LG Electronics USA 50PX950UA Plasma monitor User Manual 50PX950 U 1

LG Electronics USA Plasma monitor 50PX950 U 1

UserManual.wiki >

LG Electronics USA >

50PX950UA User Manual >

User manual 1 of 2 HTML Version

1. User manual 1 of 2
2. User manual 2 of 2

User manual 1 of 2

OWNER’S MANUAL

LED LCD TV / PLASMA TV

Please read this manual carefully before operating

your set and retain it for future reference.

P/NO : SAC34134205 (1006-REV03) www.lg.com

The model and serial number of the TV is located

on the back and/or one side of the TV.

Record it below should you ever need service.

MODEL

SERIAL

LED LCD TV MODELS

47LX9500

55LX9500

47LEX8

55LEX8

60LEX9

72LEX9

PLASMA TV MODELS

50PK950

60PK950

50PX950

60PX950

WARNING / CAUTION

The lightning flash with arrowhead

symbol, within an equilateral trian-

gle, is intended to alert the user to

the presence of uninsulated “dan-

gerous voltage” within the product’s enclo-

sure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert

the user to the presence of important oper-

ating and maintenance (servicing) instruc-

tions in the literature accompanying the

appliance.

TO REDUCE THE RISK OF ELECTRIC

SHOCK DO NOT REMOVE COVER (OR

BACK). NO USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED SERVICE

PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND

ELECTRIC SHOCK, DO NOT EXPOSE THIS

PRODUCT TO RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system

installer’s attention to Article 820-40 of the National

Electric Code (U.S.A.). The code provides guide-

lines for proper grounding and, in particular, speci-

fies that the cable ground shall be connected to the

grounding system of the building, as close to the

point of the cable entry as practical.

WARNING / CAUTION

To prevent fire or shock hazards, do not expose

this product to rain or moisture.

FCC Notice

Class B digital device

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable pro-

tection against harmful interference in a residen-

tial installation. This equipment generates, uses

and can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning

the equipment off and on, the user is encour-

aged to try to correct the interference by one or

more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equip-

ment and receiver.

- Connect the equipment to an outlet on a circuit

different from that to which the receiver is con-

nected.

- Consult the dealer or an experienced radio/TV

technician for help.

This device complies with part 15 of the FCC

Rules.

Operation is subject to the following two condi-

tions: (1) This device may not cause (harmful)

interference, and (2) this device must accept

any interference received, including interference

that may cause undesired operation (of the

device).

Any changes or modifications in construction of

this device which are not expressly approved by

the party responsible for compliance could void

the user’s authority to operate the equipment.

CAUTION

Do not attempt to modify this product in any

way without written authorization from LG

Electronics.

Unauthorized modification could void the user’s

authority to operate this product.

SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

1Do not use this apparatus near water.

2Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such as

radiators, heat registers, stoves, or other appa-

ratus (including amplifiers) that produce heat.

Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has

two blades with one wider than the other. A

grounding type plug has two blades and a third

grounding prong, The wide blade or the third

prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an elec-

trician for replacement of the obsolete outlet.

6Protect the power cord from being walked

on or pinched particularly at plugs, conve-

nience receptacles, and the point where

they exit from the apparatus.

7Only use attachments/accessories speci-

fied by the manufacturer.

8Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is

used, use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

9Unplug this apparatus during lighting

storms or when unused for long periods

of time.

Refer all servicing to qualified service per-

sonnel. Servicing is required when the

apparatus has been damaged in any way,

such as power-supply cord or plug is dam-

aged, liquid has been spilled or objects

have fallen into the apparatus, the appara-

tus has been exposed to rain or moisture,

does not operate normally, or has been

dropped.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

Never touch this apparatus or antenna during

a thunder or lighting storm.

When mounting a TV on the wall, make sure

not to install the TV by the hanging power

and signal cables on the back of the TV.

Do not allow an impact shock or any objects

to fall into the product, and do not drop onto

the screen with something.

CAUTION concerning the Power Cord:

It is recommend that appliances be placed

upon a dedicated circuit; that is, a single

outlet circuit which powers only that appli-

ance and has no additional outlets or

branch circuits. Check the specification page

of this owner's manual to be certain.

Do not connect too many appliances to the

same AC power outlet as this could result in

fire or electric shock.

Do not overload wall outlets. Overloaded wall

outlets, loose or damaged wall outlets, exten-

sion cords, frayed power cords, or damaged

or cracked wire insulation are dangerous . Any

of these conditions could result in electric

shock or fire. Periodically examine the cord of

your appliance, and if its appearance indicates

damage or deterioration, unplug it, discon-

tinue use of the appliance, and have the cord

replaced with an exact replacement part by

an authorized servicer. Protect the power cord

from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a

door, or walked upon. Pay particular attention

to plugs, wall outlets, and the point where the

cord exits the appliance.

Do not use a damaged or loose power cord.

Do not pull on the power cord to unplug the

TV. Grasp the plug when unplugging the

power cord.

WARNING - To reduce the risk of fire or elec-

trical shock, do not expose this product to

rain, moisture or other liquids. Do not touch

the TV with wet hands. Do not install this

product near flammable objects such as

gasoline or candles or expose the TV to

direct air conditioning.

Do not expose to dripping or splashing and

do not place objects filled with liquids, such

as vases, cups, etc. on or over the appara-

tus (e.g. on shelves above the unit).

GROUNDING

Ensure that you connect the earth ground

wire to prevent possible electric shock (i.e. a

TV with a three-prong grounded AC plug

must be connected to a three-prong ground-

ed AC outlet). If grounding methods are not

possible, have a qualified electrician install a

separate circuit breaker.

Do not try to ground the unit by connecting it

to telephone wires, lightening rods, or gas

pipes.

Power

Supply

Short-circuit

Breaker

DISCONNECTING DEVICE FROM MAINS

Mains plug is the disconnecting device. The

plug must remain readily operable.

As long as this unit is connected to the AC

wall outlet, it is not disconnected from AC

power even if you turn off the power switch

on the unit.

ANTENNAS

Outdoor antenna grounding

If an outdoor antenna is installed, follow the

precautions below. An outdoor antenna sys-

tem should not be located in the vicinity of

overhead power lines or other electric light or

power circuits, or where it can come in contact

with such power lines or circuits as death or

serious injury can occur.

Be sure the antenna system is grounded so as

to provide some protection against voltage

surges and built-up static charges.

Section 810 of the National Electrical Code

(NEC) in the U.S.A. provides information with

respect to proper grounding of the mast and

supporting structure, grounding of the lead-in

wire to an antenna discharge unit, size of

grounding conductors, location of antenna

discharge unit, connection to grounding elec-

trodes and requirements for the grounding

electrode.

Antenna grounding according to the National

Electrical Code, ANSI/NFPA 70

Antenna Lead in Wire

Antenna Discharge Unit

(NEC Section 810-20)

Grounding Conductor

(NEC Section 810-21)

Ground Clamps

Power Service Grounding

Electrode System (NEC

Art 250, Part H)

Ground Clamp

Electric Service

Equipment

NEC: National Electrical Code

Cleaning

When cleaning, unplug the power cord and

rub gently with a soft cloth to prevent

scratching. Do not spray water or other liquids

directly on the TV as electric shock may occur.

Do not clean with chemicals such as alcohol,

thinners or benzene.

Moving

Make sure the product is turned off, unplugged

and all cables have been removed. It may take

2 or more people to carry larger TVs. Do not

press against or put stress on the front panel

of the TV.

Ventilation

Install your TV where there is proper ventila-

tion. Do not install in a confined space such

as a bookcase. Do not cover the product

with cloth or other materials (e.g.) plastic

while plugged in. Do not install in exces-

sively dusty places.

Take care not to touch the ventilation open-

ings. When watching the TV for a long

period, the ventilation openings may

become hot.

If you smell smoke or other odors coming

from the TV or hear strange sounds, unplug

the power cord contact an authorized service

center.

Do not press strongly upon the panel with

hand or sharp object such as nail, pencil or

pen, or make a scratch on it.

Keep the product away from direct sunlight.

For LED LCD TV

If the TV feels cold to the touch, there may be

a small “flicker” when it is turned on. This is

normal, there is nothing wrong with TV.

Some minute dot defects may be visible on

the screen, appearing as tiny red, green, or

blue spots. However, they have no adverse

effect on the monitor's performance.

Avoid touching the LCD screen or holding

your finger(s) against it for long periods of

time. Doing so may produce some tempo-

rary distortion effects on the screen.

ŹWarning for photosensitization seizure:

Some viewers may experience a seizure

or epilepsy when exposed to certain fac-

tors, including ﬂashing lights or images in

TV or video games. If you or anybody from

your family has a history of epilepsy or sei-

zure, please consult with your doctor before

watching 3D TV.

Also certain symptoms can occur in un-

speciﬁed conditions without any previous

history. If you experience any of the follow-

ing symptoms, immediately stop watching

the 3D imaging and consult a doctor: dizzi-

ness or lightheadedness, visual transition or

altered vision, visual or facial instability, such

as eye or muscle twitching, unconscious ac-

tion, convulsion, loss of conscience, con-

fusion or disorientation, loss of directional

sense, cramps, or nausea. Parents should

monitor their children, including teenagers,

for these symptoms as they may be more

sensitive to the effects of watching 3D TV.

Risk of photosensitization seizure can be re-

duced with the following actions.

- Take frequent breaks from watching 3D TV.

- For those who have vision that is different

in each eye, they should watch the TV af-

ter taking vision correction measures.

- Watch the TV so that your eyes are on the

same level as the 3D screen and refrain

from sitting too closely to the TV

- Do not watch the 3D imaging when tired or

sick, and avoid watching the 3D imaging

for a long period of time.

- Do not wear the 3D glasses for any other

purpose than viewing 3D imaging on a 3D

TV.

- Some viewers may feel disoriented after

watching 3D TV. Therefore, after you watch

3D TV, take a moment to regain awareness of

your situation before moving.

Viewing 3D Imaging

ŹWhen viewing 3D imaging, watch the

TV from an effective viewing angle and

within the appropriate distance. If you ex-

ceed this viewing angle or distance, you

may not be able to view the 3D imaging.

Furthermore, the 3D imaging may not

display if it is viewed while you are lying

down.

ŹIf you watch the 3D imaging too closely

or for a long period of time, it may harm

your eyesight.

ŹWatching the TV or playing video games

that incorporate 3D imaging with the

3D glasses for a long period of time can

cause drowsiness, headaches or fatigue

to you and/or your eyes. If you have a

headache, or otherwise feel fatigued or

drowsy, stop watching the TV and take a

rest.

ŹPregnant woman, seniors, persons with

heart problems or persons who experi-

ence frequent drowsiness should refrain

from watching 3D TV.

ŹSome 3D imaging may cause you to duck

or dodge the image displayed in the video.

Therefore, it is best if you do not watch 3D

TV near fragile objects or near any objects

that can be knocked over easily.

Ź Please prevent children under the age of

5 from watching 3D TV. It may affect their

vision development.

SAFETY INSTRUCTIONS

WARNING / CAUTION

............................2

SAFETY INSTRUCTIONS

........................3

CONTENTS

......................................................6

FEATURE OF THIS TV

..............................9

PREPARATION

Accessories...........................................................10

Optional Extras ..................................................... 11

Front Panel Information .................................... 12

Back Panel Information.....................................15

Stand Instructions

......................................................18

VESA Wall Mounting ........................................22

Cable Management ..........................................24

Desktop Pedestal Installation .........................26

Swivel Stand ........................................................26

Kensington Security System ..........................26

Securing the TV to the wall to prevent falling

when the tv is used on a stand..................... 27

Antenna or Cable Connection.......................28

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup............................................29

DVD SETUP.........................................................33

VCR SETUP.........................................................36

Other A/V Source Setup.................................38

USB Connection ................................................38

Headphone Setup

....................................................39

Audio Out Connection.....................................40

External Equipment WIreless Connection

(Optional Extras).................................................. 41

PC Setup..............................................................42

Network Setup .................................................... 47

WATCHING TV / CHANNEL CONTROL

Remote Control Functions ..............................55

Magic Motion Remote Control Functions...58

Turning on the TV............................................... 61

Channel Selection............................................... 61

Volume Adjustment ........................................... 61

Initial Setting .......................................................62

On-Screen Menus Selection ..........................64

Quick Menu .........................................................66

Home Menu ........................................................ 67

Customer Support

- Software Update.............................................68

- Picture Test/Sound Test................................ 69

- Product/Service Info...................................... 70

- Network Test...................................................... 71

Simple Manual.................................................... 72

Channel Setup

- Auto Scan (Auto Tuning).............................. 73

- Add/Delete Channel (Manual Tuning) ..... 74

- Channel Editing............................................... 75

Channel List ........................................................ 76

Favorite Channel Setup.................................... 77

Channel Information ......................................... 78

Channel Brief Information............................... 79

Input List ............................................................. 80

Input Label............................................................81

Reset to Factory Default (Initial Setting) .....82

Mode Setting ......................................................83

Demo Mode ........................................................84

AV Mode...............................................................85

Game/Schedule.................................................86

SIMPLINK.............................................................90

3D VIDEO

3D Video...............................................................92

Watching 3D Video ...........................................94

MY MEDIA

Entry Mode ..........................................................96

Connection Method .......................................... 97

Movie list............................................................. 102

Photo list............................................................. 109

Music list.............................................................. 115

DivX Registration Code.................................. 120

Deactivation ........................................................ 121

NETWORK

Legal Notice ...................................................... 122

CONTENTS

NETCAST

Netcast Menu.................................................... 123

YOUTUBE........................................................... 124

PICASA............................................................... 126

PICTURE CONTROL

Picture Size (Aspect Ratio) Control............ 128

Picture Wizard...................................................130

ᰚEnergy Saving ............................................ 132

Preset Picture Settings (Picture Mode)..... 133

Manual Picture Adjustment - User Mode 134

Picture Improvement Technology (Advanced

Control) ............................................................... 135

Expert Picture control..................................... 136

Picture Reset..................................................... 139

TruMotion .........................................................140

LED Local Dimming ........................................141

Power Indicator ................................................ 142

Image Sticking Minimization (ISM) Method

.143

SOUND & LANGUAGE CONTROL

Auto Volume...................................................... 144

Clear Voice II ..................................................... 145

Balance ............................................................... 146

Preset Sound Settings (Sound Mode) .......147

Sound Setting Adjustment - User Mode. 148

Audio Reset....................................................... 149

TV Speakers On/Off Setup ..........................150

Stereo/SAP Broadcast Setup ....................... 151

Audio Language ............................................. 152

On-screen Menus Language Selection.... 153

Caption Mode

- Analog Broadcasting System Captions . 154

- Digital Broadcasting System Captions... 155

- Caption Option.............................................. 156

TIME SETTING

Clock Setting

- Auto Clock Setup ..........................................157

- Manual Clock Setup .................................... 158

Auto On/Off Time Setting ............................ 159

Sleep Timer Setting ........................................ 160

PARENTAL CONTROL / RATINGS

Set Password & Lock System

- Setting up Your Password............................161

- Set Password ................................................. 162

Lock System...................................................... 163

Channel Blocking............................................. 164

Movie & TV Rating .......................................... 165

Downloadable Rating.......................................170

External Input Blocking ....................................171

Key Lock ..............................................................172

APPENDIX

Troubleshooting.................................................173

Maintenance.......................................................176

Product Specifications ....................................177

IR Codes.............................................................180

External Control Through RS-232C .......... 182

Open Source License.....................................188

FEATURE OF THIS TV

IMPORTANT INFORMATION TO PREVENT “IMAGE

BURN / BURN-IN” ON YOUR TV SCREEN

ᯫ

Some of these features are not available on all models.

This TV contains the detailed calibra-

tions necessary for professional certifi-

cation by the Imaging Science

Foundation. The resulting ISF “day” and

“night” modes will then be accessible

by the user to experience the best their

LG HDTV has to offer.

Sophisticated and detailed calibrations

can be made through the ISFccc mode.

Detailed calibration requires a licensed

technician.

Please contact your local dealer to

inquire about an ISF certified technician.

THX (Thomlinson Holman’s Experiment)

is an audio and video certification stan-

dard established by George Lucas and

Thomlinson. A THX certified display

guarantees screen quality that exceeds

the display standard specification in

both hardware and software.

View videos and photos and listen to

music on your TV through USB 2.0

(‘videos’ dependent on model).

Displays HDTV programs in full 1920 x

1080p resolution for a more detailed

picture.

ᯫ

When a fixed image (e.g. logos, screen menus, video game, and computer display) is displayed

on the TV for an extended period, it can become permanently imprinted on the screen. This

phenomenon is known as “image burn” or “burn-in.” Image burn is not covered under the man-

ufacturer’s warranty.

ᯫ

In order to prevent image burn, avoid displaying a fixed image on your TV screen for a prolonged

period (2 or more hours for LCD, 1 or more

hours for Plasma).

ᯫ

Image burn can also occur on the letter-

boxed areas of your TV if you use the 4:3

aspect ratio setting for an extended period.

High-definition television. High-

resolution digital television broadcast

and playback system composed of

roughly a million or more pixels, 16:9

aspect-ratio screens, and AC3 digital

audio. A subset of digital television,

HDTV formats include 1080p, 1080i,

and 720p resolutions.

Manufactured under license from Dolby

Laboratories. “Dolby “and the double-D

symbol are trademarks of Dolby

Laboratories.

HDMI, the HDMI logo and High-

Definition Multimedia Interface are

trademarks or registered trademarks of

HDMI Licensing LLC."

ABOUT DIVX VIDEO: DivX® is a digital

video format created by DivX,Inc. This is

an official DivX Certified device that

plays DivX video. Visit www.divx.com for

more information and software tools to

convert your files into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND:

This DivX Certified® device must be

registered in order to play DivX Video-

on-Demand (VOD) content. To gener-

ate the registration code, locate the

DivX VOD section in the device setup

menu. Go to vod.divx.com with this

code to complete the registration pro-

cess and learn more about DivX VOD.

“DivX Certified to play DivX video up to

HD 1080p, including premium content”

“Pat. 7,295,673; 7,460,688;7,519,274”

PREPARATION

ACCESSORIES

PREPARATION

Ensure that the following accessories are included with your TV. If an accessory is missing, please con-

tact the dealer where you purchased the TV.

The accessories included may differ from the images below.

Option Extras

* Wipe spots on the exterior only with the

polishing cloth.

* Do not wipe roughly when removing

stains. Excessive pressure may cause

scratches or discoloration.

Polishing Cloth

Not included with all models

D-sub 15 pin Cable

When using the VGA (D-sub 15

pin cable) PC connection, the user

must use shielded signal interface

cables with ferrite cores to main-

tain standards compliance.

1.5V 1.5V

Owner’s Manual CD Manual,

Nero MediaHome 4

Essentials CD

Remote Control,

Batteries (AAA)

Motion Remote Control,

Strap,

Batteries (AA)

Ferrite Core

(Black)

Ferrite Core

(White)

Close to the wall plug.

Ferrite core can be used to reduce the electromagnetic

waves that may interfere with the TV. Install the Ferrite

core on the power cable close to the wall plug.

Ferrite core can be used to reduce the electromagnetic

wave when connecting the LAN cable. Place the ferrite

core far from TV and wind the LAN cable in the ferrite

core once.

1.5V 1.5V

PREPARATION

OPTIONAL EXTRAS

Optional extras can be changed or modified for quality improvement without any notification.

Contact your dealer for buying these items.

These devices only work with compatible LG LED LCD TV and Plasma TV.

Wireless Media Box

(AN-WL100W)

Wireless LAN for Broadband/

DLNA Adaptor

(AN-WF100)

47/55LX9500, 47/55LEX8, 60/72LEX9

Cable Holder

(Refer to p.25)

Component gender cable,

AV gender cable

Screws for stand assembly

(Refer to P.20)

x 4 x 4 x 2

(M4 x 12) (M4 x 22)

Plasma TV

Protection Cover

(Refer to P.19)

Cable Holder

(Refer to P.24)

x 2

Screws for stand assembly

(Refer to P.18)

(For 50PK950, 50PX950)

x 4 x 4

(M4 x 14) (M4 x 28)

Power Cord Cable

Management Clip

(Refer to P.24)

Wireless LAN for

Broadband/DLNA Adaptor

(AN-WF100)

Stand Rear Cover

3D Glasses

(AG-S100)

(For 47/55LX9500, 50/60PX950)

PREPARATION

ᯫ

Image shown may differ from your TV.

FRONT PANEL INFORMATION

50/60PK950, 50/60PX950

SPEAKER

Remote Control Sensor

Intelligent Sensor

Adjusts picture according to the

surrounding conditions

Touch Button

You can operate the button just by touching the button lightly with your finger.

ENTER CH

VOL

INPUT

CHANNEL

(ᰜ,ᰝ)

Buttons

VOLUME

(+, -)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

Power/Standby Indicator

Illuminates red in standby mode.

The lighting is off while the TV remains on.

PREPARATION

47/55LX9500

SPEAKER

Emitter

It is the part equipped with

the emitter exchanging sig-

nal with 3D glasses.

Please be careful not to

block the screen with objects

or people while watching a

3D Video.

Remote Control Sensor

Intelligent Sensor

Adjusts picture according to

the surrounding conditions

VOL

ENTER

INPUT

CHANNEL (ᰝ,ᰜ)

Buttons

VOLUME (-, +)

Buttons

ENTER Button

INPUT Button

MENU Button

POWER Button

Power/Standby Indicator

(Can be adjusted using the Power Indicator

in the OPTION menu.Źp.142)

PREPARATION

ᯫ

Image shown may differ from your TV.

47/55LEX8, 60/72LEX9

SPEAKER

Power/Standby Indicator

(Can be adjusted using the Power Indicator in

the OPTION menu.Źp.142)

Remote Control Sensor

VOL ENTERCH MENU INPUT

CHANNEL

(ᰝ,ᰜ)

Buttons

VOLUME

(-, +)

Buttons

ENTER

Button

INPUT

Button

POWER

Button

Touch Button

You can operate the button just by touching the button lightly with your finger.

Intelligent Sensor

Adjusts picture according to

the surrounding conditions

Emitter

PREPARATION

BACK PANEL INFORMATION

ᯫ

Image shown may differ from your TV.

ANTENNA

/CABLE

RGB IN (PC)

LAN

WIRELESS

CONTROL

REMOTE CONTROL IN

AUDIO IN

(RGB/DVI)

PTICAL

DIGITAL

AUDIO OUT

/DVI IN

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT IN

AV IN 1

YLR

RS-232C IN

(CONTROL &

SERVICE)

DVI IN 4

USB IN 1 USB IN 2

AV IN 2

VIDEO

AUDIO

L(MONO)

50/60PK950, 50/60PX950

2 3 45

7813

SERVICE ONLY

PREPARATION

47/55LX9500, 47/55LEX8, 60/72LEX9

ANTENNA/

CABLE IN

RGB IN (PC)

LAN

WIRELESS

CONTROL

(RGB/DVI)

OPTICAL DIGITAL

/DVI IN

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT INAV IN 1

L R

AUDIO IN

AUDIO OUT

RS-232C IN

(CONTROL&

SERVICE)

ꔡ

1 2 3 4

8 79

COMPONENT IN3

AUDIO / Y P

IN 4

H/P USB IN 1 USB IN 2

AV IN2

VIDEO / AUDIO

CAUTION

For HDMI IN 4 and USB IN 1, 2

ŹFor an optimal connection,

HDMI cables and USB

devices should have bezels

less than 10 mm (0.39

inches) thick.

*A 10 mm (0.39 inches)

PREPARATION

1LAN

Network connection for Netflix, Yahoo! TV

Widgets, etc (for USA).

Also used for video, photo and music files on

a local network.

2HDMI/DVI IN, HDMI IN

Digital Connection.

Supports HD video and Digital audio. Doesn’t

support 480i.

Accepts DVI video using an adapter or HDMI

to DVI cable (not included).

3RGB IN (PC)

Analog PC Connection. Uses a D-sub 15 pin

cable (VGA cable).

AUDIO IN (RGB/DVI)

0.32 cm (1/8 inch) headphone jack for analog

PC audio input.

4RS-232C IN (CONTROL & SERVICE) or

SERVICE ONLY

Used by third party devices.

This port is used for service or Hotel mode.

5OPTICAL DIGITAL AUDIO OUT

Digital optical audio output for use with amps

and home theater systems.

Note: In standby mode, this port doesn’t work.

6AV (Audio/Video) IN

Analog composite connection.

Supports standard definition video only (480i).

7ANTENNA/CABLE IN

Connect over-the-air or cable signals to this

jack.

8COMPONENT IN

Analog Connection.

Supports HD.

Uses a red, green, and blue cable for video &

red and white for audio.

9WIRELESS CONTROL

Connect the Wireless Ready Dongle to the TV

to control the external input devices con-

nected to Media Box wirelessly.

10 USB INPUT

Used for viewing photos, watching movies

and listening to MP3s.

11 HEADPHONE

0.32 cm (1/8 inch) headphone jack

Impedance 16 Ω , Maximum audio out 15 mW

12 Power Cord or Socket

For operation with AC power.

Caution: Never attempt to operate the TV on

DC power.

13 REMOTE CONTROL IN

For a wired remote control.

PREPARATION

STAND INSTRUCTIONS

(For 50/60PK950, 50/60PX950)

ᯫ

Image shown may differ from your TV.

INSTALLATION

NOTE

ŹWhen assembling the desk type stand,

make sure the screws are fully tightened (If

not tightened fully, the TV can tilt forward

after the product installation). Do not over

tighten.

1Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

2Assemble the parts of the STAND BODY

with the STAND BASE of the TV.

3Assemble the parts of the CABLE

MANAGEMENT CLIP with the STAND

BODY.

5Install the 4 screws into the holes shown.

M4 x 28

4Assemble the TV as shown.

STAND BASE

STAND BODY

CABLE

MANAGEMENT

CLIP

M4 x 14

50PK950, 50PX950

(provided as parts of the product)

PREPARATION

DETACHMENT

PROTECTION COVER

After removing the stand, install the included

PROTECTION COVER over the hole for the

stand.

Press the PROTECTION COVER into the TV until

you hear it click.

When installing the wall mounting bracket, use

the PROTECTION COVER.

1Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

2Remove the screws that

hold the stand on.

3Detach the stand from TV.

PROTECTION COVER

Fix a guide to the outside.

50PK950, 50PX950 60PK950, 60PX950

M4 x 30

M4 x 28

PREPARATION

STAND INSTRUCTIONS

(For 47/55LX9500, 47/55LEX8)

ᯫ

Image shown may differ from your TV.

INSTALLATION

NOTE

ŹWhen assembling the desk type stand,

make sure the screws are fully tightened (If

not tightened fully, the TV can tilt forward

after the product installation). Do not over

tighten.

2Assemble the parts of the STAND

BODY with the STAND BASE of the

TV.

At this time, tighten the screws that

hold the STAND BODY on.

1Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

4Assemble the part of the STAND

REAR COVER with the TV.

3Install the 4 screws into the holes shown.

M4 x 22

M4 x 12

STAND BODY

STAND BASE

STAND REAR

COVER

PREPARATION

DETACHMENT

1Carefully place the TV screen side down on

a cushioned surface to protect the screen

from damage.

3Remove the screws that hold the stand on.

2Detach the STAND REAR COVER from TV.

4Detach the stand from TV.

PREPARATION

VESA WALL MOUNTING

Install your wall mount onto wooden studs perpendicular to the floor. When attaching to other building

materials, please contact a professional.

If installed on a ceiling or slanted wall, it may fall and result in severe personal injury.

We recommend that you use an LG brand wall mount when mounting the TV to a wall.

LG recommends that wall mounting be performed by a qualified professional installer.

Model

VESA (A * B)

Standard

Screw Quantity Wall Mounting Bracket

(sold separately)

47LX9500,

47LEX8 200 * 200 M6 4

LSW200B, LSW200BG,

LSW200BX, LSW200BXG

55LX9500,

55LEX8 400 * 400 M6 4

LSW400B, LSW400BG,

DSW400BG

50PK950,

50PX950 400 * 400 M6 4

AW-50PG60M AW-50PG60MS

60PK950,

60PX950 600 * 400 M8 4

AW-60PG60M AW-60PG60MS

PREPARATION

CAUTION

ŹDo not install your wall mount kit while your TV is turned on. It may result in personal injury due to

electric shock.

NOTE

ŹScrew length needed depends on the wall

mount used. For further information, refer to

the instructions included with the mount.

ŹStandard dimensions for wall mount kits are

shown in the table.

ŹWhen purchasing our wall mount kit, a detailed

installation manual and all parts necessary for

assembly are provided.

ŹDo not use screws longer than the standard

dimension, as they may cause damage to the

inside to the TV.

ŹFor wall mounts that do not comply with the

VESA standard screw specifications, the length

of the screws may differ depending on their

specifications.

ŹDo not use screws that do not comply with the

VESA standard screw specifications.

Do not use fasten the screws too strongly, this

may damage the TV or cause the TV to a fall,

leading to personal injury. LG is not liable for

these kinds of accidents.

ŹLG is not liable for TV damage or personal

injury when a non-VESA or non specified wall

mount is used or the consumer fails to follow

the TV installation instructions.

PREPARATION

CABLE MANAGEMENT

ᯫ

Image shown may differ from your TV.

Plasma TV

How to use the CABLE HOLDER

How to use the CABLE MANAGEMENT CLIP

1Connect the cables as necessary.

To connect additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

2Install the CABLE MANAGEMENT CLIP

into the TV until clicking sound.

HOW TO REMOVE THE CABLE

MANAGEMENT CLIP

ŹHold the CABLE MANAGEMENT CLIP with

both hands and pull it backward as shown.

1After connecting the cables as necessary, install the CABLE HOLDER as shown and bundle the

cables.

In case of the LAN cable, install as shown to reduce the electromagnetic wave.

CABLE HOLDER

PREPARATION

ᯫ

Image shown may differ from your TV.

47/55LX9500, 47/55LEX8, 60/72LEX9

CABLE HOLDER

2After connecting the cables as necessary,

install the CABLE HOLDER as shown

and bundle the cables.

1Secure the power cord with the CABLE

HOLDER on the TV back cover.

It will help prevent the power cable from

being removed by accident.

PREPARATION

DESKTOP PEDESTAL INSTALLATION

SWIVEL STAND

After installing the TV, you can adjust the TV set manually to the left or right direction by 20 º to suit

your viewing position.

ᯫ

Image shown may differ from your TV.

For proper ventilation, allow a clearance of 10.1 cm (4 inch) on all four sides from the wall.

10.1 cm (4 inch)

CAUTION

ŹEnsure adequate ventilation by following the clearance recommendations.

ŹDo not mount near or above any type of heat source.

KENSINGTON SECURITY SYSTEM

ᯫ

This feature is not available for all models.

- The TV is equipped with a Kensington Security System con-

nector on the back panel. Connect the Kensington Security

System cable as shown below.

- For the detailed installation and use of the Kensington Security

System, refer to the user’s guide provided with the Kensington

Security System.

For further information, contact http://www.kensington.com,

the internet homepage of the Kensington company. Kensington

sells security systems for expensive electronic equipment such

as notebook PCs and LCD projectors.

NOTE: The Kensington Security System is an optional accessory.

PREPARATION

SECURING THE TV TO THE WALL TO PREVENT FALLING

WHEN THE TV IS USED ON A STAND

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.

Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward

direction, potentially causing injury or damaging the product.

Caution: Please make sure that children don’t climb on or hang from the TV.

ᯫ

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the

picture.

* If your product has the bolts in the eye-bolts position before inserting the eye-bolts, loosen the

bolts.

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (sold separately) to the wall. Match the height of the bracket

that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

ᯫ

Use a sturdy rope (sold separately) to tie the product. It is safer to tie the

rope so it becomes horizontal between the wall and the product.

ᯫ

You should purchase necessary components to prevent the TV from tipping over (when not using a

wall mount).

ᯫ

Image shown may differ from your TV.

NOTE

ŹUse a platform or cabinet strong enough and large enough to support the size and weight of

the TV.

ŹTo use the TV safely make sure that the height of the bracket on the wall and the one on the TV are

the same.

PREPARATION

ANTENNA OR CABLE CONNECTION

ᯫ

To prevent damage do not connect to the power outlet until all connections are made between the

devices.

ᯫ

Image shown may differ from your TV.

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wall

Antenna

Socket

Outdoor

Antenna

(VHF, UHF)

Cable TV

Wall Jack

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

RF Coaxial Wire (75 Ω)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Be careful not to bend the copper wire

when connecting the antenna.

Copper Wire

ᯫ

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

ᯫ

For much more information about antennas visit our Knowledgebase at http://lgknowledgebase.

com. Search for antenna.

ANTENNA/

CABLE IN

ANTENNA/

CABLE IN

EXTERNAL EQUIPMENT SETUP

HD RECEIVER SETUP

ᯫ

To prevent the equipment damage, never plug in any power cords until you have finished connecting all

equipment.

ᯫ

mage shown may differ from your TV.

1. How to connect

1Connect the video outputs (Y, P B, PR) of the

digital set-top box to the COMPONENT IN

VIDEO 1, 2,or3* jacks on the TV. Match the

jack colors (Y = green, PB = blue, and PR = red).

2Connect the audio output of the digital set-top

box to the COMPONENT IN AUDIO 1, 2,or3*

jacks on the TV.

2. How to use

ᯫ

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-

top box operation.)

ᯫ

Select the Component1,Component2, or

Component3 input source on the TV using the

INPUT button on the remote control.

Component Connection

This TV can receive digital over-the-air/digital cable signals without an external digital set-top box.

However, if you do receive digital signals from a digital set-top box or other digital external device.

EXTERNAL EQUIPMENT SETUP

RGB IN (PC)

(RGB/DVI)

RS-232C IN

(CONTROL&

SERVICE)

OPTICAL

DIGITAL

/DVI IN

VIDEO

AUDIO

L(MONO)

AV IN 1

AUDIO IN

AUDIO OUT

VIDEO AUDIO

COMPONENT IN

L R

Y L RP

1 2

Y, C B/PB, CR/PR

Resolution Horizontal

Frequency(KHz)Vertical

Frequency(Hz)

720x480i 15.73 59.94

15.73 60.00

720x480p 31.47 59.94

31.50 60.00

1280x720p 44.96 59.94

45.00 60.00

1920x1080i

33.72 59.94

33.75 60.00

1920x1080p

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

* Component3: For LED LCD TV

EXTERNAL EQUIPMENT SETUP

YLR P

AUDIO / Y P

IN 4

H/P USB IN 1 USB IN 2

AV IN2

VIDEO / AUDIO

COMPONENT IN3

For LED LCD TV

EXTERNAL EQUIPMENT SETUP

HDMI Connection

1. How to connect

1Connect the digital set-top box to HDMI/DVI IN

1,2,3, or 4jack on the TV.

2No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

ᯫ

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-

top box.)

ᯫ

Select the HDMI1,HDMI2,HDMI3, or HDMI4 input

source on the TV using the INPUT button on the

remote control.

NOTE

ŹIf an HDMI cable doesn’t support High Speed HDMI,

it can cause flickers or no screen display. In this case

use the latest cables that support High Speed HDMI.

ŹHDMI Audio Supported Format: Dolby Digital (32 KHz, 44.1

KHz, 48 KHz), Linear PCM (32 KHz, 44.1 KHz, 48 KHz)

HDMI-DTV

Resolution Horizontal

Frequency(KHz)Vertical

Frequency(Hz)

720x480p 31.47 59.94

31.50 60.00

1280x720p 44.96 59.94

45.00 60.00

1920x1080i

33.72 59.94

33.75 60.00

1920x1080p

26.97 23.976

27.00 24.00

33.71 29.97

33.75 30.00

67.432 59.94

67.50 60.00

HDMI OUTPUT

RGB IN (PC)

LAN

WIRELESS

CONTROL

(RGB/DVI)

VIDEO

L(MONO)

VIDEO A

AUDIO IN

AUDIO OUT

/DVI IN

OPTICAL DIGITAL

RS-232

(CONTROL&

ꔡ

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

1. How to connect

1Connect the DVI output of the digital set-top

box to the HDMI/DVI IN 1,2,3, or 4* jack on

the TV.

2Connect the digital set-top box audio output to

the AUDIO IN (RGB/DVI) jack on the TV.

2. How to use

ᯫ

Turn on the digital set-top box.

(Refer to the owner’s manual for the digital set-

top box.)

ᯫ

Select the HDMI1,HDMI2,HDMI3, or HDMI4* input

source on the TV using the INPUT button on the

remote control.

NOTE

ŹA DVI to HDMI cable or adapter is required for this con-

nection. DVI doesn't support audio, so a separate audio

connection is necessary.

L R

DVI OUTPUT

AUDIO

RGB IN (PC)

LAN

WIRELESS

CONTROL

RS-232C IN

(CONTROL&

SERVICE)

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT

INAV

L R

AUDIO OUT

/DVI IN

(RGB/DVI)

AUDIO IN

OPTICAL DIGITAL

ꔡ

* HDMI4: For Plasma TV

EXTERNAL EQUIPMENT SETUP

DVD SETUP

Component Input ports

To get better picture quality, connect a DVD player

to the component input ports as shown below.

1. How to connect

1Connect the video outputs (Y, P B, PR) of the

DVD to the COMPONENT IN VIDEO 1, 2,or3*

jacks on the TV.

Match the jack colors (Y = green, PB = blue, and

PR = red).

2Connect the audio outputs of the DVD to the

COMPONENT IN AUDIO 1, 2,or3* jacks on the

TV.

2. How to use

ᯫ

Turn on the DVD player, insert a DVD.

ᯫ

Select the Component1, Component2, or

Component3 input source on the TV using the

INPUT button on the remote control.

ᯫ

Refer to the DVD player’s manual for operating

instructions.

Component Connection

RGB IN (PC)

(RGB/DVI)

/DVI IN

VIDEO

AUDIO

L(MONO)

AV IN 1

AUDIO IN

AUDIO OUT

VIDEO AUDIO

COMPONENT IN

L R

Y L RP

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

* Component3: For LED LCD TV

Component ports on

the TV

Video output ports

on DVD player

YB-YR-Y

YCbCr

YPb Pr

YLR P

AUDIO / Y P

IN 4

H/P USB IN 1 USB IN 2

AV IN2

VIDEO / AUDIO

COMPONENT IN3

For LED LCD TV

EXTERNAL EQUIPMENT SETUP

Composite (RCA) Connection

1. How to connect

1Connect the AUDIO/VIDEO jacks between TV

and DVD. Match the jack colors (Video = yellow,

Audio Left = white, and Audio Right = red)

2. How to use

ᯫ

Turn on the DVD player, insert a DVD.

ᯫ

Select the AV1 or AV2 input source on the TV

using the INPUT button on the remote control.

ᯫ

Refer to the DVD player's manual for operating

instructions.

RGB IN (PC)

(RGB/DVI)

/DVI IN

VIDEO AUDIO

COMPONENT IN

AUDIO IN

AUDIO OUT

VIDEO

AUDIO

L(MONO)

AV IN 1

L R

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

L R

VIDEO

AUDIO

L R

VIDEO

AUDIO

AUDIO / Y P

IN 4

H/P USB IN 1 USB IN 2

VIDEO / AUDIO

COMPONENT IN3

AV IN2

For LED LCD TV

EXTERNAL EQUIPMENT SETUP

HDMI OUTPUT

RGB IN (PC)

LAN

WIRELESS

CONTROL

(RGB/DVI)

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT INAV IN 1

AUDIO IN

AUDIO OUT

/DVI IN

L R

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

ꔡ

HDMI Connection

1. How to connect

1Connect the HDMI output of the DVD to the

HDMI/DVI IN 1,2,3or 4 jack on the TV.

2No separate audio connection is necessary.

HDMI supports both audio and video.

2. How to use

ᯫ

Select the HDMI1,HDMI2,HDMI3, or HDMI4 input

source on the TV using the INPUT button on the

remote control.

ᯫ

Refer to the DVD player's manual for operating

instructions.

NOTE

ŹIf an HDMI cable doesn’t support High Speed HDMI,

it can cause flickers or no screen display. In this case

use the latest cables that support High Speed HDMI.

ŹHDMI Audio Supported Format: Dolby Digital (32 KHz, 44.1

KHz, 48 KHz), Linear PCM (32 KHz, 44.1 KHz, 48 KHz)

EXTERNAL EQUIPMENT SETUP

VCR SETUP

Antenna Connection

ANTENNA/

CABLE IN

L R

S-VIDEO VIDEO

AUDIO

OUTPUT

SWITCH

ANT IN

ANT OUT

Wall Jack

Antenna

1. How to connect

1Connect the RF antenna out socket

of the VCR to the ANTENNA/CABLE

IN socket on the TV.

2Connect the antenna cable to the RF

antenna in socket of the VCR.

2. How to use

ᯫ

Set VCR output switch to 3 or 4 and

then tune TV to the same channel num-

ber.

ᯫ

Insert a video tape into the VCR and

press PLAY on the VCR (Refer to the

VCR owner’s manual).

EXTERNAL EQUIPMENT SETUP

Composite (RCA) Connection

S-VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

RGB IN (PC)

(RGB/DVI)

/DVI IN

VIDEO AUDIO

COMPONENT IN

AUDIO IN

AUDIO OUT

VIDEO

AUDIO

L(MONO)

AV IN 1

L R

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

L R

VIDEO

AUDIO

1. How to connect

1Connect the AUDIO/VIDEO jacks between TV

and VCR. Match the jack colors (Video = yellow,

Audio Left = white, and Audio Right = red)

2. How to use

ᯫ

Insert a video tape into the VCR and press PLAY

on the VCR. (Refer to the VCR owner’s manual.)

ᯫ

Select the AV1 or AV2 input source on the TV

using the INPUT button on the remote control.

NOTE

ŹIf you have a mono VCR, connect the audio cable

from the VCR to the AUDIO L/MONO jack of the TV.

S-VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

L R

VIDEO

AUDIO

AUDIO / Y P

IN 4

H/P USB IN 1 USB IN 2

VIDEO / AUDIO

COMPONENT IN3

AV IN2

For LED LCD TV

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

1. How to connect

1Connect the AUDIO/VIDEO jacks

between TV and external equipment.

Match the jack colors

(Video = yellow, Audio Left = white, and

Audio Right = red)

2. How to use

ᯫ

Select the AV1 or AV2 input source on

the TV using the INPUT button on the

remote control.

ᯫ

Operate the corresponding external

equipment.

USB CONNECTION

IN 4

USB IN 1 USB IN 2

Memory Key

1. How to connect

1Connect the USB device to the USB

IN 1 or 2 jack on the side of TV.

2. How to use

ᯫ

After connecting the USB IN jack, you

use the USB function. (Źp.97)

AV IN 2

VIDEO

AUDIO

L(MONO)

H/P

IN 4

USB IN 1 USB IN 2

L R

VIDEO

Camcorder

Video Game Set

EXTERNAL EQUIPMENT SETUP

HEADPHONE SETUP (FOR LED LCD TV)

H/P

You can listen to the sound through headphones.

1. How to connect

1Plug headphones into the head-

phone socket.

2To adjust the headphone volume,

press the VOL +/- button. If you

press the MUTE button, the sound

from the headphone is switched off.

NOTE

ŹAUDIO menu options are disabled when connecting

headphones.

ŹWhen changing AV MODE with headphones connect-

ed, the change is applied to video but not to audio.

ŹOptical Digital Audio Out is not available with head-

phones connected.

EXTERNAL EQUIPMENT SETUP

RGB

(PC)

LESS

TROL

(RGB/DVI)

/DVI IN

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT INAV IN 1

AUDIO IN

AUDIO OUT

L R

OPTICAL DIGITAL

(CONTROL&

SERVICE)

AUDIO OUT CONNECTION

Send the TV’s audio to external audio equipment via the Audio Output port.

If you want to enjoy digital broadcasting through 5.1-channel speakers, connect the OPTICAL DIGITAL

AUDIO OUT terminal on the back of TV to a Home Theater (or amp).

NOTE

ŹWhen connecting with external audio equipment, such

as amplifiers or speakers, you can turn the TV speakers

off in the menu. (Źp.150)

CAUTION

ŹDo not look into the optical output port. Looking at

the laser beam may damage your vision.

ŹAudio with ACP (Audio Copy Protection) function may

block digital audio output.

1. How to connect

1Connect one end of the optical cable to the

TV port of OPTICAL DIGITAL AUDIO OUT.

2Connect the other end of the optical cable to

the digital audio input on the audio equip-

ment.

3Set the “TV Speaker option - Off” in the

AUDIO menu. (Źp.150). See the external audio

equipment instruction manual for operation.

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT WIRELESS CONNECTION

(OPTIONAL EXTRAS)

LG TVs with a Wireless Control port support the LG Wireless Media Box, which is sold separately.

When you connect the wireless ready dongle (included with the media box) to the TV, external devices

can be connected to the LG Wireless Media Box and video and audio will be sent to the TV wirelessly.

RGB IN (PC)

LAN

(RGB/DVI)

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT INAV IN 1

AUDIO IN

AUDIO OUT

WIRELESS

CONTROL

OUT

WIRELESS

CONTROL

/DVI IN

L R

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

ꔡ

1. How to connect

1Connect the WIRELESS CONTROL jack of the Wireless Ready Dongle to the WIRELESS

CONTROL jack on the TV.

2Connect HDMI OUT jack of the Wireless Ready Dongle to the HDMI IN jack on the TV.

2. How to use

ᯫ

Select the desired input source on the TV using the INPUT button on the remote control.

ᯫ

Refer to the Wireless Media Box manual for operating instructions.

NOTE

ŹWhen using the external device connected to the Wireless Media Box, some functions of the TV

menu may not work.

EXTERNAL EQUIPMENT SETUP

DVI to HDMI Connection

1. How to connect

1Connect the DVI output of the PC to the HDMI/

DVI IN 1,2,3, or 4* jack on the TV.

2Connect the PC audio output to the AUDIO IN

(RGB/DVI) jack on the TV.

2. How to use

ᯫ

Turn on the PC and the TV.

ᯫ

Select the HDMI1,HDMI2,HDMI3, or HDMI4* input

source on the TV using the INPUT button on the

remote control.

DVI OUTPUT AUDIO

RGB IN (PC)

LAN

WIRELESS

CONTROL

VIDEO

L(MONO)

VIDEO AUD

AUDIO OUT

/DVI IN

(RGB/DVI)

AUDIO IN

OPTICAL DIGITAL

RS-232C

(CONTROL&

ꔡ

* HDMI4: For Plasma TV

LAN

IRELESS

NTROL

/DVI IN

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT INAV IN 1

AUDIO OUT

RGB IN (PC)

RGB OUTPUT

AUDIO

(RGB/DVI)

AUDIO IN

L R

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

ꔡ

PC SETUP

This TV provides Plug and Play capability, meaning that a PC adjusts automatically to the TV's set-

tings.

1. How to connect

1Connect the VGA output of the PC to the

RGB IN (PC)jack on the TV.

2Connect PC audio output to the AUDIO IN

(RGB/DVI) jack on the TV.

2. How to use

ᯫ

Turn on the PC and the TV.

ᯫ

Select the RGB-PC input source on the TV using

the INPUT button on the remote control.

VGA (D-Sub 15 Pin) Connection

EXTERNAL EQUIPMENT SETUP

Supported Display Specifications (RGB-PC, HDMI-PC)

NOTE

ŹTo get the the best picture quality, adjust the PC graphics card to 1920x1080.

ŹDepending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.

ŹIn PC mode, there may be noise associated with the resolution, vertical pattern, contrast or bright-

ness. If noise is present, change the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.

ŹAvoid keeping a fixed image on the screen for a long period of time. The fixed image may become

permanently imprinted on the screen.

ŹThe synchronization input form for Horizontal and Vertical frequencies is separate.

ŹDepending on the graphics card, some resolution settings may not allow the image to be posi-

tioned on the screen properly.

ŹIf you experience overscan issues when using HDMI-PC 1920x1080, change aspect ratio to Just

scan.

ŹWhen selecting HDMI-PC, set the “Input Label - PC” in the OPTION menu.

Resolution Horizontal

Frequency (KHz)Vertical

Frequency (Hz)

640x350 31.468 70.09

720x400 31.469 70.08

640x480 31.469 59.94

800x600 37.879 60.31

1024x768 48.363 60.00

1280x768 47.776 59.87

1360x768

47.712 60.015

1280x1024

63.981 60.02

1920x1080

RGB-PC

66.587 59.934

1920x1080

HDMI-PC

67.50 60.00

EXTERNAL EQUIPMENT SETUP

Screen Setup for PC mode

You can choose the resolution in RGB-PC mode.

The Position, Phase, and Size can also be adjusted.

You can choose this option only when the PC resolution is set to 1024X768, 1280X768 or 1360X768.

Selecting Resolution

ᯡ[

۳[

۳[

$XWR&RQILJ

5HVROXWLRQ

3RVLWLRQ

6L]H

Phase

Reset

6&5((1

ᯒ0RYHᰙ3UHY

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Resolution.

ENTER

Select the desired resolution.

ENTER

3,&785( ᯒ0RYHᯙ(QWHU

ᯐ

ᯙ

  ؒ&RORU 

  ؒ7LQW 

  ؒ&RORU7HPS 

  ؒ$GYDQFHG&RQWURO

  ؒ3LFWXUH5HVHW

ؒ 7UX0RWLRQ

ؒ 6FUHHQ5*%3&

ؒ /('/RFDO'LPPLQJ2Q

EXTERNAL EQUIPMENT SETUP

Automatically adjusts picture position and minimizes image instability. After adjustment, if the image

is still not correct, try using the manual settings or a different resolution or refresh rate on the PC.

Auto Configure

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Auto Config. or

Reset.

ENTER

Select Yes.

ENTER

ᯫ

If the position of the image is still not

correct, try Auto adjustment again.

ᯫ

If picture needs to be adjusted again

after Auto adjustment in RGB-PC,

you can adjust the Position,Size or

Phase.

$XWR&RQILJ

5HVROXWLRQ

3RVLWLRQ

6L]H

Phase

Reset

$XWR&RQILJ

Yes 1R

6&5((1

ᯒ0RYHᰙ3UHY

3,&785( ᯒ0RYHᯙ(QWHU

ᯐ

ᯙ

  ؒ&RORU 

  ؒ7LQW 

  ؒ&RORU7HPS 

  ؒ$GYDQFHG&RQWURO

  ؒ3LFWXUH5HVHW

ؒ 7UX0RWLRQ

ؒ 6FUHHQ5*%3&

ؒ /('/RFDO'LPPLQJ2Q

Returns Position,Size, and Phase to the default initial settings.

This feature operates only in RGB-PC mode.

Screen Reset (Reset to original initial values)

$XWR&RQILJ

3RVLWLRQ

5HVROXWLRQ

6L]H

Phase

Reset

7R6HW

Yes 1R

6&5((1

ᯒ0RYHᰙ3UHY

EXTERNAL EQUIPMENT SETUP

If the picture is not clear after auto adjustment or if text is shaking, adjust the picture phase manually.

This feature operates only in RGB-PC mode.

Adjustment for screen Position, Size, and Phase

Select PICTURE.

ENTER

Select Screen (RGB-PC).

ENTER

Select Position,Size, or Phase.

ENTER

Make appropriate adjustments.

ENTER

ᯫ

Position: This function is to adjust

picture to left/right and up/down as

you prefer.

ᯫ

Size: This function is to minimize any

vertical bars or stripes visible on the

screen background. And the horizon-

tal screen size will also change.

ᯫ

Phase: This function allows you to

remove any horizontal noise and

clear or sharpen the image of char-

acters.

$XWR&RQILJ

5HVROXWLRQ

3RVLWLRQ

6L]H

Phase

Reset

6&5((1

ᯒ0RYHᰙ3UHY

3,&785( ᯒ0RYHᯙ(QWHU

ᯐ

ᯙ

  ؒ&RORU 

  ؒ7LQW 

  ؒ&RORU7HPS 

  ؒ$GYDQFHG&RQWURO

  ؒ3LFWXUH5HVHW

ؒ 7UX0RWLRQ

ؒ 6FUHHQ5*%3&

ؒ /('/RFDO'LPPLQJ2Q

܁۽

EXTERNAL EQUIPMENT SETUP

RGB IN (PC)

WIRELESS

CONTROL

(RGB/DVI)

/DVI IN

VIDEO

AUDIO

L(MONO)

VIDEO AUDIO

COMPONENT INAV IN 1

AUDIO IN

AUDIO OUT

LAN

L R

OPTICAL DIGITAL

RS-232C IN

(CONTROL&

SERVICE)

ꔡ

Broadband modem

Router

Broadband Service

NETWORK SETUP

This TV can be connected to a local area network (LAN) via the LAN port. After making the physical

connection, the TV needs to be set up for network communication.

CAUTION

ŹDo not connect a modular phone cable to the LAN port.

ŹSince there are various connection methods, please follow the specifications of your telecommu-

nication carrier or internet service provider.

1. How to connect

1Connect the LAN port of the Modem or Router to the LAN port on the TV.

2. How to use

ᯫ

Select “Network Setting” in the NETWORK menu.

ᯫ

After connecting the LAN port, use the NETCAST menu.

ᯫ

For more information about NETCAST setup and troubleshooting, visit http://lgknowledgebase.

com. Search for NETCAST.

Wired Network Connection

EXTERNAL EQUIPMENT SETUP

ᯫ

This feature requires an always-on

broadband internet connection.

ᯫ

You do not need to connect to a PC

to use this function.

ᯫ

If Network Setting is not working,

check your network conditions. Check

the LAN cable and make sure your

router has DHCP turned on if you

wish to use the Auto Setting.

ᯫ

If the Network Setting is not com-

pleted, network may not operate nor-

mally.

ᯫ

IP Auto Setting: Select it if there is a

DHCP server on the local area net-

work (LAN) via wired connection, the

TV will automatically be allocated an

IP address. If you are using a router,

it (normally) will have the DHCP

server activated by default.

ᯫ

IP Manual Setting: Select it if there is

no DHCP server on the network and

you want to set the IP address manu-

ally.

1(7:25. ᯒ0RYHᯙ(QWHU

ؒ 1HWZRUN6HWWLQJ :LUHG

ؒ 1HWZRUN6WDWXV ,QWHUQHWLVFRQQHFWHG

ؒ /HJDO1RWLFH

ؒ (61

Wired Network Setup

Select NETWORK.

ENTER

Select Network Setting.

ENTER

Select Wired.

ENTER

If you already set Network Setting:

Select Resetting. The new connection

settings resets the current network

settings.

ENTER

Select IP Auto Setting or IP Manual

Setting.

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

When Selecting IP Manual Setting:

IP addresses will need to be input

manually.

ENTER

Select Enter.

IP Auto Setting

If you already set the

Network Setting

IP Manual Setting

If wired and wireless networks are both available, wired is the preferred method.

After making a physical connection, a small number of home networks may require the TV network

settings to be adjusted.

For detail information, contact your internet provider or router manual.

1HWZRUN7\SH

:LUHGQHWZRUNLVUHFRPPHQGHG

:LUHG

:LUHOHVV

1HWZRUN6HWWLQJ

6HOHFWWKH,3VHWWLQJPRGH

,30RGH ܁,3$XWR6HWWLQJ۽

ᯘ,3$GGUHVV 

ᯘ6XEQHW0DVN 

ᯘ*DWHZD\ 

ᯘ'166HUYHU 

ᰙ3UHYLRXV

(QWHU

᰿([LW

1HWZRUN6HWWLQJ

,QVHUWWKH,3DGGUHVV

,30RGH ܁,30DQXDO6HWWLQJ۽

ᯘ,3$GGUHVV 

ᯘ6XEQHW0DVN 

ᯘ*DWHZD\ 

ᯘ'166HUYHU 

ᰙ3UHYLRXV

(QWHU

᰿([LW

1HWZRUN6WDWXV

1HWZRUNFRQQHFWLQJ

6HWWLQJ 7HVW &ORVH

3UHYLRXVVHWWLQJYDOXHH[LVWV'R

\RXZDQWWRFRQQHFWZLWKWKH

SUHYLRXVVHWWLQJ"

(QWHU

5HVHWWLQJ

᰿([LW

ᯙ1H[W

Appeared when wired and

wireless are simultaneously

connected.

EXTERNAL EQUIPMENT SETUP

NOTE

ŹFor more information about NETCAST setup

and troubleshooting, visit http://lgknowledge-

base.com. Search for NETCAST.

ŹUse a standard LAN cable with this TV. Cat5

or better with a RJ45 connector.

ŹMany network connection problems during set

up can often be fixed by re-setting the router

or modem. After connecting the player to the

home network, quickly power off and/or dis-

connect the power cable of the home network

router or cable modem. Then power on and/or

connect the power cable again.

ŹDepending on the internet service provider

(ISP), the number of devices that can receive

internet service may be limited by the appli-

cable terms of service. For details, contact

your ISP.

ŹLG is not responsible for any malfunction of

the TV and/or the internet connection feature

due to communication errors/malfunctions

associated with your broadband internet con-

nection, or other connected equipment.

ŹLG is not responsible for problems within your

internet connection.

ŹSome content available through the network

connection may not be compatible with the

TV. If you have questions about such content,

please contact the producer of the content.

ŹYou may experience undesired results if the

network connection speed does not meet the

requirements of the content being accessed.

ŹSome internet connection operations may not

be possible due to certain restrictions set by

the Internet service provider (ISP) supplying

your broadband Internet connection.

ŹAny fees charged by an ISP including, without

limitation, connection charges are your respon-

sibility.

ŹA 10 Base-T or 100 Base-TX LAN port is

required for connection to this TV. If your inter-

net service does not allow for such a connec-

tion, you will not be able to connect the TV.

ŹA DSL modem is required to use DSL service

and a cable modem is required to use cable

modem service. Depending on the access

method of and subscriber agreement with

your ISP, you may not be able to use the inter-

net connection feature contained in this TV or

you may be limited to the number of devices

you can connect at the same time. (If your ISP

limits subscription to one device, this TV may

not be allowed to connect when a PC is

already connected.)

ŹThe use of a “Router” may not be allowed or

its usage may be limited depending on the

policies and restrictions of your ISP. For details,

contact your ISP directly.

ŹThe wireless network operates at 2.4 GHz

radio frequencies that are also used by other

household devices such as cordless tele-

phone, Bluetooth® devices, microwave oven,

and can be affected by interference from

them. It can be interrupted by the device

using 5Ghz radio frequencies. It is same

device with LG wireless media box, cordless

telephone, other Wi-Fi device.

ŹIt may decrease the service speed using

Wireless network by surrounding wireless con-

dition.

ŹTurn off all unused network equipment in your

local home network. Some devices may gen-

erate network traffic.

ŹIn some instances, placing the access point or

wireless router higher up away from the floor

may improve the reception.

ŹThe reception quality over wireless depends

on many factors such as type of the access

point, distance between the TV and access

point, and the location of the TV.

ŹWhen connecting internet through the wired/

wireless sharing machine, it may interrupt the

connection because of the use limitation and

confirmation of service company.

ŹTo connect wireless AP, an AP that supports

the wireless connection is necessary, and the

wireless connection function of the AP needs

to be activated. Please enquire to the AP sup-

plier for the possibility of AP wireless connec-

tions.

ŹPlease verify the security settings of AP SSID

for wireless AP connection, and enquire to the

AP supplier for the AP SSID security settings.

ŹThe TV can become slower or malfunction

with wrong settings of network equipments

(wired/wireless router, hub, etc). Please install

correctly by referring to the manual of the

equipment, and set the network.

ŹWhen AP is set to include 802.11 n, and if

Encryption is designated as WEP(64/128bit)

or WPA(TKIP/AES), the connection may not

be possible. There may be different connec-

tion methods according to the AP manufac-

turers.

EXTERNAL EQUIPMENT SETUP

IN 4

AV IN 2

VIDEO

AUDIO

L(MONO)

H/P USB IN 1 USB IN 2

The LG Wireless LAN for Broadband/DLNA Adaptor, which is sold separately, allows the TV to connect

to a wireless lan network.

The network configuration and connection method may vary depending on the equipment in use and

the network environment. Refer to the setup instructions supplied with your access point or wireless

router for detailed connection steps and network settings.

1. How to connect

1Connect the “LG Wireless LAN for Broadband/DLNA Adaptor (LED LCD TV: sold sepa-

rately)” to the USB IN 1 or 2port on the TV.

2. How to use

ᯫ

Select “Network Setting” in the NETWORK menu.

ᯫ

After connecting, you can use the NETCAST menu.

Wireless Network Connection

NOTE

ŹWe recommend you use a wired network connection when available when viewing movies over the

network connection.

ŹWhen the wireless port of the router is used, there may be restrictions for some functions.

EXTERNAL EQUIPMENT SETUP

Setting up the AP (Access Point) or the wireless router is required before connecting the TV to the

network.

Wireless Network Setup

ENTER

Scan the all available AP (Access

Point) or wireless routers within range

and display them as a list.

ENTER

Select an AP (Access Point) or

wireless router on the list.

(If your AP is locked, insert the

security key of AP).

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

ENTER

Input the security key of AP.

Select NETWORK.

ENTER

Select Network Setting.

ENTER

Select Wireless.

ENTER

If you already set Network

Setting: Select Resetting.

The new connection settings

resets the current network set-

tings.

ENTER

Select Setting from the AP list.

1(7:25. ᯒ0RYHᯙ(QWHU

ؒ 1HWZRUN6HWWLQJ :LUHG

ؒ 1HWZRUN6WDWXV ,QWHUQHWLVFRQQHFWHG

ؒ /HJDO1RWLFH

ؒ (61

1HWZRUN7\SH

:LUHGQHWZRUNLVUHFRPPHQGHG

:LUHG

:LUHOHVV

6HOHFWLQJWKHZLUHOHVVQHWZRUNVHWWLQJW\SH

6HOHFWWKHZLUHOHVVQHWZRUNVHWWLQJW\SH

6HWWLQJIURPWKH$3OLVW

6LPSOHVHWWLQJ:36EXWWRQPRGH

6HWWLQJ$GKRFQHWZRUN

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

6HOHFWLQJ$3

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

6HOHFW$3\RXZDQWWRFRQQHFW

PDJH1/1

,QSXWWKHQHZ66,'

LSWLPH

ASW

1HWZRUN

ᯕ&RQQHFWLQJZLWK3,1PRGH

$FFHVV3RLQW

6HDUFK

9Repeat step 4-5 on P.48.

If your AP is locked

If you already set the

Network Setting

3UHYLRXVVHWWLQJYDOXHH[LVWV'R

\RXZDQWWRFRQQHFWZLWKWKH

SUHYLRXVVHWWLQJ"

(QWHU

5HVHWWLQJ

᰿([LW

ᯙ1H[W

,QVHUWLQJWKHVHFXULW\NH\

,QVHUWWKHVHFXULW\NH\RI$3

,QVHUWa$6&,,FKDUDFWHUV

(QWHU &DQFHO

ᰙ3UHY ᰿([LW

܁۽

1HWZRUN6HWWLQJ

6HOHFWWKH,3VHWWLQJPRGH

,30RGH ܁,3$XWR6HWWLQJ۽

ᯘ,3$GGUHVV 

ᯘ6XEQHW0DVN 

ᯘ*DWHZD\ 

ᯘ'166HUYHU 

ᰙ3UHYLRXV

(QWHU

᰿([LW

Appeared when wired and wireless

are simultaneously connected.

EXTERNAL EQUIPMENT SETUP

If you want to connect the AP (Access Point) or router with PIN, use this feature.

Use the simple setting if your access point or wireless router supports a PIN or WPS (Wi-Fi Protected

Setup)

When a security code is already set

PIN (Personal Identification Number)

Simple setting (WPS-button mode)

ᯫ

PIN number is the unique 8 digit number

of the dongle.

&RQQHFWLQJZLWK3,1PRGH

,QVHUW3,1QXPEHUDWWKH$3ZHESDJHDQG

SUHVV؋&RQQHFW،EXWWRQ

3,118%0(5

&RQQHFW

ᰙ3UHYLRXV

)RUPRUHLQIRUPDWLRQFKHFNWKH$3PDQXDO

᰿([LW

ᯙ1H[W

6LPSOHVHWWLQJ:36EXWWRQPRGH

3UHVV3%&0RGHEXWWRQRI$3DQGSUHVV؋&RQQHFW،EXWWRQ

&RQQHFW

ᰙ3UHYLRXV

&DXWLRQ&KHFNLI3%&PRGHEXWWRQLVDYDLODEOHIRU\RXU$3

᰿([LW

ᯙ1H[W

6HOHFWLQJ$3

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

6HOHFW$3\RXZDQWWRFRQQHFW

PDJH1/1

,QSXWWKHQHZ66,'

LSWLPH

ASW

1HWZRUN

ᯕ&RQQHFWLQJZLWK3,1PRGH

$FFHVV3RLQW

6HDUFK

2Connect the acccess point with PIN

mode.

ENTER

Select Connect.

RED

1Repeat step 1-6 on P.51.

3You can see the Network ID and Security Key

on your TV screen.

Enter the PIN number to your device.

6HOHFWWKHZLUHOHVVQHWZRUNVHWWLQJW\SH

6HWWLQJIURPWKH$3OLVW

6LPSOHVHWWLQJ:36EXWWRQPRGH

6HWWLQJ$GKRFQHWZRUN

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

1Repeat step 1-4 on P.51. 3

ENTER

Select Connect.

ENTER

Select Simple setting (WPS-

button mode).

5Repeat step 4-5 on P.48.

4Repeat step 4-5 on P.48.

EXTERNAL EQUIPMENT SETUP

The below settings are only for connecting directly to a PC.

This is the same as connecting two PCs with a cross-over cable.

AD-hoc Mode

1Repeat step 1-3 on P.51.

6HOHFWLQJWKHZLUHOHVVQHWZRUNVHWWLQJW\SH

6HOHFWWKHZLUHOHVVQHWZRUNVHWWLQJW\SH

6HWWLQJIURPWKH$3OLVW

6LPSOHVHWWLQJ:36EXWWRQPRGH

6HWWLQJ$GKRFQHWZRUN

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

6HWWLQJ$GKRFQHWZRUN

)HDWXUHVXVLQJH[LWLQJQHWZRUNFDQEHXQDYDLODEOH'R\RX

ZDQWWRFKDQJHQHWZRUNFRQQHFWLRQ"

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

(QWHU &DQFHO

6HWWLQJ$GKRFQHWZRUN

,QVHUWWKHVHWWLQJLQIRUPDWLRQLQWRWKHGHYLFH

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

1HWZRUN,'66,'/*79

6HFXULW\.H\

ᯕ&KDQJLQJWKHVHWWLQJLQIRUPDWLRQ

&RQQHFW

ENTER

Select Setting AD-hoc net-

work.

ENTER

Select Enter.

ENTER

Select Connect to connect Ad-hoc

network.

You can see the Network ID and

Security Key on your TV screen.

Enter this Network ID and Security

Key to your device.

If a network may not operate,

change the setting information

using the RED button.

ENTER

Insert the IP address.

ENTER

Network setting is completed.

Select Close.

1HWZRUN6HWWLQJ

,QVHUWWKH,3DGGUHVV

,30RGH ,30DQXDO6HWWLQJ

ᯘ,3$GGUHVV 

ᯘ6XEQHW0DVN 

ᯘ*DWHZD\ 

ᯘ'166HUYHU 

ᰙ3UHYLRXV

(QWHU

᰿([LW

1HWZRUN6WDWXV

$GKRFQHWZRUNLVFRQQHFWHG

/*79

0DF$GGUHVV

,3$GGUHVV 

6XEQHW0DVN

*DWHZD\ 

6HWWLQJ 7HVW &ORVH

6LJQDO6WUHQJWK

*DWHZD\

6HWWLQJ$GKRFQHWZRUN

,QVHUWWKHVHWWLQJLQIRUPDWLRQLQWRWKHGHYLFH

1HWZRUN,'66,'/*79

6HFXULW\.H\

&DQFHO

&RQQHFWLQJWKH$GKRFQHWZRUN

ᯫ

PC Setting

Internet Protocol(TCP/IP) of PC needs to be set

manually.

IP address, Subnet Mask, and default Gateway

can be set with your own discretion.

i.e) IP address: 192.168.0.1 / Subnet Mask:

255.255.255.0 / default Gateway: 192.168.0.10

ᯫ

TV Setting

Verify IP address and gateway of PC.

Input Gateway address of PC to IP Address, and

IP Address of PC to Gateway, and select Enter.

i.e) IP address: 192.168.0.10 / Subnet Mask:

255.255.255.0 / default Gateway: 192.168.0.1

ᯫ

Example of the PC setting that

supports a wireless network

1. Find a wireless network device in

your PC.

2. Select LGTV10 that appears in

the list. (Select the same name

as the network ID that appears

on your TV screen.)

3. Type 1111111111 in the Inserting

the security key dialog.

(Type the security key that

appears on your TV screen.)

EXTERNAL EQUIPMENT SETUP

Select NETWORK.

ENTER

Select Network Status.

ENTER

Check the newtwork status.

Network Status

ᯫ

Setting: Return to the network set-

ting menu or wireless network setting

type menu.

ᯫ

Test: Test the current network status

after setting the network.

ᯫ

Close: Return to the previous menu.

1(7:25. ᯒ0RYHᯙ(QWHU

ؒ 1HWZRUN6HWWLQJ :LUHG

ؒ 1HWZRUN6WDWXV ,QWHUQHWLVFRQQHFWHG

ؒ /HJDO1RWLFH

ؒ (61

6HOHFWWKHZLUHOHVVQHWZRUNVHWWLQJW\SH

6HWWLQJIURPWKH$3OLVW

6LPSOHVHWWLQJ:36EXWWRQPRGH

6HWWLQJ$GKRFQHWZRUN

ᰙ3UHYLRXV ᰿([LW

ᯙ1H[W

Wired Connection

Wireless Connection

1HWZRUN6HWWLQJ

6HOHFWWKH,3VHWWLQJPRGH

,30RGH ܁,3$XWR6HWWLQJ۽

ᯘ,3$GGUHVV 

ᯘ6XEQHW0DVN 

ᯘ*DWHZD\ 

ᯘ'166HUYHU 

ᰙ3UHYLRXV

(QWHU

᰿([LW

1HWZRUN6WDWXV

1HWZRUNFRQQHFWLQJ

6HWWLQJ 7HVW &ORVH

WATCHING TV / CHANNEL CONTROL

REMOTE CONTROL FUNCTIONS

When using the remote control, aim it at the remote control sensor on the TV.

The remote control may differ from the images below.

WATCHING TV / CHANNEL CONTROL

ENERGY

CHVOL

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

SAVING

AV MODE

INPUT

LIGHT

FAV

RATIO

MUTE

BACK

WIDGETS

EXIT

ENTER

MARK

DELETE

CHAR/NUM

LIST

FLASHBK

Q.MENU

ENERGY

CHVOL

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

SAVING

AV MODE

INPUT

LIGHT

FAV

MUTE

BACK

WIDGETS

EXIT

ENTER

MARK

DELETE

CHAR/NUM

LIST

FLASHBK

Q.MENU

POWER Turns the TV on from standby or off to

standby.

LIGHT Illuminates the remote control buttons.

ENERGY SAVING

Adjusts the Energy Saving setting.

Źp.132

AV MODE Toggles through preset Video and

Audio modes. Źp.85

INPUT Rotates through inputs.

Also switches the TV on from standby.

TV Returns to the last TV channel.

NUMBER button

— (DASH) Used to enter a program number for

multiple program channels such as 2-1,

2-2, etc.

LIST Displays the channel table.

FLASHBK Tunes to the last channel viewed.

VOLUME UP/

DOWN Adjusts the volume.

FAV Set up desired favorite channels list.

MARK Select the input to apply the Picture

Wizard settings. Źp.131

Use to mark or unmark a photo/music/

movie. Źp.105, 110, 116

RATIO Changes the aspect ratio. Źp.128

3D Used for viewing 3D video. Źp.94

CHAR/NUM Shifts the Character or Number in

internet settings.

MUTE Switches the sound on or off.

DELETE Delete the character or number on the

screen.

CHANNEL

UP/DOWN

Changes the channel.

PAGE

UP/DOWN

Moves from one full set of screen infor-

mation to the next one.

WATCHING TV / CHANNEL CONTROL

MUTE

BACK

WIDGETS

EXIT

ENTER

DELETE

L/R SELECT

Q.MENU

MUTE

BACK

WIDGETS

EXIT

ENTER

FREEZE

Q.MENU

MUTE

BACK EXIT

ENTER

Q.MENU

INFO

FREEZE

MUTE

BACK EXIT

ENTER

L/R SELECT

Q.MENU

INFO

MENU Displays the main menu or clears all

on-screen displays and return to TV

viewing.

NETCAST

Select the desired NETCAST menu

source.

Źp.123

Q.MENU Opens the list of Quick Menu options.

Źp.66

THUMBSTICK

(Up/Down/Left

Right/ENTER)

Navigates the on-screen menus and

adjusts the system settings to your

preference.

BACK Allows the user to move return one step

in an interactive application or other

user interaction function.

WIDGETS WIDGETS for showing or hiding the

Yahoo! Dock and accessing the Yahoo!

TV Widgets user experience.

INFO Displays channel information at the

bottom of the screen. Źp.78

EXIT Clears all on-screen displays and return

to TV viewing.

COLOR

BUTTON

Access special functions in some

menus.

L/R SELECT Used for viewing 3D video. Źp.95

WATCHING TV / CHANNEL CONTROL

ᯫ

Open the battery compartment cover on the back side and install

the batteries matching correct polarity.

ᯫ

Install two 1.5V AAA batteries. Don’t mix old or used batteries

with new ones.

ᯫ

Close cover.

Installing Batteries

FREEZE

INFO

L/R SELECT

INFO RATIO

FREEZE

L/R SELECT

RATIO

USB,

SIMPLINK

Control buttons

ţControls MY MEDIA menu (Movie List,

Photo List, Music List)

ţControls the SIMPLINK compatible

devices.

FREEZE

(For Plasma TV)

Pause the present picture at the screen.

(It doesn’t work at USB Mode and

Simplink.)

The TV returns to normal viewing auto-

matically if no signal is received or no

operation is performed for 5 minutes.

If you keep the screen in Freeze condi-

tion, the residual image can exist.

SIMPLINK See a list of AV devices connected to

TV.

When you toggle this button, the

SIMPLINK menu appears at the screen.

Źp.90

RATIO Changes the aspect ratio. Źp.128

WATCHING TV / CHANNEL CONTROL

The Magic Motion Remote Control communicates with your TV by using a 2.4 GHz bandwidth radio

frequency (RF).

ᯫ

Output: 1 dBm or lower

ᯫ

Maximum Communication Distance: 10 m (30 ft) in an open space

ᯫ

Bandwidth: 2.4 GHz (2.4035 GHz - 2.4783 GHz)

ᯫ

Transfer Rate: 250 kbps

ᯫ

When the message "Magic motion

remote control battery is low. Change

the battery." is displayed, replace the

battery.

ᯫ

Open the battery compartment

cover on the back side and install the

batteries matching correct polarity.

ᯫ

Install two 1.5V AA batteries. Don’t

mix old or used batteries with new

ones.

ᯫ

Close cover.

Installing Batteries

RF Specification of the Magic Motion Remote Control

ENTER

VOL

MUTE

MAGIC MOTION REMOTE CONTROL FUNCTIONS

Pointer Receiver Blinks the light when operating.

POWER Turns the TV on from standby or off to standby.

ENTER/HOME

Menu Button

Activates the pointer.

VOLUME UP/

DOWN Adjusts the volume.

CHANNEL

UP/DOWN

Changes the channel.

MUTE Switches the sound on or off.

WATCHING TV / CHANNEL CONTROL

Magic Motion Remote Control Registration

How to use Magic Motion Remote Control

Precautions to Take when Using the Magic Motion Remote Control

The Magic Motion Remote Control operates by pairing with your TV.

ENTER

How to register the Magic Motion Remote Control

To register the Remote Control, press the ENTER button on the

Remote Control while aiming it at your TV.

MUTE

How to Re-register the Magic Motion Remote Control after

Registration Failure

Reset the remote control by pressing and holding both the

ENTER and MUTE buttons for 5 seconds. (Once the reset is

complete, the light on the Pointer RF Receiver blinks.) Then

repeat the above procedure to register the remote control.

ENTER

Press this button if there is no pointer on your TV screen. The pointer will then appear on the

screen.

If the pointer has not been used for a certain period of time, it will disappear.

2You can move the pointer by aiming the Pointer Receiver of the remote

control at your TV then move it left, right, up or down.

If the pointer does not work properly after clicking the ENTER button, leave

the remote control for 10 seconds then use it again.

ᯫ

Use the remote control within the maximum commu-

nication distance (10 m). Using the remote control

beyond this distance, or with an object obstructing it,

may cause a communication failure.

ᯫ

A communication failure may occur due to nearby

devices. Electrical devices such as a microwave oven or

wireless LAN product may cause interference, as this

will use the same bandwidth (2.4 GHz) as the Magic

Motion Remote Control.

ᯫ

The Magic Motion Remote Control may be damaged

or may malfunction if it is dropped or receives a heavy

impact.

ᯫ

When playing a game using the Magic Motion Remote

Control, hold it securely by wrapping its strap around

your wrist and adjusting the length with the adjustable

ring.

ᯫ

Take care not to bump into nearby furniture or other

people when using the Magic Motion Remote Control.

ᯫ

Manufacturer and installer cannot provide service

related to human safety as the applicable wireless

device has possibility of electric wave interference.

WATCHING TV / CHANNEL CONTROL

Pointer Menu Options

ENTER

Select Home Menu.

ENTER

Select Pointer.

ENTER

Make appropriate adjustments.

ENTER

Select Exit.

+RPH0HQX

4XLFN0HQX

&KDQQHO/LVW

1HWFDVW

6FUHHQ5HPRWH

6,03/,1. 1(7&$67 0<0(',$ 48,&.0(18

,1387 *$0(6&+('8/(

Today

6LPSOH0DQXDO 3RLQWHU ([LW

ؒ6SHHG ܁1RUPDO ۽

ؒ6KDSH ܁7\SH$ ۽

ؒ6L]H ܁0HGLXP ۽

ؒ$OLJQPHQW ܁2Q ۽

ᰙ([LW

ᯫ

Speed: Changed the pointer speed.

ᯫ

Shape: Select the pointer shape.

ᯫ

Size: Changes the pointer size.

ᯫ

Alignment: When Alignment is On,

you can easily align the remote con-

trol's direction with the pointer on

your TV screen by shaking the remote

control left and right. Then, the point-

er automatically moves to the center

of the screen.

LG Electronics USA 50PX950UA Plasma monitor User Manual 50PX950 U 1

LG Electronics USA Plasma monitor 50PX950 U 1

Contents

User manual 1 of 2

Navigation menu

Namespaces

Views

Navigation