LG Electronics USA 42PC3DUD Plasma Display Panel User Manual 527A
LG Electronics USA Plasma Display Panel 527A
Contents
- 1. Users Manual Part 1
- 2. Users Manual Part 2
- 3. Users Manual Part 3
Users Manual Part 3
HDMI/DVI IN DIGITAL AUDIO OUT OPTICAL AUDIO IN (RGB/DVI) CABLE IN RS-232C IN (CONTROL & SERVICE) REMOTE CONTROL RGB IN (PC/DTV) Installation HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. When connecting with a D-sub 15 pin cable Connect the RGB output of the digital set-top box to the RGB IN (PC/DTV) ( 32/37/42LC2D Model)/ RGB (PC/DTV) (42PC3D/3DV/50PC3D Model) jack on the set. Connect the audio outputs of the set-top box to the AUDIO IN (RGB/DVI) ( 32/37/42LC2D Model) /AUDIO (RGB/DVI) (42PC3D/3DV/50PC3D Model) jack on the set. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select RGB-DTV input source with using the INPUT button on the remote control. REMOTE CONTROL AUDIO IN (RGB/DVI) RGB IN (PC/DTV) (R) AUDIO (L) RGB-DTV OUTPUT Digital Set-top Box When connecting with a HDMI cable HDMI/DVI IN DIGITAL AUDIO OUT OPTICAL RS-232C IN (CONTROL & SERVICE) Connect the HDMI output of the digital set-top box to the HDMI/DVI IN jack on the set. Select HDMI/DVI input source with using the INPUT button on the remote control. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) AUDIO NT IN HDMI-DTV OUTPUT Digital Set-top Box • TV can receive the video and audio signal simultaneously with using a HDMI cable. • If the digital set-top box supports Auto HDMI function, output resolution of the digital set-top box will be automatically set to 1280x720p. ANTENNA set-top box does not support Auto HDMI, you need to set the output resolution appro• If the digital IN priately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. CABLE IN -232C IN ROL & SERVICE) AUDIO IN (RGB/DVI) RGB IN (PC/DTV) 26 REMOTE CONTROL Installation When connecting with a Component cable Connect the video outputs (Y, PB, PR) of the digital set-top box to the COMPONENT IN VIDEO jacks on the set. IN DIGITAL AUDIO OUTtheRS-232C ConnectHDMI/DVI the audio output digital set-top box HDMI/DVI IN IN & SERVICE) (CONTROL DIGITAL AUDIO OUT of RS-232C OPTICAL IN (CONTROL & SERVICE) OPTICAL to the COMPONENT IN AUDIO jacks on the set. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) Select Component 1 input source with using the INPUT button on the remote control. Digital Set-top Box (R) AUDIO (L) AV V OUT AV OUT (MONO) S-VIDEO VIDEO( AUDIO UDIO S-VIDEO VIDEO AUDIO AV V IN 1 AV IN 1 VIDEO VIDEO AUDIO UDIO AUDIO Signal COMPONENT IN COMPONENT IN Component1/2 RGB-DTV, HDMI/DVI 480i Yes No 480p/720p/1080i Yes Yes When connecting with a HDMI to DVI cable ANTENNA ANTENNAIN IN HDMI/DVI IN HDMI/DVI IN CABLE CABLE IN IN RS-232C IN DIGITAL AUDIO OUT RS-232C IN & SERVICE) (CONTROL DIGITAL AUDIO OUT OPTICAL (CONTROL & SERVICE) OPTICAL REMOTE AUDIO IN REMOTE AUDIO(RGB/DVI) IN CONTROL CONTROL (RGB/DVI) RGB IN (PC/DTV) RGB IN (PC/DTV) DVI-DTV OUTPUT (R) AUDIO (L) Digital Set-top Box Connect the DVI output of the digital set-top box to the HDMI/DVI IN jack on the set. Connect the audio outputs of the set-top box to the AUDIO IN (RGB/DVI) ( 32/37/42LC2D Model) /AUDIO (RGB/DVI) (42PC3D/3DV/50PC3D Model) jack on the set. REMOTE AUDIO IN Turn on the digital set-top box. (Refer owner’s manual for the digital set-top box.) REMOTE AUDIOto IN the CONTROL (RGB/DVI) (RGB/DVI) CONTROL Select HDMI/DVI input source with using the INPUT button on the remote control. RGB IN (PC/DTV) RGB IN (PC/DTV) • If the digital set-top box has a DVI output and no HDMI output, a separated audio connection is necessary. • If the digital set-top box supports Auto DVI function, the output resolution of the digital set-top box will be automatically set to 1280x720p. • If the digital set-top box does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the digital set-top box to 1280x720p. 27 Installation Monitor Out Setup - The TV has a special signal output capability which allows you to hook up a second TV or monitor. Connect the second TV or monitor to the TV’s AV OUTPUT jacks. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings. AV V OUT (MONO) VIDEO AUDIO UDIO S-VIDEO VIDEO AUDIO UDIO COMPONENT IN AV V IN 1 1/2 • Component 1-2, RGB-PC/RGB-DTV, HDMI/DVI, DTV input sources cannot be used for Monitor out. • When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (Refer to p.43) • We recommend to use the video and audio output jacks for VCR recording. S-VIDEO IN (R) AUDIO (L) VIDEO Digital Audio Output - Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port. HDMI/DVI IN DIGITAL AUDIO OUT OPTICAL 1/2 Connect one end of an optical cable to the TV Digital Audio Optical Output port. Connect the other end of the optical cable to the digital audio optical input on the audio equipment. See the external audio equipment instruction manual for operation. When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. (Refer to p.43) RS-232C IN (CONTROL & SERVICE) CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. 28 Installation PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. When connecting with a D-sub 15 pin cable AUDIO IN (RGB/DVI) REMOTE CONTROL Connect the RGB output of the PC to the RGB IN (PC/DTV) (32/37/42LC2D Model) / RGB (PC/DTV) (42PC3D/3DV/50PC3D Model) jack on the set. Connect the PC audio outputs to the AUDIO IN (RGB/DVI) (32/37/42LC2D Model) /AUDIO (RGB/DVI) (42PC3D/3DV/50PC3D Model) jack on the set. Turn on the PC and the set. Select RGB-PC input source with using the INPUT button on the remote control. RGB IN (PC/DTV) (R) AUDIO (L) RGB-PC OUTPUT PC When connecting with a HDMI to DVI cable ANTENNA IN HDMI/DVI HDMI/D VI IN DIGIT AUDIO DIGITAL UDIO OUT OPTICAL AUDIO IN (RGB/DVI) CABLE IN RS-232C IN (CONTROL & SER (CONTROL SERVICE) VICE) REMOTE CONTROL RGB IN (PC/DTV) DVI-PC OUTPUT (R) AUDIO (L) PC Connect the DVI output of the PC to the HDMI/DVI IN jack on the set. Connect the audio outputs of the PC to the AUDIO IN (RGB/DVI) (32/37/42LC2D Model) /AUDIO (RGB/DVI) (42PC3D/3DV/50PC3D Model) jack on the set. Turn on the PC and the set. Select HDMI/DVI input source with using the INPUT button on the remote control. AUDIO IN (RGB/DVI) REMOTE CONTROL RGB IN (PC/DTV) • If the PC has a DVI output and no HDMI output, a separated audio connection is necessary. • If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of PC graphics card's output resolution to 1024x768, 60Hz. 29 Installation 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. 3. When Source Devices connected with HDMI/DVI Input, output PC Resolution (VGA, SVGA, XGA), Position and Size may not fit to Screen.Press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center. 4. When Source Devices connected with HDMI/DVI Input, output TV SET Resolution (480p, 720p, 1080i) and TV SET Display fit EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center. 5. In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI/DVI Input. In case that Video Resolution is not supported TV SET output in HDMI/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI/DVI Source Devices or contact your service center. 6. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC, HDMI/DVI mode. If noise is present, change the PC or HDMI/DVI mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. 7. Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. 8. The synchronization input form for Horizontal and Vertical frequencies is separate. Supported Display Resolution (RGB-PC, HDMI/DVI Mode) Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) * 640x350 31.468 * 720x400 31.469 31.469 37.861 37.500 75.00 640x480 Horizontal Frequency (kHz) Vertical Frequency (Hz) 70.09 35.156 56.25 70.08 37.879 60.31 59.94 48.077 72.18 72.80 46.875 75.00 48.363 60.00 56.476 70.06 60.023 75.02 Resolution 800x600 1024x768 * RGB-PC only 30 Installation Screen Setup for PC mode When RGB connect to PC input and select the RGB-PC, this function is used. When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used. In RGB-DTV mode, SIZE and PHASE is not available. After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality. * Adjustment for screen Position, Size, and Phase POSITION SIZE FLASHBK ADJUST SAP FREEZE Adjust Close APM Press the ADJUST button and then use POSITION, SIZE, or PHASE. Press ENTER button and then use make appropriate adjustments. Mini Glossary Position This function is to adjust picture to left/right and up/down as you prefer. Size This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. Phase RESET EZ PIC EZ SOUND ADJUST PHASE D /E button to select D / E / F / G buttons to • The PHASE adjustment range is -30 ~ +30. (In HDMI/DVI-PC mode, PHASE is not available.) • The SIZE adjustment range is -30 ~ +30. Press ENTER button. This function allows you to remove any horizontal noise and clear or sharpen the image of characters. * Initializing (Reset to original factory values) FLASHBK POSITION SIZE ADJUST RESET EZ PIC EZ SOUND ADJUST Initialize Settings PHASE SAP FREEZE Adjust Close APM - To initialize the adjusted values Press the ADJUST button and then use the RESET option. Press ENTER button and then use F /G D /E button to select button to select Yes. Press ENTER button. 31 Operation Operation Basic operation Turning on the TV 1. First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the ON/OFF, INPUT, CH D / E button on the TV or press the POWER, TV INPUT, TV/VIDEO, CH D / E, Number (0 ~ 9) button on the remote control . 2. Select the viewing source by using TV INPUT, TV/VIDEO button on the remote control. This TV is programmed to remember which power state it was last set to, even if the power cord is out. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. Volume Adjustment D / E button to adjust the volume. 2. If you want to switch the sound off, press the MUTE button. 1. Press the VOL 3. You can cancel this function by pressing the MUTE or VOL button. Channel Selection Press the CH or NUMBER buttons to select a channel number. • If you intend to be away on vacation, disconnect the power plug from the wall power outlet. On Screen Menus Language Selection SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME LOCK LOCK English Español (Spanish) Français (French) MENU Previous Press the MENU button and then use OPTION menu. Press the 32 OPTION - The menus can be shown on the screen in the selected language. First select your language. Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power button and then use button to select the button to select Language. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Operation On Screen Menus Selection and Adjustment How to adjust the OSD screen 1. Press the MENU button and then 2. Press the G button and then use D /E /F /G SETUP VIDEO AUDIO TIME button to select each menu. button to display the available menus. EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Input Block SETUP VIDEO AUDIO TIME SETUP VIDEO AUDIO TIME OPTION OPTION LOCK EZ Picture Contrast 85 Brightness 50 Color 50 Sharpness 50 Tint Color Temperature Video Reset Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE 50 50 LOCK Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME OPTION SETUP VIDEO AUDIO TIME Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off OPTION LOCK LOCK * Note: These function are available in 42PC3D/3DV, 50PC3D models only. • Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. 33 Operation Setup Menu Options EZ Scan (Channel Search) SETUP VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. - Run EZ Scan again after any Antenna/Cable connection changes. - A password is required to gain access to EZ Scan menu if the Lock System is turned on. EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID MENU ANTENNA CABLE Selection ( G or Processing ) leads you EZ scan... to the EZ scan screen. TV Ch. 2 1 channel(s) found. Press to stop the current scan and start DIGITAL ANTENNA channel scan. Previous MENU Previous Press the MENU button and then use D / E button to select the SETUP menu. Press the G button and then use D /E button to select EZ Scan. Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE. Manual Scan SETUP VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - A password is required to gain access to Manual Scan menu if the Lock System is turned on. EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID MENU Select channel type and RF-channel number. TV Previous Press the MENU button and then use D / E button to select the SETUP menu. Press the G button and then use D /E button to select Manual Scan. Press the G button and then use D and CADTV. /E button to select TV, DTV, CATV, Press the G button and then use ber you want to add or delete. Press the ENTER button to add or delete for the channel number. D /E button to select channel num- Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Mini Glossary TV DTV 34 Analog antenna (over-the-air) TV signal Digital antenna (over-the-air) TV signal CATV CADTV Analog cable TV signal Digital cable TV signal Operation Channel Edit SETUP VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID MENU Selection ( G or ) leads you to the channel edit screen. Previous * Custom List - There are two different ways in order to add or delete scanned channels. One is "Custom List" and the other is "Favorite List" in the channel list. Both of them are available after EZ Scan on the SETUP menu. Press the MENU button and then use D / E button to select the SETUP menu. Press the G button. You will now see a screen filled with channel numbers and a preview picture. - A Custom List can be created by toggling each channel on or off with ENTER button. The channels in the Custom List are displayed in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen.You can create your own Favorite List. Use the FAV button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List. Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV button to add the channel to the Favorite List. The heart-mark will appear in front of that channel number. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Press the G button and then use D /E button to select Channel Edit. 35 Operation Setup Menu Options continued DTV Signal Strength SETUP VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation. - DTV Signals: Only when the input signal is DTV or CADTV, this function is available. EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID MENU Bad Normal Good Previous Press the MENU button and then use D / E button to select the SETUP menu. Press the G button and then use D /E button to select DTV Signal. View the on-screen signal strength monitor to see the quality of the signal being received. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Input Source SETUP VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - Changes the picture source so you can watch your TV, cable TV, VCR, DVD, or any other devices that are connected to your TV. 36 SETUP EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID MENU Antenna Cable AV1 AV2 Component1 Component2 RGB-PC HDMI/DVI Previous Press the G button and then use D Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Press the MENU button and then use D / E button to select the SETUP menu. /E button to select Input Source. Press the G button and then use D / E button to select the source: Antenna, Cable, AV1, AV2, Component1, Component2, RGB-DTV (or RGB-PC), or HDMI/DVI. • To toggle RGB-DTV and RGB-PC, select RGB-DTV(or RGB-PC) and press G button. Operation Input Label SETUP VIDEO AUDIO TIME EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - Sets a label to each input source or lets you skip the input source which is not in use when you press TV/VIDEO button. EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID MENU AV1 AV2 Component1 Component2 RGB HDMI/DVI Cable Box VCR DVD Set Top Box PC Game Previous Press the MENU button and then use D / E button to select the SETUP menu. Press the G button and then use D /E button to select Input Label. Press the G button and then use D / E button to select the source: AV1, AV2,Component1-2, RGB, or HDMI/DVI. Press the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. F /G button to select the label. 37 Operation V ideo Menu Options EZ Picture - EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category. - When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Custom. - Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable. FLASHBK EZ PIC EZ PIC EZ SOUND SAP FREEZE APM ADJUST Press the EZ PIC button repeatedly to select the picture appearance setup option as shown below: Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports. • You can also adjust EZ Picture in the VIDEO menu. Press the EXIT button to save and return to TV viewing. APM (Adaptive Picture Mode) FLASHBK EZ PIC EZ SOUND SAP Daylight Normal Night Time Custom FREEZE APM APM ADJUST - It allows a viewer to select their preferred mode after comparing picture (Daylight, Normal, Night Time and Custom) settings. - Note: While operating the 4-split, any button except APM, ENTER, EXIT, VOLUME D / E , MUTE button on the remote control are not available. 38 Navigate Select EXIT Exit Press the APM button. The screen is divided to 4-split. Press the D / E / F / G button to navigate 4 EZ Pictures. By pressing the ENTER button, you can select the desired mode. Press the EXIT button to save and return to TV viewing. Operation Manual Picture Control (EZ Picture-Custom option) SETUP VIDEO AUDIO TIME EZ Picture Contrast 85 Brightness 50 Color 50 Sharpness 50 Tint Color Temperature Video Reset SETUP 90 F AUDIO TIME OPTION LOCK Contrast VIDEO OPTION MENU LOCK Previous - Adjust the picture appearance to suit your preference and viewing situations. Press the MENU button and then use D / E button to select the VIDEO menu. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, or Tint). Press the G button and then use F / G button to make appropriate adjustments. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Color Temperature Control SETUP VIDEO AUDIO TIME EZ Picture Contrast 85 Brightness 50 Color 50 Sharpness 50 Tint Color Temperature Video Reset SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. EZ Picture Contrast Brightness Color Sharpness Tint Color Temperature Video Reset MENU Cool Medium Warm Previous Press the MENU button and then use D / E button to select the VIDEO menu. Press the G button and then use D / E button to select Color Temperature. Press the G button and then use Medium, or Warm. D /E button to select either Cool, Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Video Reset SETUP VIDEO AUDIO TIME EZ Picture Contrast 85 Brightness 50 Color 50 Sharpness 50 Tint Color Temperature Video Reset SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - Use to quickly reset all the Video menu options to their original factory preset values. EZ Picture Contrast Brightness Color Sharpness Tint Color Temperature Video Reset MENU Selection ( G or ) resets to the factory settings (default). Previous Press the MENU button and then use D / E button to select the VIDEO menu. Press the button and then use D /E button to select Video Reset. Press the G button to reset the Video menu options to original values. 39 Operation Audio Menu Options Audio Language SETUP VIDEO AUDIO TIME OPTION Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE SETUP VIDEO 50 50 AUDIO TIME OPTION LOCK LOCK - Other languages may be available if a digital signal is provided by the broadcasting station. Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE English Spanish French Previous MENU Press the MENU button and then use AUDIO menu. Press the G button and then use D / E button to select Audio Language. Press the G button and then use Spanish, or French. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. D / E D / E button to select the button to select: English, EZ SoundRite SETUP VIDEO AUDIO TIME OPTION Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE SETUP VIDEO 50 50 AUDIO TIME OPTION LOCK - Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. EZ SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. 40 LOCK Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE Off On Previous MENU Press the MENU button and then use AUDIO menu. Press the G button and then use D Press the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. button and then use /E D / E button to select the button to select EZ SoundRite. D /E button to select Off or On. Operation EZ Sound - EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content. FLASHBK EZ SOUND - When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Custom. - Normal, Stadium, News, Music, and Theater are preset for good sound quality at the factory and are not adjustable. EZ PIC EZ SOUND ADJUST SAP FREEZE APM Press the EZ SOUND button repeatedly to select the appropriate sound setup as shown below: Custom (your own settings), Normal, Stadium, News, Music, and Theater. • You can also adjust EZ Sound in the AUDIO menu. Press EXIT button to save and return to TV viewing. Manual Sound Control (EZ Sound-Custom option) SETUP VIDEO AUDIO TIME OPTION LOCK Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU SETUP VIDEO 80 80 AUDIO 0F TIME OPTION LOCK Previous - Adjust the sound to suit your taste and room situations. Balance Press the MENU button and then use AUDIO menu. Press the G button and then use D / E button to select the desired sound option (Balance, Treble, or Bass). Press the G button and then use adjustments. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. D / E F / G button to select the button to make appropriate 41 Operation Audio Menu Options continued Stereo/SAP Broadcasts Setup - This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one. - When having selected Stereo or SAP button on the remote control, this TV can only receive the signal in case that the TV station transmits the proper signals. - Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected. - Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting. - Stereo or SAP can be received in Analog channel. FLASHBK SAP EZ PIC EZ SOUND ADJUST SAP FREEZE APM Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono, Stereo, or SAP appear in turn. • If other languages available on the digital signal, select them with the SAP button. Press EXIT button to save and return to TV viewing. Front Surround SETUP VIDEO AUDIO TIME OPTION Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE SETUP VIDEO 50 50 AUDIO TIME OPTION LOCK LOCK Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Off 3D EchoSound System SRS TruSurround XT Previous is a trademark of SRS Press the MENU button and then use AUDIO menu. - TruSurround XT technology is incorporated under license from SRS Labs, Inc. Press the Press the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Labs, Inc. - Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. button and then use D / E D / E button to select the button to select Front Surround. G button and then use D / E button to select Off, 3D EchoSound System or SRS (Sound Retrieval System) TruSurround XT. Mini Glossary SRS TruSurround XT Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material. 3D EchoSound System Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage from stereo sound. 42 Operation TV Speakers On/Off Setup SETUP VIDEO AUDIO TIME OPTION Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE SETUP VIDEO 50 50 AUDIO TIME OPTION LOCK LOCK - Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off. Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Off On Previous Press the MENU button and then use AUDIO menu. Press the button and then use D /E button to select TV Speaker. Press the button and then use D /E button to select Off or On. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. button to select the D / E BBE SETUP VIDEO AUDIO TIME OPTION Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE SETUP VIDEO 50 50 AUDIO TIME OPTION LOCK - BBE High Definition Sound restores clarity and presence for better speech intelligibility and music realism. LOCK Audio Language EZ SoundRite EZ Sound Balance Treble Bass Front Surround TV Speaker BBE MENU Off On Previous Press the MENU button and then use AUDIO menu. Press the button and then use D /E button to select BBE. Press the button and then use D /E button to select Off or On. D / E button to select the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. • Manufactured under license from BBE Sound, Inc. • Treble, Bass or BBE aren’t suitable for SRS TSXT mode. 43 Operation T ime Menu Options Auto Clock Setup SETUP VIDEO AUDIO TIME Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off SETUP VIDEO AUDIO Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off Off On Time Zone Eastern Daylight Saving Auto TIME OPTION OPTION LOCK LOCK - The time is set automatically from a digital channel signal. - The digital channel signal includes information for the current time provided by the broadcasting station. MENU Previous Press the button and then use D /E button to select Auto Clock. Press the button and then use D /E button to select On. Press the G button and then use D / E button to select your viewing area time zone. • U.S.A: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii. • Canada: Eastern, Central, Mountain, Pacific, Nfld, or Atlantic. Press the G button and then use D / E button to select Auto, Off, On, depending on whether or not your viewing area observes Daylight Saving time. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. - Set the clock manually, if the current time is set incorrectly by the auto clock function. Press the MENU button and then use D / E button to select the TIME menu. Manual Clock Setup SETUP VIDEO AUDIO TIME Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off VIDEO AUDIO Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off Year Date Time --- ---/ -: -- -- TIME OPTION OPTION LOCK LOCK - If current time setting is wrong, reset the clock manually. 44 SETUP MENU Previous Press the MENU button and then use D / E button to select the TIME menu. Press the Clock. button and then use D / E button to select Manual Press the G button and then use F / G button to select either the year, date, or time option. Once selected, use the D / E button to set the year, date, and time options. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Operation On/Off Timer Setup Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off SETUP VIDEO AUDIO TIME SETUP VIDEO AUDIO Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off TIME OPTION OPTION LOCK LOCK - Timer function operates only if current time has been set. - Off-Timer function overrides OnTimer function if they are set both set to the same time. - The TV must be in standby mode for the On-Timer to work. - If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode. MENU Off On Time Ch. Vol 6 : 30 AM TV 2-0 17 Previous Press the MENU button and then use D / E button to select the TIME menu. Press the G button and then use D / E button to select On. • To cancel On/Off Timer function, select Off. Press the button and then use D /E button to set the hour. Press the button and then use D /E button to set the minutes. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Press the button and then use D /E button to select Off Timer or On Timer. For only On Timer function Press the G button and then use D / E button to select the channel at turn-on. Press the G button and then use D / E button to set the sound level at turn-on. Sleep Timer - The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. - You can also set up the Sleep Timer in the TIME menu. DAY - DAY+ MENU GUIDE Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. When the number of minutes you want is displayed on the screen, press the TIMER button. The timer begins to count down from the number of minutes selected. To check the remaining minutes before the TV turns off, press the TIMER button once. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off. RATIO ENTER TIMER EXIT TIMER CC INFO PAGE 45 Operation T ime Menu Options continued Auto Off SETUP VIDEO AUDIO TIME Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off VIDEO AUDIO Auto Clock Manual Clock Off Timer On Timer Sleep Timer Auto Off TIME OPTION OPTION LOCK LOCK - If set to on and there is no input signal, the TV turns off automatically after 10 minutes. 46 SETUP MENU If set to On and there is no input signal, the TV turns off automatically after 10 minutes. Off On Previous Press the MENU button and then use D / E button to select the TIME menu. Press the button and then use D /E button to select Auto Off. Press the button and then use D /E button to select Off or On. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Operation Option Menu Features Aspect Ratio Control - Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed. - If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option. - Horizon aspect ratio is not available for Component 1-2 (480p/720p/1080i) /RGB-DTV (480p/720p/1080i)/HDMI/DVIDTV (720p/1080i) /DTV(720p/1080i) input source. - In RGB-PC/DVI-PC input source, only either 4:3 or 16:9 aspect ratio is available. - If a fixed image is displayed on the screen for a long time, the image may become imprinted on the screen and remain visible. INPUT TV POWER TV AUDIO DVD VCR MODE CABLE STB GUIDE RRAATTIOIO DAY - MENU Press the RATIO button repeatedly to select the desired picture format. • You can also adjust Aspect Ratio in the OPTION menu. • Set By Program Selects the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9) • 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with gray bars appearing at both the left and right sides. • 16:9 Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. • Horizon Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a panorama view. • Zoom 1 Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. • Zoom 2 Choose Zoom 2 when you want the picture to be altered, both horizontally extended and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage. • Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted. You can adjust the enlarge proportion of Cinema Zoom using D / E button. The adjustment range is 1~16. DAY+ ENTER EXIT TIMER CC INFO 47 Operation Option Menu Features continued Cinema 3:2 Mode Setup SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power Off On OPTION LOCK LOCK MENU Previous - Most movies are 24 frames/sec, but TV signal is 30 frames/sec. - This option lets the TV do 3:2 pull-down operation for you to watch movies at the best motion appearance. Press the G button and then use D / E button to select Cinema 3:2 Mode. Press the - This feature operates only in AV1, AV2, Component 480i mode. Press the MENU button and then use D / E button to select the OPTION menu. button and then use D /E button to select Off or On. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Caption SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME Off On OPTION LOCK 48 Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power LOCK MENU Previous Press the MENU button and then use OPTION menu. Press the button and then use D /E button to select Caption. Press the button and then use D /E button to select Off or On. D / E button to select the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Operation Caption/Text * Analog Broadcasting System Captions SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power OPTION LOCK LOCK - Select a caption mode for displaying captioning information if provided on a program. - Analog caption displays information at any position on the screen. - Text displays information, usually at the bottom position and is used for a data service. - Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. - This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off. MENU CC 1 CC 2 CC 3 CC 4 Text 1 Text 2 Text 3 Text 4 Previous Use the CC button repeatedly to select Caption Off, CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. Press EXIT button to save and return to TV viewing. Press the MENU button and then use OPTION menu. Press the G button and then use D /E D / E button to select the button to select Caption/Text. Press the G button and then use D / E button to select caption: CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. • CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. • TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. * Digital Broadcasting System Captions SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME LOCK LOCK - Other languages can be chosen for digital sources only if they are included on the program. English Spanish French OPTION - Choose the language you want the DTV/CADTV Captions to appear in. Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power MENU Previous Press the MENU button and then use OPTION menu. Press the G button and then use D /E D / E button to select the button to select Caption/Text. Press the G button and then use D / E button to select available caption languages: English, Spanish, or French. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 49 Operation Option Menu Features continued Caption Option SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power Style Size Font Text Color OPTION LOCK LOCK - Customize the DTV/CADTV captions that appear on your screen. MENU Custom A Standard Font 0 White Text Opacity Bg Color Bg Opacity Edge Type Edge Color Solid Black Solid None Black Previous Press the MENU button and then use OPTION menu. Press the G button and then use D Press the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. button and then use D / E button to select the / E button to select Caption Option. F /G button to select Custom. Use D / E button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language. • Size: Set the size the words will appear in. • Font: Select a typeface for the words. • Text Color: Choose a color for the text. • Text Opacity: Specify the opacity for the text color. • Bg (Background) Color: Select a background color. • Bg (Background) Opacity: Select the opacity for the background color. • Edge Type: Select an edge type. • Edge Color: Select a color for the edges. Low Power (42PC3D/3DV, 50PC3D only) SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME OPTION LOCK - Low power reduces the power consumption of plasma display. 50 Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power LOCK MENU Off On Previous Press the MENU button and then use OPTION menu. Press the button and then use D /E button to select Low Power. Press the button and then use D /E button On or Off. D / E button to select the Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Operation ISM (Image Sticking Minimization) Method (42PC3D/3DV, 50PC3D only) SETUP VIDEO AUDIO TIME OPTION Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power SETUP VIDEO AUDIO TIME OPTION LOCK - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image ; even though the image is changed. Use our unique method to minimize any fixed image on the screen. Aspect Ratio Cinema 3:2 Mode Caption Caption/Text Caption Option Language ISM Method Low Power LOCK MENU Previous Normal White Wash Orbiter Inversion Press the MENU button and then use OPTION menu. Press the Press the button and then use D /E button and then use D / E button to select the button to select ISM Method. D / E button to select Normal, White Wash, Orbiter or Inversion. • Normal If image sticking is never a problem, ISM is not necessary - set to Normal. • White Wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. • Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move once per 2 minutes: Left → Right → Upside → Downside → Right → Left → Downside → Upside. • Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 51 Operation Lock Menu Options Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only. For USA Ratings for Movies previously shown in theaters: Movie Ratings : • Blocking Off (Permits all programs) •G (General audience) • PG (Parental guidance suggested) • PG-13 (Parents strongly cautioned) •R (Restricted) • NC-17 (No one 17 and under admitted) •X (Adult only) If you set PG-13 : G and PG movies will be available, PG-13, R, NC-17 and X will be blocked. Ratings for Television programs including made-for-TV movies : • TV-G • TV-PG • TV-14 • TV-MA • TV-Y • TV-Y7 (General audience) (Parental guidance suggested) (Parents strongly cautioned) (Mature audience only) (All children) (Children 7 years older) TV Rating-Children: • Age • Fantasy Violence (applies to TV-Y, TV-Y7) (applies to TV-Y7) TV Rating-General: • Age (applies to TV-G, TV-PG, TV-14, TV-MA) • Dialogue- sexual dialogue (applies to TV-PG, TV-14) • Language- adult language (applies to TV-PG, TV14, TV-MA) • Sex- sexual situations (applies to TV-PG, TV-14, TV-MA) • Violence (applies to TV-PG, TV-14, TV-MA) Input Block • Video, Front Video • Component 1, 2 • RGB, HDMI/DVI 52 (On, Off) (On, Off) (On, Off) For Canada TV Rating-English: •E (Exempt) •C (Children) • C8+ (8 years and up) •G (General programming. Suitable for all audiences) • PG (Parental guidance suggested) • 14+ (Viewers 14 years and up) • 18+ (Adult programming) • Blocking off (Permits all programming) TV Rating-French: •E (Exempt) •G (General) • 8 ans+ (8 years and up) • 13 ans+ (13 years and up) • 16 ans+ (16 years and up) • 18 ans+ (Adults only) • Blocking off (Permits all programming) Input Block • Video 1, 2 • Component 1, 2 • RGB and HDMI/DVI (On, Off) (On, Off) (On, Off) Operation Parental Lock Setup * For U.S.A. SETUP VIDEO AUDIO TIME SETUP Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Input Block VIDEO AUDIO TIME OPTION OPTION LOCK LOCK * For Canada SETUP VIDEO AUDIO Lock System Set Password Block Channel TV Rating-English TV Rating-French Input Block SETUP VIDEO AUDIO TIME OPTION OPTION LOCK LOCK - A password is required to gain access to this menu if the Lock System is turned on. MENU Off On Previous Enter Password TIME - Set up blocking schemes to block specific channels, ratings, and external viewing sources. Lock System Set Password Block Channel Movie Rating TV Rating-Children TV Rating-General Input Block Lock System Set Password Block Channel TV Rating-English TV Rating-French Input Block MENU Off On Previous Press the MENU button and then use D / E button to select the LOCK menu. Then, press the G button • If Lock is already set, enter the password as requested. • The TV is set up with the initial password “0-0-0-0”. Use the D / E button to choose from the following Lock Menu options. Once the option is selected, change the settings to your preference. • Lock System: Activates or disables the blocking scheme you set up previously. • Set Password: Change the password by inputting a new password twice. • Block Channel.: Select a channel number that you wish to block. • Input block: Enables you to select a source to block from the external source devices you have hooked up. W For USA • Movie Rating (MPPA): Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. • TV Rating-Children: Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. • If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control. Then, the password reset to ‘7’, ‘7’, ‘7’, ‘7’. • TV Rating-General: Based on the ratings, blocks certain TV programs that you and your family do not want to view. W For Canada • TV Rating-English / TV Rating-French: Selecting canadian English /French language rating system. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 53 Reference External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the TV back panel. - RS-232C connection cables are not supplied with the TV. RS-232C Setup HDMI/DVI HDMI/D VI IN DIGITAL AUDIO OUT OPTICAL RS-232C IN (CONTROL & SER (CONTROL SERVICE) VICE) PC Type of Connector; D-Sub 9-Pin Male No. Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations 3-Wire Configurations (Not standard) 7-Wire Configurations (Serial female-female NULL modem cable) RXD TXD GND DTR DSR RTS CTS 54 PC TV D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC TV D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Reference Set ID - Use this function to specify a TV ID number. - Refer to ‘Real Data Mapping’. See page 56. SETUP VIDEO 1. Press the MENU button and then use SETUP menu. 2. Press the G button and then use D /E D /E button to select the AUDIO button to select Set ID. TIME 3. Press the G button and then use D / E button to adjust Set ID to choose the desired TV ID number. The adjustment range of Set ID is 1 ~ 99. EZ Scan Manual Scan Channel Edit DTV Signal Input Source Input Label Set ID OPTION LOCK MENU Previous 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Communication Parameters • • • • • Baud rate : 9600 bps (UART) Data length : 8 bits Parity : None Stop bit : 1 bit Communication code : ASCII code Transmission / Receiving Protocol Transmission * Use a crossed (reverse) cable. [Command1][Command2][ ][Set ID][ ][Data][Cr] Command Reference List COMMAND 1 COMMAND 2 DATA (Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode 14. Treble 15. Bass 16. Balance 17. Color Temperature 18. ISM Method 19. Low Power 20. Orbiter Time Setting 21. Orbiter Pixel Setting 0~1 0~8 * (Refer to p.56) 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0~2 * (Refer to p.58) 0~1 1 ~ FE 1 ~3 * Command 18~21: 42PC3D/3DV, 50PC3D models only COMMAND 1 22. Channel Tuning 23. Channel Add/Del 24. Key 25. Input Select COMMAND 2 * [Command 1]: First command to control the set.(j,k,m or x) * [Command 2]: Second command to control the set. * [Set ID]: You can adjust the set ID to choose desired monitor ID number in Setup menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. * [DATA]: To transmit command data. Transmit ‘FF’ data to read status of command. * [Cr]: Carriage Return ASCII code ‘0x0D’ * [ ]: ASCII code ‘space (0x20)’ OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time DATA 0 DATA 1 (Hexadecimal) (Hexadecimal) physical/program high major/program low DATA 2 DATA 3 DATA 4 (Hexadecimal) (Hexadecimal) (Hexadecimal) major low minor high minor low DATA 5 (Hexadecimal) attribute 00 ~ 01 key code *(Refer to p.59) 55 Reference 01. Power (Command2:a) 05. Volume Mute (Command2:e) G To control Power On/Off of the Monitor. G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume mute off (Volume on) 1 : Volume mute on (Volume off) [a][ ][Set ID][ ][OK][Data][x] * In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function. Acknowledgement [e][ ][Set ID][ ][OK][Data][x] 06. Volume Control (Command2:f) G To select input source for the Monitor. G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission Transmission [k][b][ ][Set ID][ ][Data][Cr] [k][f][ ][Set ID][ ][Data][Cr] 02. Input Select (Command2:b) (Main Picture Input) Data 0: DTV 1: Analog 2: AV1 3: AV2 4: Component 1 5: 6: 7: 8: Component 2 RGB-DTV RGB-PC HDMI/DVI Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’ as shown below. Acknowledgement [f][ ][Set ID][ ][OK][Data][x] Acknowledgement 07. Contrast (Command2:g) [b][ ][Set ID][ ][OK][Data][x] G To adjust screen contrast. You can also adjust contrast in the Video menu. Transmission 03. Aspect Ratio (Command2:c) (Main picture format) [k][g][ ][Set ID][ ][Data][Cr] G To adjust the screen format. You can also adjust the screen format using the RATIO button on remote control or in the Option menu. Transmission Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’ as shown below. [g][ ][Set ID][ ][OK][Data][x] [k][c][ ][Set ID][ ][Data][Cr] Date 1: 2: 3: 4: 5: 4:3 16:9 Horizon Zoom 1 Zoom 2 Acknowledgement 6: Set by program 10: Cinema Zoom (1) 1F: Cinema Zoom (16) Acknowledgement [c][ ][Set ID][ ][OK][Data][x] 08. Brightness (Command2:h) G To adjust screen brightness. You can also adjust brightness in the Video menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’ as shown below. Acknowledgement [h][ ][Set ID][ ][OK][Data][x] 04. Screen Mute (Command2:d) G To select screen mute on/off. * Real data mapping Transmission 0 : Step 0 [k][d][ ][Set ID][ ][Data][Cr] A : Step 10 (SET ID 10) Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement [d][ ][Set ID][ ][OK][Data][x] F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 63 : Step 99 (SET ID 99) 64 : Step 100 * Tint : R50 ~ G50 * Balance : L50 ~ R50 56 Reference 09. Color (Command2:i) 13. Remote Control Lock Mode (Command2:m) G To adjust the screen color. You can also adjust color in the Video menu. G To lock the remote control and the front panel controls on the set. Transmission Transmission [k][i][ ][Set ID][ ][Data][Cr] [k][m][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping’. See page 56. Acknowledgement Data 0: Lock off 1: Lock on Acknowledgement [m][ ][Set ID][ ][OK][Data][x] [i][ ][Set ID][ ][OK][Data][x] 14. Treble (Command2:r) 10. Tint (Command2:j) G To adjust treble. You can also adjust treble in the Audio menu. G To adjust the screen tint. You can also adjust tint in the Video menu. Transmission [k][r][ ][Set ID][ ][Data][Cr] Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 0 ~ Green : 64 • Refer to ‘Real data mapping’. See page 56. Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 56. Acknowledgement [r][ ][Set ID][ ][OK][Data][x] Acknowledgement [ j ][ ][Set ID][ ][OK][Data][x] 15. Bass (Command2:s) G To adjust bass. You can also adjust bass in the Audio menu. Transmission 11. Sharpness (Command2:k) [k][s][ ][Set ID][ ][Data][Cr] G To adjust the screen sharpness. You can also adjust sharpness in the Video menu. Transmission Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 56. Acknowledgement [k][k][ ][Set ID][ ][Data][Cr] [s][ ][Set ID][ ][OK][Data][x] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 56. Acknowledgement 16. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Audio menu. [k][ ][Set ID][ ][OK][Data][x] Transmission [k][t][ ][Set ID][ ][Data][Cr] 12. OSD Select (Command2:l) G To select OSD (On Screen Display) on/off. Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping’. See page 56. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] Transmission [k][l][ ][Set ID][ ][Data][Cr] Data 0: OSD off Acknowledgement [l][ ][Set ID][ ][OK][Data][x] 1: OSD on 17. Color Temperature (Command2:u) G To adjust color temperature. You can also adjust color temperature in the Video menu. Transmission [k][u][ ][Set ID][ ][Data][Cr] Data 0: Medium 1: Cool 2: Warm Acknowledgement [u][ ][Set ID][ ][OK][Data][x] 57 Reference 18. ISM Method (Command2:p) 22. Tune Command (Command: m a) G To avoid having a fixed image remain on screen. G To tune channel to following physical/major/minor number Transmission Transmission [ j ][p][ ][Set ID][ ][Data][Cr] [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr] Data 1: Inversion 2: Orbiter 4: White Wash 8: Normal Acknowledgement [p][ ][Set ID][ ][OK][Data][x] 19. Low Power (Command2:q) G To control the Low Power function on/off. You can also adjust Low Power in Option menu. Data 0: Physical Channel Number(Transmit by Hexadecimal code) NTSC air:02~45 NTSC cable: 01, 0E~7D ATSC air:01~45 ATSC cable:01~87 Data 1,Data 2: Major Channel Number(two part) or Channel Number(One part) Data1: High byte Data2: Low byte Two part channel number: Major number-Minor number One part channel number: If the channel band is ATSC digital cable, it can be used. In case of using one part channel number, minor channel does not need. Data 3, Data 4: Minor Channel Number Data3: High byte Data4: Low byte Data 5: Transmission Main Picture [ j ][q][ ][Set ID][ ][Data][Cr] Main Data 0: Low Power off 1: Low Power on Acknowledgement Two/One Part Channel Two One 1 No Use 20. Orbiter Time Setting (Command2:r) Transmission [ j ][r][ ][Set ID][ ][Data][Cr] Data Min: 1 ~ Max: FE Acknowledgement [r][ ][Set ID][ ][OK][Data][x] 21. Orbiter Pixel Setting (Command2:s) G To adjust pixel number in orbiter function. Transmission [ j ][s][ ][Set ID][ ][Data][Cr] Data Min: 1 ~ Max: 3 Acknowledgement [s][ ][Set ID][ ][OK][Data][x] Use [q][ ][Set ID][ ][OK][Data][x] G To adjust orbiter operation time term. Using 5 Physical Reserv Channel ed Step 1 NTSC Cable ATSC Air ATSC Cable_std ATSC Cable_hrc ATSC Cable_irc ATSC cable_auto NTSC Air ... Reserved Reserved * All data are transmitted by Hexadecimal code *Two/One part Channel: 6th bit This bit is used in a cable-ready system. *Using physical channel: 5th bit If the channel band is NTSC air or NTSC cable, channel tuning can be done by only physical channel. In this case, using physical channel bit must be low(0). But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1). Example) 1. Analog channel: NTSC cable, channel number(35), main picture Command: ma 00 23 xx xx xx xx 01attribute(0x01): main picture, two part(it’s not mandatory), using physical channel, NTSC cable ‘xx’ data: don’t care major and minor channel number in case analog channel tuning. 2. Digital channel: ATSC air, channel number(don’t know physical channel, major(30), minor(3)), main picture Command: ma 00 xx 00 1E 00 03 22 attribute(0x22): main picture, two part, not using physical channel, ATSC air ‘xx’ data: don’t care analog channel number in case digital channel tuning. 3. Digital channel: ATSC air, channel number (physical(20), major (30), minor (5)), main picture Command: ma 00 14 00 1E 00 05 02 attribute(0x02): main picture, two part, using physical channel, ATSC air. Acknowledgement [a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][Data5][x] [a][ ][Set ID][ ][NG][Data0][x] 58 Reference 23. Channel Add/Del (Command: m b) G To add and delete the channels Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 0: Channel Delete 1: Channel Add Acknowledgement [b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x] 24. Key (Command: m c) G To send IR remote key code Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code: Refer to page 61. Acknowledgement [c][ ][Set ID][ ][OK][Data][x] 25. Input select(Command: x b) (Main Picture Input) G To select input source for TV. Transmission [x][b][][Set ID][][Data][Cr] Data Structure DATA(Hex) INPUT 00 DTV (Antenna) 01 DTV (Cable) 10 Analog (Antenna) 11 Analog (Cable) 20 Video 21 Front Video 40 Component 1 41 Component 2 50 RGB DTV 60 RGB PC 90 HDMI/DVI Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x] 59 Reference IR Codes How to Connect G Connect your wired remote control to the Remote Control port on the TV. Remote Control IR Codes G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 G Configuration of frame • 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 • Repeat frame Repeat code Tf G Lead code 9 ms 4.5 ms 0.55 ms G Repeat code 9 ms 2.25 ms G Bit description • Bit “0” • Bit “1” 0.56 ms 0.56 ms 1.12 ms 2.24 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz 60 Reference Code (Hexa) 0B 0F 08 C4 C5 79 0E 10 ~ 19 4C 1A 09 02 03 00 01 1E AA 39 40 41 07 06 44 43 A9 52 4D 5B 65 0A CB D6 5A D0 BF D4 D5 D7 C6 76 77 AF 98 Function INPUT TV POWER POWER ON POWER OFF RATIO TIMER Number Key 0~ 9 - (Dash) FLASHBK MUTE VOL D VOLE CH D CH E FAV INFO CC ENTER MENU GUIDE EZ SOUND EZ PIC EXIT FREEZE SAP ADJUST TV VIDEO Front Video COMPONENT 1 COMPONENT 2 RGB-PC RGB-DTV HDMI/DVI Ratio 4:3 Ratio 16:9 Ratio Zoom MULTIMEDIA Note R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (Video Input Selection) Discrete IR Code (Front Video Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (RGB-DTV Input Selection) Discrete IR Code (HDMI/DVI Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) Discrete IR Code (Multmedia Selection) 61 Reference Programming the Remote G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable devices of other manufacturers. Note that the remote control may not control all models of other brands. Programming a code into a remote mode Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding MODE button (VCR) on the remote control, while illuminating on the selected component. Test the POWER button to see if the component responds properly. If not, the remote requires programming to operate the device. Turn on the component to be programmed, then press the corresponding MODE button on the remote control. Press the MENU and MUTE buttons simultaneously for 2 seconds, the button selected component lights on the remote control. If you don't press any button for 20 seconds, the button selected component will turn off on the remote control. At a moment, you have to repeat from step 2. Enter a code number using the number buttons on the remote. When pressing the button, the light is blinked at a time. Programming code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device will turn off. Press the MENU button to store the code. After blinking twice, this code is stored. Test the remote control functions to see if the component responds properly. If not, repeat from step 2. INPUT TV POWER DVD TV AUDIO VCR MODE CABLE STB DAY - MENU DAY+ GUIDE RATIO ENTER EXIT TIMER CC INFO PAGE VOL FAV MUTE CH PAGE FLASHBK EZ PIC EZ SOUND ADJUST 62 APM SAP FREEZE Reference Programming Codes VCRs Brand Codes Brand Codes Brand Codes Brand Codes AIWA AKAI 034 016 125 072 031 012 035 028 108 003 031 005 065 112 108 012 034 059 006 029 036 129 003 034 031 107 132 012 004 043 031 031 012 040 043 012 048 130 KENWOOD 014 047 001 101 034 003 017 040 031 067 012 069 101 027 031 003 033 101 045 013 013 049 151 034 024 012 048 043 053 066 133 013 063 031 031 067 101 013 PORTLAND PULSAR QUARTZ QUASAR RCA 108 072 011 033 013 040 107 145 003 031 053 058 148 014 032 105 113 125 022 003 102 017 131 003 013 031 101 031 024 003 056 077 034 013 031 067 034 010 TATUNG TEAC TECHNICS TEKNIKA 039 034 031 019 101 034 006 008 059 040 040 012 048 012 040 003 031 053 012 034 058 AMPRO ANAM AUDIO DYNAMICS BROKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO HARMAN KARDON HITACHI INSTANTREPLAY JCL JCPENNY JENSEN JVC 043 046 124 146 033 023 037 031 103 039 043 129 033 040 033 007 108 116 135 041 010 064 110 111 117 119 023 039 043 053 027 035 101 153 010 LG (GOLDSTAR) LLOYD LXI MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI 017 031 037 131 008 025 034 046 138 009 033 109 136 045 018 063 033 033 013 066 063 072 144 147 MTC MULTITECH NEC 026 034 137 150 NORDMENDE OPTONICA PANASONIC PENTAX 015 033 101 031 033 043 050 055 060 150 152 PHILCO PHILIPS PILOT PIONEER 034 039 043 048 012 013 020 106 114 123 009 013 014 034 101 106 033 034 041 068 031 033 067 030 033 010 034 102 046 020 020 051 REALISTIC RICO RUNCO SALORA SAMSUNG 014 031 053 072 134 139 059 045 046 059 061 040 034 023 039 043 054 070 074 083 140 145 020 031 033 034 067 033 034 054 071 101 021 048 SANSUI SANYO SCOTT SEARS SHARP SHINTOM SONY SOUNDESIGN STS SYLVANIA SYMPHONIC TANDY 014 066 020 041 109 147 008 033 054 075 033 062 140 145 034 063 144 010 014 034 040 101 THOMAS TMK TOSHIBA TOTEVISION UNITECH VECTOR RESEARCH 040 102 104 107 109 112 115 120 122 043 048 135 007 010 014 134 037 112 129 VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA ZENITH 043 039 043 033 070 031 033 034 013 042 047 082 112 131 101 034 046 013 033 054 034 048 072 017 034 131 039 056 080 024 040 043 101 008 009 010 014 017 020 042 073 081 054 149 009 031 052 057 058 076 078 149 033 034 059 034 Cable Box Brand Codes Brand Codes ABC 003 046 112 014 005 026 092 007 007 065 080 019 023 020 057 032 072 008 052 GOLDEN CHANNEL HAMLIN HITACHI HOSPITALITY JERROLD 030 049 052 070 002 009 074 001 037 033 010 100 028 015 073 016 044 100 006 AJIN ANTRONIK ARCHER CABLE STAR CENTURION CENTURY CITIZEN COLOUR VOICE COMBANO COMTRONICS DIAMOND EAGLE EASTERN ELECTRICORD GE GEMINI GI 004 039 042 052 053 007 014 024 090 081 030 030 040 062 066 022 025 054 074 LG (GOLDSTAR) M-NET MACOM MAGNAVOX MEMOREX MOVIE TIME NSC OAK PANASONIC PARAGON PHILIPS 050 055 055 077 003 004 008 010 052 069 106 101 005 012 064 079 032 028 038 071 031 037 053 047 012 013 020 Brand PIONEER POST NEWS WEEK PRUCER PTS PULSAR RCA REGAL REGENCY REMBRANT SAMSUNG SCIENTIFIC ATLANTA SHERITECH SIGNAL SIGNATURE SL MARX Codes Brand Codes 065 034 076 016 059 011 073 100 047 049 057 025 102 003 043 022 030 052 030 SPRUCER STARCOM STARGATE TADIRAN TAEKWANG TAIHAN TANDY TEXSCAN TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL 047 002 008 030 110 105 017 029 039 100 007 004 005 026 012 087 100 085 090 051 052 063 048 071 072 074 050 107 030 068 011 041 042 045 046 VIEWSTAR ZENITH 078 004 008 009 030 040 056 014 053 007 027 015 088 114 024 014 032 018 089 060 024 035 086 093 63 Reference Digital Cable/Satellite Box Brand Codes Brand ALPHASTAR DSR AMPLICA BIRDVIEW CHANNEL MASTER 123 050 051 013 036 008 054 050 005 011 141 024 038 093 097 122 089 114 017 133 GENERAL INSTRUMENT 003 031 HITACHI 139 HOUSTON TRACKER 033 057 HUGHES 068 JANIEL 060 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 MACOM 010 065 MEMOREX 057 NEXTWAVE 028 NORSAT 069 CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME EUROPLUS FUJITSU 126 129 014 015 018 055 009 012 077 145 006 007 010 052 112 116 046 040 094 098 056 057 095 099 076 058 096 100 021 022 027 Codes Brand 134 004 016 029 059 101 140 037 039 051 104 147 144 059 063 064 124 125 070 Codes 143 PANASONIC 060 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 PRIMESTAR 030 PROSAT 072 RCA 066 REALISTIC 043 SAMSUNG 123 SATELLITE SERVICE CO 028 085 SCIENTIFIC ATLANTA 032 SONY 103 STARCAST 041 SUPER GUIDE 020 TEECOM 023 Brand PACE SKY SATELLITE 142 TOSHIBA UNIDEN 102 110 111 UNIDEN VIEWSTAR WINEGARD ZENITH 106 074 Codes 088 137 002 016 044 078 101 135 115 128 081 091 090 107 130 127 025 042 043 045 048 049 079 080 086 136 146 082 083 084 120 035 047 057 138 124 125 026 075 087 Audio Brand AIWA Codes 014 125 230 AKAI 163 ANAM 003 059 217 BURMECTER 252 CARVER 086 CLARION 199 DAEWOO 027 102 DENON 015 FANTASIA 071 FINEARTS 022 FISHER 089 LG(GOLDSTAR) 001 087 190 211 HAITAI 034 HARMAN/KARDON 068 INKEL 037 078 122 152 157 189 225 247 028 070 096 129 139 229 014 017 023 106 189 216 235 236 Brand Codes JVC KEC KENWOOD 004 185 038 170 215 030 045 014 100 175 179 201 214 238 103 111 002 034 097 049 104 107 046 013 048 133 158 007 142 104 KOHEL NAD LOTTE 053 060 084 148 198 221 075 130 143 099 021 107 191 212 035 024 108 192 239 188 029 110 210 058 079 149 153 158 207 226 062 095 150 154 159 222 227 069 121 151 155 160 224 243 222 LXI MAGNAVOX MARANTZ MCINTOSH MCS MEMOREX NAD ONKYO OPTIMUS PANASONIC PENNEY 013 186 050 171 222 046 016 172 176 180 202 219 240 141 187 067 089 197 206 036 173 177 181 208 223 098 174 178 183 213 232 018 020 025 041 081 090 112 Brand Codes PHILIPS PIONEER 026 039 065 115 113 080 092 103 124 193 204 011 019 106 031 072 156 206 005 044 118 012 076 162 166 205 010 185 101 147 QUASAR RCA RCX REALISTIC SAMSUNG SANSUI SANYO SCOTT SHARP SHERWOOD SONY TAEKWANG 040 041 047 056 057 132 140 TEAC 033 064 113 220 241 251 TECHNICS 112 042 091 123 106 145 194 244 135 083 186 032 082 184 209 006 045 126 020 077 163 167 231 085 187 113 218 143 043 063 093 094 127 250 146 195 245 138 234 Brand Codes TOSHIBA THE VICTOR WARDS YAMAHA 137 061 088 131 089 054 055 066 092 199 182 203 246 144 051 052 117 119 199 200 158 109 248 073 105 164 168 233 106 237 128 114 249 074 161 165 169 242 136 134 DVD Brand Codes Brand Codes Brand Codes Brand Codes APEX DIGITAL DENON GE HARMAN KARDON JVC LG 022 020 014 005 006 027 012 001 010 016 025 MAGNAVOX MARANTZ MITSUBISHI NAD ONKYO PANASONIC 013 024 002 023 008 017 003 009 PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG 013 004 021 005 005 011 SONY THOMPSON TOSHIBA YAMAHA ZENITH 007 005 019 009 010 64 026 006 006 015 006 008 018 016 025 Reference Troubleshooting Checklist The operation does not work normally. The remote control doesn’t work • Check to see if there is any object between the product and the remote control causing obstruction. • Are batteries installed with correct polarity (+ to +, - to -)? • Correct remote operating mode set: TV, VCR etc.? • Install new batteries. Power is suddenly turned off • Is the sleep timer set? • Check the power control settings. Power interrupted • No broadcast on station tuned with Auto off activated. The video function does not work. No picture & No sound • Check whether the product is turned on. • Try another channel. The problem may be with the broadcast. • Is the power cord inserted into wall power outlet? • Check your antenna direction and/or location. • Test the wall power outlet, plug another product’s power cord into the outlet where the product’s power cord was plugged in. Picture appears slowly after switching on • This is normal, the image is muted during the product startup process. Please contact your service center, if the picture has not appeared after five minutes. No or poor color or poor picture • Adjust Color in menu option. • Keep a sufficient distance between the product and the VCR. • Try another channel. The problem may be with the broadcast. • Are the video cables installed properly? • Activate any function to restore the brightness of the picture. Horizontal/vertical bars or picture shaking • Check for local interference such as an electrical appliance or power tool. Poor reception on some channels Lines or streaks in pictures • Station or cable product experiencing problems, tune to another station. • Station signal is weak, reorient antenna to receive weaker station. • Check for sources of possible interference. • Check antenna (Change the direction of the antenna). 65 Reference The audio function does not work. Picture OK & No sound No output from one of the speakers Unusual sound from inside the product • Press the VOL or VOLUME button. • Sound muted? Press MUTE button. • Try another channel. The problem may be with the broadcast. • Are the audio cables installed properly? • Adjust Balance in menu option. • A change in ambient humidity or temperature may result in an unusual noise when the product is turned on or off and does not indicate a fault with the product. There is a problem in PC mode. (Only PC mode applied) The signal is out of range. • Adjust resolution, horizontal frequency, or vertical frequency. • Check it whether the signal cable is connected or loose. • Check the input source. Vertical bar or stripe on background & Horizontal Noise & Incorrect position • Work the Auto configure or adjust clock, phase, or H/V position. (Option) Screen color is unstable or single color 66 • Check the signal cable. • Reinstall the PC video card. Reference Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Product Specifications MODEL Power requirement 32LC2D 37LC2D 42LC2D AC100-240V ~ 50/60Hz 1.5A AC100-240V ~ 50/60Hz 2.0A AC100-240V ~ 50/60Hz 2.5A Television System NTSC-M, ATSC, 64 & 256 QAM Program Coverage VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69 External Antenna Impedance 75 Ω Operating Temperature Range 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% MODEL 42PC3D/3DV-UD 50PC3D-UD Power requirement AC100-240V ~ 50/60Hz 2.0A Television System NTSC-M, ATSC, 64 & 256 QAM Program Coverage VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135, DTV 2 ~ 69 External Antenna Impedance 75 Ω Operating Temperature Range 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% Resolution 852 x 480 (Dot) 1366 x 768 (Dot) • The specifications shown above may be changed without prior notice for quality improvement. 67
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No Page Count : 43 PDF Version : 1.6 Has XFA : No XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:77304d7a-9702-4c47-ae4b-76b6c0185fb5 Modify Date : 2005:12:05 22:32:40+09:00 Create Date : 2005:12:05 22:32:32+09:00 Metadata Date : 2005:12:05 22:32:40+09:00 Document ID : uuid:3e0cbd28-fdb2-4995-81bd-15a4b898002b Format : application/pdf Title : 527A Creator : 3.3: LaserWriter 8 8.7.1 Author : sun Producer : Acrobat Distiller 4.0.5 for MacintoshEXIF Metadata provided by EXIF.tools