LG Electronics USA 9QK-TWFMK304D WLAN Module User Manual
LG Electronics USA WLAN Module
User manual
User Manual PRODUCT NAME : 1T2R Wi-Fi Module MODEL NAME TWFM-K304D The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. (00)-0073 User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 1 / 13 Table of Contents No. Description Page Features Module Photo Block Diagram Storage Conditions Operating Conditions Software Programming Pin Description Wi-Fi Certification Status Outline Drawing 10 10 Packing Information 11 ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 2 / 13 1. Features TWFM-K304D is the module for IEEE 802.11b/g/n wireless LAN. TWFM-K304D is based on MTK MT7601U solution. IEEE 802.11 b/g/n single band WLAN infrastructure Size : 45mm x 20mm x 8.2 mm Auto-calibration 1T2R mode with 150Mbps PHY rate USB 2.0 interface Supports drivers for Windows 7, Vista, XP, 2000 and Linux Security : WFA, WPA, WPA2, WPS2.0, WAPI Application : DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB 2. Module Photo Confidential ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 3 / 13 3. Block Diagram Confidential ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 REV.NO : 1.0 MODEL NAME : TWFM-K304D PAGE : 4 / 13 4. Storage Conditions Parameter Min Max Unit Storage Temperature -20 +80 ℃ Storage Humidity (@ 40℃) 90 Caution : The specifications above the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. • Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. 5. Operating Conditions Parameter Min Typ Max Unit Operating Temperature +55 ℃ Operating Humidity (40℃) 85 Supply Voltage 4.75 5.0 5.25 Vdc ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 5 / 13 6. Software Programming 1) Windows OS (1) Install a normal driver for winXP or win7. [Device Management] –[Network Adapter] – “802.11 USB Wireless..” The device description maybe is different by version. You can check whether it is proper or not by VID/PID. VID_148F&PID_7601< Fig. A.1 Device Information > (2) RUN WZC (Wireless Zero Configuration) [Computer Management] – [Service and Application] – [Service] The WZC service should be enabled < Fig. A.2 WZC > ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 6 / 13 (3) Run “Local Connection” 1) If WZC is enabled, you can scan available AP list as Please select AP by double-click. < Fig. A.3 AP list > 2) You can check the connection status by property box. < Fig. A.4 Connection Status > 2) Linux Device Driver Before compiling the driver, you should change make file or makefile.inc to meet your target platform. * Please refer to the release note in detail. ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV.NO : 1.0 MODEL NAME : TWFM-K304D REV. DATE : 2014.03.31 PAGE : 7 / 13 7. Pin Description Pin No. Pin Name I/O Pin Description VDD VDD 5.0V USB_DN I/O USB Communication signal USB_DN USB_DP I/O USB Communication signal USB_DP GND GND N/C < Bottom View > 1 5 < TOP View > Note. 1) Recommend a Module install sequence for prevent USB device failure - Supply 5.0V power - Connect to data signal (USB_DP, USB_DN) 2) Connector: 5Pin SMD Connector ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 8 / 13 8. Certification Status 1) FCC approval The satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product. Contains Transmitter module FCC ID: BEJ9QK-TWFMK304D This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiating element of this device and the user. This device must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators and following statements shall be included to host user manual: 1) The antenna must be installed such that 20cm is maintained between the antenna and users. 2) This module may not be co-located with any other transmitters or antennas. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements with this module installed. In the event that these conditions cannot be met, then the FCC authorizations are no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product including this module and obtaining separate FCC authorizations. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technical for help. ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D REV.NO : 1.0 PAGE : 9 / 13 This device complies with Part 15 of the FCC`s Rules. Operation is subject to the following two Conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesirable operation. This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. 2) IC approval This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris les interférences quipeuvent causer un mauvais fonctionnement de l'appareil. The host device must be labeled to display the Industry Canada certification number of the module. Contains transmitter module IC: 2703H-TWFMK304D Le dispositif d'accueil doivent être étiquetés pour afficher le numéro de certification d'Industrie Canada du module. Contient module émetteur IC : 2703H-TWFMK304D 3) CE approval Hereby, LG declares that this TWFM-K304D is compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. ©2014 LGIT. All rights reserved. User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D 9. Outline Drawing ©2014 LGIT. All rights reserved. REV.NO : 1.0 PAGE : 10 / 13 User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D 10. Packing Information ©2014 LGIT. All rights reserved. REV.NO : 1.0 PAGE : 11 / 13 User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D ©2014 LGIT. All rights reserved. REV.NO : 1.0 PAGE : 12 / 13 User Manual REG. DATE : 2014.03.31 REV. DATE : 2014.03.31 MODEL NAME : TWFM-K304D ©2014 LGIT. All rights reserved. REV.NO : 1.0 PAGE : 13 / 13
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No XMP Toolkit : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00 Format : application/pdf Creator : jhmoonb Title : Microsoft PowerPoint - 4-1TWFM-K304D_User Manual(영문)_Rev1 0 [호환 모드] Create Date : 2014:04:10 08:09:34Z Creator Tool : Microsoft PowerPoint - 4-1TWFM-K304D_User Manual(영문)_Rev1 0 [호환 모드] Modify Date : 2014:04:23 10:25:22+09:00 Metadata Date : 2014:04:23 10:25:22+09:00 Producer : doPDF Ver 6.2 Build 287 (Windows XP x32) Document ID : uuid:683ab99e-e6a4-4554-b92f-6bfeb5c853d7 Instance ID : uuid:bb080974-f116-487b-8e02-7ec3425444e3 Page Layout : OneColumn Page Mode : UseNone Page Count : 14 Author : jhmoonbEXIF Metadata provided by EXIF.tools