LG Electronics USA HSTND-3951-G LED MONITOR User Manual HP LD4235 and HP LD4735 Digital Signage Displays

LG Electronics USA LED MONITOR HP LD4235 and HP LD4735 Digital Signage Displays

User Manual

HP LD4235 and HP LD4735Digital Signage DisplaysUser Guide
© 2014 Hewlett-Packard DevelopmentCompany, L.P. The information containedherein is subject to change without notice.The only warranties for HP products andservices are set forth in the express warrantystatements accompanying such products andservices. Nothing herein should be construedas constituting an additional warranty. HP shallnot be liable for technical or editorial errors oromissions contained herein.This document contains proprietaryinformation that is protected by copyright. Nopart of this document may be photocopied,reproduced, or translated to another languagewithout the prior written consent of Hewlett-Packard Company.Microsoft and Windows are U.S. registeredtrademarks of the Microsoft group ofcompanies.First Edition (January 2014)Document Part Number: 749846-001
About this guideThis guide provides information on setting up the display, troubleshooting, and technical specifications.WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harmor loss of life.CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage toequipment or loss of information.NOTE: Text set off in this manner provides important supplemental information.iii
iv   About this guide
Table of contents1  Product features ........................................................................................................................................... 1HP Digital Signage models .................................................................................................................................... 1Accessories ............................................................................................................................................................ 2Optional accessories .............................................................................................................................................. 22  Safety and maintenance guidelines ................................................................................................................ 3Important safety information ............................................................................................................................... 3Maintenance guidelines ......................................................................................................................................... 3Cleaning the display ............................................................................................................................ 43  Assembling and preparing .............................................................................................................................. 5Using the IR receiver .............................................................................................................................................. 6Portrait layout ....................................................................................................................................................... 7Using the security system ..................................................................................................................................... 7Mounting on a wall ................................................................................................................................................. 8Securing the product to a wall (optional) ........................................................................................... 94  Remote control ........................................................................................................................................... 10Remote control buttons ...................................................................................................................................... 115  Using the display ......................................................................................................................................... 13Connecting to a Digital Signage media player or computer ............................................................................... 13RGB/VGA connection ......................................................................................................................... 14DisplayPort connection ..................................................................................................................... 15HDMI connection ...............................................................................................................................  16IR receiver connection ....................................................................................................................... 17LAN/VOE connection .........................................................................................................................  18Connecting the display using LAN/VOE .......................................................................... 18Connecting multiple displays to one player ................................................................... 19Connecting multiple displays with Video Over Ethernet (VOE) ................... 19Connecting multiple displays with Tile Mode .............................................. 19Adjusting the screen ............................................................................................................................................ 22Selecting an image mode .................................................................................................................. 22Customizing image options ..............................................................................................................  22Customizing computer display options ............................................................................................ 23Adjusting sound ................................................................................................................................................... 23v
Selecting a sound mode .................................................................................................................... 23Customizing sound options .............................................................................................................. 24Using additional options ...................................................................................................................................... 24Using the input list ............................................................................................................................ 24Adjusting aspect ratio ....................................................................................................................... 2416:9 : This selection will allow you to adjust the picture horizontally, in linearproportion, to fill the entire screen (useful for viewing 4:3 formatted DVDs). ............. 25Just Scan : This Selection will allow you to view the best quality picture withoutloss of the original picture in high resolution image. .................................................... 251:1 : The aspect ratio is not adjusted from the original. (Only Display Port PC,HDMI PC, RGB PC) ............................................................................................................ 264:3 : This selection will allow you to view a picture with an original 4:3 aspectratio, black bars will appear on both the left and right of the screen. .......................... 26Zoom : This selection will allow you to view the picture without any alteration,while filling the entire screen. However, the top and bottom of the picture will becropped. .......................................................................................................................... 26Cinema Zoom : Choose Cinema Zoom when you want to enlarge the picture incorrect proportion. Note: When enlarging or reducing the picture, the image maybecome distorted. ........................................................................................................... 276  Customizing settings ................................................................................................................................... 28Accessing main menus ........................................................................................................................................ 28PICTURE settings ............................................................................................................................... 29Picture Mode options ...................................................................................................... 30Advanced control ............................................................................................................ 30AUDIO settings .................................................................................................................................. 31TIME settings ..................................................................................................................................... 32OPTION settings ................................................................................................................................ 33Picture ID ........................................................................................................................................... 38NETWORK settings ............................................................................................................................ 387  Making connections ..................................................................................................................................... 40Connecting to a Computer, HD receiver, DVD, or VCR ......................................................................................... 41DisplayPort connection ..................................................................................................................... 41HDMI connection ............................................................................................................................... 42Component connection ..................................................................................................................... 43Connecting to the LAN ......................................................................................................................................... 44Connecting to a USB ............................................................................................................................................ 44Daisy chain displays ............................................................................................................................................. 45vi
8  Setting up the display for music, videos, and photos ...................................................................................... 46Network status .................................................................................................................................................... 48Connecting USB storage devices ......................................................................................................................... 48Browsing files ...................................................................................................................................................... 50Supported file format ....................................................................................................................... 51Playing videos ...................................................................................................................................................... 52Viewing photos .................................................................................................................................................... 55Listening to music ................................................................................................................................................ 57Using PIP/PBP ...................................................................................................................................................... 599  Troubleshooting .......................................................................................................................................... 6110  Specifications ........................................................................................................................................... 6342-inch models .................................................................................................................................................... 63Dimensions ........................................................................................................................................ 6547-inch models .................................................................................................................................................... 66Dimensions ........................................................................................................................................ 68Recognizing preset display resolutions .............................................................................................................. 69DTV mode ............................................................................................................................................................. 70IR codes ................................................................................................................................................................ 7011  Agency regulatory notices .......................................................................................................................... 72Federal Communications Commission notice ..................................................................................................... 72Modifications ..................................................................................................................................... 72Cables ................................................................................................................................................ 72Declaration of Conformity for products marked with the FCC logo (United States only) .................................. 72Canadian notice ................................................................................................................................................... 73Avis Canadien ....................................................................................................................................................... 73European Union regulatory notice ...................................................................................................................... 73German ergonomics notice ................................................................................................................................. 74Japanese notice ................................................................................................................................................... 74Korean notice ....................................................................................................................................................... 74Power cord set requirements .............................................................................................................................. 74Japanese power cord requirements ................................................................................................. 74Product environmental notices ........................................................................................................................... 75Materials disposal ............................................................................................................................. 75Disposal of waste equipment by users in private households in the European Union ................... 75Chemical substances ......................................................................................................................... 75HP recycling program ........................................................................................................................ 75Restriction of Hazardous Substances (RoHS) ................................................................................... 75vii
Turkey EEE regulation ....................................................................................................................... 76Ukraine Restriction of Hazardous Substances ................................................................................. 7612  Controlling multiple products ..................................................................................................................... 77Connecting the cable ........................................................................................................................................... 77RS-232C configurations ...................................................................................................................................... 77Communication parameter ................................................................................................................................. 78Command reference list ...................................................................................................................................... 78Transmission / Receiving protocol ...................................................................................................................... 80Transmission ..................................................................................................................................... 80Acknowledgement ............................................................................................................................ 8001. Power (Command: k a) .............................................................................................. 8002. Input Select (Command: x b) .................................................................................... 8103. Aspect Ratio (Command: k c) .................................................................................... 8104. Energy Saving (Command: j q) .................................................................................. 8205. Picture Mode (Command: d x) ................................................................................... 8206. Contrast (Command: k g) .......................................................................................... 8207. Brightness (Command: k h) ...................................................................................... 8308. Sharpness (Command: k k) ....................................................................................... 8309. Color (Command: k i) ................................................................................................ 8310. Tint (Command: k j) ................................................................................................... 8311. Color Temperature (Command: x u) ......................................................................... 8412. H Position (Command: f q) ........................................................................................ 8413. V Position (Command: f r) ......................................................................................... 8414. H Size (Command: f s) ............................................................................................... 8515. Auto Configuration (Command: j u) .......................................................................... 8516. Balance (Command: k t) ............................................................................................ 8517. Sound Mode (Command: d y) .................................................................................... 8518. Treble (Command: k r) .............................................................................................. 8619. Bass (Command: k s) ................................................................................................. 8620. Speaker (Command: d v) ........................................................................................... 8621. Volume Mute (Command: k e) .................................................................................. 8622. Volume Control (Command: k f) ............................................................................... 8723. Time 1(Year/ Month/ Day) (Command: f a) .............................................................. 8724. Time 2(Hour/ Minute/ Second) (Command: f x) ....................................................... 8725. Off Timer(Repeat Mode/ Time) (Command: f e) ....................................................... 8826. On Timer(Repeat Mode/ Time) (Command: f d) ....................................................... 8927. On Timer Input (Command: f u) ................................................................................ 9128. Sleep Time (Command: f f) ....................................................................................... 9229. Power On Delay (Command: f h) ............................................................................... 9230. Automatic Standby (Command: m n) ....................................................................... 92viii
31. Auto Off (Command: f g) ........................................................................................... 9332. Language (Command: f i) .......................................................................................... 9333. ISM mode (Command: j p) ......................................................................................... 9434. Auto-Switch Input Select (Command: m i) ............................................................... 9435. Auto-Switch Input Select (Command: m j) ............................................................... 9436. Reset (Command: f k) ............................................................................................... 9537. Tile Mode (Command: d d) ........................................................................................ 9538. Tile Mode Check (Command: d z) .............................................................................. 9539. Tile ID (Command: d i) ............................................................................................... 9640. Tile H Position (Command: d e) ................................................................................ 9641. Tile V Position (Command: d f) ................................................................................. 9642. Tile H Size (Command: d g) ....................................................................................... 9743. Tile V Size (Command: d h) ....................................................................................... 9744. Natural Mode (In Tile Mode) (Command : d j) ........................................................... 9745. DPM Select (Command: f j) ....................................................................................... 9846. Temperature Value (Command: d n) ........................................................................ 9847. Remote Controller Lock/ Key Lock (Command: k m) ............................................... 9848. Key (Command: m c) ................................................................................................. 9949. OSD Select (Command: k l) ....................................................................................... 9950. Elapsed time return (Command: d l) ........................................................................ 9951. Serial No.Check (Command: f y) ............................................................................... 9952. S/W Version (Command: f z) ................................................................................... 10053. White Balance Red Gain (Command: j m) ............................................................... 10054. White Balance Green Gain (Command: j n) ............................................................. 10055. White Balance Blue Gain (Command: j o) ............................................................... 10056. Backlight (Command: m g) ..................................................................................... 101ix
x
1 Product featuresHP Digital Signage modelsThe HP LCD digital signage displays have a wide-aspect active matrix thin-film transistor (TFT) panel. Thedisplays features include the following:●HP LD4235 model, 106.7 cm (42-inch diagonal) widescreen viewable area display with 1920 x 1080native resolution●HP LD4735 model, 119.28 cm (47-inch diagonal) widescreen viewable area display with 1920 x 1080native resolution●Viewing angles of 178 degrees horizontal, 178 degrees vertical●VGA, HDMI, DisplayPort, VOE, USB, IR, and audio inputs●VGA, DisplayPort, and speaker outputs●RS232, LAN, and IR external controls●External speaker option audio support●USB built-in player, Network utility software, video daisy-chaining using DP and VGA, group IR for tiling(daisy-chain via RS232); Video-over-Ethernet (VOE)●Support VESA compliant mounting interface:◦HP LD4235: 200 x 200 mm (7.87 x 7.87 in) hole pattern◦HP LD4735: 400 x 400 mm (15.75 x 15.75 in) hole pattern●Network Sign Manager (NSM) software utility provided that allows remote, centralized managementand control of HP digital signage displays. Users have the ability to monitor and send commands to allthe network connected displays in a subnet from a central location such as a data center. For moreinformation, see the HP Network Sign Manager User Guide provided with the display.●HP Video Over Ethernet (VOE) compatibility that provides a system of software, hardware, and firmwarefor connecting HP Digital Signage Displays on a network with computers/media players on the samenetwork. For more information, see the HP Video Over Ethernet User Guide provided with the display.HP Digital Signage models 1
Accessories●Software and documentation disc●Remote control (includes AAA batteries)●Power cord●DisplayPort cable●HDMI cable●RGB (VGA) cable●IR receiverOptional accessoriesOptional accessories (purchased separately) might vary depending on the model.●Stand kit●Speaker kit●Wall mount kit2 Chapter 1   Product features
2 Safety and maintenance guidelinesImportant safety informationA power cord is included with the display. If another cord is used, use only a power source and connectionappropriate for this display.WARNING! To reduce the risk of electric shock or damage to the equipment:• Do not disable the power cord grounding feature. The grounding plug is an important safety feature.• Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.• Disconnect power from the product by unplugging the power cord from the electrical outlet.For your safety, do not place anything on power cords or cables. Arrange them so that no one canaccidentally step on or trip over them. Do not pull on a cord or cable. When unplugging from the electricaloutlet, grasp the cord by the plug.To reduce the risk of serious injury, read the Safety and Comfort Guide. It describes proper workstation,setup, posture, and health and work habits for computer users, and provides important electrical andmechanical safety information. This guide is located on the Web at www.hp.com/ergo and/or on thedocumentation disc, if one is included with the display.CAUTION:  For the protection of the display, as well as the media player/computer, connect all power cordsfor the media player/computer and its peripheral devices (such as a display, printer, scanner) to some form ofsurge protection device such as a power strip or Uninterruptible Power Supply (UPS). Not all power stripsprovide surge protection; the power strips must be specifically labeled as having this ability. Use a powerstrip whose manufacturer offers a Damage Replacement Policy so you can replace the equipment, if surgeprotection fails.Use the appropriate and correctly sized furniture designed to properly support your display.WARNING! Displays that are inappropriately situated on dressers, bookcases, shelves, desks, speakers,chests, or carts can fall over and cause personal injury.Care should be taken to route all cords and cables connected to the display so that they cannot be pulled,grabbed, or tripped over.CAUTION: Do not place the device in a location where water may drip and/or splash on the device.Do not place an object that contains water, such as a flower vase, on the device.Maintenance guidelinesTo enhance the performance and extend the life of the display:●Do not open the display cabinet or attempt to service this product yourself. Adjust only those controlsthat are covered in the operating instructions. If the display is not operating properly or has beendropped or damaged, contact an authorized HP dealer, reseller, or service provider.●Use only a power source and connection appropriate for this display, as indicated on the label/backplate of the display.●Be sure the total ampere rating of the products connected to the outlet does not exceed the currentrating of the electrical outlet, and the total ampere rating of the products connected to the cord doesImportant safety information 3
not exceed the rating of the cord. Look on the power label to determine the ampere rating (AMPS or A)for each device.●Install the display near an outlet that you can easily reach. Disconnect the display by grasping the plugfirmly and pulling it from the outlet. Never disconnect the display by pulling the cord.●Turn the display off when not in use. You can substantially increase the life expectancy of the display byusing a screen saver program and turning off the display when not in use.CAUTION: Burn-in or image sticking might occur on displays which display the same static image onthe screen for prolonged periods of time. To avoid burn-in or image sticking and to prolong the life ofthe display, you should activate one of the four ISM selections in the OSD, activate a screen-saverapplication, periodically cycle between static information and moving images, or turn off the displaywhen it is not in use for prolonged periods of time.●Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked orcovered. Never push objects of any kind into cabinet slots or other openings.●Do not drop the display or place it on an unstable surface.●Do not allow anything to rest on the power cord. Do not walk on the cord.●Keep the display in a well-ventilated area, away from excessive light, heat or moisture.●When removing the display base, you must lay the display face down on a soft area to prevent it fromgetting scratched, defaced, or broken.Cleaning the display1. Turn off the display and unplug the power cord from the back of the unit.2. Dust the display by wiping the screen and the cabinet with a soft, clean antistatic cloth.3. For more difficult cleaning situations, use a 50/50 mix of water and Isopropyl alcohol.CAUTION: Spray the cleaner onto a cloth and use the damp cloth to gently wipe the screen surface. Neverspray the cleaner directly on the screen surface. It might seep behind the bezel and damage the electronics.CAUTION: To clean the display screen or cabinet, do not use cleaners that contain any petroleum-basedmaterials such as benzene or thinner or any volatile substance. These chemicals might damage the display.4 Chapter 2   Safety and maintenance guidelines
3 Assembling and preparingItem Connection panel Description(1) HDMI Connects voice or audio input cable.  DP IN Connects DisplayPort in cable to the display.  DP OUT Connects DisplayPort out cable to the display.  LAN/VOE Connects a local area network cable.  SPEAKER OUT Connects optional external speakers to the display.  AUDIO IN Connects an audio cable to the display.  RGB/AV COMPONENT OUT Connects an RGB/AV component out cable to the display.  RGB/AV COMPONENT IN Connects an RGB/AV component in cable to the display.  RS-232C OUT Connects an RS-232C out cable to the display.  RS-232C IN Connects an RS-232C in cable to the display.  USB Connects a USB cable to the display.  IR IN Connects an IR cable to the display.5
Item Screen marks Description(2) INPUT Changes the input source.  MENU Accesses the main menus, or saves your input and exits the menus. Moves the selection up and down. Adjusts the volume level.  AUTO/SET Displays the current signal and mode. Press this button to adjust the screen automatically (RGB modeonly). Turns the power on or off.Using the IR receiverThis allows a remote control sensor to be placed in a custom location.NOTE: The IR receiver is made with a magnet. If it is attached to the side or the bottom of the product,external shocks may cause the IR receiver to fall. It is recommended to attach it to the back of the product.6 Chapter 3   Assembling and preparing
Portrait layoutTo install in portrait orientation, rotate the display counterclockwise 90 degrees when looking at it from thefront.Using the security systemThe security system connector is located at the back of the display.Connect the security system cable between the display and a table.NOTE: The security system is separately purchased. You can obtain additional accessories from mostelectronics stores.Portrait layout 7
Mounting on a wallFor proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installationinstructions are available from the manufacturer of the mounting equipment..If you intend to mount the display to a wall, attach a wall mounting interface (optional parts) to the back ofthe set.When you install the display using a wall mounting interface (optional parts), attach it carefully so it will notfall.1. Use a wall mount and screws in accordance with VESA Standards.If you use screws longer than the VESA standard, the display might be damaged internally.If you use improper screws, the product might be damaged and drop from mounted position. In thiscase, HP is not responsible for damage.2. Use VESA standard as follows:●785 mm (31 inch) or greater●Fastening screw: Diameter 6.0 mm x Pitch 1.0 mm x Length 10 mmCAUTION: Disconnect the power cord first, and then move or install the display. Otherwise electric shockmay occur.If you install the display on a ceiling or slanted wall, it may fall and result in severe injury.Use an authorized HP wall mount and contact the local dealer or qualified personnel.Do not over tighten the screws as this may cause damage to the display and void your warranty.Use the screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using animproper accessory are not covered by the warranty.NOTE: The wall mount bracket is optional. You can obtain additional accessories from your local dealer.The length of screws may differ depending on the wall mount. Be sure to use the proper length.For more information, refer to the manufacturer’s instructions supplied with the wall mount.8 Chapter 3   Assembling and preparing
Securing the product to a wall (optional)1. Insert and tighten eye-bolts or product brackets and bolts on the back of the product. If there are boltsinserted at the eye-bolts position, remove the bolts first.NOTE: Eye-bolts or wall brackets are not included with the display.2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the product.3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the ropehorizontal with the flat surface.CAUTION: Make sure that children do not climb on or hang on the product.NOTE: Use a platform or cabinet that is strong and large enough to support the product securely.Brackets, bolts and ropes are optional. You can obtain additional accessories from your local dealer.WARNING! If a product is not positioned in a sufficiently stable location, it can be potentially hazardous dueto falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as:●Using cabinets or stands recommended by the manufacturer of the product.●Only using furniture that can safely support the product.●Ensuring the product is not overhanging the edge of the supporting furniture.●Not placing the product on tall furniture (for example, cupboards or bookcases) without anchoring boththe furniture and the product to a suitable support.●Not standing the product on cloth or other materials placed between the product and supportingfurniture.●Educating children about the dangers of climbing on furniture to reach the product or its controls.Mounting on a wall 9
4 Remote controlThe remote control ships with batteries.To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching (+) and (-) ends to thelabel inside the compartment, and close the battery cover. To remove the batteries, perform the installationactions in reverse.CAUTION: Do not mix old and new batteries, as this may damage the remote control.Make sure to point the remote control to the remote control sensor on the display.10 Chapter 4   Remote control
Remote control buttonsItem Button Function  Item Button Function(1) Power Turns the display on or off.   (7) MUTE Mutes all sound.(2) MONITORON/OFFTurns off the display then turns itback on. (8) ENERGY SAVING Adjusts the brightness on the screen toreduce energy consumption.(3) MARK Selects a specific file in USB mode.   (9) INPUT Selects Input mode.(4) ARC Selects the aspect ratio.   (10) Number andalphabetbuttonsEnters numerical or alphabeticalcharacters depending on the setting.(5) Volume up/downAdjusts the volume level.   (11) BRIGHTNESS key Adjust the brightness by pressing theUp and Down buttons on the remotecontrol. In USB mode, the OSD menuhas the Page function to move to thenext file list.(6) PSM Selects Picture Status Mode.        Remote control buttons 11
Item Button Function  Item Button Function(14) MENU Accesses the main menus orsaves your input and exits menus. (19) AUTO Automatically adjusts picture positionand minimizes image instability (RGBinput only).(15) NavigationbuttonsScrolls through menus or options.   (20) USB Selects USB menu to control the HPMedia Sign Player.(16) OK Selects menus or options andconfirms your input. (21) EXIT Clears all on-screen displays and returnsto display viewing from any menu.(17) BACK Allows the user to move back onestep in user interaction function. (22) TILE Selects Tile mode.(18) ID ON/OFF When the number of Picture ID isequal to Set ID, you can controlthe display you want in multidisplay mode. (23) USB Menucontrol buttonsControl media playback.12 Chapter 4   Remote control
5 Using the displayConnecting to a Digital Signage media player or computerYour display supports the Plug and Play feature. In Plug and Play, a computer will have a built-in driver forthe display, no extra software is needed.NOTE: It is recommended you use a DisplayPort connection for the best image quality.Use a shielded signal interface cable, such as D-sub 15 pin signal cable and HDMI cable, with a ferrite core tomaintain standard compliance for the product.If you turn the display on when the set is cold, the screen may flicker. This is normal.Some red, green, or blue spots may appear on the screen. This is normal.If you use a cable longer than the D-sub 15 pin signal cable provided, certain images may appear blurry. Connect the signal input cable and tighten it by turning the screws clockwise.CAUTION: Do not press the screen with your finger for a long time as this may result in temporarydistortion on the screen.Avoid displaying a fixed image on the screen for a long period of time to prevent image burn. Use a screensaver if possible.Connecting to a Digital Signage media player or computer 13
RGB/VGA connectionTransmits an analog video signal from your computer to the display. Connect the computer and the displaywith a standard RGB/VGA cable as shown in the following illustration. Select RGB/VGA IN connector ondisplay. The audio in cable is not provided with display.If you will be connecting this display to another display via RGB/VGA (daisy chain), plug one end of a secondRGB/VGA cable into the Output RGB/VGA connector on the display and plug the other end of RGB/VGA cableinto the Input RGB/VGA connector on the next display in chain. RGB/VGA connection can have multipledisplays (up to 6) connected to a single player/computer using the tile mode. For more information, seeConnecting multiple displays to one player on page 19.14 Chapter 5   Using the display
DisplayPort connectionTransmits digital video signal from your computer to the display. Connect the computer and the display witha DisplayPort cable as shown the following illustration. Select Display IN. The audio in cable is not providedwith the display.If you will be connecting this display to another display via DisplayPort (daisy chain), plug one end of asecond DisplayPort cable into the DP-OUT connector on the display and plug the other end of DisplayPortcable into the DP-IN connector on the next display in chain. For more information, see Connecting multipledisplays to one player on page 19.Back of the productConnecting to a Digital Signage media player or computer 15
HDMI connectionTransmits the digital video and audio signals from your computer to the display. Connect the computer andthe display with an HDMI cable as shown in the following illustration. Select HDMI input.Back of the productNOTE: Use a high Speed HDMI cable. High speed HDMI cables can handle definition beyond 1080p.Check the computer environment if you cannot hear audio in HDMI mode. Some computers require you tomanually change the default audio output to HDMI.If you want to use HDMI-PC mode, you must set the input label to PC mode.When HDMI PC is used, a compatibility problem might occur.16 Chapter 5   Using the display
IR receiver connectionAllows the use of a wired remote or IR receiver extension. The IR cable is provided with the display.Back of the productNOTE: Make sure the power cable is disconnected.Connecting to a Digital Signage media player or computer 17
LAN/VOE connectionConnecting the display using LAN/VOE▲To connect the display to a network, plug your CAT-5 network cable into the Ethernet port.The Ethernet cable from the display can connect to a media player/computer, a router (switch), or anIntranet. A network connection enables the use of the Video Over Ethernet software to assign a mediaplayer to drive the display. The connection also allows the HP Network Sign Manager program, runningon a networked media player/computer, to send command data.Connect the Ethernet cable using one of the following connections:●Computer Direct Connection—Connect the LAN cable to the LAN port on the display and to the LANport on the media player/computer (1).●Router—Connect the LAN cable to the LAN port on the display and to a LAN port on the router (2).●Intranet—Connect the LAN cable to the LAN port on the display and to the Intranet network via anaccess point (3).18 Chapter 5   Using the display
Connecting multiple displays to one playerMultiple displays may be connected to a single media player/computer two different ways, using Video OverEthernet or using Tile Mode with VGA or DisplayPort video inputs.Connecting multiple displays with Video Over Ethernet (VOE)To connect multiple displays to a single media player/computer, each display must be connected to the samesub-network as the media player/computer. The input source of each display must be set to VOE. With VOE,displays are connected to media players/computer by establishing an association between the media player/computer and one or more displays on the network with the VOE software that runs in the media player/computer. Up to 12 displays may be associated with a single media player/computer (See the VOE UsersGuide provided with the display for more detail). When multiple displays are associated with a single mediaplayer/computer, the displays may be mirrored (a single desktop image displays on all the displayssimultaneously).The image may be extended across all the displays simultaneously using the View Span “Display Resolution”dialog box.The displays may be treated by an application as though there were up to 12 individual displays connected to12 graphic adaptor heads on the media player/computer.The association of up to 12 displays is the technical limit, and depending upon the complexity of the desktopimage to be displayed (playing flash, or streaming video), the number of displays which can be associatedwith acceptable video performance may be less than 12 (See the Video Over Ethernet User Guide for moredetail).Connecting multiple displays with Tile ModeThe recommended cable routing for daisy chain in Tile Mode is to start with the upper left display andconnect across the upper tier of displays going from left to right to the last display in that tier. Then cablefrom the upper right display to the display just below it and connect across from right to left to the lastdisplay on the left. Continue this back and forth, top to bottom cable route for all the tiers in the wall asindicated in the next figure.Connecting to a Digital Signage media player or computer 19
Multiple displays (up to 25 for DP and 6 for RGB/VGA) may be connected to a single media player/computerusing Tile Mode. Multiple displays in Tile Mode are only supported with either DisplayPort or VGA video inputsources. When connecting the multiple displays, the media player/computer is connected to the first displayonly with either a DisplayPort or VGA connection. All the subsequent displays are connected to each other viadaisy chain using either the DP OUT connector from one display to the DP IN connector of the next display, orusing the VGA OUT connector from one display to the VGA IN connector of the next display. All displays mustbe connected with the same video source, either DisplayPort or VGA. When using Tile mode to connectmultiple displays, only one desktop image may be displayed across all the tiled displays.20 Chapter 5   Using the display
To remotely manage and control multiple displays in Tile Mode when using either VGA or DisplayPort videosource, either a RS-232 or Network connection may be used with the HP Network Sign Manager.If using the RS-232 interface, the displays must be daisy chained with RS-232 cables. Attach one end of aRS-232 cable to the RS-232 Input connector of the first display and connect to the serial connector of themedia player/computer. Then attach one end of an RS-232 cable to the RS-232 Output connector and theother end to the RS-232 Input connector of the next display and continue to connect the RS-232 cablesbetween each display in the tiled matrix.If using a Network connection, just attach each display to a network hub or access point using a CAT-5 cable,and HP Network Sign Manager will locate each network attached display. The HP Network Sign Manager willallow users to select any display or assigned group of displays to manage and control. If the display isalready attached to the network for VOE, there is no further action required. The HP Network Sign Managerwill detect the displays via its search function (See the HP Network Sign Manager Users Guide provided withthe display for more details).Multiple displays may also be controlled and managed with the IR Remote Control.NOTE: The number of displays that can be connected by daisy chain to one media player/computer mightvary depending on the signal status and cable loss. If the signal status is good, and there is no cable loss, it ispossible to connect up to 25 displays for DP and 12 displays for RGB/VGA in a daisy chain from one mediaplayer/computer.If you are going to play video that is copy protected with High-bandwidth Digital Content Protection (HDCP),you must use DisplayPort as the video source, and you are limited to a maximum of six displays in the daisychain which can support HDCP.When using Tile Mode, the display ID can be set in the display OSD with the IR Remote Control, the displaycontrol panel, or for Network attached displays, the display ID can be set with the HP Network Sign Managersoftware (See the HP Network Sign Manager User Guide provided with the display for more details).Connecting to a Digital Signage media player or computer 21
Adjusting the screenSelecting an image modeDisplay images in its optimized settings by selecting one of the preset image modes.1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to PICTURE and press OK.3. Press the Navigation buttons to scroll to Picture Mode and press OK.4. Press the Navigation buttons to scroll to an image mode you want and press OK.Option DescriptionVivid Adjusts the video image by enhancing the contrast, brightness, Color, and sharpness.Standard Adjusts the image for the normal environment.Cinema Optimizes the video image for a cinematic look to enjoy videos.Sport Optimizes the video image for high and dynamic actions by emphasizing primary Colors such as white,grass, or sky blue.Game Optimizes the video image to enjoy dynamic image when playing a game.5. When you are finished, press EXIT. When you return to the previous menu, press BACK.Customizing image optionsCustomize basic and advanced options of each image mode for the best screen performance.1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to PICTURE and press OK.3. Press the Navigation buttons to scroll to Picture Mode and press OK.4. Press the Navigation buttons to scroll to an image mode you want and press OK.5. Select and adjust the following options, and then press OK.Option DescriptionBacklight Adjusts the brightness of the screen by controlling the LED backlight. If you decrease the brightness level,the screen becomes darker and the power consumption will be reduced without any video signal loss.Contrast Increases or decreases the gradient of the video signal. You may use Contrast when the bright part of thepicture is saturated.Brightness Adjusts the base level of the signal in the picture. You may use Brightness when the dark part of the pictureis saturated.Sharpness Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower thelevel, the softer the image.Color Adjusts intensity of all colors.Tint Adjusts the balance between red and green levels.Color temp. Set to warm to enhance hotter Colors such as red, or set to cool to make picture bluish.22 Chapter 5   Using the display
AdvancedControlCustomizes the advanced options.Picture Reset Restores the options to the default setting.6. When you are finished, press EXIT. When you return to the previous menu, press BACK.Customizing computer display optionsCustomize options of each image mode for the best image quality.This function works in the following mode: RGB[PC] mode.1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to PICTURE and press OK.3. Press the Navigation buttons to scroll to Screen and press OK.4. Select and adjust following options, and then press OK.Option DescriptionResolution Selects a proper resolution. See Customizing settings on page 28.Auto Config. Sets to adjust the screen position, clock, and phase automatically. The displayed image may beunstable for a few seconds while the configuration is in progress.Position/ Size/Phase Adjusts the options when the picture is not clear, especially when characters are shaky, after theauto configuration.Reset Restores the options to the default setting.5. When you are finished, press EXIT. When you return to the previous menu, press BACK.Adjusting soundSelecting a sound modePlay the sound in its optimized settings by selecting one of the preset sound modes.1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to AUDIO and press OK.3. Press the Navigation buttons to scroll to Sound Mode and press OK.4. Press the Navigation buttons to scroll to an image mode you want and press OK.Mode DescriptionStandard Select when you want standard quality sound.Music Select when you listen to music.Cinema Select when you watch videos.Sport Select when you watch sports events.Game Select when you want to enjoy dynamic sound when playing a game.5. When you are finished, press EXIT. When you return to the previous menu, press BACK.Adjusting sound 23
Customizing sound optionsCustomize options of each sound mode for the best sound quality.1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to AUDIO and press OK.3. Press the Navigation buttons to scroll to Sound Mode and press OK.4. Press the Navigation buttons to scroll to an image mode you want and press OK.5. Select and adjust following options, and then press OK.Option DescriptionInfinite sound Provides 5.1 channel stereo sound from two speakers.Treble Controls the dominant sounds in the output. When you turn up the treble, it will increase the outputto the higher frequency range.Bass Makes the output sound softer. If the bass is increased, the frequency of the output also increases.Reset Resets the sound mode to the default setting.6. When you are finished, press EXIT. When you return to the previous menu, press BACK.Using additional optionsUsing the input listSelecting an input source1. Press INPUT to access the input source list.2. Press the Navigation buttons to scroll to one of the input sources and press OK.Input Source DescriptionAV Watch the contents in a DVD or other external devices, or through a digital set-top box.Component Watch the contents in a DVD or other external devices, or through a digital set-top box.RGB View a computer display on the screen.HDMI Watch contents in a computer, DVD, or digital set-top box or other high definition devices.DisplayPort Watch contents in a computer, DVD or digital set-top box other high definition devices.VOE Watch contents through the Ethernet port.USB Plays the multimedia files saved in the USB.Adjusting aspect ratioCAUTION: All models are not suitable for applications that exhibit static, stationary, or fixed images. Staticimages may cause image retention damage that may appear as stains or watermarks on the screen. Thewarranty does not cover displays that are in use for applications that exhibit static, stationary, or fixedimages for long periods or for 24-hours per day that result in image retention damage. To avoid imageretention damage, turn off the display when it is not in use or use a power management setting, if supportedby your system, to turn off the display when the system is idle.24 Chapter 5   Using the display
NOTE: You can also change the image size by accessing the main menus.Just Scan mode operates when a video signal has resolution of 720p or higher.MODE Component RGBPCDisplayPort HDMIARC DTV PC DTV PC16:9 o o o o o oJust Scan o x oxox1:1 x o x o x o4:3 o o o o o oZoom o x oxoxCinema Zoom o x oxox16:9 : This selection will allow you to adjust the picture horizontally, in linear proportion, to fillthe entire screen (useful for viewing 4:3 formatted DVDs).Just Scan : This Selection will allow you to view the best quality picture without loss of theoriginal picture in high resolution image.NOTE: If there is noise in original picture, you can see the noise at the edge.Using additional options 25
1:1 : The aspect ratio is not adjusted from the original. (Only Display Port PC, HDMI PC, RGB PC)4:3 : This selection will allow you to view a picture with an original 4:3 aspect ratio, black barswill appear on both the left and right of the screen.Zoom : This selection will allow you to view the picture without any alteration, while filling theentire screen. However, the top and bottom of the picture will be cropped.26 Chapter 5   Using the display
Cinema Zoom : Choose Cinema Zoom when you want to enlarge the picture in correct proportion.Note: When enlarging or reducing the picture, the image may become distorted.Using additional options 27
6 Customizing settingsAccessing main menus1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to one of the following menus and press OK.3. Press the Navigation buttons to scroll to the setting or option you want and press OK.4. When you are finished, press EXIT. When you return to the previous menu, press BACK.Item Function Description(1) PICTURE Adjusts the image size, quality, or effect(2) AUDIO Adjusts the sound quality, effect, or volume level.(3) TIME Sets the time, date, or Timer feature.(4) OPTION Customizes the general settings(5) NETWORK Sets up the network.(6) MY MEDIA Display and play video, photo and music content stored on your USB.28 Chapter 6   Customizing settings
PICTURE settings1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to PICTURE and press OK.3. Press the Navigation buttons to scroll to the setting or option you want and press OK.4. When you are finished, press EXIT. When you return to the previous menu, press BACK.Setting DescriptionAspect Ratio Changes the image size to view images at its optimal size.Energy Saving Sets to automatically adjust the screen brightness corresponding to the surroundings.LevelOff: Disables Energy Saving function.Minimum/Medium/Maximum: Selects the brightness level of the LED backlight.Screen Off: The screen turns off in 3 seconds.Smart EnergySavingAdjusts the LED backlight and contrast depending on the screen brightness.LevelOff: Disables the Smart Energy Saving function.On: Enables the Smart Energy Saving function to save power consumption as much as the value set in the smartenergy saving rate.Picture Mode Selects one of the preset image modes or customizes options in each mode for the best display screenperformance. You are also able to customize advanced options of each mode. The available preset picturemodes vary depending on the display.ModeVivid: Adjusts the video image by enhancing the contrast, brightness, Color, and sharpness.Standard: Adjusts the image for the normal environment.Cinema: Optimizes the video image for a cinematic look to enjoy videos.Sport: Optimizes the video image for high and dynamic actions by emphasizing primary Colors such as white,grass, or sky blue.Game: Optimizes the video image for a fast gaming screen such as computers or games.SCREEN (In RGBMode Only)Customizes the computer display options in RGB mode.OptionResolution: Selects a proper resolution. See Customizing settings on page 28.Auto Configure: Sets to adjust the screen position, clock, and phase automatically. The displayed image may beunstable for a few seconds while the configuration is in progress.Position/Size/Phase: Adjusts the options when the picture is not clear, especially when characters are shaky,after the auto configuration.Reset: Restores the options to the default setting.Accessing main menus 29
Picture Mode optionsSetting DescriptionBacklight Adjusts the brightness of the screen by controlling the LED backlight. If you decrease thebrightness level, the screen becomes darker and the power consumption will be reducedwithout any video signal loss.Contrast Increases or decreases the gradient of the video signal. You may use Contrast when thebright part of the picture is saturated.Brightness Adjusts the base level of the signal in the picture. You may use Brightness when the darkpart of the picture is saturated.Sharpness Adjusts the level of crispness in the edges between the light and dark areas of thepicture. The lower the level, the softer the image.Color Adjusts intensity of all colors.Tint Adjusts the balance between red and green levels.Color Temp Set to warm to enhance hotter Colors such as red, or set to cool to make picture bluish.Advanced Control Customizes the advanced options. Refer to the Advanced image options.Picture Reset Restores the options to the default setting.NOTE: If the Picture Mode setting in the Picture menu is set to Vivid, Standard, Cinema, Sport or Game thesubsequent menus will be automatically set.You cannot adjust color and tint in the RGB/ HDMI-PC/ DisplayPort PC mode.When using the Smart Energy Saving function, the screen may look saturated in the white area of a stillimage.If Energy Saving is set to Minimum, Medium, or Maximum, the Smart Energy Saving function is disabled.Advanced controlSetting DescriptionDynamic Contrast (Off/High/ Medium/Low)Adjusts the contrast to keep it at the best level according to the brightness of thescreen. The picture is improved by making bright parts brighter and dark parts darker.(Function works in the following mode - Component, HDMI-DTV, DisplayPort-DTV)Dynamic Color (Off/High/Low) Adjusts screen Colors so that they look livelier, richer and clearer. This feature enhanceshue, saturation and luminance so that red, blue, green and white look more vivid.(Function works in the following mode - Component, HDMI-DTV, DisplayPort-DTV)Clear White (Off/High/Low) Make the white area of screen brighter and more white.Skin Color (-5 to 5) It detects the skin area of video and adjusts it to express a natural skin color.Noise Reduction (Off/High/ Medium/Low) Reduces screen noise without compromising video quality. (Function works in thefollowing mode - Component, HDMI-DTV, DisplayPort-DTV)Digital Noise Reduction (Off/High/Medium/Low)This option reduces the noise produced while creating digital video signals.Gamma (High/Medium/ Low) Set your own gamma value. On the display, high gamma values display whitish imagesand low gamma values display high contrast images.Advanced Control Low: The picture of the screen gets darker.30 Chapter 6   Customizing settings
High: The picture of the screen gets brighter.Set black level of the screen to proper level. (Function works in the following mode -Component, HDMI-DTV, DisplayPort-DTV)AUDIO settings1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to AUDIO and press OK.3. Press the Navigation buttons to scroll to the setting or option you want and press OK.To return to the previous level, press BACK.4. When you are finished, press EXIT. When you return to the previous menu, press BACK.The available audio settings are as follows:Setting DescriptionClear Voice II By differentiating the human sound range from others, it helps users listen to human voices better.Balance Adjusts balance between the left and right speakers according to your room environment.Sound Mode The best sound tone quality will be selected automatically depending on the video type that you arecurrently watching.ModeStandard: The most commanding and natural audio.Music: Select this option to enjoy the original sound when listening to the music.Cinema: Select this option to enjoy sublime sound.Sport: Select this option to watch sports broadcasting.Game: To enjoy dynamic sound when playing a game.NOTE: If sound quality or volume is not at the level you want, it is recommended to use a separatehome theater system or amplifier to cope with different user environments.OptionInfinite Sound: Provides 5.1 channel stereo sound from two speakers.Treble: Controls the dominant sounds in the output. When you turn up the treble, it will increase theoutput to the higher frequency range.Bass: Makes the output sound softer. When you turn up the bass, it will increase the output to thelower Frequency.Reset: Resets the sound mode to the default setting.Digital Audio Input HDMI/Display Port: Outputs the sound of digital signal from HDMI through the display speaker. AudioIn: Outputs the sound through the display speaker by connecting HDMI to the Audio In port.Speaker ON: Enables sound to the display speaker. (* The display speaker is sold separately.)OFF: Disables sound to the display speaker. Use this option when using an external sound device.Accessing main menus 31
TIME settings1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to TIME and press OK.3. Press the Navigation buttons to scroll to the setting or option you want and press OK.To return to the previous level, press BACK.4. When you are finished, press EXIT. When you return to the previous menu, press BACK.The available time settings are as follows:Setting DescriptionClock Sets the time feature.On/Off Timer Sets the time to turn on or off the display.Sleep Timer Sets the length of time until the display turns off. When you turn the display off and turn it on again,the Sleep Timer will be set to off.Power On Delay When connecting multiple displays and turning the power on, the displays are turned on individually toprevent overload.Auto off If Auto off is active and there is no input signal, the set switches to off mode automatically after 15minutes.Automatic Standby If you do not use the display for more than 4 hours, it will be in standby mode automatically.NOTE: Off Time/ On Time can be saved for up to seven schedules; the display is turned on or off at thepreset time in the schedule list. If multiple preset times are stored in the schedule list, this function works atthe nearest time from the current time.Once the on or off time is set, these functions operate daily at the preset time.The scheduled power-on and power-off functions work properly only when the device time is set correctly.When the scheduled power-on and power-off times are the same, the power-off time has priority over thepower-on time if the set is turned on, and vice versa if the set is turned off.32 Chapter 6   Customizing settings
OPTION settings1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to OPTION and press OK.3. Press the Navigation buttons to scroll to the setting or option you want and press OK.To return to the previous level, press BACK.4. When you are finished, press EXIT. When you return to the previous menu, press BACK.The available option settings are as follows:Setting DescriptionLanguage To choose the language in which the control names are displayed.ISM Method A frozen or still picture from a computer/video game displayed on the screen for prolonged periodscould result in a image burn remaining even when you change the image. Avoid allowing a fixed imageto remain on the screen for a long period of time.SettingNormal: Leave on normal if you do not foresee image burn as being a problem.Orbiter: May help prevent image burn. However, it is best not to allow any fixed image to remain on thescreen. To avoid a permanent image on the screen, the screen will move every 2 minutes.Inversion: This function inverts the panel color of the screen. The panel color is automatically invertedevery 30 minutes.White Wash: White wash fills the screen with solid white. This helps removes permanent imagesburned into the screen. A permanent image may be impossible to clear entirely with white wash.DPM Select A user can choose to turn the power saving mode on / off.Auto-Switch Input If there is no input signal, it automatically switches to another input with signal.SettingOff: Stops auto switch of the input source.Auto: Switches to another input source with video signal if no video signal comes from the currentinput source.Manual: Selects the priority of input source for auto switch. When several input sources are found, theinput source with a higher priority will be selected.Factory Reset Select this option to return to the default factory settings.Set ID You can assign a unique Set ID NO (name assignment) to each product when several products areconnected for display. Specify the number (1 to 255) using the button and exit. Use the assigned Set IDto individually control each product using the Product Control Program.Tile Mode Tile Mode:To use this function:●Must connect with multiple displays.●Must be in a function that can be connected to DisplayPort Cable and distributor. The tile modemust be set after identifing the display alignment and ID. Only after pressing the SET button theadjustments made to the settings will be saved.●Tile mode : column x row ( c = 1 to 15 r = 1 to 15)●15 x 15 available.Accessing main menus 33
●Configuration define an array of displays showing a single image (up to 25 DisplayPort and 12RGB/VGA).Auto Config: Sets to adjust the screen position, clock, and phase automatically. The displayed imagemay be unstable for a few seconds while the configuration is in progress.Position: Moving the screen position horizontally and vertically.Size: Adjust the horizontal and vertical size of the screen taking into account the size of the bezel.Natural: Allows the image to retain proportionality across the array by compensating for the width ofthe mullion (the distance between the active display area to the active display area of the adjacentdisplay in the array).Reset: Function to initialize and release Tile. All Tile setting are released when selecting Tile reset andthe screen returns to Full screen.PIP/PBP Displays videos or photos stored in a USB device on a single display by dividing it into the main and subscreens.OptionMode: Sets the type of secondary screen.●*OFF: Disables the secondary screen.●*PIP (Picture In Picture): Displays the secondary screen in the main screen.●*PBP (Picture By Picture): Displays the secondary screen next to the main screen.Position: Adjusts the position of the sub screen (top left, bottom left, top right, bottom right) Thedefault value is the bottom right.Size: Adjusts the size of the sub screen (Size 0 to 10). The default size of PIP (Size: 0) is 480x270; themaximum size 10 is 960x540.NOTE: The Position and Size options are enabled only in PIP mode.Key Lock Disenables or enables rear side control keys. If Key Lock is on, the display controls are disenable (rearside key function).Product/Service Info Displays the model name, software version, serial number, IP address, MAC address and home page.Portrait Mode Rotate OSD clockwise (90°) Option90°: Rotate OSD clockwise 90°.Tile ModeThis display can be tiled with additional displays to create a large tiled display.●Off: When the Tile Mode option is disabled.●1x2: When using 2 displays.34 Chapter 6   Customizing settings
●2x2: When using 4 displays.●3x3: When using 9 displays.●4x4: When using 16 displays.Accessing main menus 35
●5x5: When using 25 displays.Tile Mode – Natural modeWhen active, the part of the image that would normally be displayed in the gap between the displays isomitted.PIP/PBPDisplays videos or photos stored in a USB device on a single display by dividing it into the main and subscreens.Mode*PIP (Picture In Picture): Displays the Sub screen in the main screen.*PBP (Picture By Picture): Displays the Sub screen next to the main screen.PositionAdjusts the position of the subscreen (top left, bottom left, top right, bottom right).36 Chapter 6   Customizing settings
SizeAdjusts the size of the subscreen (Size 0-10).NOTE: The subscreen is only supported when using the USB device.You can only change the size and position in PIP mode.With PBP selected, the Aspect Ratio option in the PICTURE menu is disabled (Fixed as 16:9).While running the PBP function, the Tile Mode function does not work.You must select the output sound before running the PIP or PBP functions. (Select either Main or Sub.)If you fail to select Main or Sub from the sound selection box, and if the OSD disappears after either a periodof time or when the Exit or Back key is pressed, the PIP/PBP subscreen is not activated.You cannot change the sound while running the PIP or PBP functions. If you want to change the sound, restartPIP/PBP.The picture quality of the subscreen is set according to the values selected in the main menu, not the USBdevice.When the power is turned off/on, the PIP/PBP mode is disabled.If you play videos you selected in PIP/PBP mode, the videos will play back repeatedly in succession.Accessing main menus 37
The buttons below work in PIP mode:Button Photo Movie<ox>oxxoxxxoxoxoPicture IDPicture ID is used to change the settings of a specific display using a single IR receiver for multivision.Communication is possible between a set with an IR receiver and other sets using audio cables. Each set isidentified by a set ID. If you assign the Picture ID using the remote control, only displays with the samePicture ID and Set ID can be controlled remotely.1. Press the red ON button on the remote control2. If you press the left/right buttons or press the ON button repeatedly, the Picture ID cycles through OFFand 0 to 4. Assign the ID you want.If you assign the Set ID to each set with multi-vision, and then assign the Picture ID using the red buttonon the remote control, the key command is displayed for the set with the same Set ID and Picture ID. Aset with different Set IDs and Picture IDs cannot be controlled by IR signals.NOTE: For example, if the Picture ID is assigned to 2, the upper right display (Set ID: 2) can be controlled byIR signals.For each set, you can change the settings for the PICTURE, AUDIO, TIME, NETWORK and MY MEDIA menus orthe hot keys on the remote control.If you press the green OFF button for Picture IDs, the Picture IDs for all sets are turned off. If you then pressany button on the remote control, all sets will start working again.Picture ID will be disabled while using the MY MEDIA menu.NETWORK settings1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to NETWORK and press OK.3. Press the Navigation buttons to scroll to the setting or option you want and press OK.To return to the previous level, press BACK.4. When you are finished, press EXIT. When you return to the previous menu, press BACK.The available option settings are as follows:Setting Description38 Chapter 6   Customizing settings
Network Setting Configure the network settings.Network Status Display the network status.●Internet is connected : Externally connected●Network is connected : Only internally connected●Not connected : When there is no network connectionVOE IP Settings Sets the video over Ethernet IP address.VOE Setup These fields are recognized by the Video Over Ethernet software.Display Name – Give this display a name up to 32 alphanumeric characters long for reference through theVOE software.Display Location – Identify this display's physical location in a way meaningful to you. Use up to 32alphanumeric characters.Product Name – Automatically shows either LD4235 or LD4735.Player Name – The computer name of a computer/media player running VOE software whose output is to beplayed on this display. You can enter such a name. The VOE software will enter a name when it assigns avideo source to this display.CAUTION: When setting the Player Name, input delay may occur if you press the buttons on the remotecontrol continuously.Accessing main menus 39
7 Making connectionsConnect various external devices to the ports on the display back panel.1. Find an external device you want to connect to your display shown on the following illustration.2. Check the connection type of the external device.3. Go to the appropriate illustration and check the connection details.Item Source Reference  Item Source Reference(1) Computer HDMI connection on page 42DisplayPort connection on page 41Connecting to the LAN on page 44 (4) HDreceiverHDMI connection on page 42DisplayPort connection on page 41Component connection on page 43(2) USB Connecting to a USB on page 44  (5) DVD HDMI connection on page 42DisplayPort connection on page 41Component connection on page 43(3) Speakers Component connection on page 43  (6) VCR Component connection on page 43NOTE: For sound, you must connect an optional speaker.40 Chapter 7   Making connections
Connecting to a Computer, HD receiver, DVD, or VCRConnect a HD receiver, DVD, or VCR to the display and select an appropriate input mode.DisplayPort connectionTransmits the digital video signal from an external device to the display. Connect the external device and thedisplay with the DisplayPort cable as shown in the following illustration. To transmit an audio signal, connectan optional audio cable.Back of the product:Connecting to a Computer, HD receiver, DVD, or VCR 41
HDMI connectionTransmits the digital video and audio signals from an external device to the display. Connect the externaldevice and the display with the HDMI cable as shown on the following illustration.Back of the product:NOTE: Use a High Speed HDMI Cable.High Speed HDMI Cables are tested to carry an HD signal up to 1080p and higher.42 Chapter 7   Making connections
Component connectionTransmits the analog video and audio signals from an external device to the display. Connect the externaldevice and the display with the 15 pin signal to RCA cable as shown on the following illustration. To displayimages by using progressive scan, make sure to use the component cable.The VGA/RCA cable and audio-in cable are not provided with the display.Back of the product:NOTE: When connecting to the Component port using the shared interface, the port must match up to theinput source. Otherwise, noise may occur.Connecting to a Computer, HD receiver, DVD, or VCR 43
Connecting to the LANa. Using a router (switch).Connect one end of the LAN cable (1) to the display and the other end to the router (2). Connect thesecond LAN cable to the router (3) and the other end of the LAN cable to a computer (4).b. Using the Internet.Connect one end of the LAN cable (1) to the display and the other end to the network (2). Connect thesecond LAN cable to the network (3) and the other end of the LAN cable to a computer (4).Connecting to a USBConnect a USB storage device such as s USB flash memory, external hard drive, MP3 player or a USB memorycard reader to the display and access the USB menu to use various multimedia files.44 Chapter 7   Making connections
Daisy chain displaysUse this function to digital video signal from a computer on multiple displays.1. Connect a signal input cable (DisplayPort cable) to the DP IN port of the first display.2. Connect one end of the signal input cable to the computer.3. Connect one end of a signal input cable to the DP OUT port of the first display and the other end to theDP IN of the second display.DisplayPort cableNOTE: The number of displays that can be connected to one output may vary depending on signal statusand cable loss. If the signal status is good, and there is no cable loss, it is possible to connect up to 9 displays.If you want to connect more than this number of displays, it is recommended to use a distributor.When multi-connecting in/out cascade format, no loss cables are recommended.DP OUT does not work when connecting to a third-party product.Daisy chain displays 45
8 Setting up the display for music, videos,and photosConnect the display to a local area network (LAN) via the LAN port as shown in the following illustration andset up the network settings. The display only supports wired network connection. After making a physicalconnection, a small number of networks may require the display network settings to be adjusted. For mostnetworks, the display will connect automatically without any adjustments.For detail information, check your router manual.CAUTION: Do not connect a modular phone cable to the LAN port.Since there are various connection methods, please follow the specifications of your telecommunicationcarrier.To set up the network settings (if your display connected automatically, running setup again will not disruptthe connection):1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to NETWORK and press OK.3. Press the Navigation buttons to select Network Setting and press OK.4. If you already set Network Setting, select Resetting. The new connection settings resets the currentnetwork settings.5. Select IP Auto Setting or IP Manual Setting.46 Chapter 8   Setting up the display for music, videos, and photos
●If selecting IP Manual Setting, press the Navigation and Number buttons. IP addresses will need tobe input manually.●IP Auto Setting: Select this if there is a DHCP (Dynamic Host Configuration Protocol) server(router) on the local area network (LAN) via wired connection, the display will automatically beallocated an IP address. If you’re using a broadband router that has a DHCP server function, the IPaddress will automatically be determined.6. When you are finished, press EXIT.CAUTION: The network setting menu will not be available until the display is connected to a physicalnetwork.Since there are various connection methods, HP recommends that you follow the specifications of yourtelecommunication carrier.NOTE: If you want to access the Internet directly on your display, the internet connection should always beon.If you cannot access the Internet, check the network conditions from a computer on your network.When you use Network Setting, check the LAN cable or check if DHCP in the router is turned on.If you do not complete the network settings, the network may not work properly.Tips for network setting●Use a standard LAN cable with this display. Use a Cat5 or better with a RJ45 connector.●Many network connection problems during set up can often be fixed by resetting the router. Afterconnecting the display to the network, quickly power off and/or disconnect the power cable of thenetwork router. Then power on and/or connect the power cable again.●HP is not responsible for any malfunction of the display and/or the internet connection feature due tocommunication errors/malfunctions associated with your internet connection, or other connectedequipment.●HP is not responsible for problems within your internet connection.●You may experience undesired results if the network connection speed does not meet the requirementsof the content being accessed.●Some internet connection operations may not be possible due to certain restrictions associated withyour Internet connection●Any internet fees, including connection charges, without limitation, are your responsibility.●A 10 Base-T or 100 Base-TX LAN port is required when using a wired connection to this display. If yourinternet service does not allow for such a connection, you will not be able to connect the display.47
Network status1. Press MENU to access the main menus.2. Press the Navigation buttons to scroll to NETWORK and press OK.3. Press the Navigation buttons to select Network Status.4. Press OK to check the network status.5. When you are finished, press EXIT.Option DescriptionSetting Return to the network setting menu.Test Test the current network status after setting the network.Close Return to the previous menu.Connecting USB storage devicesYou can use USB flash memory devices for content playback and multimedia features in the USB built-inplayer.Connect a USB flash memory or USB memory card reader to the display as shown on the followingillustration. The My media screen appears.CAUTION: Do not turn the display off or remove a USB storage device while the EMF (My media) menu isactivated, as this could result in loss of files or damage to the USB storage device.Back up your files saved on a USB storage device frequently, as you may lose or damage the files and thismay be not covered by the warranty.Tips for using USB storage devices●Only a USB storage device is recognizable.●If the USB storage device is connected through a USB hub, the device is not recognizable.●A USB storage device using an automatic recognition program may not be recognized.●A USB storage device that uses its own driver will not be recognized.48 Chapter 8   Setting up the display for music, videos, and photos
●The recognition speed of a USB storage device may depend on each device.●Do not turn off the display or unplug the USB device when the connected USB storage device is working.When such a device is suddenly separated or unplugged, the stored files or the USB storage device maybe damaged.●Only use a USB storage device that has normal music files, image files or video files.●Use only a USB storage device that was formatted as a FAT32 file system, NTFS file system by with theWindows operating system. In case of a storage device formatted with a different utility program that isnot supported by Windows, it may not be recognized.●Connect power to a USB storage device (over 0.5 A) that requires an external power supply. If not, thedevice may not be recognized.●Connect a USB storage device with the cable included by the device maker.●Some USB storage devices may not be supported or operate smoothly.●File alignment method of USB storage devices can recognize up to 100 English characters.●Be sure to back up important files since data stored on a USB memory device may be damaged. We willnot be responsible for any data loss.●If the USB HDD does not have an external power source, the USB device may not be detected. So be sureto connect the external power source. Please use a power adaptor for an external power source.●If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use upto 4 partitions or USB memory devices.●If a USB memory device is connected to a USB multi-card reader, its volume data may not be detected.●If the USB memory device does not work properly, disconnect and reconnect it.●How fast a USB memory device is detected differs from device to device.●If the USB is connected in Standby Mode, that drive will automatically be loaded when the display isturned on.●The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USBmemory.●Any device with more than the recommended capacity may not work properly.●If a USB external hard disk with a “Energy Saving” function does not work, turn the hard disk off and onagain to make it work properly.●USB storage devices below USB 2.0 are supported as well. But they may not work properly with videos.●A maximum of 999 folders or files can be recognized under one folder.●It is recommended you use a certified USB storage device and cable. Otherwise, a USB storage devicemay not be detected or a playback error may occur.●A USB 3.0 storage device may not work.Connecting USB storage devices 49
Browsing filesAccess the photo, music, or video lists and browse files.1. Connect a USB storage device.2. Press MENU to access the main menus.3. Press the Navigation buttons to scroll to My Media and press OK.4. Press the Navigation buttons to choose from Movie List, Photo List, or Music List and press OK.Item Description(1) Moves to upper level folder.(2) Current page/Total pages.(3) Corresponding buttons on the remote control.(4) Current page/total pages of contents under the folder focused on (1).(5) Contents under the folder focused on (1).Button DescriptionGreen button Press the green button to toggle between Photo List > Music List, Music List > Movie List or Movie List >Photo List.Yellow button A method to view as either large thumbnail folder or listing.Blue button Convert to Mark Mode.50 Chapter 8   Setting up the display for music, videos, and photos
Supported file formatType Supported file formatMovie DAT,MPG,MPEG,VOB,AVI,MP4,MKV,TS,T RP,TP,ASF,WMV,FLV)Movie (*.mpg/*.mpeg/*dat/*.ts/*.trp/*.tp/*.vob/*. mp4/*.mov/*.mkv/*.avi/*.asf/*.wmv/*.flv/*. avi(motion-jpeg)/*. mp4(motion-jpeg)/*.mkv(motion-jpeg))supporting fileVideo format : Xvid1.00, Xvid1.01, Xvid1.02, Xvid1.03, Xvid1.10 beta-1/beta-2, Mpeg-1, Mpeg-2, Mpeg-4, H.264/AVC, VC1, JPEG, Sorenson H.263Audio format : Dolby Digital, AAC, Mpeg, MP3, LPCM, HE-AAC, ADPCM, WMABit rate : within 32 kbps to 320 kbps(MP3)External Subtitle format : *.smi/*.srt/*.sub (MicroDVD,Subviewer1.0/2.0)/*.ass/*.ssa/*. txt(TMPlayer)/*Internal Subtitle format : only, XSUBPhoto JPEG Baseline : 64 x 64 to 15360 x 8640Progressive : 64 x 64 to 1920 x 1440●You can play JPEG files only●Non-supported files are displayed in the form of predefined icon.File extensions: .jpg, .jpeg, .jpeSupported file format:●SOF0: baseline●SOF1: Extend Sequential●SOF2: ProgressivePhoto size:●Min: 64 x 64●Max: Normal●Type: 15360 (W) x 8640 (H)●Progressive Type: 1920 (W) x 1440 (H)Music MP3Bit rate 32 to 320●Sampling rate MPEG1 Layer3 : 32 kHz, 44.1 kHz, 48 kHz●Sampling rate MPEG2 Layer3 : 16 kHz, 22.05 kHz, 24 kHz●Sampling rate MPEG2.5 Layer3 : 8 kHz, 11.025 kHz, 12 kHzContent File Extensions : *.cts/ *.cseMovieFile Extensions: *.mpg/*.mpeg/*.dat/*.ts/*. trp/*.tp/*.vob/*.mp4/*.mov/*.mkv/*.avi/*.asf/*. wmv/*.avi(motion JPEG)/*.mp4(motion JPEG)/*. mkv(motion JPEG)Video format: MPEG1, MPEG2, MPEG4,H.264/ AVC, Xvid 1.00,Xvid 1.01, Xvid 1.02, Xvid 1.03,Xvid 1.10-beta1/2, JPEG, VC1(WVC1/WMV3)Audio format: MP2,MP3,Dolby Digital, LPCM, AAC, HE-AAC,LPCM, ADPCM, WMA, MP3Photo: JPEG JPG PNG BMPSupported file format:Browsing files 51
●SOF0: baseline●SOF1: Extend Sequential●SOF2: ProgressivePhoto size:●Min: 64 x 64●Max: 136 x 768Music: MP3Bit rate: 32 kbps to 320 kbpsSampling rate:●32 kHz, 44.1 kHz, 48 kHz (MPEG1 L3)●16 kHz, 22.05 kHz, 24 kHz (MPEG2 L3)●8kHz, 11.025 kHz, 12 kHz (MPEG2.5 L3)Playing videosYour display shows all of the video files saved in a USB storage device or shared folder on a computer.1. Press the Navigation buttons to scroll to My Media and press OK.2. Press the Navigation buttons to scroll to Movie List and press OK.3. Press the Navigation buttons to scroll to a folder you want and press OK.4. Press the Navigation buttons to scroll to a file you want and press OK.Menu DescriptionPlay marked Returns to the selected video file.Mark All Mark all video files on the screen.Unmark All Deselect all marked video files.Exit Mark Mode Exit the Mark Mode.5. Play a video.NOTE: Non-supported files are displayed in the preview image by icon only  .Abnormal files are displayed in the form of a bitmap  .6. Control playback by using the following buttons.Button DescriptionStops the playback.Plays a video.Pauses or resumes the playback.Scans backward in a file.52 Chapter 8   Setting up the display for music, videos, and photos
Scans forward in a file.MENU Show the Option menu.Hide the menu on the full-sized screen.Return to Movie List.< or >Skips to specific points in a file during playback. The time of a specific point will appear on the status bar. In somefiles, this function may not work properly.Press the ENERGY SAVING button repeatedly to increase the brightness of your screen.Tips for playing video files●Some user-created subtitles may not work properly.●Some special characters are not supported in subtitles.●HTML tags are not supported in subtitles●Subtitles in languages other than the supported languages are not available.●The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audiolanguage is changed.●A damaged video file may not be played correctly, or some player functions may not be usable.●Video files produced with some encoders may not be played correctly.●If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.●HD videos with a maximum of 1920x1080@25/30P or 1280x720@50/60P are supported, depending onthe frame.●Videos with resolutions higher than 1920X1080@25/30P or 1280x720@50/60P may not work properlydepending on the frame.●Video files other than the specified types and formats may not work properly.●Max bitrate of playable video file is 20 Mbps. (only, Motion JPEG : 10 Mbps).●We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/ AVC.●DTS Audio codec is not supported.●A video file more than 30 GB in file size is not supported for playback.●A video file name and its subtitle file name must be identical for it to be displayed.●Playing a video via a USB connection that does not support high speed may not work properly●Files encoded with GMC (Global Motion Compensation) may not be played.●When you are watching the video by Movie List function, you can adjust an image by Energy Saving keyon the remote control.Video options1. Press MENU to access the Pop-Up menus.2. Press the Navigation buttons to scroll to Set Video Play, Set Video. or Set Audio and press OK.Playing videos 53
NOTE: Option values changed in Movie List do not affect Photo List and Music List.Option value changed in Photo List and Music List are changed likewise in Photo List and Music Listexcluding Movie List.When replaying the video file after stopping, you can play from where it stopped previously.When you select Set Video Play:1. Press the Navigation buttons to scroll to show the Picture Size, Audio Language, Subtitle Language orRepeat.2. Press the Navigation buttons to scroll to make appropriate adjustments.Menu DescriptionPicture Size Selects your desired picture format during video play.Audio Language Changes the Language Group of the audio during video play. This option cannot be selected for files with asingle audio track.Subtitle Language Turn on/off the subtitle.Language Activated for SMI subtitle and can select the language within the subtitle.Code Page Can select the font for subtitle. When set to default, same font as general menu will be used.Sync Adjusts the time synchronization of the subtitle from -10 secs to +10 secs by steps of 0.5 secs during videoplay.Position Changes the position of the subtitle either up or down during video play.Size Selects your desired Subtitle size during video play.Repeat Turn on/off repeat function of video playback. When turned on, the file within the folder will be played backrepeatedly. Even when the repeated playback is turned off, it can run the playback if the file name is similarto the previous file.Code Page DescriptionLatin1 English, Spanish, French, German, Italian, Swedish, Finnish, Dutch, Portuguese, Danish, Romanian,Norwegian, Albanian, Gaelic, Welsh, Irish, Catalan,ValencianLatin2 Bosnian, Polish, Croatian, Czech, Slovak, Slovenian, Serbian, HungarianLatin4 Estonian, Latvian, LithuanianCyrillic Bulgarian, Macedonian, Russian, Ukrainian, KazakhGreek GreekTurkish TurkishKorean Korean54 Chapter 8   Setting up the display for music, videos, and photos
NOTE: Only 10,000 sync blocks are supported within the subtitle file.When playing a video, you can adjust the Picture Size by pressing the ARC button.Subtitles in your language are only supported when the OSD menu is also in this language.The code page options may be disabled depending on the language of the subtitle files.Select the appropriate code page for the subtitle files.When you select Set Video:▲Press the Navigation buttons to scroll to make appropriate adjustments.When you select Set Audio:1. Press the Navigation buttons to scroll to show the Sound Mode, Clear Voice II, or Balance.2. Press the Navigation buttons to scroll to make appropriate adjustments.Viewing photosView image files saved in a USB storage device. The displays on the screen may differ from the model.1. Press the Navigation buttons to scroll to My Media and press OK.2. Press the Navigation buttons to scroll to Photo List and press OK.3. Press the Navigation buttons to scroll to a folder you want and press OK.4. Press the Navigation buttons to scroll to a file you want and press OK.Menu DescriptionView marked Display the selected photo file.Mark All Mark all photo files on the screen.Unmark All Deselect all marked photo files.Exit Mark Mode Exit the Mark Mode.5. View photos.NOTE: Non-supported files are displayed the preview image by icon only.Abnormal files are displayed in bitmap form.Using photo optionsUse the following options while viewing photos.Option DescriptionSlideshow Starts or stops a slideshow with selected photos. If there are no selected photos, all photos saved in the currentfolder display during a slideshow. To set a slideshow speed, select Option.BGM Turns the background music (BGM) on or off. To set the background music folder, select Option. You can adjustOption by MENU button on the remote control.Rotates photos clockwise (90°, 180°, 270°, 360°).NOTE: The supported photo size is limited. You cannot rotate a photo if the resolution of the rotated width islarger than the supported resolution size.Viewing photos 55
View the photo by zoom in 2, 4 times.NOTE: Photos with a resolution of 960x540 or less cannot be enlarged.Press the ENERGY SAVING button repeatedly to change the brightness of your screen.MENU ●Slide Speed: Selects a slideshow speed (Fast, Medium, Slow).●TransitionEffect: Set the view mode of the slideshow.●BGM: Selects a music folder for the background music.NOTE: You cannot change the music folder while the background music is playing.You can only select the MP3 folder saved on the device that currently displays the photo.Hides the option window. To display the options, press OK.Return to Photo List.Photo options1. Press MENU to show the Option menus.2. Press the Navigation buttons to scroll to Set Photo View, Set Video. or Set Audio and press OK.NOTE: Option values changed in Movie List do not affect Photo List and Music List.Option value changed in Photo List and Music List are changed likewise in Photo List and Music Listexcluding Movie List.When replaying the video file after stopping, you can play from where it stopped previously.When you select Set Photo View:1. Press the Navigation buttons to scroll to show the Slide Speed, Transition Effect, or BGM.2. Press the Navigation buttons to scroll to make appropriate adjustments.Transition Effect OptionOption DescriptionSliding Pushes the current slide out of view as it plays to the next slide.Stairs Pushes the current slide in a staircase shape as it plays to the next slide.Door Open/Close Pushes the current slide like opening or closing the door as it plays to the next slide.Shutter Pushes the current slide like drawing or pulling down the blind as it plays to the next slide56 Chapter 8   Setting up the display for music, videos, and photos
Fade In Fades the slide out slowly before playing to the next slide.When you select Set Video:▲Press the Navigation buttons to scroll to make appropriate adjustments.When you select Set Audio:1. Press the Navigation buttons to scroll to show the Sound Mode, Clear Voice II, or Balance.2. Press the Navigation buttons to scroll to make appropriate adjustments.Listening to musicNOTE: Speakers must be installed on the display to listen to audio.1. Press the Navigation buttons to scroll to My Media and press OK.2. Press the Navigation buttons to scroll to Music List and press OK.3. Press the Navigation buttons to scroll to a folder you want and press OK.4. Press the Navigation buttons to scroll to a file you want and press OK.Menu DescriptionPlay marked Display the selected music file.Mark All Mark all music files on the screen.Unmark All Deselect all marked music files.Exit Mark Mode Exit the Mark Mode.5. Play music.6. Control playback by using the following buttons.Button DescriptionStops playing back the file and moves back to the music list.Plays a music file.Pauses or resumes playback.Skips to the previous file.Skips to the next file.orWhen playing, when you press the << button, the previous music file will be played. When you press the >>button, the next music file will be played.Listening to music 57
GreenbuttonStart playing the selected music files and then move to the Music List.Press the ENERGY SAVING button repeatedly to increase the brightness of your screen.MENU Show the Option menu.Hides the option window. To display the options, press OK.When you press the EXIT button while the Music player is displayed, only the music will be stopped and theplayer will not return to normal viewing. When you press the EXIT button while the music is stopped or while themusic player is hidden, the player will return to normal viewing.< or >When using the < or > button during playback a cursor indicating forward or backward.Tips for playing music files●This display does not support the ID3 Tag embedded MP3 files.NOTE: Non-supported files are displayed in the preview image by icon only  .Abnormal files are displayed as bitmaps  .A damaged or corrupted music does not play but displays 00:00 in playtime.A music downloaded from a paid service with copyright protection does not start but displays inappropriateinformation in playtime.If you press OK or ( ) buttons, audio and screen saver is stopped.The PLAY ( ), Pause ( ), ,( ), ( ) buttons on the remote control are also available in this mode.You can use the ( ) button to select the next music and the ( ) button to select the previous music.Music options1. Press MENU to access the Pop-Up menus.2. Press the Navigation buttons to scroll to Set Audio Play or Set Audio and press OK.NOTE: Option values changed in Movie List do not affect Photo List and Music List.Option value changed in Photo List and Music List are changed likewise in Photo List and Music Listexcluding Movie List.When you select Set Audio Play:1. Press the Navigation buttons to scroll to show Repeat or Random.2. Press the Navigation buttons to scroll to make appropriate adjustments.When you select Set Audio:1. Press the Navigation buttons to scroll to show the Sound Mode, Clear Voice II, or Balance.2. Press the Navigation buttons to scroll to make appropriate adjustments.58 Chapter 8   Setting up the display for music, videos, and photos
Using PIP/PBPDisplays videos or photos stored in a USB device on a single display by dividing it into the main and subscreens.1. Press the MENU button to move to OPTION and press OK.2. Press PIP/PBP to select PIP or PBP and then press OK.3. Select Movie List or Photo List from My Media. (With PIP/PBP selected, the Music List is deactivated.)4. Select a file you want and then press OK.Using PIP/PBP 59
5. Select the PIP or PBP icon from the play list.6. Select either Main or Sub for sound. You must select the output sound before running the PIP or PBPfunction.7. The sub screen is displayed on the main screen.60 Chapter 8   Setting up the display for music, videos, and photos
9 TroubleshootingNo image is displayed.Cause SolutionIs the product power cord connected? See if the power cord is properly connected to the outlet.Does the 'Out of range' message appear? The signal from the computer (video card) is out of the vertical orhorizontal frequency range of the product. Adjust the frequencyrange using the following specifications:Maximum resolution RGB : 1920 x 1080 @ 60 HzHDMI/DisplayPort : 1920 x 1080 @ 60 HzDoes the 'Check signal cable' message appear? The signal cable between computer and product is not connected.Check the signal cable.Press the INPUT menu in the remote Control to check the inputsignal.'Unknown Product' message appears when the product is connected.Cause SolutionDid you install the driver? See if the plug & play function is supported by referring to thevideo card user manual.The screen image looks abnormal.Cause SolutionIs the screen position wrong? D-Sub analog signal - Press the AUTO button in the remotecontrol to automatically select the optimal screen status that fitsinto the current mode. If adjustment is not satisfactory, use thePosition OSD menu.See if the video card resolution and frequency are supported bythe product. If the frequency is out of range, set to therecommended resolution in the Control Panel Display Settingmenu.Do thin lines appear on the background screen? D-Sub analog signal - Press the AUTO button in the remotecontrol to automatically select an optimal screen status that fitsinto the current mode. If adjustment is not satisfactory, use theClock OSD menu.Horizontal noise appears or the characters look blurred. D-Sub analog signal - Press the AUTO button in the remotecontrol to automatically select an optimal screen status that fitsinto the current mode. If adjustment is not satisfactory, use thePhase OSD menu.The screen is displayed abnormally. The proper input signal is not connected to the signal port.Connect the signal cable that matches with the source inputsignal.61
After-image appears on the product.Cause SolutionAfter-image appears when the product is turned off. If you use a fixed image for a long time, the pixels may bedamaged quickly. Use the screen-saver function.When a dark image is displayed on the screen after an image withhigh contrast (black and white or gray), this may cause imagesticking. This is normal for LCD screen.The audio function does not work.Cause SolutionNo sound? See if the audio cable is connected properly.Adjust the volume.See if the sound is set properly.Sound is too dull. Select the appropriate equalize sound.Sound is too low. Adjust the volume.Screen color is abnormal.Cause SolutionScreen has poor color resolution (16 colors). Set the number of colors to more than 24 bits (true color) SelectControl Panel - Display - Settings - Color Table menu in Windows.Screen color is unstable or mono-colored. Check the connection status of the signal cable. Or, reinsert thecomputer video card.Do black spots appear on the screen? Several pixels (red, green, white or black color) may appear onthe screen, which can be attributable to the unique characteristicsof the LCD panel. It is not a malfunction of the LCD.The operation does not work normally.Cause SolutionThe power suddenly turned off. Is the sleep timer set?Check the power control settings. Power interrupted.62 Chapter 9   Troubleshooting
10 Specifications42-inch modelsLCD Panel Screen type 1064.67 mm Wide (42 inch) TFT (Thin Film Transistor) LCD (LiquidCrystal Display) Panel.Visible diagonal size : 1064.67 mmPixel pitch 0.4833 mm (H) x 0.4833 mm (V)Video Signal Max resolution RGB : 1920 x 1080 @ 60 HzHDMI/ DisplayPort : 1920 x 1080 @ 60 HzIt may not be supported depending on the OS or video card type.Recommended resolution RGB : 1920 x 1080 @ 60 HzHDMI/ DisplayPort : 1920 x 1080 @ 60 HzIt may not be supported depending on the OS or video card type.Horizontal frequency 30 kHz to 83 kHzVertical frequency 50 Hz to 60 HzSynchronization type Separate Sync, Composite Sync, DigitalInput connector 15-pin D-Sub type, HDMI (digital), Component, RS-232C, LAN,DisplayPort, USBPower Rated voltage AC 100-240 V~ 50/60 Hz 1.3 APower consumption On Mode : 90 W TypSleep Mode (if WOL is off) : ≤ 0.5 WSleep Mode (if WOL is on) : ≤ 2.0 WOff Mode : ≤ 0.5 WEnvironmentalconditionsOperating TemperatureOperating Humidity0°C to 40°C10% to 80%Storage TemperatureStorage Humidity-20°C to 60°C5% to 95%Dimensions W x H x D, weight)(no stand or speakers)962.2 mm x 560.8 mm x 77 mm37.88 in x 22.08 in x 3.03 in12.8 kg28.22 lbs  (stand, no speakers) 962.2 mm x 636.5 mm x 297.7 mm37.88 in x 25.06 in x 11.72 in14.1 kg31.09 lbs42-inch models 63
  (no stand, with speakers) 962.2 mm x 560.8 mm x 100.1 mm37.88 in x 22.08 in x 3.94 in13.55 kg29.87 lbs  (with stand and speakers) 962.2 mm x 636.5 mm x 297.7 mm37.88 in x 25.06 in x 11.72 in14.1 kg31.09 lbsFor models that support speakers:Audio RMS Audio Output 10 W + 10 W (R + L)Input Sensitivity 0.7 VrmsSpeaker Impedance 8 Ω64 Chapter 10   Specifications
DimensionsNOTE: Product specifications may change without prior notice due to upgrade of product functions.4-M6 wall mounting screwsDepth 10.0 mm (Max)42-inch models 65
47-inch modelsLCD Panel Screen type 1192.78 mm Wide (47 inch) TFT (Thin Film Transistor) LCD (LiquidCrystal Display) Panel.Visible diagonal size : 1192.78 mmPixel pitch 0.5415 mm (H) x 0.5415 mm (V)Video Signal Max resolution RGB : 1920 x 1080 @ 60 HzHDMI/ DisplayPort : 1920 x 1080 @ 60 HzIt may not be supported depending on the OS or video card type.Recommended resolution RGB : 1920 x 1080 @ 60 HzHDMI/ DisplayPort : 1920 x 1080 @ 60 HzIt may not be supported depending on the OS or video card type.Horizontal frequency 30 kHz to 83 kHzVertical frequency 50 Hz to 60 HzSynchronization type Separate Sync, Composite Sync, DigitalInput connector 15-pin D-Sub type, HDMI (digital), Component, RS-232C, LAN,DisplayPort, USBPower Rated voltage AC 100-240 V~ 50/60 Hz 1.3 APower consumption On Mode : 95 W TypSleep Mode (if WOL is off) : ≤ 0.5 WSleep Mode (if WOL is on) : ≤ 2.0 WOff Mode : ≤ 0.5 WEnvironmentalconditionsOperating TemperatureOperating Humidity0°C to 40°C10% to 80%Storage TemperatureStorage Humidity-20°C to 60°C5% to 95%Dimensions W x H x D, weight)(not including stand orspeakers)1074.3 mm x 624 mm x 78.6 mm42.3 in x 24.57 in x 3.10 in15.5 kg34.17 lbs  (with stand, no speakers) 1074.3 mm x 699.9 mm x 298.3 mm42.3 in x 27.56 in x 11.74 in16.8 kg37.03 lbs  (no stand, with speakers) 1074.3 mm x 624 mm x 101.6 mm42.3 in x 24.57 in x 4.0 in16.25 kg66 Chapter 10   Specifications
35.83 lbs  (with stand, and speakers) 1074.3 mm x 699.9 mm x 298.3 mm42.3 in x 27.56 in x 11.74 in17.55 kg38.69 lbsFor models that support speakers:Audio RMS Audio Output 10 W + 10 W (R + L)Input Sensitivity 0.7 VrmsSpeaker Impedance 8 Ω47-inch models 67
DimensionsNOTE: Product specifications may change without prior notice due to upgrade of product functions.Dimensions4-M6 wall mounting screwsDepth 20.0 mm (Max)68 Chapter 10   Specifications
Recognizing preset display resolutionsThe display resolutions listed below are the most commonly used modes and are set as factory defaults. Thisdisplay automatically recognizes these preset modes and they will appear properly sized and centered on thescreen.Preset Pixel format Horizontal Frequency (Hz) Vertical Frequency (Hz)1 640 x 480 31.469 59.940*2 720 x 400 31.469 70.0873 800 x 600 37.879 60.3174 1024 x 768 48.363 60.0045 1280 x 720 45.000 60.0006 1280 x 800 49.702 59.8107 1280 x 1024 63.981 60.0208 1440 x 900 55.469 59.9019 1600 x 900 60.000 60.00010 1680 x 1050 65.290 59.95411 1920 x 1080 67.5 60.00*RGB mode onlyRecognizing preset display resolutions 69
DTV modeResolution Component HDMI/DisplayPort (DTV)480i o x576i o x480p o o576p o o720p o o1080i o o1080p o oNOTE: HDMI/DisplayPort input mode may identified in PC resolution: 640 x 480 / 60 Hz, 1280 x 720 / 60 Hz,1920 x 1080 / 60 Hz or DTV resolutions: 480p, 720p, 1080p.NOTE: Vertical frequency: To enable the user to watch the product display, screen image should bechanged tens of times every second like a fluorescent lamp. The vertical frequency or refresh rate is thetimes of image display per second. The unit is Hz.Horizontal frequency: The horizontal interval is the time to display one vertical line. When 1 is divided by thehorizontal interval, the number of horizontal lines displayed every second can be tabulated as the horizontalfrequency. The unit is kHz.IR codesAll models do not support the HDMI/USB function.Some key codes are not supported depending on the model.Code (Hexa) Function Note95 Energy Saving R/C BUTTON08  POWER R/C BUTTON (ON/OFF)0B INPUT R/C BUTTONC4 Display On R/C BUTTONC5 Display Off R/C BUTTON43 MENU R/C BUTTON40 UP (∧) R/C BUTTON41 Down (∨) R/C BUTTON07 Left (<) R/C BUTTON06 Right (>) R/C BUTTON44 OK R/C BUTTON28 BACK  R/C BUTTON70 Chapter 10   Specifications
5B EXIT R/C BUTTON4D PSM R/C BUTTON02 Volume (+) R/C BUTTON03 Volume (-) R/C BUTTON09 MUTE R/C BUTTONE0 Bright ^ (Page Up) R/C BUTTONE1 Bright v (Page Down) R/C BUTTON10 to 19 Number key 0 to 9 R/C BUTTON72 Red key (ID ON) R/C BUTTON71 Green key (ID OFF) R/C BUTTON63 Yellow key R/C BUTTON61 Blue key R/C BUTTON7B TILE R/C BUTTON76 ARC (4:3) R/C BUTTON77 ARC (16:9) R/C BUTTONAF ARC (ZOOM) R/C BUTTON79 ARC (MARK) R/C BUTTON99 Auto config R/C BUTTONB1 R/C BUTTONB0 R/C BUTTONBA R/C BUTTON8F R/C BUTTON8E R/C BUTTONIR codes 71
11 Agency regulatory noticesFederal Communications Commission noticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant toPart 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and the receiver.●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.●Consult the dealer or an experienced radio or television technician for help.ModificationsThe FCC requires the user to be notified that any changes or modifications made to this device that are notexpressly approved by Hewlett Packard Company may void the user's authority to operate the equipment.CablesConnections to this device must be made with shielded cables with metallic RFI/EMI connector hoods tomaintain compliance with FCC Rules and Regulations.Declaration of Conformity for products marked with the FCClogo (United States only)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference.2. This device must accept any interference received, including interference that may cause undesiredoperation.For questions regarding the product, contact:Hewlett Packard CompanyP. O. Box 692000, Mail Stop 530113Houston, Texas 77269-2000Or, call 1-800-HP-INVENT (1-800 474-6836)For questions regarding this FCC declaration, contact:Hewlett Packard Company72 Chapter 11   Agency regulatory notices
P. O. Box 692000, Mail Stop 510101Houston, Texas 77269-2000Or, call (281) 514-3333To identify this product, refer to the Part, Series, or Model number found on the product.Canadian noticeThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing EquipmentRegulations.Avis CanadienCet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleurdu Canada.European Union regulatory noticeProducts bearing the CE marking comply with the following EU Directives:●Low Voltage Directive 2006/95/EC●EMC Directive 2004/108/EC●Ecodesign Directive 2009/125/EC, where applicableCE compliance of this product is valid if powered with the correct CE-marked AC adapter provided by HP.Compliance with these directives implies conformity to applicable harmonized European standards(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or productfamily and available (in English only) either within the product documentation or at the following web site:www.hp.eu/certificates (type the product number in the search field).The compliance is indicated by one of the following conformity markings placed on the product:  For non-telecommunications products and for EU harmonizedtelecommunications products, such as Bluetooth® withinpower class below 10mW.For EU non-harmonized telecommunications products (Ifapplicable, a 4-digit notified body number is inserted betweenCE and !).Please refer to the regulatory label provided on the product.The point of contact for regulatory matters is: Hewlett-Packard GmbH, Dept./MS: HQ-TRE, HerrenbergerStrasse 140, 71034 Boeblingen, GERMANY.Canadian notice 73
German ergonomics noticeHP products which bear the “GS” approval mark, when forming part of a system comprising HP brandcomputers, keyboards and monitors that bear the “GS” approval mark, meet the applicable ergonomicrequirements. The installation guides included with the products provide configuration information.Japanese noticeKorean noticePower cord set requirementsThe display power supply is provided with Automatic Line Switching (ALS). This feature allows the display tooperate on input voltages between 100–120V or 200–240V.The power cord set (flexible cord or wall plug) received with the display meets the requirements for use in thecountry where you purchased the equipment.If you need to obtain a power cord for a different country, you should purchase a power cord that is approvedfor use in that country.The power cord must be rated for the product and for the voltage and current marked on the product'selectrical ratings label. The voltage and current rating of the cord should be greater than the voltage andcurrent rating marked on the product. In addition, the cross-sectional area of the wire must be a minimum of0.75 mm² or 18 AWG, and the length of the cord must be between 6 feet (1.8 m) and 12 feet (3.6 m). If youhave questions about the type of power cord to use, contact an authorized HP service provider.A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it oragainst it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exitsfrom the product.Japanese power cord requirementsFor use in Japan, use only the power cord received with this product.CAUTION: Do not use the power cord received with this product on any other products.74 Chapter 11   Agency regulatory notices
Product environmental noticesMaterials disposalThis HP product contains mercury in the fluorescent lamp in the display LCD that might require specialhandling at end-of-life.Disposal of this material can be regulated because of environmental considerations. For disposal or recyclinginformation, contact the local authorities or the Electronic Industries Alliance (EIA) www.eiae.org.Disposal of waste equipment by users in private households in the European UnionThis symbol on the product or on its packaging indicates that this product must not be disposed of with yourhousehold waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to adesignated collection point for the recycling or waste electrical and electronic equipment. The separatecollection and recycling of your waste equipment at the time of disposal will help to conserve naturalresources and ensure that it is recycled in a manner that protects human health and the environment. Formore information about where you can drop off your waste equipment for recycling, please contact the localcity office, the household waste disposal service or the shop where you purchased the product.Chemical substancesHP is committed to providing our customers with information about the chemical substances in our productsas needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006 of the EuropeanParliament and Council). A chemical information report for this product can be found at www.hp.com/go/reach.HP recycling programHP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeablebatteries. For more information about recycling programs, go to www.hp.com/recycle.Restriction of Hazardous Substances (RoHS)A Japanese regulatory requirement, defined by specification JIS C 0950, 2005, mandates that manufacturersprovide Material Content Declarations for certain categories of electronic products offered for sale after July1, 2006. To view the JIS C 0950 material declaration for this product, visit www.hp.com/go/jisc0950.Product environmental notices 75
11363-200611363-2006Turkey EEE regulationIn Conformity with the EEE RegulationEEE Yönetmeliğine UygundurUkraine Restriction of Hazardous SubstancesОбладнання відповідає вимогам Технічного регламенту щодо обмеження використання деякихнебезпечних речовин в електричному та електронному обладнані, затвердженого постановою КабінетуМіністрів України від 3 грудня 2008 № 1057.The equipment complies with requirements of the Technical Regulation, approved by the Resolution ofCabinet of Ministry of Ukraine as of December 3, 2008, in terms of restrictions for the use of certaindangerous substances in electrical and electronic equipment.76 Chapter 11   Agency regulatory notices
12 Controlling multiple productsUse this method to connect several products to a single computer. You can control several products at a timeby connecting them to a single computer.In the Option menu, Set ID must be between 1 and 255 without being duplicated.Connecting the cableConnect the RS-232C cable as shown.The RS-232C protocol is used for communication between the computer and product. You can turn theproduct on/off, select an input source or adjust the OSD menu from your computer.RS-232C configurationsConnecting the cable 77
Communication parameterBaud Rate: 9600 baud Rate (UART)Data Length: 8 bitParity Bit: NoneStop Bit: 1 bitFlow Control: NoneCommunication Code: ASCII codeUse a crossed (reverse) cableCommand reference list Command Data (Hexadecimal)1201. Power k a 00 to 0102. Input Select x b Refer to ‘Input Select’03. Aspect Ratio k c Refer to ‘Aspect Ratio’04. Energy Saving j q Refer to ‘Energy Saving’05. Picture mode d x Refer to ‘Picture Mode’06. Contrast k g 00 to 6407. Brightness k h 00 to 6408. Sharpness k k 00 to 6409. Color k I 00 to 6410. Tint k j 00 to 6411. Color Temperature x u 00 to 6412. H Position f q 00 to 6413. V Position f r 00 to 6414. H Size f s 00 to 6415. Auto configuration j u 0116. Balance k t 00 to 6417. Sound mode d y Refer to ‘Sound Mode’18. Treble k r 00 to 6419. Bass k s 00 to 6420. Speaker d v 00 to 0121. Volume Mute k e 00 to 0122. Volume Control k f 00 to 6478 Chapter 12   Controlling multiple products
23. Time 1 (Years/Months/Days) f a Refer to ‘Time 1’24. Time 2 (Hours/Minutes/Seconds) f x Refer to ‘Time 2’25. Off Timer (Repeat mode/Time) f e Refer to ‘Off Timer’26. On Timer (Repeat mode/Time) f d Refer to ‘On Timer’27. On Timer Input f u Refer to ‘On Timer Input’28. Sleep Time f f 00 to 0829. Power On Delay f h 00 to 6430. Automatic Standby m n 00 to 0131. Auto Off f g 00 to 0132. Language f I Refer to ‘Language’33. ISM Mode j p Refer to ‘ISM Method’34. Auto-Switch Select m I 00H to 02H35. Auto-Switch Input Select m j Refer to ‘Auto-Switch Input Select.’36. Reset f K 00 to 0337. Tile Mode d d 00 to FF38. Tile Mode Check d z FF39. Tile ID d I Refer to ‘Tile ID’40. Tile H Position d e 00 to 3241. Tile V Position d f 00 to 3242. Tile H Size d g 00 to 3243. Tile V Size d h 00 to 3244. Natural Mode (In Tile mode) d j 00 to 0145. DPM Select f j 00 to 0146. Temperature Value d n FF47. Remote Lock/Key Lock k m 00 to 0148. Key m c Refer to ‘Key’49. OSD Select k l 00 to 0150. Elapsed Time Return d l FF51. Serial No. Check f y FF52. S/W Version f z FF53. White Balance Red Gain j m 00 to FE54. White Balance Green Gain j n 00 to FE55. White Balance Blue Gain j o 00 to FE56. Backlight m g 00 to 64Command reference list 79
NOTE: During USB operations such as EMF, all commands except Power(k a) and Key(m c) are not executedand treated as NG.Transmission / Receiving protocolTransmission[Command1][Command2][ ][Set ID][ ][Data][Cr]* [Command1]: First command to control the set.* [Command2]: Second command to control the set.* [Set ID]: Set ID with which you want to communicate. Enter [Set ID] = ‘00(0x00’ to communicate with all setsregardless of their Set ID numbers.* [Data]: Information passed to the set.* [Data1]: Information passed to the set.* [Data2]: Information passed to the set.* [Data3]: Information passed to the set.* [Cr]: Carriage Return. ASCII code ‘0x0D’.* [ ]: ASCII code space ‘0x20’Acknowledgement[Command2][ ][Set ID][ ][OK/NG][Data][x]* When the product receives data normally, it sends an acknowledgement (ACK) in the format above. If data isin read mode, it indicates the data that shows the current status. If data is in read mode, it simply indicatesthe data that is sent from the computer.* If a command is sent with Set ID '00' (=0x00), the data is reflected to all display and they do send anacknowledgement (ACK).* If the data value 'FF' is sent in control mode via RS-232C, the current setting value of a function can bechecked (only for some functions).* Some commands are not supported depending on the model.01. Power (Command: k a)To control the Power On/Off the display.Transmission[k][a][ ][Set ID][ ][Data][Cr]Data00 : Off01 : OnAcknowledgement[a][ ][Set ID][ ][OK/NG][Data][x]80 Chapter 12   Controlling multiple products
* Only when the display is fully powered on, the Acknowledgement signal is returned properly. * There maybe a certain time of delay between the Transmission and Acknowledgement signals.02. Input Select (Command: x b)To select the Input Source for display.Transmission[x][b][ ][Set ID][ ][Data][Cr]Data20: Input (AV)40: Component60: RGB70: VOE(PC)80: VOE(DTV)90: HDMI(HDMI1)(DTV)A0: HDMI(HDMI1)(PC)C0: Display Port(DTV)D0: Display Port(PC)91: HDMI2/SDI(DTV)A1: HDMI2/SDI(PC)Acknowledgement[b][ ][Set ID][ ][OK/NG][Data][x]*Some input signals may not be supported depending on the model.03. Aspect Ratio (Command: k c)To adjust the screen format.Transmission[k][c][ ][Set ID][ ][Data][Cr]Data01: 4:304: Zoom09: Just scan (720p or more)(Component, HDMI/ Display Port DTV)* RGB, HDMI/Display Port PC mode(1:1)10 to 1F: Cinema Zoom 1 to 16(AV, Component, HDMI DTV)Transmission / Receiving protocol 81
* Available data types differ depending on the input signal. For more information, see the aspect ratio sectionof this guide.* The aspect ratio may differ depending on the model's input configuration.Acknowledgement[c][ ][Set ID][ ][OK/NG][Data][x]04. Energy Saving (Command: j q)To set the Energy Saving function.Transmission[j][q][ ][Set ID][ ][Data][Cr]Data00: Off01: Minimum02: Medium03. Maximum04: Auto05. Screen OffAcknowledgement[q][ ][Set ID][ ][OK/NG][Data][x]** It may not be supported depending on the model.05. Picture Mode (Command: d x)To select the Picture Mode.Transmission[d][x][ ][Set ID][ ][Data][Cr]Data00: Vivid01: Standard02: Cinema03. Sport04: GameAcknowledgement[x][ ][Set ID][ ][OK/NG][Data][x]06. Contrast (Command: k g)To adjust the screen contrast.Transmission82 Chapter 12   Controlling multiple products
[k][g][ ][Set ID][ ][Data][Cr]Acknowledgement[g][ ][Set ID][ ][OK/NG][Data][x]07. Brightness (Command: k h)To adjust the screen brightness.Transmission[k][h][ ][Set ID][ ][Data][Cr]Data00 to 64: Brightness 0 to 100Acknowledgement[h][ ][Set ID][ ][OK/NG][Data][x]08. Sharpness (Command: k k)To adjust the screen sharpness.* This function is available only in AV/Component input.Transmission[k][k][ ][Set ID][ ][Data][Cr]Data00 to 64: Sharpness 0 to 100Acknowledgement[k][ ][Set ID][ ][OK/NG][Data][x]09. Color (Command: k i)To adjust the screen color.* This function is available only in AV/Component input.TransmissionData[k][i][ ][Set ID][ ][Data][Cr]00 to 64: Color 0 to 100Acknowledgement[i][ ][Set ID][ ][OK/NG][Data][x]10. Tint (Command: k j)To adjust the screen tint.* This function is available only in AV/Component input.TransmissionTransmission / Receiving protocol 83
[k][j][ ][Set ID][ ][Data][Cr]Data00 to 64: Tint R50 to G50Acknowledgement[j][ ][Set ID][ ][OK/NG][Data][x]11. Color Temperature (Command: x u)To adjust the screen Color Temperature.Transmission[x][u][ ][Set ID][ ][Data][Cr]Data00 to 64: Warm 50 to Cool 50Acknowledgement[u][ ][Set ID][ ][OK/NG][Data][x]12. H Position (Command: f q)To adjust the screen Horizontal Position.* This function is available only when the Tile Mode is set to Off.* The operational range varies depending on the RGB input resolution (Only available for RGB-PC input.)Transmission[f][q][ ][Set ID][ ][Data][Cr]Data00 to 64: min. -50 (Left) to max. 50 (Right)Acknowledgement[q][ ][Set ID][ ][OK/NG][Data][x]13. V Position (Command: f r)To adjust the screen Vertical Position.* This function is available only when the Tile Mode is set to Off.* The operational range varies depending on the RGB input resolution (Only available for RGB-PC input.)Transmission[f][r][ ][Set ID][ ][Data][Cr]Data00 to 64: min. -50 (Bottom) to max. 50 (Top)Acknowledgement[r][ ][Set ID][ ][OK/NG][Data][x]84 Chapter 12   Controlling multiple products
14. H Size (Command: f s)To adjust the screen Horizontal Size.* This function is available only when the Tile Mode is set to Off.* The operational range varies depending on the RGB input resolution (Only available for RGB-PC input.)Transmission[f][s][ ][Set ID][ ][Data][Cr]Data00 - 64: Min. -50 (Reduce) - Max. 50 (Expand)Acknowledgement[s][ ][Set ID][ ][OK/NG][Data][x]15. Auto Configuration (Command: j u)To adjust the picture position and minimize image shaking automatically.(Only available for RGB-PC input.)Transmission[j][u][ ][Set ID][ ][Data][Cr]Data01 : SetAcknowledgement[u][ ][Set ID][ ][OK/NG][Data][x]16. Balance (Command: k t)To adjust the sound balance.Transmission[k][t][ ][Set ID][ ][Data][Cr]Data00 to 64: Left 50 to Right 50Acknowledgement[t][ ][Set ID][ ][OK/NG][Data][x]17. Sound Mode (Command: d y)To adjust the sound mode.Transmission[d][y][ ][Set ID][ ][Data][Cr]Data01: StandardTransmission / Receiving protocol 85
02: Music03: Cinema04: Sport05. GameAcknowledgement[y][ ][Set ID][ ][OK/NG][Data][x]18. Treble (Command: k r)To adjust the Treble values.Transmission[k][r][ ][Set ID][ ][Data][Cr]Data00 to 64: Treble 0 to 100Acknowledgement[r][ ][Set ID][ ][OK/NG][Data][x]19. Bass (Command: k s)To adjust the Bass values.Transmission[k][s][ ][Set ID][ ][Data][Cr]Data00 to 64: Bass 0 to 100Acknowledgement[s][ ][Set ID][ ][OK/NG][Data][x]20. Speaker (Command: d v)To select the speaker on/off.Transmission[d][v][ ][Set ID][ ][Data][Cr]Data00: Off01: OnAcknowledgement[v][ ][Set ID][ ][OK/NG][Data][x]21. Volume Mute (Command: k e)To control the Volume Mute on/off.86 Chapter 12   Controlling multiple products
Transmission[k][e][ ][Set ID][ ][Data][Cr]Data00 : Mute (Volume Off)01 : Current volume (Volume On)Acknowledgement[e][ ][Set ID][ ][OK/NG][Data][x]22. Volume Control (Command: k f)To set the playback volume.Transmission[k][f][ ][Set ID][ ][Data][Cr]Data00 to 64: Volume 0 to 100Acknowledgement[f][ ][Set ID][ ][OK/NG][Data][x]23. Time 1(Year/ Month/ Day) (Command: f a)To set the Time 1(Year/ Month/ Day) values.Transmission[f][a][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]Data100 to 14: 2010 to 2030Data201 to 0C: January to DecemberData301 to 1F: 1 to 31* Enter “fa [Set ID] ff” for checking Time 1(Year/ Month/ Day) values.Acknowledgement[a][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]24. Time 2(Hour/ Minute/ Second) (Command: f x)To set the Time 2(Hour/ Minute/ Second) values.Transmission[f][x][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]Data100 to 17: 00 to 23 hoursTransmission / Receiving protocol 87
Data200 to 3B: 00 to 59 minutesData300 to 3B: 00 to 59 seconds* Enter “fx [Set ID] ff” for checking Time 2(Hour/ Minute/ Second) values.** This command won’t work if Time 1(Year/ Month/ Day) has not been set in advance.Acknowledgement[x][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]25. Off Timer(Repeat Mode/ Time) (Command: f e)To set the Off Timer(Repeat Mode/ Time) function.Transmission[f][e][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]Data11. f1h to f7h (Read data)F1: Read the 1st Off Time dataF2: Read the 2nd Off Time dataF3: Read the 3rd Off Time dataF4: Read the 4th Off Time dataF5: Read the 5th Off Time dataF6: Read the 6th Off Time dataF7: Read the 7th Off Time data2. e1h-e7h (Delete one index), e0h (Delete all indexes)E0: Delete all Off Time dataE1: Delete the 1st Off Time dataE2: Delete the 2nd Off Time dataE3: Delete the 3rd Off Time dataE4: Delete the 4th Off Time dataE5: Delete the 5th Off Time dataE6: Delete the 6th Off Time dataE7: Delete the 7th Off Time data3. 01h to 06h (Set the day of week for Off Time)00: Off01: Once02. Daily88 Chapter 12   Controlling multiple products
03: Monday to Friday04: Monday to Saturday05: Saturday to Sunday06. Sunday07. Monday08. Tuesday09. Wednesday0A. Thursday0B. Friday0C. SaturdayData200 to 17: 00 to 23 HoursData300 to 3B: 00 to 59 Minutes* To read or delete the Off Time list, set FFH for [Data2] and [Data3].(Example 1: fe 01 f1 ff ff - Read the 1st Off Time data.)(Example 2: fe 01 e1 ff ff - Delete the 1st Off Time data.)(Example 3: fe 01 04 02 03 - Set the Off Time to "Monday to Saturday, 02:03".)* This function is supported only when 1 (Year/Month/ Day) and 2 (Hour/Minute/Second) are set.Acknowledgement[e][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]26. On Timer(Repeat Mode/ Time) (Command: f d)To set the On Timer(Repeat mode/ Time) function.Transmission[f][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]Data11. f1h to f7h (Read data)F1: Read the 1st On Time dataF2: Read the 2nd On Time dataF3: Read the 3rd On Time dataF4: Read the 4th On Time dataF5: Read the 5th On Time dataF6: Read the 6th On Time dataF7: Read the 7th On Time dataTransmission / Receiving protocol 89
2. e1h-e7h (Delete one index), e0h (Delete all indexes)E0: Delete all Off Time dataE1: Delete the 1st On Time dataE2: Delete the 2nd On Time dataE3: Delete the 3rd On Time dataE4: Delete the 4th On Time dataE5: Delete the 5th On Time dataE6: Delete the 6th On Time dataE7: Delete the 7th On Time data3. 01h to 06h (Set the day of week for On Time)00: Off01: Once02. Daily03: Monday to Friday04: Monday to Saturday05: Saturday to Sunday06. Sunday07. Monday08. Tuesday09. Wednesday0A. Thursday0B. Friday0C. SaturdayData200 to 17: 00 to 23 HoursData300 to 3B: 00 to 59 Minutes* To read or delete the On Time list, set FFH for [Data2] and [Data3].(Example 1: fe 01 f1 ff ff - Read the 1st On Time data.)(Example 2: fe 01 e1 ff ff - Delete the 1st On Time data.)(Example 3: fe 01 04 02 03 - Set the On Time to "Monday to Saturday, 02:03".)* This function is supported only when 1 (Year/Month/ Day) and 2 (Hour/Minute/Second) are set.Acknowledgement[e][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]90 Chapter 12   Controlling multiple products
27. On Timer Input (Command: f u)To select an external input for the current On Time setting and add a new schedule or change the existingschedule.Transmission[f][u][ ][Set ID][ ][Data1][Cr][f][u][ ][Set ID][ ][Data1][Data2][Cr]Data (Add schedule)20: Input (AV)40: Component60. RGB90: HDMI (HDMI1)C0: Display Port91: HDMI2/SDIData1 (Change schedule)1. f1h to f4h (Read data)F1: Select the 1st schedule inputF2: Select the 2nd schedule inputF3: Select the 3rd schedule inputF4: Select the 4th schedule inputF5: Select the 5th schedule inputF6: Select the 6th schedule inputF7: Select the 7th schedule inputData220: Input (AV)40: Component60. RGB90: HDMI (HDMI1)C0: Display Port91: HDMI2/SDI* To read the schedule input, enter FFH for [Data2].(Example 1: fu 01 60 - Move each schedule input down one row and save the 1st schedule input in RGBmode.)(Example 2: fu 01 f1 ff - Read the 1st schedule input.)(Example 3: fu 01 f3 20 - Change the 3rd data schedule input to the current On Time and AV input.)* This function is supported only when 1 (Year/Month/ Day), 2 (Hour/Minute/Second), On Time (Repeat Mode/Time) are set.Transmission / Receiving protocol 91
** It may not be supported depending on the model.Acknowledgement[u][ ][Set ID][ ][OK/NG][Data][x][u][ ][Set ID][ ][OK/NG][Data1][Data2][x]28. Sleep Time (Command: f f)To set the Sleep Time.Transmission[f][f][ ][Set ID][ ][Data][Cr]Data00: Off (Sleep Timer off)01: 10 min.02: 20 min.03: 30 min.04: 60 min.05: 90 min.06: 120 min.07: 180 min.08: 240 min.Acknowledgement[f][ ][Set ID][ ][OK/NG][Data][x]29. Power On Delay (Command: f h)To set the schedule delay when the power is turned on. (Unit: Second)Transmission[f][h][ ][Set ID][ ][Data][Cr]Data00 to 64: min. 0 to max. 100 (sec.)Acknowledgement[h][ ][Set ID][ ][OK/NG][Data][x]30. Automatic Standby (Command: m n)To set the Automatic Standby function.Transmission[m][n][ ][Set ID][ ][Data][Cr]Data00: Off (No off after 4 hours)92 Chapter 12   Controlling multiple products
01: 4 Hours (Off after 4 hours)Acknowledgement[n][ ][Set ID][ ][OK/NG][Data][x]31. Auto Off (Command: f g)To set the Auto Off function.Transmission[f][g][ ][Set ID][ ][Data][Cr]Data00: Off (No off after 15 minutes)01: 15 min.(Off after 15 minutes)Acknowledgement[g][ ][Set ID][ ][OK/NG][Data][x]32. Language (Command: f i)To set the language for OSD.Transmission[f][i][ ][Set ID][ ][Data][Cr]Data00: Czech01: Danish02: German03: English04: Spanish (EU)05: Greek06: French07: Italian08: Dutch09: Norwegian0A: Portuguese0B: Portuguese (BR)0C: Russian0D: Finnish0E: Swedish0F: Korean10: Chinese (Mandarin)Transmission / Receiving protocol 93
11: Japanese12: Yue Chinese (Cantonese)Acknowledgement[i][ ][Set ID][ ][OK/NG][Data][x]33. ISM mode (Command: j p)To select ISM method for avoiding having a fixed image remain on screen.Transmission[j][p][ ][Set ID][ ][Data][Cr]Data01: Inversion02: Orbiter04: White Wash08. NormalAcknowledgement[p][ ][Set ID][ ][OK/NG][Data][x]34. Auto-Switch Input Select (Command: m i)To set the Auto-Switch Input function.Transmission[m][i][ ][Set ID][ ][Data][Cr]Data00: Off01: Auto02: ManualAcknowledgement[i][ ][Set ID][ ][OK/NG][Data][x]35. Auto-Switch Input Select (Command: m j)To select the input source for auto switch.* This command is only available when the Auto-Switch Input (auto) mode is set to Custom.Transmission[m][j][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr] [ ][Data4][ ][Data5][Cr]Data1 to 5 (Priority 1 to 5)60: RGB90: HDMI(HDMI1)94 Chapter 12   Controlling multiple products
C0: Display Port91: HDMI2/SDI* The number of data items differs depending on the model.Acknowledgement[j][ ][SetID][ ][OK/NG][Data1][Data2][Data3][Data4] [ ][Data5][x]36. Reset (Command: f k)To execute the Picture, Screen, Audio and Factory reset function.Transmission[f][k][ ][Set ID][ ][Data][Cr]Data00: Picture Reset01: Screen Reset02: Factory Reset03: Audio ResetAcknowledgement[k][ ][Set ID][ ][OK/NG][Data][x]37. Tile Mode (Command: d d)To set a Tile Mode and Tile Column/ Row values.Transmission[d][d][ ][Set ID][ ][Data][Cr]Data00 to FF: 1st byte - Tile Row2nd byte - Tile Column*00, 01, 10, 11 means Tile Mode Off.Acknowledgement[d][ ][Set ID][ ][OK/NG][Data][x]** It may not be supported depending on the model.38. Tile Mode Check (Command: d z)To check Tile Mode status.Transmission[d][z][ ][Set ID][ ][Data][Cr]DataFF: Check Tile Mode status.** It may not be supported depending on the model.Transmission / Receiving protocol 95
Acknowledgement[z][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]Data1 00: Tile Mode Off01: Tile Mode OnData2 00 to 0F: Tile RowData3 00 to 0F: Tile Column39. Tile ID (Command: d i)To set Tile ID.Transmission[d][i][ ][Set ID][ ][Data][Cr]Data01 to E1: Tile ID 01 to 225**FF: Check Tile ID** Data could not be set over (Tile Column) x (Tile Row).** It may not be supported depending on the model.Acknowledgement[i][ ][Set ID][ ][OK/NG][Data][x]*NG will be return if data is over (Tile Column) x (Tile Row), except 0xFF.40. Tile H Position (Command: d e)To adjust the Tile Horizontal position.* This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode setto On.Transmission[d][e][ ][Set ID][ ][Data][Cr]Data00 to 32: -50 (Left) to 0 (Right)*Left/Right values depend on Tile H size.** It may not be supported depending on the model.Acknowledgement[e][ ][Set ID][ ][OK/NG][Data][x]41. Tile V Position (Command: d f)To adjust the Tile Vertical position.* This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode setto On.96 Chapter 12   Controlling multiple products
Transmission[d][f][ ][Set ID][ ][Data][Cr]Data0 to 32: 0 (Bottom) to 50 (Top)* Bottom/Top values depend on Tile Vertical size.** It may not be supported depending on the model.Acknowledgement[f][ ][Set ID][ ][OK/NG][Data][x]42. Tile H Size (Command: d g)To adjust the Tile Horizontal size.*Set Tile H Position to 0x32 before setting Tile H Size.* This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode setto On.Transmission[d][g][ ][Set ID][ ][Data][Cr]Data00 to 32: 0 to 50Acknowledgement[g][ ][Set ID][ ][OK/NG][Data][x]43. Tile V Size (Command: d h)To adjust the Tile Vertical size.*Set Tile V Position to 0x00 before setting Tile V Size.* This function is available only when the Natural option of the Tile Mode is set to Off while the Tile Mode setto On.Transmission[d][h][ ][Set ID][ ][Data][Cr]Data00 to 32: 0 to 50** It may not be supported depending on the model.Acknowledgement[h][ ][Set ID][ ][OK/NG][Data][x]44. Natural Mode (In Tile Mode) (Command : d j)To display the image naturally, the part of the image that would normally be displayed in the gap betweenthe displays is omitted.TransmissionTransmission / Receiving protocol 97
[d][j][ ][Set ID][ ][Data][Cr]Data00: Off01: OnAcknowledgement[j][ ][Set ID][ ][OK/NG][Data][x]45. DPM Select (Command: f j)To set the DPM (Display Power Management) function.Transmission[f][j][ ][Set ID][ ][Data][Cr]Data00: Off01: OnAcknowledgement[j][ ][Set ID][ ][OK/NG][Data][x]46. Temperature Value (Command: d n)To check the inside temperature value.Transmission[d][n][ ][Set ID][ ][Data][Cr]DataFF: Check the statusAcknowledgement[n][ ][Set ID][ ][OK/NG][Data][x]* Temperature is displayed in hexadecimal.47. Remote Controller Lock/ Key Lock (Command: k m)When the remote control and front keys are locked in standby mode, the power cannot be turned on usingthe remote control or front power button.Transmission[k][m][ ][Set ID][ ][Data][Cr]Data00: Off (Lock Off)01: On (Lock On)* Display will not be turned on by power on key of remote controller and front panel control keys, if key islocked on in standby mode.98 Chapter 12   Controlling multiple products
Acknowledgement[m][ ][Set ID][ ][OK/NG][Data][x]48. Key (Command: m c)To send a key code of the IR remote control.Transmission[m][c][ ][Set ID][ ][Data][Cr]DataIR_KEY_CODEAcknowledgement[c][ ][Set ID][ ][OK/NG][Data][x]For a key code, see the IR Code.* Some key codes are not supported depending on the model.49. OSD Select (Command: k l)To select OSD (On Screen Display) on/off.Transmission[k][l][ ][Set ID][ ][Data][Cr]Data00: Off01: OnAcknowledgement[l][ ][Set ID][ ][OK/NG][Data][x]50. Elapsed time return (Command: d l)To check the panel used time.Transmission[d][l][ ][Set ID][ ][Data][Cr]DataFF: Read the statusAcknowledgement[l][ ][Set ID][ ][OK/NG][Data][x]* Returned data means used hours in hexadecimal.51. Serial No.Check (Command: f y)To check the Serial Numbers.TransmissionTransmission / Receiving protocol 99
[f][y][ ][Set ID][ ][Data][Cr]DataFF: Check the product Serial NumberAcknowledgement[y][ ][Set ID][ ][OK/NG][Data][x]* Data is ASCII code.52. S/W Version (Command: f z)To check the Software Version.Transmission[f][z][ ][Set ID][ ][Data][Cr]DataFF: Check the Software versionAcknowledgement[z][ ][Set ID][ ][OK/NG][Data][x]53. White Balance Red Gain (Command: j m)To set the White Balance Red Gain.Transmission[j][m][ ][Set ID][ ][Data][Cr]Data00 to FE: Red Gain 0 to 254Acknowledgement[m][ ][Set ID][ ][OK/NG][Data][x]54. White Balance Green Gain (Command: j n)To set the White Balance Green Gain.Transmission[j][n][ ][Set ID][ ][Data][Cr]Data00 to FE: Green Gain 0 to 254Acknowledgement[n][ ][Set ID][ ][OK/NG][Data][x]55. White Balance Blue Gain (Command: j o)To set the White Balance Blue Gain.Transmission100 Chapter 12   Controlling multiple products
[j][o][ ][Set ID][ ][Data][Cr]Data00 to FE: Blue Gain 0 to 254Acknowledgement[o][ ][Set ID][ ][OK/NG][Data][x]56. Backlight (Command: m g)To adjust the screen backlight.Transmission[m][g][ ][Set ID][ ][Data][Cr]Data00 to 64: Backlight 0 to 100Acknowledgement[g][][set ID][][OK/NG][Data][x]** It may not be supported depending on the model.Transmission / Receiving protocol 101

Navigation menu