LG Electronics USA E2350TV LCD MONITOR. User Manual W19 2243S T ENG

LG Electronics USA LCD MONITOR. W19 2243S T ENG

Users Manual

Make sure to read the Important Precautions before using theproduct. Keep the User's Guide(CD) in an accessible place for futurereference.See the label attached on the product and give the information toyour dealer when you ask for service.User’s GuideE2050SE2050TE2250TE2350TE2250SE2350S
1This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The power supply cord is used as the main disconnection device. Ensure that thesocket-outlet is easily accessible after installation.Operate the display only from a power source indicated in the specifications ofthis manual or listed on the display. If you are not sure what type of power supplyyou have in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call your servicetechnician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display.To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock. Important Precautions
Important PrecautionsNOTETHE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTRERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY NOTEThis epuipment has been tested and found to comply with the limits for a class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequencycause harmful interference to radio communications.However,there is noguarantee that interference will not occur in a particular installation.If this which can be determined by turning the equipment off and on,the user isencouraged to try to correct the interference by one or more of the followingmeasures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and the receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.energy and,if not installed and used in accordance with the instructions,may equipment does cause harmful interference to radio or television reception,TO OPERATE THE EQUIPMENT. -Consult the dealer or an experienced radio/TV technician for help.A3
2Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not placethe display where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchensink, laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity.
Important Precautions3On CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water orother liquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining.On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.
4Accessories!!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.User's Guide/Cards15-pin D-Sub Signal Cable(To set it up, this signal cable maybe attached to this product beforeshipping out.)NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores to maintain standard compliance for the product.AC-DC adapter(Depending on the country)orAC-DC adapterPower Cord(Depending on the country)DVI-D Signal Cable(This feature is not availablein all countries.)
Connecting the Display5Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.1 way stand 1. Place the monitor with its front facing downward on a cushion or soft cloth.ImportantThis illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Once you connect the stand base, try not to disconnect it.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot.2. Use a coin on the back of the stand base and turn the screw clockwise to tighten.4. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise..Once assembled take the monitor up carefully and face the front side.3
Connecting the Display6Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.2 way stand 1. Place the monitor with its front facing downward on a cushion or soft cloth.ImportantThis illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Once you connect the stand base, try not to disconnect it.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot.2.Press the botton as shown, and the stand body..Once pull the stand body up,take the monitor up carefully and face the front side.3
Connecting the DisplayAfter installation, adjust the angle as shown below. Adjust the position of the panel in various ways for maximum comfort.Tilt Range : -5˚~15˚ ERGONOMICIt is recommended that in order to maintain an ergonomic and comfortable viewing position,the forward tilt angle of the monitor should not exceed 5 degrees.15-5 Do not touch or press the screen whenadjusting the angle of the monitor. When adjusting the angle of the screen, donot put your finger(s) in between the head ofthe monitor and the stand body. You canhurt your finger(s).7* With sandbase Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Positioning your display
ErgonomicIt is recommended that in order to maintain an ergonomic and comfortable viewingposition, the backward tilt angle of the monitor should exceed 10 degrees.A68Connecting the Display* Without sandbase 20Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Positioning your display
Connecting the DisplayNOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters,screen flicker or tilted screen while using the device or after changing screen resolution, pressthe AUTO/SET function button to improve resolution. AConnect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. 2.Connect signal input cable and power cord in order, then tighten the screwof the signal cable. Connecting with the PC 123. Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function' is executed automatically.E2050S/E2250S/E2350S9DC-IN D-SUBPCAORMac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin 2row connector.When using a D-Sub signal input cable connectorfor Macintosh NOTEThis is a simplified representation of the rear view.This rear view represents a general model; your display may differfrom the view as shown. Wall-outlet typeWall-outlet typePower Button
Connecting the DisplayNOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters,screen flicker or tilted screen while using the device or after changing screen resolution, pressthe AUTO/SET function button to improve resolution. ABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. 2.Connect signal input cable and power cord in order, then tighten the screwof the signal cable. Connecting with the PC 123. Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function' is executed automatically.(Only Analog Mode)E2050T/E2250T/E2350T10DC-IN D-SUBDVI-DPCPCAMac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin 2row connector.When using a D-Sub signal input cable connectorfor Macintosh NOTEThis is a simplified representation of the rear view.This rear view represents a general model; your display may differfrom the view as shown. Wall-outlet typeWall-outlet typePower ButtonOR
Control Panel FunctionsFront Panel ControlsMENU ButtonUse this button to enter or exit the On Screen Display.OSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time by pushingthe MENU button for several seconds. The message"OSD UNLOCKED" should appear.1 2 35 6 7 8411For more information, refer to page 23.ENGINE Button NORMAL MOVIE I NTERNET DEMOEXITENGINE ButtonUse this button to enter AUTO BRIGHT,ORIGINAL RATIO,IMAGE BOOSTER,DUAL WEB,CINEMA MODE menus.For more information, refer to page 20~21.SMART+
Control Panel FunctionsUse this button to enter a selection in the On Screen Display.AUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always pressthe AUTO button before entering the On ScreenDisplay(OSD). (Only Analog Mode)This will automatically adjust your display image tothe ideal settings for the current screen resolutionsize (display mode).The best display mode isE2050S/E2050T : 1600 x 900AUTO ButtonINPUT Button(SOURCE Hot key)When two input signals are connected, you can select theinput signal (D-SUB/DVI) you want. When only one signalis connected, it is automatically detected. The defaultsetting is D-Sub. (Only E2050T/E2250T/E2350T )EXIT ButtonUse these buttons to exit the On Screen Display.Power Button &Use this button to turn the display on or off.Power IndicatorThe power indicator stays white if the display is runningproperly (On Mode). If the display is in Sleep Mode(Energy Saving), the power indicator is blinking white 12This is lens for light sensor sletect outside luminance,when setting AUTO BRIGHT ON.Light sensorUse this button to enter a selection in the On Screen Display.E2250S/E2250T : 1920 x 1080E2350S/E2350T : 1920 x 1080
On Screen Display (OSD) Control AdjustmentScreen AdjustmentMaking adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availableadjustments and selections you can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the discretionary Button , then the main menu of the OSD appears.To access a control, use the corresponding Buttons.Use the / Buttons to adjust the image to the desired level. Use the Button to select other sub-menu items. EXIT Button to exit from the OSD .1234MONITOR SETUPMENU ENGINE AUTOSMART+ INPUT EXITMENU PICTUREBRIGHTNESS 100CONTRAST 70SHARPNESS 5EXITMONITOR SETUPAUTOMENU ENGINE AUTOSMART INPUT EXITAUTO13Press the
NOTEThe order of icons may differ depending on the model (14~24).HDMILANGUAGEWHBUTTON INDICATORITE BALANCEPOWER INDICATORFACTORY RESETTo customize the screen statusfor a user's operatingenvironmentOTHERSDSUBDVI-DHORIZONTALVERTICALCLOCKPHASETo improve the clarity andstability of the screen DISPLAY To adjust the position of thescreen(PRESET / USER) GAMMACOLOR TEMPCOLOR To customize the color of thescreenBRIGHTNESSCONTRASTSHARPNESS PICTURE To adjust the brightness, contrastand sharpness of the screenDSUBDVI-DDSUBDVI-DDSUBDSUBMain menu Sub-menuSupported inputDescription: D-SUB(Analog signal) input : DVI-D(Digital signal) inputDSUBDVI-DF-ENGINENORMAL DSUBTo select or customize desiredMOVIE DVI-Dimage settingsINTERNETDEMOAUTO BRIGHT DSUBTo adjust the image sizeSMART+DVI-DORIGINAL RATIOIMAGE BOOSTERDUAL WEBCINEMA MODEOn Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus.DSUBDVI-D
15EXIT : Exit: Adjust (Decrease/Increase) : Select another sub-menu : Restart to select sub-menuEXITMENU PICTUREBRIGHTNESS100CONTRAST70SHARPNESS5MONITOR SETUPAUTOMENU ENGINE AUTOSMART+ INPUT EXITMONITOR SETUPAUTOMENU ENGINE AUTOSMART INPUT EXITPress the MENU Button, then the main menu of the OSD appears.Press the MENU Button, then the main menu of the OSD appears.On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.NOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.IconsMenu NameSub-menusButtonTip
16On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionExit : Exit: Decrease: Increase: Select another sub-menuBRIGHTNESSCONTRAST To adjust the brightness of the screen. To adjust the contrast of the screen.PRESETREDGREENBLUESelect the screen color. • sRGB: Set the screen color to fit thesRGB standard colorspecification.• 6500K: Slightly reddish white.• 9300K: Slightly bluish white.Set your own red color levels.Set your own green color levels.Set your own blue color levels.SHARPNESS To adjust the clearness of the screen. Exit : Exit: Decrease: Increase: Select another sub-menu USERCOLOR TEMPGAMMA Set your own gamma value. : 0 / 1/ 2On the monitor, high gamma valuesdisplay whitish images and low gammavalues display blackish images.MENU PICTURECONTRAST 70SHARPNESS 5EXITBRIGHTNESS 100PICTUREMENU COLORGAMMA 1K0056TESERPGREEN 50RED 50BLUE 50GAMMACOLOR TEMP PRESETEXITCOLOR
17On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionCLOCKPHASETo minimize any vertical bars orstripes visible on the screenbackground.The horizontal screen size will alsochange.To adjust the focus of the display. This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters.HORIZONTALVERTICALTo move image left and right.To move image up and down.Exit : Exit: Decrease: Increase: Select another sub-menu E2050SMENU DISPLAYHORIZONTAL 50VERTICAL 50CLOCK 50PHASE 50DSUB 1024X768 60HzEXITEXITDISPLAYMENU DISPLAYVERTICAL 50CLOCK 50PHASE 501024X768 60HzHORIZONTAL 50HORIZONTALE2050T/W2250T/W2350T
18On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionTo choose the language in which thecontrol names are displayed.LANGUAGEWHITEBALANCEIf the output of the video card isdifferent the required specifications,the color level may deteriorate dueto video signal distortion. Using thisfunction, the signal level is adjustedto fit into the standard output level ofthe video card in order to provide theoptimal image.Activate this function when whiteand black colors are present in thescreen.FACTORYRestore all factory default settings exceptRESET"LANGUAGE." Press the , buttons to reset immediately.POWERINDICATORUse this function to set the powerindicator on the front side of the monitorto ON or OFF.If you set OFF, it will go off. If you set ON at any time, the powerindicator will automatically be turned on.NOTE If this does not improve the screen image, restore the factory default settings. If necessary, execute theWHITE BALANCE function again. This function will be enabled only when the input signal is an analogsignal. Exit : Exit: Decrease: Increase: Select another sub-menu EXITMENU OTHERSPOWER INDICATORWHITE BALANCEFACTORY RESETONNONOLANGUAGE ENGLISHBOTTON INDICATOR ONOTHERSBOTTONINDICATORUse this function to set the control keyindicator on the front side of the monitorto ON or OFF.If you set OFF, it will go off. If you set ON , it will be turned on.
19On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.NOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.MONITOR SETUPAUTOMENU ENGINE AUTOSMART INPUT EXITAUTOMENU ENGINE AUTOSMART+ INPUT EXITMONITOR SETUPPress the Button, then the main menu of the OSD appears.SMART+SMART+ON OFFEXITAUTO BRIGHTSub-menusIconsMenu NameButtonTipEXIT : Exit: Adjust (Decrease/Increase) : Restart to select sub-menu
20On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionAUTO BROGHT If select on,it automatically controls thebrightness of display to best suit thesurrounding working environment,providingthe optimal viewing condition and maximizeduser convenience.If select off,auto brightness is off.SMART+EXITWIDEWIDE ORIGINALFULLSMART+ON OFFEXITAUTO BRIGHTSMARTORIGINALRATIOChange the input image signal ratio to4:3. Swith to full screen mode according to input image signal.*This function works only if input resolution is lower than monitor ratio (16:9).
21On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionIMAGE BOOSTERDUAL WEBSMART+EXITAUTO BRIGHTSMART+EXITAUTO BRIGHTSMART+EXITAUTO BRIGHTExit : Exit: Select another sub-menu : MoveSMARTCINEMA MODEON OFFON OFFON OFFHelp to improve image quality.Help user to use web efficiently by dividing in half.Help to arrange and move windows on screen.Help user to control divided windows ratio.Make the eye comfortable by reducing the backgroundbrightness in the web page.* Before using below functions, please install ESP programme.
22On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.NOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.MONITOR SETUPAUTOMENU ENGINE AUTOSMART INPUT EXITAUTOMENU ENGINE AUTOSMART+ INPUT EXITMONITOR SETUPSub-menusIconsNORMAL MOVIE INTERNET DEMOEXITButtonTipEXIT : Exit: Adjust (Decrease/Increase) : Restart to select sub-menu ENGINEMenu NamePress the Button, then the main menu of the OSD appears.ENGINE
23On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionNORMALSelect this when you want to use the product inthe most general using environment. NORMAL MOVIE INTERNET DEMOEXIT ENGINENORMALMOVIE INTERNET DEMOEXIT ENGINENORMALMOVIE INTERNET DEMOEXIT ENGINENORMAL MOVIE INTERNET DEMOEXIT ENGINEMOVIE Select this when you are watching a video ormovie.INTERNETSelect this when you are working on thedocument (Word etc.)DEMOThis is used for advertising in the store. The screenwill be divided to show the standard mode on theleft and video mode on the right so that theconsumers can check the difference after applyingthe video mode. Exit : Exit: Select another sub-menu : MoveF ENGINE
24TroubleshootingNo image appearsCheck the following before calling for service.No image appearsDo you see a "OSD LOCKED" message on the screen?●Is the power cord of thedisplay connected?●Is the power indicatorlight on?●Is the power indicatorflickering?●Do you see an "OUT OFRANGE" message onthe screen?●Do you see a "CHECKSIGNAL CABLE"message on thescreen?• Check and see if the power cord is connectedproperly to the power outlet.• Press the Power button.• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.• Try to turn on the PC.• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED” will appear.●Do you see “OSDLOCKED” when youpush MENU button?
25TroubleshootingDisplay image is incorrect●Display Position isincorrect.●On the screenbackground, verticalbars or stripes arevisible.●Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.• Press the AUTO button to automaticallyadjust your display image to the ideal setting. If the results are unsatisfactory, adjust the imageposition using the H position and V position iconin the on screen display.• Press the AUTO button to automaticallyadjust your display image to the ideal setting.If the results are unsatisfactory, decrease thevertical bars or stripes using the CLOCK icon inthe on screen display.• Press the AUTO button to automaticallyadjust your display image to the ideal setting.If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(true color).IMPORTANTCheck Control Panel --> Display --> Settings and see if the frequency or theresolution were changed. If yes, readjust the video card to the recommendresolution.If the recommended resolution (optimal resolution) is not selected, letters may beblurred and the screen may be dimmed, truncated or biased. Make sure to selectthe recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.
26TroubleshootingDisplay image is incorrect●The screen color ismono or abnormal.●The screen blinks.• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.• Make sure the video card is properly inserted inthe slot.• Set the color setting higher than 24 bits (true color)at Control Panel - Settings.• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.Do you see an "Unrecognized monitor, Plug&Play (VESADDC) monitor found" message?●Have you installed thedisplay driver?• Be sure to install the display driver from the displaydriver CD (or diskette) that comes with yourdisplay. Or, you can also download the driver fromour web site: http://www.lge.com.• Make sure to check if the video card supportsPlug&Play function.
27Specifications E2050SAnti-Glare coating Visible diagonal size : cmDisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green) Sync InputSignal Input 15 pin D-Sub ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm)Video InputMaxResolutionPlug&PlayOn Mode :Sleep Mode ≤Off Mode ≤PowerConsumptionOperating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsAC-DC AdapterType ADS-24S-12 1224G*,manufactured by HONOR Electronicor type MU24-B120200-xx,manufactured by LEADER Electronicsor type ADS-24NP-12-1 12024G,manufactured by HONOR Electronic With Stand Without StandWidth 49.28 cm / 19.40 inches Width 49.28 cm / 19.40 inches Height 38.96 cm / 15.34 inches Height 31.66 cm / 12.46 inches Depth 19.80 cm / 7.80 inches Depth 3.92 cm / 1.54 inchesWeight(excl. packing) 2.6 kg (5.73 lbs)Dimensions& WeightTilt : -5˚~15˚Range12V 2.0APower InputAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2AB20.0 inches (50.8 cm) Flat Panel Active matrix-TFT LCD 50.80.2766 x 0.2766 mm (Pixel pitch)VESA 1600 x 900 @60 HzRecommend VESA 1600 x 900 @60 Hz21 W(Typ.)1 W0.5 WNOTEInformation in this document is subject to change without notice.
Specifications E2250SAnti-Glare coating Visible diagonal size : cmDisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green) Sync InputSignal Input 15 pin D-Sub ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm)Video InputMaxResolutionPlug&PlayOn Mode :Sleep Mode ≤Off Mode ≤PowerConsumptionOperating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsAC-DC AdapterWith Stand Without StandWeight(excl. packing) 2.8 kg (6.17 lbs)Dimensions& WeightTilt : -5˚~15˚Range12V 3.0APower InputAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2AB21.5 inches (54.6 cm) Flat Panel Active matrix-TFT LCD 54.60.248 x 0.248 mm (Pixel pitch)VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 Hz25 W(Typ.)1 W0.5 WNOTEInformation in this document is subject to change without notice.Width 52.58 cm / 20.70 inches Width 52.58 cm / 20.70 inches Height 40.83 cm / 16.07 inches Height 40.08 cm / 15.78 inches Depth 19.80 cm / 7.80 inches Depth 7.88 cm / 3.10 inchesType FSP036D-DGAA1 ,manufactured by FSP Electronicor type LCAPO7E-2 ,ma nufactured by Lienchange Electronics28
Specifications E2350SAnti-Glare coating Visible diagonal size : cmDisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green) Sync InputSignal Input 15 pin D-Sub ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm)Video InputMaxResolutionPlug&PlayOn Mode :Sleep Mode ≤Off Mode ≤PowerConsumptionOperating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsAC-DC AdapterWith Stand Without StandWeight(excl. packing) 3.3 kg (7.28 lbs)Dimensions& WeightTilt : -5˚~15˚Range12V 3.0APower InputAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2AB23.0 inches (58.4 cm) Flat Panel Active matrix-TFT LCD 58.40.265 x 0.265 mm (Pixel pitch)VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 Hz28 W(Typ.)1 W0.5 WNOTEInformation in this document is subject to change without notice.Width 55.98 cm / 22.04 inches Width 55.98 cm / 22.04 inches Height 42.81 cm / 16.85 inches Height 39.60 cm / 15.59 inches Depth 19.80 cm / 7.80 inches Depth 7.87 cm / 3.06 inchesType FSP036D-DGAA1 ,manufactured by FSP Electronicor type LCAPO7E-2 ,ma nufactured by Lienchange Electronics29
Specifications E2050T20.0 inches (50.8 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8cm0.2766 x 0.2766 mm (Pixel pitch)DisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green), DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo InputMax VESA 1600 x 900 @60 HzRecommend VESA 1600 x 900 @60 HzResolutionPlug&PlayOn Mode :21 W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsDimensions& WeightTilt : -5˚~15˚RangeAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B(Digital), DDC2AB(Anlaog)AC-DC Adapter12V 2.0APower InputNOTEInformation in this document is subject to change without notice.With Stand Without StandWidth 49.28 cm / 19.40 inches Width 49.28 cm / 19.40 inches Height 38.96 cm / 15.34 inches Height 31.66 cm / 12.46 inches Depth 19.80 cm / 7.80 inches Depth 3.92 cm / 1.54 inchesWeight(excl. packing) 2.6 kg (5.73 lbs)Type ADS-24S-12 1224G*,manufactured by HONOR Electronicor type MU24-B120200-xx,manufactured by LEADER Electronicsor type ADS-24NP-12-1 12024G,manufactured by HONOR Electronic 30
31Specifications E2250TNOTEInformation in this document is subject to change without notice.21.5 inches (54.6 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6cm0.248 x 0.248 mm (Pixel pitch)DisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green), DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo InputMax VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 HzResolutionPlug&PlayOn Mode :25 W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandWidth 52.58 cm / 20.70 inches Width 52.58 cm / 20.70 inches Height 40.83 cm / 16.07 inches Height 40.08 cm / 15.78 inches Depth 19.80 cm / 7.80 inches Depth 7.88 cm / 3.10 inchesWeight(excl. packing) 2.8 kg (6.17 lbs)Dimensions& WeightTilt : -5˚~15˚RangeAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord Without StandDDC 2B(Digital), DDC2AB(Anlaog)AC-DC Adapter12V 3.0APower InputType FSP036D-DGAA1 ,manufactured by FSP Electronicor type LCAPO7E-2 ,ma nufactured by Lienchange Electronics
32Specifications E2350TNOTEInformation in this document is subject to change without notice.23.0 inches (58.4 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 58.4cm0.265 x 0.265 mm (Pixel pitch)DisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green), DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo InputMax VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 HzResolutionPlug&PlayOn Mode :28 W(Typ.)Sleep Mode ≤ 1 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandWidth 55.98 cm / 22.04 inches Width 55.98 cm / 22.04 inches Height 42.81 cm / 16.85 inches Height 39.60 cm / 15.59 inches Depth 19.80 cm / 7.80 inches Depth 7.87 cm / 3.06 inchesWeight(excl. packing) 3.3 kg (7.28 lbs)Dimensions& WeightTilt : -5˚~15˚RangeAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord Without StandDDC 2B(Digital), DDC2AB(Anlaog)AC-DC Adapter12V 3.0APower InputType FSP036D-DGAA1 ,manufactured by FSP Electronicor type LCAPO7E-2 ,ma nufactured by Lienchange Electronics
33SpecificationsPreset Modes (Resolution)Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)12345678*9720 x 400640 x 480640 x 480800 x 600800 x 6001024 x 7681024 x 7681152 x 8641600 x 90031.46831.46937.50037.87946.87548.36360.12367.50060.000706075607560757560* Recommend ModeE2050S/E2050TE2250S/E2350S/E2250T/E2350TDisplay Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)1720 x 400 31.468 702640 x 480 31.469 603640 x 480 37.500 754800 x 600 37.879 605800 x 600 46.875 7561024 x 768 48.363 6071024 x 768 60.123 7581152 x 864 67.500 7591280 x 1024 63.981 6010 1280 x 1024 79.976 7511 1680 x 1050 65.290 60*12 1920 x 1080 67.500 60* Recommend ModeIndicatorMODELED ColorOn ModePurpleSleep Mode Purple Blinking Off ModeOff
Digitally yours

Navigation menu