LG Electronics USA E2280VV LED LCD MONITOR User Manual G User s manual

LG Electronics USA LED LCD MONITOR G User s manual

Users Manual

GOrder Number  : GETEC-C1-10-115  FCC Part 15 subpart BTest Report Number  : GETEC-E3-10-054  Page 1 / 1EUT Type: LED LCD Monitor FCC ID.: BEJE2280VVAPPENDIX G : USER’S MANUAL
OWNER’S MANUALLED LCD MONITOR LED LCD MONITOR MODELSE2280VE2380VE2280VXE2380VXwww.lg.comPlease read this manual carefully before operatingyour set and retain it for future reference.ENGLISH
1This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical  shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The appliance coupler is used as the disconnect device.Please make sure the device is installed near the wall outlet to which it isconnected and that the outlet is easily accessible.Operate the display only from a power source indicated in the specifications of thismanual or listed on the display. If you are not sure what type of power supply youhave in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call yourservice technician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display.  To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock. Important Precautions
2Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity.
Important Precautions3On CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water or otherliquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining.  On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.On Disposal The fluorescent lamp used in this product contains a small amount of mercury.Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
4Accessories!!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores to maintain standard compliance for the product.OWNER'S MANUAL/Cards Power Cord15-pin D-Sub Signal Cable(To set it up, this signal cable may beattached to  this product beforeshipping out.)DVI-D Signal Cable(This feature is not available inall countries.)AC-DC adapter
Connecting the Display5Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.Connecting the stand 1.Place the monitor face down on the cushion or soft cloth.3.Attach the monitor to the stand base by turning the screw to the right.4.Once assembled take the monitor up carefully and face the front side.2.Assemble the stand base into the standbody in the correct direction as shown in the picture. Stand BaseStand BodyScrew : Turn thescrew by using thescrew handle.
6Connecting the DisplayIMPORTANTThis illustration depicts the general model of connection. Your monitor may differ from the itemsshown in the picture.Do not carry the product upside down holding only the stand base. The product may fall and getdamaged or injure your foot.5.Turn the screw to the left to separate the stand bodyfrom the stand base. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. Positioning your displayAdjust the position of the panel in various ways for maximum comfort.Tilt Range : -5˚ to 10˚                   IMPORTANTIt is recommended that in order to maintain an ergonomic and comfortableviewing position, the forward tilt angle of the monitor should not exceed 5degrees.When adjusting the angle of the screen, do not put your finger(s) in betweenthe head of the monitor and the stand body. You can hurt your finger(s).
7Connecting the DisplayABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable Connect HDMI Cable1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.  2.Connect signal input cable         and power cord        in order, then tighten the screwof the signal cable. Connecting with the PC 12Wall-outlet typeORWall-outlet typeMac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin  2row connector.When using a D-Sub signal input cable connectorfor Macintosh NOTE  This is a simplified representation of the rear view.This rear view represents a general model; your display may differ from the view as shown.Varies according to model.CHeadphone/Earphone InputAV equipment(Set-Top Box, DVD, Video,Video Game Console)* HDMI is optimized on the AV equipment.* Not supported PCDVI-D (This feature is not available in all countries.)
8Connecting the DisplayNOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automaticallyadjusts the display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters,screen flicker or tilted screen while using the device or after changing screen resolution, pressthe AUTO function button to improve resolution. 3. Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function' is executed automatically.(Only Analog Mode)Power ButtonConnecting with the PC Power ButtonE2280V/E2380VE2280VX/E2380VX
9Control Panel FunctionsFront Panel ControlsSMART+ ButtonUse this button to enter ORIGINAL RATIO, FENGINE,DUAL WEB,CINEMA MODE menus.For more information, refer to page 22 to 30.MENU ButtonOSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time bypushing the MENU button for several seconds. Themessage "OSD UNLOCKED" should appear.E2280V/E2380VE2280VX/E2380VX
10Control Panel FunctionsAUTO ButtonAUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always pressthe AUTO button before entering the On ScreenDisplay(OSD). (Only Analog Mode)This will automatically adjust your display image tothe ideal settings for the current screen resolutionsize (display mode).The best display mode is1920 x 1080INPUT ButtonUse this button to turn the display on or off.From front view,the power indicator stays purple if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking purple. Power Button &Power IndicatorWhen two input signals at least are connected, you canselect the input signal (D-SUB/DVI/HDMI) you want.When only one signal is connected, it is automaticallydetected. The default setting is D-Sub. (SOURCE Hot key)Exit the OSD(On Screen Display).EXIT Button Use this button to select source from input. SUPER+ RESOLUTIONButtonFor more information, refer to page 31 to 34.E2280V / E2380V E2280VX / E2380VX
11On Screen Display (OSD) Control AdjustmentScreen AdjustmentMaking adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availableadjustments and selections you can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the discretionary Button, then the main menu of the OSD appears.To access a control, use the corresponding Buttons.Use the       /     Buttons to adjust the image to the desired level. Use the        Button to select other sub-menu items.Press the EXIT Button to exit from the OSD. 1234E2280V / E2380V
12On Screen Display (OSD) Control AdjustmentScreen AdjustmentMaking adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availableadjustments and selections you can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the discretionary Button, then the main menu of the OSD appears.To access a control, use the corresponding Buttons.Use the       /     Buttons to adjust the image to the desired level. Use the        Button to select other sub-menu items.Press the EXIT Button to exit from the OSD. 1234E2280VX / E2380VX
13LANGUAGE POWER INDICATORBUTTON INDICATORWHITE BALANCEFACTORY RESETTo customize the screen statusfor a user's operatingenvironmentOTHERSHORIZONTALVERTICALCLOCKPHASEOVERSCANDISPLAY To adjust the position of thescreen  COLOR TEMP GAMMACOLOR To customize the color of thescreenBRIGHTNESSCONTRASTSHARPNESSBLACK LEVELPICTURE To adjust the brightness,contrast and sharpness of thescreenTo improve the clarity andstability of the screen VOLUME To adjust the headphone/earphone volumeHDMIHDMIHDMIDVI-DHDMIDVI-DHDMIDVI-DHDMIDVI-DHDMIREDGREENBLUE(PRESET)                (USER)sRGB6500K 7500K8500K 9300KOn Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus.: D-SUB(Analog signal) input : DVI-D(Digital signal) input: HDMI signalMain menu Sub-menu            Supported inputDescriptionVOLUMEORIGINALRATIOF-ENGINEDUAL WEBCINEMA MODESMART+NORMALMOVIEINTERNETDEMOSTANDARDMOVIEGAMESPORTSDVI-DHDMIDVI-DDVI-DHDMITo select or customize desired image settingsWIDEORIGINALD-SUBDVI-DHDMID-SUBD-SUBD-SUBD-SUBD-SUBD-SUBD-SUBD-SUBD-SUBD-SUB
14On Screen Display(OSD) Selection and Adjustment NOTE The order of icons may differ depending on the model (13 to 34).SUPER+RESOLUTIONThe image is inevitably damagedduring the date processing toenlarge the image. SUPER+RESOLUTION can maintain theresolution to show the clear videoimage even with the enlargementwith the picture qualityimprovement technology thatadjusts the blurred focus andrough outline due to theenlargement.DVI-DHDMID-SUB
15On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitAdjust (Decrease/Increase)Select another sub-menuMove to the upper menuPress the MENU Button, then the main menu of the OSD appears.E2280V / E2380V
16On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitAdjust (Decrease/Increase)Select another sub-menuMove to the upper menuPress the MENU Button, then the main menu of the OSD appears.E2280VX / E2380VX
17On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionEXIT : Exit: Decrease: Increase: Select another sub-menu: Move to the upper menuBRIGHTNESSCONTRAST SHARPNESSBLACK LEVELTo adjust the brightness of thescreen. To adjust the contrast of the screen.To adjust the clearness of the screen.You can set the offset level. If youselect 'HIGH', the screen will be brightand if you select ‘LOW’, the screen willbe dark. (only for HDMI input)* Offset?As the criteria for video signal, it is thedarkest screen the monitor can show.D-SUB/DVI-D inputHDMI inputE2280V/E2380VD-SUB/DVI-D inputHDMI inputE2280VX/E2380VX
18On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionPRESETSelect the screen color. • sRGB: Set the screen color to fit thesRGB standard colorspecification.• 6500K-7500K: Red screen color. • 8500K-9300K: Blue screen color. REDSet your own red color levels.GREENSet your own green color levels.BLUESet your own blue color levels.GAMMA Set your own gamma value. : 0 / 1 / 2On the monitor, high gamma valuesdisplay whitish images and lowgamma values display blackishimages.COLOR TEMPUSERSelect either PRESET or USER toadjust the screen color. PRESET ModeUSER ModeE2280V/E2380VPRESET ModeUSER ModeE2280VX/E2380VXEXIT : Exit: Decrease: Increase: Select another sub-menu: Move to the upper menu
19On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionCLOCKPHASEOVERSCANTo minimize any vertical bars orstripes visible on the screenbackground.The horizontal screen size will alsochange.To adjust the focus of the display. This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters.Removes noise that may occur at theedges of an image when HDMI isconnected to an external device.  WhenON is selected, the image size isreduced to prevent noise. When OFF isselected, the original image size ismaintained regardless of noise. (Only for HDMI input)HORIZONTALVERTICALTo move image left and right.To move image up and down.D-SUB inputHDMI inputE2280V/E2380VD-SUB inputHDMI inputE2280VX/E2380VXEXIT : Exit: Decrease: Increase: Select another sub-menu: Move to the upper menu
20On Screen Display(OSD) Selection and Adjustment VOLUME To adjust the volume of headphone/Earphone.(Only for HDMI input)EXIT : Exit: Decrease: Increase: Mute: Move to the upper menuMain menu Sub menu DescriptionHDMI inputE2280V/E2380VHDMI inputE2280VX/E2380VX
21On Screen Display(OSD) Selection and Adjustment Press the      ,       buttons to resetimmediately.Main menu Sub menu DescriptionTo choose the language in which thecontrol names are displayed.LANGUAGEWHITEBALANCEIf the output of the video card isdifferent the required specifications,the color level may deteriorate dueto video signal distortion. Using thisfunction, the signal level is adjustedto fit into the standard output level ofthe video card in order to provide theoptimal image.Activate this function when whiteand black colors are present in thescreen.Restore all factory default settings except"LANGUAGE." FACTORYRESETPOWERINDICATORBUTTONINDICATORUse this function to set the powerindicator on the front side of the monitorto ON or OFF.If you set OFF, it will be turned off.If you set ON at any time, the powerindicator will automatically be turned on.Use this function to set the control keyindicator on the front side of the monitorto ON or OFF.If you set OFF, it will be turned off. If you set ON, it will be turned on.NOTE  If this does not improve the screen image, restore the factory default settings. If necessary, execute theWHITE BALANCE function again. This function will be enabled only when the input signal is an analogsignal. D-SUB inputHDMI/DVI-D inputE2280V/E2380VD-SUB inputHDMI/DVI-D inputE2280VX/E2380VXEXIT : Exit: Decrease: Increase: Select another sub-menu: Move to the upper menu
22On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitMoveSelect another sub-menuMove to the upper menuPress the SMART+ Button, then the main menu of the OSD appears.E2280V / E2380V
On Screen Display(OSD) Selection and Adjustment 23You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitMoveSelect another sub-menuMove to the upper menuPress the SMART+ Button, then the main menu of the OSD appears.E2280VX / E2380VX
24On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionChange the input image signal ratio tooriginal. WIDEORIGINALSwitch to full screen mode according toinput image signal.  D-SUB/DVI-D/HDMI inputE2280V/E2380VD-SUB/DVI-D/HDMI inputE2280VX/E2380VXEXIT : Exit,     : Move: Move to the upper menu
On Screen Display(OSD) Selection and Adjustment 25Main menu Sub menu DescriptionD-SUB/DVI-D inputHDMI inputSelect this when you want to use theproduct in the most general usingenvironment. Select this when you are watching avideo or movie.Select this when you want to use theoriginal standard video.* In the General (Standard) mode, theFENGINE is turned off.D-SUB/DVI-D inputHDMI inputE2280V/E2380VEXIT : Exit,     : Move: Move to the upper menuNORMALSTANDARDMOVIE
26On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionSelect this when you are working on thedocument (Word etc.)Select this when you are playing a game.This is used for advertising in the store. Thescreen will be divided to show the standardmode on the left and video mode on theright so that the consumers can check thedifference after applying the video mode. Select this when you watching generalsports.D-SUB/DVI-D inputHDMI inputD-SUB/DVI-D inputHDMI inputEXIT : Exit,     : Move: Move to the upper menuINTERNETGAMEDEMOSPORTS
On Screen Display(OSD) Selection and Adjustment 27Main menu Sub menu DescriptionD-SUB/DVI-D inputHDMI inputSelect this when you want to use theproduct in the most general usingenvironment. Select this when you are watching avideo or movie.Select this when you want to use theoriginal standard video.* In the General (Standard) mode, theFENGINE is turned off.D-SUB/DVI-D inputHDMI inputE2280VX/E2380VXEXIT : Exit,     : Move: Move to the upper menuNORMALSTANDARDMOVIE
28On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionSelect this when you are working on thedocument (Word etc.)Select this when you are playing a game.This is used for advertising in the store. Thescreen will be divided to show the standardmode on the left and video mode on theright so that the consumers can check thedifference after applying the video mode. Select this when you watching generalsports.D-SUB/DVI-D inputHDMI inputD-SUB/DVI-D inputHDMI inputEXIT : Exit,     : Move: Move to the upper menuINTERNETGAMEDEMOSPORTS
29On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionMake the eye comfortable by reducingthe  background brightness in the webpage.If select off, CINEMA MODE is off.* Before using below functions, please install Easy Set Packge programme.Help user to browse web efficiently bydividing in half.Help to arrange and move windows onscreen.Help user to control divided windowsratio.If select off, DUAL WEB is off.ONOFFONOFFD-SUB/DVI-D inputD-SUB/DVI-D inputE2280V/E2380VEXIT : Exit,     : Move: Move to the upper menu
30On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionMake the eye comfortable by reducingthe  background brightness in the webpage.If select off, CINEMA MODE is off.* Before using below functions, please install Easy Set Packge programme.Help user to browse web efficiently bydividing in half.Help to arrange and move windows onscreen.Help user to control divided windowsratio.If select off, DUAL WEB is off.ONOFFONOFFD-SUB/DVI-D inputD-SUB/DVI-D inputE2280VX/E2380VXEXIT : Exit,     : Move: Move to the upper menu
31On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameButtonTipExitMoveMove to the upper menuPress the SUPER+ RESOLUTION Button, then the main menu of the OSD appears.E2280V / E2380V
32On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using theOSD system. Listed below are the icons, icon names, and icon descriptions of theall items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameButtonTipExitMoveMove to the upper menuPress the SUPER+ RESOLUTION Button, then the main menu of the OSD appears.E2280VX / E2380VX
33On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionE2280V/E2380V* Noise may exist according to SR Mode, so enjoy the clear image by selecting SR Mode according to the Contents.EXIT : Exit,     : Move: Move to the upper menuSelect this when you want to use theproduct in the most general usingenvironment. In the General  mode, theSUPER+ RESOLUTION is turned off.When the user wants a natural videoscreen with soft image, it helps to get theoptimized screen. It is effective for videowith small movement or still image.When the user wants a comfortablevideo screen at the medium levelbetween low and high mode, it helps toget the optimized screen. It is effectivefor  UCC and SD level videos.When the user wants a sharp videoscreen with clear images, it helps to getthe optimized screen. It is effective forhigh resolution video screens andgames.The screen is divided to two, the leftscreen with original screen, and the rightscreen with SUPER+ RESOLUTIONmode, to compare the before and theafter the mode is applied.NORMALLOWMEDIUMHIGHDEMO
34On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionE2280VX/E2380VX* Noise may exist according to SR Mode, so enjoy the clear image by selecting SR Mode according to the Contents.EXIT : Exit,     : Move: Move to the upper menuSelect this when you want to use theproduct in the most general usingenvironment. In the General  mode, theSUPER+ RESOLUTION is turned off.When the user wants a natural videoscreen with soft image, it helps to get theoptimized screen. It is effective for videowith small movement or still image.When the user wants a comfortablevideo screen at the medium levelbetween low and high mode, it helps toget the optimized screen. It is effectivefor  UCC and SD level videos.When the user wants a sharp videoscreen with clear images, it helps to getthe optimized screen. It is effective forhigh resolution video screens andgames.The screen is divided to two, the leftscreen with original screen, and the rightscreen with SUPER+ RESOLUTIONmode, to compare the before and theafter the mode is applied.NORMALLOWMEDIUMHIGHDEMO
35TroubleshootingNo image appearsCheck the following before calling for service.No image appearsDo you see a "OSD LOCKED" message on the screen?●Is the power cord of thedisplay connected?●Is the power indicatorlight on?●Is the power indicatorflickering?●Do you see an "OUT OFRANGE" message onthe screen?●Do you see a "CHECKSIGNAL CABLE"message on thescreen?• Check and see if the power cord is connectedproperly to the power outlet.• Press the Power button.• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.• Try to turn on the PC.• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED” will appear.●Do you see “OSDLOCKED” when youpush MENU button?
36TroubleshootingDisplay image is incorrect●Display Position isincorrect.●On the screenbackground, verticalbars or stripes arevisible.●Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.• Press the AUTO button to automatically adjustyour display image to the ideal setting. If the results are unsatisfactory, adjust the imageposition using the H position and V position iconin the on screen display.• Press the AUTO button to automatically adjustyour display image to the ideal setting.If the results are unsatisfactory, decrease thevertical bars or stripes using the CLOCK icon inthe on screen display.• Press the AUTO button to automatically adjustyour display image to the ideal setting.If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(true color).IMPORTANTCheck Control Panel --> Display --> Settings and see if the frequency or the resolution were changed.If yes, readjust the video card to the recommend resolution.If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the screenmay be dimmed, truncated or biased. Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentionedabove may not be supported by the video card performance. In this case, please ask to thecomputer or the video card manufacturer.
37The Audio function is not workingTroubleshootingDisplay image is incorrect●The screen color ismono or abnormal.●The screen blinks.• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.• Make sure the video card is properly inserted inthe slot.• Set the color setting higher than 24 bits (true color)at Control Panel - Settings.• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.●Picture OK & No sound.• Check whether volume is "0".• Check sound muted.• HDMI cable installed properly.• Head phone cable installed properly.• Check sound format. Not supply to compressedsound format.Do you see an "Unrecognized monitor, Plug&Play (VESADDC) monitor found" message?●Have you installed thedisplay driver?• Be sure to install the display driver from the displaydriver CD (or diskette) that comes with yourdisplay. Or, you can also download the driver fromour web site: http://www.lg.com.• Make sure to check if the video card supportsPlug&Play function.
38Specifications                                                           E2280V54.686 cm (21.53 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.686cm0.248 mm x 0.248 mm (Pixel pitch)DisplaySync InputVideo InputMax VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 HzResolutionPlug&PlayOn Mode :24 W (Typ.)Sleep Mode ≤1 W Off Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandWidth    51.55 cm (20.30 inch) Height 42.65 cm (16.79 inch)     Depth 19.45 cm (  7.66 inch)Weight(excl. packing)  3.3 kg (7.28 lb)Dimensions& WeightTilt : -5˚ to 10˚Range12 V       2.0 APower InputAttached (     ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B (Analog, Digital, HDMI)Without StandWidth    51.55 cm (20.30 inch) Height 41.22 cm (16.23 inch)Depth 9.54 cm (  3.76 inch)NOTEInformation in this document is subject to change without notice.Type LCAP07F,manufactured by Lienchange ElectronicsAC-DC AdapterHorizontal Freq. Analog,Digital: 30 kHz to 83 kHz (Automatic)HDMI : 30 kHz to 83 kHz (Automatic)Vertical Freq. Analog,Digital : 56 Hz to 75 Hz (Automatic)HDMI : 56 Hz to 61 Hz (Automatic)Input Form Separate Sync., DigitalSignal Input 15 pin D-Sub ConnectorDVI-D connector (Digital)19 pin HDMI ConnectorInput Form Analog (0.7 Vp-p/ 75 ohm), Digital, HDMI
39Specifications                                                                  E2380V58.42 cm (23 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 58.42cm0.266 mm x 0.266 mm (Pixel pitch)DisplayHorizontal Freq. Analog,Digital: 30 kHz to 83 kHz (Automatic)HDMI : 30 kHz to 83 kHz (Automatic)Vertical Freq. Analog,Digital : 56 Hz to 75 Hz (Automatic)HDMI : 56 Hz to 61 Hz (Automatic)Input Form Separate Sync., DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI - D connector (Digital)19 pin HDMI ConnectorInput Form Analog (0.7 Vp-p/ 75 ohm), Digital, HDMIVideo InputMax VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 HzResolutionPlug&PlayOn Mode :28 W (Typ.)Sleep Mode ≤1 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandWidth    55.39 cm (21.81 inch) Height 44.84 cm (17.65 inch)   Depth 19.45 cm (  7.66 inch)Weight(excl. packing)  3.7 kg (8.16 lb)Dimensions& WeightTilt : -5˚ to 10˚Range12 V       2.2 APower InputAttached (     ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B (Analog, Digital, HDMI)Without StandWidth    55.39 cm (21.81 inch) Height 43.37 cm (17.07 inch)Depth 9.54 cm (  3.76 inch)NOTEInformation in this document is subject to change without notice.Type LCAP07F,manufactured by Lienchange ElectronicsAC-DC Adapter
42SpecificationsIndicatorOn ModeSleep ModeOff ModePurple (front view)Purple Blinking (front view) OffLED ColorMODEDisplay Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)* Recommend ModeDisplay Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)12345678480p576p720p720p1080i1080i1080p1080p31.5031.2537.5045.0028.1233.7556.2567.5060505060506050601234567891011*12720 x 400640 x 480640 x 480800 x 600800 x 6001024 x 7681024 x 7681152 x 8641280 x 10241280 x 10241680 x 10501920 x 108031.46831.46937.50037.87946.87548.36360.12367.50063.98179.97665.29067.500706075607560757560756060Preset Modes (Resolution) - D-sub(Analog) / DVI-D(Digital) INPUTHDMI Video InputVGAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAVESAE2280V/E2380V/E2280VX/E2380VX
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-saving guidelines issued by the U.S. Environmental Protection Agency(EPA).Make sure to read the Important Precautions before using the product.Keep the User’s Guide(CD) in an accessible place for furture reference.The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.MODELSERIAL
Regulatory Information cont. FCC Compliance StatementThis equipment has been tested and found to complywithin the limits of a Class B digital device pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation.This equipment generates, uses, and can radiate radiofrequency energy and if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radioor television reception (which can be determined byturning the equipment on and off), the user is encouragedto try to correct the interference by using one or more ofthe following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TVtechnician for help.Caution: Changes or modifications not expressly approvedby the party responsible for compliance could void theuser's (or your) authority to operate the equipment. Onlyperipherals (digital input/output devices, terminals, printers,etc.) certified to comply with the Class B limits may beattached to this monitor. Operation with non-certifiedperipherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used withthis System.Canadian DOC NoticeThis Class B digital apparatus meets all requirements ofthe Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe Brespecte toutes les exigences du Règlement sur lematériel brouilleur du Canada.CE Conformity Notice (for Europe)Products with the “CE” Marking comply with the EMCDirective(89/336/EEC) and LOW VOLTAGE Directive(73/23/EEC) issued by the Commission of the EuropeanCommunity.Compiance with these directives implies conformity to thefollowing European Norms :•  EN 55022 ; Radio Frequency Interference•  EN 55024 ; Electromagnetic Immunity•  EN 61000-3-2 ; Power Line Harmonics•  EN 61000-3-3 ; Voltage Fluctuations•  EN 60950-1 ; Product SafetyLow Radiation Compliance (MPR II)This monitor meets one of the strictest guidelines availabletoday for low radiation emissions, offering the user extrashielding and an antistatic screen coating. Theseguidelines, set forth by a government agency in Sweden,limit the amount of emission allowed in the Extremely LowFrequency (ELF) and Very Low Frequency (VLF)electromagnetic range.01NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.TCO'99 (TCO'99 applied model only)Congratulations!You have just purchased a TCO’99 approved and labelledproduct! Your choice has provided you with a productdeveloped for professional use. Your purchase has alsocontributed to reducing the burden on the environment andalso to the further development of environmentallyadapted electronics products.
Regulatory Information cont. 02Why do we have environmentally labelled computers?In many countries, environmental labelling has become anestablished method for encouraging the adaptation ofgoods and services to the environment. With the growingmanufacture and usage of electronic equipmentthroughout the world, there is a recognized concern for thematerials and substances used by electronic productswith regards to their eventual recycling and disposal. Byproper selection of these materials and substances, theimpact on the environment can be minimized.There are also other characteristics of a computer, such asenergy consumption levels, that are important from theviewpoints of both the work (internal) and natural (external)environments. Electronic equipment in offices is often leftrunning continuously, resulting in unnecessaryconsumption of large amounts of energy and additionalpower generation. From the standpoint of carbon dioxideemissions alone, it is vital to save energy.What does labelling involve?The product meets the requirements for the TCO’99scheme which provides for international and environmentallabelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of ProfessionalEmployees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) andStatens Energimyndighet (The Swedish NationalEnergy Administration).Approval requirements cover a wide range of issues:ecology, ergonomics, emission of electrical and magneticalfields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence anduse of heavy metals, brominated and chlorinated flameretardants, and other substances. The product must beprepared for recycling and the manufacturing site(s) shallbe certified according to ISO14001 or EMAS registered.Energy requirements include a demand that the systemunit and/or display, after a certain period of inactivity,shall reduce its power consumption to a lower level in oneor more stages. The length of time to reactivate the systemunit shall be reasonable for the user.Labelled products must meet strict environmentaldemands, for example, in respect of the reduction ofelectrical and magnetical fields as well as work load andvisual ergonomics.Below you will find a brief summary of the ecologicalrequirements met by this product. The completeecological criteria document can be found at TCODevelopment’s website http://www.tcodevelopment.comor may be ordered from:TCO DevelopmentSE-114 94 STOCKHOLM, SwedenFax: +46 8 782 92 07Email : development@tco.seInformation regarding TCO’99 approved and labelledproducts may also be obtained athttp://www.tcodevelopment.comEcological requirementsFlame retardantsFlame retardants may be present in printed wiring boardlaminates, cables, and housings. Their purpose is toprevent, or at least to delay the spread of fire. Up to 30%by weight of the plastic in a computer casing can consist offlame retardant substances. Many flame retardantscontain bromine or chlorine, and these flame retardantsare chemically related to PCBs (polychlorinatedbiphenyls). Both the flame retardants containing bromineor chlorine and the PCBs are suspected of giving rise tohealth effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*processes when not disposed of in accordance with strictstandards for disposal.TCO’99 requires that plastic components weighing morethan 25 grams shall not contain flame retardants withorganically bound bromine or chlorine. Flame retardantsare allowed in the printed wiring board laminates due tothe lack of commercially available alternatives.Cadmium**Cadmium is present in rechargeable batteries and in thecolour-generating layers of certain computer displays.TCO’99 requires that batteries, the colour-generatinglayers of display screens, and the electrical or electronicscomponents shall not contain any cadmium.Mercury**Mercury is sometimes found in batteries, relays andswitches. TCO’99 requires that batteries shall not containany mercury. It also demands that mercury is not presentin any of the electrical or electronics componentsassociated with the labelled unit. There is however one
Regulatory Information cont. 03exception. Mercury is, for the time being, permitted in theback light system of flat panel monitors as there today isno commercially available alternative. TCO aims onremoving this exception when a mercury free alternative isavailable.Lead**Lead can be found in picture tubes, display screens,solders and capacitors. TCO’99 permits the use of leaddue to the lack of commercially available alternatives, butin future requirements TCO Development aims atrestricting the use of lead._____________________________________________* Bio-accumulative is defined as substances which accumulate in living organisms.**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.TCO’03(TCO’03 applied model only)Congratulations!The display you have just purchased carries the TCO’03Displays label. This means that your display  is designed,manufacturedand tested according to some of the strictest quality andenvironmental requirements in the world. This makes for ahigh performance product, designed with the user in focusthat also minimizes the impact on our natural environment.Some of the features of the TCO’03 Display requirements:Ergonomics•     Good visual ergonomics and image quality in order toimprove the working environment for the user and toreduce sight and strain problems. Importantparameters are luminance, contrast, resolution,reflectance, colour rendition and image stability.Energy•     Energy-saving mode after a certain time – beneficialboth for the user and the environment•     Electrical safetyEmissions•     Electromagnetic fields•     Noise emissionsEcology•     The product must be prepared for recycling and themanufacturer must have a certified environmentalmanagement system such as EMAS or ISO 14 001•     Restrictions onchlorinated and brominated flame retardants andpolymersheavy metals such as cadmium, mercury and lead.The requirements included in this label have beendeveloped by TCO Development in co-operation withscientists, experts, users as well as manufacturers all overthe world. Since the end of the 1980s TCO has beeninvolved in influencing the development of IT equipment ina more user-friendly direction. Our labelling system startedwith displays in 1992 and is now requested by users andIT-manufacturers all over the world.For more information, please visitwww.tcodevelopment.comInformation for Environmental PreservationLGE. announced the 'LG Declaration for a CleanerEnvironment' in 1994, and this ideal has served as aguiding managerial principle ever since. The Declaration isa foundation that has allowed us to undertakeenvironmentally friendly activities in careful considerationof economic, environmental, and social aspects.We promote activities for environmental preservation, andwe specifically develop our products to embrace theconcept of environment-friendly. We minimize the hazardous materials contained in ourproducts. For example, there is no cadmium to be found inour monitors.Information for recyclingThis monitor may contain parts which could be hazardousto the environment. It is important that this monitor berecycled after use.LGE. handles all waste monitors through anenvironmentally acceptable recycling method. There areseveral take-back and recycling systems currently inEnglish
Regulatory Information cont. 04operation worldwide. Many parts will be reused andrecycled, while harmful substances and heavy metals aretreated by an environmentally friendly method.If you want to find out more information about ourrecycling program, please contact your local LG vendor ora corporate representative of LG. We set our vision and policies on a cleaner world byselecting the issue of the global environment as a task forcorporate improvement. Please visit our website for moreinformation about our ‘green’ policies.http://www.lge.com/about/environment/html/Recycling.jspInformationen zur Erhaltung der UmweltIm Jahr 1994 verkündete LGE die 'LG Declaration for aCleaner Environment' (LG Erklärung für eine sauberereUmwelt). Seitdem dient dieses Ideal als führendes Prinzipdes Unternehmens. Diese Erklärung war die Basis für dieDurchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche,umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden.Wir fördern Aktivitäten zum Schutz der Umwelt und dieEntwicklung unserer Produkte ist darauf ausgerichtet,unserem Konzept bezüglich Umweltfreundlichkeit gerechtzu werden. Wir sind darauf bedacht, den Anteil der in unserenProdukten enthaltenen schädlichen Materialien zuminimieren. So ist  in unseren Monitoren beispielsweisekein Kadmium zu finden.Informationen zum Thema RecyclingDieser Monitor enthält Teile, die umweltschädlich seinkönnen. Es ist unbedingt erforderlich, dass der Monitorrecycelt wird, nachdem er außer Dienst gestellt wurde.Bei LGE. werden alle ausrangierten Monitore in einemunter umweltbezogenen Aspekten geeigneten Verfahrenrecycelt. Augenblicklich sind weltweit mehrereRücknahme- und Recyclingsysteme im Einsatz. VieleTeile werden wieder verwendet und recycelt. SchädlicheSubstanzen und Schwermetalle werden durchumweltverträgliche Verfahren behandelt.Falls Sie mehr über unser Recyclingprogramm erfahrenmöchten, wenden Sie sich bitte an Ihren lokalen LG-Händler oder einen Unternehmensvertreter von LG. Wir richten unsere Firmenpolitik auf eine sauberereUmwelt hin aus, indem wir umweltspezifische Aspekte alswichtigen Punkt in die Weiterentwicklung unseresUnternehmens einfließen lassen. ZusätzlicheInformationen über unsere ‘grüne’ Firmenpolitik erhaltenSie auf unserer Website.http://www.lge.com/about/environment/html/Recycling.jspInformation sur la protection del’environnementLGE. a publié sa 'Déclaration en faveur d’unenvironnement plus propre' en 1994 et celle-ci est restée,depuis lors, un principe directeur de notre entreprise.Cette déclaration a servi de base à notre réflexion et nousa permis de prendre en compte à la fois les aspectséconomiques et sociaux de nos activités, tout enrespectant l’environnement.Nous encourageons les activités en faveur de lapréservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons auminimum les matières dangereuses qui entrent dans leurcomposition et l’on ne trouve pas de cadmium, parexemple, dans nos moniteurs.Information sur le recyclageCe moniteur peut contenir des composants qui présententun risque pour l’environnement. Il est donc important quecelui-ci soit recyclé après usage.LGE. traite les moniteurs en fin de cycle conformément àune méthode de recyclage respectueuse del’environnement. Nous reprenons nos produits et lesrecyclons dans plusieurs sites répartis dans le mondeentier. De nombreux composants sont réutilisés etrecyclés, et les matières dangereuses, ainsi que lesmétaux lourds, sont traités selon un procédé écologique.Si vous souhaitez plus de renseignements sur notreprogramme de recyclage, veuillez contacter votrerevendeur LG ou un l’un de nos représentants. Nous voulons agir pour un monde plus propre et croyonsau rôle de notre entreprise dans l’amélioration del’environnement. Pour plus de renseignements sur notrepolitique “verte”, rendez visite à notre site :http://www.lge.com/about/environment/html/Recycling.jspDeutschFrançais
05Regulatory Information cont. Informazioni per la tutela dell’ambienteLa LGE. ha annunciato nel 1994 la cosiddetta 'LGDeclaration for a Cleaner Environment' (Dichiarazione diLG a favore di un ambiente più pulito), un ideale che daallora funge da principio ispiratore della gestioneaziendale. La dichiarazione rappresenta il fondamento checonsente di intraprendere attività a favore dell'ambientetenendo conto degli aspetti economici, ambientali esociali.Noi della LG, promuoviamo attività a favore dellatutela dell'ambiente sviluppando appositamente i nostriprodotti per cogliere il concetto del rispetto dell’ambienteriducendo i materiali dannosi presenti nei nostri prodotti.Ad esempio nei nostri monitor non è presente il cadmio.Informazioni per il riciclaggioIl monitor può presentare componenti che potrebberorisultare eventualmente dannosi per l'ambiente. Èimportante che il monitor sia riciclato al termine del suoutilizzo.La LGE. gestisce tutti i monitor di rifiuto con un metodo diriciclaggio soddisfacente dal punto di vista ambientale. Intutto il mondo sono attualmente in funzione numerosisistemi di riciclaggio e recupero. I diversi componenti sonoriutilizzati e riciclati, mentre le sostanze dannose e i metallipesanti vengono trattati con un metodo rispettosodell’ambiente.Se si desiderano maggiori informazioni in merito alprogramma di riciclaggio, è consigliabile rivolgersi alproprio rivenditore LG o ad un rappresentante aziendaledella LG. Noi della LG impostiamo la nostra visione e le nostrepolitiche a favore di un mondo più pulito ponendo laquestione dell'ambiente dal punto di vista globale comeuna mansione rivolta al miglioramento della nostraazienda. Vi invitiamo a visitare il nostro sito internet perulteriori informazioni sulla nostra politica “verde”.http://www.lge.com/about/environment/html/Recycling.jspInformación para la conservación medioambientalLGE. presentó la 'Declaración para un entorno más limpiode LG' en 1994 y este ideal ha servido para guiar nuestrosprincipios empresariales desde entonces. La Declaraciónes la base que nos ha permitido llevar a cabo tareas querespetan el medio ambiente siempre teniendo en cuentaaspectos sociales, económicos y medioambientales.Promocionamos actividades orientadas a la conservacióndel medio ambiente y desarrollamos nuestros productosespecíficamente para que se ajusten a la filosofía queprotege el entorno. Reducimos al máximo el uso de materiales de riesgo ennuestros productos. Un ejemplo de ello es la ausenciatotal de cadmio en nuestros monitores.Información para el reciclajeEste monitor puede contener piezas que entrañen riesgosmedioambientales. Es importante reciclar este monitordespués de su utilización.LGE. trata todos los monitores usados siguiendo unmétodo de reciclaje que no daña al entorno. Contamoscon diversos sistemas de recuperación y reciclaje quefuncionan a nivel mundial en la actualidad. Es posiblereciclar y reutilizar muchas de las piezas, mientras que lassustancias dañinas y los metales pesados se tratansiguiendo un método que no perjudique al medioambiente. Si desea obtener más información acerca delprograma de reciclaje, póngase en contacto con suproveedor local de LG o con un representante empresarialde nuestra marca. Basamos nuestra visión y nuestras políticas en un mundomás limpio y para ellos optamos por un entorno globalcomo tarea principal de nuestra evolución como empresa.Visite nuestra página Web para obtener más informaciónsobre nuestras políticas ecológicas.http://www.lge.com/about/environment/html/Recycling.jspInformações relacionadas à preservaçãoambientalA LGE. anunciou a 'LG Declaration for a CleanerEnvironment' (Declaração da LG para um ambiente maislimpo) em 1994 e esse ideal tem servido desde entãocomo um princípio administrativo de orientação. ADeclaração é a base que nos tem permitido realizaratividades favoráveis ao ambiente com consideraçãoatenta aos aspectos econômicos, ambientais e sociais.Promovemos atividades de preservação ambiental edesenvolvemos nossos produtos para englobarItalianoEspanõlPortuguês
06Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossosprodutos. Por exemplo, não há cádmio em nossosmonitores.Informações relacionadas à reciclagemEste monitor pode conter peças que podem representarriscos ao ambiente. É importante que ele seja recicladoapós o uso.A LGE. cuida de todos os monitores descartados atravésde um método de reciclagem agradável ao ambiente. Hávários sistemas de devolução e reciclagem atualmenteem operação no mundo. Muitas peças serão reutilizadase recicladas e as substâncias nocivas e os metaispesados passarão por tratamento através de um métodofavorável ao ambiente.Para obter mais informações sobre nosso programa dereciclagem, entre em contato com seu fornecedor LGlocal ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas aum mundo mais limpo selecionando a questão doambiente global como uma tarefa de aprimoramentocorporativo. Visite nosso site para obter mais informaçõessobre nossas políticas de meio ambiente.http://www.lge.com/about/environment/html/Recycling.jspInformatie met betrekking tot het behoud vanhet milieuLGE. publiceerde in 1994 de 'LG Declaration for a CleanerEnvironment' (de LG-verklaring met betrekking tot eenschoner milieu). Deze verklaring en het ideaal van eenschoner milieu fungeren sindsdien als een bestuurlijkeleidraad voor onze onderneming. Op basis van dezeverklaring ontplooien wij milieuvriendelijke activiteiten,waarbij er zowel met sociale en economische aspecten,als met milieuaspecten zorgvuldig rekening wordtgehouden.Wij ondersteunen activiteiten die zijn gericht op hetbehoud van het milieu en wij houden bij het ontwikkelenonze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen inonze producten. Er wordt bijvoorbeeld geen cadmiumverwerkt in onze monitors.NederlandsInformatie met betrekking tot recyclingDeze monitor bevat materialen die schadelijk zoudenkunnen zijn voor het milieu. Het is belangrijk dat dezemonitor aan het einde van zijn levensduur wordtgerecycled.LGE. verwerkt alle afvalmonitors via een milieuvriendelijkerecyclingmethode. Hiervoor worden er momenteelwereldwijd verscheidene inname- en recyclingsystemengehanteerd. Een groot aantal onderdelen wordt opnieuwgebruikt en gerecycled, waarbij schadelijke stoffen enzware metalen volgens een milieuvriendelijke methodeworden verwerkt.Voor meer informatie over ons recyclingprogramma kunt ucontact opnemen met uw plaatselijke LG-vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonerewereld vloeien voort uit het feit dat wij het milieu hebbenaangemerkt als een onderwerp dat speciale aandachtverdient binnen onze onderneming. Bezoek onze websitevoor meer informatie over ons 'groene' beleid.http://www.lge.com/about/environment/html/Recycling.jsp»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚',ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎËÔ‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘Ë ·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓωÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ ËÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï.Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡ÌÂÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌËÂ‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË ÒÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË. Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯ËıÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ.»ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚,ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â.Russian
07Regulatory Information cont. EPA(EPA applied model only)ENERGY STARis a set of power-saving guidelinesissued by the U.S. Environmental ProtectionAgency(EPA).NOM MARK (Mexico only)ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂËÒÔÓθÁÓ‚‡Ìˡ.KÓÔÓ‡ˆËˇ LGE ÔÂÂ‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ÂÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„ÓÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍËÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.«‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ ÍÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ ÍÓÔÓ‡ˆËË LG. Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛Ó ̇¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ:http://www.lge.com/about/environment/html/Recycling.jspAs an ENERGY STAR Partner LGE U. S.A.,Inc. has determined that this productmeets the ENERGY STAR guidelines forenergy efficiency.
08Regulatory Information cont. 1.When this crossed-out wheeled bin symbol is attachedto a product it means the product is covered by theEuropean Directive 2002/96/EC. 2.All electrical and electronic products should bedisposed of separately from the municipal wastestream via designated collection facilities appointed bythe government or the local authorities. 3.The correct disposal of your old appliance will helpprevent potential negative consequences for theenvironment and human health.4.For more detailed information about disposal of yourold appliance, please contact your city office, wastedisposal service or the shop where you purchased theproduct.Disposal of your old appliance1.Quando su un prodotto è riportato il simbolo di1.När den här symbolen med en överkryssadsoptunna på hjul sitter på en produkt innebär detatt den regleras av European Directive2002/96/EC.2.Alla elektriska och elektroniska produkter börkasseras via andra vägar än de som finns förhushållsavfall, helst via för ändamålet avseddauppsamlingsanläggningar som myndigheternautser.3.Om du kasserar din gamla apparat på rätt sättså bidrar du till att förhindra negativakonsekvenser för miljön och människors hälsa.4.Mer detaljerad information om kassering av dingamla apparat kan får av kommunen,renhållningsverket eller den butik där du köpteprodukten.1.Als het symbool met de doorgekruiste verrijdbareafvalbak op een product staat, betekent dit dathet product valt onder de Europese Richtlijn2002/96/EC.2.Elektrische en elektronische producten mogenniet worden meegegeven met het huishoudelijkafval, maar moeten worden ingeleverd bijspeciale inzamelingspunten die door de lokale oflandelijke overheid zijn aangewezen.3.De correcte verwijdering van uw oude toestelhelpt negatieve gevolgen voor het milieu en demenselijke gezondheid voorkomen.Smaltimento delle apparecchiature obsoleteKassering av din gamla apparatUw oude toestel wegdoen1.Ce symbole, représentant une poubelle surroulettes barrée d'une croix, signifie que leproduit est couvert par la directive européenne2002/96/EC.2.Les éléments électriques et électroniquesdoivent être jetés séparément, dans les vide-ordures prévus à cet effet par votre municipalité. 3.Une élimination conforme aux instructions aideraà réduire les conséquences négatives et risqueséventuels pour l'environnement et la santéhumaine.4.Pour plus d'information concernant l'éliminationde votre ancien appareil, veuillez contacter votremairie, le service des ordures ménagères ouencore la magasin où vous avez acheté ceproduit.Élimination de votre ancien appareilun bidone della spazzatura barrato da una crocesignifica che il prodotto è coperto dalla direttivaeuropea 2002/96/EC.2.Tutti i prodotti elettrici ed elettronici dovrebberoessere smaltiti separatamente rispetto allaraccolta differenziata municipale, medianteimpianti di raccolta specifici designati dalgoverno o dalle autorità locali.3.Il corretto smaltimento delle apparecchiatureobsolete contribuisce a prevenire possibiliconseguenze negative sulla salute umana esull'ambiente.4.Per informazioni più dettagliate sullo smaltimentodelle apparecchiature obsolete, contattare ilcomune, il servizio di smaltimento rifiuti o ilnegozio in cui è stato acquistato il prodotto. EnglishFrenchItalianSwedishDutchWEEE (for Europe )
Regulatory Information cont. 091.Wenn dieses Symbol eines durchgestrichenenAbfalleimers auf einem Produkt angebracht ist,unterliegt dieses Produkt der europäischenRichtlinie 2002/96/EC.2.Alle Elektro- und Elektronik-Altgeräte müssengetrennt vom Hausmüll  über dafür staatlichvorgesehenen Stellen entsorgt werden.3.Mit der ordnungsgemäßen Entsorgung des altenGeräts vermeiden Sie Umweltschäden und eineGefährdung der persönlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des altenGeräts erhalten Sie bei der Stadtverwaltung,beim Entsorgungsamt oder in dem Geschäft, woSie das Produkt erworben haben. 1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓηχÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK.2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿  ·fi Ù· ÁÂÓÈοÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈṲ̂ӈÓÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘÙÔÈΤ˜ ·Ú¯¤˜.3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı·‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘.4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ ÌÂÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·Ù ÙÔÚÔ˚fiÓ.1.Tämä merkki tuotteessa tarkoittaa, että tuotekuuluu sähkö- ja elektroniikkalaiteromustaannetun EU-direktiivin 2002/96/EYsoveltamisalaan.2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseenkeräyspisteeseen.3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin,kierrätyskeskukseen tai myymälään, josta ostit laitteen.1.Når der er et tegn med et kryds over enskraldespand, betyder det, at produktet eromfattet af EU-direktiv 2002/96/EC.2.Alle elektriske og elektroniske produkter skalsmides ud et andet sted end gennem denkommunale affaldsordning ved hjælp af specielleindsamlingsfaciliteter, der er organiseret af staten1.Si en un producto aparece el símbolo de un contenedorde basura tachado, significa que éste se acoge a laDirectiva 2002/96/CE.2.Todos los aparatos eléctricos o electrónicos se debendesechar de forma distinta del servicio municipal derecogida de basura, a través de puntos de recogidadesignados por el gobierno o las autoridades locales.3.La correcta recogida y tratamiento de los dispositivosinservibles contribuye a evitar riesgos potenciales para elmedio ambiente y la salud pública.4.Para obtener más información sobre cómo deshacerse desus aparatos eléctricos y electrónicos viejos, póngase encontacto con su ayuntamiento, el servicio de recogida debasuras o el establecimiento donde adquirió el producto. Vanhojen laitteiden hävittäminenEntsorgung von AltgerätenSådan smider du dit gamle apparat ud∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜Cómo deshacerse de aparatos eléctricos yelectrónicos viejoseller de lokale myndigheder.3.Korrekt bortskaffelse af dit gamle apparat er medtil at forhindre mulige skadevirkninger på miljøetog menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse afdit gamle apparat kan fås ved at kontakte ditlokale kommunekontor, renovationsselskab ellerden butik, hvor du købte produktet. FinnishGermanDanishGreekSpanish4.Wilt u meer informatie over de verwijdering vanuw oude toestel? Neem dan contact op met uwgemeente, de afvalophaaldienst of de winkelwaar u het product hebt gekocht.
Regulatory Information cont. 10                        PortugueseSlovakCzechCroatianHungarianPolish
                  Regulatory Information cont. 11EstonianLatvianLithuanian

Navigation menu