LG Electronics USA 9QK-LCS720 CAR CD/MP3/WMA Receiver User Manual

LG Electronics USA CAR CD/MP3/WMA Receiver

User Manual

OWNER’S MANUALSMART CAR AUDIOPlease read this manual carefully before operating  your set and retain it for future reference.LCS720BI / LCS720BOLCF820BI / LCF820BOENGLISH
1  Getting StartedGetting Started2Getting Started1Safety InformationCAUTIONRISK OF ELECTRIC SHOCK  DO NOT OPENCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.WARNING: Do not install this equipment in a conned space such as a book case or similar unit.Always operate the vehicle in a safe manner. Do not become distracted by the vehicle while driving, and always be fully aware of all driving condition. Do not change settings, or any functions. Pull over in a safe and legal manner before attempting such operations. Do not use for many hours at extremely low or high temperature. (-10 °C to 60 °C)To reduce the risk of electric shock, do not remove the cover or back of this product. There are no user-serviceable parts inside. Refer servicing to qualied service personnel.To reduce the risk of re or electric shock, do not expose this product to dripping or splashing water, rain, or moisture.The temperature of unit’s outside can be extremely high, please use the unit after proper installation in your vehicle.This unit cannot play 8 cm disc (use 12 cm disc only).While driving, keep the sound volume at a proper level.Do not drop it and avoid heavy impacts at anytime.  This unit is for vehicles with a 12-volt battery and negative grounding.  Before installing it in a recreational vehicle, lorry or bus, check the battery voltage. To avoid shorts in the electrical system, be sure to disconnect the E battery cable before beginning the installation.CAUTION: This product employs a Laser System.To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service centre.Use of controls, adjustments or the performance of procedures other than those specied herein may result in hazardous radiation exposure.To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.“This device is equipped with a portable battery or accumulator. Safe way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators." The battery shall not be exposed to excessive heat such as sunshine, re or the like.Disposal of your old appliance1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.2. All electrical and electronic products shall be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.3. he correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.4. For more detailed information about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product.
Table of Contents 312345Table of Contents1  Getting Started2  Safety Information4  Front panel 4  Remote control2 Connecting5 Installation6  About detachable control panel7 Connection3 Operating8 Operation10  Listening to a CD11  Listening to music from an external device11  Listening to the radio 12  Using an USB device/ SD card 14  Listening to music by connecting iPod/iPhone15  Connecting a Bluetooth wireless technology4 Troubleshooting20 Troubleshooting5 Appendix21 SpecificationsThe unit is compatible with the steering wheel remote control. The function allows operation by sending the steering wheel remote control signal to the unit. For details, consult with your dealer.LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/EC, 2006/95/EC and 2009/125/EC.European Standards Centre:  Krijgsman 1, 1186 DM Amstelveen The Netherlands yPlease note that this is NOT a Customer Service contact point. For Customer Service Information, see Warranty Card or contact the dealer that you purchased this product.
Getting Started4Getting Started1g DISP - Press it, you can check the clock    time. - Press and hold it, you can turn on/   o the display window and the   light of LED buttons. h  Display windowi USB port j  Returns to the previous step.k BT - Activates  BT function. - Answers a call.l Y/U Skip / Search / Seek / Tune m FUNC In each mode, sets playback items. • MENU Activates setting menu.n REC Recording to USB. DEL Deleting the desired le.o  Remote Sensorp INT Intro scan.q RPT Repeats playback.r SHF  Shues playback.s W/S - Moves 10 MP3 / WMA tracks    backward or forward if there is no    folder or one folder on a CD/ USB. - Moves to the previous or next    folder if there are more than 2   folders on a CD/ USB.t Numeric buttons (1 to 6) Selects a numbered preset station in TUNER.u 6  Opens the front panel.v  AUX If connected to other portable player, you can enjoy music from it on the unit.Remote controla SRC / • OFF - When pressed, selects function    sources. - When pressed and held, powers   unit  o.b FUNC When pressed, sets playback items in each mode. • MENU When pressed and held, activates setting menu.c BAND Selects a band in Tuner mode. DRV Front panel [LCS720BI/LCS720BO][LCF820BI/LCF820BO]a SRC / • OFF - When pressed, selects function      sources. - When pressed and held, powers   unit on or o.b R Ejects a disc.c T Plays and pauses playback. MUTE Temporarily stops the sound.d LIST / ENTER / PRESET  (Volume knob) - Adjusts volume level. - Confirms the settings. - Checks tracks, les or preset     stations.e EQ Improves sound quality.f BAND - Selects a band in Tuner mode. - Moves to a next USB drive. • TA (Optional) - Searches stations that have TA /  TP   information, when it is pressed and   held. iPOD Activates iPod/ iPhone CONTROL MODE.
2 ConnectingConnecting 5Connecting2Moves to a next USB drive.d d/M Plays or pauses playback.e SHF Shues playback.f MUTE Temporarily stops the sound.g VOLUME W / S Adjusts volume level.h c / v Skip / Search / Seek / Tune  Returns to the previous step. w / s - List up / down - Adjusts settings. - Moves 10 MP3 / WMA tracks backward or forward if there is no folder or one folder on a CD/ USB. - Moves to the previous or next folder if there are more than 2 folders on a CD/ USB. ENTER / LIST - Conrms the settings. - Checks tracks, les or preset stations.i DISP - Press it, you can check the clock time. - Press and hold it, you can turn on/ o the display window and the light of LED buttons.j RPT  Repeats playback.k INT Intro scan.l Numeric buttons (1 to 6) Selects a numbered preset station in TUNER.Battery InstallationType 1Type 2 yUse only one CR2025 (3 V) lithium battery. yRemove the battery if the remote control is not used for a long period of time. yDo not leave the product in a hot or humid place. yDo not handle the battery with metallic tools. yDo not store the battery with metallic materials. , NoteInstallationBasic InstallationBefore installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.Bend the claws according to the thickness of the dashboard.Control panel1.  Remove the existing receiver unit.2.  Make the necessary connections. 3.  Install the installation sleeve. 4.  Install the unit into the installation  sleeve.Removing the existing receiver unitIf there is already an installation sleeve for the receiver unit in the dashboard, it must be removed.1.  Remove the rear support from the unit.2.  Remove the control panel and trim ring from the unit.3.  Insert the lever into the hole on one side of the unit. Perform the same operation on the other side and pull the unit out from the mounting sleeve.ISO-DIN InstallationControl panel1.  Slide the unit into the ISO-DIN frame.2.  Fit screws removed from the old unit.3.  Slide the unit and frame into the dash opening.4.  Install the dash panel or adapter plate.  (According to models, this step may not be needed.)5.  Install the trim ring to the unit.6.  Install the control panel to the unit.
Connecting6Connecting2About detachable control panel[LCS720BI/ LCS720BO]Attaching the control panel1.  Align the left side of the panel with the stopper.2.  Push the right side of panel into the unit until it clicks.Detaching the control panel1.  Press the 6 to open the control panel.2.  Lift the control panel slightly. 3.  Push the control panel to right. 324.  Pull the control panel out of the unit.5.  Put the detached control panel into the protective case.Control panelProtective Case[LCF820BI/ LCF820BO]Attaching the control panel1.  Attach part  CA of the control panel to part  CB of the unit.CDAB2.  Attach part  C of the control panel to part  D of the unit while pushing the control panel to left.3.  Close the control panel.CDABDetaching the control panel1.  Press the 6 to open the control panel.2.  Push the control panel to left.3.  Pull the control panel out of the unit.4.  Put the detached control panel into the protective case.Control panelProtective Case yThe control buttons may not work properly if the control panel is not attached properly. If this occurs, gently press the display. yDo not leave the control panel in any area exposed to high temperatures or direct sunlight. yDo not drop the control panel or otherwise subject it to strong impact. yDo not allow such volatile agents as benzine, thinner, or insecticides to come into contact with the surface of the control panel. > Caution Periodically wipe the contacts on the back of the control panel with a cotton swap moistened with alcohol. For safety, turn o the ignition before cleaning, and remove the key from the ignition switch. , Note
Connecting 7Connecting2ConnectionConnecting to a carBefore installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting.B a Not connectedabcdefghabcdefghabcdefghAAAAAAAAA a Gray : Front Right +A b Gray / Black Stripe: Front Right -A c Violet : Rear Right +A d Violet / Black Stripe: Rear Right -A e White : Front Left +A f White / Black Stripe: Front Left -A g Green : Rear Left +A h Green / Black Stripe: Rear Left -Power AntennaControl RelayTo Audio out   To Audio inAmplierSub-woofer Left  Sub-woofer Right            Front Left  Front Right             Rear Left  Rear RightAmplierB f Power Antenna (Blue)B g Not connectedB c To Ignition (Red)B h Ground (-) (Black)B d To Battery (+) (Yellow)B e Remote On  (Blue / White)B b Not connectedIgnition Switch          Wired mic (Optional)           Wired remote input (Black): Hard-wired control adapter can be connected. (Optional)Sub-woofer
3 OperatingOperating8Operating3OperationBasic operations1.  Turn the unit on by pressing any key on the unit.2.  Select a source by pressing SRC.3.  Rotate the volume knob to adjust the volume on the unit. Or press VOLUME W / S on the remote control.Turning off the sound temporarily1.  Press MUTE to mute your unit.  Or press MUTE on the remote control.2.  Press it again to cancelUsing EQ (Equalizer)EQ is to increase or decrease the signal strength of audio frequencies. The function helps you to enjoy sound more plentifully.  Press EQ on the unit repeatedly.  The indicator lights up in the following order.FLAT /XDSS+ / POP / CLASSIC / ROCK / JAZZ / VOCAL / SALSA / SAMBA / REGGAE / RUSSY / USER1 / USER23D SOUNDThis mode delivers outstanding surround sound.1.  Press and hold EQ.2.  Press and hold it again to cancel. y3D SOUND is only available when you using the CD/ USB/ SD. (Except iPod/iPhone) yWhen you are recording, 3D SOUND will be turned o automatically. , NoteChecking the clock1.  Press DISP2.  Press it again to cancelTurning off the display light1.  Press and hold DISP.2.  Press and hold it again to turn it on.Under the light-o condition, press any key, the light is turned on and then o automatically if you don't press it within a few seconds. , NoteResetting the unitYou can reset the unit when it does not operate properly.1.  Detach the control panel.Refer to page 6 for detaching the control panel.2.  Press the RESET hole with a sharp object.[LCS720BI/ LCS720BO][LCF820BI/ LCF820BO]Adjusting the general settingsYou can adjust [SOUND], [LIGHT] and [OTHER] settings.On the unit1. Pressandhold•MENU.2.  Rotate the volume knob to select [SOUND], [LIGHT], or [OTHER] and press it.3.  Rotate the volume knob to select the item and press it.4.  Rotate the volume knob clockwise or counterclockwise to adjust the level.5.  Press the volume knob to confirm the setting.  If you want to return to the previous step, press  .On the Remote Control 1. PressandholdFUNC/•MENU.2. Press w / s to select [SOUND], [LIGHT], or [OTHER] and press ENTER.3. Press w / s to select the mode and press ENTER.4. Press w / s to adjust the level.5.  Press ENTER to confirm the setting.  If you want to return to the previous step, press   .
Operating 9Operating3For [SOUND] settingYou can adjust sound quality by adjusting the level BAL (left/right speaker), FAD (front/rear speaker), SW (Subwoofer), SW-F (Subwoofer frequency), A-EQ (Auto EQ).- When you set the EQ to USER 1/2 mode. : You can adjust the level of BAS (bass), MID (middle), TRB(treble). ySW (Subwoofer)  You can adjust the volume of subwoofer. ySW-F (Subwoofer frequency)  OFF/ SW 55 Hz/ SW 85 Hz/ SW 120 Hz You can enable the subwoofer. yA-EQ (Auto EQ) ON / OFF AUTO EQ operates only in the music le supported with genre in the device. When you set AUTO EQ to ON, POP, CLASSIC, ROCK, or JAZZ is automatically selected according to the music genre.For [LIGHT] setting[LCS720BI/ LCS720BO] You can adjust the light eects by adjusting LED, DIM, or DIM LV. yLED COL1 / COL2 / AUTO : You can change the LED window color. yDIM (Dimmer) OFF / ON  : You can change the brightness of the display window during the power-on status.Settings DescriptionDIM ON The display window becomes dark.DIM OFF The display window becomes bright. yDIM LV (Dimmer Level) : When you set DIM to ON, you can adjust the dimmer level. (-2, -1, 0, +1, +2)[LCF820BI/ LCF820BO] You can adjust the light eects by adjusting LED MODE, USER LED, DIM, or DIM LV. yLED MODE : LED AUTO/ LED USER / LED 01 to 27 yUSER LED Making the desired LED color by adjusting the each level of RED, GREEN, and BLUE. (USER LED is only available when you set LED MODE to LED USER.) yDIM (Dimmer) OFF / ON  : You can change the brightness of the display window during the power-on status.Settings DescriptionDIM ON The display window becomes dark.DIM OFF The display window becomes bright. yDIM LV (Dimmer Level) : When you set DIM to ON, you can adjust the dimmer level. (-2, -1, 0, +1, +2)For [OTHER] setting yAUX (Auxiliary) ON / OFF It is possible to use auxiliary equipment with this unit. Activate the auxiliary setting when using auxiliary equipment connected to this unit. yDEMO OFF / ON You can change the initial indication on the display to information name (function name, EQ name, etc...) while listening to a source. yBEEP 2ND / ALL BEEP 2ND : The beep is generated when a key is pressed for longer than 2 seconds. BEEP ALL : The beep is generated when any key is pressed.  yCLK (Clock) For the model RDS is not supported unit or even for a RDS supported unit.-  When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourelf. Set the clock as follows ;1. Select a source to TUNER.2. Press the FUNC to select the CT and     then set CT to OFF. (Refer to the     " Adjusting TUNER settings " on     the page 11 for setting the CT     (Clock Time) ON / OFF.)3. Press and hold •MENUontheunitto     select [OTHER] and then select CLK     by rotating the volume knob.4. Set the hour by rotating the volume     knob.5. Press the volume knob to confirm     the hour.6. Set the minute by rotating the     volume knob.7. Press the volume knob to confirm     the minute.-  When RDS CT information is received;  The clock is displayed according to   the RDS CT information.-  When RDS is not supported, set the    clock according to 3 to 7 steps.
Operating10Operating3Listening to a CD[LCS720BI/ LCS720BO]1.  Insert a CD.2.  Rotate the volume knob on the unit to adjust the volume. Or press VOLUME W / S on the remote control.[LCF820BI/ LCF820BO]1.  Press the 6 to open the control panel.2.  Insert a CD.3.  Close the control panel.Make sure to press B after pressing 6 to eject a disc. Refer to the picture above. , NotePausing or restarting CD playback1. Press T on the unit to pause playback. Or press d/M on the remote control.2.  Press it to resume playback.Searching for a section within a track / file1.  [LCS720BI/ LCS720BO] Press and hold Y/U on the unit for about 1 second during playback. [LCF820BI/ LCF820BO] Push and hold Y/U clockwise or counterclockwise on the unit for about 1 second during playback). Or press and hold c / v on remote control. 2. Press T on the unit at the point you want. Or press d/M on the remote control.Skipping to another track/ file[LCS720BI/ LCS720BO]  Press Y/U on the unit. [LCF820BI/ LCF820BO] Push Y/U clockwise or counterclockwise on the unit.Or press c / v on the remote control.Or1.  Press the volume knob on the unit. Or press ENTER on the remote control.2.  Rotate the volume knob on the unit to select a desired ROOT or folder and press it. Or press w / s and press ENTER on the remote control.3.  Rotate the volume knob on the unit to select a desired track / file and press it. Or press w / s and press ENTER on the remote control. yTo skip to previous track, press briey Y within 3 seconds of playing time (LCS720BI/ LCS720BO). yTo skip to previous track, push Y counterclockwise within 3 seconds of playing time (LCF820BI/ LCF820BO).  , NoteChecking information about your musicMP3 / WMA les often come with tags. The tag gives the Title, Artist or Album.Press DISP repeatedly during MP3 / WMA / CD TEXT le playback. If there is no information, "NO TEXT" will be shown in the display window.Playing back tracks / files in a way you wantFor using applicable buttons1.  Press INT / RPT / SHF.2.  Press it again to cancel.OrUsing the FUNC buttonOn the unit1.  Press FUNC.2.  Rotate the volume knob to select an item and press it.3.  Rotate the volume knob to select the option.4.  Press the volume knob to set the option. If you want to return to the previous step, press   .On the Remote Control1.  Press FUNC / • MENU.2. Press w / s to select an item and press it.3. Press w / s to select the option.4.  Press ENTER to set the option.  If you want to return to the previous step, press   . yRPT (Repeat) The current selected tracks / les (1 RPT) or folder (  RPT) on the disc is played repeatedly. ySHF (Shue) Each les in the current selected folder  ( SHF) or all of the tracks / les (SHF) on the disc is played randomly. During random playback, even if you press Y, you won't go back to the previous track. yINT (Intro Scan) The rst 10 seconds of all tracks / les (INT) or each les in the current selected folder (  INT) on the disc are played. yDEV (Device) USB / SD  You can change the recording device. USB <-> SD yMODE  SPD REC / SPD COPY    SPD REC : The recording speed is normal. And during the recording, you can listen to the music being recorded.  SPD COPY : The recording speed is twice as fast. And during the recording, you can listen to the TUNER / DAB. But you cannot listen to the music being recorded.(DEV and MODE are only available when the disc is activating.)
Operating 11Operating3MP3 / WMA Disc compatibility with this unit is limited as follows:1.  Sampling Frequency / 8 kHz to 48 kHz (MP3) 22.05 kHz to 48 kHz (WMA).2.  Bit rate / within 8 kbps to 320 kbps (include VBR) (MP3) 32 kbps to 320 kbps (WMA).3.  CD-R / CD-RW file system should be "ISO 9660".4.  If you record MP3 / WMA files using software which cannot create a FILE SYSTEM, for example "Direct-CD" etc., it will not be possible to playback MP3 / WMA files. We recommend that you use "Easy-CD Creator" which creates an ISO 9660 file system.You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players.(Mastered / Live File System : Disc format system for Windows Vista)Customers should also note that permission is required in order to download MP3 / WMA les and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner. , Note Listening to music from an external device1.  Connect an external device to the AUX jack with line input cable.2.  Select a source to AUX.3.  Play the connected Auxiliary Equipment.Preventing radical changes in volume as switching sourcesOnly when you set AUX to ON as switching sources, you can adjust the volume level of each source to prevent radical changes in volume by selecting GAIN 0 /  +6.1. Press FUNC on the unit. Or press FUNC / • MENU on the remote control.2.  Rotate the volume knob on the unit. Or press w / s on the remote control to set the option. (GAIN 0 / +6)3.  Press the volume knob on the unit. Or press ENTER on the remote control to confirm the setting. 4.  If you want to return to the previous step, press   . Or press     on the remote control. Listening to the radio 1.  Press SRC repeatedly to select a source to TUNER.2. Press BAND repeatedly to select a desired band.3.  [LCS720BI/ LCS720BO]  For manual search, press and hold Y/U on the unit until “MANUAL“ is displayed. Then press it repeatedly to select a desired frequency. Or press and hold c / v on the remote control.  For auto search, press Y/U on the unit. Then “SEARCH” is displayed. [LCF820BI/ LCF820BO] For manual search, Push and hold Y/U clockwise or counterclockwise on the unit until “MANUAL“ is displayed. Then push it repeatedly to select a desired frequency. For auto search, Push Y/U clockwise or counterclockwise on the unit. Then “SEARCH” is displayed.(Except MW) Or press c / v on the remote control.Storing desired frequencies manually1. Press BAND to select a desired band you want to store.2.  Select the desired frequency by using Y/U on the unit. Or use c / v on the remote control.3.  press the volume knob and rotate the volume knob to select a preset station among 1 to 6 and then press and hold the volume knob until the beep sound is heard.  Or press and hold one of preset buttons among 1 to 6 on the remote control until the beep sound is heard.4.  Repeat steps 1 to 3 to preset other stations.When a station is stored on the preset numbers on which another station of the same band has already been preset, the previously preset station is automatically erased. , NoteListening to a preset station1. Press BAND repeatedly to select a desired band.2.  Press the volume knob on the unit. Or press ENTER on the remote control.3.  Rotate the volume knob to select a preset station. Or press w / s on the remote control.4.  Press the volume knob. Or press ENTER on the remote control.OrPress BAND and then press the desired preset button among 1 to 6 on the remote control.
Operating12Operating3Adjusting TUNER settingsOn the unit1. Press FUNC.2.  Rotate the volume knob to select an item and press it.3.  Rotate the volume knob to set the option and press it.4.  If you want to return to the previous step, press   .On the Remote Control1. Press FUNC / • MENU.2. Press w / s to select an item and press ENTER.3. Press w / s to set the option and press ENTER.4.  If you want to return to the previous step, press   . yPTY (Program type, RDS (OPTIONAL))  It searches the radio stations by program type of FM tuner. The program types are displayed as follows.NEWS FINANCE EASY MAFFAIRS CHILDREN LIGHT MINFO SOCIAL CLASSICSSPORT RELIGION OTHER MEDUCATE PHONE IN JAZZDRAMA TRAVEL COUNTRYCULTURE LEISURE NATION MSCIENCE DOCUMENT OLDIESVARIED POP M FOLK MWEATHER ROCK M yA / S (Auto Store)   The six strongest broadcasting frequencies will be stored under preset button 1 to 6 in the order of their signal strength. To cancel, press the volume knob. yP / S (Preset scan) Each preset station appears. To cancel, press the volume knob. ySENS (Tuner sensitivity) MID / HI / LOW In an area in which signal reception is weak, it helps the tuner to search more stations. The weaker the reception is, the lower option you should set to.RDS (OPTIONAL) yAF (Alternative Frequency) ON / OFF When the reception quality drops, the tuner automatically changes to another station in the network, broadcasting a better reception quality, using the PI and AF codes. yREG (Region) ON / OFF REG ON : The unit switches to another station, within the same network, broadcasting the same program when the receiving signals from the current station become weak. REG OFF : The unit switches to another station, within the same network when the receiving signals from the current station become weak. (In this mode, the program may dier from the one currently received.) yTA (Trac Announcement) ALARM / SEEK  TA ALARM : When the tuned station has no TP information for 5 seconds, a double beep sound is output. TA SEEK : When the tuned station does not receive TP information for 5 seconds, the receiver retunes to the next station that has the TP information. yPI (Programme Identication) SOUND / MUTE PI SOUND : When the frequency of a tuned station switches to an AF (Alternative frequency) with an unidentied PI, it keeps the sound. PI MUTE : When the frequency of a tuned station switches to an AF with an unidentied PI, it mutes the sound until the PI is identied. yCT (Clock Time) ON / OFF You can use the RDS CT information to update the time. When RDS CT information is not received and then you set CT to OFF, you can adjust the time by yourself. Refer to the page 9 for setting the clock.Using an USB device/ SD card [USB]1.  Open the USB cover.2.  Connect the USB device.3.  Press SRC repeatedly to select a source to USB.[SD]1.  Detach the control panel. (Refer to "About detachable control panel" on page 7 to 8.)2.  Connect the SD card. 3.  Attach the control panel.4.  Press SRC repeatedly to select a source to SD.[LCS720BI/ LCS720BO][LCF820BI/ LCF810DAB]Moving to another driveWhen connecting this unit to multi reader, press BAND on the unit (or DRV on remote control) to go the next drive. Each time you press the button, the driver modes change.
Operating 13Operating3Quick search of a desired file1.  Press the volume knob on the unit. Or press ENTER on the remote control.2.  Rotate the volume knob on the unit to select a desired ROOT or folder and press it. Or press w / s and press ENTER on the remote control.3.  Rotate the volume knob on the unit to select a desired file and press it. Or press w / s and press ENTER on the remote control.Deleting the desired fileYou can select and delete a playable le you want.1.  Select the desired file in the same way as "Quick Search of a desired file"2.  Press REC and then "DELETE?" displayed. Press it again to delete.When the delete operation is started, playing is stopped. When the delete operation is ended, the list of les is displayed. If you do not select a le within few seconds, or press the  , the rst le is played.Other functions are same with "Listening to a CD". Refer to page 9 to 10. , NotePlayable USB device Requirement yDo not extract the USB device during operation (play, etc.).  yAn USB device which requires additional programme installation when you have connected it to a computer, is not supported. yRegular back up is recommended to prevent data loss. yIf you use a USB extension cable, USB HUB, USB Multi-reader, or external HDD, the USB device may not be recognized. yWhen you connect a partitioned USB device into the unit, only the rst partition is recognized on it.  ySome USB device may not work with this unit. yDigital camera and mobile phone are not supported. yUSB Port of the unit cannot be connected to PC. The unit cannot be used as a storage device. yUsing FAT (16 / 32) le system is supported. Using NTFS le system is supported to read only.Recording to USB device / SD card[USB]1.  Open the USB cover and connect it to the unit. 2.  Select one of the following lists. (CD, FM tuner, Bluetooth Handsfree)3.  Press REC to start recording. For one track/ file recording, press it once. For all tracks or files in the current selected folder recording, press and hold it until the beep sound is heard.4.  Press it again to stop.[SD]1.  Detach the control panel and connect it to the unit. Then attach the control panel. (Refer to "About detachable control panel" on page 7 to 8.)2.  Select CD only.3.  Press REC to start recording. For one track/ file recording, press it once. For all tracks or files in the current selected folder recording, press and hold it until the beep sound is heard.4.  Press it again to stop. y[USB] Only in CD, FM tuner, DAB and Bluetooth Handsfree, recording is available. [SD] Only in CD, recording is available. yDo not remove the USB device / SD card during recording, or an incomplete le may be made and not deleted on PC. yWhen USB device memory is full, "MEMORY FULL" displays and stops recording.  yWhile FM tuner recording, the broadcastings are recorded as a le every 20 minutes. yYou can adjust the recording speed. (Refer to the page .) , Note12.)The making of unauthorized copies of copy-protected material, including computer programs, les, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal oense. This equipment should not be used for such purposes.Be responsible Respect copyrights
Operating14Operating3Listening to music by connecting iPod/iPhoneYou can enjoy iPod / iPhone-stored music on the unit by connecting it to the USB connector using the appropriate cable.1.  Open the USB cover.2.  Connect the iPod / iPhone.3.  Press SRC to select a source to USB.Pausing or restarting playback1. Press T on the unit to pause playback. Or press d/M on the remote control.2.  Press it to resume playback.Searching for a section within a file[LCS720BI/ LCS720BO]  During playback, press and hold Y/U and then release at a point you want.[LCF820BI/ LCF820BO]  During playback, push and hold Y/U clockwise or counterclockwise on the unit and then release at a point you want.Skipping to another file[LCS720BI/ LCS720BO]  Press Y/U on the unit. [LCF820BI/ LCF820BO] Push Y/U clockwise or counterclockwise on the unit.Or press c / v on the remote control.Or1.  Press the volume knob on the unit. Or press ENTER on the remote control.2.  Rotate the volume knob on the unit to select a desired category and press it. Or press w / s and press ENTER on the remote control.3.  Rotate the volume knob on the unit to select a desired file and press it. Or press w / s and press ENTER on the remote control.Checking information about your musicMP3 / WMA les often come with tags. The tag gives the Title, Artist or Album.Press DISP repeatedly during MP3 / WMA le playback. If there is no information, "NO TEXT" will be shown in the display window.Playing back files in a way you wantOn the Unit1.  Press FUNC.2.  Rotate the volume knob to select an item and press it.3.  Rotate the volume knob to select the option.4.  Press the volume knob to set the option. If you want to return to the previous step, press   .On the Remote Control1.  Press RPT / SHF.2.  Press it again to cancel.Or1.  Press FUNC / • MENU.2. Press w / s to select an item and press ENTER.3. Press w / s to select the option.4.  Press ENTER to set the option.  If you want to return to the previous step, press   . yRPT (Repeat) The current selected le (1 RPT) or les on the iPod / iPhone is played repeatedly. ySHF (Shue) Each le in the currently selected album  ( SHF) or all of the les (SHF) on the iPod / iPhone are played randomly. During random playback, even if you press Y, you won't go back to the previous le. ySPD (BOOK SPEED) You can adjust the audiobook speed of iPod / iPhone to NOR (Normal), SLOW or FAST.Playing back files by music menusYou can check les by music menus and play it back.1. Press the volume knob on the unit. Or press ENTER on the remote control.2.  Rotate the volume knob on the unit to select a music menu and press it. Or press w / s on the remote control.3.  Rotate the volume knob on the unit to select a file. Or press w / s on the remote control.4.  Press the volume knob on the unit to confirm the setting. Or press ENTER on the remote control.5.   If you want to return to the previous step, press   .      Or press     on the remote control.
Operating 15Operating3iPod / iPhone CONTROL MODEYou can control on the unit and iPod / iPhone. yPress iPOD on the unit. Then playback is paused. And you can control on the unit and iPod / iPhone. yWhile using the iPod/iPhone CONTROL MODE, any functions are not available on the unit.   yPress iPOD again to cancel the iPod / iPhone CONTROL MODE.Compatible iPod / iPhone models yiPod classic  yiPod nano (1st / 2nd / 3rd / 4th / 5th / 6th generation) yiPod touch (1st / 2nd / 3rd / 4th generation) yiPhone yiPhone 3G / 3GS / 4We recommend that you use the OS Version 4.2.1 or more.“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specically to iPod or iPhone respectively, and has been certied by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.  Please note that the use of this accessory with iPod, iPhone may aect wireless performance. Connecting a Bluetooth wireless technologyBefore you start the pairing procedure, make sure the Bluetooth wireless technology is turned on in to your phone. Refer to your phone’s user guide. Pairing links your unit and phone with Bluetooth wireless technology, and is required only once for the initial setup. If the connection is successful, the phone is registered (Device 1 to 10). The process of pairing may be dierent depend on the phones. The PIN CODE is 1234.ON PLAYER1. Enter the menu. BT2. Find the "CONNECT" menu.Rotate the    volume knob3. Enter the "CONNECT" menu.Press the    volume knob4. Select the "SEARCH" menu.Rotate the    volume knob5. Search the phones supported Bluetooth wireless technology.Press the    volume knob6. Select a phone you want to connect.Rotate the    volume knob7. Connect the phone.Press the    volume knobMicrophone (OPTIONAL) yBuilt-in microphone (Only LCS720BI/ LCF820BI)[LCS720BI] [LCF820Bi] yExternal microphone (Only LCS720BO/ LCF820BO) The microphone needs to be close to and pointed toward the person speaking. Install the microphone as shown below.Microphone unitIf you power o the unit while talking on the phone through the unit by using the BT function, the function is deactivated and you can talk on the phone directly. , Note
Operating16Operating3Using a Bluetooth wireless technologyTo Do thisDisconnecting a phone(BT -> CONNECT -> LIST -> Connected device name -> DISCONN).Answering and Ending a callpress BTTo end a call, press Rejecting a call press Making a call saved as a preset numberPress BT and a preset number (1 to 6).Checking missed callsWhen the “  ? ” appears, go to the menu (BT-> CALL -> LASTCALL). You can check the list of missed call. yThe lists of LASTCALL are sorted from newest to oldest entries. yWhen you want to make an international call, press U to add “+” and to delete it press again. y“+” can only be added when the detail list of LASTCALL is selected. yYou can record the Bluetooth Handsfree to USB. (Refer to the page 13.) , NoteAudio transferIt is possible to switch the audio connection between your phone equipped with Bluetooth wireless technology and this unit.1. Press BT to answer the call.2. Press BT again. The “PRIVATE” is displayed.If the private mode is selected on the unit, press BT to return to the call to handsfree mode.Playing MP3 filesWhen you turn Bluetooth on, your device supported Bluetooth wireless technology displays “Bluetooth” on the home screen. The Bluetooth remains on until you turn the device o. Press SRC repeatedly to select “BT”. To play an MP3 le stored on your device. Refer to the phone’s user guide for using this function. This feature is only available on phones with A2DP (Advanced Audio Distribution Prole).Adjusting the setting1.   Press BT.2.   Rotate the volume knob to select an item and press it.3.   Rotate the volume knob to set the option and press it.4.   If you want to return to the previous step, press   .CALL yLASTCALL Phone number list (Received, Dialed, Missed). CALL -> LASTCALL -> Select the phone number -> Press the volume knob -> Display the information -> Press the volume knob -> DIAL, SAVE, DELETE menu will be displayed.  -  To call the phone number, DIAL -> Press the volume knob.   -  To save the phone number, SAVE -> Press the   volume knob -> select the preset number (1 to     6) -> Press the volume knob.  -    To delete the selected phone number, DELETE ->   Press the volume knob -> NAME -> Press the   volume knob.  -  To delete all phone number, DELETE -> Press the   volume knob -> ALL -> Press the volume knob. yDIAL Enters the number directly on the unit. To select the 0 to 9 rotate the volume. Press U to make the phone number. To call it, Press the volume knob. yPRESET Checks and deletes/dials the phone number saved preset number.  CALL -> PRESET -> Select the preset number and press the volume knob -> Display the information -> Press the volume knob -> DIAL, DELETE menu will be displayed.   -  To call the phone number, select DIAL and Press   the volume knob.  -  To delete the selected phone number, DELETE ->   NAME -> Press the volume knob.  -  To delete all phone number, DELETE -> ALL ->   Press the volume knob.
Operating 17Operating3P-BOOK yLIST Checks the list of the phone numbers saved by phonebook. ySEARCH Searches the phone number in the list.  yGET Getting the phonebook from the phone automatically. This menu is only available on phones with PBA / PBAP (Phone Book Access Prole).CONNECT yLIST Checks the list of the Connected Device Name. ySEARCH Searches the phones available to connect. The Connected Device Name is displayed on the top. SETUP yVISIBLE Makes it is impossible to search this unit. (SHOWN <-> HIDDEN) yAUTO CON Adjusts connection with automatically or not. (ON <-> OFF) yAUTO ANS Adjusts answering automatically or not.  (MANUAL <-> AUTO) yMIC VOL Adjusts microphone volume on the phone from 1 to 5. While you are on the phone with Bluetooth wireless technology, press Y/U (or c / v on the remote control) to adjust the MIC volume. yREDIAL Adjusts the counts of redial. (1 TIME <-> 2 TIMES)INFO yNAME Changes the name of this unit. yADDRESS Checks the address. yPIN-CODE Changes the PIN code. Default is 1234.WICS (Wireless Controller & Synchronization)You can control the unit by using the "WICS" application.1.  Search the “WICS” application and install it.   [Displays installed "WICS" application]2.  Pairing links your unit and iPhone with Bluetooth wireless technology. (Refer to the page 15.)3.  When you run the “WICS” application, activating source is displayed after initial screen. Then you can control the unit on iPhone. [Initial screen]                [Tuner screen]You can select a source by pressing "SOURCE".    [Source Mode screen]
Operating18Operating3Phone compatibility listBluetooth list and manufacturing company applicable.                                     A : Audio Streming (A2DP)                                    H : Handsfree                            P : Phonebook Sync (GET)Company    List H A P Company    List H A P Company    List H A P Company List H A PNokia E615200N80N70N72N91325061106288E90N73N95N77E71E75N975800 (Xpress music)C6E5E52X6N97-1N9006710 (Navigator)0000000000000000000000000000000000000000000000000000MotorolaSAMSUNGROKR E6V3xRIZR K1V9Z8V9rXT701XT720 (MOTOROI)Milestone DroidD900SGH-U600SGH-Z240SGH-F300SGH-E890SGH-E950SGH-F210SGH-G600i-900F330F480L878M8800 PIXONS56030000000000000000000000000000000000000000000000SAMSUNGSONYERICSSONS8003 JET(8GB)i8510 INNOV8 (16G)i8910 Omnia HDU808B5722B7330 (Omnia Pro)B7620 (Giorgio Armani)C3303K (Champ)M5650U (Lindy)M8910 (Pixon12)S7350S8500 (Wave)i5503 (Galaxy 5)i5700 (Galaxy Spica)i9000 (Galaxy S(16G))T959 Galaxy TabW880Z610W300K800i P990iW910iC702i000000000000000000000000000000000000000000000000000000000000000000SONYERICSSONLGG705W595W705W980iXperia-X1VizazXperia-X2Xperia-X10KE850KU250KU970KS10KC550KC780KC910(Renoir)KF350(IceCream)KF600KF700KF750(Secret)KF900(PRADA2)KM380KM900(Arena)KP500(Cookie)KT5200000000000000000000000000000000000000000000000000000000000
Operating 19Operating3Bluetooth list and manufacturing company applicable.                                     A : Audio Streming (A2DP)                  H : Handsfree             P : Phonebook Sync (GET)Company    List H A P Company    List H A PLGRimKT610KU990GD900BL40 (New Chocolate)KM335GD510 (POP)GD880GM730GS500 (Cookie Plus)GT505GT540GW305GX500Bold 9700Storm2 95500000000000000000000000000000000000000000APPLEASUSHTCiPhoneiPhone 3GS (16GB)iPhone 3GS (32GB)iPhone 4G (16GB)I-PadP750Goole G1Magic G2Hero G3Touch2LegendNexus OneDesire00000000000000000000000000000000  yWhen the phone features <Bluetooth Power Save> function, you should make the function turned on to maintain connection. yWhen you switch the call mode from handsfree to phone, the connection may be disconnected. ySome phones don’t support Reject function. yLow battery in phone may cause the problems. , Note“The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners.”Bluetooth® wireless technology is a system which allows radio contact between electronic devices within a max range of 10 meters.Connecting individual devices under Bluetooth® wireless technology does not incur any charges. A mobile phone with Bluetooth® wireless technology can be operated via the Cascade if the connection was made via Bluetooth® wireless technology.Operating condition for using a Bluetooth wireless technology function yClose windscreen. yTurn o the air conditioner / heater. yStop the vehicle or drive at low speed. yMake the call in a quiet location.-  There may be differences in call quality depending on phone type, road conditions     weather, etc.-  Using the phone while driving may cause unexpected accidents.-  The Bluetooth wireless technology function may not operate properly with certain     types of phones equipped with Bluetooth wireless technology.
4 TroubleshootingTroubleshooting20Troubleshooting4TroubleshootingSymptoms  Cause SolutionPower doesn't turned on.The unit doesn't operate.Leads and connectors are not properly. Conrm once more that all connections are correct.The fuse is blown.Rectify the problem that caused the fuse to blow, and then replace it. Be very sure to install the correct fuse with the same rate.Noise and other factors are causing the built in microprocessor to operate incorrectly.Turn the unit o and then on again.No sound is heard. Cables are not connected correctly. Connect the cables correctly.There's audio skipping. This unit is not rmly secured. Secure this unit rmly.The playback is not possible. The disc is dirty. Clean the disc.The disc of unplayable type is loaded.  Check what type the disc.Radio stations cannot be tuned in. The signal strength of the stations is too weak. (When tuning in with automatic tuning.)Tuned in the stations manually.No station has been preset or preset stations have been cleared. (When tuning by scanning preset stations.)Preset the stations. iPod/ iPhone does not work. Check whether iPod / iPhone is connected to the unit correctly.Connect it to the unit correctly.The unit does not operate correctly even when the appropriate remote control buttons are pressed.Battery power is low. Load a new battery.
5 AppendixAppendix 21Appendix5SpecificationsGeneralOutput Power : 53 W x 4 CH (Max.)Power Source : DC 12 VSpeaker impedance : 4 ΩGround System : NegativeDimensions (W x H x D) : (178 x 50 x169) mm (without Control Panel)Net Weight : 1.37 kgTUNERFM Tuning Range : 87.5 MHz to 108.0 MHz S / N Ratio : 55 dB Distortion : 0.7 % Usable Sensitivity : 12 dBµVAM (MW) Tuning Range : (520 to 1720) kHz or (522 to 1620) kHz S / N Ratio : 50 dB Distortion : 1.0 % Usable Sensitivity : 28 dBµVCDFrequency Response : 20 Hz to 20 kHzS / N Ratio : 80 dBDistortion : 0.12 %Channel Separation (1 kHz) : 55 dBAUXFrequency Response : 20 Hz to 20 kHzS / N Ratio : 80 dBDistortion : 0.1 %Channel Separation (1 kHz) : 45 dBMax Input Level (1 kHz) : 1.1 VUSBVersion : USB 1.1 or USB 2.0 Full SpeedBus Power Supply (USB) :  DC 5 V   1.5 ASDDistortion : 0.1 %BluetoothTX POWER 4 dBmVersion Bluetooth Speci cation 2.1 + EDRLine OUT Frequency Response : 20 Hz to 20 kHzOutput Voltage : 2 V (Max.)Subwoofer Frequency Response : 20 Hz to 120 HzOutput Voltage : 2 V (Max.) yDesign and specications are subject to change without notice.

Navigation menu