LG Electronics USA DT-NK PERSONAL COMPUTER User Manual 4E4B5FC7A5C1F62E717864

Download:
Mirror Download [FCC.gov]
Document ID	613215
Application ID	j1DQrMu82vjTJSzbRbdnaQ==
Document Description	USERS MANUAL 4
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	269.48kB (3368493 bits)
Date Submitted	2005-12-20 00:00:00
Date Available	2005-12-20 00:00:00
Creation Date	2005-12-20 13:58:27
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2005-12-20 13:58:36
Document Title	<4E4B5FC7A5C1F62E717864>
Document Creator	PScript5.dll Version 5.2.2
Document Author:	kjg1815

6-2. Main Board
The model name of the computer depends on the main board type. When extending the computer, check the model name on the label attached on the rear panel
of the computer and the following. Before extending the computer, check the main
board first.
Expansion slot (PCI-E x1)
Memory socket (DIMM)
Expansion slot (PCI)
Floppy disk connector
Expansion slot (PCI-E x16)
Hard disk/CD-ROM connector
CPU socket (with Pentium4 LGA 775)
Serial ATA-type hard disk connector
Note
The main board in your computer may look different from the picture.
System Expansion
69
6-3. Internal Connectors
Connectors are configured in a certain way at the factory, and connectors show the
connection status between the main board of the computer and peripherals.
(Connector configuration depends on product models.)
Before separating the connector, check the connection state of the connectors and leave a
record on the state.
Link the floppy disk driver connector and the hard disk/CD-ROM connector in the correct
direction.
The Pin Number and the color of the connector cable must match. Otherwise, an error may
occur in the computer.
Risk of explosin if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
There is a risk of explosion if the backup(standby) RTC battery is replaced by an incorrect
type. Dispose of used backup(stadby) RTC battery according to your local ordinances or
regulation.
70
System Expansion
Power on/off and power/hard disk
operation status indication lamp
connector (F_PANEL)
F_PANEL
Connects the power
on/off switch and the
power/hard disk operation
status indication lamp.
Power connector (ATX: 24 pins)
Connects the power
supply unit.
ATX
Optic drive connector (IDE : 40 pins)
CDROM, hard disk
driver.
Hard disk connector (S_ATA1,
S_ATA2, S_ATA3, S_ATA4: 7 pins)
S_ATA connector is
linked to the hard disk
driver.
S_ATA
Floppy disk driver connector
(FDD: 34 pins)
Connects the floppy disk
driver.
IDE
Power connector (ATX_12V: 4 pins)
Connects the power
supply unit.
ATX
1394 connector (F1_1394: 10 pins)
Connects camcorders
supporting IEEE1394.
FDD
USB connector (F_USB1, F_USB1:
10 pins)
Connects the front
USB.
F1_1394
SPDIF connector (SPDIF_LG: 3 pins)
Connects the SPDIF
port with optic output
feature.
USB
Audio connector (AZALIA_FP: 10
pins)
Connects a front earphone and microphone.
AZALIA_FP
CPU fan (CPU_FAN: 4 pins)
Provides power to the
CPU fan.
SPIF
System fan (SYSTEM_FAN: 3 pins)
Installed at the bottom
(rear panel) of the system,
and connects the VFD.
SYSTEM_FAN
VFD connector
Connects the VFD.
CPU_FAN
VFD
System Expansion
71
6-4 Replacing the CPU
To upgrade the CPU for better performance of the computer, you need to replace the
CPU first. Check the location and the type of the CPU in the main board, and do the
following. (Shape of the CPU FAN and CPU replacement methods may differ by
model.)
Unfasten four screws fixing the CPU fan as shown in the figure.
Align the groove to the right position,
pins can easily be broken.
Remove the CPU fan as shown in the figure.
Turn the CPU socket handle as shown in the figure of Step
as shown in the figure of Step .
72
System Expansion
, and open the cover
Lift the CPU up carefully to remove it from the main board.
Insert the new CPU with caution in the CPU socket in the correct direction and
close the cover
and then put down the handle of the CPU socket
Insert the CPU FAN as shown in the figure, and fix it with four screws.
Always wear gloves to avoid injuries.
System Expansion
73
6-5. Expanding the Computer Memory
You may expand the memory capacity, if needs be.
About Memory
This system uses a 240-pin memory module called Double Data Rate-2 (DDR-2),
not the old 184-pin memory module called Double Data Rate (DDR). The main
board can support maximum 2GB in memory.
Note
Windows 95, 98SE, and ME support maximum 512MB. Installing a memory with higher
capacity than 512MB may cause malfunctioning of the system.
Before Expanding the Memory
When disassembling the computer, wear gloves to protect internal parts of the
computer and slot cards from damage.
As the memory is sensitive to static electricity, be careful with the static electricity when removing or installing a memory.
Check the specifications of the current memory and the new memory before
expanding the memory.
Unlike SIMM, DIMM is of 64 bits. Therefore, single DIMM can function, and you
can add DIMM by one.
Note
When expanding the memory, add a memory with the same specification (DDR-2
SDRAM for 1.8V). (The shape of the memory may differ depending on the product
model.)
The DDR-2 memory provides greatly improved transmission rate than existing memories, and is differently shaped.
74
System Expansion
This computer supports PC3200/4300, DDR-2 specification.
When expanding the memory, use only unbuffered DDR SDRAM DMM
When inserting two same memories in same-colored DIMM slots, the computer will operate in Dual Channel mode.
FSB Frequency
Usable Memory
400/533 MHz
PC3200/4300-DDR-2 SDRAM 400/533MHz
Preparing a Memory
Before purchasing memory, study the specifications and features of the current
memory.
Specification : PC3200/4300 (240-pin DDR-2 SDRAM)
Rate
: 400MHz (200MHz
2), 533MHz (266MHz
2)
Type
: 256MB, 512MB
Composing the Memory
Refer to the following when expanding memory.
Total memory capacity
DIMM 1
DIMM 2
DIMM 3
DIMM 4
256 (One out of four slots)
256MB
256MB
SINGLE
DUAL
256MB
256MB
512MB
256MB
512 (One out of four slots)
256MB
1024MB
256MB
512MB
256MB
2048MB
512MB
512MB
512MB
DUAL
SINGLE
256MB
DUAL
DUAL
512MB
512MB
DUAL/SINGLE
512MB
DUAL
512MB
DUAL
Note
The computer operates faster in Dual Channel mode.
Use the same memory to operate the computer in Dual Channel mode.
It is recommended to use Dual Channel mode.
System Expansion
75
Replacing the Memory
Main board configuration, memory socket and memory type may differ by model.
Loosen the screws on the rear panel
of the computer, and remove the
cover.
Note
Before opening the computer cover,
turn off the power and all peripherals
connected to the computer. Disconnect
all power cables.
Release the latches from both flanks of the memory. The memory will be
removed automatically.
latch
Installing Memory
Lay the latches outwards from the
memory socket.
Note
When using a DDR-2 memory, the memory must be installed in each channel for
Dual Channel mode.
1-3 and 2-4 of dual Channels No. 1 ~ 4
Insert the memory (DIMM) vertically in
the socket in line with the grooves as
shown in the figure.
The memory will be automatically installed
even if not latched. However, it is recommended to fasten the latches until the
memory is completely fixed.
The memory will be automatically
installed even if not latched. However, it
is recommended to fasten the latches
until the memory is completely fixed
76
System Expansion
Checking the Expanded Memory
Turn on the power after installing the memory. Then, the computer will detect the
memory so that you don't need to change the system setup. The capacity of the
installed memory is checked as follows.
Connect the power cord and other cables, and turn on the computer and the monitor. Then, the initial screen to check the status of the computer will appear.
When the following screen appears, press [Esc] key. Then, POST screen will
appear.
On the next screen, press [Pause] to freeze the screen temporarily and to check
the Memory Testing : XXXXXX OK part.
Note
In the case that the logo screen is processed too fast to stop, press [Delete] key on the LG
logo screen. Then, select Advanced BIOS Features
Full Screen Logo Show
Selectable, and change status from Enabled to Disabled.
After checking the memory, press the [Esc] key. Windows screen will proceed.
System Expansion
77
6-6. Adding a Hard Disk
This computer supports up to four serial ATA controllers, and you can add one hard
disk drive.
Before Adding a Hard Disk
The following is when you purchase a hard disk and installs it, and describes the
most common case when you add a hard disk to a computer that is already equipped
with one hard disk.
Note
Write down the capacity, the cylinder count, the numbers of heads
and sectors of the hard disk marked on the upper part of the hard
disk. They are necessary for system setup (depending on the
product model.).
Adding a Hard Disk
Note
Power
connector
Prepare the hard disk to install.
The hard disk must be serial ATA type.
Signal
connector
When disassembling the computer, wear gloves to protect internal parts of the computer
and slot cards from damage.
Use screws compatible with specification when installing the hard disk in the main body.
Otherwise, critical damage may be done to electronic parts. For stable use of the hard
disk, fix the hard disk in the main body of the computer to prevent vibration.
78
System Expansion
Adding a hard disk drive
Refer to Opening the computer case (page 68) to remove the computer case
cover.
Remove 4 screws on the hard drive case and open the hard drive case as the
direction of the arrow.
Connect the power cable connector as shown
and the signal cable connector
as shown
to the new hard disk you want to replace in the hard disk case.
signal cable
power cable
Incorrect connection of the signal and
power cord may cause disfunction to the
computer or electrical shock.
System Expansion
79
Install a new hard disk (Slave hard) to add in the hard disk case and then fasten
three screws.
Note
Check the exact location of screws
when installing the hard disk
Right side
Fasten 4 screws after installing the hard disk drive as shown on the picture.
Refer to Closing the computer case (page 68) to close the computer case cover.
Note
You should setup and format your computer after
installing the hard disk. Refer to the Hard disk setup
(page81).
80
System Expansion
Hard disk drive setup
Turn on the computer and the monitor.
While the LG logo screen is on, press [Delete] key.
Then, the initial screen of System Setup menu will appear.
CMOS Setup Utility-Copyright(C)1984-2004 Award Software
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
PC Health Status
Frequency/Voltage Control
Load Optimized Defaults
Integrated Peripherals
Set Password
Power Management Setup
Save & Exit Setup
PnP/PCI Configurations
Exit Without Saving
Esc : Quit
F8: Q-Flash
: Select ltem
F10 : Save & Exit Setup
Virus Protection, Boot Sequence...
Execute the initial screen of the System Setup menu, and select Standard
CMOS Features by pressing
, and
keys. Then, press [Enter].
System Expansion
81
When the following appears, select IDE Channel 0 Salve by pressing
keys and press [Enter] key.
CMOS Setup Utility-Copyright(C)1984-2004 Award Software
Standard CMOS Features
Data (mm:dd:yy)
Time (hh:mm:ss)
IDE
Channel
0 Master
IDE
Channel
0 Slave
IDE Channel 1 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
Item Help
XXX, XXX, XXXX
XX, XX, XX
Memu Level
XXXXX
None
Select Your Boot
Device Priority
None
None
None
Halt On
All, But Keyboard.
Base Memory
Extended Memory
Total Memory
X.XX K
X.XX K
.XX K
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F7:Optimized Defaults
Press [Enter] key on IDE Channel 0 Slave to set it as Auto, and press [Enter]
key again on IDE HDD Auto-Detection to set it as Slave. Then, the additionally
installed hard disk will be automatically detected.
CMOS Setup Utility-Copyright(C)1984-2004 Award Software
IDE Channel 0 Slave
IDE HDD Auto-Detection
Press Enter
IDE Channel 0 Slave
Access Mode
Auto
Auto
Capacity
XXXXMB
Cylinder
Head
Precomp
Lauding Zome
Sector
Item Help
Menu Level
To auto-detect the
HDD's size, head...on
this channel
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values
F7:Optimized Defaults
To save changes in System Setup, press the [F10] key.
When the following message appears, press the [Enter] key to restart the computer.
82
System Expansion
Configuring the Hard Disk (in Factory Setting Status)
If you partition the hard disk using "diskmgmt.msc" existing data on the hard disk
driver will be deleted. You must carefully partition the hard disk when there is data on
the disk.
Select the [Start] button on the desk top, and click the [Execute].
Input diskmgmt.msc, and click [OK].
Select Added Disk 1 on Disk Management screen.
Right-click and select [New Loglcal Drive].
When New Partition Wizard screen appears, click the [Next] button.
System Expansion
83
When the partition type selection screen appears, select the main partition and
click the [Next] button.
Select the maximum size, and click the [Next] button.
You can use as much
space as you select in the
above window.
Select the Drive Letter and click the [Next] button.
84
System Expansion
When the partition format appears, set the file system, allocation unit, and volume label suitable for the User Environment and click the [Next] button.
The Partition Wizard has been completed. Click the [Finish] button.
After the completion, the additional hard disk will normally function.
System Expansion
85
6-7.Installing expansion cards
When you are using the computer, you may need to install expansion cards to
improve funtionality. The following instruction describes how to install expansion
cards.
Refer to Opening the computer case to open the computer case cover.
Remove the capas shown on the picture.
Remove 2 screws as shown on the picture.
Use the driver and remove the metal slot cover.
(Remove it, only when installing an additional extension card.)
Use proper tools (for example, drivers)
when removing metallic slot covers to
prevent hand injuries.
When disassembling the computer,
wear gloves to protect internal parts of
the computer and slot cards from damage.
86
System Expansion
Hold the expansion card with both hands and align the expansion card and slot.
Push down evenly to insert the card into the slot.
Expansion slot
Incorrect installation of an expansion
card may damage the main board
and result in a computer malfunction.
Fasten 2 screws after installing the extension slot.
Using the computer without closing
the case may result in fire, electric
shock, injury, and/or damage to the
computer.
Close the cap in the same position as you removed it.
Refer to Closing the computer case to close the case cover of the computer.
Install the driver program for the new expansion card.
System Expansion
87
88
MEMO
MEMO
89
90
MEMO
Product Specifications *
Specifications below differ depending on the models.
CPU
Supports Pentium4/ LGA775 2.8/3.0/3.2/3.4/3.6 GHz or higher (FSB:
533/800MHz)
System memory
128MB or higher. Differs depending on the model.
(This model allocates minimum 8MB or maximum 64MB as the
local video memory [frame buffer] using a built-in VGA.)
Cache memory
256KB/512KB or 1024KB L2 cache is equipped in the CPU.
Hard disk drive
40 GB or higher (Serial ATA type).
Keyboard
PS/2 keyboard (104keys)
Mouse
PS/2 mouse or USB (ball / wheel)
Video
Equipped in PCI-E 16x video card (one 15-pin connector) or in
the main board.
Sound
Equipped in the main board (MIC connector, speaker connector, line-in connector) and in the extension connector on the
rear part of the system.
USB
Equipped in the main board (four) and in the front (two).
Serial I/O
Installed in the main board. (one 9-pin connector).
Front I/O
Two USB ports and audio ports (SPEAKER-OUT and MIC-IN)
Parallel I/O
Extension slot
One printer port (25pins)
One PCI-E 16x slot, One PCI-E 1x slot, Two PCI slots.
Product size
Width 136 x Height 354 x depth 378(mm)
Power spec
100~127 / 200~240VAC, 5A / 4A, 50/60Hz or
200~240VAC. 4A, 50/60Hz
Environmental
requirement
Temperature:Average temperature:77 (25
Operating temperature:41 ~95 (5~35
Storage temperature:-4 ~131 -25~55
Humidity:Average humidity:60%(RH)
Operating humidity:30%~80%(RH)/Storage humidity:30%~80%(RH)
Product Specifications
91
NOTE
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radi-ate radio frequency energy and,
if not in-stalled and used in accordance with the in-structions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the fol-lowing measures:
-. Reorient or relocate the receiving antenna.
-. Increase the separation between the equip-ment and receiver.
-. Connect the equipment into an outlet on a circuit different from that to which the
re-ceiver is connected.
-. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
92
FCC

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
Linearized                      : No
Page Count                      : 24
PDF Version                     : 1.6
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:35501acd-706c-4933-baac-82fe182abcf6
Modify Date                     : 2005:12:20 13:58:36-05:00
Create Date                     : 2005:12:20 13:58:27-05:00
Metadata Date                   : 2005:12:20 13:58:36-05:00
Document ID                     : uuid:fbb8c446-2169-4a56-abf1-26aa66966b8d
Format                          : application/pdf
Title                           : <4E4B5FC7A5C1F62E717864>
Creator                         : PScript5.dll Version 5.2.2
Author                          : kjg1815
Producer                        : Acrobat Distiller 7.0.5 (Windows)

EXIF Metadata provided by EXIF.tools