LG Electronics USA 9QK-R2 Wireless Audio Transceiver Module User Manual R2 English manual R2x

LG Electronics USA Wireless Audio Transceiver Module R2 English manual R2x

User manual

tGuGaGyYGwGk.The Module is an OEM module (35x35mm) based on the SMSC DARR83. It is an uncompressed wireless digital audio transceiver operating in the 2.4GHz, 5.2GHz and 5.8GHz bands. The wireless audio link supports up to 4 stereo audio streams and comes together with additional features such as: data encryption, pairing functionality, bi-directional control data messages, low power audio snooze mode, WLAN detection and Automatic Frequency Allocation. The DARR83 chip itself provides the basic functions of Audio Processing and buffering, Data Link Layer and Physical Layer. The module integrates all functionality for a wireless digital audio connection, comprising: x DARR83 Wireless Audio Processor x 2.4GHz/ 5.2GHz/ 5.8 GHz RF Transceiver x Embedded Antennas x Digital audio interfaces (I2S and/or S/PDIF) x I2C control interface x 26 pins interface connector (FFC) for power, digital audio and control interface and GPIOs x Built-in 1MB SPI interface Flash 3V 4KB uniform sector RFmGi.2.4GHz: 2412 – 2464MHz 5.2GHz: 5180 – 5240MHz 5.8GHz: 5736 – 5814MHz. RFw.For 2.4GHz application (VCC=3.3V, 25°C) w t {U t |RF Frequency Range 2400 2483.5 MHz Number of RF -j Carries in the spectrum 3 Transmission Power 16 dBm mGOGGGPCh1 2412 MHz Ch2 2438 Ch3 2464 jGSpacing 26 MHz RF i Null-to-null 22 MHz Rx z -83 dBm hGDiversity Tx/Rx ON For 5.2GHz application (VCC=3.3V, 25°C)
w t {U t |RF Frequency Range 5150 5250 MHz Number of RF -j Carries in the spectrum 3 Transmission PowerDepending on antenna design8 dBm mGOGGGPCh1 5180 MHz Ch2 5210 Ch3 5240 jGSpacing 30 MHz RF i Null-to-null 22 MHz Rx z -81 dBm h Diversity Tx/Rx ON For 5.8GHz application (VCC=3.3V, 25°C) w t {U t |RF Frequency Range 5725 5875 MHz Number of RF -j Carries in the spectrum 3 Transmission PowerDepending on antenna design16 dBm mGOGGGPCh1 5736 MHz Ch2 5762 Ch3 5814 jGSpacing 26 MHz RF i Null-to-null 22 MHz Rx z -81 dBm h Diversity Tx/Rx ON hG.h : 24Bit. kGtGz¡ : 32Bytes CRC : 16, 24 and 32Bit wv~ly- Supply Voltage : 3.1V(Min), 3.3V(Typ), 3.5V(Max) - Peak to Peak Ripple : 100mV(Max). - Operating Temperature : -10C(Min), 25C(Typ), 60C(Max)
Evaluation Board Usage{Gn|pGGGGGGGGGGUStep 1: Double-click on the GUI Icon or shortcut to run the program. Step 2:yGGGGUjGppGhGGGOGGGGP.Step 3: Make sure the evaluation boards is turned on.. Step 4: Connect the USB cable between your notebook/PC and the evaluation board. If USB drivers are required to be installed, use the one provided in the GUI package. .Step 5: Setup your Com Port in Com Port Settings. Connect the USB one by one and select each unique USB port setting for each evaluation board. 1) Click the [Refresh] button. 2) Select the EVK ID, for example “A3UNG243”, to access the 4ch EVK connected to the R2 3) Click the [Apply] button. 4) (Optional) If the “A3UNG243”option cannot be selected from the drop down menu, click the [Disconnect] button before repeating steps 1 ~ 3. 21 3 4
Once the connection is successful, you should see READY in Module Status. . If you see NOT FOUND, please check that the USB cable is properly connected/loose or 5V DC Power is plugged in. Step 6: At the top-left corner of the GUI, click Help and click About. The current firmware version is shown as Evaluation Kit Version X.X.X. The current GUI version is shown as Configuration Software GUI Version X.X.X. Step 7: Setup your choice of application in the Application Selection (Power-up Settings)mGGGGGGGGSGGGGGGGGGGGGlGGOl}rPUzGGGOGGGGGzGGPPress this button whenever there are any changes in this section to update the module settings Select the Frequency band (2.4GHz or 5.2GHz or 5.8GHz) to operate after Configuration Select CU or MU mode
Step 8: Click [Config] button (upon every change) to configure the evaluation board. 26Pin InterfacewpuGJG wpuGuhtlG puVv|{G klzjypw{pvuGXG }kkG wG pGwaGZUZ}UGYG nukG n nukGZG tjsrG pG Y[U\]to¡GtGjGG[G i|slslkG pVvG nwpvXZG\G ylkslkG pVvG nwpvYZG]G zkpv~GOmylxihukPG pVvG nwpv\G^G zkpvGOkh{hXPG pVvG nwpvXXG_G zkpvGOkh{hYPG pVvG nwpv]G`G zkpvGO|wspurGkh{hPG pVvG nwpvXYGXWG pYjzjszs}G TG pYjGzsh}lGOzjsPGXXG pYjzkhzs}G TG pYjGzsh}lGOzkhPGXYG zwpkpG TG zwpGkh{hGpuGXZG zwpkvG TG zwpGkh{hGv|{GX[G zwpjsrG TG zwpGjsvjrGX\G zwpjzG TG zwptvklGX]G zwp~wG pVvG nwpvXGX^G ylzl{G TG ylzl{GX_G wzluzlG pVvG nwpvYGX`G wj{sG pVvG nwpv^GYWG w~tyz{G pVvG nwpv[GYXG htwwkuG pVvG nwpvZGYYG htwzkG pVvG nwpvX[GYZG ~pylslzzGylhkG pVvG nwpvX\GY[G ijrGOyvslGXPG pVvG nwpv_GY\G nukG n nukGY]G syjrGOyvslGWPG pVvG nwpvXWG
Approval StatementsHereby, LG Electronics Inc. declares that this device is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: BEJ9QK-R2 This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux conditionssuivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. The host device must be labeled to display the Industry Canada certification number of the module. Contains transmitter module IC: 2703H-R2 Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module. Contient module émetteur IC : 2703H-R2 Caution: Any changed or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate this equipment. Attention: Toute changé ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement.IMPORTANT NOTE This device complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators and following statements shall be included to host user manual1) The antenna must be installed such that 20cm is maintained between the antenna and users. 2) This module may not be co-located with any other transmitters or antennas. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC & IC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC & IC authorizations. This module has been designed for indoor used only. Therefore the end-product with this module installed is permitted to use indoors only. NOTE IMPORTANTE Cet appareil est conforme aux limites de la FCC et IC exposition aux radiations dans un environnement non contrôlé. Cet appareil doit être installé et utilisé avec distance minimum de 20cm entre l'élément rayonnant de cet appareil et l'utilisateur. Cet appareil ne doit pas être co-localisés ou fonctionnant en conjonction avec une autre antenne ou transmetteur. Cet appareil est conçu uniquement pour les intégrateurs OEM et les déclarations suivantes doivent être incluses à accueillir manuel de l'utilisateur 1) L'antenne doit être installée de telle sorte que 20cm est maintenue entre l'antenne et les utilisateurs 2) Ce module ne peut pas être co-localisés avec les autres émetteurs ou les antennes. Aussi longtemps que deux conditions précitées sont remplies, le test du transmetteur supplémentaires ne seront pas tenus. Toutefois, l'intégrateur OEM est toujours responsable de tester leurs produits finis pour toutes les exigences de conformité supplémentaires avec ce module installé. Dans le cas où ces conditions ne peuvent pas être remplies, alors la FCC et IC autorisations ne sont plus considérés comme valides et l'ID de la FCC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera responsable de réévaluer le produit final, y compris l'obtention de ce module et séparée de la FCC et IC autorisations Ce module a été conçu pour l'intérieur utilisé seulement. Par conséquent, le produit final avec ce module installé est autorisé à utiliser uniquement à l'intérieur.
FCC Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. We will not use this module in devices that may be used outdoors. IC Radio Frequency Interference Requirements Cet appareil est restreint à une utilisation intérieure en raison de son fonctionnement dans la gamme 5.15 à 5.25 GHz. Nous n'allons pas utiliser ce module dans des appareils qui peuvent être utilisés à l'extérieur. •All relevant regulatory user statements regarding FCC and IC on this manual shall be placed into the user manual of the host device. •Toutes les déclarations pertinent es de réglementation concernant l'utilisateur de la FCC et IC sur ce manuel doit être placé dans le manuel utilisateur de l'appareil hôte.

Navigation menu