LG Electronics USA 9QK-T2 Wireless Audio Transceiver Dongle User Manual T2 English manual T2x

LG Electronics USA Wireless Audio Transceiver Dongle T2 English manual T2x

User manual

tGuGaG{YG
G
wGk
.
The Module is an OEM module (35x35mm) based on the SMSC DARR83. It is an uncompressed wireless digital
audio transceiver operating in the 2.4GHz, 5.2GHz and 5.8GHz bands. The wireless audio link supports up to 4
stereo audio streams and comes together with additional features such as: data encryption, pairing functionality, bi-
directional control data messages, low power audio snooze mode, WLAN detection and Automatic Frequency
Allocation. The DARR83 chip itself provides the basic functions of Audio Processing and buffering, Data Link
Layer and Physical Layer. The module integrates all functionality for a wireless digital audio connection,
comprising:
x DARR83 Wireless Audio Processor
x 2.4GHz/ 5.2GHz/ 5.8 GHz RF Transceiver
x Embedded Antennas
x Digital audio interfaces (I2S and/or S/PDIF)
x I
2C control interface
x 26 pins interface connector (FFC) for power, digital audio and control interface and GPIOs
x Built-in 1MB SPI interface Flash 3V 4KB uniform sector
RF
mGi
.
2.4GHz: 2412 –2464MHz
5.2GHz: 5180 – 5240MHz
5.8GHz: 5736 – 5814MHz.
RF
w
.
For 2.4GHz application (VCC=3.3V, 25°C)
w t {U t |
RF Frequency
Range
2400 2483.5 MHz
Number of
RF -j
Carries in the spectrum 3
Transmission
Power
18 dBm
mG
OGG
GP
Ch1 2412 MHz
Ch2 2438
Ch3 2464
jGSpacing 26 MHz
RF i Null-to-null 22 MHz
Rx z -83 dBm
h Diversity Tx/Rx ON
W5#lv#xvhg#iru#Dxglr#surgxfwv#pdgh#e|#OJ#Hohfwurqlfv#Lqf1#vxfk#dv#Krph#Wkhdwhu1
For 5.2GHz application (VCC=3.3V, 25°C)
w t {U t |
RF Frequency
Range
5150 5250 MHz
Number of
RF -j
Carries in the spectrum 3
Transmission
Power
Depending on antenna
design
9.5 dBm
mG
OGG
GP
Ch1 5180 MHz
Ch2 5210
Ch3 5240
jGSpacing 30 MHz
RF i Null-to-null 22 MHz
Rx z -81 dBm
h Diversity Tx/Rx ON
For 5.8GHz application (VCC=3.3V, 25°C)
w t {U t |
RF Frequency
Range
5725 5875 MHz
Number of
RF -j
Carries in the spectrum 3
Transmission
Power
Depending on antenna
design
16.5 dBm
mG
OGG
GP
Ch1 5736 MHz
Ch2 5762
Ch3 5814
jGSpacing 26 MHz
RF i Null-to-null 22 MHz
Rx z -81 dBm
h Diversity Tx/Rx ON
hG
.
h : 24Bit.
kGtGz¡ : 32Bytes
CRC : 16, 24 and 32Bit
wv~ly
- Supply Voltage : 3.1V(Min), 3.3V(Typ), 3.5V(Max)
- Peak to Peak Ripple : 100mV(Max).
- Operating Temperature : -10C(Min), 25C(Typ), 60C(Max)
Evaluation Board Usage
{Gn|pGGGGGGGGGGU
Step 1: Double-click on the GUI Icon or shortcut to run the program.
Step 2:yGGGGU
jGp
pGh
GGGOGGGGP.
Step 3: Make sure the evaluation boards is turned on..
Step 4: Connect the USB cable between your notebook/PC and the evaluation board.
If USB drivers are required to be installed, use the one provided in the GUI package.
.
Step 5: Setup your Com Port in Com Port Settings.
Connect the USB one by one and select each unique USB port setting for each evaluation board.
1) Click the [Refresh] button.
2) Select the EVK ID, for example “A3UNG243”, to access the 4ch EVK connected to the T2.
3) Click the [Apply] button.
4) (Optional) If the “A3UNG243”option cannot be selected from the drop down menu, click the
[Disconnect] button before repeating steps 1 ~ 3.
21 3 4
Once the connection is successful, you should see READY in Module Status.
.
If you see NOT FOUND, please check that the USB cable is properly connected/loose or 5V DC
Power is plugged in.
Step 6: At the top-left corner of the GUI, click Help and click About.
The current firmware version is shown as Evaluation Kit Version X.X.X.
The current GUI version is shown as Configuration Software GUI Version X.X.X.
Step 7: Setup your choice of application in the Application Selection (Power-up Settings)
mGGGGGGGGSGGGGGGGGG
GGGlGGOl}rPU
zGGGOGGG
GGzGGP
Press this button whenever there are any
changes in this section to update the
module settings
Select the Frequency band (2.4GHz or
5.2GHz or 5.8GHz) to operate after
Configuration
Select CU or MU mode
Step 8: Click [Config] button (upon every change) to configure the evaluation board.
22Pin Interface
wpuGJG wpuGuhtlG puVv|{G klzjypw{pvuG
XG }kkG wG pGwGaGZUZ}UG
YG nukG nG nukG
ZG tjsrG pG Y[U\]to¡GtGjGG
[G pup{phsG pVvG nwpv[G
\G tlzzhnlGylhkG pVvG nwpvZG
]G pYjzkhzs}G TG pYjGzsh}lOzkhPG
^G pYjzjszs}G TG pYjGzsh}lOzjsrPG
_G zkpvO|wspurGkh{hPG pVvG nwpvXYG
`G zkpvOkh{hYPG pVvG nwpv]G
XWG zkpvkh{hXPG pVvG nwpvXXG
XXG zkpv~kh{hWPG pVvG nwpv\G
XYG t|{lGpu{lyy|w{G pVvG nwpvYSGt|{lGpu{lyy|w{G
XZG ylzl{G TG ylzl{G
X[G ijrG pVvG nwpv_G
X\G nukG nG nukG
X]G syjrG pVvG nwpvXWG
X^G tvu{kG pVvG nwpvY[UGtvup{lypunG
X_G ylkslkG pVvG nwpvYZG
X`G i|slslkG pVvG nwpvXZG
YWG nukG nG nukG
YXG uUjG G uUjG
YYG uUjG G uUjG
FCC (Federal Communications Commission)
WARNING: This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual.
The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
This device complies with Part 15 of the FCC`s Rules. Operation is subject to
the following two Conditions:
1. This device may not cause harmful interference, and
2. This device must accept ant interference received,
including interference that may cause undesirable operation.
The antenna must be installed such that 20 cm is maintained between the antenna and users,
and the transmitter module may not be co-located with any other transmitter or antenna.
End users cannot modify this transmitter device. Any Unauthorized modification could void
the user`s authority to operate this device.
CE
Hereby, LG Electronics Inc. declares that this T2 is in compliance with the essential
requirements and other relevant provisions of directive 1999/5/EC.
Industry Canada(IC) Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
The host device must be labelled to display the Industry Canada certification number of the module.
Contains transmitter module IC: 2703H-T2
This equipment complies with IC radiation exposure limits for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20Cm between the user and the
radiating element of the device.
Note: The manufacturer is no responsible for any radio or TV interference caused by unauthorized
modifications to this
equipment. Such modification could void the user`s authority to operate the equipment.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est
soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil
doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais
fonctionnement de l'appareil.
Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du
module.
Contient module émetteur IC : 2703H-T2
Cet équipement est conforme aux limites IC exposition au rayonnement pour un environnement non
contrôlé.
Cet équipement doit être installé et utilisé avec distance minimum de 20cm entre l'utilisateur et l'élément
rayonnant de l'appareil.
Remarque: le fabricant n'est pas responsable des interférences radio ou télévision causé par des
modifications non
autorisées de cet équipement. Une telle modification pourrait annuler l'autorité de l 'utilisateur d'exploiter
cet équipement.
FCC Radio Frequency Interference Requirements
This device is restricted to ind oor use du e to its operation in th e 5 .15-5.25GHz fre quency rang
e. W e will n ot use this module in d evices that may be use d outdoo rs.
IC Radio Frequency Interference Requirements
Cet appareil est restreint à une utilisation intérieure en raison de son fon ctionnement dans la gamme
de fréquence de 5,15 5.25GHz. Nous n'allons pas utiliser ce module dans des appareils qui peuvent
être utilisés à l'extérieur.

Navigation menu