LG Electronics USA 37LG710HUA LCD TV MONITOR User Manual User s Manual G

LG Electronics USA LCD TV MONITOR User s Manual G

UserManual.wiki >

LG Electronics USA >

37LG710HUA User Manual HTML Version

USERS MANUAL

Order Number : GETEC-C1-09-168 FCC Class B Certification

Test Report Number : GETEC-E3-09-087 Page 1 / 1

EUT Type: LCD TV/ Monitor

FCC ID.: BEJ37LG710HUA

APPENDIX G

: USER’S MANUAL

Please read this manual carefully before operating

your set.

Retain it for future reference.

Record model number and serial number of the set.

See the label attached on the back cover and quote

this information to your dealer

when you require service.

LCD TV

OWNER’S MANUAL

32LG700H 32LG710H

37LG700H 37LG710H

42LG700H 42LG710H

Installer Reference for Commercial Mode

MPI/PPV Card Setup see page 19

Commercial Mode Setup see pages 85-107

P/NO : SAC30708043 (0907-REV05)

www.lgcommercial.com

This product qualifies for ENERGY STAR in the “factory

default” setting and this is the setting in which power savings

will be achieved.

Changing the factory default picture setting or enabling other

features will increase power consumption that could exceed

the limits necessary to quality for Energy Star rating.

1-800-243-0000 USA, Consumer User

1-888-865-3026 USA, Commercial User

1-888-542-2623 CANADA

LG Customer Information Center

Model:

Serial:

WARNING / CAUTION

To prevent fire or shock hazards, do not expose

this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy

and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to

radio or television reception, which can be determined

by turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment to an outlet on a circuit

different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV

technician for help.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two condi-

tions: (1) This device may not cause (harmful)

interference, and (2) this device must accept any

interference received, including interference that

may cause undesired operation (of the device).

Any changes or modifications in construction of this

device which are not expressly approved by the party

responsible for compliance could void the user’s

authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any way

without written authorization from LG Electronics.

Unauthorized modification could void the user’s

authority to operate this product

The lightning flash with arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence

of uninsulated “dangerous voltage” within the

product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating

and maintenance (servicing) instructions in the

literature accompanying the appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC

SHOCK, DO NOT EXPOSE THIS PRODUCT TO

RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the National

Electric Code (U.S.A.). The code provides guidelines for

proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system

of the building, as close to the point of the cable entry

as practical.

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including amplifiers)that produce heat.

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has

two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong, The wide blade or the third

prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on

or pinched particularly at plugs, convenience

receptacles, and the point where they exit from

the apparatus.

Only use attachments/accessories specified by

the manufacturer.

Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lighting storms or

when unused for long periods of time.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Never touch this apparatus or antenna during a

thunder or lighting storm.

When mounting a TV on the wall, make sure not to

install the TV by the hanging power and signal

cables on the back of the TV.

Do not allow an impact shock or any objects to fall

into the product, and do not drop onto the screen

with something.

CAUTION concerning the Power Cord :

It is recommend that appliances be placed upon a

dedicated circuit; that is, a single outlet circuit which

powers only that appliance and has no additional

outlets or branch circuits. Check the specification

page of this owner's manual to be certain.

Do not connect too many appliances to the same

AC power outlet as this could result in fire or elec-

tric shock.

Do not overload wall outlets. Overloaded wall out-

lets, loose or damaged wall outlets, extension cords,

frayed power cords, or damaged or cracked wire

insulation are dangerous. Any of these conditions

could result in electric shock or fire. Periodically

examine the cord of your appliance, and if its

appearance indicates damage or deterioration,

unplug it, discontinue use of the appliance, and

have the cord replaced with an exact replacement

part by an authorized servicer. Protect the power

cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or

walked upon. Pay particular attention to plugs, wall

outlets, and the point where the cord exits the

appliance.

Do not make the TV with the power cord plugged

in. Do not use a damaged or loose power cord. Be

sure do grasp the plug when unplugging the power

cord. Do not pull on the power cord to unplug the

TV.

WARNING - To reduce the risk of fire or electrical

shock, do not expose this product to rain, moisture

or other liquids. Do not touch the TV with wet

hands. Do not install this product near flammable

objects such as gasoline or candles or expose the

TV to direct air conditioning.

Do not expose to dripping or splashing and do not

place objects filled with liquids, such as vases, cups,

etc. on or over the apparatus (e.g. on shelves above

the unit).

GGRROOUUNNDDIINNGG

Ensure that you connect the earth ground wire to

prevent possible electric shock. (i.e. a TV with a

three-prong grounded AC plug must be connected

to a three-prong grouned AC outlet) If grounding

methods are not possible, have a qualified electri-

cian install a separate circuit breaker.

Do not try to ground the unit by connecting it to

telephone wires, lightening rods, or gas pipes.

DDIISSCCOONNNNEECCTTIINNGG DDEEVVIICCEE FFRROOMM MMAAIINNSS

Mains plug is the disconnecting device. The plug

must remain readily operable.

Power

Supply

Short-circuit

Breaker

AANNTTEENNNNAASS

OOuuttddoooorr aanntteennnnaa ggrroouunnddiinngg

If an outdoor antenna is installed, follow the precau-

tions below. An outdoor antenna system should not

be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can

come in contact with such power lines or circuits as

death or serious injury can occur.

Be sure the antenna system is grounded so as to pro-

vide some protection against voltage surges and

built-up static charges.

Section 810 of the National Electrical Code (NEC) in

the U.S.A. provides information with respect to prop-

er grounding of the mast and supporting structure,

grounding of the lead-in wire to an antenna dis-

charge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding

electrodes and requirements for the grounding elec-

trode.

AAnntteennnnaa ggrroouunnddiinngg aaccccoorrddiinngg ttoo tthhee

NNaattiioonnaall EElleeccttrriiccaall CCooddee,, AANNSSII//NNFFPPAA 7700

Cleaning

When cleaning, unplug the power cord and scrub

gently with a soft cloth to prevent scratching. Do not

spray water or other liquids directly on the TV as

electric shock may occur. Do not clean with chemi-

cals such as alcohol, thinners or benzene.

Moving

Make sure the product is turned off, unplugged

and all cables have been removed. It may take 2 or

more people to carry larger TVs. Do not press

against or put stress on the front panel of the TV.

Ventilation

Install your TV where there is proper ventilation. Do

not install in a confined space such as a bookcase.

Do not cover the product with cloth or other mate-

rials (e.g.) plastic while plugged in. Do not install in

excessively dusty places.

If you smell smoke or other odors coming from the

TV or hear strange sounds, unplug the power cord

contact an authorized service center.

Do not press strongly upon the panel with a hand or

sharp object such as nail, pencil or pen, or make a

scratch on it.

Keep the product away from direct sunlight.

FFoorr LLCCDD TTVV

If the TV feels cold to the touch, there may be

a small “flicker” when it is turned on. This is

normal, there is nothing wrong with TV.

Some minute dot defects may be visible on the

screen, appearing as tiny red, green, or blue

spots. However, they have no adverse effect on

the monitor's performance.

Avoid touching the LCD screen or holding your

finger(s) against it for long periods of time.

Doing so may produce some temporary dis-

tortion effects on the screen.

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

ON DISPOSAL

(Only Hg lamp used LCD TV)

The fluorescent lamp used in this product contains

a small amount of mercury. Do not dispose of

this product with general household waste.

Disposal of this product must be carried out in

accordance to the regulations of your local authority.

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 2

FEATURES OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PREPARATION

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Attaching the TV to a desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Securing the TV to the wall to prevent falling

When the TV is used on a stand

. . . . . . . . . . . . . . . . . . . . . . . . . . 17

Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 18

MPI Card Slot / PPV Card Installation . . . . . . . . . . . . . . . 19

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup

- Component Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

- HDMI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

- DVI to HDMI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 22

DVD Setup

- Component Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

- HDMI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

VCR Setup

- Antenna Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

- Composite (RCA) Connection . . . . . . . . . . . . . . . . . . . 25

Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

PC Setup

- VGA (D-Sub 15 pin) Connection . . . . . . . . . . . . . . . 27

- DVI to HDMI Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 28

- Screen Setup for PC mode . . . . . . . . . . . . . . . . . . . . . . . . 29

Audio Out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

WATCHING TV / CHANNEL CONTROL

Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Channel Setup

- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

- Add / Delete Channel (Manual Tuning) . . . . . . 39

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Channel Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Example Electronic Program Guide . . . . . . . . . . . . . . . . . . . 43

PICTURE CONTROL

PIP (Picture-In-Picture) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 46

Preset Picture Settings

- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Manual Picture Adjustment

- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 51

Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 52

Advanced Control - Black (Darkness) Level . . . . . . . 53

Advanced Control - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Advanced Control - Film Mode . . . . . . . . . . . . . . . . . . . . . . . . .55

Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 57

Preset Sound Settings (Sound Mode) . . . . . . . . . . . . . . 58

Sound Setting Adjustment - User Mode . . . . . . . . . . . 59

- SRS TruSurround XT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Clear Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Stereo/SAP Broadcast Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

On-Screen Menus Language Selection . . . . . . . . . . . . . . 67

Caption Mode

- Analog Broadcasting System Captions . . . . . . . 68

- Digital Broadcasting System Captions . . . . . . . . 69

- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

TIME SETTING

Clock Setting

- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

PARENTAL CONTROL / RATINGS

Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

COMMERCIAL MODE SETUP

Interactive TV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Installer Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Interactive TV Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Commercial Mode Setup for Master TV . . . . . . . . . . . . 88

Master TV Profile Setup Learning/Teaching with

USB Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

TLL-1100A Cloning Connections/Learning Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

LT2002 Cloning Connections/Learning Setup . . 92

LT2002 Cloning Learning Setup . . . . . . . . . . . . . . . . . . . . . . 93

Cloning Connections/Teaching Setup . . . . . . . . . . . . . . 94

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

Reference: Detailed Instructions For Making A

Master TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

Reference: Procedures for adding Channel Label

Icons/Custom Channel Labels (2-5-4 + MENU

Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Reference: Clonable Menu Features . . . . . . . . . . . . . . . . 103

Reference: Power Saving Setup . . . . . . . . . . . . . . . . . . . . . . . 10 4

TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

TV Camport Auto Sense Operation . . . . . . . . . . . . . . . . 107

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 8

Reference: LT2002 Cloning Procedure

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Commercial Mode Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

Reference: RJP model list and input hierarchy . . . 112

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114

Programming the Remote Control . . . . . . . . . . . . . . . . . . . 115

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

FEATURES OF THIS TV

is a trademark of SRS Labs, Inc.

TruSurround XT technology is incorporated under

license from SRS Labs, Inc.

Manufactured under license from Dolby Laboratories.

“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

USB IN

SERVUCE ONLYSERVUCE ONLY

USB port shall be used for software update by service

personnel only.

HDMITM, the HDMI logo and High-Definition

Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing."

■

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV

for an extended period, it can become permanently imprinted on the screen. This phenomenon is known

as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty.

■

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period

(2 or more hours for LCD, 1 or more hours for Plasma).

■

Image burn can also occur on the letterboxed

areas of your TV if you use the 4:3 aspect

ratio setting for an extended period.

IMPORTANT INFORMATION TO PREVENT “IMAGE BURN

/ BURN-IN” ON YOUR TV SCREEN

PREPERATION

ACCESSORIES

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the

dealer where you purchased the TV.

The accessories included may differ from the images below.

Owner’s Manual Power Cord

CD Manual Protective Bracket and

Bolt for Power Cord

(Refer to P.13)

Cable Holder

(Refer to P.13)

* Wipe spots on the exterior only with the pol-

ishing cloth.

* Do not wipe roughly when removing stains.

Excessive pressure may cause scratches or

discoloration.

Polishing Cloth

(Not included with all

models.)

FFoorr 3322LLGG770000HH,,

3322LLGG771100HH

OOppttiioonn EExxttrraass

D-sub 15 pin Cable

When using the VGA (D-sub 15 pin

cable) PC connection, the user

must use shielded signal interface

cables with ferrite cores to maintain

standards compliance.

x 2

Torx plus

Star head screw

(Refer to P.12)

Screw for stand fixing

(Refer to P.15) Bolts for stand assembly

(Refer to P.12)

x 4 x 4

1.5V 1.5V

Remote Control,

Batteries

MUTE

RETURN

POWER

GUIDE

PORTAL

ENTER

VOL CH

123

456

FLASHBK

VCR

DVD

INPUT

INFO

STB

PIP SAP

PIP CH- PIP CH+

PIP SWAP

PIP INPUT

ALPHA/NUM

REMOVE

RATIO

TIMER

ABC DEF

GHI

WXYZ

TUV

PQRS

MNO

JKL

.:/,

Protection Cover

(Refer to P.12)

Plug in type Holder

(Refer to P.13)

PREPARATION

FRONT PANEL INFORMATION

■

Image shown may differ from your TV.

POWER Button

Power/Standby Indicator

Illuminates red in standby mode.

Illuminates blue when the set is switched on.

VOL

INPUT

ENTER

VOLUME (+, -)

Buttons

ENTER Button

MENU Button

INPUT Button

Remote Control Sensor

CHANNEL( , )

Buttons

Stand

Intelligent Sensor

Adjusts picture according to

the surrounding conditions.

PREPARATION

■

Image shown may differ from your TV.

BACK PANEL INFORMATION

AV IN 2

L/MONO

AUDIO

VIDEO

USB

SERVICE ONLY

REMOTE

CONTROL

OUT

OPTICAL

DIGITAL

AUDIO OUT

AV IN 1

AUDIO

VIDEO

MONO

UPDATE

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

HDMI/DVI IN

1(DVI)

RJP

INTERFACE

SPEAKER

OUT

RGB

(PC)

AUDIO

(RGB/DVI)

RGB IN

RS-232C IN

(SERVICE ONLY)

( )

ANTENNA

IN M.P

M.P

.I.

10 11

PREPARATION

REMOTE CONTROL OUT

IR output for controlling an auxiliary device.

RJP INTERFACE (REMOTE JACK PACK PORT)

Connect to remote jack pack control output port.

COMPONENT IN

Analog Connection.

Supports HD.

Uses a red, green, and blue cable for video & a red

and white cable for audio.

AV (Audio/Video) IN 1

Analog composite connection. Supports standard

definition video only (480i).

Used for PC/DTV audio input jack.

USB SERVICE ONLY

Used for software updates.

ANTENNA IN

Connect over-the air signals to this jack.

M.P. I.

Control port.

Power Cord Socket

For operation with AC power.

Caution: Never attempt to operate the TV on DC

power.

HDMI/DVI IN

Digital Connection. Supports HD video and Digital

audio.

Accepts DVI video using an adapter or HDMI to

DVI cable (not included)

LAN (SERVICE ONLY)

For connecting to a control network.

RESET

Performs a hardware reset.

UPDATE

Enables/disables software downloads and debug

mode.

OPTICAL DIGITAL AUDIO OUT

Optical digital audio output for use with amps and

home theater systems.

Note: In standby mode, this port doesn’t work.

SPEAKER OUT 8Ω

Connect to external speaker input.

RGB (PC)

Analog PC Connection. Uses a D-sub 15 pin cable

(VGA cable).

AUDIO (RGB/DVI)

1/8” headphone jack for analog PC audio input.

RS-232C IN (SERVICE ONLY)

Used for software updates.

PREPARATION

STAND INSTRUCTION

PREPARATION

Carefully place the TV screen side down on a

cushioned surface to protect the screen from

damage.

Assemble the SSTTAANNDD BBOODDYYto the CCOOVVEERR

BBAASSEEwith the included screws.

Insert the stand as shown.

SSTTAANNDD BBOODDYY

CCOOVVEERR BBAASSEE

■

Image shown may differ from your TV.

GGMake sure the screws in the stand are fully

tightened. (If not tightened fully, the product

could tilt forward and fall). But do not over

tighten, over-tightening can damage the threads

on the screws.

NOTE

DETACHMENT

Carefully place the TV screen side down on a

cushioned surface to protect the screen from

damage.

Remove the four screws that hold the base on.

Detach the stand from TV.

INSTALLATION

x 4

Tighten the stand with the

four screws (provided as parts

of the TV).

Tighten the two of these four screws

and the two Torx plus star head screws

(provided as parts of the TV) to secure the TV. Tighten

the two Torx plus star head screws with a star head dri-

ver bit (not provided as parts of the TV).

x 2 x 2

After removing the stand, install the included

pprrootteeccttiioonn ccoovveerrover the hole for the stand.

Press the PPRROOTTEECCTTIIOONN CCOOVVEERRinto the TV

until you hear it click.

PROTECTION COVER

PREPARATION

CABLE MANAGEMENT

■

Image shown may differ from your TV.

Connect the cables as necessary.

To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Secure the power cable with the PPROTECTIVE

BRACKET/Screw or the Plug in type

Holder(For 32LG700H, 32LG710H model). It

will help prevent the power cable from being

removed by accident.

Install the CABLE MANAGEMENT CLIP as

shown.

If your TV has the CABLE HOLDER, install it

as shown and bundle the cables.

Put the cables inside the CABLE MANAGEMENT

CLIP and snap it closed.

GGDo not hold the CABLE MANAGEMENT CLIP

when moving the TV.

- If the TV is dropped, you may be injured or the

product may be broken.

GGWith some TVs, the PLUG IN TYPE HOLDER

and the CABLE HOLDER are included. If these

holders are inserted into the hole provided on

back of the TV, they cannot be removed.

NOTE

CABLE MANAGEMENT CLIP

CABLE HOLDER

PROTECTIVE BRACKET/Screw

(This feature is not available for

all models.)

PLUG IN TYPE HOLDER

(For 32LG700H,

32LG710H model)

PREPARATION

DESKTOP PEDESTAL INSTALLATION

For proper ventilation, allow a clearance of 4 inches on all four sides.

■

Image shown may differ from your TV.

4 inches

SWIVEL STAND

The TV can be conveniently swivelled on its stand 90° to the left or right to provide the optimum viewing angle.

GGEnsure adequate ventilation by following the clearance recommendations.

GGDo not mount near or above any type of heat source.

CAUTION

PREPARATION

ATTACHING THE TV TO A DESK

The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing

injury or damaging the product.

GGTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installation

instructions. Tipping, shaking, or rocking the TV may cause injury.

WARNING

1-Screw

(provided as parts of the product)

Desk

Stand

4-Screws

(not provided as parts of the product)

GGScrew: M5 x L (

*L: Table depth + 8

~10 mm)

ex) Table depth: 15mm, Screw: M5 x 25

Desk

Stand

PREPARATION

VESA WALL MOUNTING

Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materi-

als, please contact your nearest installer.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.

We recommend that you use an LG brand wall mount when mounting the TV to a wall.

GGDo not install your wall mount kit while the TV is plugged in. It may result in personal injury due to electric

shock.

CAUTION

GGScrew length needed depends on the wall mount

used. For further information, refer to the instruc-

tions included with the mount.

GGStandard dimensions for wall mount kits are shown

in the table.

GGWhen purchasing our wall mount kit, a detailed

installation manual and all parts necessary for

assembly are provided.

GGDo not use screws longer then the standard dimen-

sion, as they may cause damage to the inside to

the TV.

GGFor wall mounts that do not comply with the VESA

standard screw specifications, the length of the

screws may differ depending on their specifica-

tions.

GGDo not use screws that do not comply with the

VESA standard screw specifications.

Do not tighten the screws too much. It may dam-

age the TV or allow the TV to a fall and cause per-

sonal injury. LG is not liable for these kinds of acci-

dents.

GGLG is not liable for TV damage or personal injury

when a non-VESA or non specified wall mount is

used or the consumer fails to follow the TV installa-

tion instructions.

NOTE

GGTo prevent injury, this apparatus must be securely attached to the wall in accordance with the installa-

tion instructions.

WARNING

Product Model VESA

(A *B) Standard Screw Quantity

32LG700H, 32LG710H

37LG700H. 37LG710H

42LG700H, 42LG710H

200 * 100 M4 4

LCD TV 200 * 200

200 * 200

M6 4

PREPARATION

SECURING THE TV TO THE WALL TO PREVENT FALLING

WHEN THE TV IS USED ON A STAND

We recommend that you set the TV close to a wall so it cannot fall over if pushed backwards.

Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,

potentially causing injury or damaging the product.

Caution: Please make sure that children don’t climb on or hang from the TV.

■Insert eye-bolts (or TV brackets and bolts) to attach the product to the wall as shown in the picture.

*If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with screws (sold separately) to the wall. Match the height of the bracket that

is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■Use a sturdy rope or cord (sold separately) to tie the product. It is

safer to tie the rope so it becomes horizontal between the wall and

the product (the less slack in the rope, the better).

■

You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount).

■

Image shown may differ from your TV.

* This feature is not available for all models.

GGUse a platform or cabinet strong enough and large enough to support the size and weight of the TV.

GGTo use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are

the same.

NOTE

( )

ANTENNAANTENNA IN M.P.I.

PREPARATION

ANTENNA OR CABLE CONNECTION

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box

Connection.

For optimum picture quality, adjust the direction if needed.

2. Cable

Wall

Antenna

Socket

Outdoor

Antenna

(VHF, UHF)

Cable TV

Wall Jack

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire

when connecting the antenna.

Copper Wire

■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■If the antenna is not installed properly, contact your dealer for assistance.

■To prevent damage do not connect to the power outlet until all connections are made between the devices.

( )

ANTENNAANTENNA IN M.P.I.

PREPARATION

MPI CARD SLOT / PPV CARD INSTALLATION

1. Remove the two MPI card retainer screws.

2. Pull out current MPI card far enough so that the RF cable can be detached from the old card.

3. Detach RF cable.

4. Place new PPV card into slot and slide it in far enough to reconnect RF cable.

5. Insert card all the way into the slot making sure it is fully seated into back plane connector.

6. Replace the two card retainer screws.

The MPI card is equipped with an RF jack for antenna/cable signal source connection.

The MPI card slot is also available for installing a PPV (Pay-Per-View) card.

MPI Card Removal / PPV Card Installation

RF CABLE

RF cable needs to be

disconnected to remove

the current card.

ANTENNA IN M.PM.P.I.

M.P. I.

Card Slot

PREPARATION

HD RECEIVER SETUP

EXTERNAL EQUIPMENT SETUP

This TV can receive Digital Over-the-air or Digital Cable signals without an external digital set-top box. However,

if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as

shown below.

Component Connection

1. How to connect

Connect the video outputs (Y, PB, PR)of the digital set-

top box to the CCOOMMPPOONNEENNTT IINN VVIIDDEEOOjacks on

the TV. Match the jack colors (Y = green, PB= blue, and

PR= red).

Connect the audio output of the digital set-top box to

the CCOOMMPPOONNEENNTT IINN AAUUDDIIOOjacks on the TV.

2. How to use

■Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

■Select CCoommppoonneennttinput source using the IINNPPUUTT button

on the remote control.

■To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.

■Image shown may differ from your TV.

UPDA

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

RGB

(PC)

AUDIO

(RGB/DVI)

RGB IN

(SER

VIDEO

AUDIO

COMPONENT IN

Y L RP

Y, CB/PB, CR/PR

Supported Resolutions

Horizontal Vertical

Frequency(KHz)Frequency(Hz)

15.73 59.94

15.73 60.00

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

Resolution

720x480i

720x480p

1280x720p

1920x1080i

Signal

480i

480p

720p

108 0 i

108 0 p

Component

Yes

HDMI

Yes

EXTERNAL EQUIPMENT SETUP

HDMI Connection

Connect the digital set-top box to HHDDMMII//DDVVII IINN 11

((DDVVII)) or 22 jack on the TV.

No separate audio connection is necessary.

HDMI supports both audio and video.

1. How to connect

2. How to use

■Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-top box.)

■Select HHDDMMII11or HHDDMMII22 input source with using the IINNPPUUTT

button on the remote control.

HDMI-DTV

RESET

UPDATE

HDMI/DVI IN

1(DVI)

RJP

INTERFACE

VID

RGB

HDMI/DVI IN

1(DVI)

HDMI-DTV OUTPUT

Horizontal Vertical

Frequency(KHz)Frequency(Hz)

31.47 59.94

31.47 60.00

44.96 59.94

45.00 60.00

33.72 59.94

33.75 60.00

Resolution

720x480p

1280x720p

1920x1080i

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

RESET

LAN

(SERVICE ONLY)

RJP

INTERFACE

COMPONENT IN

VIDEO

AUDIO

RGB IN

HDMI/DVI IN

1(DVI)

AUDIO

(RGB/DVI)

DVI-DTV OUTPUT LR

RGB

(PC)

GGA DVI to HDMI cable or adapter is required for this

connection. DVI doesn't support audio, so a separate

audio connection is necessary.

NOTE

Connect the DVI output of the digital set-top box to

the HHDDMMII//DDVVII IINN 11 ((DDVVII))jack on the TV.

Connect the audio output of the digital set-top box to

the AAUUDDIIOO ((RRGGBB//DDVVII))jack on the TV.

1. How to connect

2. How to use

■Turn on the digital set-top box. (Refer to the owner’s man-

ual for the digital set-top box.)

■Select the HHDDMMII11input source on the TV using the

IINNPPUUTTbutton on the remote control.

EXTERNAL EQUIPMENT SETUP

DVD SETUP

Component Connection

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPBPR

Video output ports

on DVD player

B-Y

R-Y

Connect the video outputs (Y, PB, PR)of the DVD to the

CCOOMMPPOONNEENNTT IINN VVIIDDEEOOjacks on the TV.

Match the jack colors (Y = green, PB= blue, and PR= red).

Connect the audio outputs of the DVD to the

CCOOMMPPOONNEENNTT IINN AAUUDDIIOOjacks on the TV.

1. How to connect

2. How to use

■Turn on the DVD player, insert a DVD.

■Select the CCoommppoonneennttinput source on the TV using the

IINNPPUUTTbutton on the remote control.

■Refer to the DVD player's manual for operating instructions.

UPDAT

RESET

LAN

(SERVICE ONLY)

COMPONENT IN

VIDEO

AUDIO

RGB

(PC)

AUDIO

(RGB/DVI)

RGB IN

(SER

VIDEO

AUDIO

COMPONENT IN

Y L RP

1 2

EXTERNAL EQUIPMENT SETUP

HDMI Connection

Connect the HDMI output of the DVD to the

HHDDMMII//DDVVII IINN 11 ((DDVVII)) or 22jack on the TV.

No separate audio connection is necessary.

HDMI supports both audio and video.

1. How to connect

2. How to use

■Select the HHDDMMII11 or HHDDMMII22 input source on the TV

using the IINNPPUUTTbutton on the remote control.

■Refer to the DVD player's manual for operating instructions.

HDMI/DVI IN

1(DVI)

RJP

INTERFACE

VIDEO

RGB

(PC)

HDMI/DVI IN

1(DVI)

HDMI OUTPUT

EXTERNAL EQUIPMENT SETUP

VCR SETUP

Antenna Connection

■To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

ANTENNA IN M.P.I.

( )

Wall Jack

Antenna

Connect the RF antenna out socket of the

VCR to the AANNTTEENNNNAA IINNsocket on the

TV.

Connect the antenna cable to the RF

antenna in socket of the VCR.

1. How to connect

2. How to use

■Set VCR output switch to 3 or 4 and then

tune TV to the same channel number.

■Insert a video tape into the VCR and press

PLAY on the VCR. (Refer to the VCR owner’s

manual.)

Composite (RCA) Connection

Connect the AAUUDDIIOO/VVIIDDEEOOjacks between TV and

VCR. Match the jack colors (Video = yellow, Audio Left

= white, and Audio Right = red)

1. How to connect

2. How to use

■Insert a video tape into the VCR and press PLAY on the

VCR. (Refer to the VCR owner’s manual.)

■Select the AAVV11input source on the TV using the IINNPPUUTT

button on the remote control.

■If connected to AAVV IINN 22, select AAVV22input source on the TV.

GGIf you have a mono VCR, connect the audio cable

from the VCR to the AAUUDDIIOO LL//MMOONNOOjack of the

TV.

NOTE

RS-VIDEO

VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

OPTICAL

DIGITAL

AUDIO OUT

UPDATE

AV IN 1

AUDIO

VIDEO

REMOTE

CONTROL

OUT

SPEAKER

OUT

RS-232C IN

(SERVICE ONLY)

MONO

AV IN 1

AUDIO

VIDEO

MONO

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

AV IN 2

L/MONO

AUDIO

VIDEO

USB

SERVICE ONLY

L R

VIDEO

Camcorder

Video Game Set

Connect the AAUUDDIIOO/VVIIDDEEOOjacks

between TV and external equipment.

Match the jack colors

(Video = yellow, Audio Left = white, and

Audio Right = red)

1. How to connect

2. How to use

■Select the AAVV22input source on the TV using the

IINNPPUUTTbutton on the remote control.

■If connected to AAVV IINN 11input, select the AAVV11

input source on the TV.

■Operate the corresponding external equipment.

EXTERNAL EQUIPMENT SETUP

PC SETUP

GGTo get the best picture quality, adjust the PC graph-

ics card to 1360x768, 60Hz.

GGDepending on the graphics card, DOS mode may

not work if a HDMI to DVI Cable is in use.

GGIn PC mode, there may be noise associated with the

resolution, vertical pattern, contrast or brightness.

If noise is present, change the PC output to anoth-

er resolution, change the refresh rate to another

rate or adjust the brightness and contrast on the

PICTURE menu until the picture is clear.

NOTES

Supported Display Specifications

(RGB-PC, HDMI-PC)

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

VGA (D-Sub 15 pin) Connection

COMPONENT IN

VIDEO

AUDIO

AV IN 1

RS-232C

(SERVICE O

AUDIO

(RGB/DVI)

RGB IN

RGB OUTPUT AUDIO

RGB

(PC)

2. How to use

■Turn on the PC and the TV.

■Select the RRGGBB--PPCCinput source on the TV using the

IINNPPUUTTbutton on the remote control.

Connect the VGA output of the PC to the RRGGBB ((PPCC))

jack on the TV.

Connect the PC audio output to the AAUUDDIIOO ((RRGGBB//DDVVII))

jack on the TV.

1. How to connect

Resolution

720x400

1360x768

640x350

640x480

800x600

1024x768

1280x768

1280x1024

Horizontal Vertical

Frequency(KHz)Frequency(Hz)

31.468 70.09

31.469 70.08

31.469 59.94

37.879 60.31

48.363 60.00

47.776 59.870

47.712 60.015

63.981 60.020

When you use too long RGB-PC cable, there might

be a noise on the screen.

GGAvoid keeping a fixed image on the screen for a

long period of time. The fixed image could become

permanently imprinted on the screen.

GGThe synchronization input form for Horizontal and

Vertical frequencies is separate.

GGDepending on the graphics card, some resolution

settings may not allow the image to be positioned

on the screen properly.

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

RESET

LAN

(SERVICE ONLY)

RJP

INTERFACE

COMPONENT IN

VIDEO

AUDIO

(RGB/DVI)

RGB IN

HDMI/DVI IN

1(DVI)

RGB

(PC)

DVI-PC OUTPUT AUDIO

2. How to use

■Turn on the PC and the TV.

■Select the HHDDMMII11 input source on the TV using the

IINNPPUUTTbutton on the remote control.

Connect the DVI output of the PC to the HHDDMMII//DDVVII IINN

11 ((DDVVII)) jack on the TV.

Connect the PC audio output to the AAUUDDIIOO((RRGGBB//DDVVII))

jack on the TV.

1. How to connect

COMMERCIAL MODE SETUP

COMMERCIAL MODE SETUP FOR MASTER TV

COMMERCIAL MODE SETUP

NNoottee 11: Disconnect all Aux inputs. Under certain conditions, Auto

Tuning (Channel search) is disabled if there is an Aux input active.

Commercial Mode Setup Procedure

1. Set Installer Menu Items

(Enter TV Installer Menu, see Installer menus for detailed instructions.)

a. Set Installer menu item 111177 FFAACCTT DDEEFFAAUULLTT,to

000011and press

EENNTTEERRon Installer remote. (This clears all installer menu custom

settings, channel labels / icons etc. and reloads the factory default

settings.)

b. Set Item 000033 BBAANNDD//AAFFCC.

- BBrrooaaddccaasstt: set to 000000.-

HHRRCC: set to 000022

- CCAATTVV: set to 000011.-

IIRRCC: set to 000033

c. Set item 002288 CCHH OOVVEERRIIDDEEto 000011. This allows access to chan-

nel search, Auto Tuning and Channel List/Edit options in the

Channel Menu.

d. Set other particular installer items that affect your TV programming

network. Enable/Disable Aux sources, set a GGeemm SSttaarrtt CChhaannnneelletc.

e. After all required installer menu item settings have been adjusted,

press ENTER on the remote to remove Installer Menu.

2. Set Up TV Features

(Channel, Picture, Audio, Lock, Time, Option, Digital Captions etc.

See TV Clonable options list and TV menus pages.)

3. Run Auto Tuning (Channel Search)

(Search for all available channels.) Go to the Channel menu and

access the Auto Tuning option, follow onscreen instructions.

a. Edit Channel Scan. In the Channel Menu, access Channel Edit

option.

■Add/Delete channels per your system requirements.

Note: Physical channel numbers are used to identify Virtual channels.

■Add familiar channel trademarks/logos like ABC, CBS, NBC etc. to

the Channel-Time onscreen display. In the Channel menu, select the

Channel Label option. Add identifiable labels (logos) for the end

user to readily know what common networks are available.

4. Transfer TV Setup to Internal TV Controller: 2-5-5 + Menu Mode

After the TV channel scan has been edited and channel label icons

added, enter the Installer menu. Once in the Installer menu, press 2-5-

5 and MENU on the remote. This transfers the TV setup to the inter-

nal controller box.

5 . Add Custom Channel Labels for Analog Channels: 2-5-4 + Menu Mode

Enter Installer menu, press 2-5-4 and MENU. Add your own custom

text labels to channel onscreen displays. Note: Digital Channels often

have a broadcaster generated label. (See 2-5-4+Menu pages.)

When finished, to exit 2-5-4+Menu mode, press MMEENNUU.

Verify TV Setup

At this point, verify that the channel lineup, channel icons and custom

labels are correct. Make sure the TV features are set per your require-

ments. Set item 002288 CChh OOvveerriiddeeto 000000to lock the channel scan.

After the preceding has been completed, the Master TV setup is ready

to be copied to a Clone Programmer, see cloning options pages.

003 BAND/AFC 00X

028 CH. OVERIDE 001

117 FACT DEFAULT 00X

Typical TV Installer Menu

Adjust the settings for

these Installer Menu Items

DIGITAL 19-3

WXYZ

MONO STEREO SAP

Custom Text Label ‘WXYZ’ created in

2-5-4 + Menu (Add Channel Label)

Mode

028 CH. OVERIDE 000

After Master TV setup has been

completed, set item 028 Ch

Overide to 000.

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000 CPU V3.06.00

GEM PTC INSTALLER MENU

093 RJP AVAILABLE 001

Set 093 RJP Available to 001 if

using a remote jack pack

This page provides an overview of a Master TV configuration.

COMMERCIAL MODE SETUP

USB Download Menu

Select a type of sofware to be downloaded:

Upgrade TV Software

Upgrade PTC Software

Teach To TV

Learn From TV

On Master TV, Create Profile and Learn

MASTER TV PROFILE SETUP LEARNING/TEACHING WITH USB

MEMORY CARD

LEARN MODE

Choose the name of the image file:

37LG700H_UA_ a a c c c .TLL

1. Set up all Master TV features on the menus and do

a Channel Search. Add Channel and Aux Labels etc.

Tune in an analog channel.

2. Plug USB memory card into the USB In port on

Master TV.

3. Press Menu key to open Main menu. Highlight the

Option icon.

4. Press the Left arrow key once, the Option icon on

left side of menu will be highlighted.

5. Press number key ‘7’ a total of 7 times.

6. Access to “Learn From TV”.

A. First, Expert Download Menu page will not show

the “Learn From TV”. In order to make “Learn From

TV” available, key in the password which is used to

enter Installer Menu. Example 9-8-7-6.

B. By pressing up/down arrow keys(if there is other

menus), place the cursor on Learn From TV, then

press Enter Key.

7. Using Up/Down arrow key, highlight “Learn From

TV”, then press Enter.

8. To identify the profile from others, you can change

the last 5 digits. Key in a custom file name, then

press the Enter key.

9. The Learning status will be shown on progress bar.

As soon as learning the current profile is complete,

a message will appear on screen indicating the

learning process is done.

10. Remove the USB memory card.

Learn from TV

Learning current profile from master TV:

20%

Don't remove the USB memory card.

Do not unplug!

NOTES

GGDo not remove TV power cord or USB memory

card while Learning, doing so might harm your

USB memory card.

GGDo not remove TV power cord or USB memory

card while Teaching, doing so may cause the TV

to malfunction.

GGYou are allowed to edit the file name, however, a

file with edited contents will not be recognized.

GGSince clock data is copied into USB memory card

as numeric data, the time difference between

teaching and learning is not automatically adjust-

ed. Either set the clock manually, or use Auto

Clock set on TV main menu.

Optional: Edit/Change File Name

If necessary, the file name can be edited or changed.

COMMERCIAL MODE SETUP

1. Plug USB memory card with Master TV Profile setup

into Target TV USB input port.

2. Press Menu key to open Main menu and then high-

light the Option Menu icon.

3. Press the Left arrow key once, this will highlight the

Option icon on left side of menu.

4. Press number key ‘7’, a total of 7 times.

5. Using the Up/Down arrow key, select ‘Teach to TV’,

then press Enter key.

6. Use Up/Down arrow keys to navigate through pro-

files. Select the profile that you want to install by

highlighting it and pressing the Enter key.

7. Teaching progress will be shown on the progress bar.

As soon as teaching is done, a message will appear

indicating that the teaching process has been com-

pleted.

8. When Teaching is done, Remove the USB memory

card and unplug TV power cord.

9. Reconnect TV power cord. Power the TV On and

the master setup should be resident on the TV.

TEACH MODE

Teaching the selected profile to the TV:

20%

Don't remove the USB memory card.

Do not unplug!

On Target TV, Teach Master TV Profile

TEACH MODE

The following software files are found in the memory card.

Select the file you want to download to this TV.

Or, Press EXIT to cancel the upgrade.

Software File List in USB Memory

37LG700H-UA

■

Image shown may differ from your TV.

COMMERCIAL MODE SETUP

TLL-1100A CLONING CONNECTIONS/LEARNING SETUP

Connections for the TLL-1100A Clone Programmer to Learn the TV Master TV Setup

On Master TV

Set up all Master TV features on the

menus and do a Channel Search.

Add Channel and Aux labels etc. See

previous page. Insert MPI cable into

TV MPI port.

On TLL-1100A

1. Turn On the TLL-1100A.

2. Use the Mode button to select

Clone Mode.

3. Use the Left/Right arrow to

select the CBank (1 - 8) to store

the master setup in.

4. Plug the other end of the MPI

cable into the MPI port on the

bottom of the TLL.

5. With the Installer remote control,

select item 1 on TLL menu.

6. Press Enter, to transfer the

Master setup into CBankX on the

TLL. The TLL will copy the master

setup.

7. When learning is done, discon-

nect MPI cable from Master TV.

8. Reconnect TV power cord. Power

the TV On and the master setup

should be resident on the TV.

On Target TV

1. Connect MPI cable from the TLL

to the MPI port on the Target

TV. Assure that the correct

CBank(X) is selected on TLL..

2. With the Installer remote control

select item 2, to Teach the target

TV the master TV setup.

3. Press Enter to begin teaching.

4. When Teaching is done, discon-

nect MPI cable and power the TV

Off. Unplug TV power cord.

5. Reconnect TV power cord. Power

the TV On and the master setup

should be resident on the TV.

Antenna

(or CATV)

Antenna

(or CATV)

TV Link

Loader-Demo

TLL1100A

Ready

TLL1100A

ENTER

RECEIVE SEND

MODE

CLONE SELECTION MENU

Selected Bank: CBank X Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

CLONE CLOCK = 00:00

TV CLOCK = 00:00

THE CLONE IS VERSION V2.2.2

-To change menu items, Press

channel keys or digits.

-To execute item, Press ENTER.

CLONE SELECTION MENU

Selected Bank: CBank X Saved

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

CLONE CLOCK = 00:00

TV CLOCK = 00:00

THE CLONE IS VERSION V2.2.2

-To change menu items, Press

channel keys or digits.

-To execute item, Press ENTER.

M.P.I. Learning Setup

M.P.I. Teaching Setup

TV Link

Loader-Demo

TLL1100A

Ready

TLL1100A

ENTER

RECEIVE SEND

MODE

NOTE

GGIt is assumed that the TV is connected to a signal source, the TV

source selected is Antenna (RF) In, the signal is from an Analog

channel, not a digital channel, all equipment is connected to power

and turned on and the TLL Cloner main menu is displayed on the

TV screen, see above.

GGIf an analog channel is not available, tune TV to an Aux source like

AV-1 for cloning purposes.

GDo not use the TLL-1100A while any PPV card is installed

in TV or clone programmer device will be damaged.

Warning

COMMERCIAL MODE SETUP

LT2002 CLONING CONNECTIONS/LEARNING SETUP

COMMERCIAL MODE SETUP

Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup

Before you begin cloning...

■The Master TV should be connected to a good, stable

signal from an over-the-air antenna or cable service

Analog channel and connected to power. (See above.)

■Teaching and Learning is only possible between iden-

tical model devices. (However, the LT2002 Clone pro-

grammer can store up to 3 different ‘master’ setups.)

WARNING: Copying a blank or incorrect memory into

a TV, STB or other device will cause the TV, STB or

other device to operate erratically or become inopera-

ble.

■Use an Installer’s remote to operate Learning and

Teaching menus.

■Make sure that the batteries in the Clone programmer

are fresh.

■If batteries are removed, the Clone Clock time will be

lost.

■Decide if you want to set the time from the Clone

programmer or copy the time to the Clone program-

mer; from a compatible TV which has the clock set to

the current time.

■Setting the time and transferring it to the Clone or

other device is a separate procedure.

■Follow the connection diagram above to connect the

Clone to a Master TV TV display panel. After learning

is complete, to another identical TV TV display panel

to “teach” it the master setup.

■See the Clone Troubleshooting section to resolve

problems.

Turn to the next page to continue Cloning Setup.

QuickSet II Programmer

LT2002

Ferrite Core

(TDK, ZCAT

2035-0930)

• heartbeat power on

communications ok

• slow power on

no communications

• green battery ok

• red battery low

Blink pattern

Color Reset

Status

Indicator

Connect cable to

TV MPI Jack and

follow on screen

instructions

MPI

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REVISION XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Antenna

or CATV

Master TV

Clone Programmer

GDo not use LT2002 while any PPV card is installed in TV or clone programmer device will be damaged.

Warning

NOTE

GGIt is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the

signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned

on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is

displayed on the TV screen, see above and next page.

GGIf an analog channel is not available, tune TV to an Aux source like AV-1 for cloning purposes.

COMMERCIAL MODE SETUP

LT2002 CLONING LEARNING SETUP

Learning the Master TV Setup

Use MPI Cable to Connect LT2002 Clone

Programmer to Master TV MPI Port

If there is a good connection, “THE CLONE HAS

CONTROL OF TV”

message will appear. Press any key on the Installer remote.

Learn Setup from Master TV

Press 1 to select the “LEARN FROM TV” option, then

press ON/OFF, POWER, or ENTER to go to the Memory

Bank Selection Menu. Pick the Memory ”Bank” you want to

store the master TV’s setup in by pressing either Channel

key repeatedly to choose Memory 1, 2 or 3. (If you

choose a Memory “Bank” that has a master device’s setup

programmed into it, that setup will be overwritten by the

new master TV’s setup.) Once the Clone memory bank is

selected, press ON/OFF, POWER, or ENTER. The Clone

memory bank you have selected will be shown. Press

ON/OFF or POWER to begin copying the master TV’s

setup.

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has

already been copied from a TV into the Clone programmer,

you can set a master TV’s clock by copying the time from

the Clone programmer.) The Clone Programmer can copy

the current time to both a master TV and to the Clone’s

internal clock; accurate to within one minute. (Another rea-

son that the Clone programmer should be equipped with

fresh, high-quality alkaline batteries, is for it to keep the

time as accurately as possible.)

Since the Clone Programmer’s time cannot be set directly,

the current time needs to be copied from a Zenith/LG TV

equipped with M.P.I. input capability.

After the time is copied to the Clone programmer, the cur-

rent time can then be transferred to another TV. (This can

be a master TV, or another TV which has already had the

features set up.)

LT2002 Clone Programmer Communication

Problems

■A slow flashing green light indicates there are

communication problems between the TV and

the LT2002 clone programmer. If this is the

case, check for a damaged cable, poor contacts,

or other connection troubles.

■If the status indicator is red, the programmer

batteries are low and should be replaced. Install

4 high-quality alkaline AA batteries.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REVISION XX

CLONE CLOCK= XX:XX

TV CLOCK= XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER

This menu should appear by itself after

the LT2002 is connected to the TV MPI

port.

This menu should appear after any key is

pressed on the Installer remote.

Instructions for the Clone Programmer to Learn the Master TV Setup

COMMERCIAL MODE SETUP

CLONING CONNECTIONS/TEACHING SETUP

COMMERCIAL MODE SETUP

Teaching the Master Setup to Another TV

Connections for the LT2002 to Teach another TV the Master Setup

Teach Master TV’s Setup to

the target TV

After learning is complete, remove the M.P.I. cable from the mas-

ter TV and connect it to the target TV that you want to copy

the master TV’s setup into. With “THE CLONE HAS CONTROL

OF TV” message displayed, press 2 or use either Channel key to

go to the “TEACH TO TV” option, press ON/OFF, POWER, or

ENTER. Select the LT2002 memory that the new setup is in.

Press On/Off to transfer the new setup and other information to

the new TV. Teaching usually takes 2-3 minutes.

After the “TEACHING COMPLETE” message is displayed, press

any key to return to the Clone menu, then press ON/OFF,

POWER, or ENTER. If finished, detach M.P.I. cable from the

target, newly-cloned TV.

Disconnect TV Power for 15 Seconds

Unplug the AC power cord of the newly-cloned TV from the

power outlet for about 15 seconds to activate the newly-copied

setup.

QuickSet II Programmer

LT2002

• heartbeat power on

communications ok

• slow power on

no communications

• green battery ok

• red battery low

Blink pattern

Color

Reset

Status

Indicator

Connect cable to

TV MPI Jack and

follow on screen

instructions

MPI

Ferrite Core

(TDK, ZCAT

2035-0930)

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XX

THE TV IS VERSION XX

THE SW IS REVISION XX

CLONE CLOCK = XX:XX

TV CLOCK = XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Antenna

or CATV

Target TV Clone Programmer

TEACHING IN PROGRESS,

PLEASE WAIT

TEACHING COMPLETE

This display will appear

after Teaching is complete.

This display will appear

during Teaching function.

CLONE SELECTION MENU

(1) LEARN FROM TV

(2) TEACH TO TV

(3) SET CLONE CLOCK FROM TV

(4) SET TV CLOCK FROM CLONE

(5) DISPLAY TV SETUP

(6) DISPLAY CLONE SETUP

-TO CHANGE MENU ITEMS, PRESS

CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF,

POWER, OR ENTER

This menu should appear

after any key is pressed

on the Installer remote.

NOTE

GGIf an analog channel is not available, tune TV to an Aux source like AV-1 for cloning purposes.

COMMERCIAL MODE SETUP

INSTALLER MENU

Use the Installer’s Menu to set up or change operational settings.

See more detailed descriptions of the Installer menu items on the following pages...

Using the Installer’s Menu

Items 000 ~119 are immediately accessible only upon entering the

Installer’s Menu. Their numbers, descriptions, ranges, factory default

settings, and a place for listing any changes made on-site are given

below and on the following pages.

Typical Installer Menu

Menu Item Function Value Range Default Value Brief Description of Function and Comments

000 INSTALLER SEQ 0 ~3 0 Leave default set to 0.

001 POWER MANAGE 0 ~7 0 Sets number of hours of no activity before auto shut Off.

002 AC ON 0 / 1 0 Set to 1 to enable auto turn On at power up.

003 BAND/AFC 0 ~3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

004 STRT CHANNEL 0 ~127, 255 255 Channel at turn-on (Set to 255 to tune in last channel before power Off).

005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.

007 STRT VOLUME 0 ~63, 255 255 Sets Volume level at TV turn-on (Set 255 to retain last volume level).

008 MIN VOLUME 0 ~63 0 Sets minimum allowable volume setting.

009 MAX VOLUME 0 ~63 63 Sets maximum allowable volume setting.

010 MUTE DISABLE 0 / 1 0 Set to 1 to disable mute function.

011 KEY DEFEAT 0 / 1 0 Set to 1 to disable menu navigation keys on display panel.

015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.

016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.

017 ALARM 0 / 1 1 Set to 1 to enable Alarm.

021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip functions.

022 MAX BLK HRS 0 ~99 12 Sets number of V-Chip (Parental Control) blocking hours.

023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting at power Off.

028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.

029 OLD OCV 0 / 1 0 Set to 1 to change M.P.I. operation to OCV.

030 ACK MASK 0 / 1 0 If set to 1, changes M.P.I. for some OCV boxes.

031 POLL RATE 20 ~169 94 Selects poll rate for M.P.I.

032 TIMING PULSE 186 ~227 207 Sets baud rate for M.P.I.

034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.

000 INSTALLER SEQ 000

UPN 000-000-000-000 FPGA E0F1

PTC V1.00.000 CPU V3.06.00

GEM PTC INSTALLER MENU

Activating changes made to the Installer’s Menu

After exiting the Installer menu, power the TV off and then back on to activate changes to the Installer menu.

Installer Menu Items 000 through 034

Accessing the Installer’s Menu

Make sure TV is on. Installer’s menu items can be accessed by using

an installer’s remote control. Just press MENU repeatedly until the

TV seems to stop responding, then press 9, 8, 7, 6, then ENTER to

access the Installer’s menu. To remove the Installer’s menu, press

ENTER again.

Any changes you make will be stored in nonvolatile

memory. (The menu also disappears automatically.)

The Installer’s menu opens with item 000 INSTALLER SEQ 000.

Use the Up/Down arrow keys to sequence through the available

menu items. Or, access an item directly by keying in the line number,

then pressing MENU. For example, to access the Sleep Timer option

which is item 015, press 0-1-5, then MENU. To change a setting,

use the Left/Right arrow keys. Or, enter a value directly.

COMMERCIAL MODE SETUP

Installer Menu Items 035 through 119

Menu Item Function Value Range Default Value Brief Description of Function and Comments

035 COMPPORT EN. 0 / 1 1 Note 1. Set to 0 to disable HDMI 1. Set to 1 to enable HDMI 1.

038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component Video 1 input jacks.

039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.

040 AUTO CAMPORT 0 / 1 1 Set to 1 to automatically switch to Camport. If set to 1, STRT AUX

SRCE cannot be set to 2.

046 STRT AUX SRCE 1 ~6, 255 6 Sets the starting AUX source.

047 AUX STATUS 0 / 1 0 Set to 1 for M.P.I. AUX source to be reported as a channel number

instead of Channel 0.

053 DIS. CH-TIME M. 0 / 1 0 Set to 1 to disable Channel-Time display.

069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.

070 FOR. CH-TIME 0 ~7 2 Chooses custom foreground color for the Channel-Time display.

071 BCK. CH-TIME 0 ~7 2 Chooses custom background color for the Channel-Time display.

073 CH NOT AVBLE 0 / 1 0 If set to 1 and channel override is 0, “NOT AVAILABLE” message is

displayed when directly accessing a channel not in the favorite channel list.

075 REVERT CH 0 / 1 0 If set to 1 and loss of M.P.I. communication occurs, TV tunes to Start Channel.

078 UPN MSB 0 ~255 0 User programmable number, most significant byte.

079 UPN MSB-1 0 ~255 0 User programmable number, most significant byte - 1.

080 UPN MSB-2 0 ~255 0 User programmable number, most significant byte - 2.

081 UPN LSB 0 ~255 0 User programmable number, least significant byte.

082 CHKSM ERROR 0 / 1 1 Enforces rigid M.P.I. checksum.

083 HANDSHK TIME 0 ~5 5 Relaxes M.P.I. timing to be compatible with PC based

Windows-controlled systems.

084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block

permanent.

087 REAR RGB EN. 0 / 2 / 18 2 Note 1. Set to 0 to disable RGB1. Set to 2 for PC.

088 EN NOISE MUTE 0 / 1 1 If set to 1, mutes audio if no signal is present.

090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.

091 YPrPb2 0 / 1 1 Set to 0 to disable HDMI 2. Set to 1 to enable HDMI 2.

093 RJP AVAILABLE 0, 1, 2, 5, 6 0 Set to 0 to disable. Set to 1, 2, 5 or 6 for HDMI or DVI mode. (See

detailed descriptions)

094 SAP MENU EN 0 / 1 1 Set to 0 to disable feature on Function menu. Set to 1 to enable feature

on Function menu.

096 DEF. ASP. RATIO 0 ~5 2 Sets default aspect ratio at power up. See detailed descriptions

and item 106.

099 BACK LIGHTING 1 ~100 Sets the brilliance of the TV picture backlighting.

101 ~200 255 Settings above 101 control dynamic back lighting and enable

201, 202, 255 power saving mode.

102 ATSC BAND 0 ~4 4 Selects ATSC band.

103 ATSC TUNE MODE 0 / 1 1 Default 01 for physical channel scan. Set to 0 for Virtual Channel scan.

104 START MINOR CH 0 ~255 0 Selects Minor start channel. Set 0 for NTSC. Not 0, sets Minor

channel number.

106 ASP RATIO LOCK 0 / 1 0 To retain set aspect ratio on power cycle, set to 1. Set to 0 for

default ratio on power cycle.

116 VIDEO MUTE EN 0 / 1 0 Set to 0 for normal, set to 1 for Blank.

117 FACT DEFAULT 0 / 1 0 0=Normal. 1=Loads presets of all above settings.

118 POWER SAVING 0 / 1 1 Set to 0 to disable power saving mode.

119 GEM STRT CH 0 ~ 135 0 Sets the GEM Start Channel.

NNoottee 11: Dependent on item 093 RJP Available setting.

COMMERCIAL MODE SETUP

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Specifies entry sequence to the Installer Menu.

0 = 9876 1 = 4321

2 = 1478 3 = 3698

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff.

The POWER MANAGE function is for saving energy. If

set to 0, Power Manage is Off. Settings range from 0 ~ 7,

with 1 ~7 representing the hours that the unit will

remain On, unless there has been activity from either the

control panel or remote control.

002 - AC ON (AC Power Switchable)

If set to 1, allows the TV to turn On just by applying

AC power. Pressing the On button is not necessary. This

is desirable if the TV is plugged into a cable box or a

power outlet controlled by a wall switch. Use ADJ

Left/Right arrow to choose 0 or 1 where 0 is the

default is Off, and 1 is On.

NOTE: If set to 1 (On), the TV does not respond to

On/Off commands from either the remote or the dis-

play control panel, and the SLEEP TIMER is also non-

functional.

003 - BAND/AFC (Band/Automatic Frequency

Control)

There are 4 possible settings for this option:

0 = Broadcast 1 = CATV

2 = HRC 3 = IRC

If some channels were not found by Auto Tuning

(Channel Search), select the appropriate Band setting

here and add the channels using the Channel Edit

option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial

channel number when the TV is turned On. This feature

is useful for an in-house information channel, since the

TV would always select that channel when it is turned

On. Setting this to 255 causes the last channel viewed

when the TV was turned Off, to be the tuned to chan-

nel when the TV is turned On again. Note: For a digital

Start Channel, always remember to set item 104 to the

Minor Start Channel number.

255 = Last channel 1 ~125 = Ch X 0 = Aux

126 Map to Channel 3. 127 Map to Channel 4.

005 - CHAN LOCK (Channel Lock)

CHAN LOCK is ideal if the system must always be on

the same channel. Changing channels with Channel

Up/Down or keypad numbers is impossible. Channel

Lock is inactive if set to 0 (default).

Generally, this feature is used in connection with START

CHANNEL (Installer item 004) where the start channel

may, for example, be set to 3 or 4. If the start channel

is 3, then the TV will remain locked on Channel 3.

NOTE: For Items 007, 008 and 009

For legacy reasons, the scale used is 0 - 63. The PTC

software will translate this to the 0 - 100 scale used by

the TV.

To translate a TV volume level to the installer menu

value, use the following formula:

Installer Value = TV Value x 63

10 0

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial

volume level setting when the TV is turned On. This fea-

ture is useful for an in-house information channel, since

the TV would always select that volume level when it is

turned On. The range of values are 0 - 63, 255. If 255

is selected, the current volume level will be retained in

memory when the TV is turned Off; at turn On, the vol-

ume level will be automatically set at the previous or

last level.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level

allowable with the VOLUME (VOL) Up/Down control. In

this way, for example, someone cannot set the volume

too low to hear. The value range is from 0 to 63 —

change values with ADJ Left/Right arrow. The factory

default is 0, which provides the full range of volume

control, if item 009 MAX VOLUME is also set to 63. It

may be best to set the same value on every TV.

NOTE: The minimum volume level cannot have a value

setting higher than the MAX VOLUME level (described

below).

COMMERCIAL MODE SETUP

023 - CAPTION LOCK

Set to 1 to restore previous caption On/Off state after

turn Off. If set to 0, captions are always Off at turn

On.

028 - CH. OVERIDE (Channel Override)

If set to 1, the user can select channels with either

Channel up/down or by direct keypad entry. If set to

0, only those channels that are entered for scanning

can be selected.

029 - OLD OCV (On Command VideoTM)

Set to 1 for operation with systems from On

Command Corporation.

030 - ACK MASK

M.P.I. Communication Parameter. Leave at default set-

ting unless changed by Pay-Per-View provider. When set

to 1, changes M.P.I. for some OCV boxes.

031 - POLL RATE

M.P.I. Communication Parameter. Selects Poll Rate for

M.P.I. Leave at default setting unless changed by Pay-

Per-View provider. Step size of 16 ms.

032 - TIMING PULSE

M.P.I. Communication Parameter. Leave at default set-

ting unless changed by Pay-Per-View provider. Sets

baud rate. Step size of 4.3 uS.

034 - CAMPORT EN. (Camera Port Enable)

Set to 1 to enable Video 2 input on display panel. If

set to 0, Video 2 input on display panel is not func-

tional.

NOTE: S-Video overrides Video jack.

035 - COMPPORT EN. (Computer Port Enable)

Enable/disables display panel HDMI1 input jack. Set to

0 to disable, set to 1 to enable.

NOTE: The setting above is ignored if Installer item

093 RJP AVAILABLE, is set to 1.

038 - YPrPb EN. (Rear Component Video Enable)

Set to 1 to enable display panel rear Component

Video input jacks.

Set to 0 to disable display panel rear Component

Video input jacks.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear AUX (Video 1) input.

Set to 0 to disable display panel rear AUX (Video 1)

input.

Note: S-Video overrides Video.

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level

allowable with the VOLUME (VOL) Up/Down controls.

In this way, for example, someone can not set the vol-

ume level high enough to disturb others. The value

range is 0 to 63, with 63 as the default, which gives the

user the full range of volume control, if item 008 MIN

VOLUME is also set at 0. Change values with ADJ

Left/Right arrow keys. It may be best to set the same

value on every TV.

NOTE: The maximum volume level cannot have a value

setting lower than the MIN VOLUME level (described

previously).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1,

sound cannot be muted. If set to 0, sound can be

muted.

011 - KEY DEFEAT (Keyboard Defeat)

If set to 1, key defeat prevents the end user from

accessing the on-screen menus with the display front

panel—MENU, SELECT, and Left / Right arrow keys do

not function. If set to 0, those keys do function.

NOTE: The menus can always be accessed by pressing

MENU on the remote.

015 - SLEEP TIMER

If set to 1, the SLEEP TIMER feature may be used. If

set to 0, the Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers) *

If set to 1, Timer function is available to user and

enabled continuously. Set to 0 to disable On/Off

Timers. (Clock must be set in order to use Timers.)

017 - ALARM *

Gives the installer the option of making the Alarm

function available to the end user. If set to 1, Alarm

function is available to end user. Set to 0 to disable

the Alarm function.

NOTE: Clock must be set before the Alarm function

will work.

021 - V-CHIP (Parental Control) *

Set to 1 to activate V-Chip (Parental Control); have it

available to end user to filter and control or otherwise

restrict programming content that can appear. Set to 0

to turn V-Chip feature Off, not available to user; no

programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours) *

Sets hours from 0 to 99 for the maximum V-Chip

(Parental Control) block hours. Default setting is for

12 blocking hours.

**OOnnllyy aaffffeeccttss FFuunnccttiioonn MMeennuu iiff eennaabblleedd bbyy

ssoommee PPPPVV pprroovviiddeerrss..

COMMERCIAL MODE SETUP

073 - CH NOT AVBLE (Channel Not Available)

If set to 1 and item 028 CHANNEL OVERRIDE is set to 0,

“NOT AVAILABLE” message is displayed when directly

accessing a channel not in the channel scan list available in

memory.

075 - REVERT CH (Revert to Start Channel)

If set to 1 and loss of M.P.I. communication occurs, TV auto-

matically tunes to the specified Start Channel.

078 - UPN MSB (UPN Most Significant Byte)

User programmable number, most significant byte readable

by M.P.I. command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Significant Byte-1)

User programmable number, most significant byte-1 read-

able by M.P.I. command. Not linked to serial number.

080 - UPN MSB-2 (UPN Most Significant Byte-2)

User programmable number, most significant byte-2 read-

able by M.P.I. command. Not linked to serial number.

081 - UPN LSB (UPN Least Significant Byte)

User programmable number, least significant byte readable

by M.P.I. command. Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)

Enforces rigid M.P.I. checksum validation.

Set to 1 for validation.

Set to 0 to disable (does not check checksum on M.P.I.

async port). SPI is always checked.

083 - HANDSHK TIME (Handshake Time)

Adds an additional delay to the handshake time which is 64

msec, thus relaxing M.P.I. timing requirements to be compati-

ble with PC based Windows controlled systems, range is 0 -

(Timeout = 25.5MS + [25.5 MS* Handshake time]).

084 - PERMANENT BLK (Permanent Block)

Allows Lock (Parental Control) blocking schemes to be per-

manent by disabling the blocking hours function.

Set to 1 to install Parental Control restrictions permanently.

Set to 0 for user-specified hours control of blocking

schemes.

087 - REAR RGB EN. (Rear RGB Enable)

Controls access to rear RGB input on TV.

Set to 0 to disable RGB input.

Set to 2 for PC for STB RGB input.

Set to 18 for Auto Configure one time only with power

cord removal and reinsertion.

088 - EN NOISE MUTE (Enable Noise Mute)

If set to 1, audio mutes if no signal is present.

090 - KEY LOCK

If set to 1, display panel keyboard is locked out, not available

to end user. IR receiver remains functional.

040 - AUTO CAMPORT

Set to 1 to automatically switch to Camport when equip-

ment is connected to front Video input.

Set to 0 to disable front Video automatic source selection.

NOTE: If set to 1, 093 RJP Available is automatically set to 0.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting AUX source. At power up, TV will tune to

starting Aux source if item 004 Start Channel is set to 0.

If item 093 RJP Available is set to 0 and item

040 Auto Camport is set to 0:

1 = Video 1 4 = RGB 255 = Last Aux

2 = Video 2 5 = HDMI 2

3 = HDMI 1 6 = Component

If item 093 RJP Available is set at 1:

2 = Video 2 5 = HDMI 2 6 = Component

If item 040 Auto Camport is set to 1:

1 = Video 1 5 = HDMI 2

3 = HDMI 1 6 = Component

4 = RGB

047 - AUX STATUS

Set to 1 for M.P.I. AUX source to be reported as a channel

number instead of channel 0. Set to 0 to disable AUX iden-

tification change. Controls M.P.I. status channel response for

AUX inputs.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display, Channel-Time

display will not appear.

Set to 0 to enable the Channel-Time display.

069 - EN. CH-T COL. (Enable Channel-Time Custom

Color)

Set to 1 to enable custom color for the Channel-Time dis-

play.

Set to 0 to disable custom color for the Channel-Time dis-

play.

070 - FOR. CH-TIME (Channel-Time Display Foreground

Color)

Set according to Color Chart.

0 = Black 3 = Yellow 6 = Cyan

1 = Red 4 = Blue 7 = White

2 = Green 5 = Violet

NOTE: If foreground and background color are the same,

menu background is transparent.

071 - BCK. CH-TIME (Channel-Time Display

Background Color)

Set according to Color Chart.

0 = Black 3 = Yellow 6 = Cyan

1 = Red 4 = Blue 7 = White

2 = Green 5 = Violet

NOTE: If foreground and background color are the same,

menu background is transparent.

COMMERCIAL MODE SETUP

100

COMMERCIAL MODE SETUP

Set to 202, TV automatically controls backlighting

depending upon external spectral sensitivity and picture

level of the current program.

Set to 255, to disable power saving mode.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:

0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC.

103 - ATSC TUNE MODE

Sets ATSC tuning mode: Default set to 1 for Physical chan-

nel scan.

Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets XX-XX minor start channel number at power up:

0=NTSC. If not 0, number selected is the Minor start

channel number.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power Off.

Set to 0 to retain default aspect ratio with power Off. See

item 96 Default Aspect Ratio above.

116 - VIDEO MUTE EN (Video Mute Enable)

Set to 0 for normal.

Set to 1 for blank.

117 - FACT DEFAULT (Factory Default)

Set to 0 for normal.

Set to 1 to load presets to all of the previous item settings.

WARNING: Setting this to 1 will reload the fac-

tory defaults and clear the channel list includ-

ing erasing any assigned Channel Icons and

custom channel Labels.

118 - POWER SAVING

Default is set to 1, power saving mode is enabled.

Set to 0 to disable power saving mode.

■Power Saving is only active when TV is in standby

mode.

■Power Saving is not available in normal power on mode.

If Power Saving is disabled and TV is in Standby mode with

External card installed: TV can supply 12V (12 Watts) to

External card and Standby power consumption will be nor-

mal.

119 - GEM START CH (Gem Start Channel)

Sets the Gem start channel. Set the channel number that

will provide Gem data to the TV at turn on. Initially the TV

may take several minutes to load program data from AC

power off state.

091 - YPrPb2 (HDMI2 Enable)

Set to 0 to disable display panel HDMI2 input.

Set to 1 to enable DTV mode. Set to 2 to enable PC

mode.

093 - RJP AVAILABLE (Remote Jack Pack Available)

0 = Remote jack pack is not available or disabled.

1 = Legacy Model RJPs: HDMI Mode

Enables RJP when an HDMI cable is inserted into RJP.

Video is from HDMI. Audio stream is expected from HDMI

source. If no audio is present, no audio will be heard.

2 = Legacy Model RJPs, DVI Mode

Enables RJP when an HDMI cable is inserted into RJP.

Video is from HDMI however, Audio is from selected audio

source, based on the RJP’s audio hierarchical priority.

5 = Scaler Model RJPs, HDMI Mode

Enables RJP when an HDMI cable is inserted into RJP.

VIdeo is from HDMI. Audio stream is expected from HDMI

source. If no audio is present, no audio will be heard.

6 = Scaler Model RJPs, DVI Mode

Enables RJP when an HDMI cable is inserted into RJP.

Video is from HDMI however, Audio is from selected audio

source, based on the RJP’s audio hierarchical priority.

Notes :

■See Reference section, RJP Input Hierarchy and RJP

Models page.

■If set to 1, 2, 5 or 6, item 040 Auto Camport is auto-

matically set to 0.

Settings 1, 2, 5 and 6 allow the lodge staff to customize

each TV’s RJP setup based on customer requirements.

094 - SAP MENU EN (2nd Audio Program)

Set to 1 to enable SAP feature on Function menu, if

Function menu is available.

Set to 0 to disable SAP feature on Function menu, if

Function menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio)

Selects default aspect ratio at power up, see settings below.

Set to 0 “Set By System”.

Set to 1 for 4:3.

Set to 2 for 16:9 (Factory Default).

Set to 3 for Horizon

Set to 4 for Zoom 1

Set to 5 for Zoom 2

099 - BACK LIGHTING

Sets the TV screen brightness at power up, see settings

below.

Default setting value is 255.

1 - 100 Static Backlighting.

(1 = Dimmest picture, 100 = Brightest picture.)

101 - 200 Dynamic Backlighting.

(101 = Dimmest picture, 200 = Brightest picture.)

201 Automatic Static Backlighting

202 Automatic Dynamic Backlighting

Set to between 101 and 200, TV automatically controls

backlighting depending upon the picture level of the cur-

rent program.

Set to 201, TV automatically controls backlighting

depending upon external spectral sensitivity.

COMMERCIAL MODE SETUP

101

REFERENCE: DETAILED INSTRUCTIONS FOR MAKING A

MASTER TV

IMPORTANT INSTALLER SETUP INFORMATION! PLEASE READ THE FOLLOWING...

To set up a master TV you will need to know

how to enter the TV Installer menu and make

changes to the default values as required. If

necessary, familiarize yourself with the TV

Installer menu and how to make and save changes in the

menu, beforeattempting to clone the TV Master TV

setup.

You will also need an LLGG IInnssttaalllleerr rreemmoottee ccoonnttrrooll

similar to the one shown in the front of this manual. The

installer remote must have a “Source” button or its equiv-

alent. The remote shown in this manual has a “INPUT”

button -- this button serves the purpose of a Source but-

ton.

Finally, the TV’s clonable features need to be set up. This

is a critical step. If the Master TV display panel’s clonable

features like adding channel icons or channel labels, digi-

tal font options etc., are not correctly added, then the

cloned TVs will all have problems.

As the cloning procedure is being performed, specific

steps need to be done at the indicated times to achieve

the desired result. Be sure to do each task as indicated. If

a procedure or step is left out or not performed com-

pletely, cloning may not work. At each step, pay attention

to assure the TV screen shows the proper message when

cloning. If the message indicated does not appear, there

is a problem with that step and cloning may not be suc-

cessful. Cloning is only possible when the signal source is

an Analog channel, not a digital channel.

Detailed Instructions

The following describes the procedure for preparing a

Master TV for cloning and the procedure for adding

Channel Icons and/or Labels.

Note 1: Disconnect all Aux inputs. Under certain condi-

tions, Auto Tuning Channel Search is disabled if there is an

Aux input active.

Note 2: Under certain conditions, changes to the input

mode of the RGB inputs will not take effect until the power

is cycled (TV is turned Off and On). To avoid confusion, dis-

connect all RGB inputs before entering the Installer menu.

1. Enter the TV installer menu.

a. Reset the internal controller to factory default by

accessing installer menu item 117 FACT DEFAULT, set it

to 1 and press “ENTER”. The value will change back to 0

after the TV’s internal controller has been restored to

factory default condition. This step will ensure that the

TV channel memory will be the active channel list. Check

the Status LED. If it is blinking rapidly then the TV chan-

nel map is in use.

b. Within the Installer menu, set the Installer menu items

to the configuration required of your institution.

c. It is important to set the tuning band at this time, see

Installer menu item 03 BAND/AFC.

d. Set Installer menu item 28 – CH OVERIDE to 001 to

allow access to the Auto Tuning and Ch. Edit features in

the Channel Menu. Exit the Installer menu.

2. Access the Master TV menus and set the clonable

options on the menus to the desired configuration.

Refer to the Clonable Menu Features Chart in this man-

ual.

3. Run Auto Tuning to find analog and digital channels.

4. Enter the Channel Edit menu and edit the channel lineup

to include the Free-To-Guest Channels only.

5. Assign ICONs to the channels using the Channel Label

Menu.

Note: You can add Channel ICONS typically network

logos like ABC, NBC, PBS etc. in this step. Or, in Step 7,

add Channel ICONS or labels for channels without Icons.

6. Transfer the TV setup: Enter the TV installer menu. Press

‘2’, ‘5’, ‘5’, ‘MENU’ to start the transfer of the TV’s setup

to the internal controller. Once the transfer is complete,

the system will exit the Installer menu. Check the Status

LED inside the TV. It should be blinking slowly (1 blink

per second).

7. Edit/Add Channel ICONs and Channel Labels as needed.

Enter Installer menu. With menu displayed, press 2-5-4

+ MENU. See next page for detailed instructions:

- Editing/Adding Channel ICON and Labels on

Master TV

- Changing a Channel’s ICON on Master TV

- Changing/Adding Channel Labels on Master TV

- Changing Source Labels on Master TV

8. Verify Master TV setup and feature configuration:

■Did you add Channel ICONS?

■Did you add Channel Labels?

■Did you add Source Labels?

■Did you adjust all TV menu options as required?

After verifying master setup, enter the TV Installer menu

and set Installer menu item 28 CH OVERIDE to 000.

Press ENTER to remove and exit the Installer menu.

Making a Master TV

COMMERCIAL MODE SETUP

102

REFERENCE: PROCEDURES FOR ADDING CHANNEL LABEL

ICONS/CUSTOM CHANNEL LABELS (2-5-4 + MENU MODE)

COMMERCIAL MODE SETUP

Adding Channel Icons and Labels in the 2-5-4 + Menu Mode

Editing/Adding Channel ICONs and/or

Labels

If there is no pre-assigned ICON, you can make a cus-

tom channel label of up to 7 characters to help in

identifying the channel or network. At your option,

channel labels can also be added in addition to a pre-

assigned ICON. You may also add labels for the Aux

input sources to clearly identify the devices that are

connected to the Aux inputs.

Editing and adding the labels can only be done if there

are channels entered into the TV’s channel map either

by using the method described in item 6 (page 18), by

cloning or by the use of the master remote control

from the PPV provider.

Note: A blank letter space is available between ‘Z’ and

‘!’.

To Do Channel Editing/Labeling, Proceed as

Follows

1. Enter TV Installer menu.

2. Once the installer menu appears, press ‘2’, ‘5’, ‘4’,

‘MENU’. This enters the channel label editing mode.

Add your channel icons and channel labels in this

menu, see below. (You can do this more than once.)

3. To exit the menu when done press “MENU”.

1234567

XYZ

NETWORK

(Icon)

(Label)

Changing a Channel’s ICON on

Master TV

1. With Channel Up/Down, select the

channel you want to change the

Icon for.

2. With the Right or Left ADJ arrow,

select the thin letter ‘I’ on the

channel ID display.

3. With the Up or Down arrow, select

the desired ICON you want to

appear to identify the channel. (If

you know the ICON number, enter

the number followed by Enter /

Select.)

4. Proceed with Changing/Adding

Labels or go to the next channel.

Changing/Adding Channel

Labels on Master TV

1. Channel Up/Down to select the

desired channel.

2. Press the Right or Left ADJ arrow

repeatedly until the numbers 1 to

7 show up. The number shows the

position of the character that can

be changed. Number 1 is the first

character, number 2 the second

character and so on.

3. With the Up or Down arrow, select

the desired character.

4. Proceed to the next number posi-

tion or use Channel Up/Down to

go to the next channel.

Changing Source Labels on

Master TV

1. Press “INPUT” to select the desired

Aux input source; A/V 1, A/V 2,

HDMI Component, RGB etc.

2. Press the Right or Left arrow

repeatedly until the numbers 0 to 9

shows up. The number shows the

position of the character that can

be changed.

3. Use the Up or Down arrows to

select the desired character.

4. Press “INPUT” for the next Aux

source or proceed with Changing

Icon or Changing/Adding Labels.

Press Ch Up/Down to return to

channels.

■CHANNEL Up/Down - Tunes in the next channel in

scan.

■Left/Right Arrows - Select the item to change. If “I”

is shown, the ICON can be changed. If a number is

shown, it indicates the position of the character that

can be changed.

■Up/Down Arrows - Select the ICON or the charac-

ter to be displayed. Tip: Arrows can be held down for

fast scrolling.

■0 – 9 - Use to enter the index number of the ICON,

if known.

■ENTER/SELECT - Changes the ICON after the

number has been entered.

■INPUT - Changes the Aux input label. (“Source” on

the remote shown in this manual is INPUT.)

■MENU - Exits the editing process.

Installer Remote Control Key Functions for Master TV Channel

Editing/Labeling Menu

COMMERCIAL MODE SETUP

104

REFERENCE: POWER SAVING SETUP

COMMERCIAL MODE SETUP

Power Savings Setup

Installer Item 118 Power Saving: set to 001, enabled (Default).

Installer Item 099 Backlighting: value set as shown below. (Default value is 255)

Note: Values are results of controlled experiments under laboratory conditions.

Item 099 Picture Power Power Item 099 Picture Power Power

Backlighting Lumin. Consumption Savings Backlighting Lumin. Consumption Savings

(Static) (Watts) Rating (Dynamic) (Watts) Rating

100 206 104 0 % 200 103 74 28.85 %

90 204 103.5 0.48 % 190 96 73 29.81 %

80 203 103 0.96 % 180 84 69.5 33.17 %

70 172 93 10.58 % 170 73 65.5 37.02 %

60 147 85 18.27 % 160 64 62 40.38 %

50 127 79 24.04 % 150 57 60 42.31 %

40 108 73.5 29.33 % 140 51 57.5 44.71 %

30 86 67 35.58 % 130 44 55 47.12 %

20 66 60 42.31 % 120 38 52.5 49.52 %

10 50 55.5 46.63 % 110 33 50.5 51.44 %

1 39 51.5 50.48 % 101 29 49 52.88 %

For 32LG700H, 32LG710H

Note: Values are results of controlled experiments under laboratory conditions.

Item 099 Picture Power Power Item 099 Picture Power Power

Backlighting Lumin. Consumption Savings Backlighting Lumin. Consumption Savings

(Static) (Watts) Rating (Dynamic) (Watts) Rating

100 258 151.5 0 % 200 93 91.5 39.60 %

90 230 136.5 9.90 % 190 79 85.5 43.56 %

80 201 122.5 19.14 % 180 67 80 47.19 %

70 170 111 26.73 % 170 58 74.8 50.63 %

60 145 101.3 33.14 % 160 50 70.8 53.27 %

50 120 91.5 39.60 % 150 44.5 67.5 55.45 %

40 95 81.3 46.34 % 140 38 63.5 58.09 %

30 72 71 53.14 % 130 31.5 59.3 60.86 %

20 54 63.5 58.09 % 120 27 56.5 62.71 %

10 41 58 61.72 % 110 23.5 54.5 64.03 %

1 31 53 65.02 % 101 21 52.8 65.15 %

For 37LG700H, 37LG710H

108

APPENDIX

TROUBLESHOOTING

APPENDIX

TThhee ooppeerraattiioonn ddooeess nnoott wwoorrkk nnoorrmmaallllyy..

TThhee vviiddeeoo ffuunnccttiioonn ddooeess nnoott wwoorrkk..

No picture &No sound

No or poor color

or poor picture

Poor reception on

some channels

Lines or streaks

in pictures

No picture

when connecting HDMI

Horizontal/vertical bars

or picture shaking

Picture appears slowly

after switching on

The remote control

doesn’t work

Power is suddenly

turned off

■Check to see if there is any object between the product and the remote control

causing obstruction. Ensure you are pointing the remote control directly at the TV.

■Ensure that the batteries are installed with correct polarity (+ to +, - to -).

■Ensure that the correct remote operating mode is set: TV, VCR etc.

■Install new batteries.

■Is the sleep timer set?

■Check the power control settings. Power interrupted.

■Check whether the product is turned on.

■Try another channel. The problem may be with the broadcast.

■Is the power cord inserted into wall power outlet?

■Check your antenna direction and/or location.

■Test the wall power outlet, plug another product’s power cord into the outlet

where the product’s power cord was plugged in.

■This is normal, the image is muted during the product startup process. Please

contact your service center, if the picture has not appeared after five minutes.

■Adjust Color in menu option.

■Try unplugging any others electronics that are near by to see if interference is

causing the problem.

■Try another channel. The problem may be with the broadcast.

■Are the video cables installed properly?

■Activate any function to restore the brightness of the picture.

■Check for local interference such as an electrical appliance or power tool.

■Station or cable product experiencing problems, tune to another station.

■Station signal is weak, reorient antenna.

■Check for sources of possible interference.

■Check antenna (Change the direction of the antenna).

■Check HDMI cable over version 1.3.

If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no

screen display. In this case use the latest cables that support HDMI version 1.3.

APPENDIX

109

TThheerree iiss aa pprroobblleemm iinn PPCC mmooddee.. ((OOnnllyy PPCC mmooddee aapppplliieedd))

■Adjust resolution, horizontal frequency, or vertical frequency.

■Check the input source.

■Run the Auto configure or adjust clock, phase, or H/V position. (Option)

■Check the signal cable.

■Update video card drivers.

The signal is out of range

Screen color is unstable

or single color

Vertical bar or stripe on

background &

Horizontal Noise &

Incorrect position

Picture OK but No sound

Unusual sound from

inside the product

No sound

when connecting HDMI

or USB

No output from one

of the speakers

TThhee aauuddiioo ffuunnccttiioonn ddooeess nnoott wwoorrkk..

■Press the VOL or VOLUME button.

■Sound muted? Press the MUTE button.

■Try another channel. The problem may be with the broadcast.

■Are the audio cables installed properly?

■Adjust Balance in menu option.

■A change in ambient humidity or temperature may result in an unusual noise

when the product is turned on or off and does not indicate a fault with the

product.

■Check HDMI cable over version 1.3.

■Check USB cable over version 2.0.

*This feature is not available for all models.

EErrrraattiicc OOppeerraattiioonn

Installer menu setup ■Adjust Installer menu settings as required.

PPoowweerr

No Power ■See troubleshooting flow chart.

SSooffttwwaarree PPrroobblleemmss

Cannot direct enter chan-

nel number or “No Signal”

appears

■After 2-5-5 + MENU, only channels included in TV controller will appear. If chan-

nel is available it can be added to channel scan, rescan channels. If it is not avail-

able, the ‘No Signal’ message appears on the TV screen.

NOTE

GGFor other problems not caused by the TV, refer to other devices’ operating guides.

APPENDIX

110

REFERENCE: LT2002 CLONING PROCEDURE

TROUBLESHOOTING

Reset Clone After Static Shock

After replacing exhausted batteries, or if the program-

mer behaves strangely after a static shock, use a paper

clip or similar instrument inserted through the small

hole marked ”RESET” to activate the internal reset

switch and restore normal operation. After a reset,

check the real-time clock setting. It may be necessary

to reset the Clone Programmer clock from a TV con-

taining the correct time.

Note

The LT2002 programmer is designed to be used with

TVs containing the 221-01006 and later processors.

Use with earlier TV sets may give unpredictable results.

Processors used before the 221-01006-04 have a lim-

ited screen display capability. They cannot display

entire screens as shown in the quick setup instructions

accompanying the LT2002 clone programmer. Use the

printed menu illustrations on the quick setup sheet

supplied with the Clone as an aid to making your pro-

gramming choices. (Although the menus are not all dis-

played, the clone functions all operate normally.)

Clone Programmer Troubleshooting

Warning: Do not use LT2002 while any PPV card is

installed in TV or clone programmer will be damaged.

32LG3DCH

(32LG3DCH-UA)

32LG3DC

(32LG3DC-UA)

■After cloning operations are complete, just unplug the LT2002 from the TV.

■If the TV does not display a picture on the TV (blank screen) after a few seconds, just change channels.

CClloonnee PPrrooggrraammmmeerr

■Press Reset on clone programmer, redo teach/learn. (Teach/Learn should take a

minimum of 1 minute.)

■ Only use an LG Installer remote to operate clone programmer with TV.

■Connect M.P.I. cord properly, assure good connection.

■TV must be powered On for clone to work.

■Install 4 fresh AA high-quality alkaline batteries.

■Connect TV to a reliable Analog channel signal source.

■Set time on a TV, copy time to Clone Programmer.

■Try a different LT2002 Clone programmer.

■Reset Clone Programmer.

■Retry cloning again.

Clone copies Setup in less

than 30 seconds

LED does not blink

Remote does not operate

clone

Clone menu hard to read

No time set

Clone not working

Clone Scans Channels

more than once

32LG3DCH

(32LG3DCH-UA)

32LG3DC

(32LG3DC-UA)

MMaasstteerr aanndd OOtthheerr TTVVss

■Wait until procedure complete message is displayed.

■Cloning is only possible with identical model TVs.

■Reread cloning pages to be sure all tasks were performed.

■Batteries must remain installed to retain time settings.

■Disconnect newly-cloned TV from power for 5 seconds.

Cloning did not work

New Setup not present

Clone time disappeared

113

APPENDIX

GLOSSARY OF TERMS

75 OHM RF CABLE

The wire that comes from an off-air

antenna or cable service provider. The

end looks like a hex-shaped nut with a

wire sticking through the middle. It

screws onto the Antenna/Cable thread-

ed jack on the back of the TV.

300 TO 75 OHM ADAPTER

A small device that connects a

two-wire 300 ohm antenna to a 75

ohm RF jack. They are usually about an

inch long with two screws on one end

and a round opening with a wire sticking

out on the other end.

ANALOG TELEVISION

Standard television broadcasting format

in 4:3 picture aspect ratio.

A/V CABLES

Audio/Video cables. Three cables

bunched together—right audio (red),

left audio (white), and video (yellow).

A/V cables are used for stereo play-

back of videocassettes and other A/V

devices.

A/V DEVICE

Any device that produces video or

sound (VCR, DVD, cable box, or televi-

sion).

AMPLIFIER

An electronic device that amplifies

sound from a television, CD player, VCR,

DVD, or other Audio/Video device.

ANTENNA

The physical receiver of television signals

sent over the air. A large metal piece of

equipment does not always have to be

visible to be using an antenna.

CABLE

Cable service box. Refers to the

descrambler box cable subscribers use

to receive cable programming signals.

CABLE TELEVISION

Programming provided by a cable ser-

vice.

DIGITAL TELEVISION

Televisions signals that are transmitted

digitally.

DVI

Digital Video Interface

Accommodates analog and digital inter-

faces with a single connector.

COMPOSITE VIDEO

Typical video jack, uses one wire for

transporting three-color video signals.

COMPONENT VIDEO

Uses three wires for transporting three-

color video signals. Supports higher

quality video.

DELETED

Lets you remove channels from the list

that the end user can scroll through

using CH (Channel) Up/Down.

HDMI

High-definition multi-media interface.

HDTV

High-definition television. Refers to tele-

vision signals that have higher resolution

than ordinary analog TV signals.

HDSTB

High-definition set top box. Refers to a

tuner device that receives high-defini-

tion television signals which have higher

resolution than ordinary analog TV sig-

nals.

INPUT

Refers to the input jack that receives a

signal from a TV, VCR, DVD Player or

other Audio/Video device.

JACK

An input or output connector on the

back of a TV, VCR, DVD Player or

other Audio/Video device.

MONO SOUND

Mono (monaural) sound is one channel

of sound. On more than one speaker, all

the speakers play the same audio.

OUTPUT

Refers to the output jack that sends a

signal out of a VCR, DVD, or other A/V

device.

PHYSICAL CHANNEL NUMBER

The actual channel number. Analog

channels use the physical channel num-

ber and digital channels can use a virtual

channel number.

RGB (Red, Green, Blue)

Connection input or output port avail-

able for producing a video image using

three separate colors: Red, Green, and

Blue.

RS-232

Serial communication port through

which firmware is downloaded.

2ND AUDIO PROGRAMMING/SAP

Second Audio Programming (SAP) is

another, separate audio channel available

with some programming. Choosing SAP

often refers to listening to audio in

another language, such as Spanish or

French.

SIGNAL

Picture and sound traveling through a

cable, or over the air, to the TV.

STEREO SOUND

Stereo (Stereophonic) sound refers to

audio that’s divided into right and left

sides.

TUNER

Device that picks up the broadcast sig-

nal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER

A re-mapped channel number. Analog

channels use the actual channel number,

but digital channels use a virtual(or

fake) channel number.

XDS

Extended Data Service: Additional pro-

gram information included on the signal

provided at the discretion of the broad-

caster.

A list of definitions for some of the words found in this guide

APPENDIX

114

MAINTENANCE

■The specifications shown above may be changed without prior notice for quality improvement.

Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you can

enjoy your new TV.

Caution: Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a

little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

GG If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug

the power cord to protect against possible damage from lightning or power surges.

CAUTION

GGDo not use window/glass cleaner or anything with ammonia to clean the screen.

WARNING

Cleaning the Cabinet

■To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

■Please be sure not to use a wet cloth.

Extended Absence

MODEL

AC100-240V ~ 50/60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2-13, UHF 14-69, CATV 1-135, DTV 2-69, CADTV 1-135

75 ohm

32 ~ 104°F (0 ~40°C)

Less than 80%

-4 ~ 140°F (-20 ~60°C)

Less than 85%

Dimensions

(Width

x Height

x Depth)

Weight

Power requirement

Television System

Program Coverage

External Antenna Impedance

Environment

condition

With stand

Without stand

With stand

Without stand

Operating Temperature

Operating Humidity

Storage Temperature

Storage Humidity

42LG700H/710H

(42LG700H/710H-UA)

(42LG700H/710H-UB)

40.4 x 28.8 x 11.5 inches

1026.2 x 734.0 x 293.4 mm

40.4 x 27.0 x 4.4 inches

1026.2 x 687.9 x 111.8 mm

49.1 pounds / 22.3 kg

43.2 pounds / 19.6 kg

37LG700H/710H

(37LG700H/710H-UA)

(37LG700H/710H-UB)

36.1 x 26.9 x 11.5 inches

918.6 x 684.8 x 293.4 mm

36.1 x 24.9 x 3.4 inches

918.6 x 632.8 x 88 mm

41.6 pounds / 18.8 kg

35.2 pounds / 15.9 kg

32LG700H/710H

(32LG700H/710H-UA)

(32LG700H/710H-UB)

31.3 x 23.5 x 8.9 inches

797 x 597 x 227.3 mm

31.3 x 21.9 x 3.9 inches

797 x 558.6 x 100.5 mm

21.6 pounds / 9.82 kg

18.3 pounds / 8.34 kg

MPI card

(Width x Height x Depth)

3.1 x 0.9 x 6.3 inches

80.0(

0.6/-0.2) x less than 23.0(including pcb thickness) x less than 162.0(excluding cover thickness) mm

PRODUCT SPECIFICATIONS

3.7 x 1.1 inches

94.7(

0.5) x 28.3(

0.5) mm

Card Bracket Cover

(Width x Height )

Cable Card

APPENDIX

Remote Control Code

APPENDIX

116

Brand Codes Brand Codes Brand Codes

AIWA 034

AKAI 016 043 046 124

125 14 6

AMPRO 072

ANAM 031 033 103

AUDIO DYNAMICS

012 023 039 043

BROKSONIC 035 037 129

CANON 028 031 033

CAPEHART 108

CRAIG 003 040 135

CURTIS MATHES 031 033 041

DAEWOO 005 007 010 064

065 108 110 111

112 116 117 119

DAYTRON 108

DBX 012 023 039 043

DYNATECH 034 053

ELECTROHOME 059

EMERSON 006 017 025 027

029 031 034 035

036 037 046 101

129 131 138 153

FISHER 003 008 009 010

FUNAI 034

GE 031 033 063 072

107 109 14 4 147

GO VIDEO 132 136

HARMAN KARDON 012 045

HITACHI 004 018 026 034

043 063 137 150

INSTANTREPLAY 031 033

JCL 031 033

JCPENNY 012 013 015 033

040 066 101

JENSEN 043

JVC 012 031 033 043

048 050 055 060

130 150 152

KENWOOD 014 034 039 043

047 048

LG (GOLDSTAR) 001 012 013 020

101 10 6 114 123

LLOYD 034

LXI 003 009 013 014

017 034 101 106

MAGIN 040

MAGNAVOX 031 033 034 041

067 068

MARANTZ 012 031 033 067

069

MARTA 101

MATSUI 027 030

MEI 031 033

MEMOREX 003 010 014 031

033 034 053 072

101 102 134 139

MGA 045 046 059

MINOLTA 013 020

MITSUBISHI 013 020 045 046

049 051 059 061

151

MTC 034 040

MULTITECH 024 034

NEC 012 023 039 043

048

NORDMENDE 043

OPTONICA 053 054

PANASONIC 066 070 074 083

133 14 0 145

PENTAX 013 020 031 033

063

PHILCO 031 034 067

PHILIPS 031 033 034 054

067 071 101

PILOT 101

PIONEER 013 021 048

PORTLAND 108

PULSAR 072

QUARTZ 011 014

QUASAR 033 066 075 145

RCA 013 020 033 034

040 041 062 063

107 109 140 144

145 147

REALISTIC 003 008 010 014

031 033 034 040

053 054 101

RICO 058

RUNCO 148

SALORA 014

SAMSUNG 032 040 102 104

105 107 109 112

113 115 120 122

125

SANSUI 022 043 048 135

SANYO 003 007 010 014

102 134

SCOTT 017 037 112 129

131

SEARS 003 008 009 010

013 014 017 020

031 042 073 081

101

SHARP 031 054 149

SHINTOM 024

SONY 003 009 031 052

056 057 058 076

077 078 149

SOUNDESIGN 034

STS 013

SYLVANIA 031 033 034 059

067

SYMPHONIC 034

TANDY 010 034

TATUNG 039 043

TEAC 034 039 043

TECHNICS 031 033 070

TEKNIKA 019 031 033 034

101

THOMAS 034

TMK 006

TOSHIBA 008 013 042 047

059 082 112 131

TOTEVISION 040 101

UNITECH 040

VECTOR RESEARCH

012

VICTOR 048

VIDEO CONCEPTS

012 034 046

VIDEOSONIC 040

WARDS 003 013 017 024

031 033 034 040

053 054 131

YAMAHA 012 034 039 043

ZENITH 034 048 056

058 072 080 101

VCR

APPENDIX

117

Brand Codes Brand Codes Brand Codes

HDSTB

ALPHASTAR DSR 123

AMPLICA 050

ASTRO PHILIPS(ML) 159

ASTRO THOMPSON(ML) 160

ASTRO NOKIA(ML) 161

BIRDVIEW 051 126 129

CHANNEL MASTER

013 014 015 018

036 055

CHAPARRAL 008 009 012 077

CITOH 054

CURTIS MATHES 050 145

DRAKE 005 006 007 010

011 052 112 116

141

DX ANTENNA 024 046 056 076

ECHOSTAR 038 040 057 058

093 094 095 096

097 098 099 100

122

ELECTRO HOME 089

EUROPLUS 114

FUJITSU 017 021 022 027

133 134

GENERAL INSTRUMENT

003 004 016 029

031 059 101

HITACHI 139 140

HOUSTON TRACKER

033 037 039 051

057 104

HUGHES 068

HUMAX(SL) 158

JANIEL 060 147

JERROLD 061

KATHREIN 108

LEGEND 057

LG 001

LUTRON 132

LUXOR 062 144

MACOM 010 059 063 064

065

MEMOREX 057

NEXTWAVE 028 124 125

NORSAT 069 070

PACE SKY SATELLITE

143

PANASONIC 060 142

PANSAT 121

PERSONAL CABLE 117

PHILIPS 071

PICO 105

PRESIDENT 019 102

PRIMESTAR 030 110 111

PROSAT 072

PSI(TH) 157

RCA 066 106

REALISTIC 043 074

SAMSUNG 123

SATELLITE SERVICE CO

028 035 047 057

085

SCIENTIFIC ATLANTA

032 138

SKY LIFE 150

SONY 103

STARCAST 041

SUPER GUIDE 020 124 125

SAMART(TH) 156

TEECOM 023 026 075 087

088 090 107 130

137

TOSHIBA 002 127

TRUE VISION(TH) 155

UNIDEN 016 025 042 043

044 045 048 049

078 079 080 086

101 135 136

UBC(TH) 153

UBC/SAMART(TH) 154

VIEWSTAR 115

VTC(VN) 162

WINEGARD 128 146

ZENITH 081 082 083 084

091 120

DVD

Brand Codes Brand Codes Brand Codes

APEX DIGITAL 022

DENON 020 014

GE 005 006

HARMAN KARDON 027

JVC 012

LG 001 010 016 025

MAGNAVOX 013

MARANTZ 024

MITSUBISHI 002

NAD 023

ONKYO 008 017

PANASONIC 003 009

PHILIPS 013

PIONEER 004 026

PROCEED 021

PROSCAN 005 006

RCA 005 006

SAMSUNG 011 015

SONY 007

THOMPSON 005 006

TOSHIBA 019 008

YAMAHA 009 018

ZENITH 010 016 025

APPENDIX

119

Code Function Note

(Hexa) Code Function Note

(Hexa)

D6 TV Discrete IR Code

(TV Input Selection)

5A AV1

Discrete IR Code

(AV1 Input Selection)

D0 AV2 Discrete IR Code

(AV2 Input Selection)

BF COMPONENT

Discrete IR Code

(

COMPONENT

Input Selection)

D5 RGB-PC

Discrete IR Code

(

RGB

Input Selection)

CE HDMI1

Discrete IR Code

(

HDMI1

Input Selection)

CC HDMI2 Discrete IR Code

(HDMI2 Input Selection)

76 Ratio 4:3

Discrete IR Code

(

Only 4:3 Mode

)

77 Ratio 16:9

Discrete IR Code

(

Only 16:9 Mode

)

AF Ratio Zoom

Discrete IR Code

(

Only Zoom1 Mode

)

C4 POWER ON

Discrete IR Code

(

Only Power On

)

C5 POWER OFF

Discrete IR Code

(

Only Power Off)

08 POWER

Remote control Button (Power On/Off)

0F TV

Remote control Button

0B INPUT Remote control Button

0A SAP Remote control Button

79 FF RATIO Remote control Button

AB GUIDE Remote control Button

OC PORTAL Remote control Button

AA INFO Remote control Button

10-19 Number Key 0-9 Remote control Button

4C - (Dash) Remote control Button

1A FLASHBK Remote control Button

02 VOL + Remote control Button

03 VOL - Remote control Button

00 CH Remote control Button

01 CH Remote control Button

0E GG TIMER Remote control Button

39 CC Remote control Button

09 MUTE Remote control Button

43 MENU Remote control Button

5B RETURN Remote control Button

40 Remote control Button

41 Remote control Button

07 Remote control Button

06 Remote control Button

44 ENTER Remote control Button

60 PIP Remote control Button

71 PIP CH + Remote control Button

72 PIP CH- Remote control Button

63 PIP SWAP Remote control Button

61 PIP INPUT Remote control Button

C1 A Stop Remote control Button

C0 G Play Remote control Button

ll ll

Pause Remote control Button

C3 Ô(Record) Remote control Button

APPENDIX

OPEN SOURCE LICENSE

APPENDIX

120

Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of

this license document, but changing it is not allowed.

Preamble

The licenses for most software are designed to take away your

freedom to share and change it. By contrast, the GNU General

Public License is intended to guarantee your freedom to share

and change free software - to make sure the software is free for

all its users. This General Public License applies to most of the

Free Software Foundation's software and to any other program

whose authors commit to using it. (Some other free software

foundation software is covered by the GNU Lesser General Public

License instead.) You can apply it to your programs, too.

When we speak of free software, we are referring to freedom, not

price. Our General Public Licenses are designed to make sure that

you have the freedom to distribute copies of free software (and

charge for this service if you wish), that you receive source code

or can get it if you want it, that you can change the software or

use pieces of it in new free programs; and that you know you can

do these things.

To protect your rights, we need to make restrictions that forbid

anyone to deny you these rights or to ask you to surrender the

rights. These restrictions translate to certain responsibilities for

you if you distribute copies of the software, or if you modify it.

For example, if you distribute copies of such a program, whether

gratis or for a fee, you must give the recipients all the rights that

you have. You must make sure that they, too, receive or can get

the source code. And you must show them these terms so they

know their rights.

We protect your rights with two steps: (1) copyright the soft-

ware, and (2) offer you this license which gives you legal permis-

sion to copy, distribute and/or modify the software.

Also, for each author's protection and ours, we want to make cer-

tain that everyone understands that there is no warranty for this

free software. If the software is modified by someone else and

passed on, we want its recipients to know that what they have is

not the original, so that any problems introduced by others will

not reflect on the original authors' reputations.

Finally, any free program is threatened constantly by software

patents. We wish to avoid the danger that redistributors of a free

program will individually obtain patent licenses, in effect making

the program proprietary. To prevent this, we have made it clear

that any patent must be licensed for everyone's free use or not

licensed at all.

The precise terms and conditions for copying, distribution and

modification follow.

GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION

AND MODIFICATION

0. This license applies to any program or other work which con-

tains a notice placed by the copyright holder saying it may be

distributed under the terms of this General Public License. The

"Program", below, refers to any such program or work, and a

"work based on the Program" means either the Program or any

derivative work under copyright law: that is to say, a work con-

taining the Program or a portion of it, either verbatim or with

modifications and/or translated into another language.

(Hereinafter, translation is included without limitation in the

term "modification".) Each licensee is addressed as "you".

Activities other than copying, distribution and modification

are not covered by this license; they are outside its scope.

The act of running the Program is not restricted, and the out-

put from the program is covered only if its contents constitute

a work based on the program (independent of having been

made by running the program). Whether that is true depends

on what the program does.

1. You may copy and distribute verbatim copies of the program's

source code as you receive it, in any medium, provided that

you conspicuously and appropriately publish on each copy an

appropriate copyright notice and disclaimer of warranty; keep

intact all the notices that refer to this license and to the

absence of any warranty; and give any other recipients of the

program a copy of this license along with the Program.

You may charge a fee for the physical act of transferring a

copy, and you may at your option offer warranty protection in

exchange for a fee.

2. You may modify your copy or copies of the program or any

portion of it, thus forming a work based on the Program, and

copy and distribute such modifications or work under the

terms of section 1 above, provided that you also meet all of

these conditions:

a) You must cause the modified files to carry prominent

notices stating that you changed the files and the date of

any change.

GNU GENERAL PUBLIC LICENSE

Version 2, June 1991

APPENDIX

121

b) You must cause any work that you distribute or publish,

that in whole or in part contains or is derived from the

Program or any part there of, to be licensed as a whole at

no charge to all third parties under the terms of this

license.

c) If the modified program normally reads commands interac-

tively when run, you must cause it, when started running

for such interactive use in the most ordinary way, to print

or display an announcement including an appropriate

else, saying that you provide a warranty) and that users

may redistribute the program under these conditions, and

telling the user how to view a copy of this license.

(Exception: if the Program itself is interactive but does not

normally print such an announcement, your work based on

the Program is not required to print an announcement.)

These requirements apply to the modified work as a whole. If

identifiable sections of that work are not derived from the

Program, and can be reasonably considered independent and

separate works in themselves, then this license, and its terms,

do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as

part of a whole which is a work based on the Program, the dis-

tribution of the whole must be on the terms of this license,

whose permissions for other licensees extend to the entire

whole, and thus to each and every part regardless of who

wrote it.

Thus, it is not the intent of this section to claim rights or con-

test your rights to work written entirely by you; rather, the

intent is to exercise the right to control the distribution of

derivative or collective works based on the program.

In addition, mere aggregation of another work not based on

the program with the Program (or with a work based on the

program) on a volume of a storage or distribution medium

does not bring the other work under the scope of this license.

3. You may copy and distribute the program (or a work based on

it, under section 2) in object code or executable form under

the terms of sections 1 and 2 above provided that you also

do one of the following:

a) Accompany it with the complete corresponding machine-

readable source code, which must be distributed under the

terms of sections 1 and 2 above on a medium customarily

used for software interchange; or,

b) Accompany it with a written offer, valid for at least three

years, to give any third party, for a charge no more than

your cost of physically performing source distribution, a

complete machine-readable copy of the corresponding

source code, to be distributed under the terms of sections

1 and 2 above on a medium customarily used for software

interchange; or,

c) Accompany it with the information you received as to the

offer to distribute corresponding source code. (This alter-

native is allowed only for noncommercial distribution and

only if you received the program in object code or exe-

cutable form with such an offer, in accord with Subsection

b above.)

The source code for a work means the preferred form of the

work for making modifications to it. For an executable work,

complete source code means all the source code for all mod-

ules it contains, plus any associated interface definition files,

plus the scripts used to control compilation and installation

of the executable. However, as a special exception, the source

code distributed need not include anything that is normally

distributed (in either source or binary form) with the major

components (compiler, kernel, and so on) of the operating

system on which the executable runs, unless that component

itself accompanies the executable.

If distribution of executable or object code is made by offer-

ing access to copy from a designated place, then offering

equivalent access to copy the source code from the same

place counts as distribution of the source code, even though

third parties are not compelled to copy the source along with

the object code.

4. You may not copy, modify, sublicense, or distribute the Program

except as expressly provided under this license. Any attempt

otherwise to copy, modify, sublicense or distribute the

Program is void, and will automatically terminate your rights

under this license. However, parties who have received copies,

or rights, from you under this license will not have their licens-

es terminated so long as such parties remain in full compli-

ance.

5. You are not required to accept this license, since you have not

signed it. However, nothing else grants you permission to

modify or distribute the Program or its derivative works.

These actions are prohibited by law if you do not accept this

license. Therefore, by modifying or distributing the program

(or any work based on the program), you indicate your accep-

tance of this license to do so, and all its terms and conditions

for copying, distributing or modifying the program or works

based on it.

6. Each time you redistribute the program (or any work based on

the Program), the recipient automatically receives a license

from the original licensor to copy, distribute or modify the

Program subject to these terms and conditions. You may not

impose any further restrictions on the recipients' exercise of

the rights granted herein. You are not responsible for enforc-

ing compliance by third parties to this license.

APPENDIX

122

7. If, as a consequence of a court judgment or allegation of

patent infringement or for any other reason (not limited to

patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the con-

ditions of this license, they do not excuse you from the con-

ditions of this license. If you cannot distribute so as to satis-

fy simultaneously your obligations under this license and any

other pertinent obligations, then as a consequence you may

not distribute the program at all. For example, if a patent

license would not permit royalty-free redistribution of the

program by all those who receive copies directly or indirectly

through you, then the only way you could satisfy both it and

this license would be to refrain entirely from distribution of

the program.

If any portion of this section is held invalid or unenforceable

under any particular circumstance, the balance of the section

is intended to apply and the section as a whole is intended to

apply in other circumstances.

It is not the purpose of this section to induce you to infringe

any patents or other property right claims or to contest valid-

ity of any such claims; this section has the sole purpose of

protecting the integrity of the free software distribution sys-

tem, which is implemented by public license practices. Many

people have made generous contributions to the wide range

of software distributed through that system in reliance on

consistent application of that system; it is up to the

author/donor to decide if he or she is willing to distribute

software through any other system and a licensee cannot

impose that choice.

This section is intended to make thoroughly clear what is

believed to be a consequence of the rest of this license.

8. If the distribution and/or use of the program is restricted in

certain countries either by patents or by copyrighted inter-

faces, the original copyright holder who places the program

under this license may add an explicit geographical distribution

limitation excluding those countries, so that distribution is

permitted only in or among countries not thus excluded. In

such case, this license incorporates the limitation as if written

in the body of this license.

9. The Free Software Foundation may publish revised and/or

new versions of the General Public License from time to time.

Such new versions will be similar in spirit to the present ver-

sion, but may differ in detail to address new problems or con-

cerns.

Each version is given a distinguishing version number. If the

program specifies a version number of this license which

applies to it and "any later version", you have the option of

following the terms and conditions either of that version or of

any later version published by the Free Software Foundation.

If the program does not specify a version number of this

license, you may choose any version ever published by the

Free Software Foundation.

10.If you wish to incorporate parts of the program into other free

programs whose distribution conditions are different, write to

the author to ask for permission. For software which is copy-

righted by the Free Software Foundation, write to the Free

Software Foundation; we sometimes make exceptions for this.

Our decision will be guided by the two goals of preserving the

free status of all derivatives of our free software and of pro-

moting the sharing and reuse of software generally.

NO WARRANTY

11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,

THERE IS NO WARRANTY FOR THE PROGRAM, TO THE

EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-

ERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS

IS" WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE

RISK AS TO THE QUALITY AND PERFORMANCE OF THE

PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE

DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

12.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR

AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,

OR ANY OTHER PARTY WHO MAY MODIFY AND/OR

REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE

LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE USE OR INABILITY TO USE THE PRO-

GRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA

OR DATA BEING RENDERED INACCURATE OR LOSSES SUS-

TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE

PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS),

EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

APPENDIX

123

END OF TERMS AND CONDITIONS

How to apply these terms to your new programs

If you develop a new program, and you want it to be of the great-

est possible use to the public, the best way to achieve this is to

make it free software which everyone can redistribute and change

under these terms.

To do so, attach the following notices to the program. It is safest

to attach them to the start of each source file to most effective-

ly convey the exclusion of warranty; and each file should have at

least the "copyright" line and a pointer to where the full notice is

found.

one line to give the program's name and a brief idea of what it

does.

This program is free software; you can redistribute it and/or

modify it under the terms of the GNU General Public License as

published by the Free Software Foundation; either version 2 of

the license, or (at your option) any later version.

This program is distributed in the hope that it will be useful, but

WITHOUT ANY WARRANTY; without even the implied warranty

of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-

POSE. See the GNU General Public License for more details.

You should have received a copy of the GNU General Public

License along with this program; if not, write to the Free Software

Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA

02110-1301 USA.

Also add information on how to contact you by electronic and

paper mail.

If the program is interactive, make it output a short notice like

this when it starts in an interactive mode:

Gnomovision version 69, Copyright (C) year name of author

Gnomovision comes with ABSOLUTELY NO WARRANTY; for

details type ‘show w’. This is free software, and you are welcome

to redistribute it under certain conditions; type ‘show c’ for

details.

The hypothetical commands ‘show w’ and ‘show c’ should show

the appropriate parts of the General Public License. Of course,

the commands you use may be called something other than

‘show w’ and ‘show c’; they could even be mouse-clicks or menu

items-whatever suits your program.

You should also get your employer (if you work as a programmer)

or your school, if any, to sign a “copyright disclaimer” for the pro-

gram, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the pro-

gram ‘Gnomovision’ (which makes passes at compilers) written by

James Hacker.

signature of Ty Coon, 1 April 1989

Ty Coon, President of Vice

This General Public License does not permit incorporating your

program into proprietary programs. If your program is a subrou-

tine library, you may consider it more useful to permit linking pro-

prietary applications with the library. If this is what you want to

do, use the GNU Lesser General Public License instead of this

license.

APPENDIX

124

Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA

Everyone is permitted to copy and distribute verbatim copies of

this license document, but changing it is not allowed.

[This is the first released version of the Lesser GPL. It also

counts as the successor of the GNU Library Public License, ver-

sion 2, hence the version number 2.1.]

Preamble

The licenses for most software are designed to take away your

freedom to share and change it. By contrast, the GNU General

Public Licenses are intended to guarantee your freedom to share

and change free software - to make sure the software is free for

all its users.

This license, the Lesser General Public License, applies to some

specially designated software packages - typically libraries - of

the Free Software Foundation and other authors who decide to

use it. You can use it too, but we suggest you first think careful-

ly about whether this license or the ordinary General Public

License is the better strategy to use in any particular case, based

on the explanations below.

When we speak of free software, we are referring to freedom of

use, not price. Our General Public Licenses are designed to make

sure that you have the freedom to distribute copies of free soft-

ware (and charge for this service if you wish); that you receive

source code or can get it if you want it; that you can change the

software and use pieces of it in new free programs; and that you

are informed that you can do these things.

To protect your rights, we need to make restrictions that forbid

distributors to deny you these rights or to ask you to surrender

these rights. These restrictions translate to certain responsibilities

for you if you distribute copies of the library or if you modify it.

For example, if you distribute copies of the library, whether gratis

or for a fee, you must give the recipients all the rights that we

gave you. You must make sure that they, too, receive or can get

the source code. If you link other code with the library, you must

provide complete object files to the recipients, so that they can

relink them with the library after making changes to the library

and recompiling it. And you must show them these terms so they

know their rights.

We protect your rights with a two-step method: (1) we copyright

the library, and (2) we offer you this license, which gives you legal

permission to copy, distribute and/or modify the library.

To protect each distributor, we want to make it very clear that

there is no warranty for the free library. Also, if the library is mod-

ified by someone else and passed on, the recipients should know

that what they have is not the original version, so that the origi-

nal author's reputation will not be affected by problems that

might be introduced by others.

Finally, software patents pose a constant threat to the existence

of any free program. We wish to make sure that a company can-

not effectively restrict the users of a free program by obtaining a

restrictive license from a patent holder. Therefore, we insist that

any patent license obtained for a version of the library must be

consistent with the full freedom of use specified in this license.

Most GNU software, including some libraries, is covered by the

ordinary GNU General Public License. This license, the GNU

Lesser General Public License, applies to certain designated

libraries, and is quite different from the ordinary General Public

License. We use this license for certain libraries in order to per-

mit linking those libraries into non-free programs.

When a program is linked with a library, whether statically or

using a shared library, the combination of the two is legally

speaking a combined work, a derivative of the original library. The

ordinary General Public License therefore permits such linking

only if the entire combination fits its criteria of freedom. The

Lesser General Public License permits more lax criteria for linking

other code with the library.

We call this license the "Lesser" General Public License because

it does Less to protect the user's freedom than the ordinary

General Public License. It also provides other free software devel-

opers Less of an advantage over competing non-free programs.

These disadvantages are the reason we use the ordinary General

Public License for many libraries. However, the Lesser license pro-

vides advantages in certain special circumstances.

For example, on rare occasions, there may be a special need to

encourage the widest possible use of a certain library, so that it

becomes a de-facto standard. To achieve this, non-free programs

must be allowed to use the library. A more frequent case is that

a free library does the same job as widely used non-free libraries.

In this case, there is little to gain by limiting the free library to free

software only, so we use the Lesser General Public License.

In other cases, permission to use a particular library in non-free

programs enables a greater number of people to use a large body

of free software. For example, permission to use the GNU C

Library in non-free programs enables many more people to use

the whole GNU operating system, as well as its variant, the

GNU/Linux operating system.

GNU LESSER GENERAL PUBLIC LICENSE

Version 2.1, February 1999

APPENDIX

125

Although the Lesser General Public License is Less protective of

the users' freedom, it does ensure that the user of a program that

is linked with the Library has the freedom and the wherewithal to

run that program using a modified version of the Library.

The precise terms and conditions for copying, distribution and

modification follow. Pay close attention to the difference between

a "work based on the library" and a "work that uses the library".

The former contains code derived from the library, whereas the

latter must be combined with the library in order to run.

GNU LESSER GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION

AND MODIFICATION

0. This license agreement applies to any software library or other

program which contains a notice placed by the copyright hold-

er or other authorized party saying it may be distributed

under the terms of this Lesser General Public License (also

called “this license”). Each license is addressed as "you".

A “library” means a collection of software functions and/or

data prepared so as to be conveniently linked with application

programs (which use some of those functions and data) to

form executables.

The “Library”, below, refers to any such software library or work

which has been distributed under these terms. A “work based

on the Library” means either the Library or any derivative work

under copyright law: that is to say, a work containing the

library or a portion of it, either verbatim or with modifications

and/or translated straightforwardly into another language.

(Hereinafter, translation is included without limitation in the

term “modification”.)

“Source code” for a work means the preferred form of the

work for making modifications to it. For a library, complete

source code means all the source code for all modules it con-

tains, plus any associated interface definition files, plus the

scripts used to control compilation and installation of the

library.

Activities other than copying, distribution and modification

are not covered by this license; they are outside its scope.

The act of running a program using the Library is not restrict-

ed, and output from such a program is covered only if its con-

tents constitute a work based on the library (independent of

the use of the Library in a tool for writing it). Whether that is

true depends on what the library does and what the program

that uses the library does.

1. You may copy and distribute verbatim copies of the library's

complete source code as you receive it, in any medium, pro-

vided that you conspicuously and appropriately publish on

each copy an appropriate copyright notice and disclaimer of

warranty; keep intact all the notices that refer to this license

and to the absence of any warranty; and distribute a copy of

this license along with the Library.

You may charge a fee for the physical act of transferring a

copy, and you may at your option offer warranty protection in

exchange for a fee.

2. You may modify your copy or copies of the Library or any

portion of it, thus forming a work based on the Library, and

copy and distribute such modifications or work under the

terms of section 1 above, provided that you also meet all of

these conditions:

a) The modified work must itself be a software library.

b) You must cause the files modified to carry prominent

notices stating that you changed the files and the date of

any change.

c) You must cause the whole of the work to be licensed at no

charge to all third parties under the terms of this license.

d) If a facility in the modified Library refers to a function or a

table of data to be supplied by an application program that

uses the facility, other than as an argument passed when

the facility is invoked, then you must make a good faith

effort to ensure that, in the event an application does not

supply such function or table, the facility still operates, and

performs whatever part of its purpose remains meaningful.

(For example, a function in a library to compute square roots

has a purpose that is entirely well-defined independent of the

application. Therefore, Subsection 2d requires that any appli-

cation-supplied function or table used by this function must be

optional: if the application does not supply it, the square root

function must still compute square roots.)

These requirements apply to the modified work as a whole. If

identifiable sections of that work are not derived from the

library, and can be reasonably considered independent and

separate works in themselves, then this license, and its terms,

do not apply to those sections when you distribute them as

separate works. But when you distribute the same sections as

part of a whole which is a work based on the library, the dis-

tribution of the whole must be on the terms of this license,

whose permissions for other licenses extend to the entire

whole, and thus to each and every part regardless of who

wrote it.

Thus, it is not the intent of this section to claim rights or con-

test your rights to work written entirely by you; rather, the

intent is to exercise the right to control the distribution of

derivative or collective works based on the library.

In addition, mere aggregation of another work not based on

the library with the library (or with a work based on the

library) on a volume of a storage or distribution medium does

not bring the other work under the scope of this license.

APPENDIX

126

3. You may opt to apply the terms of the ordinary GNU General

Public License instead of this License to a given copy of the

Library. To do this, you must alter all the notices that refer to

this License, so that they refer to the ordinary GNU General

Public License, version 2, instead of to this License. (If a newer

version than version 2 of the ordinary GNU General Public

License has appeared, then you can specify that version

instead if you wish.) Do not make any other change in these

notices.

Once this change is made in a given copy, it is irreversible for

that copy, so the ordinary GNU General Public License applies

to all subsequent copies and derivative works made from that

copy.

This option is useful when you wish to copy part of the code

of the library into a program that is not a library.

4. You may copy and distribute the library (or a portion or deriv-

ative of it, under Section 2) in object code or executable form

under the terms of Sections 1 and 2 above provided that you

accompany it with the complete corresponding machine-

readable source code, which must be distributed under the

terms of sections 1 and 2 above on a medium customarily

used for software interchange.

If distribution of object code is made by offering access to

copy from a designated place, then offering equivalent access

to copy the source code from the same place satisfies the

requirement to distribute the source code, even though third

parties are not compelled to copy the source along with the

object code.

5. A program that contains no derivative of any portion of the

Library, but is designed to work with the Library by being

compiled or linked with it, is called a “work that uses the

Library”. Such a work, in isolation, is not a derivative work of

the Library, and therefore falls outside the scope of this

license.

However, linking a “work that uses the library” with the Library

creates an executable that is a derivative of the Library

(because it contains portions of the library), rather than a

“work that uses the library”. The executable is therefore cov-

ered by this license. Section 6 states terms for distribution of

such executable.

When a “work that uses the library” uses material from a head-

er file that is part of the library, the object code for the work

may be a derivative work of the library even though the source

code is not.

Whether this is true is especially significant if the work can be

linked without the library, or if the work is itself a library. The

threshold for this to be true is not precisely defined by law.

If such an object file uses only numerical parameters, data

structure layouts and accessories, and small macros and small

inline functions (ten lines or less in length), then the use of

the object file is unrestricted, regardless of whether it is legal-

ly a derivative work. (Executable containing this object code

plus portions of the library will still fall under Section 6.)

Otherwise, if the work is a derivative of the library, you may

distribute the object code for the work under the terms of

Section 6. Any executable containing that work also fall under

Section 6, whether or not they are linked directly with the

library itself.

6. As an exception to the sections above, you may also combine

or link a "work that uses the library" with the library to pro-

duce a work containing portions of the library, and distribute

that work under terms of your choice, provided that the terms

permit modification of the work for the customer's own use

and reverse engineering for debugging such modifications.

You must give prominent notice with each copy of the work

that the library is used in it and that the Library and its use

are covered by this license. You must supply a copy of this

license. If the work during execution displays copyright

notices, you must include the copyright notice for the library

among them, as well as a reference directing the user to the

copy of this license. Also, you must do one of these things:

a) Accompany the work with the complete corresponding

machine-readable source code for the library including

whatever changes were used in the work (which must be

distributed under Sections 1 and 2 above); and, if the work

is an executable linked with the Library, with the complete

machine-readable “work that uses the Library”, as object

code and/or source code, so that the user can modify the

library and then relink to produce a modified executable

containing the modified library. (It is understood that the

user who changes the contents of definitions files in the

library will not necessarily be able to recompile the appli-

cation to use the modified definitions.)

b) Use a suitable shared library mechanism for linking with the

library. A suitable mechanism is one that (1) uses at run time

a copy of the library already present on the user’s computer

system, rather than copying library functions into the exe-

cutable, and (2) will operate properly with a modified version

of the library, if the user installs one, as long as the modified

version is interface-compatible with the version that the

work was made with.

c) Accompany the work with a written offer, valid for at least

three years, to give the same user the materials specified in

Subsection 6, above, for a charge no more than the cost of

performing this distribution.

d) If distribution of the work is made by offering access to

copy from a designated place, offer equivalent access to

copy the above specified materials from the same place.

e) Verify that the user has already received a copy of these

materials or that you have already sent this user a copy.

APPENDIX

127

For an executable, the required form of the "work that uses

the library" must include any data and utility programs need-

ed for reproducing the executable from it. However, as a spe-

cial exception, the materials to be distributed need not

include anything that is normally distributed (in either source

or binary form) with the major components (compiler, kernel,

and so on) of the operating system on which the executable

runs, unless that component itself accompanies the exe-

cutable.

It may happen that this requirement contradicts the license

restrictions of other proprietary libraries that do not normal-

ly accompany the operating system. Such a contradiction

means you cannot use both them and the library together in

an executable that you distribute.

7. You may place library facilities that are a work based on the

library side-by-side in a single library together with other

library facilities not covered by this license, and distribute

such a combined library, provided that the separate distribu-

tion of the work based on the Library and of the other library

facilities is otherwise permitted, and provided that you do

these two things:

a) Accompany the combined library with a copy of the same

work based on the Library, uncombined with any other

library facilities. This must be distributed under the terms

of the sections above.

b) Give prominent notice with the combined library of the

fact that part of it is a work based on the library, and

explaining where to find the accompanying uncombined

form of the same work.

8. You may not copy, modify, sublicense, link with, or distribute

the library except as expressly provided under this license.

Any attempt otherwise to copy, modify, sublicense, link with,

or distribute the library is void, and will automatically termi-

nate your rights under this license. However, parties who have

received copies, or rights, from you under this license will not

have their licenses terminated so long as such parties remain

in full compliance.

9. You are not required to accept this license, since you have not

signed it. However, nothing else grants you permission to mod-

ify or distribute the library or its derivative works. These

actions are prohibited by law if you do not accept this license.

Therefore, by modifying or distributing the library (or any work

based on the library), you indicate your acceptance of this

license to do so, and all its terms and conditions for copying,

distributing or modifying the library or works based on it.

10.Each time you redistribute the library (or any work based on

the Library), the recipient automatically receives a license

from the original licensor to copy, distribute, link with or mod-

ify the library subject to these terms and conditions. You may

not impose any further restrictions on the recipients' exercise

of the rights granted herein.

You are not responsible for enforcing compliance by third

parties with this license.

11. If, as a consequence of a court judgment or allegation of

patent infringement or for any other reason (not limited to

patent issues), conditions are imposed on you (whether by

court order, agreement or otherwise) that contradict the con-

ditions of this license, they do not excuse you from the con-

ditions of this license. If you cannot distribute so as to satis-

fy simultaneously your obligations under this license and any

other pertinent obligations, then as a consequence you may

not distribute the library at all. For example, if a patent license

would not permit royalty-free redistribution of the library by

all those who receive copies directly or indirectly through

you, then the only way you could satisfy both it and this

license would be to refrain entirely from distribution of the

library.

If any portion of this section is held invalid or unenforceable

under any particular circumstance, the balance of the section

is intended to apply, and the section as a whole is intended to

apply in other circumstances.

It is not the purpose of this section to induce you to infringe

any patents or other property right claims or to contest valid-

ity of any such claims; this section has the sole purpose of

protecting the integrity of the free software distribution sys-

tem which is implemented by public license practices. Many

people have made generous contributions to the wide range

of software distributed through that system in reliance on

consistent application of that system; it is up to the

author/donor to decide if he or she is willing to distribute

software through any other system and a license cannot

impose that choice.

This section is intended to make thoroughly clear what is

believed to be a consequence of the rest of this license.

12.If the distribution and/or use of the library is restricted in cer-

tain countries either by patents or by copyrighted interfaces,

the original copyright holder who places the library under this

license may add an explicit geographical distribution limitation

excluding those countries, so that distribution is permitted

only in or among countries not thus excluded. In such case,

this license incorporates the limitation as if written in the body

of this license.

13.The Free Software Foundation may publish revised and/or

new versions of the Lesser General Public License from time to

time. Such new versions will be similar in spirit to the present

version, but may differ in detail to address new problems or

concerns.

Each version is given a distinguishing version number. If the

library specifies a version number of this license which applies

to it and “any later version”, you have the option of following

the terms and conditions either of that version or of any later

version published by the Free Software Foundation.

APPENDIX

128

If the library does not specify a license version number, you

may choose any version ever published by the Free Software

Foundation.

14.If you wish to incorporate parts of the library into other free

programs whose distribution conditions are incompatible with

these, write to the author to ask for permission. For software

which is copyrighted by the Free Software Foundation, write

to the Free Software Foundation; we sometimes make excep-

tions for this. Our decision will be guided by the two goals of

preserving the free status of all derivatives of our free software

and of promoting the sharing and reuse of software generally.

NO WARRANTY

15.BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,

THERE IS NO WARRANTY FOR THE LIBRARY, TO THE

EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN

OTHERWISE STATED IN WRITING THE COPYRIGHT HOLD-

ERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS

IS" WITHOUT WARRANTY OF ANY KIND, EITHER

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED

TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE

RISK AS TO THE QUALITY AND PERFORMANCE OF THE

LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE

DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY

SERVICING, REPAIR OR CORRECTION.

16.IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR

AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,

OR ANY OTHER PARTY WHO MAY MODIFY AND/OR

REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE

LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL,

SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

ARISING OUT OF THE USE OR INABILITY TO USE THE

LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA

OR DATA BEING RENDERED INACCURATE OR LOSSES SUS-

TAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE

LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE),

EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN

ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS

How to apply these terms to your new libraries

If you develop a new library, and you want it to be of the great-

est possible use to the public, we recommend making it free soft-

ware that everyone can redistribute and change. You can do so

by permitting redistribution under these terms (or, alternatively,

under the terms of the ordinary General Public License).

To apply these terms, attach the following notices to the library.

It is safest to attach them to the start of each source file to most

effectively convey the exclusion of warranty; and each file should

have at least the “copyright” line and a pointer to where the full

notice is found.

one line to give the library's name and a brief idea of what it does.

This library is free software; you can redistribute it and/or modify

it under the terms of the GNU Lesser General Public License as

published by the Free Software Foundation; either version 2.1 of

the license, or (at your option) any later version.

This library is distributed in the hope that it will be useful, but

WITHOUT ANY WARRANTY; without even the implied warranty

of MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-

POSE. See the GNU Lesser General Public License for more

details.

You should have received a copy of the GNU Lesser General

Public License along with this library; if not, write to the Free

Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,

MA 02110-1301 USA

Also add information on how to contact you by electronic and

paper mail.

You should also get your employer (if you work as a programmer)

or your school, if any, to sign a “copyright disclaimer” for the

library, if necessary. Here is a sample; alter the names:

Yoyodyne, Inc., hereby disclaims all copyright interest in the

library ‘Frob’ (a library for tweaking knobs) written by James

Random Hacker.

signature of Ty Coon, 1 April 1990

Ty Coon, President of Vice

APPENDIX

129

1.Definitions.

1.0.1. “Commercial use” means distribution or otherwise making

the covered code available to a third party.

1.1. “Contributor” means each entity that creates or con-

tributes to the creation of modifications.

1.2. “Contributor version” means the combination of the orig-

inal code, prior modifications used by a contributor, and

the modifications made by that particular contributor.

1.3. “Covered code” means the original code or modifications

or the combination of the original code and modifications,

in each case including portions thereof.

1.4. “Electronic distribution mechanism” means a mechanism

generally accepted in the software development communi-

ty for the electronic transfer of data.

1.5. “Executable” means covered code in any form other than

source code.

1.6. “Initial developer” means the individual or entity identified

as the initial Developer in the Source Code notice required

by exhibit A.

1.7. “Larger work” means a work which combines covered code

or portions thereof with code not governed by the terms

of this License.

1.8. “License” means this document.

1.8.1. “Licensable” means having the right to grant, to the maxi-

mum extent possible, whether at the time of the initial

grant or subsequently acquired, any and all of the rights

conveyed herein.

1.9. “Modifications” means any addition to or deletion from

the substance or structure of either the original code or

any previous modifications. When covered code is

released as a series of files, a modification is:

A. Any addition to or deletion from the contents of a file

containing original code or previous modifications.

B. Any new file that contains any part of the original code

or previous modifications.

1.10. “Original code” means source code of computer software

code which is described in the source code notice

required by exhibit as original code, and which, at the time

of its release under this license is not already covered

code governed by this license.

1.10.1.

“Patent claims” means any patent claim(s), now owned or

hereafter acquired, including without limitation, method,

process, and apparatus claims, in any patent licensable by

grantor.

1.11. “Source code” means the preferred form of the covered

code for making modifications to it, including all modules

it contains, plus any associated interface definition files,

scripts used to control compilation and installation of an

executable, or source code differential comparisons

against either the original code or another well known,

available covered code of the contributor's choice. The

source code can be in a compressed or archival form, pro-

vided the appropriate decompression or de-archiving soft-

ware is widely available for no charge.

1.12. “You” (or “Your”) means an individual or a legal entity

exercising rights under, and complying with all of the terms

of, this license or a future version of this license issued

under section 6.1.

For legal entities, “You” includes any entity which controls,

is controlled by, or is under common control with You. For

purposes of this definition, “control” means (a) the power,

direct or indirect, to cause the direction or management of

such entity, whether by contract or otherwise, or (b) own-

ership of more than fifty percent (50%) of the outstand-

ing shares or beneficial ownership of such entity.

2. Source Code License.

2.1. The initial developer grant.

The initial developer hereby grants You a world-wide, roy-

alty-free, non-exclusive license, subject to third party intel-

lectual property claims:

a) under intellectual property rights (other than patent or

trademark) licensable by initial developer to use, repro-

duce, modify, display, perform, sublicense and distrib-

ute the original code (or portions thereof) with or with-

out modifications, and/or as part of a larger work; and

(b) under patents claims infringed by the making, using or

selling of original code, to make, have made, use, prac-

tice, sell, and offer for sale, and/or otherwise dispose

of the original code (or portions there of).

MOZILLA PUBLIC LICENSE

Version 1.1

---------------

APPENDIX

130

effective on the date Initial developer first distributes

original code under the terms of this license.

(d) Notwithstanding section 2.1(b) above, no patent

license is granted: 1) for code that You delete from the

original Code; 2) separate from the original code; or

3) for infringements caused by: i) the modification of

the original code or ii) the combination of the original

code with other software or devices.

2.2. Contributor Grant.

Subject to third party intellectual property claims, each

contributor hereby grants You a world-wide, royalty-free,

non-exclusive license

(a) under intellectual property rights (other than patent

or trademark) licensable by contributor, to use,

reproduce, modify, display, perform, sublicense and

distribute the modifications created by such contribu-

tor (or portions thereof) either on an unmodified

basis, with other modifications, as covered code

and/or as part of a larger work; and

(b) under patent claims infringed by the making, using, or

selling of modifications made by that contributor

either alone and/or in combination with its contributor

version (or portions of such combination), to make,

use, sell, offer for sale, have made, and/or otherwise

dispose of: 1) modifications made by that contributor

(or portions thereof); and 2) the combination of mod-

ifications made by that contributor with its contributor

version (or portions of such combination).

effective on the date contributor first makes commer-

cial use of the covered code.

(d) Notwithstanding section 2.2(b) above, no patent

license is granted: 1) for any code that contributor has

deleted from the contributor version; 2) separate from

the contributor version; 3) for infringements caused

by: i) third party modifications of contributor version

or ii) the combination of modifications made by that

contributor with other software (except as part of the

contributor version) or other devices; or 4) under

patent claims infringed by covered code in the

absence of modifications made by that contributor.

3. Distribution Obligations.

3.1. Application of license.

The modifications which You create or to which you con-

tribute are governed by the terms of this license, including

without limitation section 2.2. The source code version of

covered code may be distributed only under the terms of

this license or a future version of this license released

under section 6.1, and you must include a copy of this

license with every copy of the source code you distribute.

You may not offer or impose any terms on any source code

version that alters or restricts the applicable version of

this license or the recipients' rights hereunder. However,

you may include an additional document offering the

additional rights described in section 3.5.

3.2. Availability of source code.

Any modification which you create or to which you con-

tribute must be made available in source code form under

the terms of this license either on the same media as an

executable version or via an accepted electronic distribu-

tion mechanism to anyone to whom you made an exe-

cutable version available; and if made available via elec-

tronic distribution mechanism, must remain available for at

least twelve (12) months after the date it initially became

available, or at least six (6) months after a subsequent

version of that particular modification has been made

available to such recipients. You are responsible for ensur-

ing that the source code version remains available even if

the electronic distribution mechanism is maintained by a

third party.

3.3. Description of modifications.

You must cause all covered code to which you contribute to

contain a file documenting the changes You made to create

that covered code and the date of any change. You must

include a prominent statement that the modification is

derived, directly or indirectly, from original code provided by

the initial developer and including the name of the initial

developer in (a) the source code, and (b) in any notice in an

executable version or related documentation in which you

describe the origin or ownership of the covered code.

3.4. Intellectual property matters

(a) Third party claims.

If contributor has knowledge that a license under a third

party's intellectual property rights is required to exercise

the rights granted by such contributor under sections 2.1

or 2.2, contributor must include a text file with the source

code distribution titled "LEGAL" which describes the claim

and the party making the claim in sufficient detail that a

recipient will know whom to contact. If contributor obtains

such knowledge after the modification is made available as

described in section 3.2, contributor shall promptly modi-

fy the LEGAL file in all copies contributor makes available

thereafter and shall take other steps (such as notifying

appropriate mailing lists or newsgroups) reasonably calcu-

lated to inform those who received the covered code that

new knowledge has been obtained.

(b) Contributor APIs.

If contributor's modifications include an application

programming interface and contributor has knowledge of

patent licenses which are reasonably necessary to implement

that API, contributor must also include this information in

the LEGAL file.

APPENDIX

131

contributor represents that, except as disclosed pursuant

to section 3.4(a) above, contributor believes that contributor's

modifications are contributor's original creation(s)

and/or contributor has sufficient rights to grant the rights

conveyed by this license.

3.5. Required notices.

You must duplicate the notice in exhibit A in each file of

the source code. If it is not possible to put such notice in

a particular source code file due to its structure, then You

must include such notice in a location (such as a relevant

directory) where a user would be likely to look for such a

notice. If You created one or more modification(s), you

may add your name as a contributor to the notice

described in exhibit A. you must also duplicate this license

in any documentation for the source code where You

describe recipients' rights or ownership rights relating to

covered code. You may choose to offer, and to charge a

fee for, warranty, support, indemnity or liability obligations

to one or more recipients of covered code. However, you

may do so only on your own behalf, and not on behalf of

the Initial developer or any contributor. You must make it

absolutely clear than any such warranty, support, indemni-

ty or liability obligation is offered by you alone, and You

hereby agree to indemnify the Initial developer and every

contributor for any liability incurred by the Initial develop-

er or such contributor as a result of warranty, support,

indemnity or liability terms you offer.

3.6. Distribution of executable versions.

You may distribute covered code in executable form only if

the requirements of section 3.1-3.5 have been met for

that covered code, and if you include a notice stating that

the source code version of the covered code is available

under the terms of this license, including a description of

how and where you have fulfilled the obligations of section

3.2. The notice must be conspicuously included in any

notice in an executable version, related documentation or

collateral in which you describe recipients' rights relating

to the covered code. You may distribute the executable

version of covered code or ownership rights under a

license of your choice, which may contain terms different

from this license, provided that you are in compliance with

the terms of this license and that the license for the exe-

cutable version does not attempt to limit or alter the recip-

ient's rights in the source code version from the rights set

forth in this license. If you distribute the executable ver-

sion under a different license you must make it absolutely

clear that any terms which differ from this license are

offered by you alone, not by the Initial developer or any

contributor. You hereby agree to indemnify the initial

developer and every contributor for any liability incurred

by the initial developer or such contributor as a result of

any such terms You offer.

3.7. Larger works.

You may create a larger work by combining covered code

with other code not governed by the terms of this license

and distribute the larger work as a single product. In such

a case, you must make sure the requirements of this

license are fulfilled for the covered code.

4. Inability to comply due to statute or regulation.

If it is impossible for you to comply with any of the terms

of this license with respect to some or all of the covered

code due to statute, judicial order, or regulation then you

must: (a) comply with the terms of this license to the max-

imum extent possible; and (b) describe the limitations and

the code they affect. Such description must be included in

the LEGAL file described in section 3.4 and must be

included with all distributions of the source code. Except

to the extent prohibited by statute or regulation, such

description must be sufficiently detailed for a recipient of

ordinary skill to be able to understand it.

5. Application of this license.

This license applies to code to which the initial developer has

attached the notice in exhibit A and to related covered code.

6. Versions of the license.

6.1. New versions.

Netscape communications corporation (“Netscape”) may

publish revised and/or new versions of the license from

time to time. Each version will be given a distinguishing

version number.

6.2. Effect of new versions.

Once covered code has been published under a particular

version of the license, you may always continue to use it

under the terms of that version. You may also choose to

use such covered code under the terms of any subsequent

version of the license published by netscape. No one

other than netscape has the right to modify the terms

applicable to covered code created under this license.

6.3. Derivative works.

If You create or use a modified version of this license

(which you may only do in order to apply it to code which

is not already covered code governed by this license), You

must (a) rename Your license so that the phrases

"Mozilla", "MOZILLAPL", "MOZPL", "Netscape", "MPL",

"NPL" or any confusingly similar phrase do not appear in

your license (except to note that your license differs from

this license) and (b) otherwise make it clear that Your

version of the license contains terms which differ from the

Mozilla Public license and netscape Public License. (Filling

in the name of the initial developer, original code or con-

tributor in the notice described in exhibit A shall not of

themselves be deemed to be modifications of this license.)

APPENDIX

132

7. DISCLAIMER OF WARRANTY.

COVERED CODE IS PROVIDED UNDER THIS LICENSE

ON AN “AS IS” BASIS, WITHOUT WARRANTY OF ANY

KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,

WITHOUT LIMITATION, WARRANTIES THAT THE COV-

ERED CODE IS FREE OF DEFECTS, MERCHANTABLE, FIT

FOR A PARTICULAR PURPOSE OR NON-INFRINGING.

THE ENTIRE RISK AS TO THE QUALITY AND PERFOR-

MANCE OF THE COVERED CODE IS WITH YOU.

SHOULD ANY COVERED CODE PROVE DEFECTIVE IN

ANY RESPECT, YOU (NOT THE INITIAL DEVELOPER OR

ANY OTHER CONTRIBUTOR) ASSUME THE COST OF

ANY NECESSARY SERVICING, REPAIR OR CORRECTION.

THIS DISCLAIMER OF WARRANTY CONSTITUTES AN

ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY

COVERED CODE IS AUTHORIZED HEREUNDER EXCEPT

UNDER THIS DISCLAIMER.

8. TERMINATION.

8.1. This license and the rights granted hereunder will terminate

automatically if you fail to comply with terms herein and

fail to cure such breach within 30 days of becoming aware

of the breach. All sublicenses to the covered code which

are properly granted shall survive any termination of this

license. Provisions which, by their nature, must remain in

effect beyond the termination of this license shall survive.

8.2. If you initiate litigation by asserting a patent infringement

claim (excluding declatory judgment actions) against ini-

tial developer or a contributor (the initial developer or

contributor against whom you file such action is referred

to as “Participant”) alleging that:

(a) such participant's contributor version directly or indi-

rectly infringes any patent, then any and all rights

granted by such participant to you under sections 2.1

and/or 2.2 of this license shall, upon 60 days notice

from Participant terminate prospectively, unless if within

60 days after receipt of notice you either: (i) agree in

writing to pay participant a mutually agreeable reasonable

royalty for your past and future use of modifications

made by such participant, or (ii) withdraw your litigation

claim with respect to the contributor version against

such participant. If within 60 days of notice, a reasonable

royalty and payment arrangement are not mutually

agreed upon in writing by the parties or the litigation

claim is not withdrawn, the rights granted by partici-

pant to you under sections 2.1 and/or 2.2 automati-

cally terminate at the expiration of the 60 day notice

period specified above.

(b) any software, hardware, or device, other than such par-

ticipant's contributor Version, directly or indirectly

infringes any patent, then any rights granted to You by

such participant under sections 2.1(b) and 2.2(b) are

revoked effective as of the date you first made, used,

sold, distributed, or had made, modifications made by

that participant.

8.3. If you assert a patent infringement claim against partici-

pant alleging that such participant's contributor version

directly or indirectly infringes any patent where such claim

is resolved (such as by license or settlement) prior to the

initiation of patent infringement litigation, then the rea-

sonable value of the licenses granted by such participant

under sections 2.1 or 2.2 shall be taken into account in

determining the amount or value of any payment or

license.

8.4. In the event of termination under sections 8.1 or 8.2

above, all end user license agreements (excluding distributors

and resellers) which have been validly granted by you or

any distributor hereunder prior to termination shall survive

termination.

9. LIMITATION OF LIABILITY.

UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL

THEORY, WHETHER TORT (INCLUDING NEGLIGENCE),

CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL

DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DIS-

TRIBUTOR OF COVERED CODE,OR ANY SUPPLIER OF

ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR

ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN-

TIAL DAMAGES OF ANY CHARACTER INCLUDING, WITH-

OUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,

WORK STOPPAGE, COMPUTER FAILURE OR MALFUNC-

TION, OR ANY AND ALL OTHER COMMERCIAL DAM-

AGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE

BEEN INFORMED OF THE POSSIBILITY OF SUCH DAM-

AGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY

TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULT-

ING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT

APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME

JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM-

AGES, SO THIS EXCLUSION AND LIMITATION MAY NOT

APPLY TO YOU.

10. U.S. GOVERNMENT END USERS.

The covered code is a "commercial item," as that term is

defined in 48 C.F.R. 2.101 (Oct. 1995), consisting of

"commercial computer software" and "commercial computer

software documentation," as such terms are used in 48

C.F.R. 12.212 (Sept. 1995). Consistent with 48 C.F.R.

12.212 and 48 C.F.R. 227.7202-1 through 227.7202-4

(June 1995), all U.S. Government end users acquire cov-

ered code with only those rights set forth herein.

APPENDIX

133

11. MISCELLANEOUS.

This license represents the complete agreement concerning

subject matter hereof. If any provision of this license is

held to be unenforceable, such provision shall be reformed

only to the extent necessary to make it enforceable. This

License shall be governed by California law provisions

(except to the extent applicable law, if any, provides oth-

erwise), excluding its conflict-of-law provisions. With

respect to disputes in which at least one party is a citizen

of, or an entity chartered or registered to do business in

the united states of america, any litigation relating to this

License shall be subject to the jurisdiction of the federal

courts of the northern district of california, with venue

lying in santa clara county, california, with the losing party

responsible for costs, including without limitation, court

costs and reasonable attorneys' fees and expenses. The

application of the united nations convention on contracts

for the International sale of goods is expressly excluded.

Any law or regulation which provides that the language of

a contract shall be construed against the drafter shall not

apply to this license.

12. RESPONSIBILITY FOR CLAIMS.

As between initial developer and the contributors, each

party is responsible for claims and damages arising, directly

or indirectly, out of its utilization of rights under this

license and you agree to work with initial developer and

contributors to distribute such responsibility on an equitable

basis. Nothing herein is intended or shall be deemed to

constitute any admission of liability.

13. MULTIPLE-LICENSED CODE.

Initial developer may designate portions of the covered

code as "Multiple-Licensed". "Multiple-Licensed" means

that the initial developer permits you to utilize portions of

the covered code under your choice of the NPL or the

alternative licenses, if any, specified by the initial developer

in the file described in exhibit A.

EXHIBIT A -Mozilla Public License.

The contents of this file are subject to the Mozilla Public License

Version 1.1 (the “license”); you may not use this file except in

compliance with the License. You may obtain a copy of the

license at http://www.mozilla.org/MPL/

Software distributed under the license is distributed on an "AS

IS" basis, WITHOUT WARRANTY OF ANY KIND, either express

or implied. See the license for the specific language governing

rights and limitations under the License.

The Original Code is ______________________________________.

The Initial Developer of the Original Code

is___________________.

Portions created by ______________________ are Copyright (C)

Contributor(s): ______________________________________.

Alternatively, the contents of this file may be used under the

terms of the _____ license (the "[___] License"), in which case

the provisions of [______] license are applicable instead of those

above. If you wish to allow use of your version of this file only

under the terms of the [____] license and not to allow others to

use your version of this file under the MPL, indicate your decision

by deleting the provisions above and replace them with the

notice and other provisions required by the [___] license. If you

do not delete the provisions above, a recipient may use your version

of this file under either the MPL or the [___] license."

NOTE: The text of this exhibit A may differ slightly from the text

of the notices in the source code files of the original code. You

should use the text of this exhibit A rather than the text found in

the original code/source code for Your modifications.

Regulatory Information cont.

FCC Compliance Statement

This equipment has been tested and found to comply

within the limits of a Class B digital device pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses, and can radiate radio

frequency energy and if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio

or television reception (which can be determined by

turning the equipment on and off), the user is encouraged

to try to correct the interference by using one or more of

the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

the receiver.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV

technician for help.

Caution: Changes or modifications not expressly approved

by the party responsible for compliance could void the

user's (or your) authority to operate the equipment. Only

peripherals (digital input/output devices, terminals, printers,

etc.) certified to comply with the Class B limits may be

attached to this monitor. Operation with non-certified

peripherals is likely to result in interference to radio and TV

reception. Only shielded signal cables may be used with

this System.

Canadian DOC Notice

This Class B digital apparatus meets all requirements of

the Canadian Interference-Causing Equipment

Regulations. Cet appareil numérique de la classe B

respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

CE Conformity Notice

(for Europe)

Products with the “CE” Marking comply with the EMC

Directive(89/336/EEC) and LOW VOLTAGE Directive

(73/23/EEC) issued by the Commission of the European

Community.

Compiance with these directives implies conformity to the

following European Norms :

• EN 55022 ; Radio Frequency Interference

• EN 55024 ; Electromagnetic Immunity

• EN 61000-3-2 ; Power Line Harmonics

• EN 61000-3-3 ; Voltage Fluctuations

• EN 60950-1 ; Product Safety

Low Radiation Compliance (MPR II)

This monitor meets one of the strictest guidelines available

today for low radiation emissions, offering the user extra

shielding and an antistatic screen coating. These

guidelines, set forth by a government agency in Sweden,

limit the amount of emission allowed in the Extremely Low

Frequency (ELF) and Very Low Frequency (VLF)

electromagnetic range.

NOTICE

The regulations are applied only to the products with the

ID LABEL indicating specific requirements.

NOTICE

The regulations are applied only to the products with the

ID LABEL indicating specific requirements.

NOTICE

The regulations are applied only to the products with the

ID LABEL indicating specific requirements.

TCO'99 (TCO'99 applied model only)

Congratulations!

You have just purchased a TCO’99 approved and labelled

product! Your choice has provided you with a product

developed for professional use. Your purchase has also

contributed to reducing the burden on the environment and

also to the further development of environmentally

adapted electronics products.

Regulatory Information cont.

Why do we have environmentally labelled computers?

In many countries, environmental labelling has become an

established method for encouraging the adaptation of

goods and services to the environment. With the growing

manufacture and usage of electronic equipment

throughout the world, there is a recognized concern for the

materials and substances used by electronic products

with regards to their eventual recycling and disposal. By

proper selection of these materials and substances, the

impact on the environment can be minimized.

There are also other characteristics of a computer, such as

energy consumption levels, that are important from the

viewpoints of both the work (internal) and natural (external)

environments. Electronic equipment in offices is often left

running continuously, resulting in unnecessary

consumption of large amounts of energy and additional

power generation. From the standpoint of carbon dioxide

emissions alone, it is vital to save energy.

What does labelling involve?

The product meets the requirements for the TCO’99

scheme which provides for international and environmental

labelling of personal computers and/or displays.

The labelling scheme was developed as a joint effort by the

TCO (The Swedish Confederation of Professional

Employees), Svenska Naturskyddsforeningen

(The Swedish Society for Nature Conservation) and

Statens Energimyndighet (The Swedish National

Energy Administration).

Approval requirements cover a wide range of issues:

ecology, ergonomics, emission of electrical and magnetical

fields, energy consumption and electrical safety.

Ecological criteria impose restrictions on the presence and

use of heavy metals, brominated and chlorinated flame

retardants, and other substances. The product must be

prepared for recycling and the manufacturing site(s) shall

be certified according to ISO14001 or EMAS registered.

Energy requirements include a demand that the system

unit and/or display, after a certain period of inactivity,

shall reduce its power consumption to a lower level in one

or more stages. The length of time to reactivate the system

unit shall be reasonable for the user.

Labelled products must meet strict environmental

demands, for example, in respect of the reduction of

electrical and magnetical fields as well as work load and

visual ergonomics.

Below you will find a brief summary of the ecological

requirements met by this product. The complete

ecological criteria document can be found at TCO

Development’s website http://www.tcodevelopment.com

or may be ordered from:

TCO Development

SE-114 94 STOCKHOLM, Sweden

Fax: +46 8 782 92 07

Email : development@tco.se

Information regarding TCO’99 approved and labelled

products may also be obtained at

http://www.tcodevelopment.com

Ecological requirements

Flame retardants

Flame retardants may be present in printed wiring board

laminates, cables, and housings. Their purpose is to

prevent, or at least to delay the spread of fire. Up to 30%

by weight of the plastic in a computer casing can consist of

flame retardant substances. Many flame retardants

contain bromine or chlorine, and these flame retardants

are chemically related to PCBs (polychlorinated

biphenyls). Both the flame retardants containing bromine

or chlorine and the PCBs are suspected of giving rise to

health effects, including reproductive damage in fish-

eating birds and mammals, due to the bio-accumulative*

processes when not disposed of in accordance with strict

standards for disposal.

TCO’99 requires that plastic components weighing more

than 25 grams shall not contain flame retardants with

organically bound bromine or chlorine. Flame retardants

are allowed in the printed wiring board laminates due to

the lack of commercially available alternatives.

Cadmium**

Cadmium is present in rechargeable batteries and in the

colour-generating layers of certain computer displays.

TCO’99 requires that batteries, the colour-generating

layers of display screens, and the electrical or electronics

components shall not contain any cadmium.

Mercury**

Mercury is sometimes found in batteries, relays and

switches. TCO’99 requires that batteries shall not contain

any mercury. It also demands that mercury is not present

in any of the electrical or electronics components

associated with the labelled unit. There is however one

Regulatory Information cont.

exception. Mercury is, for the time being, permitted in the

back light system of flat panel monitors as there today is

no commercially available alternative. TCO aims on

removing this exception when a mercury free alternative is

available.

Lead**

Lead can be found in picture tubes, display screens,

solders and capacitors. TCO’99 permits the use of lead

due to the lack of commercially available alternatives, but

in future requirements TCO Development aims at

restricting the use of lead.

_____________________________________________

* Bio-accumulative is defined as substances which

accumulate in living organisms.

**Lead, Cadmium and Mercury are heavy metals

which are bio-accumulative.

TCO’03

(TCO’03 applied model only)

Congratulations!

The display you have just purchased carries the TCO’03

Displays label.

This means that your display is designed,manufactured

and tested according to some of the strictest quality and

environmental requirements in the world. This makes for a

high performance product, designed with the user in focus

that also minimizes the impact on our natural environment.

Some of the features of the TCO’03 Display requirements:

Ergonomics

• Good visual ergonomics and image quality in order to

improve the working environment for the user and to

reduce sight and strain problems. Important

parameters are luminance, contrast, resolution,

reflectance, colour rendition and image stability.

Energy

• Energy-saving mode after a certain time – beneficial

both for the user and the environment

• Electrical safety

Emissions

• Electromagnetic fields

• Noise emissions

Ecology

• The product must be prepared for recycling and the

manufacturer must have a certified environmental

management system such as EMAS or ISO 14 001

• Restrictions on

chlorinated and brominated flame retardants and

polymers

heavy metals such as cadmium, mercury and lead.

The requirements included in this label have been

developed by TCO Development in co-operation with

scientists, experts, users as well as manufacturers all over

the world. Since the end of the 1980s TCO has been

involved in influencing the development of IT equipment in

a more user-friendly direction. Our labelling system started

with displays in 1992 and is now requested by users and

IT-manufacturers all over the world.

For more information, please visit

www.tcodevelopment.com

Information for Environmental Preservation

LGE. announced the 'LG Declaration for a Cleaner

Environment' in 1994, and this ideal has served as a

guiding managerial principle ever since. The Declaration is

a foundation that has allowed us to undertake

environmentally friendly activities in careful consideration

of economic, environmental, and social aspects.

We promote activities for environmental preservation, and

we specifically develop our products to embrace the

concept of environment-friendly.

We minimize the hazardous materials contained in our

products. For example, there is no cadmium to be found in

our monitors.

Information for recycling

This monitor may contain parts which could be hazardous

to the environment. It is important that this monitor be

recycled after use.

LGE. handles all waste monitors through an

environmentally acceptable recycling method. There are

several take-back and recycling systems currently in

English

Regulatory Information cont.

operation worldwide. Many parts will be reused and

recycled, while harmful substances and heavy metals are

treated by an environmentally friendly method.

If you want to find out more information about our

recycling program, please contact your local LG vendor or

a corporate representative of LG.

We set our vision and policies on a cleaner world by

selecting the issue of the global environment as a task for

corporate improvement. Please visit our website for more

information about our ‘green’ policies.

http://www.lge.com/about/environment/html/Recycling.jsp

Informationen zur Erhaltung der Umwelt

Im Jahr 1994 verkündete LGE die 'LG Declaration for a

Cleaner Environment' (LG Erklärung für eine sauberere

Umwelt). Seitdem dient dieses Ideal als führendes Prinzip

des Unternehmens. Diese Erklärung war die Basis für die

Durchführung von

umweltfreundlichen Aktivitäten, wobei wirtschaftliche,

umweltbezogene und soziale Aspekte in die

Überlegungen mit einbezogen wurden.

Wir fördern Aktivitäten zum Schutz der Umwelt und die

Entwicklung unserer Produkte ist darauf ausgerichtet,

unserem Konzept bezüglich Umweltfreundlichkeit gerecht

zu werden.

Wir sind darauf bedacht, den Anteil der in unseren

Produkten enthaltenen schädlichen Materialien zu

minimieren. So ist in unseren Monitoren beispielsweise

kein Kadmium zu finden.

Informationen zum Thema Recycling

Dieser Monitor enthält Teile, die umweltschädlich sein

können. Es ist unbedingt erforderlich, dass der Monitor

recycelt wird, nachdem er außer Dienst gestellt wurde.

Bei LGE. werden alle ausrangierten Monitore in einem

unter umweltbezogenen Aspekten geeigneten Verfahren

recycelt. Augenblicklich sind weltweit mehrere

Rücknahme- und Recyclingsysteme im Einsatz. Viele

Teile werden wieder verwendet und recycelt. Schädliche

Substanzen und Schwermetalle werden durch

umweltverträgliche Verfahren behandelt.

Falls Sie mehr über unser Recyclingprogramm erfahren

möchten, wenden Sie sich bitte an Ihren lokalen LG-

Händler oder einen Unternehmensvertreter von LG.

Wir richten unsere Firmenpolitik auf eine sauberere

Umwelt hin aus, indem wir umweltspezifische Aspekte als

wichtigen Punkt in die Weiterentwicklung unseres

Unternehmens einfließen lassen. Zusätzliche

Informationen über unsere ‘grüne’ Firmenpolitik erhalten

Sie auf unserer Website.

http://www.lge.com/about/environment/html/Recycling.jsp

Information sur la protection del’environnement

LGE. a publié sa 'Déclaration en faveur d’un

environnement plus propre' en 1994 et celle-ci est restée,

depuis lors, un principe directeur de notre entreprise.

Cette déclaration a servi de base à notre réflexion et nous

a permis de prendre en compte à la fois les aspects

économiques et sociaux de nos activités, tout en

respectant l’environnement.

Nous encourageons les activités en faveur de la

préservation de l’environnement et c’est dans cet esprit

que nous développons nos produits : nous réduisons au

minimum les matières dangereuses qui entrent dans leur

composition et l’on ne trouve pas de cadmium, par

exemple, dans nos moniteurs.

Information sur le recyclage

Ce moniteur peut contenir des composants qui présentent

un risque pour l’environnement. Il est donc important que

celui-ci soit recyclé après usage.

LGE. traite les moniteurs en fin de cycle conformément à

une méthode de recyclage respectueuse de

l’environnement. Nous reprenons nos produits et les

recyclons dans plusieurs sites répartis dans le monde

entier. De nombreux composants sont réutilisés et

recyclés, et les matières dangereuses, ainsi que les

métaux lourds, sont traités selon un procédé écologique.

Si vous souhaitez plus de renseignements sur notre

programme de recyclage, veuillez contacter votre

revendeur LG ou un l’un de nos représentants.

Nous voulons agir pour un monde plus propre et croyons

au rôle de notre entreprise dans l’amélioration de

l’environnement. Pour plus de renseignements sur notre

politique “verte”, rendez visite à notre site :

http://www.lge.com/about/environment/html/Recycling.jsp

Deutsch

Français

Regulatory Information cont.

Informazioni per la tutela dell’ambiente

La LGE. ha annunciato nel 1994 la cosiddetta 'LG

Declaration for a Cleaner Environment' (Dichiarazione di

LG a favore di un ambiente più pulito), un ideale che da

allora funge da principio ispiratore della gestione

aziendale. La dichiarazione rappresenta il fondamento che

consente di intraprendere attività a favore dell'ambiente

tenendo conto degli aspetti economici, ambientali e

sociali.Noi della LG, promuoviamo attività a favore della

tutela dell'ambiente sviluppando appositamente i nostri

prodotti per cogliere il concetto del rispetto dell’ambiente

riducendo i materiali dannosi presenti nei nostri prodotti.

Ad esempio nei nostri monitor non è presente il cadmio.

Informazioni per il riciclaggio

Il monitor può presentare componenti che potrebbero

risultare eventualmente dannosi per l'ambiente. È

importante che il monitor sia riciclato al termine del suo

utilizzo.

La LGE. gestisce tutti i monitor di rifiuto con un metodo di

riciclaggio soddisfacente dal punto di vista ambientale. In

tutto il mondo sono attualmente in funzione numerosi

sistemi di riciclaggio e recupero. I diversi componenti sono

riutilizzati e riciclati, mentre le sostanze dannose e i metalli

pesanti vengono trattati con un metodo rispettoso

dell’ambiente.

Se si desiderano maggiori informazioni in merito al

programma di riciclaggio, è consigliabile rivolgersi al

proprio rivenditore LG o ad un rappresentante aziendale

della LG.

Noi della LG impostiamo la nostra visione e le nostre

politiche a favore di un mondo più pulito ponendo la

questione dell'ambiente dal punto di vista globale come

una mansione rivolta al miglioramento della nostra

azienda. Vi invitiamo a visitare il nostro sito internet per

ulteriori informazioni sulla nostra politica “verde”.

http://www.lge.com/about/environment/html/Recycling.jsp

Información para la conservación

medioambiental

LGE. presentó la 'Declaración para un entorno más limpio

de LG' en 1994 y este ideal ha servido para guiar nuestros

principios empresariales desde entonces. La Declaración

es la base que nos ha permitido llevar a cabo tareas que

respetan el medio ambiente siempre teniendo en cuenta

aspectos sociales,

económicos y medioambientales.

Promocionamos actividades orientadas a la conservación

del medio ambiente y desarrollamos nuestros productos

específicamente para que se ajusten a la filosofía que

protege el entorno.

Reducimos al máximo el uso de materiales de riesgo en

nuestros productos. Un ejemplo de ello es la ausencia

total de cadmio en nuestros monitores.

Información para el reciclaje

Este monitor puede contener piezas que entrañen riesgos

medioambientales. Es importante reciclar este monitor

después de su utilización.

LGE. trata todos los monitores usados siguiendo un

método de reciclaje que no daña al entorno. Contamos

con diversos sistemas de recuperación y reciclaje que

funcionan a nivel mundial en la actualidad. Es posible

reciclar y reutilizar muchas de las piezas, mientras que las

sustancias dañinas y los metales pesados se tratan

siguiendo un método que no perjudique al medio

ambiente. Si desea obtener más información acerca del

programa de reciclaje, póngase en contacto con su

proveedor local de LG o con un representante empresarial

de nuestra marca.

Basamos nuestra visión y nuestras políticas en un mundo

más limpio y para ellos optamos por un entorno global

como tarea principal de nuestra evolución como empresa.

Visite nuestra página Web para obtener más información

sobre nuestras políticas ecológicas.

http://www.lge.com/about/environment/html/Recycling.jsp

Informações relacionadas à preservação

ambiental

A LGE. anunciou a 'LG Declaration for a Cleaner

Environment' (Declaração da LG para um ambiente mais

limpo) em 1994 e esse ideal tem servido desde então

como um princípio administrativo de orientação. A

Declaração é a base que nos tem permitido realizar

atividades favoráveis ao ambiente com consideração

atenta aos aspectos econômicos, ambientais e sociais.

Promovemos atividades de preservação ambiental e

desenvolvemos nossos produtos para englobar

Italiano

Espanõl

Português

Regulatory Information cont.

especificamente o conceito de favorável ao ambiente.

Reduzimos os materiais perigosos contidos em nossos

produtos. Por exemplo, não há cádmio em nossos

monitores.

Informações relacionadas à reciclagem

Este monitor pode conter peças que podem representar

riscos ao ambiente. É importante que ele seja reciclado

após o uso.

A LGE. cuida de todos os monitores descartados através

de um método de reciclagem agradável ao ambiente. Há

vários sistemas de devolução e reciclagem atualmente

em operação no mundo. Muitas peças serão reutilizadas

e recicladas e as substâncias nocivas e os metais

pesados passarão por tratamento através de um método

favorável ao ambiente.

Para obter mais informações sobre nosso programa de

reciclagem, entre em contato com seu fornecedor LG

local ou com um representante corporativo da LG.

Definimos nossa visão e nossas políticas relacionadas a

um mundo mais limpo selecionando a questão do

ambiente global como uma tarefa de aprimoramento

corporativo. Visite nosso site para obter mais informações

sobre nossas políticas de meio ambiente.

http://www.lge.com/about/environment/html/Recycling.jsp

Informatie met betrekking tot het behoud van

het milieu

LGE. publiceerde in 1994 de 'LG Declaration for a Cleaner

Environment' (de LG-verklaring met betrekking tot een

schoner milieu). Deze verklaring en het ideaal van een

schoner milieu fungeren sindsdien als een bestuurlijke

leidraad voor onze onderneming. Op basis van deze

verklaring ontplooien wij milieuvriendelijke activiteiten,

waarbij er zowel met sociale en economische aspecten,

als met milieuaspecten zorgvuldig rekening wordt

gehouden.

Wij ondersteunen activiteiten die zijn gericht op het

behoud van het milieu en wij houden bij het ontwikkelen

onze producten specifiek rekening met de

milieuvriendelijkheid van onze producten.

Wij minimaliseren het gebruik van schadelijke stoffen in

onze producten. Er wordt bijvoorbeeld geen cadmium

verwerkt in onze monitors.

Nederlands

Informatie met betrekking tot recycling

Deze monitor bevat materialen die schadelijk zouden

kunnen zijn voor het milieu. Het is belangrijk dat deze

monitor aan het einde van zijn levensduur wordt

gerecycled.

LGE. verwerkt alle afvalmonitors via een milieuvriendelijke

recyclingmethode. Hiervoor worden er momenteel

wereldwijd verscheidene inname- en recyclingsystemen

gehanteerd. Een groot aantal onderdelen wordt opnieuw

gebruikt en gerecycled, waarbij schadelijke stoffen en

zware metalen volgens een milieuvriendelijke methode

worden verwerkt.

Voor meer informatie over ons recyclingprogramma kunt u

contact opnemen met uw plaatselijke LG-

vertegenwoordiger of een LG-vestiging.

Onze visie en ons beleid met betrekking tot een schonere

wereld vloeien voort uit het feit dat wij het milieu hebben

aangemerkt als een onderwerp dat speciale aandacht

verdient binnen onze onderneming. Bezoek onze website

voor meer informatie over ons 'groene' beleid.

http://www.lge.com/about/environment/html/Recycling.jsp

»ÌÙÓÏ‡ˆËˇ ÔÓ Óı‡ÌÂ ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚

¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡

'ƒÂÍÎ‡‡ˆË˛ LG ÔÓ Óı‡ÌÂ ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚',

ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔËÌˆËÔÓÏ

ÛÔ‡‚ÎÂÌËˇ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍÎ‡‡ˆËË Ï˚ ÒÏÓ„ÎË

ÔÂ‰ÔËÌˇÚ¸ ‰ÂÈÒÚ‚Ëˇ, Ó·ÂÒÔÂ˜Ë‚‡˛˘ËÂ

·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚, Û‰ÂÎˇˇ ÔË ˝ÚÓÏ

‰ÓÎÊÌÓÂ ‚ÌËÏ‡ÌËÂ ˝ÍÓÌÓÏË˜ÂÒÍËÏ, ˝ÍÓÎÓ„Ë˜ÂÒÍËÏ Ë

ÒÓˆË‡Î¸Ì˚Ï ‡ÒÔÂÍÚ‡Ï.

Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂÎ¸ÌÓÒÚ¸ ÔÓ Óı‡ÌÂ

ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚, Û‰ÂÎˇˇ ÓÒÓ·ÓÂ ‚ÌËÏ‡ÌËÂ

‡Á‡·ÓÚÍÂ Ì‡¯ÂÈ ÔÓ‰ÛÍˆËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË Ò

ÍÓÌˆÂÔˆËÂÈ ˝ÍÓÎÓ„Ë˜ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË.

Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂÊ‡ÌËÂ ÓÔ‡ÒÌ˚ı

‚Â˘ÂÒÚ‚ ‚ Ì‡¯ÂÈ ÔÓ‰ÛÍˆËË. Õ‡ÔËÏÂ, ‚ Ì‡¯Ëı

ÏÓÌËÚÓ‡ı ‚˚ ÌÂ Ì‡È‰ÂÚÂ Í‡‰ÏËˇ.

»ÌÙÓÏ‡ˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚

›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰ÂÊ‡Ú¸ ÍÓÏÔÓÌÂÌÚ˚,

ÍÓÚÓ˚Â ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰Â.

Russian

Regulatory Information cont.

EPA

(EPA applied model only)

ENERGY STAR

is a set of power-saving guidelines

issued by the U.S. Environmental Protection

Agency(EPA).

NOM MARK (Mexico only)

ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂ

ËÒÔÓÎ¸ÁÓ‚‡ÌËˇ.

KÓÔÓ‡ˆËˇ LGE ÔÂÂ‡·‡Ú˚‚‡ÂÚ ‚ÒÂ ·‡ÍÓ‚‡ÌÌ˚Â

ÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎÓ„Ë˜ÂÒÍË ÔËÂÏÎÂÏÓ„Ó

ÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ

‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡

ËÒÔÓÎ¸ÁÓ‚‡ÌÌÓÈ ÔÓ‰ÛÍˆËË. ÃÌÓ„ËÂ ÍÓÏÔÓÌÂÌÚ˚

·Û‰ÛÚ ‚ÚÓË˜ÌÓ ËÒÔÓÎ¸ÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ

‚ÂÏˇ Í‡Í ‚Â‰Ì˚Â ‚Â˘ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚Â ÏÂÚ‡ÎÎ˚

·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎÓ„Ë˜ÂÒÍË

ÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.

«‡ ·ÓÎÂÂ ÔÓ‰Ó·ÌÓÈ ËÌÙÓÏ‡ˆËÂÈ ÔÓ Ì‡¯ÂÈ

ÔÓ„‡ÏÏÂ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ Í

ÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË ÔÂ‰ÒÚ‡‚ËÚÂÎ˛

ÍÓÔÓ‡ˆËË LG.

Ã˚ ÓËÂÌÚËÛÂÏÒˇ Ì‡ Ó·ÂÒÔÂ˜ÂÌËÂ ˝ÍÓÎÓ„Ë˜ÂÒÍÓÈ

·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ ÒÂ·Â ˆÂÎ¸˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛ

ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚. ƒÓÔÓÎÌËÚÂÎ¸ÌÛ˛ ËÌÙÓÏ‡ˆË˛

Ó Ì‡¯ÂÈ ÔÓÎËÚËÍÂ ÔÓ Óı‡ÌÂ ÓÍÛÊ‡˛˘ÂÈ ÒÂ‰˚ ‚˚

ÏÓÊÂÚÂ Ì‡ÈÚË Ì‡ Ì‡¯ÂÏ Ò‡ÈÚÂ:

http://www.lge.com/about/environment/html/Recycling.jsp

As an ENERGY STAR Partner LGE U. S.

A.,Inc. has determined that this product

meets the ENERGY STAR guidelines for

energy efficiency.

Regulatory Information cont.

1.When this crossed-out wheeled bin symbol is attached

to a product it means the product is covered by the

European Directive 2002/96/EC.

2.All electrical and electronic products should be

disposed of separately from the municipal waste

stream via designated collection facilities appointed by

the government or the local authorities.

3.The correct disposal of your old appliance will help

prevent potential negative consequences for the

environment and human health.

4.For more detailed information about disposal of your

old appliance, please contact your city office, waste

disposal service or the shop where you purchased the

product.

Disposal of your old appliance

1.Quando su un prodotto è riportato il simbolo di

1.När den här symbolen med en överkryssad

soptunna på hjul sitter på en produkt innebär det

att den regleras av European Directive

2002/96/EC.

2.Alla elektriska och elektroniska produkter bör

kasseras via andra vägar än de som finns för

hushållsavfall, helst via för ändamålet avsedda

uppsamlingsanläggningar som myndigheterna

utser.

3.Om du kasserar din gamla apparat på rätt sätt

så bidrar du till att förhindra negativa

konsekvenser för miljön och människors hälsa.

4.Mer detaljerad information om kassering av din

gamla apparat kan får av kommunen,

renhållningsverket eller den butik där du köpte

produkten.

1.Als het symbool met de doorgekruiste verrijdbare

afvalbak op een product staat, betekent dit dat

het product valt onder de Europese Richtlijn

2002/96/EC.

2.Elektrische en elektronische producten mogen

niet worden meegegeven met het huishoudelijk

afval, maar moeten worden ingeleverd bij

speciale inzamelingspunten die door de lokale of

landelijke overheid zijn aangewezen.

3.De correcte verwijdering van uw oude toestel

helpt negatieve gevolgen voor het milieu en de

menselijke gezondheid voorkomen.

Smaltimento delle apparecchiature obsolete

Kassering av din gamla apparat

Uw oude toestel wegdoen

1.Ce symbole, représentant une poubelle sur

roulettes barrée d'une croix, signifie que le

produit est couvert par la directive européenne

2002/96/EC.

2.Les éléments électriques et électroniques

doivent être jetés séparément, dans les vide-

ordures prévus à cet effet par votre municipalité.

3.Une élimination conforme aux instructions aidera

à réduire les conséquences négatives et risques

éventuels pour l'environnement et la santé

humaine.

4.Pour plus d'information concernant l'élimination

de votre ancien appareil, veuillez contacter votre

mairie, le service des ordures ménagères ou

encore la magasin où vous avez acheté ce

produit.

Élimination de votre ancien appareil

un bidone della spazzatura barrato da una croce

significa che il prodotto è coperto dalla direttiva

europea 2002/96/EC.

2.Tutti i prodotti elettrici ed elettronici dovrebbero

essere smaltiti separatamente rispetto alla

raccolta differenziata municipale, mediante

impianti di raccolta specifici designati dal

governo o dalle autorità locali.

3.Il corretto smaltimento delle apparecchiature

obsolete contribuisce a prevenire possibili

conseguenze negative sulla salute umana e

sull'ambiente.

4.Per informazioni più dettagliate sullo smaltimento

delle apparecchiature obsolete, contattare il

comune, il servizio di smaltimento rifiuti o il

negozio in cui è stato acquistato il prodotto.

English

French

Italian

Swedish

Dutch

WEEE (for Europe )

Regulatory Information cont.

1.Wenn dieses Symbol eines durchgestrichenen

Abfalleimers auf einem Produkt angebracht ist,

unterliegt dieses Produkt der europäischen

Richtlinie 2002/96/EC.

2.Alle Elektro- und Elektronik-Altgeräte müssen

getrennt vom Hausmüll über dafür staatlich

vorgesehenen Stellen entsorgt werden.

3.Mit der ordnungsgemäßen Entsorgung des alten

Geräts vermeiden Sie Umweltschäden und eine

Gefährdung der persönlichen Gesundheit.

4.Weitere Informationen zur Entsorgung des alten

Geräts erhalten Sie bei der Stadtverwaltung,

beim Entsorgungsamt oder in dem Geschäft, wo

Sie das Produkt erworben haben.

1.ŸÙ·Ó ¤Ó· ÚÔ˚ﬁÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓﬁ˜

‰È·ÁÚ·ÌÌ¤ÓÔ˘ Î¿Ï·ıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙﬁÙÂ ÙÔ ÚÔ˚ﬁÓ

Î·Ï‡ÙÂÙ·È ·ﬁ ÙËÓ E˘Úˆ·˚Î‹ O‰ËÁ›· 2002/96/EOK.

2.H ·ﬁÚÚÈ„Ë ﬁÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓ

ÚÔ˚ﬁÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿ ·ﬁ Ù· ÁÂÓÈÎ¿

ÔÈÎÈ·Î¿ ·ÔÚÚ›ÌÌ·Ù· Ì¤Ûˆ Î·ıÔÚÈÛÌ¤ÓˆÓ

ÂÁÎ·Ù·ÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ ÔÔ›Â˜

¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËıÂ› Â›ÙÂ ·ﬁ ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·ﬁ ÙÈ˜

ÙÔÈÎ¤˜ ·Ú¯¤˜.

3.H ÛˆÛÙ‹ ·ﬁÚÚÈ„Ë ÙË˜ ·ÏÈ¿˜ Û·˜ Û˘ÛÎÂ˘‹˜ ı·

‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓ

ˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘ÁÂ›· ÙÔ˘ ·ÓıÚÒÔ˘.

4.°È· ÈÔ ÏÂÙÔÌÂÚÂ›˜ ÏËÚÔÊÔÚ›Â˜ Û¯ÂÙÈÎ¿ ÌÂ ÙËÓ

·ﬁÚÚÈ„Ë ÙË˜ ·ÏÈ¿˜ Û·˜ Û˘ÛÎÂ˘‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙÂ ÌÂ

ÙÔ ·ÚÌﬁ‰›Ô ÙÔÈÎﬁ ÁÚ·ÊÂ›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛË˜ ÔÈÎÈ·ÎÒÓ

·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·ﬁ ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·ÙÂ ÙÔ

ÚÔ˚ﬁÓ.

1.Tämä merkki tuotteessa tarkoittaa, että tuote

kuuluu sähkö- ja elektroniikkalaiteromusta

annetun EU-direktiivin 2002/96/EY

soveltamisalaan.

2.Kaikki elektroniset laitteet ovat ongelmajätettä,

joten ne on toimitettava paikalliseen

keräyspisteeseen.

3.Vanhan laitteen asianmukainen hävittäminen

ehkäisee mahdollisia ympäristöön ja

terveyteen kohdistuvia haittavaikutuksia.

4.Lisätietoa vanhan laitteen hävittämisestä saat

ottamalla yhteyden paikallisiin viranomaisiin,

kierrätyskeskukseen tai myymälään, josta ostit

laitteen.

1.Når der er et tegn med et kryds over en

skraldespand, betyder det, at produktet er

omfattet af EU-direktiv 2002/96/EC.

2.Alle elektriske og elektroniske produkter skal

smides ud et andet sted end gennem den

kommunale affaldsordning ved hjælp af specielle

indsamlingsfaciliteter, der er organiseret af staten

1.Si en un producto aparece el símbolo de un contenedor

de basura tachado, significa que éste se acoge a la

Directiva 2002/96/CE.

2.Todos los aparatos eléctricos o electrónicos se deben

desechar de forma distinta del servicio municipal de

recogida de basura, a través de puntos de recogida

designados por el gobierno o las autoridades locales.

3.La correcta recogida y tratamiento de los dispositivos

inservibles contribuye a evitar riesgos potenciales para el

medio ambiente y la salud pública.

4.Para obtener más información sobre cómo deshacerse de

sus aparatos eléctricos y electrónicos viejos, póngase en

contacto con su ayuntamiento, el servicio de recogida de

basuras o el establecimiento donde adquirió el producto.

Vanhojen laitteiden hävittäminen

Entsorgung von Altgeräten

Sådan smider du dit gamle apparat ud

∞ﬁÚÚÈ„Ë ÙË˜ ·ÏÈ¿˜ Û·˜ Û˘ÛÎÂ˘‹˜

Cómo deshacerse de aparatos eléctricos y

electrónicos viejos

eller de lokale myndigheder.

3.Korrekt bortskaffelse af dit gamle apparat er med

til at forhindre mulige skadevirkninger på miljøet

og menneskelig sundhed.

4.Mere detaljerede oplysninger om bortskaffelse af

dit gamle apparat kan fås ved at kontakte dit

lokale kommunekontor, renovationsselskab eller

den butik, hvor du købte produktet.

Finnish

German

Danish

Greek

Spanish

4.Wilt u meer informatie over de verwijdering van

uw oude toestel? Neem dan contact op met uw

gemeente, de afvalophaaldienst of de winkel

waar u het product hebt gekocht.

Regulatory Information cont.

Portuguese

Slovak

Czech

Croatian

Hungarian

Polish

Regulatory Information cont.

Estonian

Latvian

Lithuanian

LG Electronics USA 37LG710HUA LCD TV MONITOR User Manual User s Manual G

LG Electronics USA LCD TV MONITOR User s Manual G

USERS MANUAL

Navigation menu

Namespaces

Views

Navigation