LG Electronics USA 42LG61UA LCD TV/MONITOR User Manual Manual 42LG61 UA 1

LG Electronics USA LCD TV/MONITOR Manual 42LG61 UA 1

Contents

User manual 1 of 2

Please read this manual carefully before operatingyour set. Retain it for future reference.Record model number and serial number of the set. See the label attached on the back cover and quote this information to your dealer when you require service.LCD TV PLASMA TVOWNER’S MANUALLCD TV MODELS32LG30 37LG5037LG30 42LG5042LG30 47LG5042LGX 52LG5032LG60 32LG7037LG60 42LG7042LG60 47LG7047LG60 52LG7052LG6047 LG 90PLASMA TV MODELS42PG2550PG2550PG6060PG6050PG7060PG70P/NO : SAC30708020 (0804-REV05)www.lgusa.com / www.lg.caAs an ENERGY STAR PartnerLG Electronics USA, Inc.has determined that thisproduct meets the ENERGYSTAR guidelines for energyefficiency.ENERGY STAR is a set of power-savingguidelines issued by the U.S.Environmental Protection Agency (EPA).
1WARNING / CAUTIONWARNING / CAUTIONTo prevent fire or shock hazards, do not exposethis product to rain or moisture.FCC NOTICEClass B digital deviceThis equipment has been tested and found to complywith the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference toradio or television reception, which can be determinedby turning the equipment off and on, the user isencouraged to try to correct the interference by oneor more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment andreceiver.- Connect the equipment to an outlet on a circuitdifferent from that to which the receiver is connected.- Consult the dealer or an experienced radio/TVtechnician for help.Any changes or modifications not expressly approvedby the party responsible for compliance could voidthe user’s authority to operate the equipment.CAUTIONDo not attempt to modify this product in any waywithout written authorization from LG Electronics.Unauthorized modification could void the user’sauthority to operate this product The lightning flash with arrowheadsymbol, within an equilateral triangle, isintended to alert the user to the presenceof uninsulated “dangerous voltage” within theproduct’s enclosure that may be of sufficientmagnitude to constitute a risk of electric shock topersons.The exclamation point within an equilateraltriangle is intended to alert the user tothe presence of important operating andmaintenance (servicing) instructions in the litera-ture accompanying the appliance.TO REDUCE THE RISK OF ELECTRIC SHOCKDO NOT REMOVE COVER (OR BACK). NOUSER SERVICEABLE PARTS INSIDE. REFER TOQUALIFIED SERVICE PERSONNEL.WARNING/CAUTIONTO REDUCE THE RISK OF FIRE AND ELECTRICSHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.NOTE TO CABLE/TV INSTALLERThis reminder is provided to call the CATV systeminstaller’s attention to Article 820-40 of the NationalElectric Code (U.S.A.). The code provides guidelines forproper grounding and, in particular, specifies that thecable ground shall be connected to the grounding systemof the building, as close to the point of the cable entryas practical.
2IMPORTANT SAFETY INSTRUCTIONSSAFETY INSTRUCTIONSImportant safety instructions shall be provided with each apparatus. This information shall be given in a separatebooklet or sheet, or be located before any operating instructions in an instruction for installation for use andsupplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safetyinstructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safetyinformation may be included by adding statements after the end of the following safety instruction list. At themanufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may beplaced immediately adjacent to that safety instruction:Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.Do not install near any heat sources such asradiators, heat registers, stoves, or other apparatus(including amplifiers)that produce heat.When mounting a TV it on the wall, make surenot to install TV by the hanging power and sig-nal cables on the back of the TV.Do not defeat the safety purpose of the polarizedor grounding-type plug. A polarized plug hastwo blades with one wider than the other. Agrounding type plug has two blades and a thirdgrounding prong, The wide blade or the thirdprong are provided for your safety. If the providedplug does not fit into your outlet, consult anelectrician for replacement of the obsolete outlet.Protect the power cord from being walked onor pinched particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.Only use attachments/accessories specified bythe manufacturer.Unplug this apparatus during lighting stormsor when unused for long periods of time.123456789
3Use only with the cart, stand, tripod, bracket,or table specified by the manufacturer, or soldwith the apparatus. When a cart is used, usecaution when moving the cart/apparatuscombination to avoid injury from tip-over.Never touch this apparatus or antenna duringa thunder or lighting storm. Do not allow a impact shock or any objects tofall into the product, and do not drop onto thescreen with something.Refer all servicing to qualified service personnel.Servicing is required when the apparatus hasbeen damaged in any way, such as power-supplycord or plug is damaged, liquid has beenspilled or objects have fallen into the apparatus,the apparatus has exposed to rain or moisture,does not operate normally, or has beendropped.CAUTION concerning the Power Cord :Most appliances recommend they be placedupon a dedicated circuit; that is, a single outletcircuit which powers only that appliance andhas no additional outlets or branch circuits.Check the specification page of this owner'smanual to be certain.Do not overload wall outlets. Overloaded walloutlets, loose or damaged wall outlets, extensioncords, frayed power cords, or damaged orcracked wire insulation are dangerous. Any ofthese conditions could result in electric shockor fire. Periodically examine the cord of yourappliance, and if its appearance indicates dam-age or deterioration, unplug it, discontinue useof the appliance, and have the cord replacedwith an exact replacement part by an authorizedservicer. Protect the power cord from physicalor mechanical abuse, such as being twisted,kinked, pinched, closed in a door, or walkedupon. Pay particular attention to plugs, walloutlets, and the point where the cord exits theappliance.Outdoor use marking :WARNING - To reduce the risk of fire or elec-tric shock, do not expose this appliance to rainor moisture.Wet Location Marking : Apparatus shall not beexposed to dripping or splashing and noobjects filled with liquids, such as vases, shallbe placed on or over apparatus.GROUNDINGEnsure that you connect the earth ground wireto prevent possible electric shock. If groundingmethods are not possible, have a qualifiedelectrician install a separate circuit breaker. Do not try to ground the unit by connecting itto telephone wires, lightening rods, or gas pipes.DISCONNECTING DEVICE FROM MAINSMains plug is the disconnecting device. Theplug must remain readily operable.121011141315161718Power SupplyShort-circuitBreaker
4CONTENTSWARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 2FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6PREPARATIONAccessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Stand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Protection Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Securing the TV to the wall to prevent falling . . . . 21Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 22EXTERNAL EQUIPMENT SETUPHD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Audio Out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47WATCHING TV / CHANNEL CONTROLRemote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Turning On the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Channel Setup - Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 56- Add / Delete Channel (Manual Tuning) . . . . . . 57- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62USBEntry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69PICTURE CONTROLPicture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 72Preset Picture Settings- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75Manual Picture Adjustment- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 76- Picture Mode - Expert Control . . . . . . . . . . . . . . . . . . 77Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 78Advanced Control - Black (Darkness) Level . . . . . . . 79Advanced Control - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Advanced Control - Real Cinema/Film Mode . . . . . 81Advanced Control - TruMotion . . . . . . . . . . . . . . . . . . . . . . . . 82TruMotion Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Image Sticking Minimization (ISM) Method . . . . . . 86Power Saving Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
5SOUND & LANGUAGE CONTROLAuto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 88Preset Sound Settings (Sound Mode) . . . . . . . . . . . . . . 89Sound Setting Adjustment - User Mode . . . . . . . . . . . 90Clear Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94Stereo/SAP Broadcast Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 95Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96On-Screen Menus Language Selection . . . . . . . . . . . . . . 97Caption Mode- Analog Broadcasting System Captions . . . . . . . 98- Digital Broadcasting System Captions . . . . . . . . 99- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 0TIME SETTINGClock Setting- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105PARENTAL CONTROL / RATINGSSet Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117APPENDIXTroubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121Programming the Remote Control . . . . . . . . . . . . . . . . . . 124IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127External Control Through RS-232C . . . . . . . . . . . . . . . . .12 9Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
6FEATURE OF THIS TVis a trademark of SRS Labs, Inc.TruSurround XT technology is incorporated underlicense from SRS Labs, Inc.Manufactured under license from Dolby Laboratories.“Dolby“and the double-D symbol are trademarks ofDolby Laboratories. FOR LCD TV■If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there isnothing wrong with TV.■Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, theyhave no adverse effect on the monitor's performance.■Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may producesome temporary distortion effects on the screen.On Disposal (Only Hg lamp used LCD TV)The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product withgeneral household waste. Disposal of this product must be carried out in accordance to the regulations of your localauthority.
PREPARATION7PREPARATIONACCESSORIESEnsure that the following accessories are included with your TV. If an accessory is missing, please contact thedealer where you purchased the TV. The accessories included may differ from the images below.Option ExtrasFor LCD TV modelsFor Plasma TV models* Wipe spots on the exterior only withthe polishing cloth.* Do not wipe roughly when removingstain. Excessive pressure may causescratch or discoloration.Polishing Cloth(This feature is not availablefor all models.)Copyright© 2007 LGE,All Rights Reserved.D-sub 15 pin Cable1.5V 1.5VOwner’s Manual Power CordRemote Control,BatteriesINPUTFAVMUTETVSTBPOWERQ.MENUMENUAVMODERETURNENTERVOLCH1234567809FLASHBKPAGEDVDVCRCD ManualWhen using the VGA (D-sub 15 pincable) PC connection, the usermust use shielded signal interfacecables with ferrite cores to maintainstandards compliance.32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90Bolts for stand assembly(Refer to P.14)(Only 32/37/42LG30, 37/42LG50,32/42LG70)Protection Cover(Refer to P.20)Screw for stand fixing(Refer to P.18)(Only 32LG30/70, 42LG30/50)x 4 x 432/37/42/47/52LG60, 42LGXProtection Cover(Refer to P.20)Cable ManagementClip2EA(M4x16)4EA(M4x20)1EA 4EA 32LG60: 3EA37LG60: 4EABolts for stand assembly(Refer to P.15)(Only 32/37LG60) (Only 42LG60, 42LGX)Cable Management ClipProtection Cover(Refer to P.20)(Only 50PG25,50/60PG60, 50/60PG70)(Only 42PG25)ororCable HolderBolts for stand assembly(Refer to P.14)x 4
PREPARATION8FRONT PANEL INFORMATIONPREPARATION■Image shown may differ from your TV.■NOTE: If your TV has a protection tape attached, remove the tape.And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).Plasma TV ModelsCHVOLMENUINPUT ENTERINPUTButtonMENUButtonENTERButtonVOLUME(-, +) ButtonsCHANNEL(EE,D)ButtonsRemote Control SensorPOWER ButtonPower/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the TV is switched on.LCD TV ModelsPOWER ButtonPower/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the set is switched on.(Can be adjusted using Power Indicator inthe OPTION menu. Gp.85)CHVOLMENUINPUTENTERCHANNEL ( , ) ButtonsVOLUME (+, -) ButtonsENTER ButtonMENU ButtonINPUT ButtonIntelligent SensorAdjusts picture according to the surroundingconditions 32/42/47/52LG70, 47LG90Remote Control Sensor
PREPARATION9LCD TV ModelsPOWER ButtonPower/Standby IndicatorIlluminates red in standby mode.Illuminates blue when the set is switched on.(Can be adjusted using Power Indicator inthe OPTION menu. Gp.85)CHVOLMENUINPUTENTERCHANNEL ( , ) ButtonsVOLUME (+, -) ButtonsENTER ButtonMENU ButtonINPUT ButtonIntelligent SensorAdjusts picture according to thesurrounding conditions.Intelligent Sensor (Except 32/37/42LG30)Adjusts picture according to the surroundingconditions ENTERCHVOLMENUINPUTCHANNEL ( , ) ButtonsVOLUME (+, -) ButtonsENTER ButtonMENU ButtonINPUT Button32/37/42LG30, 37/42/47/52LG5032/37/42/47/52LG60, 42LGXPOWER ButtonRemote Control SensorPower/Standby IndicatorIlluminates red in standby mode.Illuminates white when the set is switched on.(Can be adjusted using Power Indicator inthe OPTION menu. Gp.85)Remote Control Sensor
PREPARATION10BACK PANEL INFORMATIONPREPARATIONPlasma TV Models■Image shown may differ from your TV.12AV IN 2L/MONORAUDIOVIDEOUSB INHDMI IN 49101RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)ANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIOVIDEOAUDIO OUTOPTICAL COAXIALMONO( )AUDIOS-VIDEODIGITAL AUDIO OUTAV IN 1HDMI/DVI IN 321REMOTECONTROL IN134678295
PREPARATION11LCD TV ModelsAV IN 2L/MONORAUDIOVIDEOHDMI IN 3 USB INRGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1HDMI/DVI IN 21VIDEOMONO( )AUDIOS-VIDEO1346782995RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INANTENNA/CABLE IN12RS-232C IN(CONTROL & SERVICE)VIDEOAUDIODIGITALAUDIO OUTOPTICALAUDIO OUTAV IN 1VIDEOMONO( )AUDIOS-VIDEO21HDMI/DVI IN134678295101AV IN 2L/MONORAUDIOVIDEOUSBSERVUCE ONLYHDMI IN 3911137/42/47/52LG5032/37/42LG3012
PREPARATION12PREPARATIONAV IN 2L/MONORAUDIOVIDEOHDMI IN 4 USB IN9101■Image shown may differ from your TV.32/37/42/47/52LG60, 42LGX32/42/47/52LG70, 47LG90LCD TV Models1212RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)VIDEOAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1HDMI/DVI IN 231VIDEOMONO( )AUDIOS-VIDEO21134678295AV INL/MONORAUDIOVIDEOHDMI IN 4 USB IN9101(RGB/DVI)AUDIORGB(PC)REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUT123COMPONENT IN21VIDEOAUDIOHDMI/DVI IN RGB IN ANTENNA/CABLE IN27413611
PREPARATION13HDMI/DVI IN, HDMI INDigital Connection. Supports HD video and Digital audio. Doesn’tsupport 480i. Accepts DVI video using an adapter or HDMI toDVI cable (not included).COMPONENT INAnalog Connection. Supports HD. Uses a red, green, and blue cable for video & redand white for audio.RGB (PC)Analog PC Connection. Uses a D-sub 15 pin cable(VGA cable).AUDIO (RGB/DVI)1/8” headphone jack for analog PC audio input.REMOTE CONTROL IN PORTFor a wired remote control.RS-232C IN (CONTROL & SERVICE) PORTUsed by third party devices.ANTENNA/CABLE INConnect over-the air signals to this jack.Connect cable signals to this jack.DIGITAL AUDIO OUTDigital audio output for use with amps and hometheater systems. Includes an optical and/or coaxial connection.Note: In standby mode, these ports do not work.AUDIO OUTAnalog audio output for use with amps and hometheater systems.AV (Audio/Video) INAnalog composite connection. Supports standarddefinition video only (480i).S-VIDEOBetter quality than standard composition.Supports standard definition video only (480i).USB INPUTUsed for viewing photos and listening to MP3s.USB SERVICE ONLY or RS-232C IN (SERVICEONLY)Used for software updates.Power Cord SocketFor operation with AC power. Caution: Never attempt to operate the TV on DCpower.123456791011128
PREPARATION14PREPARATIONSTAND INSTALLATION■Image shown may differ from your TV.■When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, the prod-uct can tilt forward after the product installation). If you tighten the bolt with excessive force, the bolt can devi-ate from abrasion of the tightening part of the bolt.■You can remove the stand before installing the TV on a wall mount by performing the stand instructions inreverse. Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.Assemble the TV as shown.Fix the 4 bolts securely using the holes in theback of the TV.12Assemble the parts of the STAND BODYwith COVER BASE of the TV.23Assemble the TV as shown.3Fix the 4 bolts securely using the holes in theback of the TV.4Only 42PG25 Only 32/37/42LG30, 37/42LG50, 32/42LG70, STAND BODYCOVER BASECarefully place the TV screen side down on acushioned surface to protect the screen fromdamage.1
PREPARATION15Assemble the parts of the STAND BODYwith COVER BASE of the TV.2Assemble the TV as shown.3Fix the 4 bolts securely using the holes in theback of the TV.4Only 32/37/42LG60, 42LGXCarefully place the TV screen side down on acushioned surface to protect the screen fromdamage.132LG60 37LG60 42LG60, 42LGX(M4x16) STAND BODY STAND BODYCOVER BASESTAND BODYCOVER BASECOVER BASE(M4x20)
PREPARATION16STAND DETACHMENTPREPARATION■Image shown may differ from your TV.■Image shown may differ from your TV.LCD TV ModelsYou can remove the stand before installing the TV ona wall mount by performing the previous stand instruc-tions in reverse. After removing the stand, install theincluded protection cover over the hole for thestand.Press the PROTECTION COVER into the TV untilyou hear it click.After removing the protection paper from theprotection cover, adhere it to the TV as shown.PROTECTION COVER47/52LG50/70 47/52LG60Carefully place the TV screen side down on acushioned surface to protect the screen fromdamage.1Loose the bolts from TV.2Detach the stand from TV.2Plasma TV Models50PG25/60 60PG60
PREPARATION17VESA WALL MOUNTINGInstall your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, pleasecontact your nearest dealer.If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.We recommend that you use an LG brand wall mount when mounting the TV to a wall.GDo not install your wall mount kit while your TV is turned on. It may result in personal injury due to electricshock.CAUTIONGScrew length needed depends on the wall mountused. For further information, refer to the instruc-tions included with the mount.GStandard dimensions for wall mount kits are shownin the table.GGWhen purchasing our wall mount kit, a detailedinstallation manual and all parts necessary forassembly are provided.GGDo not use screws longer then the standard dimen-sion, as they may cause damage to the inside tothe TV.GFor wall mounts that do not comply with the VESAstandard screw specifications, the length of thescrews may differ depending on their specifica-tions.GDo not use screws that do not comply with theVESA standard screw specifications.Do not use fasten the screws too strongly, this maydamage the TV or cause the TV to a fall, leading topersonal injury. LG is not liable for these kinds ofaccidents.GLG is not liable for TV damage or personal injurywhen a non-VESA or non specified wall mount isused or the consumer fails to follow the TV installa-tion instructions.NOTE!ABProduct Model VESA Standard Screw Quantity32LG30, 32LG60, 32LG7037LG30, 37LG60, 37LG5042LG30, 42LG50, 42LG60, 42LG70, 42LGX47LG50, 47LG60, 47LG70, 47LG9052LG50, 52LG60, 52LG7042PG2550PG25, 50PG60, 50PG7060PG60, 60PG70200 * 10 0200 * 200800 * 400400 * 400600 * 400M4M6M6M6M844444LCD TVPLASMA TV
PREPARATION18CABLE MANAGEMENTPREPARATION■Image shown may differ from your TV.Plasma TV ModelsConnect the cables as necessary.To connect additional equipment, see theEXTERNAL EQUIPMENT SETUP section.Install the CABLE MANAGEMENT CLIP asshown.If your TV has the CABLE HOLDER, install itas shown and bundle the cables.12GDo not hold the CABLE MANAGEMENT CLIP when moving the TV.- If the TV is dropped, you may be injured or the product may be broken.NOTE!How to remove the CABLE MANAGEMENT CLIPGFirst, press the cable management. Hold theCABLE MANAGEMENT CLIP with bothhands and pull it upward.GSeparate CABLE MAN-AGEMENT CLIP from TVby pressing two latches.GHold the CABLE MAN-AGEMENT CLIP with bothhands and pull it upward.42PG25 50PG25, 50/60PG60, 50/60PG70CABLE MANAGEMENT CLIPCABLE HOLDER
PREPARATION19LCD TV ModelsConnect the cables as necessary.To connect additional equipment, see theEXTERNAL EQUIPMENT SETUP section.Install the CABLE MANAGEMENT CLIP asshown.CABLE MANAGEMENT CLIP12Align the hole with the tab on the CABLEMANAGEMENT CLIP.Turn the CABLE MANAGEMENT CLIP asshown.Note: This cable management clip can be bro-ken by excessive pressure.Connect the cables as necessary.To connect additional equipment, see theEXTERNAL EQUIPMENT SETUP section.12Put the cables inside the CABLE MANAGEMENTCLIP and snap it closed.332/37/42/47/52LG60, 42LGX32/37/42LG30, 37/42/47/52LG50,32/42/47/52LG70, 47LG90
PREPARATION20DESKTOP PEDESTAL INSTALLATIONPREPARATIONFor proper ventilation, allow a clearance of 4 inches on all four sides from the wall.■Image shown may differ from your TV.4 inches4 inches4 inches 4 inchesSWIVEL STANDAfter installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suityour viewing position.GEnsure adequate ventilation by following the clearance recommendations.GGDo not mount near or above any type of heat source.CAUTIONATTACHING THE TV TO A DESK (Only 32LG30/70, 42LG30/50)The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causinginjury or damaging the product. GTo prevent TV from falling over, the TV should be securely attached to the floor/wall per installationinstructions. Tipping, shaking, or rocking the machine may cause injury.WARNING1-Screw(provided as parts of the product)DeskStand
PREPARATION21SECURING THE TV TO THE WALL TO PREVENT FALLINGWe recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. ■Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. *If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately) tothe wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely.■Use a sturdy rope (not provided as parts of the product, must pur-chase separately) to tie the product. It is safer to tie the rope so itbecomes horizontal between the wall and the product.■You should purchase necessary components to prevent TV from falling off of the stand.■Image shown may differ from your TV.GUse a platform or cabinet strong enough and large enough to support the size and weight of the TV.GTo use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.NOTE!
PREPARATION22ANTENNA OR CABLE CONNECTIONPREPARATION1. Antenna (Analog or Digital)Wall Antenna Socket or Outdoor Antenna without a Cable BoxConnection.For optimum picture quality, adjust the antenna direction if needed.2. CableWallAntennaSocketOutdoorAntenna(VHF, UHF)Cable TVWall JackMulti-family Dwellings/Apartments(Connect to wall antenna socket)RF Coaxial Wire (75 ohm)RF Coaxial Wire (75 ohm)Single-family Dwellings /Houses(Connect to wall jack for outdoor antenna)Be careful not to bend the copper wirewhen connecting the antenna.Copper Wire■To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. ■If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.■If the antenna is not installed properly, contact your dealer for assistance.ANTENNA/CABLE INANTENNA/CABLE IN■To prevent damage do not connect to the power outlet until all connections are made between the devices.
EXTERNAL EQUIPMENT SETUP23EXTERNAL EQUIPMENT SETUPHD RECEIVER SETUPThis TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, ifyou do receive digital signals from a digital set-top box or other digital external device.Component Connection1. How to connectConnect the video outputs (Y, PB, PR)of the digital set-top box to the COMPONENT IN VIDEO 1 jacks onthe TV. Match the jack colors (Y = green, PB= blue, andPR= red).Connect the audio output of the digital set-top box to the COMPONENT IN AUDIO 1 jacks on the TV.212. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box. operation)■Select the Component 1 input source on the TV usingthe INPUT button on the remote control.■If connected to COMPONENT IN2 input, select theComponent 2 input source on the TV.■To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.■Image shown may differ from your TV.Y, CB/PB, CR/PRSupported ResolutionsHorizontal Vertical Frequency(KHz)Frequency(Hz)15.73 59.9415.73 60.0031.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0026.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.9467.50 60.00Resolution 720x480i720x480p1280x720p1920x1080i1920x1080pSignal480i480p720p108 0 i108 0 pComponentYesYesYesYesYesHDMINoYesYesYesYes
EXTERNAL EQUIPMENT SETUP24EXTERNAL EQUIPMENT SETUPRGB INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INRS-232(CONTROL & OPTDIGIS-VIDEOCOMPONENT IN12VIDEOLYPBPRRAUDIOY L RPBPR12(RGB/DVI)AUDIORGB(PC)REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUT123HDMI/DVI IN RGB IN ANTENNA/CABLE INCOMPONENT IN21VIDEOAUDIOYL R PBPR1232/37/42/47/52LG60, 42LGXPlasma TV, 32/37/42LG30, 37/42/47/52LG50,32/42/47/52LG70, 47LG90
EXTERNAL EQUIPMENT SETUP25HDMI ConnectionConnect the digital set-top box to HDMI/DVI IN1,2, 3, or 4 jack on the TV.No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■Select the HDMI1, HDMI2, HDMI3, or HDMI4 inputsource on the TV using the INPUT button on the remotecontrol.21HDMI-DTVHorizontal Vertical Frequency(KHz)Frequency(Hz)31.47 59.9431.50 60.0044.96 59.9445.00 60.0033.72 59.9433.75 60.0026.97 23.97627.00 24.0033.71 29.9733.75 30.0067.432 59.93967.50 60.00Resolution 720x480p1280x720p1920x1080i1920x1080p
EXTERNAL EQUIPMENT SETUP26EXTERNAL EQUIPMENT SETUPRGB INCOMPONENTA(RGRGB(PC)12VIDEOYPBPRHDMI/DVI IN 21HDMI-DTV OUTPUT1RGB INCOMPONRGB(PC)VIDEOYPBPR23HDMI/DVI IN 1HDMI-DTV OUTPUT1(RGB/DVI)AUDIORGB(PC)REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUTRGB IN ANTENNA/CABLE INCOMPONENT IN21VIDEOAUDIOHDMI/DVI IN 123HDMI-DTV OUTPUT132/37/42/47/52LG60, 42LGX32/37/42LG30, 37/42/47/52LG50 Plasma TV, 32/42/47/52LG70, 47LG90
EXTERNAL EQUIPMENT SETUP27DVI to HDMI Connection32/37/42LG30, 37/42/47/52LG50, Plasma TV- Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, or 3jack on the TV.32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90- Connect the DVI output of the digital set-top box to the HDMI/DVI IN 1, 2, 3, or 4jack on the TV.Connect the PC audio output to the AUDIO (RGB/DVI)jack on the TV.1. How to connect2. How to use■Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)■32/37/42LG30, 37/42/47/52LG50, Plasma TV- Select the HDMI1,HDMI2,orHDMI3 input source on the TV using the INPUT button on the remote control.■32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90- Select the HDMI1,HDMI2,HDMI3,orHDMI4 input source on the TV using the INPUT button on the remotecontrol.21GA DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio,so a separate audio connection is necessary.NOTE!
EXTERNAL EQUIPMENT SETUP28EXTERNAL EQUIPMENT SETUPREMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUTANTENNA/CABLE INCOMPONENT IN21VIDEOAUDIOHDMI/DVI IN 123(RGB/DVI)AUDIORGB(PC)RGB IN L RDVI-DTV OUTPUT1232/37/42/47/52LG60, 42LGXRGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL IN12R(CONTVIDEOLYPBPRRAUDIOHDMI/DVI IN 21SL RDVI-DTV OUTPUT1232/37/42LG30, 37/42/47/52LG50RGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTCONTROL(VIDEOLYPBPRRAUDIOAV IN 12321HDMI/DVI IN 1L RDVI-DTV OUTPUT1Plasma TV, 32/42/47/52LG70, 47LG902
EXTERNAL EQUIPMENT SETUP29DVD SETUPComponent ConnectionComponent Input portsTo get better picture quality, connect a DVD player to the component input ports as shown below.Component ports on the TVYPBPRVideo output ports on DVD playerYYYYPBB-YCbPbPRR-YCrPrConnect the video outputs (Y, PB, PR)of the DVD to theCOMPONENT IN VIDEO1 jacks on the TV.Match the jack colors (Y = green, PB= blue, and PR= red).Connect the audio outputs of the DVD to the COMPONENT IN AUDIO1 jacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the Component 1 input source on the TV usingthe INPUT button on the remote control.■If connected to COMPONENT IN 2 input, select theComponent 2 input source on the TV.■Refer to the DVD player's manual for operating instructions.21
EXTERNAL EQUIPMENT SETUP30EXTERNAL EQUIPMENT SETUPRGB INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL INRS-232C I(CONTROL & SEROPTICADIGITAS-VIDEOCOMPONENT IN12VIDEOLYPBPRRAUDIOY L RPBPR1 2(RGB/DVI)AUDIORGB(PC)REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUT1 2 3HDMI/DVI IN RGB IN ANTENNA/CABLE INCOMPONENT IN21VIDEOAUDIOYL R PBPR1232/37/42/47/52LG60, 42LGXPlasma TV, 32/37/42LG30, 37/42/47/52LG50,32/42/47/52LG70, 47LG90
EXTERNAL EQUIPMENT SETUP31S-Video Connection (Except 32/37/42/47/52LG60, 42LGX)NUDIOB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)LRAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO LR(MONO)AUDIOS-VIDEOL RS-VIDEOAUDIO12Connect the S-VIDEO output of the DVD to theS -VIDEO input on the TV.Connect the audio outputs of the DVD to the AUDIOinput jacks on the TV.1. How to connect2. How to use■Turn on the DVD player, insert a DVD.■Select the AV1 input source on the TV using the INPUTbutton on the remote control. ■Refer to the DVD player's manual for operating instructions.21
EXTERNAL EQUIPMENT SETUP32EXTERNAL EQUIPMENT SETUPHDMI ConnectionConnect the HDMI output of the DVD to theHDMI/DVI IN1, 2, 3 or 4jack on the TV.No separate audio connection is necessary.HDMI supports both audio and video.1. How to connect2. How to use■Select the HDMI1, HDMI2, HDMI3, or HDMI4 inputsource on the TV using the INPUT button on the remotecontrol.■Refer to the DVD player's manual for operating instructions.21COMPONENT INUO(RGB/DRGB(PC)12VIDEOLYPBPRAHDMI/DVI IN 21HDMI-DVD OUTPUT1(RGB/DVI)AUDIORGB(PC)REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUTRGB IN ANTENNA/CABLE INCOMPONENT IN21VIDEOAUDIOHDMI/DVI IN 123HDMI-DVD OUTPUT132/37/42LG30, 37/42/47/52LG5032/37/42/47/52LG60, 42LGXRGB INCOMPONENT(RRGB(PC)VIDEOYPBPR2321HDMI/DVI IN 1HDMI-DVD OUTPUT1Plasma TV, 32/42/47/52LG70, 47LG90
EXTERNAL EQUIPMENT SETUP33VCR SETUPAntenna Connection■To avoid picture noise (interference), leave an adequate distance between the VCR and TV.■Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long periodof time (Plasma TV models only). If the 4:3 picture format is used; the fixed images on the sides of the screenmay remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty.ANTENNA/CABLE INE)COAXIALUDIO OUTAUDIO OUTAV IN 1EO L R(MONO)AUDIOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTWall JackAntenna12REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICCOAXANTENNA/CABLE INCOMPAUDIOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTWall JackAntenna12Connect the RF antenna out socket of theVCR to the ANTENNA/CABLE IN sock-et on the TV.Connect the antenna cable to the RFantenna in socket of the VCR.1. How to connect2. How to use■Set VCR output switch to 3 or 4 and thentune TV to the same channel number.■Insert a video tape into the VCR and pressPLAY on the VCR. (Refer to the VCR owner’smanual.)21Plasma TV, 32/37/42LG30, 37/42/47/52LG50,32/42/47/52LG70, 47LG9032/37/42/47/52LG60, 42LGX
EXTERNAL EQUIPMENT SETUP34EXTERNAL EQUIPMENT SETUPL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUTAV INL/MONORAUDIOVIDEOHDMI IN 4 USB IN1Composite (RCA) ConnectionGIf you have a mono VCR, connect the audio cable fromthe VCR to the AUDIO L/MONO jack of the TV.NOTE!NT INAUDIO(RGB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)LRAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUT1Plasma TV, 32/37/42LG30,37/42/47/52LG50,32/42/47/52LG70, 47LG9032/37/42/47/52LG60, 42LGXConnect the AUDIO/VIDEO jacks between TV andVCR. Match the jack colors (Video = yellow, Audio Left= white, and Audio Right = red)1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select the AV1 input source on the TV using the INPUTbutton on the remote control.■If connected to AV IN2, select AV2 input source on the TV.1
EXTERNAL EQUIPMENT SETUP35GDo not connect to both Video and S-Video at the sametime. In the event that you connect both Video and theS-Video cables, only the S-Video will work.CAUTIONGS-Video provides better quality than composite. Use itwhen available.NOTE!S-Video Connection (Except 32/37/42/47/52LG60, 42LGX)NT INAUDIO(RGB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)LRAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO LR(MONO)AUDIOS-VIDEOL RS-VIDEO VIDEOOUTPUTSWITCHANT INANT OUT12Connect the S-VIDEO output of the VCR to theS-VIDEO input on the TV.Connect the audio outputs of the VCR to the AUDIOinput jacks on the TV.1. How to connect2. How to use■Insert a video tape into the VCR and press PLAY on the VCR.(Refer to the VCR owner’s manual.)■Select the AV1 input source on the TV using the INPUTbutton on the remote control.21
EXTERNAL EQUIPMENT SETUP36OTHER A/V SOURCE SETUPEXTERNAL EQUIPMENT SETUPL/MONORAUDIOVIDEOHDMI IN 3 USB INL RVIDEOCamcorderVideo Game SetConnect the AUDIO/VIDEO jacksbetween TV and external equipment.Match the jack colors.(Video = yellow, Audio Left = white, andAudio Right = red)1. How to connect2. How to use■Select the AV2 input source on the TV usingthe INPUT button on the remote control.■If connected to AV IN1 input, select the AV1input source on the TV.■Operate the corresponding external equipment.11
EXTERNAL EQUIPMENT SETUP37PC SETUPThis TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. VGA (D-Sub 15 pin) ConnectionConnect the VGA output of the PC to the RGB (P C) jack on the TV.Connect the PC audio output to the AUDIO (RGB/DVI)jack on the TV.1. How to connect2. How to use■Turn on the PC and the TV.■Select the RGB-PC input source on the TV using the INPUT button on the remote control.21COMPONENT INREMOTECONTROL IN12(COVIDEOLYPBPRRAUDIONRGB INAUDIO(RGB/DVI)RGB(PC)RGB OUTPUT AUDIO12REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUT123HDMI/DANTENNA/CABLE INCOMPONENT INVIDEOAUDIO(RGB/DVI)AUDIORGB(PC)RGB IN RGB OUTPUT AUDIO12Plasma TV, 32/37/42LG30, 37/42/47/52LG50,32/42/47/52LG70, 47LG90 32/37/42/47/52LG60, 42LGX
EXTERNAL EQUIPMENT SETUP38EXTERNAL EQUIPMENT SETUPG32/37/42LG30, 42/50PG25: To get the the bestpicture quality, adjust the PC graphics card to1360x768.G37/42/47/52LG50, 32/37/42/47/52LG60,32/42/47/52LG70, 42LGX, 47LG90,50/60PG60, 50/60PG70: To get the the bestpicture quality, adjust the PC graphics card to1920x1080.GDepending on the graphics card, DOS mode maynot work if a HDMI to DVI Cable is in use.GIn PC mode, there may be noise associated withthe resolution, vertical pattern, contrast or bright-ness. If noise is present, change the PC output toanother resolution, change the refresh rate toanother rate or adjust the brightness and contraston the PICTURE menu until the picture is clear.GAvoid keeping a fixed image on the screen for along period of time. The fixed image could becomepermanently imprinted on the screen.GThe synchronization input form for Horizontal andVertical frequencies is separate.NOTES!DVI to HDMI Connection32/37/42LG30, 37/42/47/52LG50, Plasma TV- Connect the DVI output of the PC to the HDMI/DVI IN 1, 2, or 3 jack on the TV.32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90- Connect the DVI output of the PC to the HDMI/DVI IN 1, 2, 3, or 4 jack on the TV.Connect the PC audio output to the AUDIO (RGB/DVI) jack on the TV.1. How to connect■Turn on the PC and the TV.■32/37/42LG30, 37/42/47/52LG50, Plasma TV- Select the HDMI1,HDMI2,orHDMI3 input source on the TV using the INPUT button on the remote control.■32/37/42/47/52LG60, 32/42/47/52LG70, 42LGX, 47LG90- Select the HDMI1,HDMI2,HDMI3,orHDMI4 input source on the TV using the INPUT button on the remotecontrol.2. How to use21
EXTERNAL EQUIPMENT SETUP39REMOTECONTROL INRS-232C IN(SERVICE ONLY)OPTICALCOAXIALDIGITAL AUDIO OUTANTENNA/CABLE INCOMPONENT IN21VIDEOAUDIOHDMI/DVI IN 123(RGB/DVI)AUDIORGB(PC)RGB IN DVI-PC OUTPUT AUDIO1232/37/42/47/52LG60, 42LGXRGB INCOMPONENT INAUDIO(RGB/DVI)RGB(PC)REMOTECONTROL IN(COVIDEOLYPBPRRAUDIOAV IN 12321HDMI/DVI IN 1DVI-PC OUTPUT AUDIOCOMPONENT INREMOTECONTROL IN12R(CONTVIDEOLYPBPRRAUDIOHDMI/DVI IN 21SRGB INAUDIO(RGB/DVI)RGB(PC)DVI-PC OUTPUT AUDIO12232/37/42LG30, 37/42/47/52LG501Plasma TV, 32/42/47/52LG70, 47LG90
EXTERNAL EQUIPMENT SETUP40EXTERNAL EQUIPMENT SETUPHorizontal Vertical Frequency(KHz)Frequency(Hz)31.469 70.0831.469 70.0831.469 59.9437.879 60.3148.363 60.0047.776 59.8747.720 59.79947.130 59.65Resolution 720x4001360x768640x350640x480800x6001024x7681280x7681366x768Supported Display Specifications (RGB-PC, HDMI-PC)For 32/37/42LG30For 37/42/47/52LG50, 32/37/42/47/52LG60,32/42/47/52LG70, 42LGX, 47LG90* Only RGB-PC mode GDepending on the graphics card, some resolution settings may not allow the image to be positioned on thescreen properly.GIf there are overscan in HDMI-PC 1920x1080, change aspect ratio to Just scan.NOTE!Resolution 720x4001360x768640x350640x480800x6001024x7681280x10241600x12001920x1080RGB-PC1920x1080HDMI-PC1280x768Horizontal Vertical Frequency(KHz)Frequency(Hz)31.468 70.0931.469 70.0831.469 59.9437.500 75.0037.861 72.8035.156 56.2537.879 60.3146.875 75.0048.077 72.1848.363 60.0056.476 70.0660.023 75.0247.776 59.8760.289 74.89363.981 60.0279.976 75.02547.712 60.01575.00 60.0066.587 59.93467.5 60.00* Only RGB-PC mode
EXTERNAL EQUIPMENT SETUP41Resolution 720x4001360x768640x350640x480800x6001024x7681280x10241600x12001920x10801280x768Horizontal Vertical Frequency(KHz)Frequency(Hz)31.468 70.0931.469 70.0831.469 59.9437.500 75.0037.861 72.8035.156 56.2537.879 60.3146.875 75.0048.077 72.1848.363 60.0056.476 70.0660.023 75.0247.776 59.8760.289 74.89363.981 60.0279.976 75.02547.712 60.01575.00 60.0066.587 59.934For 42/50PG25, 50/60PG60, 50/60PG70* Only RGB-PC mode
EXTERNAL EQUIPMENT SETUP42EXTERNAL EQUIPMENT SETUPScreen Setup for PC modeSelecting ResolutionYou can choose the resolution in RGB-PC mode. The Position, Phase, and Size can also be adjusted.Select PICTURE.Select Screen (RGB-PC).Select Resolution.Select the desired resolution.1024 x 7681280 x 7681360 x 7681366 x 768Auto config.ResolutionGPositionSizePhaseResetSCREENMovePrev.MENU1MENU342ENTERENTERENTER5ENTEREnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRG Only for32/37/42LG30
EXTERNAL EQUIPMENT SETUP43Auto ConfigureAutomatically adjusts picture position and minimizes image instability. After adjustment, if the image is stillnot correct, try using the manual settings or a different resolution or refresh rate on the PC.Select Screen (RGB-PC).Select Auto config..Auto config. GResolutionPositionSizePhaseResetSCREENMovePrev.MENUTo Set32ENTERENTERSelect Yes.4ENTERStart Auto Configuration.5ENTERSelect PICTURE.1MENU• If the position of the image is still notcorrect, try Auto adjustment again.• If picture needs to be adjusted againafter Auto adjustment in RGB-PC, youcan adjust the P o si tion, Size orPhase.EnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRGYes No
EXTERNAL EQUIPMENT SETUP44EXTERNAL EQUIPMENT SETUPAdjustment for screen Position, Size, and PhaseIf the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picturephase manually.This feature operates only in RGB-PC mode.Select Position, Size, or Phase.Make appropriate adjustments.Auto config.ResolutionPositionGSizePhaseResetGFDESCREENMovePrev.MENU3ENTER4ENTER■Position: This function is to adjust pic-ture to left/right and up/down as youprefer. ■Si ze: This function is to minimize anyvertical bars or stripes visible on thescreen background. And the horizontalscreen size will also change.■Phase: This function allows you toremove any horizontal noise and clear orsharpen the image of characters.Select PICTURE.Select Screen (RGB-PC).1MENU2ENTER5ENTEREnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRG
EXTERNAL EQUIPMENT SETUP45Screen Reset (Reset to original factory values)Returns Position, Size, and Phase to the default factory settings.This feature operates only in RGB-PC mode.Auto config.PositionResolutionSizePhaseResetGSCREENMovePrev.MENUTo SetSelect Reset.3ENTERSelect PICTURE.Select Screen (RGB-PC).1MENU2ENTERSelect Yes.4ENTER5ENTEREnterMovePICTUREE• Brightness 50• Sharpness 60• Color 60• Tint 0• Advanced Control• ResetScreen (RGB-PC)TruMotion DemoRGYes No
EXTERNAL EQUIPMENT SETUP46USB CONNECTION(Except 32/37/42LG30)EXTERNAL EQUIPMENT SETUPAV IN 2L/MONORAUDIOVIDEOHDMI IN 3 USB INConnect the USB device to the USB I N jack on the sideof TV. 1. How to connect12. How to use■After connecting the USB I N jack, you use the USB func-tion. (Gp.64)1ori.e)
EXTERNAL EQUIPMENT SETUP47AUDIO OUT CONNECTIONSend the TV’s audio to external audio equipment via the Audio Output port.RS-232C IN(CONTROL & SERVICE)RUDIOAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEOL RAUDIO1NUDIOB/DVI)REMOTECONTROL INANTENNA/CABLE INRS-232C IN(CONTROL & SERVICE)LRAUDIOOPTICAL COAXIALDIGITAL AUDIO OUTAUDIO OUTAV IN 1VIDEO L R(MONO)AUDIOS-VIDEO12GWhen connecting with external audio equipments, such asamplifiers or speakers, you can turn the TV speakers off inthe menu. (G p.93)NOTE!GDo not look into the optical output port. Looking at thelaser beam may damage your vision.GBlock the SPDIF out (optical/coaxial) about the contentswith ACP(Audio Copy Protection) function.CAUTIONConnect one end of the optical or coaxial cable to theTV’s OPTICAL or COAXIAL (Except 32/37/42LG30)port of DIGITAL AUDIO OUT.Connect the other end of the optical or coaxial cable tothe digital audio input on the audio equipment.Set the “TV Speaker option - Off” in the AUDIO menu. (Gp.93). See the external audio equipment instruction manu-al for operation.1. How to connect231Connect audio outputs to the TV’s AUDIO OUT jacks.Set the “TV Speaker option - Off” in the AUDIO menu.(Gp.93). See the external audio equipment instructionmanual for operation.1. How to connect21Analog (Except 32/37/42/47/52LG60, 42LGX)Digital
WATCHING TV / CHANNEL CONTROL48REMOTE CONTROL FUNCTIONSWATCHING TV / CHANNEL CONTROLWhen using the remote control, aim it at the remote control sensor on the TV.INPUTFAVMUTETVSTBPOWERQ. MENU MENUAV MODERETURNENTERVOL CH1234567809FLASHBKPAGEDVDVCRTV/STB/DVD/VCRPOWERQ.MENUMENUINPUTVOLUME UP/DOWNFAVMUTECHANNELUP/DOWNPAGEUP/DOWN— (DASH)FLASHBKSelect the remote operating mode: TV, STB, DVD, or VCR. Turns your TV or any other programmed equipment on oroff, depending on the mode.Select the desired quick menu source. Gp.51Displays the main menu.Clear all on-screen displays and return to TV viewing fromany menu.External input modes rotate in regular sequence.Increase/decrease the sound level.Scroll through the programmed Favorite channels. Gp.51Switch the sound on or off. Gp.50Select available channels.Move from one full set of screen information to the next one.Used to enter a program number for multiple program channels such as 2-1, 2-2, etc.Tune to the last channel viewed.Control video cassette recorders or DVD players.Control USB menu (PHOTO LIST and MUSIC LIST.)Control the SIMPLINK compatible devices.NUMBER buttonVCR/DVD, USB,SIMPLINK Control buttons
WATCHING TV / CHANNEL CONTROL49Installing Batteries■Open the battery compartment cover on the back side and installthe batteries matching correct polarity (+with +,-with -).■Install two 1.5V AAA batteries. Don’t mix old or used batteries withnew ones.■Close cover.THUMBSTICK(Up/Down/LeftRight/ENTER)RETURNSIMPLINKAV MODENavigate the on-screen menus and adjust the system settings to your preference.Allows the user to move return one step in an interactive application or other user interactionfunction.See a list of AV devices connected to TV.When you toggle this button, the SIMPLINK menu appears at the screen. Gp.62-63It helps you select and set images and sounds. Gp.61
WATCHING TV / CHANNEL CONTROL50TURNING ON THE TVWATCHING TV / CHANNEL CONTROLNOTE!GIf you intend to be away on vacation, disconnect the power plug from the wall power outlet.First, connect power cord correctly. At this moment, the TV switches to standby mode.■In standby mode to turn TV on, press the , INPUT,CH (DE or )button on the TV or press the POWER, INPUT, CH( or ), Number(0~9) button on the remote control.Select the viewing source by using the INPUT button on the remote control.■This TV is programmed to remember which power state it was last set to,even if the power cord is out.When finished using the TV, press the POWER button on the remote control.The TV reverts to standby mode.123Press the CH ( or )or NUMBER buttons to select a channel number.1VOLUME ADJUSTMENTCHANNEL SELECTIONPress the VOL (+ or -) button to adjust the volume.If you want to switch the sound off, press the MUTE button. You can cancel the Mute function by pressing the MUTE or VOL (+ or -)button.Adjust the volume to suit your personal preference.123

Navigation menu