LG Electronics USA E2411PUX Part15 Subpart B-LCD Monitor User Manual W19 2243S T ENG

LG Electronics USA Part15 Subpart B-LCD Monitor W19 2243S T ENG

Contents

BEJE2411PUX_User Manual 1

www.lg.comOWNER’S MANUALLCD MONITOR LCD MONITOR MODEL        E2211PUE2411PUPlease read this manual carefully before operating your set and retain it for future reference.ENGLISH
1This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical  shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The power supply cord is used as the main disconnection device. Ensure that thesocket-outlet is easily accessible after installation.Operate the display only from a power source indicated in the specifications of thismanual or listed on the display. If you are not sure what type of power supply youhave in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call yourservice technician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display.  To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock. Important Precautions
2Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity.
Important Precautions3On CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water or otherliquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining.  On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.On Disposal Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
4Accessories!!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.User's Guide/Cards Power Cord15-pin D-Sub Signal Cable(To set it up, this signal cable may beattached to  this product beforeshipping out.)DVI-D Signal Cable(This feature is not available in allcountries.)NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores to maintain standard compliance for the product.USB Cable Audio Cable
Connecting the Display5Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices are turned off. 1. Place the monitor with its front facing downward on a cushion or soft cloth.2.Assemble the Stand Base into the Stand Body.Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. WARNING The tape and locking pin may only be removed from those monitors equipped with astanding base when the base is pulled up. Otherwise, you may be injured by the protrudingsections of the stand.Product Handling with Care :  When you lift up or move the product, Do Not hold or touch thefront part of LCD panel. It will damage the panel. (Please hold the Stand Body or plastic cover ofthe product.)Stand BaseStand BodyStop PinE2211PUConnecting the stand base
6Connecting the DisplayIMPORTANTThis illustration depicts the general model of connection. Your monitor may differ from the itemsshown in the picture.Do not carry the product upside down holding only the stand base. The product may fall and getdamaged or injure your foot.3. Use a coin on the back of the stand base and turn the screw clockwise to tighten.4.Lift and turn the monitor to face towards the front after the connection is made to the female part of the cable you're attaching.2. When you desire to disintegrate the monitor from the stand base, use a coin to turn the      screw counterclockwise.E2211PURemoving the stand base1. Place the monitor with its front facing downward on a cushion or soft cloth.
Connecting the Display7Before setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices are turned off. 1. Place the monitor with its front facing downward on a cushion or soft cloth.2.Assemble the Stand Base into the Stand Body.Be sure don't pull out the Stop Pin and make the Stand Base direction as shown. Stand BaseStand Body Stop PinWARNING The tape and locking pin may only be removed from those monitors equipped with astanding base when the base is pulled up. Otherwise, you may be injured by the protrudingsections of the stand.Product Handling with Care :  When you lift up or move the product, Do Not hold or touch thefront part of LCD panel. It will damage the panel. (Please hold the Stand Body or plastic cover ofthe product.)E2411PUConnecting the stand base3. Once assembled take the monitor up carefully and face the front side.
8Connecting the DisplayIMPORTANTThis illustration depicts the general model of connection. Your monitor may differ from the itemsshown in the picture.Do not carry the product upside down holding only the stand base. The product may fall and getdamaged or injure your foot.Removing the stand base1. Place the monitor with its front facing downward on a cushion or soft cloth.2. While pressing the latches, push the stand base in the direction of the arrow to separatefrom the stand body.E2411PU
Positioning your displayAfter installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort.Tilt Range : -4˚ to17˚                   Connecting the DisplayHeight Range : maximum 4.33 inches (110.0 mm)* Please be sure toremove the Locking pin to adjust the height.110.0 mm42LD42042LD4209Swivel  Range : 356˚
10Connecting the DisplayERGONOMICIt is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tiltangle of the monitor should not exceed 5 degrees.WARNINGYou do not need to replace the Locking pin  after it is removed, to adjust its height. When adjusting the angle of the screen, do not put your finger(s) inbetween the head of the monitor and the stand body. You can hurt yourfinger(s).When adjusting the height of the screen, do not put your finger(s) inbetween the head of the monitor and the stand base. You can hurt yourfinger(s).
11Connecting the Display-The pivot function allows you to rotate the screen 90 degrees clockwise. 1.Lift the monitor to its highest height to utilize the Pivot function.2.Landscape & Portrait : You can rotate the panel 90o  clockwise. Please be cautious and avoid contact between the monitor head and theStand Base when rotating the screen to access the Pivot function. If themonitor head touches the Stand Base, then the Stand Base could crack.3.Be careful with the cables when rotating the screen. Using the Pivot functionStand sectionHead section
12Connecting the DisplayABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.  2.Connect signal input cable         and power cord        in order, then tighten the screwof the signal cable. Connecting with the PC 12Wall-outlet typeMac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin  2row connector.When using a D-Sub signal input cable connectorfor Macintosh Varies according to model.DVI-D (This feature is not available in all countries.)Connect the signalinput cable andtighten it up byturning in thedirection of thearrow as shown inthe figure.AC-IN /⬉⑤䕧ܹAC-IN /⬉⑤䕧ܹNOTE  This is a simplified representation of the rear view.This rear view represents a general model; your display may differ from the view as shown.CConnect Audio Cable
NOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screenflicker or tilted screen while using the device or after changing screen resolution, press theAUTO function button to improve resolution. 4. Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function' is executed automatically.(Only Analog Mode)Power ButtonConnecting the Display3. Put the power cord and cables into the cable holder.Cable Holder 13(Only E2411PU)
14Connecting the DisplayConnecting the USB(Universal Serial Bus) Cable Two USB Downstream ports  Connect these ports to a mouse, memory stick or USB hard disk. One USB Upstream port Connect this port to the downstream port of a computer, laptop or USB monitor (Your computer or USB monitor must support USB and have USB ports).  1. You can use the USB port at the back of the monitor to connect peripherals (USBmouse, USB keyboard, etc.) to the monitor, not to the computer.  2.The monitor’s USB terminal supports USB 2.0 and High Speed cables.NOTE  This is a simplified representation of the rear view.This rear view represents a general model; your display may differ from the view as shown.
15Control Panel FunctionsFront Panel ControlsMENU ButtonOSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time by pushingthe MENU button for several seconds. The message"OSD UNLOCKED" should appear.1 2 35 64SUPER ENERGYSAVING ButtonUse this button to enter SUPER ENERGY SAVINGmenu.For more information, refer to page 22.
16Control Panel FunctionsAUTO ButtonAUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always press theAUTO button on the MONITOR SETUP OSD. (OnlyAnalog Mode)This will automatically adjust your display image to theideal settings for the current screen resolution size(display mode).The best display mode isE2211PU/E2411PU: 1920 x 1080INPUT ButtonWhen two input signals are connected, you can select the(SOURCE Hot key) input signal (D-SUB/DVI) you want. When only one signalis connected, it is automatically detected. The defaultsetting is D-Sub. EXIT Button Exit the OSD(On Screen Display).Power Button &Use this button to turn the display on or off.Power IndicatorThe power indicator stays blue if the display is runningproperly (On Mode). If the display is in Sleep Mode , thepower indicator is blinking blue.
17On Screen Display (OSD) Control AdjustmentScreen AdjustmentMaking adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availableadjustments and selections you can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the discretionary Button, then the main menu of the OSD appears.To access a control, use the corresponding Buttons.Use the       /     Buttons to adjust the image to the desired level. Use the        Button to select other sub-menu items.Press the EXIT Button to exit from the OSD. 1234BRIGHTNESS 10050RED50GREEN50BLUEORIGINAL RATIO WIDECOLOR TEMP PRESETPRESET WARMVOLUME 50
18On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus.DSUB : D-SUB(Analog signal) input DVI-D : DVI-D(Digital signal) inputMain menu Sub-menu            Supported inputDescriptionMENUTo adjust the brightness of theBRIGHTNESSDSUBscreenDVI-DORIGINAL RATIOTo adjust the image sizeVOLUMETo adjust the volumeCOLOR TEMP To customize the color of thescreen(PRESET / USER)To adjust the contrast of theCONTRASTscreen  LANGUAGETo customize the screen statusfor a user's operatingenvironmentFACTORY RESETSUPERDSUBTurn on the SUPER ENERGYENERGYON DVI-DSAVING function.SAVINGTurn off the SUPER ENERGYOFFSAVING function.Initialize the SUPER ENERGYRESETSAVING and set to "OFF" mode.NOTE The order of icons may differ depending on the model (18~24).
19Press the MENU Button, then the main menu of the OSD appears.Sub-menusIconsMenu NameButtonTipEXIT   : Exit: Adjust (Decrease/Increase)SET        : Select another sub-menu               : Restart to select sub-menuBRIGHTNESS 10050RED50GREEN50BLUEORIGINAL RATIO WIDECOLOR TEMP PRESETPRESET WARMVOLUME 50NOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.
20On Screen Display(OSD) Selection and Adjustment Main menu Sub menu                DescriptionCOLOR TEMP50RED50GREEN50BLUEPRESET WARMVOLUME 50BRIGHTNESS 100COLOR TEMP PRESET(1/2)ORIGINAL RATIO WIDEVOLUMEBRIGHTNESS 10050RED50GREEN50BLUEORIGINAL RATIO WIDECOLOR TEMP PRESETPRESET WARMVOLUME 50BRIGHTNESS50RED50GREEN50BLUEORIGINAL RATIO WIDECOLOR TEMP PRESETPRESET WARMVOLUME 50BRIGHTNESS 100ORIGINAL RATIO50RED50GREEN50BLUECOLOR TEMP PRESETPRESET WARMVOLUME 50BRIGHTNESS 100ORIGINAL RATIO WIDE(1/2)To adjust the brightness of the screen. Change the input image signal ratio tooriginal. WIDEORIGINALSwitch to full screen mode according toinput image signal.  * This function works only if inputresolution is lower than monitor ratio(16:9).Exit : Exit,      ,        : Move: Select another sub-menuPRESETSelect the screen color. • WARM: Set the screen to warm color    temperature . • MEDIUM: Set the screen to medium  color temperature.• COOL: Set the screen to cool colortemperature.REDSet your own red color levels.GREENSet your own green color levels.BLUESet your own blue color levels.USERTo adjust the volume of headphone/Speaker.
21On Screen Display(OSD) Selection and Adjustment Main menu DescriptionTo choose the language in which thecontrol names are displayed.Press the      ,       buttons to resetimmediately.Restore all factory default settings except"LANGUAGE." To adjust the contrast of the screen.Exit : Exit,      ,        : Move: Select another sub-menu
22On Screen Display(OSD) Selection and Adjustment   You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipPress the SUPER ENERGY SAVING Button, then the main menu of the OSD appears.ExitMoveRestart to select sub-menu
23On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionExit : Exit,     : Move: Select another sub-menuTurn on the SUPER ENERGYSAVING fuction.When current setting value isON,the SUPER SAVING color isgreen.Turn off the SUPER ENERGYSAVING function.Now the monitoris LED SAVING function.When current setting value isOFF,the SUPER SAVING color isgray.Clear the TOTAL POWERREDUCTION and TOTAL CO2REDUCTION values.OK : SelectTOTAL POWER REDUCTION : How much power is saved during using the monitor.TOTAL CO2 REDUCTION : Change the TOTAL POWER REDUCTION to CO2.ONOFFRESET
24On Screen Display(OSD) Selection and Adjustment SUPER SAVINGLED SAVING41551722 inch 24 inchSaving Data depends on the Panel. So,those values should be different fromeach panel and panel vendor.LG accumulate those values using integrated function with 10 minutesbroadcast video signal.LED Saving means that how much power can be saved using WLED Panelinstead of CCFL panel.SUPER Saving means that how much power can be more saved usingSUPER ENERGY SAVING function. NOTESAVING DATA(W/h):
25TroubleshootingNo image appearsCheck the following before calling for service.No image appearsDo you see a "OSD LOCKED" message on the screen?●Is the power cord of thedisplay connected?●Is the power indicatorlight on?●Is the power indicatorflickering?●Do you see an "OUT OFRANGE" message onthe screen?●Do you see a "CHECKSIGNAL CABLE"message on thescreen?• Check and see if the power cord is connectedproperly to the power outlet.• Press the Power button.• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.• Try to turn on the PC.• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED” will appear.●Do you see “OSDLOCKED” when youpush MENU button?
26TroubleshootingDisplay image is incorrect●Display Position isincorrect.●On the screenbackground, verticalbars or stripes arevisible.●Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.• Press the AUTO button to automatically adjustyour display image to the ideal setting. If the results are unsatisfactory, adjust the imageposition using the H position and V position iconin the on screen display.• Press the AUTO button to automatically adjustyour display image to the ideal setting.If the results are unsatisfactory, decrease thevertical bars or stripes using the CLOCK icon inthe on screen display.• Press the AUTO button to automatically adjustyour display image to the ideal setting.If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(true color).IMPORTANTCheck Control Panel --> Display --> Settings and see if the frequency or theresolution were changed. If yes, readjust the video card to the recommendresolution.If the recommended resolution (optimal resolution) is not selected, letters may beblurred and the screen may be dimmed, truncated or biased. Make sure to selectthe recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card    performance. In this case, please ask to the computer or the video card  manufacturer.
27Display image is incorrectTroubleshooting●The screen color ismono or abnormal.●The screen blinks.• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.• Make sure the video card is properly inserted inthe slot.• Set the color setting higher than 24 bits (true color)at Control Panel - Settings.• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.Do you see an "Unrecognized monitor, Plug&Play (VESADDC) monitor found" message?●Have you installed thedisplay driver?• Be sure to install the display driver from the displaydriver CD (or diskette) that comes with yourdisplay. Or, you can also download the driver fromour web site: http://www.lge.com.• Make sure to check if the video card supportsPlug&Play function.
28Specifications                                                                 E2211PU54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6cm0.248 x 0.248 mm (Pixel pitch)DisplayHorizontal Freq. 30 kHz to 83 kHz (Automatic)Vertical Freq. 56 Hz to 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green), DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo InputMax VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 HzResolutionPlug&PlayOn Mode :26 W(Typ.)Sleep Mode ≤0.5 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandWidth    50.92 cm ( 20.04 inch) Height 39.69 cm ( 15.62 inch) (Min.)50.69 cm ( 19.95 inch) (Max.)Depth 21.00 cm (   8.26 inch)Weight(excl. packing)  3.7 kg (8.22 lb)Dimensions& WeightTilt -4˚ to 17˚Swivel                356˚Height              110 mm / 4.33 inchRangeAC 100 - 240 V~  50 / 60 Hz 1.0 A Power InputAttached (     ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B(Digital),DDC2AB(Anlaog)Without StandWidth    50.92 cm ( 20.04 inch) Height 30.42 cm ( 11.97 inch)Depth 5.98 cm (   2.35 inch)
29Specifications                                                                 E2411PU58.4 cm (23 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 58.4cm0.266 x 0.266 mm (Pixel pitch)DisplayHorizontal Freq. 30 kHz to 83 kHz (Automatic)Vertical Freq. 56 Hz to 75 Hz (Automatic)Input Form Separate Sync.SOG (Sync On Green), DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo InputMax VESA 1920 x 1080 @60 HzRecommend VESA 1920 x 1080 @60 HzResolutionPlug&PlayOn Mode :29 W(Typ.)Sleep Mode ≤0.5 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandHeight 43.26 cm ( 17.03 inch) (Min.)54.26 cm ( 21.36 inch) (Max.)Depth 27.11 cm ( 10.67 inch)Weight(excl. packing)  5.1 kg (11.33 lb)Dimensions& WeightTilt -4˚ to 17˚Swivel                356˚Height              110 mm / 4.33 inchRangeAC 100 - 240 V~  50 / 60 Hz 1.2 A Power InputAttached (     ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B(Digital),DDC2AB(Anlaog)Without StandHeight 34.19 cm ( 13.46 inch)Width    56.91 cm ( 22.40 inch)  Width    56.91 cm ( 22.40 inch) Depth 6.30 cm  (  2.48 inch)
30Specifications                                                      NOTEInformation in this document is subject to change without notice.Standard                      USB 2.0, Self-Power Data Rate                Max 480 MbpsPower Consumption   Max 2.5W x 4USBE2211PU/E2411PU
31IndicatorOn ModeSleep ModeOff ModeWhiteWhite BlinkingOffLED ColorMODEDisplay Modes (Resolution)Horizontal Freq. (kHz)Vertical Freq. (Hz)*Recommend ModeE2211PU/E2411PU1234567891011*12720 x 400640 x 480640 x 480800 x 600800 x 6001024 x 7681024 x 7681152 x 8641280 x 10241280 x 10241680 x 10501920 x 108031.46831.46937.50037.87946.87548.36360.12367.50063.98179.97665.29067.500706075607560757560756060SpecificationsPreset Modes (Resolution)
32Installing the Wall mount plateThis monitor satisfies the specifications of the  Wall mount plate orthe interchange device.1. After moving the product to facedownward, make sure to place it on asoft cloth or a cushion to avoid surfacedamage.  2. Separate the head and the stand withthe use of a screwdriver.
33Wall mount plate(Separate purchase)This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plateis purchased.Kensington Security SlotConnected to a lockingcable that can bepurchased separately atmost computer stores.3.Install the Wall mount plate.<Screw Mounting Interface Dimension>Hole spacing : 100 mm x 100 mm.NOTEVESA compatible only with respect to screw mounting interface dimensions and mounting screw     specificationsPlease use VESA standard as below.* 784.8 mm and under (30.9 inch) - Wall Mount Pad Thickness :  2.6 mm- Screw :   4.0 mm x Pitch 0.7 mm x Length 10 mm    * 787.4 mm and above (31.0 inch) - Please use VESA standard wall mount pad and screws. Installing the Wall mount plate
Make sure to read the Safety Precautions before using the product.Keep the OWNER’S MANUAL(CD) in an accessible place for furture reference.The model and serial number of the SET is located on the back or one side of the SET. Record it below should you ever need service.MODELSERIALAs an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-saving guidelines issued by the U.S.Environmental Protection Agency(EPA).

Navigation menu