LG Electronics USA 50PK550UA PLASMA TV/MONITOR User Manual SAC33575901 Edit1 en
LG Electronics USA PLASMA TV/MONITOR SAC33575901 Edit1 en
Contents
- 1. User manual 1 of 2
- 2. User manual 2 of 2
User manual 1 of 2
PLASMA TV OWNER’S MANUAL 42PJ350 50PJ350 50PJ340 50PK250 60PK250 50PK540 60PK540 50PK550 60PK550 Please read this manual carefully before operating your set and retain it for future reference. The model and serial number of the TV is located on the back and one side of the TV. Record it below should you ever need service. Model: Serial: This product qualifies for ENERGY STAR in the “factory default (Home Use mode)” setting. Changing the factory default picture setting or enabling other features will increase power consumption that could exceed the limits necessary to quality for Energy Star rating. 1-800-243-0000 USA, Consumer User 1-888-865-3026 1-888-542-2623 USA, Commercial User CANADA LG Customer Information Center P/NO : SAC33575901(0905-REV06) www.lgusa.com / www.lg.ca www.lgusa.com / www.lg.ca / www.lgcommercial.com WARNING / CAUTION WARNING / CAUTION To prevent fire or shock hazards, do not expose this product to rain or moisture. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. NOTE TO CABLE/TV INSTALLER This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. FCC NOTICE Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause (harmful) interference, and (2) this device must accept any interference received, including interference that may cause undesired operation (of the device). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lighting storms or when unused for long periods of time. 10 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. SAFETY INSTRUCTIONS 11 Never touch this apparatus or antenna during a thunder or lighting storm. 12 When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV. 13 Do not allow an impact shock or any objects to fall into the product, and do not drop onto the screen with something. 14 CAUTION concerning the Power Cord: It is recommend that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. Do not make the TV with the power cord plugged in. Do not use a damaged or loose power cord. Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV. 15 WARNING - To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids. Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning. 16 Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g. on shelves above the unit). 17 GROUNDING Ensure that you connect the earth ground wire to prevent possible electric shock (i.e. a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker 18 DISCONNECTING DEVICE FROM MAINS Mains plug is the disconnecting device. The plug must remain readily operable. 19 "As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH" 20 ANTENNAS Outdoor antenna grounding If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70 Pince de mise à la terre 23 Ventilation Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the product with cloth or other materials (e.g.) plastic while plugged in. Do not install in excessively dusty places. 24 If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord contact an authorized service center. 25 Do not press strongly upon the panel with hand or sharp object such as nail, pencil or pen, or make a scratch on it. 26 Keep the product away from direct sunlight. Fil d entrée d antenne Décharge d antenne (section 810-20 du NEC) Conducteur mis à la terre (section 810-21 du NEC) Équipement électrique Pince de mise à la terre Système d électrode de mise à la terre (article 250, section H du NEC) NEC: National Electrical Code 21 Cleaning When cleaning, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene. 22 Moving Make sure the product is turned off, unplugged and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV. CONTENTS WARNING / CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FEATURE OF THIS TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 PREPARATION Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Front Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Stand Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Cable Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Desktop Pedestal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Swivel Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 VESA Wall Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Securing the TV to the wall to prevent falling when the TV is used on a stand . . . . . . . . . . . . . . . . . . . . . . . . 18 Antenna or Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . 19 USB Entry Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Photo List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Music List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 EXTERNAL EQUIPMENT SETUP PICTURE CONTROL HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Other A/V Source Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 USB Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Audio Out Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Picture Size (Aspect Ratio) Control . . . . . . . . . . . . . . . . . . 60 Picture Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Energy Saving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 Preset Picture Settings(Picture Mode) . . . . . . . . . . . . . . 65 Manual Picture Adjustment - User Mode . . . . . . . . . . 66 Picture Improvement Technology . . . . . . . . . . . . . . . . . . . . . 67 Expert Picture Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Picture Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Image Sticking Minimization (ISM) Method . . . . . . . 71 WATCHING TV / CHANNEL CONTROL Remote Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Initial Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 On-Screen Menus Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Quick Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Channel Setup - Auto Scan (Auto Tuning) . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 - Add / Delete Channel (Manual Tuning) . . . . . . 42 - Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Favorite Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Favorite Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Brief Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Input List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 AV Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 SIMPLINK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 SOUND & LANGUAGE CONTROL APPENDIX Auto Volume Leveler (Auto Volume) . . . . . . . . . . . . . . . . . 73 Clear Voice II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 Preset Sound Settings (Sound Mode) . . . . . . . . . . . . . . . 75 Sound Setting Adjustment - User Mode . . . . . . . . . . . 76 Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 TV Speakers On/Off Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Audio Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 On-Screen Menus Language Selection . . . . . . . . . . . . . 82 Caption Mode - Analog Broadcasting System Captions . . . . . . . 83 - Digital Broadcasting System Captions . . . . . . . . 84 - Caption Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107 External Control Through RS-232C . . . . . . . . . . . . . . . .109 TIME SETTING Clock Setting - Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 - Manual Clock Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Auto On/Off Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 PARENTAL CONTROL / RATINGS Set Password & Lock System . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 Channel Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Movie & TV Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Downloadable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 External Input Blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 FEATURE OF THIS TV ■ This feature is not available for all models. is a trademark of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc. High-definition television. High-resolution digital television broadcast and playback system composed of roughly a million or more pixels, 16:9 aspect-ratio screens, and AC3 digital audio. A subset of digital television, HDTV formats include 1080i and 720p resolutions. Manufactured under license from Dolby Laboratories. “Dolby “and the double-D symbol are trademarks of Dolby Laboratories. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC." IMPORTANT INFORMATION TO PREVENT “IMAGE BURN / BURN-IN” ON YOUR TV SCREEN ■ ■ ■ When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed on the TV for an extended period, it can become permanently imprinted on the screen. This phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the manufacturer’s warranty. In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged period (2 or more hours for LCD, 1 or more hours for Plasma). Image burn can also occur on the letterboxed areas of your TV if you use the 4:3 aspect ratio setting for an extended period. PREPARATION ACCESSORIES EN ER GY AV SAVIN MO INPU IN RET UR TE FLAS FA RA TIO FO EN HB EN ER GY AV SAVIN MO DE INPU CH TE Q.M EN MA RK MU TV LIS VO OFF ME NU ON/ DE VO EX IT IN EN UR TE FLAS FA RA TIO CH TE FO Q.M RET MA RK MU ME NU FR EE ZE EN TV LIS or HB PREPARATION Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the dealer where you purchased the TV. The accessories included may differ from the images below. 1.5V 1.5V EX IT FR EE ZE Owner’s Manual Remote Control, Batteries CD Manual (For 50/60PK550) Power Cord (For 50/60PK550) x4 x2 x3 Cable Holder Protection Cover (Refer to P.14) Bolts for stand assembly (Refer to P.13) Option Extras * Wipe spots on the exterior only with the polishing cloth. * Do not wipe roughly when removing Polishing Cloth stain. Excessive pressure may cause (Not included with all models) scratch or discoloration. D-sub 15 pin Cable When using the VGA (D-sub 15 pin cable) PC connection, the user must use shielded signal interface cables with ferrite cores to maintain standards compliance. Use of ferrite core (Not included with all models) Ferrite Core Ferrite core can be used to reduce the electromagnetic wave when connecting the power cord. The closer the location of the ferrite core to the power plug, the better it is. Install the power plug closely. PREPARATION FRONT PANEL INFORMATION ■ Image shown may differ from your TV. 50/60PK550 PREPARATION Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. ENTER CH VOL ENTER POWER Button INPUT Button MENU Button ENTER Button VOL CH VOLUME Buttons CHANNEL Buttons ENTER 50/60PK250 Remote Control Sensor Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. ENTER VOL CH ENTER POWER Button 10 INPUT Button MENU Button ENTER Button VOL CH VOLUME Buttons CHANNEL Buttons ENTER 42/50PJ350 Remote Control Sensor PREPARATION Power/Standby Indicator Illuminates red in standby mode. Illuminates blue when the TV is switched on. ENTER VOL CH POWER POWER Button OK INPUT Button MENU Button OK Button VOL VOL VOLUME Buttons CH CH CHANNEL Buttons ENTER Do not step on the glass stand or subject it to any impact.It may break, causing possible injury from fragments of glass, or the TV may fall. Do not drag the TV. The floor or the product may be damaged. 11 PREPARATION BACK PANEL INFORMATION Except 50/60PK250 USB IN PREPARATION 10 HDMI IN 3 Image shown may differ from your TV. VIDEO L/MONO AUDIO R ■ AV IN 2 VIDEO RGB IN (PC) HDMI/DVI IN RS-232C IN AV IN 1 REMOTE CONTROL IN VIDEO HDMI IN Digital Connection. Supports HD video and Digital audio. Doesn’t support 480i. Accepts DVI video using an adapter or HDMI to DVI cable (not included) OPTICAL DIGITAL AUDIO OUT Optical digital audio output for use with amps and home theater systems. Note: In standby mode, this port doesn’t work. 12 AUDIO COMPONENT IN REMOTE CONTROL IN PORT For a wired remote control. COMPONENT IN Analog Connection. Supports HD. Uses a red, green, and blue cable for video & red and white for audio. AV (Audio/Video) IN Analog composite connection. Supports standard definition video only (480i). ANTENNA IN Connect over-the air signals to this jack. Connect cable signals to this jack. USB IN Used for viewing photos and listening to MP3. 10 Power Cord Socket For operation with AC power. Caution: Never attempt to operate the TV on DC power. RS-232C IN (CONTROL & SERVICE) PORT Used by third party devices. AUDIO IN (RGB) 1/8” headphone jack for analog PC audio input. RGB IN (PC) Analog PC Connection. Uses a D-sub 15 pin cable (VGA cable). ANTENNA /CABLE IN Except 50/60PK250 /MONO AUDIO (CONTROL & SERVICE) VARIABLE AUDIO OUT OPTICAL AUDIO IN DIGITAL AUDIO OUT (RGB) STAND INSTRUCTION ■ Image shown may differ from your TV. 50/60PK550 Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Assemble the parts of the Stand Body with the Stand Base of the TV. PREPARATION Installation x3 Stand Body Stand Base Fix the 4 bolts securely using the holes in the back of the TV. Fix the 4 bolts securely using the holes in the back of the TV. x4 13 PREPARATION Detachment 50/60PK550 PREPARATION Carefully place the TV screen side down on a cushioned surface to protect the screen from damage. Loose the bolts from TV. Detach the stand from TV. Protection Cover After removing the stand, install the included p r o t e c t i o n c o v e r over the hole for the stand. Press the P R O T E C T I O N C O V E R into the TV until you hear it click. 14 CABLE MANAGEMENT ■ Image shown may differ from your TV. After connecting the cables as necessary, install CABLE HOLDER as shown and bundle the cables. To connect additional equipment, see EXTERNAL EQUIPMENT SETUP section. PREPARATION CABLE HOLDER 15 PREPARATION DESKTOP PEDESTAL INSTALLATION ■ Image shown may differ from your TV. For proper ventilation, allow a clearance of 4 inches on all four sides from the wall. PREPARATION 4 inches 4 inches 4 inches 4 inches CAUTION Ensure adequate ventilation by following the clearance recommendations. Do not mount near or above any type of heat source. SWIVEL STAND (This feature is not available for all models.) After installing the TV, you can adjust the TV manually to the left or right direction by 20 degrees to suit your viewing position. 16 VESA WALL MOUNTING VESA (A * B) Model 50/60PK550, 42/50PJ350, 50/60PK250 400 * 400 Standard Screw Quantity M6 Wall Mounting bracket (sold separately) PREPARATION Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest installer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. We recommend that you use an LG brand wall mount when mounting the TV to a wall. LG recommends that wall mounting be performed by a qualified professional installer. AW-50PG60MS ! NOTE Screw length needed depends on the wall mount used. For further information, refer to the instructions included with the mount. Standard dimensions for wall mount kits are shown in the table. When purchasing our wall mount kit, a detailed installation manual and all parts necessary for assembly are provided. Do not use screws longer then the standard dimension, as they may cause damage to the inside to the TV. For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on their specifications. Do not use screws that do not comply with the VESA standard screw specifications. Do not use fasten the screws too strongly, this may damage the TV or cause the TV to a fall, leading to personal injury. LG is not liable for these kinds of accidents. LG is not liable for TV damage or personal injury when a non-VESA or non specified wall mount is used or the consumer fails to follow the TV installation instructions. CAUTION Do not install your wall mount kit while your TV is turned on. It may result in personal injury due to electric shock. 17 PREPARATION SECURING THE TV TO THE WALL TO PREVENT FALLING WHEN THE TV IS USED ON A STAND ■ PREPARATION ■ ■ You should purchase necessary components to prevent the TV from tipping over (when not using a wall mount). Image shown may differ from your TV. We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards. Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction, potentially causing injury or damaging the product. Caution: Please make sure that children don’t climb on or hang from the TV. Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture. * If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the bolts. * Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes. Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket that is mounted on the wall to the holes in the product. Ensure the eye-bolts or brackets are tightened securely. ■ Use a sturdy rope (sold separately) to tie the product. It is safer to tie the rope so it becomes horizontal between the wall and the product. ! NOTE 18 Use a platform or cabinet strong enough and large enough to support the size and weight of the TV. To use the TV safely, make sure that the height of the bracket on the wall and the one on the TV are the same. ■ To prevent damage do not connect to the power outlet until all connections are made between the devices. ANTENNA OR CABLE CONNECTION PREPARATION 1. Antenna (Analog or Digital) Wall Antenna Socket or Outdoor Antenna without a Cable Box Connection. For optimum picture quality, adjust antenna direction if needed. Outdoor Antenna (VHF, UHF) Multi-family Dwellings/Apartments (Connect to wall antenna socket) ANTENNA /CABLE IN RF Coaxial Wire (75 ohm) Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) VARIABLE AUDIO OUT Wall Antenna Socket Copper Wire Be careful not to bend the copper wire when connecting the antenna. 2. Cable Cable TV Wall Jack RF Coaxial Wire (75 ohm) ANTENNA /CABLE IN To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly. If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter. ■ If the antenna is not installed properly, contact your dealer for assistance. ■ ■ 19 EXTERNAL EQUIPMENT SETUP ■ To prevent the equipment damage, never plug in any power cords until you have finished connecting all equipment. ■ Image shown may differ from your TV. HD RECEIVER SETUP This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. O IN DVI) 1. How to connect Connect the video outputs (Y, PB, PR) of the digital settop box to the C O M P O N E N T I N V I D E O 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). REMOTE CONTROL IN ■ ■ /MONO AUDIO VIDEO AUDIO COMPONENT IN Connect the audio output of the digital set-top box to the C O M P O N E N T I N A U D I O 1 jacks on the TV. PB ANTE CA Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box. operation) Select the C o m p o n e n t 1 input source on the TV using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2 input, select the C o m p o n e n t 2 input source on the TV. 2. How to use ■ AV IN 1 VIDEO RGB IN (PC) EXTERNAL EQUIPMENT SETUP Component Connection PR Supported Resolutions Y, CB/PB, CR/PR Signal 20 Component HDMI 480i Yes No 480p Yes Yes 720p Yes Yes 1080i Yes Yes 1080p Yes Yes Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480i 15.73 15.73 59.94 60.00 720x480p 31.47 31.50 59.94 60.00 1280x720p 44.96 45.00 59.94 60.00 1920x1080i 33.72 33.75 59.94 60.00 1920x1080p 27.00 33.75 67.43 67.50 24.00 30.00 59.94 60.00 1. How to connect OPTICAL AUDIO DIGITAL AUDIO OUT (RGB/DVI) Connect the digital set-top box to H D M I / D V I I N 1, 2 or 3 (Except 50/60PK250) jack on the TV. HDMI/DVI IN 2. How to use RGB(PC) No separate audio connection is necessary. HDMI supports both audio and video. RS-232C IN (CONTROL & SERVICE) EXTERNAL EQUIPMENT SETUP HDMI Connection Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ■ Select the H D M I 1, 2 or 3 (Except 50/60PK250) input source on the TV using the INPUT button on the remote control. ■ ! NOTE Check HDMI cable over version 1.3. If the HDMI cables don’t support HDMI version 1.3, it can cause flickers or no screen display. In this case use the latest cables that support HDMI version 1.3. HDMI-DTV OUTPUT HDMI-DTV Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x480p 31.469 31.50 59.94 60.00 1280x720p 44.96 45.00 59.94 60.00 1920x1080i 33.72 33.75 59.94 60.00 1920x1080p 27.00 33.75 67.43 67.50 24.00 30.00 59.94 60.00 21 EXTERNAL EQUIPMENT SETUP DVI to HDMI Connection 1. How to connect Connect the audio output of the digital set-top box to the A U D I O I N ( R G B / D V I ) jack on the TV. 2. How to use Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) ■ Select the H D M I 1, 2 or 3 (Except 50/60PK250) input source on the TV using the I N P U T button on the remote control. HDMI/DVI IN ■ ! NOTE A DVI to HDMI cable or adapter is required for this connection. DVI doesn't support audio, so a separate audio connection is necessary. DVI-DTV OUTPUT 22 RE CON RGB IN (PC) OPTICAL AUDIO IN DIGITAL AUDIO OUT (RGB/DVI) RS-232C IN Connect the DVI output of the digital set-top box to the H D M I / D V I I N 1, 2 or 3 (Except 50/60PK250) jack on the TV. (CONTROL & SERVICE) EXTERNAL EQUIPMENT SETUP DVD SETUP Component Connection 1. How to connect Connect the audio outputs of the DVD to the C O M P O N E N T I N A U D I O 1 jacks on the TV. AV IN 1 VIDEO RGB IN (PC) REMOTE CONTROL IN /MONO AUDIO VIDEO AUDIO COMPONENT IN 2. How to use ■ ■ ■ ■ Turn on the DVD player, insert a DVD. Select the C o m p o n e n t 1 input source on the TV using the I N P U T button on the remote control. If connected to C O M P O N E N T I N 2 input, select the C o m p o n e n t 2 input source on the TV. Refer to the DVD player's manual for operating instructions. PB PR EXTERNAL EQUIPMENT SETUP Connect the video outputs (Y, PB, PR) of the DVD to the C O M P O N E N T I N V I D E O 1 jacks on the TV. Match the jack colors (Y = green, PB = blue, and PR = red). DIO IN B/DVI) Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV Video output ports on DVD player PB PR PB PR B-Y R-Y Cb Cr Pb Pr 23 EXTERNAL EQUIPMENT SETUP HDMI Connection 1. How to connect No separate audio connection is necessary. HDMI supports both audio and video. 2. How to use ■ Select the HDMI1, 2 or 3 (Except 50/60PK250) input source on the TV using the I N P U T button on the remote control. Refer to the DVD player's manual for operating instructions. HDMI-DVD OUTPUT RS 232C IN HDMI/DVI IN ■ 24 Connect the HDMI output of the DVD to the H D M I / D V I I N 1, 2 or 3 (Except 50/60PK250) jack on the TV. (CONTROL & SERVICE) EXTERNAL EQUIPMENT SETUP VCR SETUP Antenna Connection 1. How to connect ANTENNA IN EXTERNAL EQUIPMENT SETUP Connect the RF antenna out socket of the VCR to the A N T E N N A / C A B L E I N socket on the TV. Connect the antenna cable to the RF antenna in socket of the VCR. ANT OUT S-VIDEO ANT IN OUTPUT SWITCH VIDEO Wall Jack 2. How to use ■ ■ Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Antenna Composite (RCA) Connection ANT IN S-VIDEO ANT OUT OUTPUT SWITCH VIDEO 1. How to connect V I D E O jacks between TV and Connect the A U D I O/V VCR. Match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red) 2. How to use ■ Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) Select the A V 1 input source on the TV using the I N P U T button on the remote control. ■ If connected to A V I N 2, select A V 2 input source on the TV. ■ UDIO B/DVI) VIDEO ! NOTE If you have a mono VCR, connect the audio cable from the VCR to the A U D I O L / M O N O jack of the TV. /MONO AUDIO RG AV IN 1 REMOTE CONTROL IN 25 EXTERNAL EQUIPMENT SETUP OTHER A/V SOURCE SETUP Camcorder 1. How to connect ■ ■ ■ Select the A V 2 input source on the TV using the I N P U T button on the remote control. If connected to A V I N 1 input, select the A V 1 input source on the TV. Operate the corresponding external equipment. USB IN HDMI IN 3 EXTERNAL EQUIPMENT SETUP 2. How to use VIDEO VIDEO L/MONO AUDIO R Video Game Set V I D E O jacks Connect the A U D I O/V between TV and external equipment. Match the jack colors. (Video = yellow, Audio Left = white, and Audio Right = red) AV IN 2 Connect the USB device to the U S B I N jack on the side of TV. 2. How to use ■ After connecting the U S B I N jack, you use the USB function. (G p .50) HDMI / DVI IN 3 i.e) VIDEO L/MONO AUDIO R 1. How to connect USB IN USB CONNECTION AV IN 2 26 AUDIO OUT CONNECTION Send the TV’s audio to external audio equipment via the Audio Output port. 1. How to connect OPTICAL DIGITAL AUDIO OUT AUDIO (RGB/DVI) Connect the other end of the optical cable to the digital audio input on the audio equipment. HDMII/DVI IN RGB(PC) ! NOTE RS-232C IN Set the “TV Speaker option - Off” in the AUDIO menu. (G p.78). See the external audio equipment instruction manual for operation. (CONTROL & SERVICE) EXTERNAL EQUIPMENT SETUP Connect one end of the optical cable to the TV’s O P T I C A L port of D I G ITAL AUDIO OUT. When connecting with external audio equipment, such as amplifiers or speakers, you can turn the TV speakers off in the menu. (G p.78) CAUTION Do not look into the optical output port. Looking at the laser beam may damage your vision. Audio with ACP (Audio Copy Protection) function may block digital audio output. 27 EXTERNAL EQUIPMENT SETUP PC SETUP (FOR ???) This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. OPTICAL DIGITAL AUDIO OUT VGA (D-Sub 15 pin) Connection REMOTE CONTROL IN AUDIO IN (RGB/DVI) HDMII IN Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. RGB IN (PC) Connect the VGA output of the PC to the R G B I N ( P C) jack on the TV. RS-232C IN RS-232C IN (CONTROL & SERVICE) EXTERNAL EQUIPMENT SETUP 1. How to connect 2. How to use ■ ■ Turn on the PC and the TV. Select the R G B - P C input source on the TV using the I N P U T button on the remote control. RGB OUTPUT AUDIO OPTICAL AUDIO IN DIGITAL (RGB/DVI) AUDIO OUT DVI to HDMI Connection 1. How to connect Connect the PC audio output to the A U D I O I N ( R G B / D V I ) jack on the TV. HDMI/DVI IN RGB IN (PC) RS-232C IN Connect the DVI output of the PC to the H D M I / D V I I N 1, 2 or 3 (Except 50/60PK250) jack on the TV. (CONTROL & SERVICE) 2. How to use Turn on the PC and the TV. ■ Select the H D M I 1, 2 or 3 (Except 50/60PK250) input source on the TV using the I N P U T button on the remote control. ■ DVI-PC OUTPUT 28 AUDIO ! NOTES Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use. In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear. Avoid keeping a fixed image on the screen for a long period of time. The fixed image could become permanently imprinted on the screen. The synchronization input form for Horizontal and Vertical frequencies is separate. Depending on the graphics card, some resolution settings may not allow the image to be positioned on the screen properly. EXTERNAL EQUIPMENT SETUP Supported Display Specifications (RGB-PC, HDMI-PC) Resolution Horizontal Frequency(KHz) Vertical Frequency(Hz) 720x400 31.468 70.08 640x480 31.469 59.94 800x600 37.879 60.31 1024x768 48.363 60.00 1280x768 47.78 59.87 1360x768 47.72 59.80 1920x1080 66.647 59.988 29 EXTERNAL EQUIPMENT SETUP Screen Setup for PC mode Selecting Resolution PICTURE Move Screen Enter • Contrast • Brightness • H Sharpness • V Sharpness • Color • Tint 90 50 60 60 60 Resolution Auto config. MENU Prev. 1024 x 768 1280 x 768 1360 x 768 Position Size • Expert Control • Reset Phase Screen (RGB-PC) Reset MENU Select P I C T U R E. ENTER Select S c r e e n ( R G B - P C ). ENTER 30 Move EXTERNAL EQUIPMENT SETUP You can choose the resolution in RGB-PC mode. The P o s i t i o n, P h a s e, and S i z e can also be adjusted. Select R e s o l u t i o n. ENTER ENTER Select the desired resolution. Screen Auto Configure Move MENU Prev. Resolution Auto config. G To Set Position Size Yes No Phase Reset MENU Select P I C T U R E. ENTER Select S c r e e n ( R G B - P C ). ENTER Select Y e s. ENTER Start Auto Configuration. ENTER EXTERNAL EQUIPMENT SETUP Automatically adjusts picture position and minimizes image instability. After adjustment, if the image is still not correct, try using the manual settings or a different resolution or refresh rate on the PC. Select A u t o c o n f i g .. • If the position of the image is still not correct, try Auto adjustment again. • If picture needs to be adjusted again after Auto adjustment in RGB-PC, you can adjust the P o s i t i o n, S i z e or P h a s e. 31 EXTERNAL EQUIPMENT SETUP Adjustment for screen Position, Size, and Phase If the picture is not clear after auto adjustment and especially if characters are still trembling, adjust the picture phase manually. This feature operates only in RGB-PC mode. EXTERNAL EQUIPMENT SETUP PICTURE Move Screen Enter Move MENU Prev. • Contrast • Brightness • H Sharpness • V Sharpness • Color • Tint 90 50 60 60 60 Resolution Auto config. Position • Expert Control • Reset Screen (RGB-PC) Size Phase Reset MENU ENTER ENTER Select P I C T U R E. ■ Select S c r e e n ( R G B - P C ). ■ Select P o s i t i o n, S i z e, or P h a s e. ■ ENTER ENTER 32 Make appropriate adjustments. P o s i t i o n: This function is to adjust picture to left/right and up/down as you prefer. S i z e: This function is to minimize any vertical bars or stripes visible on the screen background. And the horizontal screen size will also change. P h a s e : This function allows you to remove any horizontal noise and clear or sharpen the image of characters. Screen Reset (Reset to original factory values) Returns P o s i t i o n, S i z e, and P h a s e to the default factory settings. This feature operates only in RGB-PC mode. Move Screen Enter Move MENU Prev. • Contrast • Brightness • H Sharpness • V Sharpness • Color • Tint 90 50 60 60 60 Resolution Auto config. Position • Expert Control • Reset Screen (RGB-PC) Initialize Settings. Yes Size Phase Reset No EXTERNAL EQUIPMENT SETUP PICTURE MENU Select P I C T U R E. ENTER Select S c r e e n ( R G B - P C ). ENTER Select R e s e t. ENTER Select Y e s. ENTER 33 WATCHING TV / CHANNEL CONTROL REMOTE CONTROL FUNCTIONS When using the remote control, aim it at the remote control sensor on the TV. 50PK250, 42PJ350 ENERGY POWER Turns the TV on from standby or off to standby. WATCHING TV / CHANNEL CONTROL ON/OFF Illuminates the remote control buttons. AV MODE INPUT TV SAVING 50/60PK550 ENERGY SAVING Adjusts the Energy Saving. ON/OFF AV MODE Toggles through preset Video and Audio modes. G p.47 ENERGY INPUT Rotates through inputs. Also switches the TV on from standby. G p.45 TV Select the remote operating mode: TV NUMBER button — (DASH) Used to enter a program number for multiple program channels such as 2-1, 2-2, etc. LIST Displays the channel list. AV MODE TV SAVING LIST FLASHBK MARK FLASHBK Tunes to the last channel viewed. FAV VOL RATIO CH MUTE Coloured Programme edit. buttons MENU SIMPLINK Control buttons INPUT INFO Q.MENU (Fast Forward), G (Playback), l l (Pause) Controls the SIMPLINK compatible devices. FF (Rewind), GG ENTER FREEZE Freezes the current frame. RETURN EXIT FREEZE 34 THUMBSTICK (Up/Down/Left Navigates the on-screen menus and adjusts the system settings to your preference. Right/ENTER) INFO Displays channel information at the top of the screen. Q.MENU Opens the list of Quick Menu options. RETURN Allows the user to move return one step in an interactive application or other user interaction function. SIMPLINK Displays channel information at the top of the screen. EXIT VOLUME UP /DOWN Adjusts the volume. FAV Scroll through the programmed Favorite channels. G p.43 WATCHING TV / CHANNEL CONTROL MENU Displays the main menu or clears all on-screen displays and returns to TV viewing. RATIO Changes the aspect ratio. MUTE Switches the sound on or off. G p.34 CHANNEL UP/DOWN Changes the channel. PAGE UP/DOWN Moves from one full set of screen information to the next one. Installing Batteries ■ Open the battery compartment cover on the back side and install the batteries matching correct polarity. ■ Install two 1.5V AAA batteries. Don’t mix old or used batteries with new ones. ■ Close cover. 35 WATCHING TV / CHANNEL CONTROL TURNING ON TV First, connect power cord correctly. At this moment, TV is in standby mode. ■ In standby mode to turn TV on, INPUT, CH (D or E ) button on the TV or press the POWER, INPUT, CH( ), Number (0~9 9) button on the remote control. WATCHING TV / CHANNEL CONTROL Select the viewing source by using the I N P U T button on the remote control. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. ! NOTE If you intend to be away on vacation, disconnect the power plug from the wall power outlet. CHANNEL SELECTION Press the C H ( or ) or NUMBER buttons to select a channel number. VOLUME ADJUSTMENT Adjust the volume to suit your personal preference. 36 Press the V O L ( + or - ) button to adjust the volume. If you want to switch the sound off, press the M U T E button. You can cancel the Mute function by pressing the MUTE or V O L ( + or - ) button. or INITIAL SETTING This Function guides the user to easily set the essential items for viewing the TV for the first time when purchasing the TV. It will be displayed on the screen when turning the TV on for the first time. It can also be activated from the user menus. H o m e U s e”. We recommend setting the TV to “H H o m e U s e” mode for the best picture Default selection is “H in your home environment. ■ “S S t o r e D e m o” Mode is only intended for use in retail environments. Customers can adjust the “P Picture menu - P i c t u r e m o d e” manually while inspecting the TV, but the TV will automatically return to preset instore mode after 5 minutes. ■ You can also adjust I n i t i a l S e t t i n g in the O P T I O N menu. H o m e U s e”. Factory defaults are set when you choose “H ■ If you do not complete the I n i t i a l s e t t i n g, it will appear whenever the TV is switched on until the I n i t i a l s e t t i n g procedure is completed. ■ Language English ENTER Select menu Language. ENTER Select H o m e U s e mode. Español Français Next WATCHING TV / CHANNEL CONTROL Step1. Language Selecting Step2. Mode setting Mode Setting Selecting the environment. Choose the setting mode you want. Store Demo Home Use Select [Home Use] to use this TV at home. Previous Next 37 WATCHING TV / CHANNEL CONTROL Step3. Time setting Time Setting Current Time Setting Year WATCHING TV / CHANNEL CONTROL Month Auto 2007 15 Hour 5 PM Time Zone Daylight Saving Previous Select A u t o or M a n u a l. 11 Date Minute ENTER 52 Select desired time option. Eastern Off Next Step4. Auto Tuning ENTER Auto Tuning Check your antenna connection. The previous channel information will be updated during Auto Tuning. Previous 38 Next Start A u t o T u n i n g. ON-SCREEN MENUS SELECTION Your TV's OSD (On Screen Display) may differ slightly from that shown in this manual. CHANNEL Move PICTURE Enter Move Auto Tuning Manual Tuning Channel Edit AUDIO Enter Move Auto Volume : Off Clear Voice II : On +3 Balance Sound Mode 90 50 60 60 Enter : Standard • SRS TruSurround XT:Off • Treble 50 • Bass 50 • Reset TV Speaker : On OPTION Move TIME Enter Language Move Enter Move Enter Clock Input Label SIMPLINK : On Key Lock : Off Caption : Off ISM Method : Normal Set ID :1 Initial Setting CHANNEL PICTURE AUDIO TIME Off Time : Off On Time : Off Sleep Timer : Off : Store Demo OPTION LOCK INPUT USB LOCK Move INPUT Enter Move Enter USB TV Photo List Set Password Set Password AV1 Music List Block Channel Block Channel AV2 Movie Rating TV Rating-English Component1 TV Rating-Children TV Rating-French TV Rating-General Downloadable Rating Downloadable Rating Input Block Lock System : Off Lock System : Off Input Block WATCHING TV / CHANNEL CONTROL Aspect Ratio : 16:9 Picture Wizard Energy Saving : Off Picture Mode : Standard • Contrast • Brightness • Sharpness • Color • Tint Component2 RGB-PC HDMI1 HDMI2 HDMI3 For USA For Canada MENU Display each menu. ENTER Select a menu item. ! NOTE P i c t u r e W i z a r d: For 50/60PK550, 42/50PJ350. I N P U T , U S B Menu: Except 50/60PK250 ENTER Accept the current selection. MENU Return to TV viewing. 39 WATCHING TV / CHANNEL CONTROL QUICK MENU Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Q.Menu (Quick Menu) is a menu of features which users might use frequently. Q.Menu Aspect Ratio 16:9 WATCHING TV / CHANNEL CONTROL Picture Mode Vivid Sound Mode Standard Off Caption English Multi Audio CH Sleep Timer Off Del/Add/Fav Add Eject USB Eject Close CH Except 50/60PK250 Q.MENU Display each menu. Make appropriate adjustments. Q.MENU 40 Return to TV viewing. A s p e c t R a t i o: Selects your desired picture format. P i c t u r e M o d e: Selects the factory preset picture depend on the viewing environment. S o u n d M o d e: Selects the factory preset sound for type of program. M u l t i A u d i o: Changes the audio language (Digital signal). S A P: Selects MTS sound (Analog signal). S l e e p T i m e r: Select the amount of time before your TV turns off automatically. D e l / A d d / F a v: Select channel you want to add/delete or add the channel to the Favorite List. C a p t i o n: Select on or off. U S B D e v i c e: Select “Eject” in order to eject a USB device. CHANNEL SETUP Auto Scan (Auto Tuning) Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. Run this function if you change your residence or move the TV. Also, make sure to run this function with the antenna connected during TV broadcasting hours. Auto Tuning memorizes only the channels available at the time. Move Enter CHANNEL Auto Tuning Manual Tuning Manual Tuning Channel Edit Channel Edit Move Enter Press ‘Yes’ button to begin auto tuning. Processing Auto Tuning... 23% DTV Channel 8 DTV : 0 Found Channel(s) ATV : 0 Found Channel(s) Yes Next(TV) No Close MENU Select C H A N N E L. WATCHING TV / CHANNEL CONTROL CHANNEL Auto Tuning ENTER Select A u t o T u n i n g. ■ ENTER Select Y e s. ■ ENTER Run A u t o T u n i n g. EXIT Return to the previous menu. MENU Return to TV viewing. ■ The TV will ask for a password if parental control has been activated (LOCK Menu). Use the password you set up in the LOCK Menu to allow a channel search. When setting the Auto tuning or Manual tuning, the number of maximum channel you can store is 900. It is subject to change depending on the broadcasting signal environment. Memorizes all the available channels in the order of DTV, TV, CADTV and CATV. 41 WATCHING TV / CHANNEL CONTROL Add/Delete Channel (Manual Tuning) If you select DTV or CADTV input signal, you can view the on-screen signal strength monitor to see the quality of the signal being received. CHANNEL Move Enter WATCHING TV / CHANNEL CONTROL Auto Tuning Manual Tuning Manual Tuning Channel Edit Channel Edit Move Enter DTV Select channel type and RF-channel number. Channel DTV 2-1 Bad Normal Good Delete Close Select C H A N N E L. MENU Select M a n u a l T u n i n g. ENTER ■ ENTER Select D T V, T V, C A D T V, or C A T V. Select channel you want to add or delete. ENTER Select A d d or D e l e t e. 42 CHANNEL Auto Tuning EXIT Return to the previous menu. MENU Return to TV viewing. ■ The TV will ask for a password if parental control has been activated (LOCK Menu). Use the password you set up in the LOCK Menu to allow a channel search. When setting the Auto tuning or Manual tuning, the number of maximum channel you can store is 900. It is subject to change depending on the broadcasting signal environment. Channel Editing When a channel number is deleted, it means that you will be unable to select it using CH , button during TV viewing. If you wish to select the deleted channel, directly enter the channel number with the NUMBER buttons or select it in the Channel Edit menu. Move Enter Manual Tuning Channel Edit Ch.Change Move CH Move Page Previous Add/Delete WATCHING TV / CHANNEL CONTROL CHANNEL Auto Tuning MENU ENTER Select C H A N N E L. ■ Select C h a n n e l E d i t. ■ Keep pressing the button and use the or buttons to move between DTV, TV, CADTV and CATV. If the channel list is too long, use the C H or button to move between pages. ENTER Select a channel. Add or delete the channel. EXIT Return to the previous menu. MENU Return to TV viewing. 43 WATCHING TV / CHANNEL CONTROL CHANNEL LIST You can check channels which are stored in the memory by displaying the channel list. Channel List This padlock is displayed when the channel is locked with parental control. DTV 83-0 DTV 15-1 DTV 18-2 WATCHING TV / CHANNEL CONTROL Exit Displaying Channel List Display the C h a n n e l L i s t. LIST Selecting a channel in the channel list Select a channel. ENTER Switch to the chosen channel number. Paging through a channel list CH 44 EXIT Turn the pages. Return to TV viewing. FAVORITE CHANNEL SETUP Your TV's OSD (On Screen Display) may differ slightly from what is shown in this manual. Favorite Channels are a convenient feature that lets you quickly select channels of your choice without waiting for the TV to select through all the in-between channels. To tune to a favorite channel, press the F A V (Favorite) button repeatedly. Q.Menu CH 16:9 Picture Mode Vivid Sound Mode Standard Select your desired channel. Q.MENU Select D e l / A d d / F a v. Off Caption CH or Multi Audio English Sleep Timer Off Del/Add/Fav Favorite Eject Eject USB Select F a v o r i t e. Q.MENU Return to TV viewing. Close FAVORITE CHANNEL LIST Displaying the favorite channel list 1 MARK Favorite List Display the Favorite channel list. FAV DTV 83-0 DTV 15-1 DTV 18-2 WATCHING TV / CHANNEL CONTROL Aspect Ratio Selecting a channel in the favorite channel list Select a channel. ENTER Exit Switch to the chosen channel number. Paging through a favorite channel list CH EXIT Turn the pages. Return to TV viewing. 45 WATCHING TV / CHANNEL CONTROL BRIEF INFORMATION Brief Info shows the present screen information. or INFO ENTER Show the Brief Info on the screen. WATCHING TV / CHANNEL CONTROL EXIT Return to TV viewing No Program Information. Wed, Aug 21, 2009 Multilingual CC 4:3 16:9 480i 480p 720p 1080i 1080p CC 10:40 AM 10:10 AM Caption DOLBY DIGITAL 11:40 AM 1080i CNN MPAA PG Multilingual : The program contains two or more audio services. Use the Q . M E N U menu to select wanted Audio. Program title Day, Month, Year Caption : The program contains one or more caption services. Use the Q . M E N U menu to select wanted Closed caption. Program start time Program progress bar The original aspect ratio of the video is 4:3 The original aspect ratio of the video is 16:9 (wide) Program finish time Present time Banner information The video resolution is 720x480i The video resolution is 720x480p The video resolution is 1280x720p The video resolution is 1920x1080i The video resolution is 1920x1080p V - C h i p: The program contains V-Chip information. Refer to the LOCK menu: A (Age), D (Dialogue), L (Language), S (Sex), V (Violence), FV (Fantasy Violence) 46 INPUT LIST Only these input signals which are connected to a TV can be activated and selected. TV AV2 Component1 Component2 INPUT ENTER Select the desired input source. TV AV1 HDMI3 HDMI2 AV2 Component1 HDMI1 Component2 RGB-PC or HDMI2 ie) Disconnected inputs are inactive (grayed out) TV AV1 AV2 Component1 Component2 Input Label Exit WATCHING TV / CHANNEL CONTROL AV1 Select a desired input source (except T V). Then, you can select your desired I n p u t L a b e l with using Blue button. G p . 4 8 ie) In case of changing the input label with using Blue button ■ ■ When new external device is connected, this popup menu is displayed automatically. If selecting Y e s, you can select input source that you want to appreciate. S I M P L I N K - O n”, popup menu for HDMI input will not be displayed. But, when selecting “S New external device is connected. Do you want to enjoy this? Select input source that you want to appreciate. AV1 Yes AV2 No Component1 ■ ■ ■ T V: Select it to watch over-the-air, cable and digital cable broadcasts. A V: Select them to watch a VCR or other external equipment. C o m p o n e n t: Select them to watch DVD or a Digital set-top box. ■ ■ R G B - P C: Select it to view PC input. H D M I: Select them to watch high definition devices. 47 WATCHING TV / CHANNEL CONTROL INPUT LABEL This indicates which device is connected to which input port. OPTION Move Enter OPTION Move Enter Menu Language(Language): English Menu Language(Language): English Audio Language Audio Language : English WATCHING TV / CHANNEL CONTROL : On SIMPLINK Key Lock : Off Key Lock Caption : Off Caption Demo Mode : Off Demo Mode ISM Method : Normal ISM Method :1 Set ID SIMPLINK Set ID : English AV1 Input Label Input Label : On AV2 : Off Component1 : Off Component2 : Off RGB-PC : Normal Except 50/60PK250 :1 HDMI1 HDMI2 HDMI3 Except 50/60PK250 Close With using OPTION menu With using INPUT button MENU Select O P T I O N. ENTER Select I n p u t L a b e l. ENTER Select the source. INPUT Select the source(except T V). Select the label. EXIT Return to the previous menu. MENU Return to TV viewing. Select the label. 48 EXIT Return to the previous menu. MENU Return to TV viewing. AV MODE AV Mode toggles through preset Video and Audio settings. Cinema Game Sport Press the A V M O D E button repeatedly to select the desired source. ENTER ■ ■ ■ ■ ■ ■ WATCHING TV / CHANNEL CONTROL 1AV MODE Off C i n e m a” in AV mode, If you select “C C i n e m a will be selected both for “PICTURE menu - Picture Mode” and “AUDIO menu - Sound Mode” respectively. O f f” in AV mode, the If you select “O P i c t u r e M o d e” and “S S o u n d M o d e” “P return to previous selected value. O f f: Disables the AV MODE. C i n e m a: Optimizes video and audio for watching movies. S p o r t: Optimizes video and audio for watching sports events. G a m e: Optimizes video and audio for playing games. 49 WATCHING TV / CHANNEL CONTROL Simplink allows you to control and play other AV devices connected with HDMI cable without additional cables and settings. This TV may work with devices with HDMI-CEC support, but only devices with the logo are fully supported. SIMPLINK can be turned on and off in the user menus. OPTION Move Enter OPTION Move Enter WATCHING TV / CHANNEL CONTROL Menu Language : English Menu Language : English Audio Language : English Audio Language : English Input Label Input Label SIMPLINK : On SIMPLINK : On Off Key Lock : Off Key Lock : Off On Caption : Off Caption : Off Demo Mode : Off Demo Mode : Off ISM Method : Normal ISM Method : Normal Set ID :1 Set ID :1 MENU Select O P T I O N. ENTER Select S I M P L I N K. ENTER Select O n or O f f. EXIT Return to the previous menu. MENU Return to TV viewing. ! NOTE Connect the HDMI/DVI IN or HDMI IN terminal of the TV to the rear terminal (HDMI terminal) of the SIMPLINK device with the HDMI cable. G When you switch the Input source with the INPUT button on the remote control, the SIMPLINK device will stop. G When you select a device with home theater functionality, the sound output automatically switches to the home theater speakers and the TV speakers are turned off. G If a connected SIMPLINK home theater system doesn't play the audio from the TV, connect the DIGITAL AUDIO OUT terminal on the back of the TV to the DIGITAL AUDIO IN terminal on the back of the SIMPLINK device with an OPTICAL cable. 50
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : Yes Page Count : 50 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:86646960-3b28-485f-bcd0-ff21aa4e3222 Modify Date : 2009:10:27 16:13:36+09:00 Create Date : 2009:10:27 16:13:20+09:00 Metadata Date : 2009:10:27 16:13:36+09:00 Document ID : uuid:308e35af-0c18-4b31-8a0d-8e14e71e877e Format : application/pdf Title : SAC33575901-Edit1-en Creator : QuarkXPress3.32: LaserWriter 8 8.7.3 Author : KWM Producer : Acrobat Distiller 6.0 for MacintoshEXIF Metadata provided by EXIF.tools