identical TV TV display panel to “teach” it the master setup. See the Clone Troubleshooting section to resolve problems. COMMERCIAL MODE SETUP Before you begin cloning... Turn to the next page to continue Cloning Setup. 101 COMMERCIAL MODE SETUP LT2002 CLONING LEARNING SETUP Learning the Master TV Setup Instructions for the Clone Programmer to Learn the Master TV Setup Use MPI Cable to Connect LT2002 Clone Programmer to Master TV MPI Port If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote. Learn Setup from Master TV Press 1 to select the “LEARN FROM TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” you want to store the master TV’s setup in by pressing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup programmed into it, that setup will be overwritten by the new master TV’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup. Set the Clock (Optional) COMMERCIAL MODE SETUP 102 Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.) Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability. After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.) THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION CLONE CLOCK= TV CLOCK= XX XX XX XX:XX XX:XX -PRESS ANY KEY TO CONTINUE. -DISCONNECT CLONE WHEN DONE. This menu should appear by itself after the LT2002 is connected to the TV MPI port. CLONE SELECTION MENU (1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP -TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS. -TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER This menu should appear after any key is pressed on the Installer remote. LT2002 Clone Programmer Communication Problems ■ A slow flashing green light indicates there are communication problems between the TV and the LT2002 clone programmer. If this is the case, check for a damaged cable, poor contacts, or other connection troubles. ■ If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries. CLONING CONNECTIONS/TEACHING SETUP Teaching the Master Setup to Another TV Connections for the LT2002 to Teach another TV the Master Setup Antenna or CATV Ferrite Core (TDK, ZCAT 2035-0930) Connect cable to TV MPI Jack and follow on screen instructions Status Indicator MPI Color • green • red Reset battery ok battery low Blink pattern • slow power on no communications • heartbeat power on communications ok THE CLONE HAS CONTROL OF THE TV THE CLONE IS VERSION THE TV IS VERSION THE SW IS REVISION XX XX XX CLONE CLOCK = XX:XX TV CLOCK = XX:XX -PRESS ANY KEY TO CONTINUE. -DISCONNECT CLONE WHEN DONE. Target TV QuickSet II Programmer LT2002 Clone Programmer ! NOTE If an analog channel is not available, tune TV to an Aux source like AV-1 for cloning purposes. CLONE SELECTION MENU (1) LEARN FROM TV (2) TEACH TO TV (3) SET CLONE CLOCK FROM TV (4) SET TV CLOCK FROM CLONE (5) DISPLAY TV SETUP (6) DISPLAY CLONE SETUP Teach Master TV’s Setup to the target TV This menu should appear after any key is pressed on the Installer remote. TEACHING IN PROGRESS, PLEASE WAIT This display will appear during Teaching function. COMMERCIAL MODE SETUP After learning is complete, remove the M.P.I. cable from the master TV and connect it to the target TV that you want to copy the master TV’s setup into. With “THE CLONE HAS CONTROL OF TV” message displayed, press 2 or use either Channel key to go to the “TEACH TO TV” option, press ON/OFF, POWER, or ENTER. Select the LT2002 memory that the new setup is in. Press On/Off to transfer the new setup and other information to the new TV. Teaching usually takes 2-3 minutes. After the “TEACHING COMPLETE” message is displayed, press any key to return to the Clone menu, then press ON/OFF, POWER, or ENTER. If finished, detach M.P.I. cable from the target, newly-cloned TV. -TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS. -TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER Disconnect TV Power for 15 Seconds Unplug the AC power cord of the newly-cloned TV from the power outlet for about 15 seconds to activate the newly-copied setup. TEACHING COMPLETE This display will appear after Teaching is complete. 103 COMMERCIAL MODE SETUP INSTALLER MENU Use the Installer’s Menu to set up or change operational settings. See more detailed descriptions of the Installer menu items on the following pages... Accessing the Installer’s Menu Make sure TV is on. Installer’s menu items can be accessed by using an installer’s remote control. Just press MENU repeatedly until the TV seems to stop responding, then press 9, 8, 7, 6, then ENTER to access the Installer’s menu. To remove the Installer’s menu, press ENTER again. Any changes you make will be stored in nonvolatile memory. (The menu also disappears automatically.) The Installer’s menu opens with item 000 INSTALLER SEQ 000. Use the Up/Down arrow keys to sequence through the available menu items. Or, access an item directly by keying in the line number, then pressing MENU. For example, to access the Sleep Timer option which is item 015, press 0-1-5, then MENU. To change a setting, use the Left/Right arrow keys. Or, enter a value directly. For 32/37/42LG710H xxLG710H PTC INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 For 32/37/42/47/55LD650H xxLD650H PTC INSTALLER MENU 000 INSTALLER SEQ 000 Using the Installer’s Menu Items 000 ~ 119 are immediately accessible only upon entering the UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 Installer’s Menu. Their numbers, descriptions, ranges, factory default settings, and a place for listing any changes made on-site are given below and on the following pages. Typical Installer Menu Activating changes made to the Installer’s Menu After exiting the Installer menu, power the TV off and then back on to activate changes to the Installer menu. Installer Menu Items 000 through 034 COMMERCIAL MODE SETUP 104 Menu Item 000 001 002 003 004 005 007 008 009 010 011 015 016 017 021 022 023 028 029 030 031 032 034 Function Value Range Default Value Brief Description of Function and Comments INSTALLER SEQ 0~3 Leave default set to 0. POWER MANAGE 0~7 Sets number of hours of no activity before auto shut Off. AC ON 0/1 Set to 1 to enable auto turn On at power up. BAND/AFC 0~3 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC STRT CHANNEL 0 ~ 127, 255 255 Channel at turn-on (Set to 255 to tune in last channel before power Off). CHAN LOCK 0/1 If set to 1, cannot tune from current channel. STRT VOLUME 0 ~ 63, 255 255 Sets Volume level at TV turn-on (Set 255 to retain last volume level). MIN VOLUME 0 ~ 63 Sets minimum allowable volume setting. MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting. MUTE DISABLE 0/1 Set to 1 to disable mute function. KEY DEFEAT 0/1 Set to 1 to disable menu navigation keys on display panel. SLEEP TIMER 0/1 Set to 1 to enable Sleep Timer. EN TIMER 0/1 Set to 1 to enable On/Off Timers. ALARM 0/1 Set to 1 to enable Alarm. V-CHIP 0/1 Set to 1 to enable V-Chip functions. MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip (Parental Control) blocking hours. CAPTION LOCK 0/1 Set to 1 to retain caption setting at power Off. CH. OVERIDE 0/1 If set to 0, limits direct access to favorite channels. OLD OCV 0/1 Set to 1 to change M.P.I. operation to OCV. ACK MASK 0/1 If set to 1, changes M.P.I. for some OCV boxes. POLL RATE 20 ~ 169 94 Selects poll rate for M.P.I. TIMING PULSE 186 ~ 227 207 Sets baud rate for M.P.I. CAMPORT EN 0/1 Set to 1 to enable Video 2 input. Installer Menu Items 035 through 119 Menu Item Function Value Range Default Value Brief Description of Function and Comments 035 038 039 COMPPORT EN. YPrPb EN. REAR AUX EN 0/1 0/1 0/1 Note 1. Set to 0 to disable HDMI 1. Set to 1 to enable HDMI 1. Set to 1 to enable display panel Component Video 1 input jacks. Set to 1 to enable display panel Video 1 input jack. 040 AUTO CAMPORT 0/1 046 STRT AUX SRCE 1 ~ 6, 255 Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE cannot be set to 2. Sets the starting AUX source. 047 AUX STATUS 0/1 053 069 070 071 DIS. CH-TIME M. EN. CH-T COL. FOR. CH-TIME BCK. CH-TIME 0/1 0/1 0~7 0~7 073 CH NOT AVBLE 0/1 If set to 1 and channel override is 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the favorite channel list. 075 078 079 080 081 082 REVERT CH UPN MSB UPN MSB-1 UPN MSB-2 UPN LSB CHKSM ERROR 0/1 0 ~ 255 0 ~ 255 0 ~ 255 0 ~ 255 0/1 If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel. User programmable number, most significant byte. User programmable number, most significant byte - 1. User programmable number, most significant byte - 2. User programmable number, least significant byte. Enforces rigid M.P.I. checksum. 083 HANDSHK TIME 0~5 Relaxes M.P.I. timing to be compatible with PC based Windows-controlled systems. 084 PERMANENT BLK 0/1 Removes block hours setting for Parental Control and makes block permanent. 087 REAL BGB EN. 088 090 091 EN NOISE MUTE KEY LOCK YPrPb2 093 RJP AVAILABLE 0, 1, 2, 5, 6 Set to 0 to disable. Set to 1, 2, 5 or 6 for HDMI or DVI mode. (See detailed descriptions) 094 SAP MENU EN 0/1 Set to 0 to disable feature on Function menu. Set to 1 to enable feature on Function menu. 096 DEF. ASP. RATIO 0~4 Sets default aspect ratio at power up. See detailed descriptions and item 106. 099 BACK LIGHTING 102 ATSC BAND 0 / 2 / 18 (For xxLG710H) 2 (For xxLG710H) 0 / 1 / 17 (For xxLD650H) 1 (For xxLD650H) 0/1 0/1 0/1 Note 1. Set to 0 to disable RGB1. Set to 2 for PC. Note 1. Set to 0 to disable RGB. Set to 1 to enable RGB. If set to 1, mutes audio if no signal is present. If set to 1, keyboard is locked out, IR is still functional. Set to 0 to disable HDMI 2. Set to 1 to enable HDMI 2. Sets the brilliance of the TV picture backlighting. Settings above 101 control dynamic back lighting and enable power saving mode. Selects ATSC band. 103 ATSC TUNE MODE 0/1 Default 01 for physical channel scan. Set to 0 for Virtual Channel scan. 104 START MINOR CH 0 ~ 255 Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor channel number. 106 ASP RATIO LOCK 0/1 116 117 VIDEO MUTE EN FACT DEFAULT 0/1 0/1 To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle. Set to 0 for normal, set to 1 for Blank. 0=Normal. 1=Loads presets of all above settings. 118 POWER SAVING 1, 3, 7 119 DATA CHANNEL 0 ~ 135 COMMERCIAL MODE SETUP 1 ~ 100 101 ~ 200 255 (For xxLG710H) 201, 202, 255 202 (For xxLD650H) 0~4 Set to 1 for M.P.I. AUX source to be reported as a channel number instead of Channel 0. Set to 1 to disable Channel-Time display. Set to 1 to enable custom color for the Channel-Time display. Chooses custom foreground color for the Channel-Time display. Chooses custom background color for the Channel-Time display. Set to 1 to be powered at b-Lan module. Set to 3 to bo powered at b-Lan module only when TV is powered on. Set to 7 to be not powered at b-Lan module. Sets the DATA Channel. Note 1: Dependent on item 093 RJP Available setting. 105 COMMERCIAL MODE SETUP Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu. 0 = 9876 1 = 4321 2 = 1478 3 = 3698 001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain On, unless there has been activity from either the control panel or remote control. 002 - AC ON (AC Power Switchable) If set to 1, allows the TV to turn On just by applying AC power. Pressing the On button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is Off, and 1 is On. NOTE: If set to 1 (On), the TV does not respond to On/Off commands from either the remote or the display control panel, and the SLEEP TIMER is also nonfunctional. 003 - BAND/AFC (Band/Automatic Frequency Control) There are 4 possible settings for this option: 0 = Broadcast 2 = HRC 1 = CATV 3 = IRC COMMERCIAL MODE SETUP If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here and add the channels using the Channel Edit option in the Channel Menu. 004 - STRT CHANNEL (Start Channel) If active, this function allows you to determine the initial channel number when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed when the TV was turned Off, to be the tuned to channel when the TV is turned On again. Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number. 255 = Last channel 1 ~ 125 = Ch X 0 = Aux 126 Map to Channel 3. 127 Map to Channel 4. 106 005 - CHAN LOCK (Channel Lock) CHAN LOCK is ideal if the system must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default). Generally, this feature is used in connection with START CHANNEL (Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV will remain locked on Channel 3. NOTE: For Items 007, 008 and 009 For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV. To translate a TV volume level to the installer menu value, use the following formula: Installer Value = TV Value x 63 100 Enter only the whole number (disregard fractions). 007 - STRT VOLUME (Start Volume) This function allows the Installer to determine the initial volume level setting when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned On. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned Off; at turn On, the volume level will be automatically set at the previous or last level. 008 - MIN VOLUME (Minimum Volume) This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63 — change values with ADJ Left/Right arrow. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every TV. NOTE: The minimum volume level cannot have a value setting higher than the MAX VOLUME level (described below). 009 - MAX VOLUME (Maximum Volume) This function determines the maximum volume level allowable with the VOLUME (VOL) Up/Down controls. In this way, for example, someone can not set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Change values with ADJ Left/Right arrow keys. It may be best to set the same value on every TV. NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously). 010 - MUTE DISABLE Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted. 011 - KEY DEFEAT (Keyboard Defeat) If set to 1, key defeat prevents the end user from accessing the on-screen menus with the display front panel—MENU, SELECT, and Left / Right arrow keys do not function. If set to 0, those keys do function. NOTE: The menus can always be accessed by pressing MENU on the remote. 015 - SLEEP TIMER If set to 1, the SLEEP TIMER feature may be used. If set to 0, the Sleep Timer is not available. 016 - EN TIMER (Enable On/Off Timers) If set to 1, Timer function is available to user and enabled continuously. Set to 0 to disable On/Off Timers. (Clock must be set in order to use Timers.) 021 - V-CHIP (Parental Control) * Set to 1 to activate V-Chip (Parental Control); have it available to end user to filter and control or otherwise restrict programming content that can appear. Set to 0 to turn V-Chip feature Off, not available to user; no programming restrictions can be set. 022 - MAX BLK HRS (Maximum Block Hours) * Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours. 028 - CH. OVERIDE (Channel Override) If set to 1, the user can select channels with either Channel up/down or by direct keypad entry. If set to 0, only those channels that are entered for scanning can be selected. 029 - OLD OCV (On Command VideoTM) Set to 1 for operation with systems from On Command Corporation. 030 - ACK MASK M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. When set to 1, changes M.P.I. for some OCV boxes. 031 - POLL RATE M.P.I. Communication Parameter. Selects Poll Rate for M.P.I. Leave at default setting unless changed by PayPer-View provider. Step size of 16 ms. 032 - TIMING PULSE M.P.I. Communication Parameter. Leave at default setting unless changed by Pay-Per-View provider. Sets baud rate. Step size of 4.3 uS. 034 - CAMPORT EN. (Camera Port Enable) Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional. NOTE: S-Video overrides Video jack. 035 - COMPPORT EN. (Computer Port Enable) Enable/disables display panel HDMI1 input jack. Set to 0 to disable, set to 1 to enable. NOTE: The setting above is ignored if Installer item 093 RJP AVAILABLE, is set to 1. 038 - YPrPb EN. (Rear Component Video Enable) Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks. 039 - REAR AUX EN. (Rear Aux Enable) Set to 1 to enable display panel rear AUX (Video 1) input. Set to 0 to disable display panel rear AUX (Video 1) input. Note: S-Video overrides Video. COMMERCIAL MODE SETUP 017 - ALARM * Gives the installer the option of making the Alarm function available to the end user. If set to 1, Alarm function is available to end user. Set to 0 to disable the Alarm function. NOTE: Clock must be set before the Alarm function will work. 023 - CAPTION LOCK Set to 1 to restore previous caption On/Off state after turn Off. If set to 0, captions are always Off at turn On. * Only affects Function Menu if enabled by some PPV providers. 107 COMMERCIAL MODE SETUP 040 - AUTO CAMPORT Set to 1 to automatically switch to Camport when equipment is connected to front Video input. Set to 0 to disable front Video automatic source selection. NOTE: If set to 1, 093 RJP Available is automatically set to 0. 073 - CH NOT AVBLE (Channel Not Available) If set to 1 and item 028 CHANNEL OVERRIDE is set to 0, “NOT AVAILABLE” message is displayed when directly accessing a channel not in the channel scan list available in memory. 046 - STRT AUX SRCE (Start Aux Source) Sets the starting AUX source. At power up, TV will tune to starting Aux source if item 004 Start Channel is set to 0. If item 093 RJP Available is set to 0 and item 040 Auto Camport is set to 0: 1 = Video 1 4 = RGB 255 = Last Aux 2 = Video 2 5 = HDMI 2 3 = HDMI 1 6 = Component 075 - REVERT CH (Revert to Start Channel) If set to 1 and loss of M.P.I. communication occurs, TV automatically tunes to the specified Start Channel. If item 093 RJP Available is set at 1: 2 = Video 2 5 = HDMI 2 6 = Component If item 040 Auto Camport is set to 1: 1 = Video 1 5 = HDMI 2 3 = HDMI 1 6 = Component 4 = RGB 047 - AUX STATUS Set to 1 for M.P.I. AUX source to be reported as a channel number instead of channel 0. Set to 0 to disable AUX identification change. Controls M.P.I. status channel response for AUX inputs. 053 - DIS. CH-TIME (Disable Channel-Time) Set to 1 to disable the Channel-Time display, Channel-Time display will not appear. Set to 0 to enable the Channel-Time display. COMMERCIAL MODE SETUP 108 069 - EN. CH-T COL. (Enable Channel-Time Custom Color) Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display. 070 - FOR. CH-TIME (Channel-Time Display Foreground Color) Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu background is transparent. 071 - BCK. CH-TIME (Channel-Time Display Background Color) Set according to Color Chart. 0 = Black 3 = Yellow 6 = Cyan 1 = Red 4 = Blue 7 = White 2 = Green 5 = Violet NOTE: If foreground and background color are the same, menu background is transparent. 078 - UPN MSB (UPN Most Significant Byte) User programmable number, most significant byte readable by M.P.I. command. Note: Not linked to serial number. 079 - UPN MSB-1 (UPN Most Significant Byte-1) User programmable number, most significant byte-1 readable by M.P.I. command. Not linked to serial number. 080 - UPN MSB-2 (UPN Most Significant Byte-2) User programmable number, most significant byte-2 readable by M.P.I. command. Not linked to serial number. 081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by M.P.I. command. Not linked to serial number. 082 - CHKSM ERROR (Checksum Error) Enforces rigid M.P.I. checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on M.P.I. async port). SPI is always checked. 083 - HANDSHK TIME (Handshake Time) Adds an additional delay to the handshake time which is 64 msec, thus relaxing M.P.I. timing requirements to be compatible with PC based Windows controlled systems, range is 0 5. (Timeout = 25.5MS + [25.5 MS* Handshake time]). 084 - PERMANENT BLK (Permanent Block) Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes. 087 - REAR RGB EN. (Rear RGB Enable) Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 2 for PC for STB RGB input. (For 32/37/42LG710H) Set to 1 for PC for STB RGB input. (For 32/37/42/47/55LD650H) Set to 18 for Auto Configure one time only with power cord removal and reinsertion. (For 32/37/42LG710H) Set to 17 for Auto Configure one time only with power cord removal and reinsertion.(For 32/37/42/47/55LD650H) 088 - EN NOISE MUTE (Enable Noise Mute) If set to 1, audio mutes if no signal is present. 090 - KEY LOCK If set to 1, display panel keyboard is locked out, not available to end user. IR receiver remains functional. 091 - YPrPb2 (HDMI2 Enable) Set to 0 to disable display panel HDMI2 input. Set to 1 to enable DTV mode. Set to 2 to enable PC mode. 093 - RJP AVAILABLE (Remote Jack Pack Available) 0 = Remote jack pack is not available or disabled. 1 = Legacy Model RJPs: HDMI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI. Audio stream is expected from HDMI source. If no audio is present, no audio will be heard. 2 = Legacy Model RJPs, DVI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI however, Audio is from selected audio source, based on the RJP’s audio hierarchical priority. 5 = Scaler Model RJPs, HDMI Mode Enables RJP when an HDMI cable is inserted into RJP. VIdeo is from HDMI. Audio stream is expected from HDMI source. If no audio is present, no audio will be heard. 6 = Scaler Model RJPs, DVI Mode Enables RJP when an HDMI cable is inserted into RJP. Video is from HDMI however, Audio is from selected audio source, based on the RJP’s audio hierarchical priority. Notes : ■ See Reference section, RJP Input Hierarchy and RJP Models page. ■ If set to 1, 2, 5 or 6, item 040 Auto Camport is automatically set to 0. Settings 1, 2, 5 and 6 allow the lodge staff to customize each TV’s RJP setup based on customer requirements. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up, see settings below. Set to 0 “Set By System”. Set to 1 for 4:3. Set to 2 for 16:9 (Factory Default). Set to 3 for ‘Just Scan’ Set to 4 for Zoom 099 - BACK LIGHTING Sets the TV screen brightness at power up, see settings below. Default setting value is 255. (For 32/37/42LG710H) Default setting value is 202. (For 32/37/42/47/55LE650H) 1 - 100 Static Backlighting. (1 = Dimmest picture, 100 = Brightest picture.) 101 - 200 Dynamic Backlighting. 102 - ATSC BAND Sets up TV to receive different types of incoming signals: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC. 103 - ATSC TUNE MODE Sets ATSC tuning mode: Default set to 1 for Physical channel scan. Set to 0 for Virtual Channel scan. 104 - START MINOR CHANNEL Sets XX-XX minor start channel number at power up: 0=NTSC. If not 0, number selected is the Minor start channel number. 106 - ASP RATIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power Off. Set to 0 to retain default aspect ratio with power Off. See item 96 Default Aspect Ratio above. 116 - VIDEO MUTE EN (Video Mute Enable) Set to 0 for normal. Set to 1 for blank. 117 - FACT DEFAULT (Factory Default) Set to 0 for normal. Set to 1 to load presets to all of the previous item settings. WARNING: Setting this to 1 will reload the factory defaults and clear the channel list including erasing any assigned Channel Icons and custom channel Labels. 118 - POWER SAVING Default is set to 3. When TV is in Standby mode, MPI card slot is powered by Standby power supply and embedded BLAN is not powered. When TV is in Power On mode, MPI card slot is powered by main 12V power supply and embedded BLAN is powered. Note, TV must be powered on in order to communicate with the embedded BLAN module for configuration and control. Notes : See Reference section, B-LAN SETUP AND OVERVIEW page. COMMERCIAL MODE SETUP 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function menu, if Function menu is available. Set to 0 to disable SAP feature on Function menu, if Function menu is available. (101 = Dimmest picture, 200 = Brightest picture.) 201 Automatic Static Backlighting 202 Automatic Dynamic Backlighting Set to between 101 and 200, TV automatically controls backlighting depending upon the picture level of the current program. Set to 201, TV automatically controls backlighting depending upon external spectral sensitivity. Set to 202, TV automatically controls backlighting depending upon external spectral sensitivity and picture level of the current program. Set to 255, to disable power saving mode. ■ 119 - DATA CHANNEL Sets the Data channel. Set the channel number that will provide data to the TV at turn on. Initially the TV may take several minutes to load program data from AC power off state. 109 COMMERCIAL MODE SETUP REFERENCE: DETAILED INSTRUCTIONS FOR MAKING A MASTER TV IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING... To set up a master TV you will need to know how to enter the TV Installer menu and make changes to the default values as required. If necessary, familiarize yourself with the TV Installer menu and how to make and save changes in the menu, before attempting to clone the TV Master TV setup. You will also need an LG Installer remote control similar to the one shown in the front of this manual. The installer remote must have a “Source” button or its equivalent. The remote shown in this manual has a “INPUT” button -- this button serves the purpose of a Source button. is a critical step. If the Master TV display panel’s clonable features like adding channel icons or channel labels, digital font options etc., are not correctly added, then the cloned TVs will all have problems. As the cloning procedure is being performed, specific steps need to be done at the indicated times to achieve the desired result. Be sure to do each task as indicated. If a procedure or step is left out or not performed completely, cloning may not work. At each step, pay attention to assure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step and cloning may not be successful. Cloning is only possible when the signal source is an Analog channel, not a digital channel. Finally, the TV’s clonable features need to be set up. This Making a Master TV Detailed Instructions COMMERCIAL MODE SETUP 110 The following describes the procedure for preparing a Master TV for cloning and the procedure for adding Channel Icons and/or Labels. Note 1: Disconnect all Aux inputs. Under certain conditions, Auto Tuning Channel Search is disabled if there is an Aux input active. Note 2: Under certain conditions, changes to the input mode of the RGB inputs will not take effect until the power is cycled (TV is turned Off and On). To avoid confusion, disconnect all RGB inputs before entering the Installer menu. 1. Enter the TV installer menu. a. Reset the internal controller to factory default by accessing installer menu item 117 FACT DEFAULT, set it to 1 and press “ENTER”. The value will change back to 0 after the TV’s internal controller has been restored to factory default condition. This step will ensure that the TV channel memory will be the active channel list. Check the Status LED. If it is blinking rapidly then the TV channel map is in use. b. Within the Installer menu, set the Installer menu items to the configuration required of your institution. c. It is important to set the tuning band at this time, see Installer menu item 03 BAND/AFC. d. Set Installer menu item 28 – CH OVERIDE to 001 to allow access to the Auto Tuning and Ch. Edit features in the Channel Menu. Exit the Installer menu. 2. Access the Master TV menus and set the clonable options on the menus to the desired configuration. Refer to the Clonable Menu Features Chart in this manual. 3. Run Auto Tuning to find analog and digital channels. 4. Enter the Channel Edit menu and edit the channel lineup to include the Free-To-Guest Channels only. 5. Assign ICONs to the channels using the Channel Label Menu. Note: You can add Channel ICONS typically network logos like ABC, NBC, PBS etc. in this step. Or, in Step 7, add Channel ICONS or labels for channels without Icons. 6. Transfer the TV setup: Enter the TV installer menu. Press ‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup to the internal controller. Once the transfer is complete, the system will exit the Installer menu. Check the Status LED inside the TV. It should be blinking slowly (1 blink per second). 7. Edit/Add Channel ICONs and Channel Labels as needed. Enter Installer menu. With menu displayed, press 2-5-4 + MENU. See next page for detailed instructions: - Editing/Adding Channel ICON and Labels on Master TV - Changing a Channel’s ICON on Master TV - Changing/Adding Channel Labels on Master TV - Changing Source Labels on Master TV 8. Verify Master TV setup and feature configuration: ■ Did you add Channel ICONS? ■ Did you add Channel Labels? ■ Did you add Source Labels? ■ Did you adjust all TV menu options as required? After verifying master setup, enter the TV Installer menu and set Installer menu item 28 CH OVERIDE to 000. Press ENTER to remove and exit the Installer menu. REFERENCE: PROCEDURES FOR ADDING CHANNEL LABEL ICONS/CUSTOM CHANNEL LABELS (2-5-4 + MENU MODE) Adding Channel Icons and Labels in the 2-5-4 + Menu Mode Editing/Adding Channel ICONs and/or Labels If there is no pre-assigned ICON, you can make a custom channel label of up to 7 characters to help in identifying the channel or network. At your option, channel labels can also be added in addition to a preassigned ICON. You may also add labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs. (Icon) XYZ XYZ XYZ NETWORK 1 2 3 4 5 6 7 (Label) Editing and adding the labels can only be done if there are channels entered into the TV’s channel map either by using the method described in item 6, by cloning or by the use of the master remote control from the PPV provider. Note: A blank letter space is available between ‘Z’ and ‘!’. To Do Channel Editing/Labeling, Proceed as Follows 1. Enter TV Installer menu. 2. Once the installer menu appears, press ‘2’, ‘5’, ‘4’, ‘MENU’. This enters the channel label editing mode. Add your channel icons and channel labels in this menu, see below. (You can do this more than once.) 3. To exit the menu when done press “MENU”. Changing/Adding Channel Labels on Master TV Changing Source Labels on Master TV 1. With Channel Up/Down, select the channel you want to change the Icon for. 2. With the Right or Left ADJ arrow, select the thin letter ‘I’ on the channel ID display. 3. With the Up or Down arrow, select the desired ICON you want to appear to identify the channel. (If you know the ICON number, enter the number followed by Enter / Select.) 4. Proceed with Changing/Adding Labels or go to the next channel. 1. Channel Up/Down to select the desired channel. 2. Press the Right or Left ADJ arrow repeatedly until the numbers 1 to 7 show up. The number shows the position of the character that can be changed. Number 1 is the first character, number 2 the second character and so on. 3. With the Up or Down arrow, select the desired character. 4. Proceed to the next number position or use Channel Up/Down to go to the next channel. 1. Press “INPUT” to select the desired Aux input source; A/V 1, A/V 2, HDMI Component, RGB etc. 2. Press the Right or Left arrow repeatedly until the numbers 0 to 9 shows up. The number shows the position of the character that can be changed. 3. Use the Up or Down arrows to select the desired character. 4. Press “INPUT” for the next Aux source or proceed with Changing Icon or Changing/Adding Labels. Press Ch Up/Down to return to channels. Installer Remote Control Key Functions for Master TV Channel Editing/Labeling Menu ■ ■ ■ CHANNEL Up/Down - Tunes in the next channel in scan. Left/Right Arrows - Select the item to change. If “I” is shown, the ICON can be changed. If a number is shown, it indicates the position of the character that can be changed. Up/Down Arrows - Select the ICON or the character to be displayed. Tip: Arrows can be held down for fast scrolling. ■ ■ ■ ■ 0 – 9 - Use to enter the index number of the ICON, if known. ENTER/SELECT - Changes the ICON after the number has been entered. INPUT - Changes the Aux input label. (“Source” on the remote shown in this manual is INPUT.) MENU - Exits the editing process. COMMERCIAL MODE SETUP Changing a Channel’s ICON on Master TV 111 COMMERCIAL MODE SETUP REFERENCE: CLONABLE MENU FEATURES Clonable Menu Features Menu /Sub Menu Features Installer Menu Installer Item settings Channel Auto Tuning (Channel Lineup) Channel Edit Channel label Picture Aspect Ratio Picture Mode Advanced Control Audio Auto Volume Clear Voice ll Sound Mode Balance Audio Contd. Treble Bass SRS TruSoundXT Infinite Sound TV Speaker Option Language Caption Caption Mode DTV Captions Style - Style DTV Captions Style - Size DTV Captions Style - Font DTV Captions Style - Text Color DTV Captions Style - Text Opacity DTV Captions Style - BG Color DTV Captions Style - BG Opacity DTV Captions Style - Edge Type DTV Captions Style - Edge Color Lock Movie Rating TV Rating – Children Age TV Rating – Children Fantasy Violence TV Rating – General Age Input Block Time Auto Clock Manual Clock Off Time On Time Auto Off ! NOTE Picture Menu and other menu settings shown above are not clonable on all TVs. End user has access to Picture, Sound and Ratio on user remote control. G Menu options vary between Analog / Digital channels and Aux Sources. Procedure for Checking Software Version COMMERCIAL MODE SETUP The software version of the TV may be checked by accessing the INSTALLER MENU. To do this, press the MENU button repeatedly until the menu display ceases to respond to MENU key presses. Then, press "9", "8", "7", "6", "ENTER/SELECT". Press ENTER/SELECT again to remove the installer menu from screen. For 32/37/42/47/55LD650H For 32/37/42LG710H xxLG710H PTC INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 Typical Installer Menu 112 xxLD650H PTC INSTALLER MENU 000 INSTALLER SEQ 000 UPN 000-000-000-000 FPGA E0F1 PTC V1.00.000 CPU V3.06.00 REFERENCE: POWER SAVING SETUP Power Savings Setup Installer Item 118 Power Saving: set to 003, enabled (Default). Installer Item 099 Backlighting: value set as shown below. (Default value is 255) For 32LG710H Item 099 Backlighting (Static) 100 90 80 70 60 50 40 30 20 10 Picture Lumin. 206 204 203 172 147 127 108 86 66 50 39 Power Consumption (Watts) 104 103.5 103 93 85 79 73.5 67 60 55.5 51.5 Power Savings Rating 0% 0.48 % 0.96 % 10.58 % 18.27 % 24.04 % 29.33 % 35.58 % 42.31 % 46.63 % 50.48 % Item 099 Backlighting (Dynamic) 200 190 180 170 160 150 140 130 120 110 101 Picture Lumin. 103 96 84 73 64 57 51 44 38 33 29 Power Consumption (Watts) 74 73 69.5 65.5 62 60 57.5 55 52.5 50.5 49 Power Savings Rating 28.85 % 29.81 % 33.17 % 37.02 % 40.38 % 42.31 % 44.71 % 47.12 % 49.52 % 51.44 % 52.88 % Power Consumption (Watts) 91.5 85.5 80 74.8 70.8 67.5 63.5 59.3 56.5 54.5 52.8 Power Savings Rating 39.60 % 43.56 % 47.19 % 50.63 % 53.27 % 55.45 % 58.09 % 60.86 % 62.71 % 64.03 % 65.15 % Note: Values are results of controlled experiments under laboratory conditions. For 37LG710H Picture Lumin. 258 230 201 170 145 120 95 72 54 41 31 Power Consumption (Watts) 151.5 136.5 122.5 111 101.3 91.5 81.3 71 63.5 58 53 Power Savings Rating 0% 9.90 % 19.14 % 26.73 % 33.14 % 39.60 % 46.34 % 53.14 % 58.09 % 61.72 % 65.02 % Item 099 Backlighting (Dynamic) 200 190 180 170 160 150 140 130 120 110 101 Picture Lumin. 93 79 67 58 50 44.5 38 31.5 27 23.5 21 Note: Values are results of controlled experiments under laboratory conditions. COMMERCIAL MODE SETUP Item 099 Backlighting (Static) 100 90 80 70 60 50 40 30 20 10 113 COMMERCIAL MODE SETUP For 42LG710H Item 099 Backlighting (Static) 100 90 80 70 60 50 40 30 20 10 Picture Lumin. 286 250 216 185.5 159 133.5 107.5 81 61 46.5 35 Power Consumption (Watts) 185 164.5 147.5 133.5 121.3 109.5 97 84 75 67.5 61.5 Power Savings Rating 0% 11.08 % 20.27 % 27.84 % 34.43 % 40.81 % 47.57 % 54.59 % 59.46 % 63.51 % 66.76 % Item 099 Backlighting (Dynamic) 200 190 180 170 160 150 140 130 120 110 101 Picture Lumin. 113 108 96 83 73.8 65.2 55.8 46.13 39.6 34.4 29.85 Note: Values are results of controlled experiments under laboratory conditions. COMMERCIAL MODE SETUP 114 Power Consumption (Watts) 109 103 96.4 89.7 84.5 80.2 75.2 69.9 66.1 63.5 61.4 Power Savings Rating 41.08 % 44.32 % 47.89 % 51.51 % 54.32 % 56.65 % 59.35 % 62.22 % 64.27 % 65.68 % 66.81 % TV CAMPORT AUTO SENSE OPERATION The CAMPORT Auto Sense function is enabled when: 1. Installer Menu Item 34, CAMPORT EN is set to 1 AND 2. Installer Menu Item 40, AUTO CAMPORT is enabled (1). Selectable= Can be accessed with INPUT key, direct access, etc. Auto Sense= Switches to this input when connector is inserted. The camport (Side Video) has the highest priority and will override any commands including tuning to the Start Channel. CAMPORT (Front Video) Functionality Control Item 34 Item 40 Front Video CAMPORT EN AUTO CAMPORT Operation Disabled Disabled Selectable Auto Sense CAMPORT Operation (Stand-Alone) When Camport Auto Sense is enabled as above, the TV’s source will switch to the side video aux source whenever a plug is inserted into any of the side video panel inputs (either composite Video or S-Video). Previous State Operation Before Inserting While CAMPORT CAMPORT Is Active Aux or RF Channel None When the plug is removed, the TV will switch back to the previous channel or input source that the TV was using before the plug was inserted. However, if any direct access to an RF channel or Aux channel is requested while the camport is active, then, when the camport plug is removed, the TV will switch to the last requested channel. Source changes using any Source Keys (INPUT) are ignored. Channel Up/Channel Down and Flashback Commands are not direct access tuning commands and they are also ignored. Aux or RF Channel Direct Access Aux or RF Channel Ch Up/Down, Flashback and TV/AV Keys State Upon Removal Of CAMPORT Previous Aux or RF Channel Last Requested RF or Aux Channel Previous Aux or RF Channel CAMPORT Operation (PPV) Previous State Operation Before Inserting While CAMPORT CAMPORT Is Active Aux or RF Channel None State Upon Removal Of CAMPORT Previous Aux or RF Channel Aux or RF Channel Direct Access Last Requested RF or Aux Channel Aux or RF Channel Ch Up/Down, Last Requested Flashback Channel if PPV and TV/AV Keys translates it to direct access tuning command. Otherwise, goes to Previous Aux or RF Channel COMMERCIAL MODE SETUP The operation will be similar to that of the StandAlone mode. However, the PPV providers may send different commands to the TV for the same user commands. For instance, some providers will always send a direct tune command when it receives a channel up/down or a flashback command while other PPV providers will just send a key command. 115 COMMERCIAL MODE SETUP FTG OPERATION SETUP Communications Setup Menu Sets up the communications link between the FTG Configuration Application and the Z7 card installed in a TV/STB. CHANNEL PICTURE AUDIO TIME OPTION LOCK INPUT USB Typical TV/STB Setup Menu Shows that the Z7 card is in pass-through mode. This menu can also be accessed by turning IR remote access ‘On’ in the FTG Configuration Application, while the TV/STB is in FTG mode. ASPECT RATIO Move Enter Set By Program ABC 4:3 16:9 COMMERCIAL MODE SETUP Zoom Just Scan End User ‘Aspect Ratio’ or Function Menu Shows that the Z7 card is in FTG mode. While this menu is present on-screen, the only way the Installer menu can be accessed is by the FTG Configuration Application. Network Icon Selection Menu Select channel icons like ABC, NBC etc., to add to the channel OSDs to identify common networks for the end user. 116 FTG CHANNEL MAP OVERVIEW LOGICAL CHANNEL NUMBERS Channels appear in numerical order. Select logical, Major and Minor numbers on menu. CUSTOM CHANNEL LABELS/ICONS Set custom labels and select icons on menu. SET CHANNEL ATTRIBUTES Set encrypted, OSD on or off or blank video only. DELETE Removes channel from lineup. ADD After inputting a new channel’s data, press to add channel to list. CHANNEL MAP EDITOR Shows both channel data and logical channel lineup. COMMERCIAL MODE SETUP EXIT Exits menu and returns to logical channel listing. UPDATE After editing a channel’s data, press to include the changes in the channel list. 117 COMMERCIAL MODE SETUP FTG INSTALLER MENU OVERVIEW CONFIGURATION SETTINGS Select tabs for Installer submneu items to set up TV/STB. COMMERCIAL MODE SETUP INSTALLER DEFAULTS Press to reset TV/STB to Installer menu defaults. IR REMOTE ACCESS Toggle IR remote access to On to get access to TV/STB feature menus or Installer menu. WRITE Press to transfer the FTG Installer menu values to the FTG card and TV/STB. READ Press to transfer the Installer menu values on the FTG card to the PC FTG Configuration Application. 118 HOSPITAL GRADE TV/STB ITEMS Set hospital only items on Installer menu for Hospital grade TV/STBs. EXIT Returns to logical channel map menu. LEARN Press to transfer the installer menu settings on the TV/STB to the FTG card and PC FTG Configuration Application. FTG OPERATION TROUBLESHOOTING LMT7Z7 Configured Card in FTG Mode of Operation Error Messages Problem Probable Cause Solution Cannot contact target. FTG application already open. Close extra FTG application on computer. Cable(s) not connected. Check and connect communication cables. TV off. Turn TV on. Wrong Communication port. Select correct Comm port on computer. TV AUX INPUT CONFIGURATION ENABLE DIRECT ACCESS Tuning TV Installer Menu OLD_OCV OLD_OCV= Source Input Source Mode Number =0 MPI DATA MPI DATA STATUS TYPE 0x41 SOURCES ENABLED (R/W) Labeling Value Labeling Value Labeling Video Front (Camport) Video Front (Camport) 90 Video2 (Side) CV/SVIDEO 34 CAMPORT_EN 0x01 131 91 Video1 (Rear) CV/SVIDEO 39 REAR_AUX_EN 0x02 DTV 91 YPrPb2 EN = 1 0x04 132 92 PC 91 YPrPb2 EN = 2 0x04 DTV 35 COMPPORT EN = 1 0x08 PC 35 COMPPORT EN = 2 0x08 PC 87 REAR RGB EN = 2 0x10 SVGA Rear Computer 38 YPrPb EN 0x40 Y/UV Component 93 HDMI2 HDMI1/DVI 134 94 RGB 136 96 Component 137 97 USB 121 USB Options Rear Video (Aux) S-Video Rear S-Video Rear Front Computer Front Computer 0x80 Y/C Front Video DATA START AUX STATUS SOURCE TYPE 0X0D ASSIGNMENT AUX SOURCE (R) 0 (VIDE0) Rear Video 0 (VIDE0) (Aux) S-Video 0 (VIDE0) Rear S-Video Rear (COMPUTER) Front 0 (VIDE0) Computer Front Computer (COMPUTER) SVGA Rear Computer (COMPUTER) Rear Y/PrPb Componen video 0 (VIDE0) 2 (Comp) NA Front t S-Video COMMERCIAL MODE SETUP 130 133 DATA STATUS TYPE 0xD2 CURRENT AV SOURCE (R) 119 COMMERCIAL MODE SETUP B-LAN SETUP AND OVERVIEW B-LAN Setup and Overview Power to the B-LAN module is controlled by Installer Menu Item 118 Power savings. By default, value 003, the BLAN module is only powered on when the TV is powered on. There are two bits in the Power Savings item to control power to the B-LAN module, one for power during TV Standby mode and one for power during TV Power On mode. When the bit is 0, the B-LAN module is powered. When the bit is 1, the B-LAN module is not powered (Power Savings is Enabled). TV Standby State TV Power On State Power Saving COMMERCIAL MODE SETUP 120 BLAN Power MPI Slot Power BLAN Power MPI Slot Power On Standby On Main Off Standby On Main Off Standby Off Main The B-LAN module is internal to the TV. It allows the Hotel/Institution headend equipment to communicate with the TV for configuration and control. This communication is via the institution’s RF distribution system. The control device at the headend (ex FMA-LG101) can control multiple TVs. When the TV is first installed, it must be powered on in order for the headend to be able to communicate with the B-LAN. At this point, if it is desired for the BLAN to always be powered on, particularly during Standby mode, the BLAN Standby Power Saving mode setting should be downloaded as Disabled. The new settings will not be active until the BLAN actually downloads the configuration data to the PTC and the PTC is reset. If it known that the application requires only using the MPI card slot and not the embedded BLAN, the installer can go into the Installer Settings menu and enable the BLAN Power Savings mode, in both Standby and TV power on. APPENDIX TROUBLESHOOTING Abnormal Operation Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. ■ Ensure that the batteries are installed with correct polarity (+ to +, - to -). ■ Ensure that the correct remote operating mode is set: TV, VCR etc. ■ Install new batteries. ■ The remote control doesn’t work Power is suddenly turned off Is the sleep timer set? ■ Check the power control settings. Power interrupted. ■ Video Problems Check whether the product is turned on. ■ Try another channel. The problem may be with the broadcast. ■ Is the power cord inserted into wall power outlet? ■ Check your antenna direction and/or location. ■ Test the wall power outlet, plug another product’s power cord into the outlet where the product’s power cord was plugged in. ■ No picture &No sound Picture appears slowly after switching on ■ This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. Adjust Color in menu option. ■ Try unplugging any others electronics that are near by to see if interference is causing the problem. ■ Try another channel. The problem may be with the broadcast. ■ Are the video cables installed properly? ■ Activate any function to restore the brightness of the picture. ■ No or poor color or poor picture ■ Check for local interference such as an electrical appliance or power tool. Station or cable product experiencing problems, tune to another station. Station signal is weak, reorient antenna. ■ Check for sources of possible interference. ■ Poor reception on some channels ■ Lines or streaks in pictures ■ Check antenna (Change the direction of the antenna). ■ If the HDMI cables don’t support High Speed HDMI, it can cause flickers or no screen display. In this case use the latest cables that support High Speed HDMI. No picture when connecting HDMI APPENDIX Horizontal/vertical bars or picture shaking 121 APPENDIX Audio Problems Press the VOL or VOLUME button. Sound muted? Press the MUTE button. ■ Try another channel. The problem may be with the broadcast. ■ Are the audio cables installed properly? ■ ■ Picture OK but No sound No output from one of the speakers ■ Adjust Balance in menu option. ■ A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. Unusual sound from inside the product No sound when connecting HDMI or USB Check High Speed HDMI cable. Check USB cable over version 2.0. ■ Use normal MP3 file. ■ ■ *This feature is not available for all models. PC Mode Problems The signal is out of range Vertical bar or stripe on background & Horizontal Noise & Incorrect position Screen color is unstable or single color Adjust resolution, horizontal frequency, or vertical frequency. ■ Check the input source. ■ ■ Work the Auto configure or adjust clock, phase, or H/V position. (Option) Check the signal cable. ■ Update video card drivers. ■ APPENDIX Power No Power ■ See troubleshooting flow chart. ■ Adjust Installer menu settings as required. ■ After 2-5-5 + MENU, only channels included in TV controller will appear. If channel is available it can be added to channel scan, rescan channels. If it is not available, the ‘No Signal’ message appears on the TV screen. Erratic Operation Installer menu setup Software Problems Cannot direct enter channel number or “No Signal” appears ! NOTE 122 For other problems not caused by the TV, refer to other devices’ operating guides. REFERENCE: LT2002 CLONING PROCEDURE TROUBLESHOOTING Warning: Do not use the LT2002 while any PPV card is installed in the TV or the clone programmer will be damaged. Reset Clone After Static Shock After replacing exhausted batteries, or if the programmer behaves strangely after a static shock, use a paper clip or similar instrument inserted through the small hole marked ”RESET” to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to reset the Clone Programmer clock from a TV containing the correct time. Note The LT2002 programmer is designed to be used with TVs containing the 221-01006 and later processors. Use with earlier TV sets may give unpredictable results. Processors used before the 221-01006-04 have a limited screen display capability. They cannot display entire screens as shown in the quick setup instructions accompanying the LT2002 clone programmer. Use the printed menu illustrations on the quick setup sheet supplied with the Clone as an aid to making your programming choices. (Although the menus are not all displayed, the clone functions all operate normally.) Clone Programmer Troubleshooting Clone Programmer Press Reset on clone programmer, redo teach/learn. (Teach/Learn should take a minimum of 1 minute.) Clone copies Setup in less than 30 seconds ■ Remote32LG3DC does not operate clone (32LG3DC-UA) 32LG3DCH ■ Only use an LG Installer remote to operate the clone programmer with the TV. (32LG3DCH-UA) Connect the M.P.I. cord properly, assure a good connection. TV must be powered On for the clone to work. ■ Install 4 fresh AA high-quality alkaline batteries. ■ Clone menu hard to read ■ Connect the TV to a reliable Analog channel signal source. No time set ■ Set the time on a TV and then copy the time to the Clone Programmer. ■ ■ Try a different LT2002 Clone programmer. Reset the Clone Programmer. ■ Retry cloning again. Clone not working Clone Scans Channels more than once Master and Other TVs APPENDIX LED does not blink ■ Wait until procedure complete message is displayed. ■ Cloning is only possible with identical model TVs. ■ Reread cloning pages to be sure all tasks were performed. 32LG3DCH ■ Cloning did not work 32LG3DC (32LG3DC-UA) Clone time disappeared New Setup not present ■ ■ (32LG3DCH-UA) ■ Batteries must remain installed to retain time settings. ■ Disconnect newly-cloned TV from power for 5 seconds. After cloning operations are complete, just unplug the LT2002 from the TV. If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels. 123 APPENDIX TROUBLESHOOTING FLOW CHART Controller Quick Check Is 'STATUS' LED on Analog Board Blinking No Yes Is TV Connected to AC Power No Plug into AC Power Outlet Press 'POWER' or 'ON/OFF' key on TV Yes Defective TV Did TV Turn On No 1. Defective TV Yes Is Red LED on TV Lit No Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or 'MUTE' key on Installer Remote 1. Defective Analog Board. 2. Defective Digital Board. Yes Did TV Respond Cycle the power by removing and re-connecting the AC power cord. Observe the 'POWER' LED and TV screen as soon as AC power is re-applied. Did Analog Board 'POWER' LED Turn On Momentarily Press 'POWER' or 'ON/OFF' or 'VOLUME UP/DOWN' or 'MUTE' key on User-Supplied Remote No Defective TV APPENDIX Did TV Respond Yes No Check to see if TV is in Commercial Mode. See Commercial Mode Check chart. Yes End 124 1. Defective TV 2. Go to Remote Control Checklist Yes Yes Did TV Turn On Momentarily No No 1. Defective PPV Card 2. Go to Remote Control Checklist COMMERCIAL MODE CHECK RJP Model List Press the "On/Off" key on the front panel. The On/Off key is always operational. Did you get a response REFERENCE: RJP MODEL LIST AND INPUT HIERARCHY No Defective TV Yes Leave the TV set On Go to Installer menu by pressing "MENU" until the TV stops responding. Legacy Models Scaler Models RJP-101M Not Support PCB RJP-101ML Not Support PCB RJP-110F RJP-210F RJP-110FW RJP-210FW RJP-110W RJP-210W RJP-110WBR RJP-210WBR RJP-110S RJP-210S RJP-120G RJP-220G RJP-120T RJP-220T RJP-201B RJP-301B RJP-202B RJP-302B RJP Input Hierarchy Did TV stop responding or continue to respond Stopped responding Continued to respond TV is in Commercial Mode. Priority Video Audio 1st. (Highest) HDMI/DVI 3.5mm Mini Jack 2nd. RGB L/R Audio In 3rd. Composite HDMI/DVI 4th. (Lowest) TV (RF of Aux) TV (RF or Aux) TV is not in Commercial Mode Call Technical Support for Assistance APPENDIX 125 APPENDIX GLOSSARY OF TERMS A list of definitions for some of the words found in this guide 75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire sticking through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV. 300 TO 75 OHM ADAPTER A small device that connects a two-wire 300 ohm antenna to a 75 ohm RF jack. They are usually about an inch long with two screws on one end and a round opening with a wire sticking out on the other end. ANALOG TELEVISION Standard television broadcasting format in 4:3 picture aspect ratio. A/V CABLES Audio/Video cables. Three cables bunched together—right audio (red), left audio (white), and video (yellow). A/V cables are used for stereo playback of videocassettes and other A/V devices. A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television). APPENDIX AMPLIFIER An electronic device that amplifies sound from a television, CD player, VCR, DVD, or other Audio/Video device. ANTENNA The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna. CABLE Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals. CABLE TELEVISION Programming provided by a cable service. 126 DIGITAL TELEVISION Televisions signals that are transmitted digitally. DVI Digital Video Interface Accommodates analog and digital interfaces with a single connector. COMPOSITE VIDEO Typical video jack, uses one wire for transporting three-color video signals. COMPONENT VIDEO Uses three wires for transporting threecolor video signals. Supports higher quality video. DELETED Lets you remove channels from the list that the end user can scroll through using CH (Channel) Up/Down. HDMI High-definition multi-media interface. HDTV High-definition television. Refers to television signals that have higher resolution than ordinary analog TV signals. HDSTB High-definition set top box. Refers to a tuner device that receives high-definition television signals which have higher resolution than ordinary analog TV signals. INPUT Refers to the input jack that receives a signal from a TV, VCR, DVD Player or other Audio/Video device. JACK An input or output connector on the back of a TV, VCR, DVD Player or other Audio/Video device. MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio. OUTPUT Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device. PHYSICAL CHANNEL NUMBER The actual channel number. Analog channels use the physical channel number and digital channels can use a virtual channel number. RGB (Red, Green, Blue) Connection input or output port available for producing a video image using three separate colors: Red, Green, and Blue. RS-232 Serial communication port through which firmware is downloaded. 2ND AUDIO PROGRAMMING/SAP Second Audio Programming (SAP) is another, separate audio channel available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French. SIGNAL Picture and sound traveling through a cable, or over the air, to the TV. STEREO SOUND Stereo (Stereophonic) sound refers to audio that’s divided into right and left sides. TUNER Device that picks up the broadcast signal and turns it into picture and sound. VIRTUAL CHANNEL NUMBER A re-mapped channel number. Analog channels use the actual channel number, but digital channels use a virtual(or fake) channel number. XDS Extended Data Service: Additional program information included on the signal provided at the discretion of the broadcaster. MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. ! WARNING Do not use window/glass cleaner or anything with ammonia to clean the screen. Cleaning the Cabinet ■ ■ To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence CAUTION If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. APPENDIX 127 APPENDIX PRODUCT SPECIFICATIONS MODELS 32LG710H (32LG710H-UA) 37LG710H (37LG710H-UA) 42LG710H (42LG710H-UA) 797 x 597 x 232.5 mm 31.3 x 23.5 x 9.15 inch 918.6 x 684.8 x 293.4 mm 36.1 x 26.9 x 11.5 inch 1026.2 x 734.1 x 293.4 mm 40.4 x 28.9 x 11.5 inch Dimensions (Width x Height x Depth) With stand Without stand 797 x 558.7 x 109.3 mm 31.3 x 21.9 x 4.3 inch 918.6 x 635.8 x 111.7 mm 36.1 x 25.0 x 4.39 inch 1026.2 x 687.9 x 111.8 mm 40.4 x 27.0 x 4.4 inch Weight With stand Without stand 12.89 kg / 28.41 lbs 11.41 kg / 25.15 lbs 17.97 kg / 39.61 lbs 15.41 kg / 33.97 lbs 21.10 kg / 46.51 lbs 18.48 kg / 40.74 lbs MPI card 3.1 x 0.9 x 6.3 inch (Width x Height x Depth) 80.0(+0.6/-0.2) x less than 23.0(including pcb thickness) x less than 162.0(excluding cover thickness) mm Cable Card Card Bracket Cover (Width x Height ) Power requirement Television System Program Coverage External Antenna Impedance Environment condition ■ APPENDIX 128 Operating Temperature Operating Humidity Storage Temperature Storage Humidity 3.7 x 1.1 inch 94.7(±0.5) x 28.3(±0.5) mm AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm 32 ~ 104°F (0 ~ 40°C) Less than 80% -4 ~ 140°F (-20 ~ 60°C) Less than 85% The specifications shown above may be changed without prior notice for quality improvement. MODELS 37LD650H (37LD650H-UA) Dimensions (Width x Height x Depth) With stand 797.0 mm x 555.0 mm x 207.0 mm (31.3 inch x 21.8 inch x 8.1 inch) 916.0 mm x 625.0 mm x 261.0 mm (36.0 inch x 24.6 inch x 10.2 inch) Without stand 797.0 x 495.0 x 97.1 mm (31.3 inch x 19.4 inch x 3.8 inch) 916.0 mm x 560.0 mm x 88.9 mm (36.0 inch x 22.0 inch x 3.5 inch) Weight With stand Without stand 11.1 kg (24.4 lbs) 9.4 kg (20.7 lbs) 14.6 kg (32.1 lbs) 12.0 kg (26.4 lbs) 42LD650H (42LD650H-UA) 47LD650H (47LD650H-UA) 1024.0 mm x 685.0 mm x 261.0 mm (40.3 inch x 26.9 inch x 10.2 inch) 1137.0 mm x 758.0 mm x 270.0 mm (44.7 inch x 29.8 inch x 10.6 inch) MODELS Dimensions (Width x Height x Depth) With stand Without stand 1024.0 mm x 621.0 mm x 87.1 mm (40.3 inch x 24.4 inch x 3.4 inch) 1137.0 mm x 685.0 mm x 76.8 mm (44.7 inch x 26.9 inch x 3.0 inch) Weight With stand Without stand 17.7 kg (39.0 lbs) 15.1 kg (33.2 lbs) 20.3 kg (44.7 lbs) 18.3 kg (40.3 lbs) MODELS 55LD650H (55LD650H-UA) Dimensions (Width x Height x Depth) With stand 1329.0 mm x 872.0 mm x 330.0 mm (52.3 inch x 34.3inch x 12.9 inch) Without stand 1329.0 mm x 796.0 mm x 96.5 mm (52.3 inch x 31.3 inch x 3.7 inch) Weight With stand Without stand 33.0 kg (72.7lbs) 29.8 kg (65.6 lbs) Environment condition Operating Temperature Operating Humidity Storage Temperature Storage Humidity AC100-240V ~ 50/60Hz NTSC-M, ATSC, 64 & 256 QAM VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 75 ohm APPENDIX Power requirement Television System Program Coverage External Antenna Impedance ■ 32LD650H (32LD650H-UA) 32 ~ 104°F (0 ~ 40°C) Less than 80% -4 ~ 140°F (-20 ~ 60°C) Less than 85% The specifications shown above may be changed without prior notice for quality improvement. 129 APPENDIX PROGRAMMING THE REMOTE CONTROL The provided universal remote control can be programmed to operate most remote-controllable devices. Note that the remote may not control all models of other brands. Programming a code into a remote mode APPENDIX 130 Testing your remote control. To find out whether your remote control can operate other components without programming, turn on a component such as a STB(Set-Top Box) and press the corresponding mode button (such as a S T B) on the remote control, while pointing at the component. Test the POWER and C H buttons to see if the component responds correctly. If the component does not operate correctly, the remote control requires programming to operate the device. Turn on the component to be programmed, then press the corresponding mode button (such as S T B) on the remote control. The remote control button of the desired device is illuminated. Press the MENU and MUTE buttons simultaneously, and the remote control is ready to be programmed with the code. Enter a code number using the number buttons on the remote control. Programming code numbers for the corresponding component can be found on the following pages. If the code is correct, the device will turn off. Press the MENU button to store the code. Test the remote control functions to see if the component responds correctly. If not, repeat from step 2. Remote Control Code VCR Brand AIWA AKAI Codes Codes Brand MAGNAVOX 031 067 012 069 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 SAMSUNG 043 046 124 146 MARANTZ 033 023 037 031 103 039 043 129 033 MARTA MATSUI MEI MEMOREX 040 033 007 108 116 135 041 010 064 110 111 117 119 MGA MINOLTA MITSUBISHI 023 039 043 053 017 031 037 131 008 025 034 046 138 009 033 109 136 012 018 063 033 033 013 066 063 072 144 147 031 050 150 034 048 012 106 027 035 101 153 010 045 026 034 137 150 015 033 101 033 043 055 060 152 039 043 MTC MULTITECH NEC NORDMENDE OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RCA REALISTIC 013 020 114 123 009 013 014 034 101 106 RICO RUNCO SALORA 013 063 031 031 067 101 013 108 072 011 033 013 040 107 145 003 031 053 058 148 014 033 034 041 068 031 033 067 030 033 010 034 102 046 020 020 051 014 031 053 072 134 139 059 045 046 059 061 040 034 023 039 043 054 070 074 083 140 145 020 031 033 034 067 033 034 054 071 101 021 048 014 066 020 041 109 147 008 033 054 075 033 062 140 145 034 063 144 010 014 034 040 101 Codes 032 105 113 125 SANSUI 022 SANYO 003 102 SCOTT 017 131 SEARS 003 013 031 101 SHARP 031 SHINTOM 024 SONY 003 056 077 SOUNDESIGN 034 STS 013 SYLVANIA 031 067 SYMPHONIC 034 TANDY 010 TATUNG 039 TEAC 034 TECHNICS 031 TEKNIKA 019 101 THOMAS 034 TMK 006 TOSHIBA 008 059 TOTEVISION 040 UNITECH 040 VECTOR RESEARCH 012 VICTOR 048 VIDEO CONCEPTS 012 VIDEOSONIC 040 WARDS 003 031 053 YAMAHA 012 ZENITH 034 058 040 102 104 107 109 112 115 120 122 043 048 135 007 010 014 134 037 112 129 008 009 010 014 017 020 042 073 081 054 149 009 031 052 057 058 076 078 149 033 034 059 034 043 039 043 033 070 031 033 034 013 042 047 082 112 131 101 APPENDIX 034 016 125 AMPRO 072 ANAM 031 AUDIO DYNAMICS 012 BROKSONIC 035 CANON 028 CAPEHART 108 CRAIG 003 CURTIS MATHES 031 DAEWOO 005 065 112 DAYTRON 108 DBX 012 DYNATECH 034 ELECTROHOME 059 EMERSON 006 029 036 129 FISHER 003 FUNAI 034 GE 031 107 GO VIDEO 132 HARMAN KARDON HITACHI 004 043 INSTANTREPLAY 031 JCL 031 JCPENNY 012 040 JENSEN 043 JVC 012 048 130 KENWOOD 014 047 LG (GOLDSTAR) 001 101 LLOYD 034 LXI 003 017 MAGIN 040 Brand 034 046 013 033 054 034 048 072 017 034 131 039 056 080 024 040 043 101 131 APPENDIX HDSTB Brand Codes ALPHASTAR DSR 123 AMPLICA 050 ASTRO PHILIPS(ML) 159 ASTROTHOMPSON(ML)160 ASTRO NOKIA(ML) 161 BIRDVIEW 051 CHANNEL MASTER 013 036 CHAPARRAL 008 CITOH 054 CURTIS MATHES 050 DRAKE 005 011 141 DX ANTENNA 024 ECHOSTAR 038 093 097 122 ELECTRO HOME 089 EUROPLUS 114 FUJITSU 017 133 GENERAL INSTRUMENT 003 031 HITACHI 139 HOUSTON TRACKER 033 057 Brand 126 129 014 015 018 055 009 012 077 145 006 007 010 052 112 116 046 040 094 098 056 057 095 099 076 058 096 100 021 134 004 059 140 037 104 022 027 016 029 101 039 051 Codes HUGHES HUMAX(SL) JANIEL JERROLD KATHREIN LEGEND LG LUTRON LUXOR MACOM 068 158 060 061 108 057 001 132 062 010 065 MEMOREX 057 NEXTWAVE 028 NORSAT 069 PACE SKY SATELLITE 143 PANASONIC 060 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 PRIMESTAR 030 PROSAT 072 PSI(TH) 157 RCA 066 REALISTIC 043 SAMSUNG 123 147 144 059 063 064 124 125 070 142 102 110 111 Brand Codes SATELLITE SERVICE CO 028 085 SCIENTIFIC ATLANTA 032 SKY LIFE 150 SONY 103 STARCAST 041 SUPER GUIDE 020 SAMART(TH) 156 TEECOM 023 088 137 TOSHIBA 002 TRUE VISION(TH) 155 UNIDEN 016 044 078 101 UBC(TH) 153 UBC/SAMART(TH) 154 VIEWSTAR 115 VTC(VN) 162 WINEGARD 128 ZENITH 081 091 035 047 057 138 124 125 026 075 087 090 107 130 127 025 042 043 045 048 049 079 080 086 135 136 146 082 083 084 120 106 074 DVD APPENDIX 132 Brand Codes Brand Codes Brand Codes APEX DIGITAL DENON GE HARMAN KARDON JVC LG MAGNAVOX MARANTZ 022 020 014 005 006 027 012 001 010 016 025 013 024 MITSUBISHI NAD ONKYO PANASONIC PHILIPS PIONEER PROCEED PROSCAN 002 023 008 003 013 004 021 005 RCA SAMSUNG SONY THOMPSON TOSHIBA YAMAHA ZENITH 005 011 007 005 019 009 010 017 009 026 006 006 015 006 008 018 016 025 IR CODES 1. How to Connect ■ Connect your wired remote control to the Remote Control port on the TV. 2. Remote Control IR Codes ■ Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz Tc Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 ■ Configuration of frame 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 Repeat frame Repeat code ■ Tf Lead code 9 ms 4.5 ms ■ Repeat code 0.55 ms ■ 2.25 ms Bit description Bit ”0” Bit ”1” 0.56 ms 0.56 ms 2.24 ms 1.12 ms ■ APPENDIX 9 ms Frame interval: Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 133 APPENDIX APPENDIX 134 (Hexa) Code Function Note 08 POWER Remote control Button (Power On/Off) D6 0F TV Remote control Button 0B INPUT Remote control Button 0A SAP Remote control Button 79 FF RATIO Remote control Button AB GUIDE Remote control Button OC PORTAL Remote control Button AA INFO Remote control Button 10-19 Number Key 0-9 Remote control Button 4C - (Dash) Remote control Button 1A FLASHBK Remote control Button 02 VOL + Remote control Button 03 VOL - Remote control Button 00 CH Remote control Button 01 CH Remote control Button 0E GG TIMER Remote control Button 39 CC Remote control Button 09 MUTE Remote control Button 43 MENU Remote control Button 5B RETURN Remote control Button 40 Remote control Button 41 Remote control Button 07 Remote control Button 06 Remote control Button 44 ENTER Remote control Button 60 PIP Remote control Button 71 PIP CH + Remote control Button 72 PIP CH- Remote control Button 63 PIP SWAP Remote control Button 61 PIP INPUT Remote control Button C1 A Stop Remote control Button C0 G Play Remote control Button C2 l l Pause Remote control Button C3 Ô (Record) Remote control Button Code Function Note TV Discrete IR Code (TV Input Selection) 5A AV1 Discrete IR Code (AV1 Input Selection) D0 AV2 Discrete IR Code (AV2 Input Selection) BF COMPONENT Discrete IR Code (COMPONENT Input Selection) D5 RGB-PC Discrete IR Code (RGB Input Selection) CE HDMI1 Discrete IR Code (HDMI1 Input Selection) CC HDMI2 Discrete IR Code (HDMI2 Input Selection) 76 Ratio 4:3 Discrete IR Code (Only 4:3 Mode) 77 Ratio 16:9 Discrete IR Code (Only 16:9 Mode) AF Ratio Zoom Discrete IR Code (Only Zoom Mode) C4 POWER ON Discrete IR Code (Only Power On) C5 POWER OFF Discrete IR Code (Only Power Off) (Hexa) OPEN SOURCE LICENSE GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it. (Some other free software foundation software is covered by the GNU Lesser General Public License instead.) You can apply it to your programs, too. When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things. To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software. 0. This license applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program" means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running the Program is not restricted, and the output from the program is covered only if its contents constitute a work based on the program (independent of having been made by running the program). Whether that is true depends on what the program does. 1. You may copy and distribute verbatim copies of the program's source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and give any other recipients of the program a copy of this license along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. Also, for each author's protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors' reputations. 2. You may modify your copy or copies of the program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions: Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. APPENDIX For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 135 APPENDIX b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part there of, to be licensed as a whole at no charge to all third parties under the terms of this license. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this license. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this license, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the program. In addition, mere aggregation of another work not based on the program with the Program (or with a work based on the program) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. APPENDIX 136 3. You may copy and distribute the program (or a work based on it, under section 2) in object code or executable form under the terms of sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. 5. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the program (or any work based on the program), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the program or works based on it. 6. Each time you redistribute the program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this license. 7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the program at all. For example, if a patent license would not permit royalty-free redistribution of the program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the program. any later version published by the Free Software Foundation. If the program does not specify a version number of this license, you may choose any version ever published by the Free Software Foundation. 10.If you wish to incorporate parts of the program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. APPENDIX 8. If the distribution and/or use of the program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the program under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the program specifies a version number of this license which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of 137 APPENDIX END OF TERMS AND CONDITIONS How to apply these terms to your new programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found. one line to give the program's name and a brief idea of what it does. Copyright (C)This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the license, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. APPENDIX 138 Also add information on how to contact you by electronic and paper mail. If the program is interactive, make it output a short notice like this when it starts in an interactive mode: Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type ‘show c’ for details. The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items-whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the program ‘Gnomovision’ (which makes passes at compilers) written by James Hacker. signature of Ty Coon, 1 April 1989 Ty Coon, President of Vice This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this license. GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software - to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages - typically libraries - of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below. When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights. We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license. Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs. When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library. We call this license the "Lesser" General Public License because it does Less to protect the user's freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License. APPENDIX To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. 139 APPENDIX Although the Lesser General Public License is Less protective of the users' freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library. each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this license and to the absence of any warranty; and distribute a copy of this license along with the Library. The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a "work based on the library" and a "work that uses the library". The former contains code derived from the library, whereas the latter must be combined with the library in order to run. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This license agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this license”). Each license is addressed as "you". A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.) APPENDIX “Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modification are not covered by this license; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the library does and what the program that uses the library does. 1. You may copy and distribute verbatim copies of the library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on 140 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this license. d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the library, and can be reasonably considered independent and separate works in themselves, then this license, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the library, the distribution of the whole must be on the terms of this license, whose permissions for other licenses extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the library. In addition, mere aggregation of another work not based on the library with the library (or with a work based on the library) on a volume of a storage or distribution medium does not bring the other work under the scope of this license. 3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General Public License applies to all subsequent copies and derivative works made from that copy. This option is useful when you wish to copy part of the code of the library into a program that is not a library. 4. You may copy and distribute the library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of sections 1 and 2 above on a medium customarily used for software interchange. If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this license. When a “work that uses the library” uses material from a header file that is part of the library, the object code for the work may be a derivative work of the library even though the source code is not. Whether this is true is especially significant if the work can be linked without the library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law. If such an object file uses only numerical parameters, data structure layouts and accessories, and small macros and small inline functions (ten lines or less in length), then the use of Otherwise, if the work is a derivative of the library, you may distribute the object code for the work under the terms of Section 6. Any executable containing that work also fall under Section 6, whether or not they are linked directly with the library itself. 6. As an exception to the sections above, you may also combine or link a "work that uses the library" with the library to produce a work containing portions of the library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications. You must give prominent notice with each copy of the work that the library is used in it and that the Library and its use are covered by this license. You must supply a copy of this license. If the work during execution displays copyright notices, you must include the copyright notice for the library among them, as well as a reference directing the user to the copy of this license. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the library and then relink to produce a modified executable containing the modified library. (It is understood that the user who changes the contents of definitions files in the library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6, above, for a charge no more than the cost of performing this distribution. d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy. APPENDIX However, linking a “work that uses the library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the library), rather than a “work that uses the library”. The executable is therefore covered by this license. Section 6 states terms for distribution of such executable. the object file is unrestricted, regardless of whether it is legally a derivative work. (Executable containing this object code plus portions of the library will still fall under Section 6.) 141 APPENDIX For an executable, the required form of the "work that uses the library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the library together in an executable that you distribute. 7. You may place library facilities that are a work based on the library side-by-side in a single library together with other library facilities not covered by this license, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the sections above. b) Give prominent notice with the combined library of the fact that part of it is a work based on the library, and explaining where to find the accompanying uncombined form of the same work. APPENDIX 8. You may not copy, modify, sublicense, link with, or distribute the library except as expressly provided under this license. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the library is void, and will automatically terminate your rights under this license. However, parties who have received copies, or rights, from you under this license will not have their licenses terminated so long as such parties remain in full compliance. 9. You are not required to accept this license, since you have not signed it. However, nothing else grants you permission to modify or distribute the library or its derivative works. These actions are prohibited by law if you do not accept this license. Therefore, by modifying or distributing the library (or any work based on the library), you indicate your acceptance of this license to do so, and all its terms and conditions for copying, distributing or modifying the library or works based on it. 10.Each time you redistribute the library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise 142 of the rights granted herein. You are not responsible for enforcing compliance by third parties with this license. 11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this license, they do not excuse you from the conditions of this license. If you cannot distribute so as to satisfy simultaneously your obligations under this license and any other pertinent obligations, then as a consequence you may not distribute the library at all. For example, if a patent license would not permit royalty-free redistribution of the library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this license would be to refrain entirely from distribution of the library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a license cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this license. 12.If the distribution and/or use of the library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the library under this license may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this license incorporates the limitation as if written in the body of this license. 13.The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the library specifies a version number of this license which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14.If you wish to incorporate parts of the library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found. one line to give the library's name and a brief idea of what it does. Copyright (C) This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the license, or (at your option) any later version. NO WARRANTY 15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice APPENDIX 16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. END OF TERMS AND CONDITIONS How to apply these terms to your new libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). 143 APPENDIX MOZILLA PUBLIC LICENSE Version 1.1 --------------code which is described in the source code notice required by exhibit as original code, and which, at the time of its release under this license is not already covered code governed by this license. 1.Definitions. 1.0.1. “Commercial use” means distribution or otherwise making the covered code available to a third party. 1.1. “Contributor” means each entity that creates or contributes to the creation of modifications. 1.2. “Contributor version” means the combination of the original code, prior modifications used by a contributor, and the modifications made by that particular contributor. 1.3. “Covered code” means the original code or modifications or the combination of the original code and modifications, in each case including portions thereof. 1.4. “Electronic distribution mechanism” means a mechanism generally accepted in the software development community for the electronic transfer of data. 1.5. “Executable” means covered code in any form other than source code. 1.6. “Initial developer” means the individual or entity identified as the initial Developer in the Source Code notice required by exhibit A. 1.7. “Larger work” means a work which combines covered code or portions thereof with code not governed by the terms of this License. 1.8. “License” means this document. APPENDIX 1.8.1. “Licensable” means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein. 1.9. “Modifications” means any addition to or deletion from the substance or structure of either the original code or any previous modifications. When covered code is released as a series of files, a modification is: A. Any addition to or deletion from the contents of a file containing original code or previous modifications. B. Any new file that contains any part of the original code or previous modifications. 1.10. “Original code” means source code of computer software 144 1.10.1.“Patent claims” means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent licensable by grantor. 1.11. “Source code” means the preferred form of the covered code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an executable, or source code differential comparisons against either the original code or another well known, available covered code of the contributor's choice. The source code can be in a compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge. 1.12. “You” (or “Your”) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this license or a future version of this license issued under section 6.1. For legal entities, “You” includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition, “control” means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity. 2. Source Code License. 2.1. The initial developer grant. The initial developer hereby grants You a world-wide, royalty-free, non-exclusive license, subject to third party intellectual property claims: a) under intellectual property rights (other than patent or trademark) licensable by initial developer to use, reproduce, modify, display, perform, sublicense and distribute the original code (or portions thereof) with or without modifications, and/or as part of a larger work; and (b) under patents claims infringed by the making, using or selling of original code, to make, have made, use, practice, sell, and offer for sale, and/or otherwise dispose of the original code (or portions there of). (c) the licenses granted in this section 2.1(a) and (b) are effective on the date Initial developer first distributes original code under the terms of this license. (d) Notwithstanding section 2.1(b) above, no patent license is granted: 1) for code that You delete from the original Code; 2) separate from the original code; or 3) for infringements caused by: i) the modification of the original code or ii) the combination of the original code with other software or devices. 2.2. Availability of source code. Any modification which you create or to which you contribute must be made available in source code form under the terms of this license either on the same media as an executable version or via an accepted electronic distribution mechanism to anyone to whom you made an executable version available; and if made available via electronic distribution mechanism, must remain available for at least twelve (12) months after the date it initially became available, or at least six (6) months after a subsequent version of that particular modification has been made available to such recipients. You are responsible for ensuring that the source code version remains available even if the electronic distribution mechanism is maintained by a third party. 3.3. Description of modifications. You must cause all covered code to which you contribute to contain a file documenting the changes You made to create that covered code and the date of any change. You must include a prominent statement that the modification is derived, directly or indirectly, from original code provided by the initial developer and including the name of the initial developer in (a) the source code, and (b) in any notice in an executable version or related documentation in which you describe the origin or ownership of the covered code. 3.4. Intellectual property matters (a) Third party claims. If contributor has knowledge that a license under a third party's intellectual property rights is required to exercise the rights granted by such contributor under sections 2.1 or 2.2, contributor must include a text file with the source code distribution titled "LEGAL" which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If contributor obtains such knowledge after the modification is made available as described in section 3.2, contributor shall promptly modify the LEGAL file in all copies contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the covered code that new knowledge has been obtained. (b) Contributor APIs. If contributor's modifications include an application programming interface and contributor has knowledge of patent licenses which are reasonably necessary to implement that API, contributor must also include this information in the LEGAL file. 3. Distribution Obligations. Application of license. The modifications which You create or to which you contribute are governed by the terms of this license, including without limitation section 2.2. The source code version of covered code may be distributed only under the terms of this license or a future version of this license released under section 6.1, and you must include a copy of this license with every copy of the source code you distribute. APPENDIX 3.2. Contributor Grant. Subject to third party intellectual property claims, each contributor hereby grants You a world-wide, royalty-free, non-exclusive license (a) under intellectual property rights (other than patent or trademark) licensable by contributor, to use, reproduce, modify, display, perform, sublicense and distribute the modifications created by such contributor (or portions thereof) either on an unmodified basis, with other modifications, as covered code and/or as part of a larger work; and (b) under patent claims infringed by the making, using, or selling of modifications made by that contributor either alone and/or in combination with its contributor version (or portions of such combination), to make, use, sell, offer for sale, have made, and/or otherwise dispose of: 1) modifications made by that contributor (or portions thereof); and 2) the combination of modifications made by that contributor with its contributor version (or portions of such combination). (c) the licenses granted in sections 2.2(a) and 2.2(b) are effective on the date contributor first makes commercial use of the covered code. (d) Notwithstanding section 2.2(b) above, no patent license is granted: 1) for any code that contributor has deleted from the contributor version; 2) separate from the contributor version; 3) for infringements caused by: i) third party modifications of contributor version or ii) the combination of modifications made by that contributor with other software (except as part of the contributor version) or other devices; or 4) under patent claims infringed by covered code in the absence of modifications made by that contributor. 3.1. You may not offer or impose any terms on any source code version that alters or restricts the applicable version of this license or the recipients' rights hereunder. However, you may include an additional document offering the additional rights described in section 3.5. 145 APPENDIX 3.5. 3.6. APPENDIX 146 (c) Representations. contributor represents that, except as disclosed pursuant to section 3.4(a) above, contributor believes that contributor's modifications are contributor's original creation(s) and/or contributor has sufficient rights to grant the rights conveyed by this license. 3.7. Required notices. You must duplicate the notice in exhibit A in each file of the source code. If it is not possible to put such notice in a particular source code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more modification(s), you may add your name as a contributor to the notice described in exhibit A. you must also duplicate this license in any documentation for the source code where You describe recipients' rights or ownership rights relating to covered code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of covered code. However, you may do so only on your own behalf, and not on behalf of the Initial developer or any contributor. You must make it absolutely clear than any such warranty, support, indemnity or liability obligation is offered by you alone, and You hereby agree to indemnify the Initial developer and every contributor for any liability incurred by the Initial developer or such contributor as a result of warranty, support, indemnity or liability terms you offer. 4. Inability to comply due to statute or regulation. If it is impossible for you to comply with any of the terms of this license with respect to some or all of the covered code due to statute, judicial order, or regulation then you must: (a) comply with the terms of this license to the maximum extent possible; and (b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in section 3.4 and must be included with all distributions of the source code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. Distribution of executable versions. You may distribute covered code in executable form only if the requirements of section 3.1-3.5 have been met for that covered code, and if you include a notice stating that the source code version of the covered code is available under the terms of this license, including a description of how and where you have fulfilled the obligations of section 3.2. The notice must be conspicuously included in any notice in an executable version, related documentation or collateral in which you describe recipients' rights relating to the covered code. You may distribute the executable version of covered code or ownership rights under a license of your choice, which may contain terms different from this license, provided that you are in compliance with the terms of this license and that the license for the executable version does not attempt to limit or alter the recipient's rights in the source code version from the rights set forth in this license. If you distribute the executable version under a different license you must make it absolutely clear that any terms which differ from this license are offered by you alone, not by the Initial developer or any contributor. You hereby agree to indemnify the initial developer and every contributor for any liability incurred by the initial developer or such contributor as a result of any such terms You offer. Larger works. You may create a larger work by combining covered code with other code not governed by the terms of this license and distribute the larger work as a single product. In such a case, you must make sure the requirements of this license are fulfilled for the covered code. 5. Application of this license. This license applies to code to which the initial developer has attached the notice in exhibit A and to related covered code. 6. Versions of the license. 6.1. New versions. Netscape communications corporation (“Netscape”) may publish revised and/or new versions of the license from time to time. Each version will be given a distinguishing version number. 6.2. Effect of new versions. Once covered code has been published under a particular version of the license, you may always continue to use it under the terms of that version. You may also choose to use such covered code under the terms of any subsequent version of the license published by netscape. No one other than netscape has the right to modify the terms applicable to covered code created under this license. 6.3. Derivative works. If You create or use a modified version of this license (which you may only do in order to apply it to code which is not already covered code governed by this license), You must (a) rename Your license so that the phrases "Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL", "NPL" or any confusingly similar phrase do not appear in your license (except to note that your license differs from this license) and (b) otherwise make it clear that Your version of the license contains terms which differ from the Mozilla Public license and netscape Public License. (Filling in the name of the initial developer, original code or contributor in the notice described in exhibit A shall not of themselves be deemed to be modifications of this license.) 7. DISCLAIMER OF WARRANTY. COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES THAT THE COVERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT FOR A PARTICULAR PURPOSE OR NON-INFRINGING. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE COVERED CODE IS WITH YOU. SHOULD ANY COVERED CODE PROVE DEFECTIVE IN ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR ANY OTHER CONTRIBUTOR) ASSUME THE COST OF ANY NECESSARY SERVICING, REPAIR OR CORRECTION. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER. 8. TERMINATION. 8.1. 8.2. This license and the rights granted hereunder will terminate automatically if you fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the covered code which are properly granted shall survive any termination of this license. Provisions which, by their nature, must remain in effect beyond the termination of this license shall survive. If you initiate litigation by asserting a patent infringement claim (excluding declatory judgment actions) against initial developer or a contributor (the initial developer or contributor against whom you file such action is referred to as “Participant”) alleging that: 8.3. If you assert a patent infringement claim against participant alleging that such participant's contributor version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such participant under sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license. 8.4. In the event of termination under sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination. 9. LIMITATION OF LIABILITY. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. APPENDIX (a) such participant's contributor version directly or indirectly infringes any patent, then any and all rights granted by such participant to you under sections 2.1 and/or 2.2 of this license shall, upon 60 days notice from Participant terminate prospectively, unless if within 60 days after receipt of notice you either: (i) agree in writing to pay participant a mutually agreeable reasonable royalty for your past and future use of modifications made by such participant, or (ii) withdraw your litigation claim with respect to the contributor version against such participant. If within 60 days of notice, a reasonable royalty and payment arrangement are not mutually agreed upon in writing by the parties or the litigation claim is not withdrawn, the rights granted by participant to you under sections 2.1 and/or 2.2 automatically terminate at the expiration of the 60 day notice period specified above. (b) any software, hardware, or device, other than such participant's contributor Version, directly or indirectly infringes any patent, then any rights granted to You by such participant under sections 2.1(b) and 2.2(b) are revoked effective as of the date you first made, used, sold, distributed, or had made, modifications made by that participant. 10. U.S. GOVERNMENT END USERS. The covered code is a "commercial item," as that term is defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of "commercial computer software" and "commercial computer software documentation," as such terms are used in 48 C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R. 12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4 (June 1995), all U.S. Government end users acquire covered code with only those rights set forth herein. 147 APPENDIX 11. MISCELLANEOUS. This license represents the complete agreement concerning subject matter hereof. If any provision of this license is held to be unenforceable, such provision shall be reformed only to the extent necessary to make it enforceable. This License shall be governed by California law provisions (except to the extent applicable law, if any, provides otherwise), excluding its conflict-of-law provisions. With respect to disputes in which at least one party is a citizen of, or an entity chartered or registered to do business in the united states of america, any litigation relating to this License shall be subject to the jurisdiction of the federal courts of the northern district of california, with venue lying in santa clara county, california, with the losing party responsible for costs, including without limitation, court costs and reasonable attorneys' fees and expenses. The application of the united nations convention on contracts for the International sale of goods is expressly excluded. Any law or regulation which provides that the language of a contract shall be construed against the drafter shall not apply to this license. EXHIBIT A -Mozilla Public License. 12. RESPONSIBILITY FOR CLAIMS. As between initial developer and the contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this license and you agree to work with initial developer and contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability. Alternatively, the contents of this file may be used under the terms of the _____ license (the "[___] License"), in which case the provisions of [______] license are applicable instead of those above. If you wish to allow use of your version of this file only under the terms of the [____] license and not to allow others to use your version of this file under the MPL, indicate your decision by deleting the provisions above and replace them with the notice and other provisions required by the [___] license. If you do not delete the provisions above, a recipient may use your version of this file under either the MPL or the [___] license." 13. MULTIPLE-LICENSED CODE. Initial developer may designate portions of the covered code as "Multiple-Licensed". "Multiple-Licensed" means that the initial developer permits you to utilize portions of the covered code under your choice of the NPL or the alternative licenses, if any, specified by the initial developer in the file described in exhibit A. APPENDIX 148 The contents of this file are subject to the Mozilla Public License Version 1.1 (the “license”); you may not use this file except in compliance with the License. You may obtain a copy of the license at http://www.mozilla.org/MPL/ Software distributed under the license is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY KIND, either express or implied. See the license for the specific language governing rights and limitations under the License. The Original Code is ______________________________________. The Initial Developer of the Original Code is___________________. Portions created by ______________________ are Copyright (C) _______________________. All Rights Reserved. Contributor(s): ______________________________________. NOTE: The text of this exhibit A may differ slightly from the text of the notices in the source code files of the original code. You should use the text of this exhibit A rather than the text found in the original code/source code for Your modifications. APPENDIX 149 APPENDIX APPENDIX 150 The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. MODEL 1-800-243-0000 USA, Consumer User 1-888-865-3026 USA, Commercial User 1-888-542-2623 CANADA SERIAL LG Customer Information Center This product qualifies for ENERGY STAR in the “factory default” setting. Changing the factory default settings or enabling other features may increase power consumption that could exceed the limits necessary to quality for ENERGY STAR.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes XMP Toolkit : 3.1-701 Producer : Acrobat Distiller 7.0 (Windows) Create Date : 2010:07:28 08:48:37+09:00 Modify Date : 2010:07:28 08:48:37+09:00 Metadata Date : 2010:07:28 08:48:32+09:00 Creator Tool : PScript5.dll Version 5.2 Document ID : uuid:30D39676D999DF118805C0AC8AECF5E5 Instance ID : uuid:84a4568a-2254-421a-9cfc-2cb50c036393 Derived From Instance ID : uuid:1385570e-90ce-4e10-9d10-b24e871c67af Derived From Document ID : uuid:dfece702-adfa-4846-bd59-98c7461bec71 Format : application/postscript Creator : sun Title : SAC34134301-Edit1 Page Count : 77 Author : sunEXIF Metadata provided by EXIF.tools