LG Electronics USA 42LG70UG LCD TV/MONITOR User Manual SAC30708020 Edit1 en 6

LG Electronics USA LCD TV/MONITOR SAC30708020 Edit1 en 6

Contents

User manual 1 of 2

Download: LG Electronics USA 42LG70UG LCD TV/MONITOR User Manual SAC30708020 Edit1 en 6
Mirror Download [FCC.gov]LG Electronics USA 42LG70UG LCD TV/MONITOR User Manual SAC30708020 Edit1 en 6
Document ID958757
Application IDmPGKY6BBXWvtZ7MP77CL9A==
Document DescriptionUser manual 1 of 2
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize321.75kB (4021906 bits)
Date Submitted2008-06-20 00:00:00
Date Available2008-06-20 00:00:00
Creation Date2008-06-18 15:22:58
Producing SoftwareAcrobat Distiller 4.0 for Macintosh
Document Lastmod2008-06-18 15:23:14
Document TitleSAC30708020-Edit1-en_6
Document Creator3.3: LaserWriter 8 Z1-8.7.1
Document Author: sun

LCD TV PLASMA TV
OWNER’S MANUAL
LCD TV MODELS
PLASMA TV MODELS
32LG30
37LG30
42LG30
42LGX
37LG50
42LG50
47LG50
52LG50
42PG25
50PG25
32LG60
37LG60
42LG60
47LG60
52LG60
32LG70
42LG70
47LG70
52LG70
50PG60
60PG60
50PG70
60PG70
47LG90
ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency (EPA).
As an ENERGY STAR Partner
LG Electronics USA, Inc.
has determined that this
product meets the ENERGY
STAR guidelines for energy
efficiency.
Please read this manual carefully before operating
your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.
P/NO : SAC30708020 (0805-REV06)
www.lgusa.com / www.lg.ca
WARNING / CAUTION
WARNING / CAUTION
To prevent fire or shock hazards, do not expose
this product to rain or moisture.
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING/CAUTION
TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.
FCC NOTICE
Class B digital device
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Any changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
CAUTION
Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
Only use attachments/accessories specified by
the manufacturer.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
Unplug this apparatus during lighting storms
or when unused for long periods of time.
10
Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers)that produce
heat.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a
third grounding prong, The wide blade or the
third prong are provided for your safety. If the
provided plug does not fit into your outlet,
consult an electrician for replacement of the
obsolete outlet.
SAFETY INSTRUCTIONS
11
Never touch this apparatus or antenna during
a thunder or lighting storm.
12
When mounting a TV on the wall, make sure
not to install the TV by the hanging power and
signal cables on the back of the TV.
13
Do not allow an impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.
14
CAUTION concerning the Power Cord:
It is recommend that appliances be placed
upon a dedicated circuit; that is, a single
outlet circuit which powers only that appliance
and has no additional outlets or branch
circuits. Check the specification page of this
owner's manual to be certain.
Do not connect too many appliances to the
same AC power outlet as this could result in
fire or electric shock.
Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of
the appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not make the TV with the power cord
plugged in. Do not use a damaged or loose
power cord. Be sure do grasp the plug when
unplugging the power cord. Do not pull on the
power cord to unplug the TV.
15
WARNING - To reduce the risk of fire or electrical
shock, do not expose this product to rain,
moisture or other liquids. Do not touch the TV
with wet hands. Do not install this product
near flammable objects such as gasoline or
candles or expose the TV to direct air
conditioning.
16
Do not expose to dripping or splashing and do
not place objects filled with liquids, such as
vases, cups, etc. on or over the apparatus (e.g.
on shelves above the unit).
17
GROUNDING
Ensure that you connect the earth ground wire
to prevent possible electric shock (i.e. a TV
with a three-prong grounded AC plug must be
connected to a three-prong grounded AC outlet). If grounding methods are not possible,
have a qualified electrician install a separate
circuit breaker.
Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas
pipes.
Short-circuit
Breaker
Power
Supply
18
DISCONNECTING DEVICE FROM MAINS
Mains plug is the disconnecting device. The
plug must remain readily operable.
19
Keep the product away from direct sunlight.
20
ANTENNAS
Outdoor antenna grounding
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead power lines or other electric light or
power circuits, or where it can come in contact
with such power lines or circuits as death or
serious injury can occur.
Be sure the antenna system is grounded so as
to provide some protection against voltage
surges and built-up static charges.
Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information with
respect to proper grounding of the mast and
supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding
electrode.
Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70
Ground Clamp
22
Moving
Make sure the product is turned off,
unplugged and all cables have been removed. It
may take 2 or more people to carry larger TVs.
Do not press against or put stress on the front
panel of the TV.
23
Ventilation
Install your TV where there is proper ventilation. Do not install in a confined space such as
a bookcase. Do not cover the product with
cloth or other materials (e.g.) plastic while
plugged in. Do not install in excessively dusty
places.
24
If you smell smoke or other odors coming from
the TV or hear strange sounds, unplug the
power cord contact an authorized service center.
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Electric Service
Equipment
Grounding Conductor
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System (NEC
Art 250, Part H)
NEC: National Electrical Code
21
Cleaning
When cleaning, unplug the power cord and
scrub gently with a soft cloth to prevent
scratching. Do not spray water or other liquids
directly on the TV as electric shock may occur.
Do not clean with chemicals such as alcohol,
thinners or benzene.
CONTENTS
WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . A
SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PREPARATION
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Attaching the TV to a Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Securing the TV to the wall to prevent falling when
the TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 22
EXTERNAL EQUIPMENT SETUP
HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Audio Out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
WATCHING TV / CHANNEL CONTROL
Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Turning On the TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Channel Setup
- Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
- Add / Delete Channel (Manual Tuning) . . . . . . 57
- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
USB
Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
PICTURE CONTROL
Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 72
Preset Picture Settings
- Picture Mode - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
- Color Tone - Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Manual Picture Adjustment
- Picture Mode - User Mode . . . . . . . . . . . . . . . . . . . . . . . . 76
- Picture Mode - Expert Control . . . . . . . . . . . . . . . . . . 77
Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 78
Advanced Control - Black (Darkness) Level . . . . . . . 79
Advanced Control - Eye Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Advanced Control - Real Cinema/Film Mode . . . . . 81
Advanced Control - TruMotion . . . . . . . . . . . . . . . . . . . . . . . . 82
TruMotion Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Local Dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Local Dimming Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Image Sticking Minimization (ISM) Method . . . . . . 86
Power Saving Picture Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
SOUND & LANGUAGE CONTROL
APPENDIX
Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 88
Preset Sound Settings (Sound Mode) . . . . . . . . . . . . . . 89
Sound Setting Adjustment - User Mode . . . . . . . . . . . 90
Clear Voice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Stereo/SAP Broadcast Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
On-Screen Menus Language Selection . . . . . . . . . . . . . . 97
Caption Mode
- Analog Broadcasting System Captions . . . . . . . 98
- Digital Broadcasting System Captions . . . . . . . . 99
- Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Programming the Remote Control . . . . . . . . . . . . . . . . . . 124
IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
External Control Through RS-232C . . . . . . . . . . . . . . . . .129
Open Source License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
TIME SETTING
Clock Setting
- Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
- Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
PARENTAL CONTROL / RATINGS
Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
FEATURE OF THIS TV
is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.
Manufactured under license from Dolby Laboratories.
“Dolby “and the double-D symbol are trademarks of
Dolby Laboratories.
THX (Thomlinson Holman’s Experiment) is the audio
and video certification standard of THX established
by George Lucas, who directed the movie Star Wars,
and Thomlinson.
This is the product to be certified in THX display area
and guarantees screen quality that exceeds the display
standard specification in both hardware and software.
FOR LCD TV
■
If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is
nothing wrong with TV.
■ Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they
have no adverse effect on the monitor's performance.
■ Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce
some temporary distortion effects on the screen.
On Disposal (Only Hg lamp used LCD TV)
The fluorescent lamp used in this product contains a small amount of mercury. Do not dispose of this product with
general household waste. Disposal of this product must be carried out in accordance to the regulations of your local
authority.
PREPARATION
ACCESSORIES
TV
PO
ST
Q.
MEN B
MEN
RE
TU
RN
AV
VO
FA
CH
MU
TE
ER
DV
MO
DE
VC
IN R
PU
EN
TE
FLASH
BK
1.5V 1.5V
Copyright© 2007 LGE,
All Rights Reserved.
Owner’s Manual
Remote Control,
Batteries
CD Manual
PREPARATION
Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the
dealer where you purchased the TV.
The accessories included may differ from the images below.
Power Cord
Option Extras
* Wipe spots on the exterior only with
the polishing cloth.
* Do not wipe roughly when removing
Polishing Cloth
stain. Excessive pressure may cause
(This feature is not available
scratch or discoloration.
for all models.)
D-sub 15 pin Cable
When using the VGA (D-sub 15 pin
cable) PC connection, the user
must use shielded signal interface
cables with ferrite cores to maintain
standards compliance.
For Plasma TV models
(Only 50PG25,
50/60PG60, 50/60PG70)
(Only 42PG25)
x4
Bolts for stand assembly
(Refer to P.13)
Cable Holder
Cable Management Clip
Protection Cover
For LCD TV models
32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90
(Only 32/37/42LG30, 37/42LG50,
32/42LG70)
(Only 32LG30/70,
42LG30/50)
or
x4
x4
Bolts for stand assembly
(Refer to P.16)
Screw for stand fixing
(Refer to P.20)
Protection Cover
32/37/42/47/52LG60, 42LGX
(Only 42LG60, 42LGX)
(Only 32/37LG60)
or
32LG60: 3EA
37LG60: 4EA
4EA
2EA
1EA
4EA
Protection Cover
Bolts for stand assembly
(Refer to P.14)
Cable Management
Clip
PREPARATION
FRONT PANEL INFORMATION
■
Image shown may differ from your TV.
■
NOTE: If your TV has a protection tape attached, remove the tape.
And then wipe the TV with a cloth (If a polishing cloth is included with your TV, use it).
PREPARATION
Plasma TV Models
Remote Control Sensor
POWER Button
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the TV is switched on.
MENU
INPUT
INPUT
INPUT
MENU
VOL
ENTER
MENU
MENU
Button
INPUT
Button
VOL
ENTER
VOL
ENTER
CH
CH
ENTER
Button
CH
VOLUME
(-, +) Buttons
CHANNEL
(E,D)Buttons
LCD TV Models
32/42/47/52LG70, 47LG90
CH
Intelligent Sensor
Adjusts picture according to the surrounding
conditions
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using P o w e r I n d i c a t o r in
the OPTION menu. G p.85)
Remote Control Sensor
POWER Button
VOL
CHANNEL (
Buttons
VOLUME (+, -)
Buttons
ENTER
ENTER Button
MENU
INPUT
MENU Button
INPUT Button
LCD TV Models
CH
Intelligent Sensor (Except 32/37/42LG30)
Adjusts picture according to the surrounding
conditions
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates blue when the set is switched on.
(Can be adjusted using P o w e r I n d i c a t o r in
the OPTION menu. G p.85)
VOL
CHANNEL (
Buttons
PREPARATION
32/37/42LG30, 37/42/47/52LG50
VOLUME (+, -)
Buttons
ENTER
ENTER Button
MENU
MENU Button
INPUT
INPUT Button
Remote Control Sensor
POWER Button
32/37/42/47/52LG60, 42LGX
CH
Intelligent Sensor
Adjusts picture according to the
surrounding conditions.
POWER Button
Remote Control Sensor
Power/Standby Indicator
Illuminates red in standby mode.
Illuminates white when the set is switched on.
(Can be adjusted using P o w e r I n d i c a t o r in
the OPTION menu. G p.85)
VOL
CHANNEL (
Buttons
VOLUME (+, -)
Buttons
ENTER Button
ENTER
MENU Button
MENU
INPUT Button
INPUT
PREPARATION
■
BACK PANEL INFORMATION
Image shown may differ from your TV.
Plasma TV Models
HDMI IN 4
USB IN
ANTENNA/
CABLE IN
RGB IN
HDMI/DVI IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
DIGITAL AUDIO OUT
OPTICAL COAXIAL
AUDIO
VIDEO
AUDIO
VIDEO
HDMI/DVI IN, HDMI IN
Digital Connection.
Supports HD video and Digital audio. Doesn’t
support 480i.
Accepts DVI video using an adapter or HDMI to
DVI cable (not included).
COMPONENT IN
Analog Connection.
Supports HD.
Uses a red, green, and blue cable for video & red
and white for audio.
REMOTE CONTROL IN PORT
For a wired remote control.
RS-232C IN (CONTROL & SERVICE) PORT
Used by third party devices.
10
RGB (PC)
Analog PC Connection. Uses a D-sub 15 pin cable
(VGA cable).
AUDIO (RGB/DVI)
1/8” headphone jack for analog PC audio input.
ANTENNA/CABLE IN
Connect over-the air signals to this jack.
Connect cable signals to this jack.
(MONO)
10
AV IN 2
AUDIO OUT
AV IN 1
S-VIDEO
RS-232C IN
(CONTROL & SERVICE)
COMPONENT IN
VIDEO L/MONO AUDIO R
PREPARATION
12
DIGITAL AUDIO OUT
Digital audio output for use with amps and home
theater systems.
Includes an optical and/or coaxial connection.
Note: In standby mode, these ports do not work.
AUDIO OUT
Analog audio output for use with amps and home
theater systems.
AV (Audio/Video) IN
Analog composite connection.
Supports standard
definition video only (480i).
S-VIDEO
Better quality than standard composition.
Supports standard definition video only (480i).
10
USB INPUT
Used for viewing photos and listening to MP3s.
11
USB SERVICE ONLY or RS-232C IN (SERVICE
ONLY)
Used for software updates.
12
Power Cord Socket
For operation with AC power.
Caution: Never attempt to operate the TV on DC
power.
R
PREPARATION
LCD TV Models
12
ANTENNA/
CABLE IN
USB
SERVUCE ONLY
32/37/42LG30
DIGITAL
AUDIO OUT
OPTICAL
HDMI/DVI IN
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AUDIO
VIDEO
S-VIDEO VIDEO
(MONO)
AUDIO
AV IN 1
COMPONENT IN
VIDEO L/MONO AUDIO R
REMOTE
CONTROL IN
AUDIO
(RGB/DVI)
RGB(PC)
HDMI IN 3
RGB IN
11
AV IN 2
ANTENNA/
CABLE IN
USB IN
37/42/47/52LG50, 32LG70
10
REMOTE
CONTROL IN
HDMI/DVI IN
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AUDIO
VIDEO
COMPONENT IN
AV IN 1
OPTICAL
S-VIDEO VIDEO
(MONO)
AUDIO
VIDEO L/MONO AUDIO R
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
RGB(PC)
HDMI IN 3
RGB IN
AV IN 2
11
R
PREPARATION
■
Image shown may differ from your TV.
LCD TV Models
42/47/52LG70, 47LG90
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
OPTICAL
COAXIAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AV IN 1
AUDIO
VIDEO
COMPONENT IN
S-VIDEO VIDEO
(MONO)
AUDIO
VIDEO L/MONO AUDIO R
HDMI/DVI IN
HDMI IN 4
RGB IN
10
USB IN
PREPARATION
12
AV IN 2
12
(RGB/DVI)
COAXIAL
OPTICAL
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
12
RGB(PC)
USB IN
HDMI IN 4
DIGITAL
AUDIO OUT
AUDIO
HDMI/DVI IN
RGB IN
VIDEO L/MONO AUDIO R
11
VIDEO
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
AV IN
10
STAND INSTRUCTION
■
Image shown may differ from your TV.
Plasma TV models
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Loose the bolts from TV.
PREPARATION
INSTALLATION (Only 42PG25)
Assemble the TV as shown.
42PG25
Fix the 4 bolts securely using the holes in the
back of the TV.
50PG25/60/70
60PG60/70
Detach the stand from TV.
PROTECTION COVER
! NOTE
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
After removing the stand, install the included
p r o t e c t i o n c o v e r over the hole for the stand.
Press the P R O T E C T I O N C O V E R into the TV
until you hear it click.
13
PREPARATION
32/37/42/47/52LG60, 42LGX
■
Image shown may differ from your TV.
PREPARATION
INSTALLATION (Only 32/37/42LG60, 42LGX)
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
32LG60
37LG60
42LG60, 42LGX
STAND BODY
STAND BODY
STAND BODY
COVER BASE
COVER BASE
Assemble the TV as shown.
Fix the 4 bolts securely using the holes in the
back of the TV.
! NOTE
14
When assembling the desk type stand, make sure the
bolt is fully tightened (If not tightened fully, the TV
can tilt forward after the product installation). Do not
over tighten.
COVER BASE
1
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Loose the bolts from TV.
Detach the stand from TV.
PROTECTION COVER
After removing the stand, install the included p r ot e c t i o n c o v e r over the hole for the stand.
PREPARATION
DETACHMENT
After removing the protection paper from the
protection cover, adhere it to the TV as shown.
15
PREPARATION
32/37/42LG30, 37/42/47/52LG50, 32/42/47/52LG70, 47LG90
■
Image shown may differ from your TV.
PREPARATION
INSTALLATION
(Only 32/37/42LG30, 37/42LG50, 32/42LG70)
Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.
Assemble the parts of the S T A N D B O D Y
with C O V E R B A S E of the TV.
DETACHMENT
Carefully place the TV screen side down on a
cushioned surface to protect the screen from
damage.
Loose the bolts from TV.
Detach the stand from TV.
STAND BODY
COVER BASE
Assemble the TV as shown.
PROTECTION COVER
Fix the 4 bolts securely using the holes in the
back of the TV.
! NOTE
16
When assembling the desk type stand, make sure
the bolt is fully tightened (If not tightened fully,
the TV can tilt forward after the product installation). Do not over tighten.
After removing the stand, install the included
p r o t e c t i o n c o v e r over the hole for the stand.
Press the P R O T E C T I O N C O V E R into the TV
until you hear it click.
VESA WALL MOUNTING
PREPARATION
Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please
contact your nearest dealer.
If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.
We recommend that you use an LG brand wall mount when mounting the TV to a wall.
LG recommends that wall mounting be performed by a qualified professional installer.
Product
VESA
(A * B)
200 * 100
Model
32LG30, 32LG60, 32LG70
LCD TV
PLASMA TV
Standard Screw
Quantity
M4
37LG30, 37LG60, 37LG50
42LG30, 42LG50, 42LG60, 42LG70, 42LGX
47LG50, 47LG60, 47LG70, 47LG90
200 * 200
M6
52LG50, 52LG60, 52LG70
800 * 400
M6
42PG25
50PG25, 50PG60, 50PG70
400 * 400
M6
60PG60, 60PG70
600 * 400
M8
! NOTE
Screw length needed depends on the wall mount
used. For further information, refer to the instructions included with the mount.
Standard dimensions for wall mount kits are shown
in the table.
When purchasing our wall mount kit, a detailed
installation manual and all parts necessary for
assembly are provided.
Do not use screws longer then the standard dimension, as they may cause damage to the inside to
the TV.
For wall mounts that do not comply with the VESA
standard screw specifications, the length of the
screws may differ depending on their specifications.
Do not use screws that do not comply with the
VESA standard screw specifications.
Do not use fasten the screws too strongly, this may
damage the TV or cause the TV to a fall, leading to
personal injury. LG is not liable for these kinds of
accidents.
LG is not liable for TV damage or personal injury
when a non-VESA or non specified wall mount is
used or the consumer fails to follow the TV installation instructions.
CAUTION
Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric
shock.
17
PREPARATION
CABLE MANAGEMENT
■
Image shown may differ from your TV.
PREPARATION
Plasma TV Models
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as
shown.
If your TV has the CABLE HOLDER, install it
as shown and bundle the cables.
CABLE HOLDER
CABLE MANAGEMENT CLIP
How to remove the CABLE MANAGEMENT CLIP
42PG25
First, press the cable management. Hold the
C A B L E M A N A G E M E N T C L I P with both
hands and pull it upward.
50PG25, 50/60PG60, 50/60PG70
Hold the CABLE MANAGEMENT CLIP with both
hands and pull it upward.
Separate C A B L E M A N A G E M E N T C L I P from TV
by pressing two latches.
! NOTE
18
Do not hold the CABLE MANAGEMENT CLIP when moving the TV.
- If the TV is dropped, you may be injured or the product may be broken.
LCD TV Models
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
Install the CABLE MANAGEMENT CLIP as
shown.
32/37/42/47/52LG60, 42LGX
Align the hole with the tab on the C A B L E
M A N A G E M E N T C L I P.
Turn the C A B L E M A N A G E M E N T C L I P as
shown.
Note: This cable management clip can be broken by excessive pressure.
Connect the cables as necessary.
To connect additional equipment, see the
EXTERNAL EQUIPMENT SETUP section.
PREPARATION
32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70, 47LG90
CABLE MANAGEMENT CLIP
Put the cables inside the CABLE MANAGEMENT
CLIP and snap it closed.
19
PREPARATION
DESKTOP PEDESTAL INSTALLATION
■
Image shown may differ from your TV.
For proper ventilation, allow a clearance of 4 inches on all four sides from the wall.
PREPARATION
4 inches
4 inches
4 inches
CAUTION
4 inches
Ensure adequate ventilation by following the clearance recommendations.
Do not mount near or above any type of heat source.
SWIVEL STAND
After installing the TV, you can adjust the TV set manually to the left or right direction by 20 degrees to suit
your viewing position.
ATTACHING THE TV TO A DESK (Only 32LG30/70, 42LG30/50)
The TV must be attached to a desk so it cannot be pulled in a forward/backward direction, potentially causing
injury or damaging the product.
Stand
1-Screw
(provided as parts of the product)
Desk
WARNING
20
To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the machine may cause injury.
SECURING THE TV TO THE WALL TO PREVENT FALLING
WHEN THE TV IS USED ON A STAND
■
You should purchase necessary components to prevent TV from falling off of the stand.
Image shown may differ from your TV.
We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.
■
PREPARATION
■
Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts.
* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.
Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is
mounted on the wall to the holes in the product.
Ensure the eye-bolts or brackets are tightened securely.
■
Use a sturdy rope (sold separately) to tie the product. It is safer to tie
the rope so it becomes horizontal between the wall and the product.
! NOTE
Use a platform or cabinet strong enough and large enough to support the size and weight of the TV.
To use the TV safely make sure that the height of the bracket on the wall and the one on the TV are the same.
21
PREPARATION
■
To prevent damage do not connect to the power outlet until all connections are made between the devices.
ANTENNA OR CABLE CONNECTION
Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connection.
For optimum picture quality, adjust the antenna direction if needed.
Wall
Antenna
Socket
Outdoor
Antenna
(VHF, UHF)
Multi-family Dwellings/Apartments
(Connect to wall antenna socket)
ANTENNA/
CABLE IN
RF Coaxial Wire (75 ohm)
Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)
PREPARATION
1. Antenna (Analog or Digital)
Copper Wire
Be careful not to bend the copper wire
when connecting the antenna.
2. Cable
ANTENNA/
CABLE IN
Cable TV
Wall Jack
RF Coaxial Wire (75 ohm)
To improve the picture quality in a poor signal area, please purchase a signal amplifier( and
install properly.
If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.
■ If the antenna is not installed properly, contact your dealer for assistance.
■
■
22
EXTERNAL EQUIPMENT SETUP
■
To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment.
■
Image shown may differ from your TV.
HD RECEIVER SETUP
This TV can receive digital over-the-air/digital cable signals without an external digital set-top box. However, if
you do receive digital signals from a digital set-top box or other digital external device.
EXTERNAL EQUIPMENT SETUP
Component Connection
1. How to connect
Connect the video outputs (Y, PB, PR) of the digital settop box to the C O M P O N E N T I N V I D E O 1 jacks on
the TV. Match the jack colors (Y = green, PB = blue, and
PR = red).
Connect the audio output of the digital set-top box to
the C O M P O N E N T I N A U D I O 1 jacks on the TV.
2. How to use
■
■
■
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box. operation)
Select the C o m p o n e n t 1 input source on the TV using
the I N P U T button on the remote control.
If connected to C O M P O N E N T I N 2 input, select the
C o m p o n e n t 2 input source on the TV.
Supported Resolutions
Signal
Y, CB/PB, CR/PR
Component
HDMI
480i
Yes
No
480p
Yes
Yes
720p
Yes
Yes
1080i
Yes
Yes
1080p
Yes
Yes
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480i
15.73
15.73
59.94
60.00
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.94
60.00
23
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70, 47LG90
PB
PR
EXTERNAL EQUIPMENT SETUP
RGB IN
DIGI
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
OPT
RS-232
(CONTROL &
PB
PR
AUDIO
VIDEO
S-VIDEO
COMPONENT IN
AUDIO
(RGB/DVI)
HDMI/DVI IN
RGB IN
VIDEO
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
COAXIAL
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
24
PB
PR
HDMI Connection
1. How to connect
Connect the digital set-top box to H D M I / D V I I N 1,
2 , 3 , or 4 jack on the TV.
No separate audio connection is necessary.
HDMI supports both audio and video.
2. How to use
Turn on the digital set-top box.
(Refer to the owner’s manual for the digital set-top box.)
■ Select the H D M I 1, H D M I2, H D M I 3, or H D M I 4 input
source on the TV using the INPUT button on the remote
control.
■
EXTERNAL EQUIPMENT SETUP
HDMI-DTV
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
720x480p
31.47
31.50
59.94
60.00
1280x720p
44.96
45.00
59.94
60.00
1920x1080i
33.72
33.75
59.94
60.00
1920x1080p
26.97
27.00
33.71
33.75
67.432
67.50
23.976
24.00
29.97
30.00
59.939
60.00
25
EXTERNAL EQUIPMENT SETUP
32/37/42LG30, 37/42/47/52LG50, 32LG70
Plasma TV, 42/47/52LG70, 47LG90
RGB IN
RGB IN
HDMI/DVI IN
(RG
RGB(PC)
RGB(PC)
EXTERNAL EQUIPMENT SETUP
HDMI/DVI IN
PR
PB
VIDEO
COMPONENT
PR
VIDEO
COMPON
HDMI-DTV OUTPUT
HDMI-DTV OUTPUT
AUDIO
(RGB/DVI)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
RGB(PC)
HDMI/DVI IN
COAXIAL
OPTICAL
HDMI-DTV OUTPUT
RGB IN
VIDEO
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
26
PB
DVI to HDMI Connection
1. How to connect
32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV
- Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1, 2 , or 3 jack on the TV.
32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90
- Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1, 2 , 3 , or 4 jack on the TV.
Connect the PC audio output to the A U D I O ( R G B / D V I ) jack on the TV.
2. How to use
Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)
■ 32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV
- Select the HDMI1, HDMI2, or HDMI3 input source on the TV using the I N P U T button on the remote control.
■ 32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90
- Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the I N P U T button on the remote
control.
■
! NOTE
EXTERNAL EQUIPMENT SETUP
A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio,
so a separate audio connection is necessary.
27
EXTERNAL EQUIPMENT SETUP
32/37/42LG30, 37/42/47/52LG50, 32LG70
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
Plasma TV, 42/47/52LG70, 47LG90
RGB IN
HDMI/DVI IN
REMO
CONTRO
AUDIO
(RGB/DVI)
RGB(PC)
REMOT
CONTROL
HDMI/DVI IN
EXTERNAL EQUIPMENT SETUP
PR
PB
PB
PR
AUDIO
VIDEO
COMPONENT IN
DVI-DTV OUTPUT
DVI-DTV OUTPUT
COAXIAL
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
28
RGB(PC)
HDMI/DVI IN
AUDIO
(RGB/DVI)
OPTICAL
DVI-DTV OUTPUT
RGB IN
VIDEO
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
AUDIO
VIDEO
COMPONENT IN
AV IN 1
DVD SETUP
Component Connection
1. How to connect
Connect the video outputs (Y, PB, PR) of the DVD to the
C O M P O N E N T I N V I D E O 1 jacks on the TV.
Match the jack colors (Y = green, PB = blue, and PR = red).
Connect the audio outputs of the DVD to the
C O M P O N E N T I N A U D I O 1 jacks on the TV.
2. How to use
■
■
■
■
Turn on the DVD player, insert a DVD.
Select the C o m p o n e n t 1 input source on the TV using
the I N P U T button on the remote control.
If connected to C O M P O N E N T I N 2 input, select the
C o m p o n e n t 2 input source on the TV.
Refer to the DVD player's manual for operating instructions.
EXTERNAL EQUIPMENT SETUP
Component Input ports
To get better picture quality, connect a DVD player to the component input ports as shown below.
Component ports on the TV
Video output ports
on DVD player
PB
PR
PB
PR
B-Y
R-Y
Cb
Cr
Pb
Pr
29
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70, 47LG90
PB
PR
EXTERNAL EQUIPMENT SETUP
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOT
CONTROL
PB
PR
AUDIO
VIDEO
COMPONENT IN
AUDIO
(RGB/DVI)
HDMI/DVI IN
RGB IN
VIDEO
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
COAXIAL
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
30
PB
PR
S-Video Connection (Except 32/37/42/47/52LG60, 42LGX)
AUDIO
S-VIDEO
Connect the S-VIDEO output of the DVD to the
S - V I D E O input on the TV.
Connect the audio outputs of the DVD to the A U D I O
input jacks on the TV.
ANTENNA/
CABLE IN
2. How to use
■
■
Turn on the DVD player, insert a DVD.
Select the A V 1 input source on the TV using the I N P U T
button on the remote control.
Refer to the DVD player's manual for operating instructions.
UDIO
B/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
AUDIO OUT
AUDIO
COAXIAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
■
DIGITAL AUDIO OUT
EXTERNAL EQUIPMENT SETUP
1. How to connect
31
EXTERNAL EQUIPMENT SETUP
HDMI Connection
32/37/42LG30, 37/42/47/52LG50,
32LG70
1. How to connect
EXTERNAL EQUIPMENT SETUP
HDMI/DVI IN
Connect the HDMI output of the DVD to the
H D M I / D V I I N 1, 2 , 3 or 4 jack on the TV.
AUDIO
(RGB/D
RGB(PC)
No separate audio connection is necessary.
HDMI supports both audio and video.
PR
PB
VIDEO
COMPONENT IN
2. How to use
■
■
Select the HDMI1, H D M I2, HDMI3, or HDMI4 input
source on the TV using the I N P U T button on the remote
control.
Refer to the DVD player's manual for operating instructions.
HDMI-DVD OUTPUT
PB
PR
VIDEO
COMPONENT
DIGITAL
AUDIO OUT
COAXIAL
OPTICAL
ANTENNA/
CABLE IN
REMOTE
CONTROL IN
HDMI-DVD OUTPUT
HDMI-DVD OUTPUT
32
AUDIO
(RGB/DVI)
RS-232C IN
(SERVICE ONLY)
RGB(PC)
HDMI/DVI IN
COMPONENT IN
RGB IN
(R
AUDIO
RGB(PC)
VIDEO
RGB IN
HDMI/DVI IN
32/37/42/47/52LG60, 42LGX
Plasma TV, 42/47/52LG70, 47LG90
VCR SETUP
To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
■ Use the ISM feature in the Option menu to avoid having a fixed image remain on the screen for a long period
of time (Plasma TV models only). If the 4:3 picture format is used; the fixed images on the sides of the screen
may remain visible on the screen. This phenomenon is common to all TVs and is not covered by warranty.
■
Connect the RF antenna out socket of the
VCR to the A N T E N N A / C A B L E I N socket on the TV.
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70, 47LG90
ANTENNA/
CABLE IN
UDIO OUT
COAXIAL
Connect the antenna cable to the RF
antenna in socket of the VCR.
E)
ANT IN
OUTPUT
SWITCH
AV IN 1
EO L (MONO) AUDIO R
VIDEO
Wall Jack
Antenna
32/37/42/47/52LG60, 42LGX
COMP
■
Set VCR output switch to 3 or 4 and then
tune TV to the same channel number.
Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner’s
manual.)
S-VIDEO
AUDIO OUT
2. How to use
■
ANT OUT
AUDIO
1. How to connect
EXTERNAL EQUIPMENT SETUP
Antenna Connection
COAX
OPTIC
ANTENNA/
CABLE IN
S-VIDEO
VIDEO
ANT OUT
RS-232C IN
(SERVICE ONLY)
ANT IN
OUTPUT
SWITCH
Wall Jack
REMOTE
CONTROL IN
Antenna
33
EXTERNAL EQUIPMENT SETUP
Composite (RCA) Connection
Plasma TV, 32/37/42LG30,
37/42/47/52LG50,
32/42/47/52LG70, 47LG90
1. How to connect
EXTERNAL EQUIPMENT SETUP
V I D E O jacks between TV and
Connect the A U D I O/V
VCR. Match the jack colors (Video = yellow, Audio Left
= white, and Audio Right = red)
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
2. How to use
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
■ Select the A V 1 input source on the TV using the I N P U T
button on the remote control.
■ If connected to A V I N 2, select A V 2 input source on the TV.
■
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
COAXIAL
AUDIO OUT
! NOTE
If you have a mono VCR, connect the audio cable from
the VCR to the A U D I O L / M O N O jack of the TV.
AUDIO
S-VIDEO VIDEO L (MONO) AUDIO R
HDMI IN 4
USB IN
NT IN
VIDEO L/MONO AUDIO R
32/37/42/47/52LG60, 42LGX
AV IN
34
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
AV IN 1
S-Video Connection (Except 32/37/42/47/52LG60, 42LGX)
1. How to connect
Connect the audio outputs of the VCR to the A U D I O
input jacks on the TV.
ANT IN
S-VIDEO
ANT OUT
OUTPUT
SWITCH
VIDEO
2. How to use
■
■
Insert a video tape into the VCR and press PLAY on the VCR.
(Refer to the VCR owner’s manual.)
Select the A V 1 input source on the TV using the I N P U T
button on the remote control.
ANTENNA/
CABLE IN
DIGITAL
AUDIO OUT
AUDIO
(RGB/DVI)
REMOTE
CONTROL IN
OPTICAL
RS-232C IN
(CONTROL & SERVICE)
! NOTE
S-Video provides better quality than composite. Use it
when available.
AUDIO OUT
AUDIO
NT IN
COAXIAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
Connect the S-VIDEO output of the VCR to the
S - V I D E O input on the TV.
EXTERNAL EQUIPMENT SETUP
CAUTION
Do not connect to both Video and S-Video at the same
time. In the event that you connect both Video and the
S-Video cables, only the S-Video will work.
35
EXTERNAL EQUIPMENT SETUP
OTHER A/V SOURCE SETUP
Camcorder
1. How to connect
■
■
Select the A V 2 input source on the TV using
the I N P U T button on the remote control.
If connected to A V I N 1 input, select the A V 1
input source on the TV.
Operate the corresponding external equipment.
USB IN
VIDEO
HDMI IN 3
2. How to use
■
36
V I D E O jacks
Connect the A U D I O/V
between TV and external equipment.
Match the jack colors.
(Video = yellow, Audio Left = white, and
Audio Right = red)
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
Video Game Set
PC SETUP
This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.
VGA (D-Sub 15 pin) Connection
(CO
PB
PR
DIGITAL
AUDIO OUT
AUDIO
(RGB/DVI)
COAXIAL
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
AUDIO
VIDEO
COMPONENT IN
RS-232C IN
(SERVICE ONLY)
HDMI/D
REMOTE
CONTROL IN
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
VIDEO
RGB IN
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
EXTERNAL EQUIPMENT SETUP
Plasma TV, 32/37/42LG30, 37/42/47/52LG50,
32/42/47/52LG70, 47LG90
REMOTE
CONTROL IN
RGB OUTPUT
AUDIO
RGB OUTPUT
AUDIO
1. How to connect
Connect the VGA output of the PC to the R G B ( P C) jack on the TV.
Connect the PC audio output to the A U D I O ( R G B / D V I) jack on the TV.
2. How to use
■
■
Turn on the PC and the TV.
Select the R G B - P C input source on the TV using the I N P U T button on the remote control.
37
EXTERNAL EQUIPMENT SETUP
DVI to HDMI Connection
1. How to connect
EXTERNAL EQUIPMENT SETUP
32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV
- Connect the DVI output of the PC to the H D M I / D V I I N 1, 2 , or 3 jack on the TV.
32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90
- Connect the DVI output of the PC to the H D M I / D V I I N 1, 2 , 3 , or 4 jack on the TV.
Connect the PC audio output to the A U D I O ( R G B / D V I ) jack on the TV.
2. How to use
■
■
■
Turn on the PC and the TV.
32/37/42LG30, 37/42/47/52LG50, 32LG70, Plasma TV
- Select the HDMI1, HDMI2, or HDMI3 input source on the TV using the I N P U T button on the remote control.
32/37/42/47/52LG60, 42/47/52LG70, 42LGX, 47LG90
- Select the HDMI1, HDMI2, HDMI3, or HDMI4 input source on the TV using the I N P U T button on the remote
control.
! NOTES
38
32/37/42LG30, 42/50PG25: To get the the best
picture quality, adjust the PC graphics card to
1360x768.
37/42/47/52LG50, 32/37/42/47/52LG60,
32/42/47/52LG70, 42LGX, 47LG90,
50/60PG60, 50/60PG70: To get the the best
picture quality, adjust the PC graphics card to
1920x1080.
Depending on the graphics card, DOS mode may
not work if a HDMI to DVI Cable is in use.
In PC mode, there may be noise associated with
the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to
another resolution, change the refresh rate to
another rate or adjust the brightness and contrast
on the PICTURE menu until the picture is clear.
Avoid keeping a fixed image on the screen for a
long period of time. The fixed image could become
permanently imprinted on the screen.
The synchronization input form for Horizontal and
Vertical frequencies is separate.
32/37/42LG30, 37/42/47/52LG50, 32LG70
Plasma TV, 42/47/52LG70, 47LG90
RGB IN
AUDIO
(RGB/DVI)
RGB(PC)
REMO
CONTRO
RGB IN
HDMI/DVI IN
AUDIO
(RGB/DVI)
RGB(PC)
REMOTE
CONTROL IN
HDMI/DVI IN
(CO
PR
PB
AUDIO
VIDEO
AUDIO
VIDEO
COMPONENT IN
DVI-PC OUTPUT
AUDIO
DVI-PC OUTPUT
PR
COMPONENT IN
PB
AV IN 1
EXTERNAL EQUIPMENT SETUP
AUDIO
AUDIO
(RGB/DVI)
HDMI/DVI IN
RGB IN
VIDEO
DIGITAL
AUDIO OUT
AUDIO
COMPONENT IN
32/37/42/47/52LG60, 42LGX
COAXIAL
OPTICAL
RGB(PC)
ANTENNA/
CABLE IN
RS-232C IN
(SERVICE ONLY)
REMOTE
CONTROL IN
DVI-PC OUTPUT
AUDIO
39
EXTERNAL EQUIPMENT SETUP
Supported Display Specifications (RGB-PC, HDMI-PC)
! NOTE
EXTERNAL EQUIPMENT SETUP
Depending on the graphics card, some resolution settings may not allow the image to be positioned on the
screen properly.
If there are overscan in HDMI-PC 1920x1080, change aspect ratio to J u s t s c a n.
For 32/37/42LG30
For 37/42/47/52LG50, 32/37/42/47/52LG60,
32/42/47/52LG70, 42LGX, 47LG90
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.469
70.08
640x350
31.468
70.09
720x400
31.469
70.08
720x400
31.469
70.08
640x480
31.469
59.94
640x480
800x600
37.879
60.31
31.469
37.500
37.861
59.94
75.00
72.80
1024x768
48.363
60.00
1280x768
47.776
59.87
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
1360x768
47.720
59.799
1366x768
47.130
59.65
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.87
74.893
1280x1024
63.981
79.976
60.02
75.025
1360x768
47.712
60.015
1600x1200
75.00
60.00
66.587
59.934
67.5
60.00
* Only RGB-PC mode
1920x1080
RGB-PC
1920x1080
HDMI-PC
* Only RGB-PC mode
40
Resolution
Horizontal
Frequency(KHz)
Vertical
Frequency(Hz)
640x350
31.468
70.09
720x400
31.469
70.08
640x480
31.469
37.500
37.861
59.94
75.00
72.80
800x600
35.156
37.879
46.875
48.077
56.25
60.31
75.00
72.18
1024x768
48.363
56.476
60.023
60.00
70.06
75.02
1280x768
47.776
60.289
59.87
74.893
1280x1024
63.981
79.976
60.02
75.025
1360x768
47.712
60.015
1600x1200
75.00
60.00
1920x1080
66.587
59.934
EXTERNAL EQUIPMENT SETUP
For 42/50PG25, 50/60PG60, 50/60PG70
* Only RGB-PC mode
41
EXTERNAL EQUIPMENT SETUP
Screen Setup for PC mode
Selecting Resolution
You can choose the resolution in RGB-PC mode.
The P o s i t i o n, P h a s e, and S i z e can also be adjusted.
EXTERNAL EQUIPMENT SETUP
PICTURE
Move
SCREEN
Enter
• Brightness
50
• Sharpness
60
• Color
60
• Tint
Resolution
Auto config.
• Advanced Control
• Reset
Screen (RGB-PC)
Position
Size
Phase
TruMotion Demo
Reset
1 MENU
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select R e s o l u t i o n.
ENTER
ENTER
42
Select P I C T U R E.
Select the desired resolution.
Move
MENU Prev.
1024 x 768
1280 x 768
1360 x 768
1366 x 768
Only for
32/37/42LG30
Auto Configure
Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still
not correct, try using the manual settings or a different resolution or refresh rate on the PC.
Move
SCREEN
Enter
• Brightness
50
• Sharpness
60
• Color
60
• Tint
Move
MENU Prev.
Resolution
Auto config. G
• Advanced Control
• Reset
Position
Size
To Set
Yes
No
Screen (RGB-PC)
TruMotion Demo
Phase
Reset
1 MENU
Select P I C T U R E.
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select A u t o c o n f i g ..
ENTER
Select Y e s.
ENTER
EXTERNAL EQUIPMENT SETUP
PICTURE
• If the position of the image is still not
correct, try Auto adjustment again.
• If picture needs to be adjusted again
after Auto adjustment in RGB-PC, you
can adjust the P o s i t i o n , S i z e or
P h a s e.
Start Auto Configuration.
43
EXTERNAL EQUIPMENT SETUP
Adjustment for screen Position, Size, and Phase
PICTURE
Move
SCREEN
Enter
EXTERNAL EQUIPMENT SETUP
If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture
phase manually.
This feature operates only in RGB-PC mode.
• Brightness
50
• Sharpness
60
• Color
60
• Tint
Move
MENU Prev.
Resolution
Auto config.
• Advanced Control
Position
• Reset
Size
Screen (RGB-PC)
TruMotion Demo
Phase
Reset
1 MENU
■
ENTER
Select S c r e e n ( R G B - P C ).
■
ENTER
Select P o s i t i o n, S i z e, or P h a s e.
■
ENTER
ENTER
44
Select P I C T U R E.
Make appropriate adjustments.
P o s i t i o n: This function is to adjust picture to left/right and up/down as you
prefer.
S i z e: This function is to minimize any
vertical bars or stripes visible on the
screen background. And the horizontal
screen size will also change.
P h a s e : This function allows you to
remove any horizontal noise and clear or
sharpen the image of characters.
Screen Reset (Reset to original factory values)
Returns P o s i t i o n, S i z e, and P h a s e to the default factory settings.
This feature operates only in RGB-PC mode.
Move
SCREEN
Enter
• Brightness
50
• Sharpness
60
• Color
60
• Tint
Move
MENU Prev.
Resolution
Auto config.
• Advanced Control
• Reset
Position
To Set
Yes
Size
No
EXTERNAL EQUIPMENT SETUP
PICTURE
Screen (RGB-PC)
Phase
TruMotion Demo
Reset
1 MENU
Select P I C T U R E.
ENTER
Select S c r e e n ( R G B - P C ).
ENTER
Select R e s e t.
ENTER
Select Y e s.
ENTER
45
EXTERNAL EQUIPMENT SETUP
USB CONNECTION (Except 32/37/42LG30)
or
VIDEO L/MONO AUDIO R
EXTERNAL EQUIPMENT SETUP
HDMI IN 3
USB IN
i.e)
AV IN 2
1. How to connect
Connect the USB device to the U S B I N jack on the side
of TV.
2. How to use
■
After connecting the U S B I N jack, you use the USB func-
tion. (G p .64)
46
AUDIO OUT CONNECTION
Send the TV’s audio to external audio equipment via the Audio Output port.
Analog (Except 32/37/42/47/52LG60, 42LGX)
1. How to connect
RS-232C IN
(CONTROL & SERVICE)
S-VIDEO VIDEO L (MONO) AUDIO R
Set the “TV Speaker option - Off” in the AUDIO menu.
(G p . 9 3). See the external audio equipment instruction
manual for operation.
AV IN 1
AUDIO
EXTERNAL EQUIPMENT SETUP
Connect audio outputs to the TV’s AUDIO OUT jacks.
AUDIO OUT
Digital
AUDIO
1. How to connect
Connect one end of the optical or coaxial cable to the
TV’s O P T I C A L or COAXIAL (Except 32/37/42LG30)
port of D I G ITAL AUDIO OUT.
Connect the other end of the optical or coaxial cable to
the digital audio input on the audio equipment.
ANTENNA/
CABLE IN
DIGITAL AUDIO OUT
UDIO
B/DVI)
Set the “TV Speaker option - Off” in the AUDIO menu. (G
p .93). See the external audio equipment instruction manual for operation.
RS-232C IN 1
(CONTROL & SERVICE)
When connecting with external audio equipments, such as
amplifiers or speakers, you can turn the TV speakers off in
the menu. (G p . 9 3)
COAXIAL
AUDIO OUT
AUDIO
! NOTE
OPTICAL
S-VIDEO VIDEO L (MONO) AUDIO R
AV IN 1
REMOTE
CONTROL IN
CAUTION
Do not look into the optical output port. Looking at the
laser beam may damage your vision.
Block the SPDIF out (optical/coaxial) about the contents
with ACP(Audio Copy Protection) function.
47
WATCHING TV / CHANNEL CONTROL
REMOTE CONTROL FUNCTIONS
When using the remote control, aim it at the remote control sensor on the TV.
TV/STB/DVD/VCR Select the remote operating mode: TV, STB, DVD, or VCR.
POWER Turns your TV or any other programmed equipment on or
off, depending on the mode.
POWER
STB
Q. MENU MENU
DVD
VCR
INPUT
WATCHING TV / CHANNEL CONTROL
Q.MENU Select the desired quick menu source. G p.51
MENU Displays the main menu.
Clear all on-screen displays and return to TV viewing from
any menu.
ENTER
INPUT External input modes rotate in regular sequence.
VOLUME UP Increase/decrease the sound level.
/DOWN
RETURN
AV MODE
FAV Scroll through the programmed Favorite channels. G p.51
FAV
MUTE Switch the sound on or off. G p.50
NUMBER button
— (DASH) Used to enter a program number for multiple
program channels such as 2-1, 2-2, etc.
FLASHBK Tune to the last channel viewed.
VCR/DVD, USB,
SIMPLINK
Control buttons
Control video cassette recorders or DVD players.
Control USB menu (PHOTO LIST and MUSIC LIST.)
Control the SIMPLINK compatible devices.
CH
VOL
CHANNEL Select available channels.
UP/DOWN
PAGE Move from one full set of screen information to the next one.
UP/DOWN
48
TV
MUTE
FLASHBK
THUMBSTICK Navigate the on-screen menus and adjust the system settings to your preference.
(Up/Down/Left
Right/ENTER)
RETURN Allows the user to move return one step in an interactive application or other user interaction
function.
AV MODE It helps you select and set images and sounds. G p.61
WATCHING TV / CHANNEL CONTROL
SIMPLINK See a list of AV devices connected to TV.
When you toggle this button, the SIMPLINK menu appears at the screen. G p.62-63
Installing Batteries
■
Open the battery compartment cover on the back side and install
the batteries matching correct polarity (+with +,-with -).
■
Install two 1.5V AAA batteries. Don’t mix old or used batteries with
new ones.
■
Close cover.
49
WATCHING TV / CHANNEL CONTROL
TURNING ON THE TV
First, connect power cord correctly.
At this moment, the TV switches to standby mode.
■ In standby mode to turn TV on, press the
, INPUT, CH (DE or
), Number
button on the TV or press the POWER, INPUT, CH(
or
( 0~9
9 ) button on the remote control.
WATCHING TV / CHANNEL CONTROL
Select the viewing source by using the INPUT button on the remote control.
■ This TV is programmed to remember which power state it was last set to,
even if the power cord is out.
When finished using the TV, press the POWER button on the remote control.
The TV reverts to standby mode.
! NOTE
If you intend to be away on vacation, disconnect the power plug from the wall power outlet.
CHANNEL SELECTION
Press the C H (
or
) or NUMBER buttons to select a channel number.
VOLUME ADJUSTMENT
Adjust the volume to suit your personal preference.
50
Press the V O L ( + or - ) button to adjust the volume.
If you want to switch the sound off, press the M U T E button.
You can cancel the Mute function by pressing the MUTE or V O L ( + or - )
button.
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 52
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:57a47b37-dae5-4942-bb58-99fefec5d027
Modify Date                     : 2008:06:18 15:23:14+09:00
Create Date                     : 2008:06:18 15:22:58+09:00
Metadata Date                   : 2008:06:18 15:23:14+09:00
Document ID                     : uuid:20b7ed3c-c2f5-475b-8d81-08f9ddec75a3
Format                          : application/pdf
Title                           : SAC30708020-Edit1-en_6
Creator                         : 3.3: LaserWriter 8 Z1-8.7.1
Author                          : sun
Producer                        : Acrobat Distiller 4.0 for Macintosh
EXIF Metadata provided by EXIF.tools
FCC ID Filing: BEJ42LG70UG

Navigation menu