LG Electronics USA E2441VX Part15 Subpart B-LCD Monitor User Manual W19 2243S T ENG

LG Electronics USA Part15 Subpart B-LCD Monitor W19 2243S T ENG

Contents

BEJE2441VX_User Manual 1

1This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The power supply cord is used as the main disconnection device. Ensure that thesocket-outlet is easily accessible after installation.Operate the display only from a power source indicated in the specifications of thismanual or listed on the display. If you are not sure what type of power supply youhave in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call yourservice technician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display. To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock. Important Precautions
2Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity.
Important Precautions3On CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water or otherliquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining. On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.On Disposal The fluorescent lamp used in this product contains a small amount of mercury.Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
4Accessories!!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.User's Guide/Cards Power Cord15-pin D-Sub Signal Cable(To set it up, this signal cable may beattached to this product beforeshipping out.)DVI-D Signal Cable(This feature is not available in allcountries.)NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores to maintain standard compliance for the product.
Connecting the Display5Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth.2. Assemble the stand Body into theproduct in the correct direction as shown inthe picture. Make sure you push it until youhear it “click”.3. Assemble the Stand Base(Front,Rear) into the Stand Body in thecorrect direction.4. Use a coin on the back of the stand base and turn the screw clockwise totighten.5. Once assembled take the monitor up carefully and face the front side.ImportantThis illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot.Stand Body Hinge BodyStand BodyStand Base
6Connecting the DisplayDisassembling the stand1. Put a cushion or soft cloth on aflatsurface.3. 4. Remove the Stand Body and StandBase from product in correct direction as shown in the picture.2. Place the monitor face Down on thecushion or soft cloth.Use a coin on the back of the StandBase and turn the screw anticlock-wise to loosen.
7Connecting the DisplayBefore setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Positioning your display-After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort.Tilt Range : -5˚ to 15˚ERGONOMICIt is recommended that in order to maintain an ergonomic and comfortable viewing position,the forward tilt angle of the monitor should not exceed 5 degrees.Do not touch or press the screen whenadjusting the angle of the monitor. When adjusting the angle of the screen, donot put your finger(s) in between the head ofthe monitor and the stand body. You canhurt your finger(s).
8Connecting the Display E2241V/E2341V/E2341VG/E2441VNOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screenflicker or tilted screen while using the device or after changing screen resolution, press theAUTO function button to improve resolution. ABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. 2.Connect signal input cable and power cord in order, then tighten the screwof the signal cable. Connecting with the PC12PCPCABWall-outlet typeMac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin 2row connector.When using a D-Sub signal input cable connectorfor Macintosh Varies according to model.DVI-D (This feature is not available in all countries.)NOTE This is a simplified representation of the rear view.This rear view represents a general model; your display may differ from the view as shown.3. Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function' is executed automatically.(Only Analog Mode)Power ButtonConnect the signal input cable and tightenit up by turning in the direction of the arrow as shown in the figure.
9Control Panel FunctionsFront Panel ControlsMENU ButtonOSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time by pushingthe MENU button for several seconds. The message"OSD UNLOCKED" should appear.For D-SUB and DVI inputOnly for HDMI input

Navigation menu