LG Electronics USA 37LG500HUA LCD TV MONITOR User Manual User s Manual H ok
LG Electronics USA LCD TV MONITOR User s Manual H ok
USERS MANUAL
Order Number : GETEC-C1-09-009 Test Report Number : GETEC-E3-09-010 APPENDIX H : USER’S MANUAL EUT Type: LCD TV/Monitor FCC ID.: BEJ37LG500HUA FCC Class B Certification LCD TV PLASMA TV OWNER’S MANUAL LCD TV MODELS 32LC5DC 32LC50CS 32LC5DCS 32LC50CB 32LX50C 32LC5DCB 37LC5DC 32LX50CS 37LC50C 37LC5DCB 37LC5DC1 37LC50CB 42LC5DC 42LB50C 42LC50C 32LX5DC 32LX5DCS 32LG500H 37LG500H 42LB5DC 42LG500H 32LC50C PLASMA TV MODEL 42PX8DC 42PG65C 42PG60C Please read this manual carefully before operating your set. Retain it for future reference. Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service. www.lgcommercial.com WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product SAFETY INSTRUCTION IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lighting storms or when unused for long periods of time. 10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. SAFETY INSTRUCTION 11 Never touch this apparatus or antenna during a thunder or lighting storm. 12 When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. 13 Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. 14 CAUTION concerning the Power Cord : It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV. 15 WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 16 Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit). 17 GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock. (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grouned AC outlet) If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. 19 Keep the product away from direct sunlight. 20 ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70 Ground Clamp Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. 22 Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. 23 Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places. 24 If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center. 25 Do not press strongly upon the panel with a hand or sharp object such as nail, pencil or pen, or make a scratch on it. Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Electric Service Equipment 21 Grounding Conductors (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC: National Electrical Code FEATURES OF THIS TV On Disposal a. The fluorescent lamp used in this product contains a small amount of mercury. b. Do not dispose of this product with general household waste. c. Disposal of this product must be carried out in accordance to the regulations of your local authority. FOR LCD TV PREPARATION If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the monitor's performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen. PREPARATION ACCESSORIES Ensure that the following accessories are included with your product. If an accessory is missing, please contact the dealer where you purchased the product. User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard compliance for the product. PU TV T INP MU PIP EZ LT UT PO WE MO TV DE DV TV PIP PIC CH PO VC STEZ SOU - PIP W B ND CH ER RA + PIP TIO SW INPUDV AP T D INF CC VCO INP UT INP TV CC XIT INP ME ENNU RA TE TIO SA RE TURN ENTE ME NU MU LT PIC TIM IT PIP CH PIP PIP SA SWA CD Manual PIP INPU RA TIO SA EN TER VO TIM ER CH MU TE PAG 1.5V 1.5V CH DE ME NU or FLASHB http://www.lgusa.com www.lg.ca PIP Owner’s Manual, Setup & Operation Guide for Commercial Mode Copyright© 2007 LGE, All Rights Reserved. CHE TE MO VC PIP CH + PIP SW INPU AP INF CC EX PAG MU TV ER CH Owner's Manual PO WE CH ND LCD TV PLASMA TV UT DV PIP EZ SOU INFO VO UT PIP EZ FLAS BACK H Remote Control, Batteries Power Cord * Slightly wipe stained spot on the exterior only with the polishing cloth for the product exterior if there is stain or fingerprint on surface of the exterior. Polishing Cloth This feature is not available for all models. * Do not wipe roughly when removing stain. Please be cautions of that excessive pressure may cause scratch or discoloration. PREPARATION LCD TV model only Option Extras x2 M4xL22 Torx plus Star head screw (Refer to p.7, 15) Protective Bracket and Bolt for Power Cord PREPARATION (This feature is not available for all models.) D-sub 15 pin Cable (Refer to P.12-13, 15) Only 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C models Cable Holder 1-Bolt for fixing the Cable Management Cable Holder (Refer to p.12) (Refer to p.12-13) (Refer to p.12-13) 4-Bolts for stand assembly (Refer to p.16) Only 32/37LC5DC*, 32/37LC50C* models Only 32/37/42LG500H models x4 or x4 Bolts for stand assembly Screw for stand fixing Protection Cover (Refer to P.15) (Refer to P.19) Cable Holder Plasma TV models only 75 ohm Round Cable (Except 42PG60C/65C) D-sub 15 Pin Cable (Except 42PG60C/65C) Only 42PG65C model x4 Cable Management Clip Bolts for stand assembly (Refer to P.14) Cable Holder (Except 42PX8DC) Plug in type holder FRONT PANEL CONTROLS ■ Here shown may be somewhat different from your TV. 32/37/42LC5DC*,32/37/42LC50C*, 42LB5DC, 42LB50C PREPARATION CH CHANNEL Buttons VOL VOLUME Buttons ENTER ENTER Button MENU MENU Button INPUT INPUT Button POWER Button Remote Control Sensor Power/Standby Indicator Illuminates red when the TV is in standby mode. Illuminates green when the TV is switched on. x4 Tighten the stand with the four screws (provided as parts of the TV). or x2 Tighten the two of these four screws and x 2 the two Torx plus star head screws (provided as parts of the TV) to secure the TV. Tighten the two Torx plus star head screws with a star head driver bit (not provided as parts of the TV). PREPARATION 32LX5DC*, 32LX50C* PREPARATION Remote Control Sensor Power/Standby Indicator Illuminates red when the TV is in standby mode. Illuminates green when the TV is switched on. CH VOL ENTER MENU INPUT ON/OFF ON/OFF Button INPUT Button MENU Button ENTER Button VOLUME Buttons CHANNEL Buttons 32/37/42LG500H CH Intelligent Sensor Adjusts picture according to the surrounding conditions Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on. VOL CHANNEL Buttons VOLUME Buttons ENTER ENTER Button MENU MENU Button INPUT INPUT Button Remote Control Sensor POWER Button 42PX8DC INPUT ENTER PREPARATION This TV’s stand is sold, separately. INPUT Remote Control Sensor Power/Standby Indicator Illuminates red when the TV is in standby mode. Illuminates green when the TV is switched on. MENU ENTER VOL CH POWER Button INPUT Button MENU Button ENTER Button VOLUME Buttons CHANNEL Buttons 42PG60C, 42PG65C Remote Control Sensor POWER Button Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the set is switched on. INPUT ENTER S t a n d (Only 42PG65C model) INPUT INPUT MENU INPUT Button MENU VOL ENTER MENU INPUT ENTER ENTER MENU Button VOL VOL ENTER Button CH CH CH VOLUME (-,+) Buttons CHANNEL (E, D) Buttons PREPARATION BACK PANEL INFORMATION Here shown may be somewhat different from your TV. 32/37/42LC5DC*,32/37/42LC50C*, 42LB5DC, 42LB50C 32LX5DC*, 32LX50C* 42PX8DC S-VIDEO R AUDIO RL/MONO VIDEO S-VIDEO AV IN 2 ANTENNA IN AV IN 2 11 11 M.P.I. 42PG60C, 42PG65C NTENNA IN S-VIDEO VIDEO OR VIDEO L/MONO AUDIO PREPARATION 11 AV IN 2 O R L/MONO AUDIO ■ 32/37/42LG500H M.P.I. S-VIDEO VIDEO L/MONO AUDIO R AV IN 2 AV IN 2 11 11 ANTENNA IN M.P.I. 13 12 ANTENNA IN M.P.I. 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C, 32LX5DC*, 32LX50C*, 42PX8DC DIGITAL AUDIO OUT (OPTICAL) HDMI/DVI IN RESET SERVICE ONLY M.P.I. UPDATE REMOTE CONTROL OUT RGB IN 10 RJP INTERFACE VIDEO COMPONENT IN 1(DVI) 10 VIDEO L/MONO AUDIO R S-VIDEO AUDIO S-VIDEO (MONO) AUDIO AV IN 1 VIDEO SPEAKER OUT AUDIO IN 42PG60C, 42PG65C 10 RGB IN DIGITAL AUDIO OUT RJP SPEAKER INTERFACE OUT AUDIO (RGB / DVI) RGB(PC) REMOTE CONTROL OUT OPTICAL SERVICE ONLY COMPONENT IN DVI IN AUDIO VIDEO AUDIO S-VIDEO VIDEO L (MONO) PREPARATION UPDATE RESET AV IN 1 HDMI IN 32/37/42LG500H OPTICAL DIGITAL SPEAKER OUT AUDIO OUT HDMI/DVI IN RESET RGB IN 1(DVI) RGB(PC) UPDATE AUDIO (RGB/DVI) RS-232C IN (SERVICE ONLY) AV IN 1 RJP INTERFACE AUDIO VIDEO 10 COMPONENT IN S-VIDEO HDMI/DVI IN, HDMI IN Connect a HDMI (DVI) connection to either input. DIGITAL AUDIO OUT Connect digital audio from various types of equipment. Note: In standby mode, these ports do not work. 3 13 REMOTE CONTROL OUT AUDIO L/MONO VIDEO AV (Audio/Video) IN Connect audio/video output from an external device to these jacks. S-VIDEO Connect S-Video out from an S-VIDEO device. COMPONENT IN Connect a component video/audio device to these jacks. M.P.I RESET/UPDATE/REMOTE CONTROL OUT 10 RJP INTERFACE SERVICE ONLY 11 RGB IN (PC) Connect the output from a PC. AUDIO IN (RGB, DVI) Connect the audio from a PC or DTV. Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. 12 ANTENNA IN Connect over-the air signals to this jack. SPEAKER OUT 8Ω 11 PREPARATION STAND INSTALLATION 32/37LC5DC*, 32/37LC50C* Carefully place the product screen side down on a cushioned surface that will protect product and screen from damage. Assemble the product stand with the product as shown. PREPARATION 16 42PG65C Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. NOTE After inserting the MPI slot/card, install the product stand. Assemble the product stand with the product as shown. Tighten the 4 bolts securely using the holes in the back of the TV. Securely install the 4 bolts provided as shown below. ATTACHING THE TV TO A WALL This feature is not available for all models. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. ■ PREPARATION ■ Insert the TV brackets (or eye-bolts) and bolts to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) on the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. ■ Use a sturdy rope (not provided as parts of the product, must purchase separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. SWIVEL STAND 20° (37LC5DC1, 42LC5DC, 42LC50C, 42PX8DC, 42LB5DC, 42LB50C, 42PG65C models) 90° (32LX5DC/S, 32LX50C/S, 32LC5DC/S, 32LC50C/S, 37LC5DC, 37LC50C, 32/37/42LG500H models) The TV can be conveniently swivelled on its stand 20°or 90° to the left or right to provide the optimum viewing angle. 17 PREPARATION ATTACHING THE TV TO A DESK ■ Here shown may be somewhat different from your TV. The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing injury or damaging the product. 10 mm) * S c r e w s - M 5 x L ( t a b l e d e p t h + 8~1 ex) table depth-15mm: Bolts - M5 x 25 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C PREPARATION Stand 4-Screws (not provided as parts of the product) Desk 32LX5DC*, 32LX50C* Stand 4-Screws (not provided as parts of the product) 42PX8DC Stand 2-Screws (not provided as parts of the product) 42PG65C Stand 4-Screws (not provided as parts of the product) Desk 32/37/42LG500H Stand 4-Screws (not provided as parts of the product) 18 Desk 32/37/42LG500H Stand 1-Screw (provided as parts of the product) Desk PREPARATION WARNING To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation instructions. Tipping, shaking, or rocking the machine may cause injury. VESA WALL MOUNTING This product accepts a VESA-compliant mounting interface pad. (optional) There 4 threaded holes are available for attaching the bracket. ■ This feature is not available for all models. Model VESA (A * B) 32LC5DC*, 32LC50C*, 32LX5DC*, 32LX50C*, 32LG500H 200 * 100 37LG500H, 42LG500H 200 * 200 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C 600 * 400 42PG60C 400 * 400 42PX8DC 600 * 400 Product LCD TV PLASMA TV NOTE Screw length needed depends on the wall mount used. For further information, refer to the VESA Wall Mounting Instruction Guide. DESKTOP PEDESTAL INSTALLATION For proper ventilation, allow a clearance of 4inches on each side from the wall. ■ Image shown may differ from your TV. ■ This feature is not available for all models. 4 inches 4 inches 4 inches 4 inches CAUTION Ensure adequate ventilation by following the clearance recommendations. 19 PREPARATION ANTENNA OR CABLE CONNECTION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections. For optimum picture quality, adjust antenna direction if needed. PREPARATION Multi-family Dwellings/Apartments (Connect to wall antenna socket) Wall Antenna Socket ANTENNA IN M.P.I. RF Coaxial Wire (75 ohm) Outdoor Antenna (VHF, UHF) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Copper Wire Be careful not to bend the bronze wire when connecting the antenna. 2. Cable ANTENNA IN M.P.I. Cable TV Wall Jack RF Coaxial Wire (75 ohm) ANTENNA IN UHF M.P.I. Signal Amplifier Antenna VHF To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter. ■ If the antenna is not installed properly, contact your dealer for assistance. ■ ■ NOTE 20 The TV will let you know when the analog, cable, and digital channel scans are complete. EXTERNAL EQUIPMENT SETUP ■ ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. This part of external equipment setup mainly use picture for LCD TV(Except 32/37/42LG500H) models. HD RECEIVER SETUP This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. When connecting Component cable EXTERNAL EQUIPMENT SETUP 1. How to connect Connect the video outputs (Y, PB, PR) of the digital set top box to the C O M P O N E N T I N V I D E O jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). PB PR DIGITAL AUDIO OUT (OPTICAL) HDMI/DVI IN ■ ■ M.P.I. 1(DVI) 2. How to use Connect the audio output of the digital set-top box to the C O M P O N E N T I N A U D I O jacks on the set. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select C o m p o n e n t input source with using the I N P U T button on the remote control. Signal Component HDMI1/DVI, HDMI2 480i Yes No 480p Yes Yes 720p Yes Yes 1080i Yes Yes 1080p Yes Yes RJP RFACE VIDEO AUDIO S-VIDEO COMPONENT IN * 42LB5DC, 42LB50C model only 21 EXTERNAL EQUIPMENT SETUP When connecting HDMI cable 1. How to connect EXTERNAL EQUIPMENT SETUP Connect the digital set-top box to H D M I / D V I I N 1 ( D V I ) or 2 jack on the set. No separated audio connection is necessary. HDMI supports both audio and video. HDMI/DVI IN M.P.I 1(DVI) 2. How to use ■ ■ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) VIDEO RJP INTERFACE Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control. COMPONENT IN NOTE If the device does not support Auto HDMI, you need to set the output resolution appropriately. HDMI-DTV OUTPUT 22 DIGITAL AUDIO OUT (OPTICAL) AUDIO When connecting HDMI to DVI cable DIGITAL AUDIO OUT (OPTICAL) HDMI/DVI IN RESET SERVICE ONLY M.P.I. 1(DVI) UPDATE REMOTE CONTROL OUT RGB IN VIDEO RJP INTERFACE AUDIO COMPONENT IN S-VIDEO (MONO) AUDIO AV IN 1 VIDEO SPEAKER AUDIO IN OUT (RGB, DVI) DVI-DTV OUTPUT EXTERNAL EQUIPMENT SETUP 1. How to connect Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1 ( D V I ) or 2 jack on the set. Connect the audio output of the digital set-top box to the A U D I O I N ( R G B , D V I ) jack on the set. 2. How to use ■ Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ■ Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control. 23 EXTERNAL EQUIPMENT SETUP DVD SETUP When connecting Component cable 1. How to connect EXTERNAL EQUIPMENT SETUP Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O jacks on the set. Match the jack colors (Y = green, PB = blue, and PR = red). Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O jacks on the set. 2. How to use PB PR ■ Select C o m p o n e n t input source with using the I N P U T button on the remote control. DIGITAL AUDIO OUT (OPTICAL) RJP ERFACE VIDEO AUDIO COMPONENT IN Refer to the DVD player's manual for operating instructions. Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player 24 PB PR PB PR B-Y R-Y Cb Cr Pb Pr M.P.I. 1(DVI) Turn on the DVD player, insert a DVD. HDMI/DVI IN ■ ■ S-VIDEO When connecting with an S-Video cable AUDIO 1. How to connect Connect the S-VIDEO output of the DVD to the S - V I D E O input on the set. Connect the audio outputs of the DVD to the A U D I O input jacks on the set. ■ Turn on the DVD player, insert a DVD. ■ ■ Select A V 1 input source with using the I N P U T button on the remote control. If connected to A V I N 2, select A V 2 input source. ■ Refer to the DVD player's manual for operating instructions. GITAL UDIO OUT TICAL) RESET REMOTE CONTROL OUT M.P.I. UPDATE S-VIDEO AUDIO NT IN (MONO) VIDEO AUDIO AV IN 1 SPE When connecting HDMI cable 1. How to connect Connect the HDMI output of the DVD to the H D M I / D V I I N 1 ( D V I ) or 2 jack on the set. No separated audio connection is necessary. HDMI supports both audio and video. DIGITAL AUDIO OUT (OPTICAL) HDMI/DVI IN 2. How to use ■ Select H D M I 1 / D V I or H D M I 2 input source with using the I N P U T button on the remote control. ■ Refer to the DVD player's manual for operating instructions. EXTERNAL EQUIPMENT SETUP 2. How to use S-VIDEO M.P.I 1(DVI) VIDEO RJP INTERFACE AUDIO COMPONENT IN NOTE If the device does not support Auto HDMI, you need to set the output resolution appropriately. HDMI-DVD OUTPUT 25 EXTERNAL EQUIPMENT SETUP VCR SETUP To avoid picture noise (interference), leave an adequate distance between the VCR and TV. ■ Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period of time. (Only Plasma TV model). If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. This phenomenon is common to all manufactures and in consequence the manufactures warranty does not cover the product bearing this phenomenon. ■ When connecting with an antenna EXTERNAL EQUIPMENT SETUP ANTENNA IN M.P.I. M.P .I. S-VIDEO VIDEO ANT OUT ANT IN OUTPUT SWITCH Wall Jack Antenna 1. How to connect Connect the RF antenna out socket of the VCR to the A n t e n n a socket on the set. Connect the antenna cable to the RF antenna in socket of the VCR. 2. How to use 26 ■ Set VCR output switch to 3 or 4 and then tune TV to the same channel number. ■ Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) ( ANT IN S-VIDEO ANT OUT OUTPUT SWITCH When connecting with a RCA cable 1. How to connect V I D E O jacks between TV and Connect the A U D I O/V VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) M.P.I. TAL DIO UT CAL) VIDEO RESET SERV REMOTE CONTROL OUT M.P.I. UPDATE ■ Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) (MONO) S-VIDEO AUDIO VIDEO AUDIO T IN AV IN 1 Select A V 1 input source with using the I N P U T button on the remote control. ■ If connected to A V I N 2, select A V 2 input source. SPEAKE OUT ■ NOTE If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L / M O N O jack of the set. EXTERNAL EQUIPMENT SETUP 2. How to use When connecting with an S-Video cable 1. How to connect ANT IN S-VIDEO ANT OUT OUTPUT SWITCH VIDEO M.P.I. Connect the S-VIDEO output of the VCR to the S - V I D E O input on the set. Connect the audio outputs of the VCR to the A U D I O input jacks on the set. RESET SER M.P.I. 2. How to use ■ GITAL AUDIO OUT PTICAL) UPDATE Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) AUDIO ■ Select A V 1 input source with using the I N P U T button on the remote control. ■ If connected to A V I N 2, select A V 2 input source. ENT IN The picture quality is improved: compared to normal composite (RCA cable) input. (MONO) AUDIO AV IN 1 VIDEO SPEAK OUT CAUTION NOTE S-VIDEO REMOTE CONTROL OUT Do not connect to both Video and S-Video at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work. 27 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP Camcorder 1. How to connect Video Game Set V I D E O jacks Connect the A U D I O/V between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red) VIDEO ■ Select A V 2 input source with using the I N P U T button on the remote control. ■ If connected to A V I N 1 input, select A V 1 input source. ■ Operate the corresponding external equipment. S-VIDEO VIDEO L/MONO AUDIO R EXTERNAL EQUIPMENT SETUP 2. How to use AV IN 2 DIGITAL AUDIO OUTPUT i.e) 32/37/42LC5DC*, 32/37/42LC50C*, 42LB5DC, 42LB50C Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port. 1. How to connect Connect one end of an optical cable to the TV Digital Audio (Optical) Output port. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. DIGITAL AUDIO OUT (OPTICAL) HDMI/DVI IN Set the “TV Speaker option - Off” in the AUDIO menu. (G p . 5 8). See the external audio equipment instruction manual for operation. NOTE When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (G p . 5 8) CAUTION 28 Do not look into the optical output port. Looking at the laser beam may damage your vision. M.P.I. 1(DVI) RJP NTERFACE VIDEO AUDIO COMPONENT IN S-V PC SETUP This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. When connecting D-sub 15pin cable SERVICE ONLY 1. How to connect REMOTE CONTROL OUT ATE RGB IN (MONO) VIDEO AUDIO IN (RGB, DVI) SPEAKER OUT AUDIO AV IN 1 EXTERNAL EQUIPMENT SETUP Connect the RGB output of the PC to the R G B I N jack on the set. Connect the PC audio output to the A U D I O I N ( R G B , D V I ) jack on the set. 2. How to use ■ Turn on the PC and the set. ■ Select R G B - P C input source with using the I N P U T button on the remote control. When connecting HDMI to DVI cable RGB OUTPUT AUDIO 1. How to connect Connect the DVI output of the PC to the H D M I / D V I I N 1 ( D V I ) jack on the set. DIGITA AUDIO OUT (OPTICA VICE ONLY HDMI/DVI IN 1(DVI) RGB IN Connect the PC audio output to the A U D I O I N ( R G B / D V I) jack on the set. ER VIDEO RJP INTERFACE COMPONENT AUDIO IN (RGB, DVI) 2. How to use ■ Turn on the PC and the set ■ Select H D M I 1 / D V I input source with using the I N P U T button on the remote control. DVI-PC OUTPUT AUDIO 29 EXTERNAL EQUIPMENT SETUP NOTES Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the EXTERNAL EQUIPMENT SETUP Supported Display Specifications (RGB/HDMI1-PC) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 640x350 31.469 70.08 640x480 31.469 37.861 37.500 59.94 72.80 75.00 800x600 35.156 37.879 48.077 46.875 56.25 60.31 72.18 75.00 1024x768 48.363 56.476 60.023 60.00 70.06 75.02 1280x768 47.700 60.00 1360x768 47.720 59.799 1366x768 47.130 59.658 PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the screen. The synchronization input form for Horizontal and Vertical frequencies is separate. Supported Display Specifications (HDMI2-DTV) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480 31.500 31.469 60.00 59.94 1280x720 44.960 45.000 59.94 60.00 1920x1080i 33.720 33.750 59.94 60.00 Supported Display Specifications (Y, CB /PB, CR /PR) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480 15.73 15.73 31.47 31.50 59.94 60.00 59.94 60.00 1280x720 44.96 45.00 59.94 60.00 1920x1080i 33.72 33.75 59.94 60.00 Supported Display Specifications (RGB/HDMI1-DTV) Resolution 720x480 Horizontal Frequency(KHz) Vertical Frequency(Hz) 31.50 60.00 31.47(HDMI1-DTV:31.469) 59.94 * RGB-DOS mode only: 640x350 1280x720 44.96 45.00 59.94 60.00 1920x1080i 33.72 33.75 59.94 60.00 * Except 42PG60C/65C models in HDMI1-PC mode. 30 * 42LB5DC, 42LB50C Supported Display Specifications (RGB/HDMI1-PC) Horizontal Frequency(KHz) Vertical Frequency(Hz) 31.469 70.08 640x480 31.469 37.861 37.500 Supported Display Specifications (HDMI2-DTV) Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480 31.500 31.469 60.00 59.94 59.94 72.80 75.00 1280x720 44.960 45.000 59.94 60.00 800x600 35.156 37.879 48.077 46.875 56.25 60.31 72.18 75.00 1920x1080 33.720 33.750 67.500 59.94 60.00 60.00 1024x768 48.363 56.476 60.023 60.00 70.06 75.02 1280x768 47.700 60.00 1360x768 47.720 59.799 1366x768 47.130 59.658 1280x1024 63.668 59.895 65.317 59.978 640x350 (RGB only) (RGB only) 1400x1050 (RGB only) 1600x1200 74.537 59.869 1920x1080 66.587 59.934 1920x1200 74.038 59.950 Supported Display Specifications (Y, CB /PB, CR /PR) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480 15.73 15.73 31.47 31.50 59.94 60.00 59.94 60.00 1280x720 44.96 45.00 59.94 60.00 1920x1080 33.72 33.75 67.50 59.94 60.00 60.00 EXTERNAL EQUIPMENT SETUP Resolution Resolution * RGB-DOS mode only: 640x350 Supported Display Specifications (RGB/HDMI1-DTV) Resolution 720x480 Horizontal Frequency(KHz) Vertical Frequency(Hz) 31.50 60.00 31.47(HDMI1-DTV:31.469) 59.94 1280x720 44.96 45.00 59.94 60.00 1920x1080 33.72 33.75 59.94 60.00 59.94 67.43(HDMI1-DTV:67.5) 31 WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT In AV 1-2, Component, RGB, HDMI1/DVI, and HDMI2 input sources, screen returns to the last TV channel. External input modes rotate in regular sequence: TV, AV1INPUT 2, Component, RGB, HDMI1/DVI and HDMI2. INPUT TV MODE TV POWER INPUT DVD MULTI VCR PIP CH - PIP CH + PIP INPUT PIP EZ PIC EZ SOUND INFO SWAP MULTI Selects: RGB,HDMI1/DVI, HDMI2 and Component input sources. WATCHING TV / CHANNEL CONTROL Adjusts brightness on screen. MENU EXIT RATIO SAP PIP CH +/- Changes the PIP channel. G p . 4 2 PIP INPUT Select the connected input source for the sub-picture. G p.41 ENTER Selects the factory preset picture depend on the viewing EZ PIC environment. p.45 TIMER EZ SOUND Selects the factory preset sound for type of program. p.55 SWAP(or PIP SWAP) Exchange the main/sub images. G p . 4 2 VCR/DVD Control video cassette recorders or DVD players. control buttons NUMBER button — (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. FLASH BACK Tune to the last channel viewed. 32 CC PIP Switches the sub picture Double Window or off mode. G p.41-42 CH PAGE VOL MUTE FLASH BACK (Only 42PG60C, 42PG65C, 32/37/42LG500H models) TV POWER DVD CC INPUT VCR STB RATIO MODE Select the remote’s operating mode: TV, DVD, VCR (or STB). RATIO Change the aspect ratio. p.43- 4 4 CC Select a closed caption. G p.62 (*In DTV/CADTV mode G p.63) THUMBSTICK Navigate the on-screen menus and adjust the system set(Up/Down/Left tings to your preference. ENTER /Right/ENTER) EXIT(or Clears all on-screen displays and returns to TV viewing RETURN) from any menu. MENU INFO i MENU Displays the main menu. INFO Display information at the top of the screen. TIMER CH VOL MUTE FLASHBK PIP PIP CH- VOLUME UP Increase/decrease the sound level. /DOWN TIMER Select the amount of time before your TV turns off automatically. G p .6 9 MUTE Switch the sound on or off. G p.34 CHANNEL Select available channels. UP/DOWN PAGE Move from one full set of screen information to the next one. UP/DOWN WATCHING TV / CHANNEL CONTROL RETURN SAP PIP CH+ PIP SWAP PIP INPUT Installing Batteries ■ Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). ■ Install two 1.5V AA batteries(or 1.5V AAA) Don’t mix old or used batteries with new ones. ■ Close cover. 33 MOVIE & TV RATING Movie Rating (MPAA) -for USA only Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. SETUP VIDEO After inputting the password, use the D or E or or button to choose M o v i e R a t i n g. AUDIO TIME OPTION Press the G or button and then use the D or E or or button to select G , P G, P G - 1 3, R , N C - 1 7 or X . ■ G (General audiences) ■ PG (Parental guidance suggested) ■ PG-13 (Parents strongly cautioned) ■ R (Restricted) ■ NC-17 (No one 17 and under admitted) ■ X (Adult only) ■ Blocking Off (Permits all programs) SCREEN Movie Rating TV Rating-Children TV Rating-General Downloadable Rating SETUP VIDEO AUDIO TIME OPTION SCREEN LOCK If you set PG-13: G and PG movies will be available, PG-13, R, NC-17 and X will be blocked. Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Aux. Block Downloadable Rating For USA SETUP VIDEO TIME OPTION SCREEN or Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General LOCK Aux. Block PG PG-13 NC-17 Blocking Off For Canada Lock System Set Password Block Channel TV Rating-English TV Rating-French Aux. Block Downloadable Rating Downloadable Rating button and then use the D or E or Press the G or or button to select D i m 0, D i m 1, D i m 2, or D i m 3. SETUP Press the or or VIDEO or button and then use the D or E button to select D 1 L 1, D 1 L 2, or D 1 L 3. AUDIO TIME OPTION Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. SCREEN LOCK Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Downloadable Rating Dim0 Dim1 Dim2 Dim3 PARENTAL CONTROL / RATING Downloadable Rating After inputting the password, use the D or E or button to choose D o w n l o a d a b l e R a t i n g. Block Channel Aux. Block AUDIO Set Password LOCK Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. Lock System Aux. Block Downloadable Rating G NOTE This function may become available in the future and will be available only for digital channel signal. This function operates only when TV has received Region5 Rating data. Based on rating table, your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. 77 PARENTAL CONTROL /RATINGS TV Rating Children -for USA only Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. SETUP VIDEO AUDIO TIME OPTION After inputting the password, use the D or E or button to choose T V R a t i n g - C h i l d r e n. SCREEN or Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General LOCK Aux. Block Downloadable Rating button and then use the D or E or Press the G or or button to select A g e, or F a n t a s y V i o l e n c e. button and then use the D or E or Press the G or or button to select block options. SETUP VIDEO AUDIO Age (applies to TV-Y, TV-Y7) ■ Fantasy Violence (applies to TV-Y7) ■ TIME OPTION SCREEN Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Age Fantasy Violence LOCK Aux. Block Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. Downloadable Rating TV Rating General -for USA only Based on the ratings, blocks certain TV programs that you and your family do not want to view. SETUP PARENTAL CONTROL / RATING After inputting the password, use the D or E or button to choose T V R a t i n g - G e n e r a l. VIDEO or AUDIO TIME OPTION button and then use the D or E or Press the G or or button to select A g e, D i a l o g u e, L a n g u a g e, S e x or V i o l e n c e. button and then use the D or E or Press the G or or button to select block options. Age (applies to TV-G,TV-PG,TV-14,TV-MA) ■ Dialogue-sexual dialogue (applies to TV-PG,TV-14) ■ Language-adult language (applies to TV-PG,TV-14,TV-MA) ■ Sex-sexual situations (applies to TV-PG,TV-14,TV-MA) ■ Violence (applies to TV-PG,TV-14,TV-MA) ■ SCREEN Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General LOCK Aux. Block Downloadable Rating SETUP VIDEO AUDIO TIME OPTION SCREEN Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General LOCK Aux. Block Lock System Downloadable Rating Age Dialogue Language Sex Violence 78 TV Rating English - for CANADA only Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. SETUP VIDEO AUDIO TIME OPTION After inputting the password, use the D or E or button to choose T V R a t i n g - E n g l i s h. or Set Password Block Channel TV Rating-English TV Rating-French Aux. Block LOCK Downloadable Rating Press the G or button and then use the D or E or or button to select E, C, C 8 +, G, P G, 1 4 +, 1 8 +, or Blocking Off. E(Exempt) C(Children) ■ C8+(Children eight years and older) ■ G(General programming, suitable for all audiences) ■ PG(Parental Guidance ) ■ 14+(Viewers 14 years and older) ■ 18+(Adult programming) ■ Blocking Off(Permits all programs) ■ SETUP VIDEO ■ SCREEN Lock System AUDIO TIME OPTION SCREEN Lock System Set Password Block Channel TV Rating-English TV Rating-French Aux. Block LOCK Downloadable Rating C8+ PG 14+ 18+ Blocking Off Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. TV Rating French - for CANADA only Based on the ratings, blocks certain TV programs that you and your family do not want to view. After inputting the password, use the D or E or button to choose T V R a t i n g - F r e n c h. or SETUP VIDEO AUDIO TIME button and then use the D or E or Press the G or or button to select E, G, 8 ans+, 13 ans+, 16 ans+, 18 ans+, or Blocking Off. ■ E(Exempt) ■ G(General) ■ 8 ans+(General-Not convenient for little children) ■ 13 ans+(Not convenient for children of 13 years and younger) ■ 16 ans+(Not convenient for children of 16 years and younger) ■ 18 ans+(This programs is only for adults) ■ Blocking Off(Permits all programs) OPTION SCREEN Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. Set Password Block Channel TV Rating-English TV Rating-French Aux. Block LOCK Downloadable Rating SETUP VIDEO AUDIO TIME OPTION SCREEN Lock System Set Password Block Channel TV Rating-English TV Rating-French Aux. Block LOCK Downloadable Rating Lock System PARENTAL CONTROL / RATING 8 ans+ 13 ans+ 16 ans+ 18 ans+ Blocking Off 79 APPENDIX TROUBLESHOOTING The operation does not work normally. Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. ■ Ensure that the batteries are installed with correct polarity (+ to +, - to -). ■ Ensure that the correct remote operating mode is set: TV, VCR etc. ■ Install new batteries. ■ The remote control doesn’t work Power is suddenly turned off Is the sleep timer set? ■ Check the power control settings. Power interrupted. ■ No broadcast on station tuned with Auto off activated. ■ The video function does not work. Check whether the product is turned on. Try another channel. The problem may be with the broadcast. ■ Is the power cord inserted into wall power outlet? ■ Check your antenna direction and/or location. ■ Test the wall power outlet, plug another product’s power cord into the outlet where the product’s power cord was plugged in. ■ ■ No picture &No sound Picture appears slowly after switching on ■ This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. Adjust Color in menu option. ■ Keep a sufficient distance between the product and the VCR. ■ Try another channel. The problem may be with the broadcast. ■ Are the video cables installed properly? ■ Activate any function to restore the brightness of the picture. ■ APPENDIX No or poor color or poor picture Horizontal/vertical bars or picture shaking ■ Check for local interference such as an electrical appliance or power tool. Station or cable product experiencing problems, tune to another station. Station signal is weak, reorient antenna to receive weaker station. ■ Check for sources of possible interference. ■ Poor reception on some channels Lines or streaks in pictures 80 ■ ■ Check antenna (Change the direction of the antenna). The audio function does not work. Press the VOL or VOLUME button. ■ Sound muted? Press MUTE button. ■ Try another channel. The problem may be with the broadcast. ■ Are the audio cables installed properly? ■ Picture OK & No sound No output from one of the speakers Unusual sound from inside the product ■ Adjust Balance in menu option. ■ A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. There is a problem in PC mode. (Only PC mode applied) The signal is out of range Vertical bar or stripe on background & Horizontal Noise & Incorrect position Adjust resolution, horizontal frequency, or vertical frequency. Check the input source. ■ Work the Auto configure or adjust clock, phase, or H/V position. (Option) ■ Check the signal cable. Reinstall the PC video card. ■ APPENDIX Screen color is unstable or single color ■ ■ 81 APPENDIX MAINTENANCE Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can enjoy your new TV. Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. ■ Please be sure not to use a wet cloth. ■ Extended Absence CAUTION If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. PRODUCT SPECIFICATIONS MODELS Dimensions (Width x Height x Depth) APPENDIX Weight 42PG65C (42PG65C-UA) 41.1 x 28.9 x12.1 inches 1044.4 x 735.4 x 308.0 mm With stand (Only 42PG65C) Without stand With stand (Only 42PG65C) Without stand MODELS 82 42PG60C (42PG60C-UA) 41.1 x 26.7x 3.1 inches 1044.4 x680.5x 79.6mm 41.1 x 26.7x 4.2 inches 1044.4 x680.5x 107.6mm 55.1 pounds / 25.0 kg 61.2 pounds / 27.8 kg 55.1 pounds / 25.0 kg 32LG500H (32LG500H-UA) 37LG500H (37LG500H-UA) 42LG500H (42LG500H-UA) 36.1 x 26.9 x 11.5 inches 40.4 x 28.8 x 11.5 inches 918.6 x 684.8 x 293.4 mm 1026.2 x 734.0 x 293.4 mm Dimensions (Width x Height x Depth) With stand 31.3 x 23.5 x 8.9 inches 797 x 597 x 227.3 mm Without stand 31.3 x 21.9 x 3.9 inches 797 x 558.6 x 100.5 mm 36.1 x 24.9 x 3.4 inches 918.6 x 632.8 x 88 mm 40.4 x 27.0 x 4.4 inches 1026.2 x 687.9 x 111.8 mm Weight With stand Without stand 21.6 pounds / 9.82 kg 18.3 pounds / 8.34 kg 41.6 pounds / 18.8 kg 35.2 pounds / 15.9 kg 49.1 pounds / 22.3 kg 43.2 pounds / 19.6 kg PRODUCT SPECIFICATIONS 32LC5DC/S/B (32LC5DC/S/B-UA) 32LC50C/S/B (32LC50C/S/B-UA) 37LC5DC/1/B (37LC5DC/1/B-UA) 37LC50C/B (37LC50C/B-UA) 42LC5DC (42LC5DC-UA) 42LC50C (42LC50C-UA) 32LX5DC/S (32LX5DC/S-UA) 32LX50C/S (32LX50C/S-UA) Width x Height x Depth (inches/mm) With Stand 31.8 x 23.9 x 9.8 inches 806.6 x 607.5 x 249.0 mm 31.8 x 21.7 x 3.8 inches 806.6 x 552.3 x 97.2 mm Without Stand 33.7 pounds / 15.3kg 27.6 pounds / 12.5 kg Weight (pounds / kg) With Stand Without Stand Width x Height x Depth (inches/mm) With Stand 36.5 x 27.4 x 10.4 inches 926.8 x 695.8 x 264.6 mm Without Stand 36.5 x24.8 x 4.2 inches 926.8 x 629.8 x 107.4 mm Weight (pounds / kg) With Stand Without Stand 47.2 pounds / 21.4 kg 36.8 pounds / 16.7 kg Width x Height x Depth (inches/mm) With Stand 40.7 x 29.6 x 11.6 inches 1033.1 x 750.7 x 294.2 mm Without Stand 40.7 x 27.0x 4.3 inches 1033.1 x 686.5 x 110.2 mm Weight (pounds / kg) With Stand Without Stand 61.3 pounds / 27.8 kg 47.2 pounds / 21.4 kg Width x Height x Depth (inches/mm) With Stand 36.3 x 24.2 x 11.3 inches 922.0 x 615.0x 288.0 mm Without Stand 36.3 x 21.5 x 3.9 inches 922.0 x 546.0 x 98.0 mm Weight (pounds / kg) With Stand 39.0 pounds / 17.7 kg 30.4 pounds / 13.8 kg Without Stand Width x Height x Depth (inches/mm) 42PX8DC (42PX8DC-UA) Weight (pounds / kg) With Stand 46.7 x 28.1 x 10.6 inches 1186.0 x 714.0 x 270.0 mm Without Stand 46.7 x 25.7 x 3.9 inches 1186.0 x 654.0 x 99.0 mm With Stand 72.5 pounds / 32.9 kg 55.6 pounds / 25.2 kg Without Stand Width x Height x Depth (inches/mm) With Stand Without Stand Weight (pounds / kg) 40.7 x 29.6 x 11.6 inches 1033.1 x 750.7 x 294.2 mm 40.7 x 27.0x 4.3 inches 1033.1 x 686.5 x 110.2 mm 61.3 pounds / 27.8 kg 47.2 pounds / 21.4 kg With Stand Without Stand Power requirement AC100-240V ~ 50/60Hz Television System NTSC-M, ATSC, 64 & 256 QAM Program Coverage VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135 External Antenna Impedance Operating Temperature Range ■ 75 ohm 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% Storage Temperature Range -4 ~ 140°F (-20 ~ 60°C) Storage Humidity Range APPENDIX 42LB5DC (42LB5DC-UA) 42LB50C (42LB50C-UA) Less than 85% The specifications shown above may be changed without prior notice for quality improvement. 83 APPENDIX PROGRAMMING THE REMOTE CONTROL The provided universal remote control can be programmed to operate most remote-controllable devices. Note that the remote may not control all models of other brands. Programming a code into a remote mode To find out whether your remote control can operate each device without programming, turn on the device (such as a VCR) and press the corresponding mode button on the remote. After that, press the POWER button. If the device is turned off and it responds properly the remote control need not be programmed. If not, the remote should be programmed to operate the device. The programming procedures are explained below. Press the M E N U and M U T E button continuously at the same time for two seconds; the currently selected device button is illuminated. If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case, you have to repeat from step 2. Enter the appropriate code from the code table on the following pages. When pressing the button, the light blinks at a time. If the device turned off, the programming is successful. Press the M E N U button to store the code. After blinking twice, this code is stored. Test the remote control functions to see if the device responds properly. If not, steps 2-5. APPENDIX Remote Control Code DVD Brand Codes APEX DIGITAL 022 DENON 020 GE 005 HARMAN KARDON JVC 012 LG 001 MAGNAVOX 013 MARANTZ 024 84 014 006 027 010 016 025 Brand Codes Brand Codes MITSUBISHI NAD ONKYO PANASONIC PHILIPS PIONEER PROCEED PROSCAN 002 023 008 003 013 004 021 005 RCA SAMSUNG SONY THOMPSON TOSHIBA YAMAHA ZENITH 005 011 007 005 019 009 010 017 009 026 006 006 015 006 008 018 016 025 VCR Brand AIWA AKAI Codes Codes Brand MAGNAVOX 031 033 034 041 067 068 012 031 033 067 SAMSUNG 043 046 124 146 MARANTZ 069 033 023 037 031 103 039 043 129 033 MARTA MATSUI MEI MEMOREX 040 033 007 108 116 135 041 010 064 110 111 117 119 MGA MINOLTA MITSUBISHI 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 023 039 043 053 017 031 037 131 008 025 034 046 138 009 033 109 136 012 018 063 033 033 013 066 063 072 144 147 031 050 150 034 048 012 106 027 035 101 153 010 045 026 034 137 150 015 033 101 033 043 055 060 152 039 043 MTC MULTITECH NEC NORDMENDE OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RCA REALISTIC 013 020 114 123 009 013 014 034 101 106 RICO RUNCO SALORA 013 063 031 031 067 101 013 108 072 011 033 013 040 107 145 003 031 053 058 148 014 030 033 010 034 102 046 020 020 051 014 031 053 072 134 139 059 045 046 059 061 040 034 023 039 043 054 070 074 083 140 145 020 031 033 034 067 033 034 054 071 101 021 048 014 066 020 041 109 147 008 033 054 075 033 062 140 145 034 063 144 010 014 034 040 101 Codes 032 105 113 125 SANSUI 022 SANYO 003 102 SCOTT 017 131 SEARS 003 013 031 101 SHARP 031 SHINTOM 024 SONY 003 056 077 SOUNDESIGN 034 STS 013 SYLVANIA 031 067 SYMPHONIC 034 TANDY 010 TATUNG 039 TEAC 034 TECHNICS 031 TEKNIKA 019 101 THOMAS 034 TMK 006 TOSHIBA 008 059 TOTEVISION 040 UNITECH 040 VECTOR RESEARCH 012 VICTOR 048 VIDEO CONCEPTS 012 VIDEOSONIC 040 WARDS 003 031 053 YAMAHA 012 ZENITH 034 058 040 102 104 107 109 112 115 120 122 043 048 135 007 010 014 134 037 112 129 008 009 010 014 017 020 042 073 081 054 149 009 031 052 057 058 076 078 149 033 034 059 034 043 039 043 033 070 031 033 034 013 042 047 082 112 131 101 APPENDIX 034 016 125 AMPRO 072 ANAM 031 AUDIO DYNAMICS 012 BROKSONIC 035 CANON 028 CAPEHART 108 CRAIG 003 CURTIS MATHES 031 DAEWOO 005 065 112 DAYTRON 108 DBX 012 DYNATECH 034 ELECTROHOME 059 EMERSON 006 029 036 129 FISHER 003 FUNAI 034 GE 031 107 GO VIDEO 132 HARMAN KARDON HITACHI 004 043 INSTANTREPLAY 031 JCL 031 JCPENNY 012 040 JENSEN 043 JVC 012 048 130 KENWOOD 014 047 LG (GOLDSTAR) 001 101 LLOYD 034 LXI 003 017 MAGIN 040 Brand 034 046 013 033 054 034 048 072 017 034 131 039 056 080 024 040 043 101 85 APPENDIX SET ID Use this function to specify a TV ID number. SETUP VIDEO Press the M E N U button and then use D or E or or button to select the OPTION menu. AUDIO TIME Aspect Ratio Caption/Text Caption Options Language OPTION SCREEN ISM Method Low Power LOCK Press the G or button and then use or button to select Set ID. Set ID or E or Press the G or button and then use D or E or or button to adjust Set ID to choose the desired TV ID number. The adjustment range of Set ID is 1~99. SETUP VIDEO AUDIO TIME OPTION APPENDIX 86 Press E X I T or R E T U R N button to return to TV viewing or press M E N U button to return to the previous menu. SCREEN LOCK Aspect Ratio Caption/Text Caption Options Language ISM Method Low Power Set ID IR CODES (Hexa) Code Function Note Code 0F TV INPUT Remote control Button (Some models) D6 0B INPUT Remote control Button 08 POWER Remote control Button (Power On/Off) 98 MULTI Remote control Button (Some models) 79 RATIO Remote control Button 0E TIMER Remote control Button 10-19 Number Key 0-9 Remote control Button 4C - (Dash) Remote control Button 1A FLASH BACK Remote control Button 09 MUTE Remote control Button 02 VOL + Remote control Button 03 VOL - Remote control Button 00 CH + , Remote control Button 01 CH - , Remote control Button 39 CC Remote control Button 40 D , Remote control Button 41 Remote control Button 07 F , Remote control Button 06 G , Remote control Button (Hexa) C4 POWER ON C5 POWER OFF 5A D0 COMPONENT D5 RGB-PC CE CC 77 Ratio 16:9 EXIT, RETURN Remote control Button 0A SAP Remote control Button PIP CH + Remote control Button 61 PIP INPUT Remote control Button 63 SWAP, PIP SWAP Remote control Button Discrete IR Code Discrete IR Code Discrete IR Code (Only 16:9 Mode) Ratio Zoom Discrete IR Code (Only Zoom1 Mode) APPENDIX 71 Discrete IR Code (Only 4:3 Mode) 5B Remote control Button HDMI2 Ratio 4:3 Remote control Button (Some models) AF PIP CH - HDMI1/DVI 76 EZ PIC 72 Discrete IR Code (HDMI2 Input Selection) 4D Remote control Button Discrete IR Code (HDMI1/DVI Input Selection) Remote control Button (Some models) Remote control Button Discrete IR Code (RGB-PC Input Selection) EZ SOUND INFO Discrete IR Code (Component Input Selection) 52 PIP AV2 BF Remote control Button 60 AV1 (AV2 Input Selection) Remote control Button AA Discrete IR Code (AV1 Input Selection) ENTER Remote control Button (Some models) Discrete IR Code (Only Power Off) MENU E0 Discrete IR Code (Only Power On) 43 Remote control Button (Some models) TV Note (TV Input Selection) 44 E1 Function 87 Regulatory Information cont. FCC Compliance Statement respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This equipment has been tested and found to comply within the limits of a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. CE Conformity Notice (for Europe) This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Products with the “CE” Marking comply with the EMC Directive(89/336/EEC) and LOW VOLTAGE Directive (73/23/EEC) issued by the Commission of the European Community. Compiance with these directives implies conformity to the following European Norms : • EN 55022 ; Radio Frequency Interference • EN 55024 ; Electromagnetic Immunity • EN 61000-3-2 ; Power Line Harmonics • EN 61000-3-3 ; Voltage Fluctuations • EN 60950-1 ; Product Safety If this equipment does cause harmful interference to radio or television reception (which can be determined by turning the equipment on and off), the user is encouraged to try to correct the interference by using one or more of the following measures: NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Low Radiation Compliance (MPR II) This monitor meets one of the strictest guidelines available today for low radiation emissions, offering the user extra shielding and an antistatic screen coating. These guidelines, set forth by a government agency in Sweden, limit the amount of emission allowed in the Extremely Low Frequency (ELF) and Very Low Frequency (VLF) electromagnetic range. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's (or your) authority to operate the equipment. Only peripherals (digital input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this monitor. Operation with non-certified peripherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used with this System. TCO'99 (TCO'99 applied model only) NOTICE The regulations are applied only to the products with the ID LABEL indicating specific requirements. Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products. Canadian DOC Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B 01 Regulatory Information cont. Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. With the growing manufacture and usage of electronic equipment throughout the world, there is a recognized concern for the materials and substances used by electronic products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. visual ergonomics. Below you will find a brief summary of the ecological requirements met by this product. The complete ecological criteria document can be found at TCO Development’s website http://www.tcodevelopment.com or may be ordered from: TCO Development SE-114 94 STOCKHOLM, Sweden Fax: +46 8 782 92 07 Email : development@tco.se Information regarding TCO’99 approved and labelled products may also be obtained at http://www.tcodevelopment.com There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments. Electronic equipment in offices is often left running continuously, resulting in unnecessary consumption of large amounts of energy and additional power generation. From the standpoint of carbon dioxide emissions alone, it is vital to save energy. Ecological requirements Flame retardants Flame retardants may be present in printed wiring board laminates, cables, and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% by weight of the plastic in a computer casing can consist of flame retardant substances. Many flame retardants contain bromine or chlorine, and these flame retardants are chemically related to PCBs (polychlorinated biphenyls). Both the flame retardants containing bromine or chlorine and the PCBs are suspected of giving rise to health effects, including reproductive damage in fisheating birds and mammals, due to the bio-accumulative* processes when not disposed of in accordance with strict standards for disposal. What does labelling involve? The product meets the requirements for the TCO’99 scheme which provides for international and environmental labelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) and Statens Energimyndighet (The Swedish National Energy Administration). Approval requirements cover a wide range of issues: ecology, ergonomics, emission of electrical and magnetical fields, energy consumption and electrical safety. TCO’99 requires that plastic components weighing more than 25 grams shall not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed wiring board laminates due to the lack of commercially available alternatives. Ecological criteria impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, and other substances. The product must be prepared for recycling and the manufacturing site(s) shall be certified according to ISO14001 or EMAS registered. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. TCO’99 requires that batteries, the colour-generating layers of display screens, and the electrical or electronics components shall not contain any cadmium. Energy requirements include a demand that the system unit and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more stages. The length of time to reactivate the system unit shall be reasonable for the user. Mercury** Mercury is sometimes found in batteries, relays and switches. TCO’99 requires that batteries shall not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one Labelled products must meet strict environmental demands, for example, in respect of the reduction of electrical and magnetical fields as well as work load and 02 Regulatory Information cont. • exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as there today is no commercially available alternative. TCO aims on removing this exception when a mercury free alternative is available. Noise emissions Ecology • The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 001 • Restrictions on chlorinated and brominated flame retardants and polymers heavy metals such as cadmium, mercury and lead. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. TCO’99 permits the use of lead due to the lack of commercially available alternatives, but in future requirements TCO Development aims at restricting the use of lead. _____________________________________________ The requirements included in this label have been developed by TCO Development in co-operation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. * Bio-accumulative is defined as substances which accumulate in living organisms. **Lead, Cadmium and Mercury are heavy metals which are bio-accumulative. TCO’03 (TCO’03 applied model only) For more information, please visit www.tcodevelopment.com English Congratulations! The display you have just purchased carries the TCO’03 Displays label. This means that your display is designed,manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO’03 Display requirements: Information for Environmental Preservation LGE. announced the 'LG Declaration for a Cleaner Environment' in 1994, and this ideal has served as a guiding managerial principle ever since. The Declaration is a foundation that has allowed us to undertake environmentally friendly activities in careful consideration of economic, environmental, and social aspects. We promote activities for environmental preservation, and we specifically develop our products to embrace the concept of environment-friendly. We minimize the hazardous materials contained in our products. For example, there is no cadmium to be found in our monitors. Ergonomics • Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Information for recycling This monitor may contain parts which could be hazardous to the environment. It is important that this monitor be recycled after use. Energy • Energy-saving mode after a certain time – beneficial both for the user and the environment • Electrical safety LGE. handles all waste monitors through an environmentally acceptable recycling method. There are several take-back and recycling systems currently in Emissions • Electromagnetic fields 03 Regulatory Information cont. operation worldwide. Many parts will be reused and recycled, while harmful substances and heavy metals are treated by an environmentally friendly method. If you want to find out more information about our recycling program, please contact your local LG vendor or a corporate representative of LG. Wir richten unsere Firmenpolitik auf eine sauberere Umwelt hin aus, indem wir umweltspezifische Aspekte als wichtigen Punkt in die Weiterentwicklung unseres Unternehmens einfließen lassen. Zusätzliche Informationen über unsere ‘grüne’ Firmenpolitik erhalten Sie auf unserer Website. http://www.lge.com/about/environment/html/Recycling.jsp We set our vision and policies on a cleaner world by selecting the issue of the global environment as a task for corporate improvement. Please visit our website for more information about our ‘green’ policies. http://www.lge.com/about/environment/html/Recycling.jsp Français Information sur la protection del’environnement LGE. a publié sa 'Déclaration en faveur d’un environnement plus propre' en 1994 et celle-ci est restée, depuis lors, un principe directeur de notre entreprise. Cette déclaration a servi de base à notre réflexion et nous a permis de prendre en compte à la fois les aspects économiques et sociaux de nos activités, tout en respectant l’environnement. Deutsch Informationen zur Erhaltung der Umwelt Im Jahr 1994 verkündete LGE die 'LG Declaration for a Cleaner Environment' (LG Erklärung für eine sauberere Umwelt). Seitdem dient dieses Ideal als führendes Prinzip des Unternehmens. Diese Erklärung war die Basis für die Durchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche, umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden. Wir fördern Aktivitäten zum Schutz der Umwelt und die Entwicklung unserer Produkte ist darauf ausgerichtet, unserem Konzept bezüglich Umweltfreundlichkeit gerecht zu werden. Wir sind darauf bedacht, den Anteil der in unseren Produkten enthaltenen schädlichen Materialien zu minimieren. So ist in unseren Monitoren beispielsweise kein Kadmium zu finden. Nous encourageons les activités en faveur de la préservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons au minimum les matières dangereuses qui entrent dans leur composition et l’on ne trouve pas de cadmium, par exemple, dans nos moniteurs. Information sur le recyclage Ce moniteur peut contenir des composants qui présentent un risque pour l’environnement. Il est donc important que celui-ci soit recyclé après usage. LGE. traite les moniteurs en fin de cycle conformément à une méthode de recyclage respectueuse de l’environnement. Nous reprenons nos produits et les recyclons dans plusieurs sites répartis dans le monde entier. De nombreux composants sont réutilisés et recyclés, et les matières dangereuses, ainsi que les métaux lourds, sont traités selon un procédé écologique. Si vous souhaitez plus de renseignements sur notre programme de recyclage, veuillez contacter votre revendeur LG ou un l’un de nos représentants. Informationen zum Thema Recycling Dieser Monitor enthält Teile, die umweltschädlich sein können. Es ist unbedingt erforderlich, dass der Monitor recycelt wird, nachdem er außer Dienst gestellt wurde. Bei LGE. werden alle ausrangierten Monitore in einem unter umweltbezogenen Aspekten geeigneten Verfahren recycelt. Augenblicklich sind weltweit mehrere Rücknahme- und Recyclingsysteme im Einsatz. Viele Teile werden wieder verwendet und recycelt. Schädliche Substanzen und Schwermetalle werden durch umweltverträgliche Verfahren behandelt. Falls Sie mehr über unser Recyclingprogramm erfahren möchten, wenden Sie sich bitte an Ihren lokalen LGHändler oder einen Unternehmensvertreter von LG. Nous voulons agir pour un monde plus propre et croyons au rôle de notre entreprise dans l’amélioration de l’environnement. Pour plus de renseignements sur notre politique “verte”, rendez visite à notre site : http://www.lge.com/about/environment/html/Recycling.jsp 04 Regulatory Information cont. Italiano respetan el medio ambiente siempre teniendo en cuenta aspectos sociales, económicos y medioambientales. Informazioni per la tutela dell’ambiente La LGE. ha annunciato nel 1994 la cosiddetta 'LG Declaration for a Cleaner Environment' (Dichiarazione di LG a favore di un ambiente più pulito), un ideale che da allora funge da principio ispiratore della gestione aziendale. La dichiarazione rappresenta il fondamento che consente di intraprendere attività a favore dell'ambiente tenendo conto degli aspetti economici, ambientali e sociali.Noi della LG, promuoviamo attività a favore della tutela dell'ambiente sviluppando appositamente i nostri prodotti per cogliere il concetto del rispetto dell’ambiente riducendo i materiali dannosi presenti nei nostri prodotti. Ad esempio nei nostri monitor non è presente il cadmio. Promocionamos actividades orientadas a la conservación del medio ambiente y desarrollamos nuestros productos específicamente para que se ajusten a la filosofía que protege el entorno. Reducimos al máximo el uso de materiales de riesgo en nuestros productos. Un ejemplo de ello es la ausencia total de cadmio en nuestros monitores. Información para el reciclaje Este monitor puede contener piezas que entrañen riesgos medioambientales. Es importante reciclar este monitor después de su utilización. LGE. trata todos los monitores usados siguiendo un método de reciclaje que no daña al entorno. Contamos con diversos sistemas de recuperación y reciclaje que funcionan a nivel mundial en la actualidad. Es posible reciclar y reutilizar muchas de las piezas, mientras que las sustancias dañinas y los metales pesados se tratan siguiendo un método que no perjudique al medio ambiente. Si desea obtener más información acerca del programa de reciclaje, póngase en contacto con su proveedor local de LG o con un representante empresarial de nuestra marca. Informazioni per il riciclaggio Il monitor può presentare componenti che potrebbero risultare eventualmente dannosi per l'ambiente. È importante che il monitor sia riciclato al termine del suo utilizzo. La LGE. gestisce tutti i monitor di rifiuto con un metodo di riciclaggio soddisfacente dal punto di vista ambientale. In tutto il mondo sono attualmente in funzione numerosi sistemi di riciclaggio e recupero. I diversi componenti sono riutilizzati e riciclati, mentre le sostanze dannose e i metalli pesanti vengono trattati con un metodo rispettoso dell’ambiente. Se si desiderano maggiori informazioni in merito al programma di riciclaggio, è consigliabile rivolgersi al proprio rivenditore LG o ad un rappresentante aziendale della LG. Basamos nuestra visión y nuestras políticas en un mundo más limpio y para ellos optamos por un entorno global como tarea principal de nuestra evolución como empresa. Visite nuestra página Web para obtener más información sobre nuestras políticas ecológicas. http://www.lge.com/about/environment/html/Recycling.jsp Noi della LG impostiamo la nostra visione e le nostre politiche a favore di un mondo più pulito ponendo la questione dell'ambiente dal punto di vista globale come una mansione rivolta al miglioramento della nostra azienda. Vi invitiamo a visitare il nostro sito internet per ulteriori informazioni sulla nostra politica “verde”. http://www.lge.com/about/environment/html/Recycling.jsp Português Informações relacionadas à preservação ambiental A LGE. anunciou a 'LG Declaration for a Cleaner Environment' (Declaração da LG para um ambiente mais limpo) em 1994 e esse ideal tem servido desde então como um princípio administrativo de orientação. A Declaração é a base que nos tem permitido realizar atividades favoráveis ao ambiente com consideração atenta aos aspectos econômicos, ambientais e sociais. Espanõl Información para la conservación medioambiental LGE. presentó la 'Declaración para un entorno más limpio de LG' en 1994 y este ideal ha servido para guiar nuestros principios empresariales desde entonces. La Declaración es la base que nos ha permitido llevar a cabo tareas que Promovemos atividades de preservação ambiental e desenvolvemos nossos produtos para englobar 05 Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossos produtos. Por exemplo, não há cádmio em nossos monitores. Informatie met betrekking tot recycling Deze monitor bevat materialen die schadelijk zouden kunnen zijn voor het milieu. Het is belangrijk dat deze monitor aan het einde van zijn levensduur wordt gerecycled. Informações relacionadas à reciclagem Este monitor pode conter peças que podem representar riscos ao ambiente. É importante que ele seja reciclado após o uso. LGE. verwerkt alle afvalmonitors via een milieuvriendelijke recyclingmethode. Hiervoor worden er momenteel wereldwijd verscheidene inname- en recyclingsystemen gehanteerd. Een groot aantal onderdelen wordt opnieuw gebruikt en gerecycled, waarbij schadelijke stoffen en zware metalen volgens een milieuvriendelijke methode worden verwerkt. Voor meer informatie over ons recyclingprogramma kunt u contact opnemen met uw plaatselijke LGvertegenwoordiger of een LG-vestiging. A LGE. cuida de todos os monitores descartados através de um método de reciclagem agradável ao ambiente. Há vários sistemas de devolução e reciclagem atualmente em operação no mundo. Muitas peças serão reutilizadas e recicladas e as substâncias nocivas e os metais pesados passarão por tratamento através de um método favorável ao ambiente. Para obter mais informações sobre nosso programa de reciclagem, entre em contato com seu fornecedor LG local ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas a um mundo mais limpo selecionando a questão do ambiente global como uma tarefa de aprimoramento corporativo. Visite nosso site para obter mais informações sobre nossas políticas de meio ambiente. http://www.lge.com/about/environment/html/Recycling.jsp Onze visie en ons beleid met betrekking tot een schonere wereld vloeien voort uit het feit dat wij het milieu hebben aangemerkt als een onderwerp dat speciale aandacht verdient binnen onze onderneming. Bezoek onze website voor meer informatie over ons 'groene' beleid. http://www.lge.com/about/environment/html/Recycling.jsp Russian »ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ Nederlands ¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡ 'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚', ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏ ÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎË Ô‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘Ë ·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓÏ ‰ÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ Ë ÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï. Informatie met betrekking tot het behoud van het milieu LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner Environment' (de LG-verklaring met betrekking tot een schoner milieu). Deze verklaring en het ideaal van een schoner milieu fungeren sindsdien als een bestuurlijke leidraad voor onze onderneming. Op basis van deze verklaring ontplooien wij milieuvriendelijke activiteiten, waarbij er zowel met sociale en economische aspecten, als met milieuaspecten zorgvuldig rekening wordt gehouden. Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌË ‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò ÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË. Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı ‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯Ëı ÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ. Wij ondersteunen activiteiten die zijn gericht op het behoud van het milieu en wij houden bij het ontwikkelen onze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen in onze producten. Er wordt bijvoorbeeld geen cadmium verwerkt in onze monitors. »ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ ›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚, ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â. 06 Regulatory Information cont. ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒΠËÒÔÓθÁÓ‚‡Ìˡ. KÓÔÓ‡ˆËˇ LGE Ô‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ ÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚ ·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚ ·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡. «‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈ ÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ Í ÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ ÍÓÔÓ‡ˆËË LG. Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛ ÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛ Ó Ì‡¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚ ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ: http://www.lge.com/about/environment/html/Recycling.jsp EPA (EPA applied model only) ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA). As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. NOM MARK (Mexico only) 07 Regulatory Information cont. WEEE un bidone della spazzatura barrato da una croce significa che il prodotto è coperto dalla direttiva europea 2002/96/EC. 2.Tutti i prodotti elettrici ed elettronici dovrebbero essere smaltiti separatamente rispetto alla raccolta differenziata municipale, mediante impianti di raccolta specifici designati dal governo o dalle autorità locali. 3.Il corretto smaltimento delle apparecchiature obsolete contribuisce a prevenire possibili conseguenze negative sulla salute umana e sull'ambiente. 4.Per informazioni più dettagliate sullo smaltimento delle apparecchiature obsolete, contattare il comune, il servizio di smaltimento rifiuti o il negozio in cui è stato acquistato il prodotto. (for Europe ) English Disposal of your old appliance 1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC. 2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. 3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health. 4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product. Swedish Kassering av din gamla apparat 1.När den här symbolen med en överkryssad soptunna på hjul sitter på en produkt innebär det att den regleras av European Directive 2002/96/EC. 2.Alla elektriska och elektroniska produkter bör kasseras via andra vägar än de som finns för hushållsavfall, helst via för ändamålet avsedda uppsamlingsanläggningar som myndigheterna utser. 3.Om du kasserar din gamla apparat på rätt sätt så bidrar du till att förhindra negativa konsekvenser för miljön och människors hälsa. 4.Mer detaljerad information om kassering av din gamla apparat kan får av kommunen, renhållningsverket eller den butik där du köpte produkten. French Élimination de votre ancien appareil 1.Ce symbole, représentant une poubelle sur roulettes barrée d'une croix, signifie que le produit est couvert par la directive européenne 2002/96/EC. 2.Les éléments électriques et électroniques doivent être jetés séparément, dans les videordures prévus à cet effet par votre municipalité. 3.Une élimination conforme aux instructions aidera à réduire les conséquences négatives et risques éventuels pour l'environnement et la santé humaine. 4.Pour plus d'information concernant l'élimination de votre ancien appareil, veuillez contacter votre mairie, le service des ordures ménagères ou encore la magasin où vous avez acheté ce produit. Dutch Uw oude toestel wegdoen 1.Als het symbool met de doorgekruiste verrijdbare afvalbak op een product staat, betekent dit dat het product valt onder de Europese Richtlijn 2002/96/EC. 2.Elektrische en elektronische producten mogen niet worden meegegeven met het huishoudelijk afval, maar moeten worden ingeleverd bij speciale inzamelingspunten die door de lokale of landelijke overheid zijn aangewezen. 3.De correcte verwijdering van uw oude toestel helpt negatieve gevolgen voor het milieu en de menselijke gezondheid voorkomen. Italian Smaltimento delle apparecchiature obsolete 1.Quando su un prodotto è riportato il simbolo di 08 Regulatory Information cont. 4.Wilt u meer informatie over de verwijdering van uw oude toestel? Neem dan contact op met uw gemeente, de afvalophaaldienst of de winkel waar u het product hebt gekocht. eller de lokale myndigheder. 3.Korrekt bortskaffelse af dit gamle apparat er med til at forhindre mulige skadevirkninger på miljøet og menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse af dit gamle apparat kan fås ved at kontakte dit lokale kommunekontor, renovationsselskab eller den butik, hvor du købte produktet. Finnish Vanhojen laitteiden hävittäminen 1.Tämä merkki tuotteessa tarkoittaa, että tuote kuuluu sähkö- ja elektroniikkalaiteromusta annetun EU-direktiivin 2002/96/EY soveltamisalaan. 2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseen keräyspisteeseen. 3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia. 4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin, kierrätyskeskukseen tai myymälään, josta ostit laitteen. Greek ∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ 1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜ ‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓ Î·Ï‡ÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK. 2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓ ÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿ ·fi Ù· ÁÂÓÈο ÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈÛÌ¤ÓˆÓ ÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜ ¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘ ÙÔÈΤ˜ ·Ú¯¤˜. 3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı· ‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓ ˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘. 4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ Ì ÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ ·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·Ù ÙÔ ÚÔ˚fiÓ. German Entsorgung von Altgeräten 1.Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europäischen Richtlinie 2002/96/EC. 2.Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt werden. 3.Mit der ordnungsgemäßen Entsorgung des alten Geräts vermeiden Sie Umweltschäden und eine Gefährdung der persönlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des alten Geräts erhalten Sie bei der Stadtverwaltung, beim Entsorgungsamt oder in dem Geschäft, wo Sie das Produkt erworben haben. Spanish Cómo deshacerse de aparatos eléctricos y electrónicos viejos 1.Si en un producto aparece el símbolo de un contenedor de basura tachado, significa que éste se acoge a la Directiva 2002/96/CE. 2.Todos los aparatos eléctricos o electrónicos se deben desechar de forma distinta del servicio municipal de recogida de basura, a través de puntos de recogida designados por el gobierno o las autoridades locales. 3.La correcta recogida y tratamiento de los dispositivos inservibles contribuye a evitar riesgos potenciales para el medio ambiente y la salud pública. 4.Para obtener más información sobre cómo deshacerse de sus aparatos eléctricos y electrónicos viejos, póngase en contacto con su ayuntamiento, el servicio de recogida de basuras o el establecimiento donde adquirió el producto. Danish Sådan smider du dit gamle apparat ud 1.Når der er et tegn med et kryds over en skraldespand, betyder det, at produktet er omfattet af EU-direktiv 2002/96/EC. 2.Alle elektriske og elektroniske produkter skal smides ud et andet sted end gennem den kommunale affaldsordning ved hjælp af specielle indsamlingsfaciliteter, der er organiseret af staten 09 Regulatory Information cont. Portuguese Hungarian Slovak Polish Czech Croatian 10 Regulatory Information cont. Estonian Latvian Lithuanian 11
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No XMP Toolkit : 3.1-702 Producer : Acrobat Distiller 7.0.5 (Windows) Create Date : 2009:01:13 16:33:04+09:00 Creator Tool : PScript5.dll Version 5.2.2 Modify Date : 2009:01:13 17:43:09+09:00 Metadata Date : 2009:01:13 17:43:09+09:00 Format : application/pdf Title : Microsoft Word - User_s Manual_H_ok.doc Creator : EMC CENTER Document ID : uuid:567fcace-d374-4f64-958d-55a1fefd1b9b Instance ID : uuid:1efcc7f2-163e-4448-9999-563941ef4dc0 Has XFA : No Page Count : 53 Author : EMC CENTEREXIF Metadata provided by EXIF.tools