LG Electronics USA 52SZ8DUA 52" DLP PROJECTION TV User Manual User s Manual H

LG Electronics USA 52" DLP PROJECTION TV User s Manual H

UserManual.wiki >

LG Electronics USA >

52SZ8DUA User Manual HTML Version

USERS MANUAL

EUT Type: 52” DLP Projection TV

FCC ID: BEJ52SZ8DUA

Test Report No.: GETEC-E3-05-037

FCC Class B Certification

APPENDIX H

: USER’S MANUAL

Installation and Operating Guide |Warranty

Model Numbers |Z44SZ80/Z52SZ80 |DLP PROJECTION

2 DLP Projection TV

WARNING/CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-

cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appli-

ance.

WARNING/CAUTION:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY

INSERT.

ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE

DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National

Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that

the cable ground shall be connected to the grounding system of the building, as close to the point of the

cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized mod-

ification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is:

Zenith Electronics Corporation

1-201-816-2000

Marked and Distributed in the United States by LG Electronics U.S.A., Inc.

1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

http://www.zenith.com

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

/CAUTION

Warning/Caution

arning/Caution

Warning/Caution

Owner’s Manual 3

Safety Instructions

IMPORTANT SAFETY INSTRUCTIONS

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or

sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the appara-

tus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The

important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be includ-

ed where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding

statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illus-

trates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction :

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-

fiers)that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the

third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Safety Instructions

PORTABLE CART WARNING

4 DLP Projection TV

Safety Instructions

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged

in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into

the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped.

15. CAUTION concerning the Power Cord :

Most appliances recommend they be placed upon a dedicated circuit; that

is, a single outlet circuit which powers only that appliance and has no

additional outlets or branch circuits. Check the specification page of

this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged

wall outlets, extension cords, frayed power cords, or damaged or

cracked wire insulation are dangerous. Any of these conditions could

result in electric shock or fire. Periodically examine the cord of your

appliance, and if its appearance indicates damage or deterioration,

unplug it, discontinue use of the appliance, and have the cord replaced

with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being

twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the

cord exits the appliance.

16. Outdoor Use Marking :

WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture.

17. Wet Location :

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall

be placed on the apparatus.

Owner’s Manual 5

Contents

After reading this manual, keep it handy for future reference.

Warnings/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Digital Cable Compatibility . . . . . . . . . . . . . . . . . . . . . . . . .3

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4~5

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Connection Options . . . . . . . . . . . . . . . . . . . .8~9

Remote Control Key Functions . . . . . . . . . .10~11

Installation

External Equipment Connections . . . . . . . . . .12~30

Antenna or Cable Connection . . . . . . . . . . . . . .12

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .13

External A/V Source Setup . . . . . . . . . . . . . . . .14

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

CableCARDTM Setup . . . . . . . . . . . . . . . . . . . . .15

HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . . .15

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . .15

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Digital Audio Output . . . . . . . . . . . . . . . . . . . . .17

External Stereo . . . . . . . . . . . . . . . . . . . . . . . . .17

HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18~20

TV Guide On Screen Setup . . . . . . . . . . . . . .21~30

IEEE 1394 Functions . . . . . . . . . . . . . . . . . . . . . .31-37

TV Guide On ScreenTM System . . . . . . . . . . . . . .38-56

Operation

Turning the TV On . . . . . . . . . . . . . . . . . . . . . .57

TV Setup

On-screen Menus Language Selection . . . . . . .58

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .59

Manual Scan . . . . . . . . . . . . . . . . . . . . . . . . . .59

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .60

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .60

Channel Label Setup . . . . . . . . . . . . . . . . . . . .61

Main Picture Source Selection . . . . . . . . . . . . .61

Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Manual Picture Control (Custom Option) . . . . . .62

Color Temperature Control . . . . . . . . . . . . . . . .62

Video Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .63

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .63

Manual Sound Control (Custom Option) . . . . . .63

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .64

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .64

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . . .64

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .65

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .65

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .65

Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .66

Option Menu Options

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .67

Cinema 3:2 Mode Setup . . . . . . . . . . . . . . . . . .67

Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Caption / Text . . . . . . . . . . . . . . . . . . . . . . . . . .68

Caption Option . . . . . . . . . . . . . . . . . . . . . . . . .69

EZ Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Lock Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .71

CableCARDTM Function

Cable menu options . . . . . . . . . . . . . . . . . . . . .72

Scrambled channel . . . . . . . . . . . . . . . . . . . . . .72

Cable Channel List . . . . . . . . . . . . . . . . . . . . . .73

Emergency Alert Message . . . . . . . . . . . . . . . .73

Notes on Memory Card . . . . . . . . . . . . . . . .74~77

JEPG File Viewing Options . . . . . . . . . . . . .78~82

MP3 File Playing Operation . . . . . . . . . . . . .83~86

Remote Control

PIP (Picture-in-Picture)/POP/Twin Picture . . . ..87

Watching PIP/POP/Twin Picture . . . . . . . . . . . ..87

Selecting an Input Signal Source for PIP/Twin Picture

. .87

Swapping the PIP/Twin Picture . . . . . . . . . . . . .87

TV Program Selection for PIP . . . . . . . . . . . . . .87

Moving the PIP sub picture . . . . . . . . . . . . . . . .88

Adjusting Main and Sub Picture Sizes for Twin Picture . .88

POP (Picture-out-of-Picture: Channel Scan) . . .88

APM(Adaptive Picture Mode) . . . . . . . . . . . . . .89

Brief Info.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90

EZ Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Freeze & Magnify . . . . . . . . . . . . . . . . . . . . . . .91

Screen Setup for PC mode . . . . . . . . . . . . . . . .92

Programming the Remote . . . . . . . . . . . . . . . . . . . . . .93

Programming Codes . . . . . . . . . . . . . . . . . . . . . . .94~95

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . .96~98

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . .100

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103~104

Contents

ENTER

VOL CH

POWER

(북미)

ENTER

VOL CH

POWER

(북미)

확인

방

송

안

내

메

뉴

조용히

이전채널

선호채널

취

소

예

약

목

록

녹

화

목

록

음량 채널

동시화면

취침예약 화면크기 화면조정 주/부전환

음성다중 자막방송

영상파레트

부채널 부채널 부화면입력

방

송

보

기

입력

외부입력

전원

제품선택

페이지

선

택

TN-60/50PY20

TN-42PX40X(한국) DN-42PX40X(한국)

확인

방

송

안

내

메

뉴

화

면

크

기

조용히

이전채널

선호채널

취

소

영

상

파

레

트

음량 채널

동시화면

화면조정

음성다중

자막방송 자동음성 주/부전환

부채널 부채널 부화면입력

입력

외부입력

전원

제품선택

페이지

취

침

예

약

자동음성

6 DLP Projection TV

Introduction

POWER

MENU ENTER VOL CH

- Lamp indicator, operation indicator, and temperature indicator located below the front panel controls, reveal the

operating status of the DLP projection TV.

Function Status Indicators

Controls

Front Panel Controls

Off Power cord is not connected.

Red Power Cord is connected, TV is in standby mode.

Green TV turns on.

Orange (flashing) Preparing operation in standby mode.

Orange Projection lamp is reaching the end of its life and needs to

be replaced with a new lamp. Contact your service center.

Red (flashing) There is a problem with the lamp or around it. Contact an

authorized service center.

Green (flashing) The lamp cover is not closed.

Orange The projection TV is overheating. Check the blocked vents of

the projection TV and the accumulated dust in the dust filter.

Red The projection TV shut down due to overheating.

Red (flashing) The projection TV shut down, check the cooling fan. Contact

your service center.

Operation Indicator

Lamp Indicator

Temperature Indicator

- This is a simplified representation of a front panel.

- Here shown may be somewhat different from your TV.

POWER Button

MENU Button

ENTER Button

VOLUME (F,G)

Buttons CHANNEL (E, D)

Buttons

Operation Indicator/

Lamp Indicator/

Temperature Indicator

Owner’s Manual 7

Introduction

PC/DTV

(XGA

/480p

/720p

/1080i)

S-VIDEO

MONO

RGB INPUT

COMPONENT

INPUT2 INPUT1

DTV/DVD INPUT

RGB/DVI INPUT

(L)

(R)

AUDIO (L)

(R)

AUDIO

VIDEO

(L)

(R)

AUDIO

(L)

(R)

AUDIO

MONITOR

OUT INPUT2 INPUT1

DIGITAL AUDIO

OPTICAL INPUT1

(COMPONENT2)

DIGITAL AUDIO

OPTICAL INPUT2

(DVI)

DIGITAL AUDIO

OPTICAL OUTPUT

ANTENNA

HDMI1

/DVI

VARIABLE

AUDIO OUT

HDMI2

UPGRADE

PORT

CABLE

ANTENNA Inputs

Connect antenna sig-

nals to the TV directly.

DIGITAL AUDIO OPTICAL

OUTPUT

Used to connect either an external

amplifier, or add a sub-woofer to

your surround sound system if it has

a digital

audio optical input.

(Refer to )

MONITOR OUT

Connect a second TV or

Monitor.

S-VIDEO In

A connection avail-

able with some high-

end equipment that

provides even better

picture quality for

Video 2.

RGB/DVI INPUT

Connect the monitor

output connector from

a PC to the appropri-

ate input port.

RGB Input

Connect the TV output

connector from a

PC/DTV to the appro-

priate input port.

VARIABLE AUDIO OUT

Used to connect either an

external amplifier, or add a

sub-woofer to your surround

sound system.

COMPONENT INPUT 1-2

Connect a component

video/audio device to

these jacks. Refer to your

DVD manual for further

information.

VIDEO 1 or 2

Connects the video

signals from various

types of equipment.

Left/Right AUDIO

Used for stereo sound

from various types of

equipment.

CABLE Inputs

Connect cable signals to

the TV, either directly or

through your cable box.

DIGITAL AUDIO OPTI-

CAL INPUT1(COMPO-

NENT2)

Connect digital audio

from the equipment

connected to COMPO-

NENT 2.

DIGITAL AUDIO OPTI-

CAL INPUT2(DVI)

Connect digital audio

from the equipment

connected to

HDMI/DVI(VIDEO).

(Refer to )

Notes: In standby mode, these port will not work.

If the video is connected through HDMI-TO-HDMI cable, you don’t need to connect digital audio. This port

is used only when the video connected through DVI-TO-HDMI cable.

HDMI1/DVI, HDMI 2

Connect a HDMI signal

to HDMI1/DVI or

HDMI2. Or connect a

DVI(Video) signal to

HDMI1/DVI.

Back Connection Panel

Connection Options

8 DLP Projection TV

Introduction

LEFT/RIGHT

AUDIO

Used for stereo

sound from vari-

ous types of

equipment.

S-VIDEO

A connection

available on

some very high-

end equipment

that provides bet-

ter picture quality

than video input.

VIDEO

Connects the

video signals

from any piece of

equipment.

Side A/V Panel

S-VIDEO

VIDEO

SIDE VIDEO

AUDIO

(R)

(L)/

MONO

There are four jacks on the left side on your projection TV

that make connecting Audio/Video devices like video

games and camcorders very simple.

The jacks are like those found on the back jack connection

panel. This means that most equipment that connects to

those types of jacks on the rear jackpack, may be connect-

ed to the front connection panel.

To use the side jacks as the signal source, select them

using Main Input menu as described on page 61. They will

be named “Front Video” in the Main Input menu.

If you input both Front Video and

S-Video, only the S-Video will

work.

If you’re connecting a video game

device, make sure to change the

picture settings with the EZ

Picture option in the Video menu

(see page 62).

Mini glossary

A/V CABLESAudio/Video cables. Three cable connector—Right audio (red), Left audio (white), and Video (yellow). A/V cables are

used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices.

A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).

Front Connection Panel

Owner’s Manual 9

Introduction

123

456

789

MODE LIGHT POWER

TV/VIDEO INFO

SLEEP

VCR

CABLE

DVD SAT

MUTE

SWAPPIPCH- PIPCH+

PIP

RATIO

RECORD

STOP

PAUSE

REW

PLAY

MENU EXIT

CC FREEZE

PIP INPUT

VOL CH

FAV

SAP ADJUST

EZ SoundEZ Video

TV INPUT

SKIP

FLASHBK

- When using the remote control, aim it at the remote control sensor on the TV.

Remote Control Key Functions

INDICATOR LIGHTS

Show active remote mode

every time any button is

pressed.

MODE

Selects the remote operating mode:

TV, VCR, Cable, DVD and Satellite.

Select other operating modes, for the

remote to control external devices.

LIGHT

Illuminates the remote con-

trol keys.

TV/VIDEO

Selects: Analog, Video1, Video2, Side

video, Component1-2, RGB, and DVI

input sources.

FAV

Scrolls the Favorite channels.

INFO

When you watch the TV, information dis-

plays on top of the screen. Not available

in Component 1-2, RGB, HDMI1/DVI and

HDMI2 mode.(Refer to p.90)

MUTE

Switches the sound on or off.

(Refer to

p.91)

ADJUST

Adjusts screen position, size, and phase

in PC mode.

VOLUME UP/DOWN

Increases/decreases the sound level.

NUMBER KEYPAD

For direct channel selection and

programming functions.

RATIO

Changes the screen format or aspect

ratio.

PIP INPUT

Selects the input source for the sub

picture.

ENTER

When in the menu system and other

on-screen displays, selects highlighted

options.

Brings up the main menu to the

screen.

EXIT

Clears all on-screen displays and returns

to TV viewing from any menu.

SKIP

Playing CDs: Selects songs.

Playing DVDs: Selects movie chapters.

10 DLP Projection TV

Introduction

• Open the battery compartment cover on the back side and install the batteries

matching correct polarity (+ with +, - with -).

• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.

Close cover.

Installing Batteries

123

456

789

MODE LIGHT POWER

TV/VIDEO INFO

SLEEP

VCR

CABLE

DVD SAT

MUTE

SWAPPIPCH- PIPCH+

PIP

RATIO

RECORD

STOP

PAUSE

REW

PLAY

MENU EXIT

CC FREEZE

PIP INPUT

VOL CH

FAV

SAP ADJUST

EZ SoundEZ Video

TV INPUT

SKIP

FLASHBK

back of

remote

TV INPUT

• Rotates the input mode between Antenna

and Cable.

• Video 1-2, Front Video, Component 1-2,

RGB-DTV (or RGB-PC), HDMI1/DVI,

HDMI2

and IEEE1394 input sources, TV will return

to the last TV channel.

Selects a closed caption mode for dis-

playing captioning information if avail-

able on program.

POWER

Turns your TV or any other programmed

equipment on or off, depending on mode.

EZ Sound

Selects the sound appropriate for

the program's character.

EZ Video

Adjusts the factory preset picture

depending on the viewing environ-

ment.

Remote Control Key Functions

SLEEP

SAP

Selects MTS sound: Mono, Stereo, and

SAP in Analog mode. Change the audio

language in DTV mode.

CHANNEL UP/DOWN

Scrolls through available channels in

EZ Scan memory.

FLASHBK

Tunes to the last channel viewed.

PIPCH+

Changes to next higher PIP channel.

SWAP

Switches the picture from PIP, POP, or

twin picture to the main screen.

PIPCH-

Changes to next lower PIP channel

PIP

Toggles between PIP, POP (Picture-out-

of-Picture) and Twin picture mode.

FREEZE

Captures and freezes the currently-

viewed main picture in PIP mode.

THUMBSTICK

Allows you to navigate the on-screen

menus and to adjust the system settings

and preferences, by moving to an option

with

F G

and selecting the highlighted

option with .

RECORD, PAUSE, REW, FFWD,

PLAY, STOP

Control the functions on your VCR.

Owner’s Manual 11

Installation

- Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed.

Antenna or Cable Connection

1. Analog and Digital TV signals provided on antenna

2. Analog and Digital TV signals provided on cable

ANTENNA

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

Wall Antenna

Socket

VHF Antenna

UHF Antenna

RF Coaxial Wire (75 ohm)

Bronze Wire

Turn clockwise to tighten.

Bronze Wire

Be careful not to bend the bronze wire when

connecting the antenna.

Bronze Wire

Cable TV Wall

Jack RF Coaxial Wire (75 ohm)

CABLE

Installation

External Equipment Connections

Turn clockwise to tighten.

Owner’s Manual 12

Note: The TV will let you know when the TV(analog antenna), DTV(digital antenna), CATV(analog cable) and CADTV(digital

cable) channel scans are complete.

•To improve the picture quality in a poor signal area,

please purchase a signal amplifier and install properly.

•If the antenna needs to be split for two TV’s, install a “2-

Way Signal Splitter” in the connections.

•If the antenna is not installed properly, contact your deal-

er for assistance.

ANTENNA

Signal

Amplifier

3. Analog and Digital TV signals provided on cable and antenna

Antenna

RF Coaxial Wire (75 ohm)

Bronze Wire

Turn clockwise to tighten.

Cable TV Wall

Jack RF Coaxial Wire (75 ohm)

ANTENNA

CABLE

Connection Option 1

Set VCR output switch to channel 3 or 4 and then tune the

TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the VCR's output

jacks to the TV input jacks, as shown in the figure.

When connecting the TV to VCR, match the jack colors

(Video = yellow, Audio Left = white, and Audio Right = red).

If you connect an S-VIDEO output from VCR to the S-VIDEO

input, the picture quality is improved; compared to connecting

only the Video input.

2. Insert a video tape into the VCR and press PLAY on the

VCR. (Refer to the VCR owner’s manual.)

3. Select the input source with using the TV/VIDEO button on

the remote control. Note that this TV finds the connected

input sources automatically for Video, Front Video and

Component 1-2. It is presumed that RGB, HDMI1/DVI and

HDMI2 sources are connected.

Do not connect to both Video and S-Video at the

same time. In the event that you connect both Video

and the S-Video cables, only the S-Video will work.)

VCR Setup

PC/DTV

(XGA

/480p

/720p

/1080i)

S-VIDEO

MONO

RGB INPUT

COMPONENT

INPUT2 INPUT1

DTV/DVD INPUT

RGB/DVI INPUT

(L)

(R)

AUDIO (L)

(R)

AUDIO

VIDEO

(L)

(R)

AUDIO

(L)

(R)

AUDIO

MONITOR

OUT INPUT2 INPUT1

DIGITAL AUDIO

OPTICAL INPUT1

(COMPONENT2)

DIGITAL AUDIO

OPTICAL INPUT2

(DVI)

DIGITAL AUDIO

OPTICAL OUTPUT

ANTENNA

HDMI1

/DVI

VARIABLE

AUDIO OUT

HDMI2

UPGRADE

PORT

CABLE

S-VIDEO OUT

(R) AUDIO (L)VIDEO

OUTPUT

SWITCH

ANT OUT

ANT IN

VCR Rear

Bronze Wire

Installation

Owner’s Manual 13

Installation

•Component Input ports

To get better picture quality, connect a DVD player to the

component input ports as shown below.

Component ports

on the TV Y PBPR

Video output ports

on DVD player

B-Y

R-Y

How to connect

1. Connect the DVD video outputs (Y, PB, PR) to the COMPO-

NENT (Y, PB, PR) INPUT jacks on the TV and connect the

DVD audio outputs to the AUDIO INPUT jacks on the TV, as

shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to

the S-VIDEO input on the TV and connect the DVD audio out-

puts to the AUDIO INPUT jacks on the TV, as shown in the fig-

ure.

Note: If your DVD player does not have component video output,

use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the TV/VIDEO button on the remote control to select

Component 1 or Component 2. (If connected to S-VIDEO,

select the Video or Front Video external input source.)

3. Refer to the DVD player's manual for operating instructions.

DVD Setup

PC/DTV

(XGA

/480p

/720p

/1080i)

S-VIDEO

MONO

RGB INPUT

COMPONENT

INPUT2 INPUT1

DTV/DVD INPUT

RGB/DVI INPUT

(L)

(R)

AUDIO (L)

(R)

AUDIO

VIDEO

(L)

(R)

AUDIO

(L)

(R)

AUDIO

MONITOR

OUT INPUT2 INPUT1

DIGITAL AUDIO

OPTICAL INPUT1

(COMPONENT2)

DIGITAL AUDIO

OPTICAL INPUT2

(DVI)

DIGITAL AUDIO

OPTICAL OUTPUT

ANTENNA

HDMI1

/DVI

VARIABLE

AUDIO OUT

HDMI2

UPGRADE

PORT

CABLE

(R) AUDIO (L)

S-VIDEO

(R) AUDIO (L) DIGITAL AUDIO

OPTICAL

DVD

Notes:

• Digital Audio will not work for Component 1 input source.

• Digital Audio operation has priority if Digital Audio and AUDIO L/R

are connected at the same time.

How to connect

Connect the audio and video cables from the external equip-

ment's output jacks to the TV input jacks, as shown in the

figure.

When connecting the TV to external equipment, match the

jack colors (Video = yellow, Audio Left = white, and Audio

Right = red).

How to use

1. Select the input source by using the TV/VIDEO button on

the remote control. Note that this TV finds the connected

input sources automatically for Video 1-2 and Component 1-

2. It is presumed that RGB, HDMI1/DVI and HDMI2 sources

are connected.

2. Operate the corresponding external equipment. For connec-

tion instructions for operating the TV Guide On Screen sys-

tem, see page 21~22.

External

External A/V Source Setup

A/V Source Setup

PC/DTV

(XGA

/480p

/720p

/1080i)

S-VIDEO

MONO

RGB INPUT

RGB/DVI INPUT

(L)

(R)

AUDIO (L)

(R)

AUDIO

VIDEO

(L)

(R)

AUDIO

MONITOR

OUT INPUT2 INPUT1

VARIABLE

AUDIO OUT

(L)

(R)

VIDEO

AUDIO VIDEO

Camcorder

Video Game

Set

14 DLP Projection TV

Installation

The TV has a special signal output capability which allows you to

hook up a second TV or monitor.

Connect the second TV or monitor to the TV’s MONITOR OUTPUT.

See the Operating Manual of the second TV or monitor for further

details regarding that device’s input settings.

Note

• Component, RGB-PC/RGB-DTV, HDMI1/DVI,HDMI2, DTV input

sources cannot be used for Monitor out.

Monitor Out Setup

S-VIDEO IN

(R) AUDIO (L) VIDEO

PC/DTV

(XGA

/480p

/720p

/1080i)

S-VIDEO

MONO

RGB INPUT

RGB/DVI INPUT

(L)

(R)

AUDIO

(L)

(R)

AUDIO

MONITOR

OUT INPUT2 INPUT1

VARIABLE

AUDIO OUT

How to connect

Use the TV’s COMPONENT (Y, PB, PR) INPUT, RGB, HDMI1/DVI or

HDMI2 jack for video connections, depending on your set-top box connec-

tor. Then, make the corresponding audio connections.

Note: HDMI(High Definition Multimedia Interface): Input that accepts uncom-

pressed digital signal and multi channel digital audio signal.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital

set-top box.)

2. Use TV/VIDEO on the remote control to select Component 1,

Component 2, RGB-DTV, HDMI1/DVI or HDMI2 source.

HDSTB Setup

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital

signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

Signal

480i

480p

720p

1080i

Component 1/2

Yes

RGB-DTV,HDMI1/DVI,HDMI2

Yes

Owner’s Manual 15

Installation

How to connect

1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product).

If you do not need to connect audio, HDMI2 port is also available for the DVI video connection.

2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGI-

TAL AUDIO(OPTICAL) port for DVI INPUT.

3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT

port located on the right side of RGB INPUT port.

How To Use

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.61)

TV/VIDEO button is also available for this purpose.

3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC

mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the

brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be

changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

How to connect

1. Connect the PC to RGB INPUT port of this TV with a RGB cable(not supplied with this product).

2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT

port located on the right side of RGB INPUT port.

How To Use

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz.

2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.61)

Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose.

3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC

mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the

brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be

changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

PC Setup

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic

card accordingly.

Resolution

640x350

640x480

800x600

Horizontal

Frequency(KHz)

31.468

31.469

37.861

37.500

70.09

59.94

72.80

75.00

48.363

56.476

60.023

Vertical

Frequency(Hz)

1024x768

Monitor Display Specifications (RGB-PC or HDMI/DVI Mode)

35.156

37.879

48.077

46.875

56.25

60.31

72.18

75.00

60.00

70.06

75.02

16 DLP Projection TV

Installation

Send the TV’s audio to external audio equipment (stereo system) via

the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio

(Optical) Output port.

2. Connect the other end of the optical cable to the digital audio (opti-

cal) input on the audio equipment.

3. Set the “ TV Speaker option - Off”in the AUDIO menu. Refer to

page 64.

See the external audio equipment instruction manual for operation.

Caution: Do not look into the optical output port. Looking

at the laser beam may damage your vision.

Digital

Digital Audio Output

Audio Output

CABLE

COMPONENT

INPUT2 INPUT1

DTV/DVD INPUT

(L)

(R)

AUDIO

ANTENNA

DIGITAL AUDIO

OPTICAL INPUT1

(COMPONENT2)

DIGITAL AUDIO

OPTICAL INPUT2

(DVI)

IEEE-1394

DIGITAL AUDIO

OPTICAL OUTPUT

DVI

G-LINK

HDMI

HDMI1

/DVI

HDMI2

Hook up Variable Audio Output, L-Audio-R to Amplifier system for

Left/Right front speaker sound.

How to connect

1. Locate the Variable Audio Out jacks on the back of your TV and the

Input jacks on the back of your stereo's amplifier.

2. Connect the two jacks, making sure that the right and left channels

are connected correctly.

3. Set up your speakers through your analog stereo amplifier, accord-

ing to the instructions provided with the amplifier.

External Stereo

PC/DTV

(XGA

/480p

/720p

/1080i)

S-VIDEO

MONO

RGB INPUT

RGB/DVI INPUT

(L)

(R)

AUDIO

(L)

(R)

AUDIO

MONITOR

OUT INPUT2 INPUT1

VARIABLE

AUDIO OUT

Owner’s Manual 17

Installation

- HDMITM, the HDMI logo and High-Definition Multimedia Interface is a trademark or registered trademark of HDMI Licensing.

- This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI).

- This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolu-

tion.

- When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output

resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI/DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's

output resolution to 1024x768, 60Hz.

- If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes

both video and audio.

- If the source device has a DVI output and no HDMI output, a separated audio connection is necessary.

How To Connect

1. Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product).

2. No separated audio connection is necessary.

How To Use

- If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto HDMI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI or HDMI2 input source in main input option on the SETUP menu.(Refer to P.61)

TV/VIDEO button is also available for this purpose.

How To Connect

1. Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product).

Do not use HDMI2 port for DVI connection if you want to connect audio.

2. A separated audio connection is necessary.

3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI

INPUT.

4. , connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port.

How To Use

- If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p.

- If the source device does not support Auto DVI, you need to set the output resolution appropriately.

To get the best picture quality, adjust the output resolution of the source device to 1280x720p.

- Select HDMI1/DVI input source in main input option on the SETUP menu.(Refer to P.61)

TV/VIDEO button is also available for this purpose.

HDMI

18 DLP Projection TV

Installation

Cable sample

HDMI Cable

(not supplied with the product)

HDMI to DVI Cable

(not supplied with the product)

Fiber Optic Digital Audio Cable

(not supplied with the product)

Analog Audio Cable(RCA type)

(not supplied with the product)

Analog Audio Cable(Stereo to RCA type)

(not supplied with the product)

Reference

Owner’s Manual 19

Installation

How to use

1. Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET.

2. Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control.

3. Select HDMI1/DVI Input source in Main Input option on the SETUP menu.(Refer to P.61)

4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in

HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the

refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics

card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.

Notes:

- Depending on the graphics card, DOS mode may not work if a HDMI to DVI Cable is in use.

- Avoid keeping a fixed image on the screen for a long period of time. The fixed image may become permanently imprinted on the

screen.

- When Source Devices connected with HDMI1/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position and Size may not fit

to Screen. As shown the picture below, press the ADJUST button to adjust the screen Position of TV SET and contact an PC

graphics card service center.

- When Source Devices connected with HDMI1/DVI Input, output TV SET Resolution(480p, 720p, 1080i) and TV SET Display fit

EIA/CEA-861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service cen-

ter.

- In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI

Input. In case that Video Resolution is not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD

display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center.

In This Mode, the Supported TV Set Resolution Specification

- 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9

- 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)

- 720 x 480 P @ 59.94Hz / 60Hz, 16:9

- 720 x 480 P @ 59.94Hz / 60Hz, 4:3

In This Mode, the Supported PC Resolution Specification

- 640 x 350 @ 70Hz

- 640 x 480 @ 60Hz

- 640 x 480 @ 72Hz

- 640 x 480 @ 75Hz

- 800 x 600 @ 56Hz

- 800 x 600 @ 60Hz

- 800 x 600 @ 72Hz

- 800 x 600 @ 75Hz

- 1024 x 768 @ 60Hz(preferred format)

- 1024 x 768 @ 70Hz

- 1024 x 768 @ 75Hz

POSITION G

SIZE

PHASE

RESET

Adjust

PC mode

20 DLP Projection TV Owner’s Manual 20

Operation

Notes:

• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

• The TV Guide On Screen and any CableCARDTM Software upgrades work while the TV is in standby

• mode. If you pull the power plug cord the TV Guide On Screen will not update its listings and no •••

•CableCARDTM Software upgrades will occur.

• After turning on the TV, it could take up to a week for the TV Guide On Screen system to receive full list-

•ings data.

Operation

Turning the TV On

urning the TV On

* In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just an

example to help you with the TV operation.

Turning on the TV just after installation

Turning on the TV (power cord is still connected)

1. Connect power cord correctly.

2. Press the POWER button on the TV. At this moment, the TV is switched to standby mode. Press the

TV INPUT, TV/VIDEO, CH (D/ E), Number (0 ~ 9) button on the remote control or press the CH (D/ E)but-

ton on the TV front panel and then the TV will switch on.

•Check the power cable.

1. If the TV was turned off with indicators on the TV

2. If the TV was turned off with the remote control and the POWER button on the TV

•Press the POWER button on the TV or press the POWER, TV/VIDEO, CH (D/ E), Number (0 ~ 9)

button on the remote control to turn the TV on.

Owner’s Manual 2121 DLP Projection TV

Operation

TV Setup

-The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use D/ Ebutton to select the OPTION

menu.

2. Press the Gbutton and then use D/ Ebutton to select Language.

3. Press the Gbutton and then use D/ Ebutton to select your desired language.

From this point on, the on-screen menus will be shown in the selected lan-

guage.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

On-screen Menus Language Selection

- Create two different types of channel lists in memory: “Custom List” and

“Favorite List” from the default channel list created from the EZ Scan channel

search.

- A Custom List can be created by toggling each channel on or off with ENTER

button. The channels in the Custom List are displayed in black color, and the

channels deleted from the Custom List are displayed in gray color. Once a

channel is highlighted you can add or delete the channel by referring to the

small window at the top-left corner of the screen.You can create your own

Favorite List.

Use the FAV button on the remote control when a channel is highlighted and

then you can add or delete the channel to/from the Favorite List.

1. Press the MENU button and then use D / Ebutton to select the SETUP menu.

2. Press the Gbutton and then use D / Ebutton to select Channel Edit.

3. Press the Gbutton. You will now see a screen filled with channel numbers and

a preview picture.

4. Use D / E/ F / G button to select a channel and then use the ENTER button to

add or delete it. Press FAV to add or delete the channel to the Favorite List.

5. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Channel Edit

Note:

• When a cable box connects to the physical channel 2, 3, or 4 in TV Guide On Screen Setup, cable channels(CATV or

CADTV) will not be editable by Channel Edit. Instead, use the cable box's Channel Edit if available.

22 DLP Projection TV Owner’s Manual 22

Operation

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

- Run EZ Scan again after any Antenna/Cable connection changes.

- A password is required to gain access to EZ Scan menu if the Lock System is turned on.

1. Press the MENU button and then use D / Ebutton to select the SETUP menu.

2. Press the Gbutton and then use D / Ebutton to select EZ Scan.

3. Press the Gbutton or ENTER button to begin the channel search.

Allow EZ Scan to complete the channel search cycle for TV, DTV, CATV, and CADTV.

EZ Scan (Channel Search)

Setup Menu Options

23 DLP Projection TV Owner’s Manual 23

Operation

- Changes the picture source so you can watch your off-air TV, cable TV, VCR,

DVD, or any other devices that are connected to your TV.

1. Press the MENU button and then use D / Ebutton to select the SETUP menu.

2. Press the Gbutton and then use D / Ebutton to select Main Input.

3. Press the Gbutton and then use D / Ebutton to select the source: Antenna,

Cable, Video1, Video2, Front Video, Component1, Component2, RGB-DTV (or

RGB-PC), HDMI1/DVI or HDMI2.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Main Picture Source Selection

1. Press the MENU button and then use D / Ebutton to select the SETUP menu.

2. Press the Gbutton and then use D / Ebutton to select Input Label.

3. Press the Gbutton and then use D / Ebutton to select the source: Video1,

Video2, Front Video, Component1, Component2, RGB, HDMI1/DVI or HDMI2.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Input Label

- Choose preset labels for your channels.

- If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a DTV chan-

nel - even if you didn't preset a label for the channel.

1. Press the MENU button and then use D / Ebutton to select the SETUP menu.

2. Press the Gbutton and then use D / Ebutton to select Channel Label.

3. Press the Gbutton. You will now see a screen filled with Labels and a preview screen.

4. Use the CH D / Ebutton to select a channel to Label.

5. Use D / E/ F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to

the selected channel.

- If you press ENTER button in TV viewing mode, you will see the channel banner.

Channel Label Setup

CADTV 27-1

CNN

Dolby Digital HD

Owner’s Manual 2424 DLP Projection TV

Operation

- Adjust the picture appearance to suit your preference and viewing situations.

1. Press the MENU button and then use D / Ebutton to select the VIDEO menu.

2. Press the Gbutton and then use D / Ebutton to select the desired picture option

(Contrast,Brightness,Color,Sharpness, or Tint).

3. Press the Gbutton and then use F / Gbutton to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the EZ PIC button repeatedly to select the picture appearance setup option as shown below:

Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports.

• You can also use the VIDEO menu to adjust EZ Picture.

2. Press the EXIT button to save and return to TV viewing.

EZ Picture

Manual Picture Control

Manual Picture Control (

(Custom option)

option)

- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the

program category.

- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ

Picture automatically changes to Custom.

-Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at

the factory and are not adjustable.

Video Menu Options

ideo Menu Options

- Use to quickly reset all the Video menu options to their original factory preset

values.

1. Press the MENU button and then use D / Ebutton to select the VIDEO menu.

2. Press the Gbutton and then use D / Ebutton to select Video Reset .

3. Press the Gbutton to reset the Video menu options to original values.

Video Reset

ideo Reset

1. Press the MENU button and then use D / Ebutton to select the VIDEO menu.

2. Press the Gbutton and then use D / Ebutton to select Color Temperature .

3. Press the Gbutton and then use D / Ebutton to select either Cool, Medium,

or Warm.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Color

Color T

Temperature Control

emperature Control

- Choose one of three automatic color adjustments. Set to warm to enhance hotter

colors such as red, or set to cool to see less intense colors with more blue.

25 DLP Projection TV Owner’s Manual 25

Operation

- Other languages may be available if a digital signal is provided by the broad-

casting station.

1. Press the EZ SOUND button repeatedly to select the appropriate sound setup as shown below:

Custom (your own settings), Normal, Stadium, News, Music and Theater.

• You can also adjust EZ Sound in the AUDIO menu.

2. Press EXIT button to save and return to TV viewing.

EZ Sound

1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.

2. Press the Gbutton and then use D / Ebutton to select the desired sound option

(Balance,Treble, or Bass).

3. Press the Gbutton and then use F / Gbutton to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Manual Sound Control (

Manual Sound Control (Custom option)

option)

1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.

2. Press the Gbutton and then use D / Ebutton to select Audio Language.

3. Press the Gbutton and then use D / Ebutton to select: English, Spanish, or

French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Audio Language

- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound

options based on the program content.

- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Custom.

-Normal, Stadium, News, Music and Theater are preset for good sound quality at the factory and are not

adjustable.

- Scans for changes in sound level during commercials, then adjusts the sound

to match the specified audio level. SoundRite makes sure that the volume level

remains consistent whether you are watching a commercial or a regular TV

program.

1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.

2. Press the Gbutton and then use D / Ebutton to select EZ SoundRite.

3. Press the Gbutton and then use D / Ebutton to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

EZ SoundRite

- Adjust the sound to suit your taste and room situations.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE Previous

English

Spanish

French

Audio Language G

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

Audio Menu Options

Owner’s Manual 2626 DLP Projection TV

Operation

1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.

2. Press the Gbutton and then use D / Ebutton to select Front Surround.

3. Press the Gbutton and then use D / Ebutton to select Off, 3D EchoSound

System or SRS (Sound Retrieval System) TruSurround XT.

• 3D EchoSound System

Creates a stunning simulated stereo effects from any mono sound and a real-

istic three-dimensional sound with a very wide and deep sound stage into

stereo sound

• SRS TruSurround XT

Takes advantage of any multi-channel format without needing to add extra

speakers or equipment. Dialog clarity, bass enrichment, and the addition of

stereo audio enhancement that produces an immersive sound experience from

standard stereo material.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Front Surround

1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.

2. Press the Gbutton and then use D / Ebutton to select TV Speaker.

3. Press the Gbutton and then use D / Ebutton to select On or Off .

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

TV Speaker On/Of

TV Speaker On/Off Setup

f Setup

- Turn TV speaker off if using external audio equipment. Feature turns the TV

Speaker option On or Off.

1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono,

Stereo, or SAP appear in turn.

• If other languages available on the digital signal, select them with the SAP button.

2. Press EXIT button to save and return to TV viewing.

Stereo/SAP

Stereo/SAP Broadcasts Setup

Broadcasts Setup

- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if

the station transmits an additional sound signal as well as the original one.

- When having selected Stereo or SAP button on the remote control, this TV can only receive the signal when the TV station

transmits the proper signals.

- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

- Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting.

- Stereo or SAP can be received in Analog channel.

- is a trademark of SRS Labs, Inc.

- TruSurround XT technology is incorporated under license from SRS Labs, Inc.

- Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Audio Menu Options

27 DLP Projection TV Owner’s Manual 27

Operation

- Timer function operates only if current time has been set.

- Off-Timer function overrides On-Timer function if they are both set to the same time.

- The TV must be in standby mode for the On-Timer to work.

- If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to

standby mode.

On/Of

On/Off

f T

Timer Setup

imer Setup

1. Press the MENU button and then use D / Ebutton to select the TIME menu.

2. Press the Gbutton and then use D / Ebutton to select Off Timer or On Timer.

3. Press the Gbutton and then use D / Ebutton to select On.

• To cancel On/Off timer function, select Off.

4. Press the Gbutton and then use D / Ebutton to set the hour.

5. Press the Gbutton and then use D / Ebutton to set the minutes.

6. For only On timer function

Press the Gbutton and then use D / Ebutton to select the channel at turn-on.

Press the Gbutton and then use D / Ebutton to set the sound level at turn-on.

7. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Auto Clock Setup

- The time is set automatically from a digital channel signal.

- The digital channel signal includes information for the current time provided by the broadcasting station.

- Set the clock manually, if the current time is set incorrectly by the auto clock function.

- When you set up TV Guide, Auto Clock menu is not selected.

1. Press the MENU button and then use D / Ebutton to select the TIME menu.

2. Press the Gbutton and then use D / Ebutton to select Auto Clock.

3. Press the Gbutton and then use D / Ebutton to select On.

4. Press the Gbutton and then use D / Ebutton to select your viewing area time

zone: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.

5. Press the Gbutton and then use D / Ebutton to set Daylight Saving Auto, Off

or On, depending on whether or not your viewing area observes Daylight

Savings Time.

6. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Manual Clock Setup

- If current time setting is wrong, reset the clock manually.

- When you set up TV Guide, Manual Clock menu is not set.

1. Press the MENU button and then use D / Ebutton to select the TIME menu.

2. Press the Gbutton and then use D / Ebutton to select Manual Clock.

3. Press the Gbutton and then use F / Gbutton to select either the year, date, or

time option. Once selected, use the D / Ebutton to set the year, date, and time

options.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Time Menu Options

ime Menu Options

Owner’s Manual 2828 DLP Projection TV

Operation

Auto Of

Auto Off

- If set to on and there is no input signal, the TV turns off automatically after 10

minutes.

1. Press the MENU button and then use D / Ebutton to select the TIME menu.

2. Press the Gbutton and then use D / Ebutton to select Auto Off.

3. Press the Gbutton and then use D / Ebutton to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Sleep

Sleep T

Timer

imer

- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.

- You can also set up the Sleep Timer in the TIME menu.

1. Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen,

followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to

count down from the number of minutes selected.

3. To check the remaining minutes before the TV turns off, press the TIMER button once.

4. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off.

Time Menu Options

ime Menu Options

29 DLP Projection TV Owner’s Manual 29

Operation

Cinema 3:2 Mode Setup

- Most movies are 24 frames/sec, but TV signal is 30 frames/sec.

This option lets the TV do 3:2 pull-down operation for you to watch

movies at the best motion appearance.

1. Press the MENU button and then use D / Ebutton to select the OPTION menu.

2. Press the Gbutton and then use D / Ebutton to select Cinema 3:2 Mode.

3. Press the Gbutton and then use D / Ebutton to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Aspect Ratio Control

- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format.

When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be dis-

played.

- If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option.

- Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)//HDMI1/DVI-DTV

(720p/1080i)/DTV(720p/1080i), HDMI2-DTV(720p/1080i) input source.

- RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.

• Set By Program

Selects the proper picture proportion to match the source’s image. (4:3 →4:3, 16:9 → 16:9)

• 4:3

Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both

the left and right sides.

• 16:9

Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

• Horizon

Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both

sides, to create a spectacular view.

• Zoom 1

Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions

of the picture will be cropped.

• Zoom 2

Choose Zoom 2 when you want the picture to be altered, both horizontally extended and vertically cropped. The

picture taking a halfway trade off between alteration and screen coverage.

• Cinema Zoom

Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or

reducing the picture, the image may become distorted.

You can adjust the enlarge proportion of Cinema Zoom using D / Ebutton. The adjustment range is 1~16.

1. Press the RATIO button repeatedly to select the desired picture format.

You can also adjust the Aspect Ratio in the OPTION menu.

Option Menu Options

Note: This feature operates only in 480i mode.

Owner’s Manual 3030 DLP Projection TV

Operation

Caption

Digital Broadcasting System Captions

- Choose the language you want the DTV/CADTV Captions to appear in.

- Languages can be chosen for digital sources only if they are included on the

program.

1. Press the MENU button and then use D / Ebutton to select the OPTION menu.

2. Press the Gbutton and then use D / Ebutton to select Caption/Text.

3. Press the Gbutton and then use D / Ebutton to select available caption lan-

guages: English, Spanish, or French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the MENU button and then use D / Ebutton to select the OPTION menu.

2. Press the Gbutton and then use D / Ebutton to select Caption.

3. Press the Gbutton and then use D / Ebutton to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Caption/T

Caption/Text

ext

Analog Broadcasting System Captions

- Select a caption mode for displaying captioning information if provided on a program.

- Analog caption displays information at any position on the screen usually the program's dialog.

- Text displays information, usually at the bottom position and is used for a data service, generally not program related.

- Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.

- This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off.

1. Press the MENU button and then use D / Ebutton to select the OPTION menu.

2. Press the Gbutton and then use D / Ebutton to select Caption/Text.

3. Press the Gbutton and then use D / Ebutton to select caption: CC1, CC2, CC3,

CC4, Text1, Text2, Text3, or Text4.

• CAPTION

The term for the words that scroll across the bottom of the TV screen; usually

the audio portion of the program provided for the hearing impaired.

• TEXT

The term for the words that appear in a large black frame and almost cover

the entire screen; usually messages provided by the broadcaster.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4.

• EZ Mute shows the selected captions option (if available on program) when the TV sound is muted

2. Press EXIT button to save and return to TV viewing.

• You can also use the OPTION menu to select Caption/Text.

Option Menu Options

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE Previous

English

Spanish

French

Aspect Ratio

Cinema 3:2 Mode

Caption

Caption / Text G

Caption Option

Language

EZ Demo

31 DLP Projection TV Owner’s Manual 31

Operation

Caption Option

- Customize the DTV/CADTV captions that appear on your screen.

1. Press the MENU button and then use D / Ebutton to select the OPTION

menu.

2. Press the Gbutton and then use D / Ebutton to select Caption Option.

3. Press the Gbutton and then use F / Gbutton to select Custom.

4. Use D / Ebutton to customize the Style, Font, etc., to your preference. A pre-

view icon is provided at the bottom of the screen, use it to see the caption lan-

guage.

• Size: Set the size the words will appear in.

• Font: Select a typeface for the words.

• Text Color: Choose a color for the text.

• Text Opacity: Specify the opacity for the text color.

• Bg (Background) Color: Select a background color.

• Bg (Background) Opacity: Select the opacity for the background color.

• Edge Type: Select an edge type.

• Edge Color: Select a color for the edges.

5. Press EXIT button to return to TV viewing or press MENU button to return

to the previous menu.

EZ Demo

Shows you how to navigate the TV's on-screen menus.

EZ Demo Use to scan the features and menu options available on your TV.

1. Press the MENU button and then use D / Ebutton to select the OPTION

menu.

2. Press the Gbutton and then use D / Ebutton to select EZ Demo, then use the G

button to start EZ Demo.

3. Press EXIT button to stop EZ Demo.

Owner’s Manual 3232 DLP Projection TV

Operation

Parental Control can be used to block specific channels, ratings and other viewing sources.

The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station.

The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories

chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be

done :

1. Set ratings and categories to be blocked.

2. Specify a password

3. Enable the lock

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV

Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating

System (MPAA) only.

Ratings for Movies previously shown in theaters:

Movie Ratings :

• Blocking Off (Permits all programs)

• G (General audience)

• PG (Parental guidance suggested)

• PG-13 (Parents strongly cautioned)

• R (Restricted)

• NC-17 (No one 17 and under admitted)

• X (Adult only)

If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

• TV-G (General audience)

• TV-PG (Parental guidance suggested)

• TV-14 (Parents strongly cautioned)

• TV-MA (Mature audience only)

• TV-Y (All children)

• TV-Y7 (Children 7 years older)

TV Rating Children:

• Age (applies to TV-Y, TV-Y7)

• Fantasy Violence (applies to TV-Y7)

TV Rating General:

• Age (applies to TV-G, TV-PG, TV-14, TV-MA)

• Dialogue - sexual dialogue (applies to TV-PG, TV-14)

• Language - adult language (applies to TV-PG, TV-14, TV-MA)

• Sex - sexual situations (applies to TV-PG, TV-14, TV-MA)

• Violence (applies to TV-PG, TV-14, TV-MA)

Input Block

• Video 1, 2, Front Video (On, Off)

• Component 1, 2 (On, Off)

• RGB, HDMI1/DVI or HDMI2 (On, Off)

Lock Menu Options

33 DLP Projection TV Owner’s Manual 33

Operation

Parental Lock Setup

1. Press the MENU button and then use D / Ebutton to select the LOCK menu.

Then, press the Gbutton

• Enter the password as requested.

• The TV is set up with the initial password “0-0-0-0”.

2. Use the D /Ebutton to choose from the following Lock Menu options. Once the

option is selected, change the settings to your preference.

• Lock System: Activates or disables the blocking scheme you set up previ-

ously.

• Set Password: Change the password by inputting a new password twice.

• Block Channel: Blocks any channels that you do not want to watch or

that you do not want your children to watch.

• Movie Rating (MPAA): Blocks movies according to the movie ratings lim-

its specified, so children cannot view certain movies. You can set the rat-

ings limit by blocking out all the movies with the ratings above a specified

level. Keep in mind that the movie ratings limit only applies to movies

shown on TV, not TV programs, such as soap operas.

• TV Rating-Children: Prevents children from watching certain children's TV

programs, according to the ratings limit set. The children rating does not

apply to other TV programs. Unless you block certain TV programs intend-

ed for mature audiences in the TV Rating - sub menu, your children can

view those programs.

• TV Rating-General: Based on the ratings, blocks certain TV programs that

you and your family do not want to view.

• Input Block: Enables you to select a source to block from the external

source devices you have hooked up.

3. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Note : If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote con

trol.

- Set up blocking schemes to block specific channels, ratings, and external viewing sources.

- A password is required to gain access to this menu.

Owner’s Manual 3434 DLP Projection TV

Operation

Cable menu options

- The Cable sub menu displays when inserting the CableCARDTM to the TV.

- The CableCARDTM type is Motorola, Scientific Atlanta (SA), or SCM etc. The

OSD (On screen display) is different from your TV according to your

CableCARDTM type.

Scrambled channel

- Insert the CableCARDTM. If you do it at first, it takes about 1 minute to

exchange the data between the TV and the CableCARDTM. Then, TV screen

displays as shown right.

- Let your cable TV service provider know the CableCARDTM ID and Host ID.

- If your cable TV service provider has registered the CableCARDTM ID and Host

ID, you can watch the premium or high value channel.

- If you ever registered to the cable TV service provider, you can watch the pre-

mium or high value channel without a message.

- If the certificate doesn’t match between the TV and the cableCARDTM,

the OSD (On screen display) displays as shown left.

In case of Scientific Atlanta CableCARD™

1. Press the MENU button and then use D / Ebutton to select the CABLE

menu.

2. Press the Gbutton and then use D / Ebutton to select your desired item.

3. Press the Gbutton.

4. Press EXIT button to return to TV viewing.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE Previous

SA CableCARD Diag Screen G

SA CableCARD/Host ID Screen

Exit

In order to start cable service for this device,

please contact SuperVision Cable at

1-800-555-8888

POD ID: 7-561-034-449-009

Host ID: 0-100-331-784-018

EXIT

CableCARD (tm) Message

Please call your operator and report an invalid CableCARDTM.

* In this manual, the OSD (On Screen Dispaly) may be different from your TV’s because it is just example to help

the TV operation.

i.e) CableCARD™/ Host ID Screen

Exit

In order to start service for

this device, please contact

customer service at

Ph#: 1-866-303-0422

CableCARD (tm): 0-010-405-698-001

HOST ID: 0-080-000-000-226

EXIT

CableCARD (tm) Message

As shown, the pairing num-

ber means your TV and

CableCARDTM ID. For fur-

ther information regarding

cable TV service, contact

your local cable TV service

provider(s).

CableCARD

CableCARD™

™Function

Function

35 DLP Projection TV Owner’s Manual 35

Operation

- If an emergency situation occurs while watching the TV/DTV/CATV/CADTV, you can see a message from cable

TV service provider(s).

- When receiving an emergency message, the message is displayed on the screen as shown below or the channel

is changed automatically to a channel that maintains the emergency message. The message will automatically dis-

appear.

Emergency Action Notification

Hurricane will be coming!!!

Cable Channel List

Emergency

Emergency Alert Message

Alert Message

1. If you enter the Channel Edit after running the EZ Scan without CableCARDTM, you can see the cable channel list as the

picture 3 above.

2. Insert the CableCARDTM. Then, the TV will receive a new cable channel list which is usually one part channel. It takes about

2~3 minutes to gather the cable channel list after inserting the CableCARDTM as the picture 4 above. (Occasionally more

than that time)

Note:

• As data gathering is done by the CableCARDTM, you may hear a fan run in standby mode.

1. 2.

3. 4.

36 DLP Projection TV Owner’s Manual 36

Operation

- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other

source will show a smaller inset image.

- Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each

source is given half the screen.

- If you set the block/rating for Lock menu options in PIP/Twin Picture mode, “Rating Blocked” doesn’t display on screen.

Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.

PIP Off

PIP Mode POP Mode Twin Picture Mode

1. Press the PIP button.

2. Select the Antenna or Cable option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+ /

PIPCH- button to select a channel for the sub picture.

(You can’t select DTV for main and sub picture simultaneously).

Repeatedly, use the SWAP button to switch the main and sub pictures.

•Component 1, Component 2, RGB-PC (or RGB-DTV), HDMI/DVI input sources for the main picture can’t be used to

swap the main and sub pictures.

Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes

the PIP source. You can also select sources for the Sub Input in the SETUP menu.

Main Picture Source Available Sub Picture Sources

DTV

Analog

Analog, Video, and Front Video

DTV, Analog, Video, and Front Video

Sub Picture Main Picture Sub Picture

F TV 2-0

TV 4-0

TV 6-0

Main Picture

Remote Control

PIP (Picture-In-Picture) / Twin Picture

Watching PIP/T

atching PIP/Twin Picture

win Picture

Selecting an Input Signal Source for PIP/T

Selecting an Input Signal Source for PIP/Twin Picture

win Picture

Swapping the PIP

Swapping the PIP/T

/Twin Picture

win Picture

TV Program selection for PIP

Owner’s Manual 3737 DLP Projection TV

Operation

In PIP mode, press the D / E/ F / Gbutton to move the sub picture to a different location on the

screen.

Use the D / E/ F / Gbutton to change main and sub picture sizes in Twin Picture mode.

If screen is adjusted to the

maximal size, the large

screen appears the black

part at both the up and

down sides.

i.e)

Moving the PIP

Moving the PIP sub picture

sub picture

Adjusting Main and Sub Picture Sizes for

Adjusting Main and Sub Picture Sizes for T

Twin Picture

win Picture

Owner’s Manual 3838 DLP Projection TV

Operation

4 : 3

16 : 9

Screen Ratio of Input Signal 4:3

Screen Ratio of Input Signal 16:9

Resolution of Input Signal 720x480i

Resolution of Input Signal 720x480p

Resolution of Input Signal 1280x720p

Resolution of Input Signal 1920x1080i

Multilingual : Input Signal have over two Audio infor-

mation. Press the SAP button to select wanted Audio.

Caption: Input Signal have over one Close service.

Press the CC button to select wanted Closed caption.

Input Signal has rating information . Refer to the

<Lock Menu>.

D (Dialogue), L (Language), S (Sex), V (Violence), FV

(Fantasy Violence)

480i

480p

720p

1080i

Operation: •Watching TV/DTV/CATV/CADTV

•Watching Video1, Video2, Video3

•Watching IEEE 1394

•In Component1, Component2, RGB,

HDMI/DVI modes, INFO button is not

working.

Function: • Show the present screen information.

• On Watching with the upper Input signal,

press the INFO button.

• Press the INFO button or EXIT button to

exit.

A: Banner information

B: Program title

C: Day, Month, Year

D: Program start time

E: Program finish time

F: Show the prosessing rate

G: Present time

H: Added information. Refer to the icon

explanation.

Brief Info.

Live Eden 1080I

Sat, Dec 20, 2003 7:00PM 9:00PM

Caption

CC 16 : 9 Wide

BCDFA

Multilingual

TV 6-0

CNBC

MONO STEREO

3:11AM

SAP

39 DLP Projection TV Owner’s Manual 39

Operation

1. Press the FREEZE button in DTV 720p, or 1080i modes.

2. Use the D / E/ F / G buttons to select the screen split zoom section.

3. To return to normal viewing, press the FREEZE button again.

- Enlarges the picture with correct proportions.

- When enlarging the picture, the image may become distorted.

- If you set the Caption on, nothing to do with the MUTE button, Caption function operates as Caption on or off.

- When you repeatedly press the MUTE button, the screen is displayed in turn. (Refer to the lower picture)

Note: EZ Mute only operates in DTV/Analog/Video/Front Video.

Mute EZ Mute

Freeze & Magnify

EZ Mute

Mute : Sound is muted. EZ Mute : a special mute mode to

activate the closed caption,

automatically.

Mute Off : Sound is enabled.

Owner’s Manual 4040 DLP Projection TV

Operation

POSITION G

SIZE

PHASE

RESET

Adjust

POSITION

SIZE

PHASE

RESET

Adjust

POSITION

SIZE G

PHASE

RESET

Adjust

POSITION

SIZE

PHASE

RESET

Adjust

POSITION

SIZE

PHASE

RESET

Adjust

Initialize Settings

No Yes

Control Move Select

Move

Phase 0

FFGG

• When RGB connect to PC input and select the RGB-PC in Main Input, this function is used.

• When HDMI/DVI connect to PC input and select HDMI/DVI input, this function is used.

• In RGB-DTV mode, SIZE and PHASE is not available.

Screen Setup for PC mode

•After connecting RGB-PC or HDMI/DVI to PC input and checking the screen quality.

- Display PC Adjust Menu using ADJUST button.

- Position : Adjust the screen position. After displaying the Adjust, select the screen position.

- Size : Adjust the screen size.

- Phase : Adjust the phase of Pixel clock.

(Only available in RGB-PC mode)

- Reset : Initializating Size, Position, Phase adjustment .

Operation

Adjustment for screen Position, Size, Phase, Reset

POSITION

SIZE

PHASE

RESET

Adjust

Size

41 DLP Projection TV Owner’s Manual 41

Programming the Remote

G The remote is a multi-brand or a universal remote . It can be programmed to operate most remote-controllable devices of

other manufacturers.

Note that the remote may not control all models of other brands.

Programming a code into a remote mode

Programming the Remote

1. To find out whether your remote can operate the device without programming, turn on the device such as a VCR and press the

corresponding device button on the remote.

After that, press the POWER button. If the device is turned off then it responds properly and the remote need not to be pro-

grammed. If not, the remote should be programmed to operate the device. The programming procedures are explained below.

2. Press the MENU and MUTE button continuously at the same time for 2 seconds, the current selected device button will be illu-

minated.

If you don't press any button for 20 seconds, the light on the device button will be turned off. In that case, you have to repeat from

step 2.

3. Enter code numbers using the number button on the remote by refering the code table on the following pages. When pressing

the button, the light blinks at a time. If the device turned off, the programming is successful.

4. Press the MENU button to store the code. After blinking twice, this code is stored.

5. Test the remote functions to see if the device responds properly. If not, repeat from step 2.

Owner’s Manual 4242 DLP Projection TV

Programming Codes

VCRs

CATV

AIWA 034

AKAI 016 043 046 124

125 146

AMPRO 072

ANAM 031 033 103

AUDIO DYNAMICS

012 023 039 043

BROKSONIC 035 037 129

CANON 028 031 033

CAPEHART 108

CRAIG 003 040 135

CURTIS MATHES 031 033 041

DAEWOO 005 007 010 064

065 108 110 111

112 116 117 119

DAYTRON 108

DBX 012 023 039 043

DYNATECH 034 053

ELECTROHOME 059

EMERSON 006 017 025 027

029 031 034 035

036 037 046 101

129 131 138 153

FISHER 003 008 009 010

FUNAI 034

GE 031 033 063 072

107 109 144 147

GO VIDEO 132 136

HARMAN KARDON

012 045

HITACHI 004 018 026 034

043 063 137 150

INSTANTREPLAY 031 033

JCL 031 033

JCPENNY 012 013 015 033

040 066 101

JENSEN 043

JVC 012 031 033 043

048 050 055 060

130 150 152

KENWOOD 014 034 039 043

047 048

LG (GOLDSTAR) 001 012 013 020

101 106 114 123

LLOYD 034

LXI 003 009 013 014

017 034 101 106

MAGIN 040

MAGNAVOX 031 033 034 041

067 068

MARANTZ 012 031 033 067

069

MARTA 101

MATSUI 027 030

MEI 031 033

MEMOREX 003 010 014 031

033 034 053 072

101 102 134 139

MGA 045 046 059

MINOLTA 013 020

MITSUBISHI 013 020 045 046

049 051 059 061

151

MTC 034 040

MULTITECH 024 034

NEC 012 023 039 043

048

NORDMENDE 043

OPTONICA 053 054

PANASONIC 066 070 074 083

133 140 145

PENTAX 013 020 031 033

063

PHILCO 031 034 067

PHILIPS 031 033 034 054

067 071 101

PILOT 101

PIONEER 013 021 048

PORTLAND 108

PULSAR 072

QUARTZ 011 014

QUASAR 033 066 075 145

RCA 013 020 033 034

040 041 062 063

107 109 140 144

145 147

REALISTIC 003 008 010 014

031 033 034 040

053 054 101

RICO 058

RUNCO 148

SALORA 014

SAMSUNG 032 040 102 104

105 107 109 112

113 115 120 122

125

SANSUI 022 043 048 135

SANYO 003 007 010 014

102 134

SCOTT 017 037 112 129

131

SEARS 003 008 009 010

013 014 017 020

031 042 073 081

101

SHARP 031 054 149

SHINTOM 024

SONY 003 009 031 052

056 057 058 076

077 078 149

SOUNDESIGN 034

STS 013

SYLVANIA 031 033 034 059

067

SYMPHONIC 034

TANDY 010 034

TATUNG 039 043

TEAC 034 039 043

TECHNICS 031 033 070

TEKNIKA 019 031 033 034

101

THOMAS 034

TMK 006

TOSHIBA 008 013 042 047

059 082 112 131

TOTEVISION 040 101

UNITECH 040

VECTOR RESEARCH

012

VICTOR 048

VIDEO CONCEPTS

012 034 046

VIDEOSONIC 040

WARDS 003 013 017 024

031 033 034 040

053 054 131

YAMAHA 012 034 039 043

ZENITH 034 048 056

058 072 080 101

Brand Codes Brand Codes Brand Codes Brand Codes

ABC 003 004 039 042

046 052 053

AJIN 112

ANTRONIK 014

ARCHER 005 007 014 024

CABLE STAR 026

CENTURION 092

CENTURY 007

CITIZEN 007

COLOUR VOICE 065 090

COMBANO 080 081

COMTRONICS 019 030

DIAMOND 023

EAGLE 020 030 040

EASTERN 057 062 066

ELECTRICORD 032

GE 072

GEMINI 008 022 025 054

GI 052 074

GOLDEN CHANNEL

030

HAMLIN 049 050 055

HITACHI 052 055

HOSPITALITY 070 077

JERROLD 002 003 004 008

009 010 052 069

074

LG (GOLDSTAR) 001 106 101 005

M-NET 037

MACOM 033

MAGNAVOX 010 012 064 079

MEMOREX 100

MOVIE TIME 028 032

NSC 015 028 038 071

073

OAK 016 031 037 053

PANASONIC 044 047

PARAGON 100

PHILIPS 006 012 013 020

065 085 090

PIONEER 034 051 052 063

076

POST NEWS WEEK

016

PRUCER 059

PTS 011 048 071 072

073 074

PULSAR 100

RCA 047

REGAL 049 050

REGENCY 057

REMBRANT 025

SAMSUNG 102 107 030 068

SCIENTIFIC ATLANTA

003 011 041 042

043 045 046

SHERITECH 022

SIGNAL 030

SIGNATURE 052

SL MARX 030

SPRUCER 047 078

STARCOM 002 004 008 009

STARGATE 008 030

TADIRAN 030

TAEKWANG 110

TAIHAN 105

TANDY 017

TEXSCAN 029

TOCOM 039 040 056

TOSHIBA 100

UNIKA 007 014 024

UNITED CABLE 004 053

UNIVERSAL 005 007 014 024

026 027 032 035

VIEWSTAR 012 015 018 086

087 088 089

ZENITH 100 114 060 093

43 DLP Projection TV Owner’s Manual 43

Programming Codes

Audio

APEX DIGITAL 022

DENON 020 014

GE 005 006

HARMAN KARDON 027

JVC 012

LG 001 010 016 025

MAGNAVOX 013

MARANTZ 024

MITSUBISHI 002

NAD 023

ONKYO 008 017

PANASONIC 003 009

PHILIPS 013

PIONEER 004 026

PROCEED 021

PROSCAN 005 006

RCA 005 006

SAMSUNG 011 015

SONY 007

THOMPSON 005 006

TOSHIBA 019 008

YAMAHA 009 018

ZENITH 010 016 025

DVD

ALPHASTAR DSR

123

AMPLICA 050

BIRDVIEW 051 126 129

CHANNEL MASTER

013 014 015 018

036 055

CHAPARRAL 008 009 012 077

CITOH 054

CURTIS MATHES 050 145

DRAKE 005 006 007 010

011 052 112 116

141

DX ANTENNA 024 046 056 076

ECHOSTAR 038 040 057 058

093 094 095 096

097 098 099 100

122

ELECTRO HOME 089

EUROPLUS 114

FUJITSU 017 021 022 027

133 134

GENERAL INSTRUMENT

003 004 016 029

031 059 101

HITACHI 139 140

HOUSTON TRACKER

033 037 039 051

057 104

HUGHES 068

JANIEL 060 147

JERROLD 061

KATHREIN 108

LEGEND 057

LG 001

LUTRON 132

LUXOR 062 144

MACOM 010 059 063 064

065

MEMOREX 057

NEXTWAVE 028 124 125

NORSAT 069 070

PACE SKY SATELLITE 143

PANASONIC 060 142

PANSAT 121

PERSONAL CABLE 117

PHILIPS 071

PICO 105

PRESIDENT 019 102

PRIMESTAR 030 110 111

PROSAT 072

RCA 066 106

REALISTIC 043 074

SAMSUNG 123

SATELLITE SERVICE CO

028 035 047 057

085

SCIENTIFIC ATLANTA

032 138

SONY 103

STARCAST 041

SUPER GUIDE 020 124 125

TEECOM 023 026 075 087

088 090 107 130

137

TOSHIBA 002 127

UNIDEN 016 025 042 043

044 045 048 049

078 079 080 086

101 135 136

VIEWSTAR 115

WINEGARD 128 146

ZENITH 081 082 083 084

091 120

HDSTB

Brand Codes Brand Codes Brand Codes Brand Codes

AIWA 014 028 070 096

125 129 139 229

230

AKAI 163

ANAM 003 014 017 023

059 106 189 216

217 235 236

BURMECTER 252

CARVER 086

CLARION 199

DAEWOO 027 053 060 084

102 148 198 221

DENON 015 075 130 143

FANTASIA 071

FINEARTS 022

FISHER 089 099

LG(GOLDSTAR) 001 021 024 029

087 107 108 110

190 191 192 210

211 212 239

HAITAI 034 035 188 222

HARMAN/KARDON 068

INKEL 037 058 062 069

078 079 095 121

122 149 150 151

152 153 154 155

157 158 159 160

189 207 222 224

225 226 227 243

247

JVC 004 013 141

KEC 185 186 187

KENWOOD 038 050 067 089

170 171 197 206

215 222

KOHEL 030

NAD 045 046

LOTTE 014 016 036 098

100 172 173 174

175 176 177 178

179 180 181 183

201 202 208 213

214 219 223 232

238 240

LXI 103

MAGNAVOX 111

MARANTZ 002 018 020 025

034 041 081 090

097 112

MCINTOSH 049

MCS 104

MEMOREX 107

NAD 046

ONKYO 013 040 041 047

048 056 057 132

133 140

OPTIMUS 158

PANASONIC 007 033 064 113

142 220 241 251

PENNEY 104

PHILIPS 026 112 143

PIONEER 039 042 043 063

065 091 093 094

115 123 127 250

QUASAR 113

RCA 080

RCX 092

REALISTIC 103 106

SAMSUNG 124 145 146 182

193 194 195 203

204 244 245 246

SANSUI 011 135 138 144

SANYO 019 083 234

SCOTT 106 186

SHARP 031 032 051 052

072 082 117 119

156 184 199 200

206 209

SHERWOOD 005 006 158

SONY 044 045 109 114

118 126 248 249

TAEKWANG 012 020 073 074

076 077 105 161

162 163 164 165

166 167 168 169

205 231 233 242

TEAC 010 085 106 136

185 187 237

TECHNICS 101 113 128 134

147 218

TOSHIBA 137

THE 061

VICTOR 088 131

WARDS 089

YAMAHA 054 055 066 092

199

Brand Codes Brand Codes Brand Codes Brand Codes

Owner’s Manual 4444 DLP Projection TV

Troubleshooting Checklist

No picture &

No sound

•Check whether the TV is turned on.

•Is the power cord inserted into wall power outlet?

•Test the wall power outlet, plug another product’s power cord into the outlet

where the TV’s power cord was plugged in.

No or poor color

or poor picture

•Select Color in the Picture menu and press the Gbutton.

(Refer to p.62)

•Keep a sufficient distance between the TV and the VCR.

•Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.)

The remote control

doesn’t work

•Check to see if there is any object between the TV and the remote control

causing obstruction.

•Are batteries installed with correct polarity (+ to +, - to -)?

(Refer to p.11)

•Correct remote operating mode set: TV, VCR etc.?

•Install new batteries. (Refer to p.11)

Picture OK &

No sound

•Press the VOLUME (G) button.

•Sound muted? Press MUTE button.

Picture appears slowly

after switching on

•This is normal, the image is muted during the TV startup process. Please

contact your service center, if the picture has not appeared after five minutes.

Horizontal/vertical bars

or picture shaking •Check for local interference such as an electrical appliance or power tool.

Troubleshooting Checklist

roubleshooting Checklist

45 DLP Projection TV Owner’s Manual 45

Troubleshooting Checklist

Poor TV input

signal •Check ANTENNA and CABLE connection.

No channel or a few

channel •Start EZ Scan.

Poor Video

signal •Check ANTENNA and CABLE connection.

Unsuitable

Aspect Ratio •You can adjust the RATIO button or Aspect Ratio in the OPTION menu.

No output from one of

the speakers •Adjust Balance in the AUDIO menu. (Refer to p.63)

Unusual sound from

inside the TV

•A change in ambient humidity or temperature may result in the unit turning off

and does not indicate a fault with the TV.

My Guide listings

disappeared after a power

failure

•You should begin to receive listings again within 24 hours.

Owner’s Manual 4646 DLP Projection TV

Troubleshooting Checklist

roubleshooting Checklist

I set a show to Auto-Tune

and it did not.

•Check the Schedule menu and verify that the show is listed as a Reminder.

• Highlight the show under Listings and do the following:

WPress the Menu key on the remote.

WUse the down arrow to highlight Edit Reminder, and press ENTER.

WVerify the Auto-Tune option reads Yes.

• The TV must be On at the scheduled time for Auto-Tune.

• If you have a cable box, check the IR cable.

I set a show with the

Power On TV option and

it did not.

•Check the Schedule menu and verify that the show is listed as a Reminder.

• Highlight the show under Listings and do the following:

WPress the Menu key on the remote.

WUse the down arrow to highlight Edit Reminder, and press ENTER.

WVerify the Power On TV option reads Yes.

A show I set to Record

did not occur.

•Make sure your recorder is turned Off before the recording begins.

• Make sure there is a tape.

• Check the Schedule menu and verify that the show is listed before recording

begins.

• Check the placement of the IR cable in front of your recorder.

I have not received any

Guide listings.

• Listings usually appear within 24 hours after a successful Setup.

• It may take up to a week to fill the Listings grid with the full 8 days of listings.

• If you see a Listings grid with the message "No Listings" displayed you should

start to receive updated program listings within 24 hours. To receive listings:

WMake sure the cable box is left On, if applicable.

WTurn off your recorder when not in use.

• If the message "No data for this screen" is displayed:

WCheck the connections between the TV, cable, antenna, and the IR cable

if using a cable box.

WVerify Setup information under Change System Settings.

WMake sure the cable box is On, if applicable.

WIf this message is still displayed after multiple days, please contact the

LG®Brand Customer Support.

Some channel numbers

in the Guide are incor-

rect.

•You can correct them using Change Channel Display under Setup.

47 DLP Projection TV Owner’s Manual 47

Maintenance

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and

a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the

screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.

Please be sure not to use a wet cloth.

If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug

the power cord to protect against possible damage from lightning or power surges.

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your

new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Cleaning the Cabinet

Extended

Extended Absence

Absence

Maintenance

48 DLP Projection TV

Product Specification

•The specifications shown above may be changed without prior notice for quality improvement.

Product Specifications

MODEL

Horizontal Size (inches)

Height (inches)

Depth (inches)

Weight (lbs.)

Power requirement

Television System

Program Coverage

Power Consumption (W)

Antenna

Audio Output (W)

Supplied Accessories

AC120V ~ 60Hz

NTSC-M, ATSC, 64 & 256 QAM

VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135. DTV 2 ~ 69

210W

75 ohm External Terminal for VHF/UHF

20Wx2

Remote control, 2 size AA batteries, D-sub 15 pin Cable

Z44SZ80

39.2

29.2

14.4

50.7

Z52SZ80

47.5

33.8

15.7

66.1

LG Electronics USA 52SZ8DUA 52" DLP PROJECTION TV User Manual User s Manual H

LG Electronics USA 52" DLP PROJECTION TV User s Manual H

USERS MANUAL

Navigation menu

Namespaces

Views

Navigation