LG Electronics USA IPS206TX LCD Monitor User Manual ENG E2 50V IP100105

LG Electronics USA LCD Monitor ENG E2 50V IP100105

IPS206TX_User manual

www.lg.comOWNER’S MANUALLCD MONITOR LCD MONITOR MODELIPS206TPlease read this manual carefully before operating your set and retain it for future reference.ENGLISH
1This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The power supply cord is used as the main disconnection device. Ensure that thesocket-outlet is easily accessible after installation.Operate the display only from a power source indicated in the specifications of thismanual or listed on the display. If you are not sure what type of power supply youhave in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call yourservice technician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display. To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock. Important Precautions
2Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not place thedisplay where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchen sink,laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity.
Important Precautions3On CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water or otherliquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining. On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.On Disposal The fluorescent lamp used in this product contains a small amount of mercury.Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
Important PrecautionsNOTETHE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTRERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY NOTEThis epuipment has been tested and found to comply with the limits for a class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequencycause harmful interference to radio communications.However,there is noguarantee that interference will not occur in a particular installation.If this which can be determined by turning the equipment off and on,the user isencouraged to try to correct the interference by one or more of the followingmeasures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and the receiver.-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.energy and,if not installed and used in accordance with the instructions,may equipment does cause harmful interference to radio or television reception,TO OPERATE THE EQUIPMENT. -Consult the dealer or an experienced radio/TV technician for help.A3
4Accessories!!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.DVI-D Signal Cable(This feature is not available inall countries.)NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferritecores to maintain standard compliance for the product.User's Guide/CardsPower Cord AC-DC adapter(Depending on the country)AC-DC adapter(Depending on the country)Screws15-pin D-Sub Signal Cable(To set it up, this signal cable maybe attached to this product beforeshipping out.)Or
Connecting the Display5Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off.Connecting and Disassembling the stand1. Place the monitor with its front facing downward on a soft cloth.2. Use a coin on the back of the stand base and turn the screw clockwise to tighten.3. Once assembled take the monitor up carefully and face the front side.4. When you desire to disintegrate the monitor from the stand base, use a coin to turn thescrew counterclockwise.ImportantThis illustration depicts the general model of connection. Your monitor may differ fromthe items shown in the picture.Do not carry the product upside down holding only the stand base. The product mayfall and get damaged or injure your foot.
6Connecting the DisplayBefore setting up the monitor, ensure that the power to the monitor,the computer system, and other attached devices is turned off. Positioning your displayAfter installation, adjust the angle as shown below. * With stand base Adjust the position of the panel in various ways for maximum comfort.Tilt Range : -5˚ to 15˚ ERGONOMICIt is recommended that in order to maintain an ergonomic and comfortable viewing position,the forward tilt angle of the monitor should not exceed 5 degrees.Do not touch or press the screen whenadjusting the angle of the monitor. When adjusting the angle of the screen, donot put your finger(s) in between the head ofthe monitor and the stand body. You canhurt your finger(s).
7Connecting the DisplayABConnect DVI-D(Digital signal) CableConnect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computersystem, and other attached devices is turned off. 2.Connect signal input cable and power cord in order, then tighten the screwof the signal cable. Connecting with the PC 12Mac adapter : For Apple Macintosh use, aseparate plug adapter is needed to change the15 pin high density (3 row) D-sub VGAconnector on the supplied cable to a 15 pin 2row connector.When using a D-Sub signal input cable connectorfor Macintosh NOTE This is a simplified representation of the rear view.This rear view represents a general model; your display maydiffer from the view as shown.Connect the signal input cable and tightenit up by turning in the direction of the arrow as shown in the figure.DC-IN/ D-SUBDVI-D电源输入PCPCABWall-outlet typeWall-outlet typeORDC-IN/电源输入 D-SUBDVI-D
8Connecting the DisplayNOTE‘ Self Image Setting Function’? This function provides the user with optimal displaysettings.When the user connects the monitor for the first time, this function automatically adjuststhe display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screenflicker or tilted screen while using the device or after changing screen resolution, press theAUTO function button to improve resolution. 3. Press the power button on the front panel to turn the power on. When monitor power isturned on, the 'Self Image Setting Function' is executed automatically.(Only Analog Mode)Power ButtonConnecting with the PC
9Control Panel FunctionsFront Panel ControlsSMART+ ButtonUse this button to enter ORIGINAL RATIO, DUALWEB,CINEMA MODE menus.For more information, refer to page 19~20.MENU ButtonOSD LOCKED/UNLOCKEDThis function allows you to lock the current controlsettings, so that they cannot be inadvertently changed.Press and hold the MENU button for several seconds.The message "OSD LOCKED" should appear.You can unlock the OSD controls at any time by pushingthe MENU button for several seconds. The message"OSD UNLOCKED" should appear.MODE ButtonFor more information, refer to page 21~22.
10Control Panel FunctionsAUTO ButtonAUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always pressthe AUTO button before entering the On ScreenDisplay(OSD). (Only Analog Mode)This will automatically adjust your display image tothe ideal settings for the current screen resolutionsize (display mode).The best display mode isIPS206T : 1600 x 900INPUT ButtonUse this button to turn the display on or off.The power indicator stays blue if the display is runningproperly (On Mode). If the display is in Sleep Mode(Energy Saving), the power indicator is blinking blue.Power Button &Power IndicatorWhen two input signals at least are connected, you canselect the input signal (D-SUB/DVI) you want. Whenonly one signal is connected, it is automatically detected.The default setting is D-Sub. (SOURCE Hot key)Exit the OSD(On Screen Display).EXIT Button Use this button to select source from input.
11On Screen Display (OSD) Control AdjustmentScreen AdjustmentMaking adjustments to the image size, position and operatingparameters of the display is quick and easy with the On ScreenDisplay Control system. A short example is given below to familiarize you with the use of thecontrols. The following section is an outline of the availableadjustments and selections you can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the discretionary Button, then the main menu of the OSD appears.To access a control, use the corresponding Buttons.Use the / Buttons to adjust the image to the desired level. Use the Button to select other sub-menu items.Press the EXIT Button to exit from the OSD. 1234
12On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus.BRIGHTNESSCONTRASTSHARPNESSPICTURE Standard image settings. : D-SUB(Analog signal) input : DVI-D(Digital signal) inputMain menu Sub-menu Supported signalsDescriptionCOLOR Color temperature adjustments.COLOR TEMPREDGREENBLUESIX COLOR (RED/GREEN/ BLUE/CYAN/MAGENTA/YELLOW)HUESATURATIONWARMMEDIUMCOOL(PRESET) (USER)LANGUAGE POWER INDICATORWHITE BALANCEFACTORY RESETTo customize the screen statusfor a user's operatingenvironmentOTHERSHORIZONTALVERTICALCLOCKPHASEGAMMACOLOR RESETDISPLAY To adjust the position of thescreen DSUBDSUBDSUBTo improve the clarity andstability of the screen DSUBDVI-DDSUBDVI-DDSUBDVI-DDSUBDVI-DDSUBDVI-D
On Screen Display(OSD) Selection and Adjustment 13NOTE The order of icons may differ depending on the model (12~22).USERMOVIETEXTPHOTOsRGBMODEIt is a mode that the screen isadjusted to the best to view thevideos.It is a mode that the screen isadjusted to the standard sRGB.It is a mode that the screen isadjusted to the best for the textworks.It is a mode that the screen isadjusted to the best to viewpictures.It is a mode that the user canadjust each element. It can adjustthe color mode of the Main Menu.ORIGINAL RATIODUAL WEBCINEMA MODESMART+ To adjust the image sizeDSUBDVI-DDSUBDVI-DMain menu Sub-menu Supported inputDescription
14On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitAdjust (Decrease/Increase)Select another sub-menuRestart to select sub-menuPress the MENU Button, then the main menu of the OSD appears.
15On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionExit : Exit: Decrease: Increase: Select another sub-menu: Restart to select sub-menuBRIGHTNESSCONTRAST SHARPNESSTo adjust the brightness of the screen. To adjust the contrast of the screen.To adjust the clearness of the screen.
16On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionCOLOR TEMPPRESET Select either PRESET or USER to adjustthe screen color. Select the preset color temperature. WARM: Yellow screen color. MEDIUM: Red screen color. COOL: Blue screen color. USERREDGREENBLUESIX COLORHUESATURATION GAMMACOLORRESETA user can create screen color byadjusting RED, GREEN and BLUE. Set your own red color levels.Sets and stores the hue and saturationfor six colors(RED/GREEN/BLUE/CYAN/MAGENTA/YELLOW) to satisfy thecolor requirements of a user. Adjusts the screen hue.Adjusts the color sharpness on thescreen. Lower values make the colorsharpness weaker and colors lighterwhile higher values make the colorsharpness stronger and colors darker. Set your own gamma value. :1.8/2.0/2.2/2.4/2.6On the monitor, high gamma valuesdisplay whitish images and low gammavalues display blackish images.Resets the color settings to the factorydefault settings for the current inputdevice. PRESET ModeUSER ModeExit : Exit: Decrease: Increase: Select another sub-menu: Restart to select sub-menuSet your own green color levels.Set your own blue color levels.
17On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionCLOCKPHASETo minimize any vertical bars orstripes visible on the screenbackground.The horizontal screen size will alsochange.To adjust the focus of the display. This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters.HORIZONTALVERTICALTo move image left and right.To move image up and down.Exit : Exit: Decrease: Increase: Select another sub-menu: Restart to select sub-menu
18On Screen Display(OSD) Selection and Adjustment Press the , buttons to resetimmediately.Main menu Sub menu DescriptionTo choose the language in which thecontrol names are displayed.LANGUAGEWHITEBALANCEIf the output of the video card isdifferent the required specifications,the color level may deteriorate dueto video signal distortion. Using thisfunction, the signal level is adjustedto fit into the standard output level ofthe video card in order to provide theoptimal image.Activate this function when whiteand black colors are present in thescreen.Restore all factory default settings except"LANGUAGE." FACTORYRESETPOWERINDICATORUse this function to set the powerindicator on the front side of the monitorto ON or OFF.If you set OFF, it will be turned off.If you set ON at any time, the powerindicator will automatically be turned on.NOTE If this does not improve the screen image, restore the factory default settings. If necessary, execute theWHITE BALANCE function again. This function will be enabled only when the input signal is an analogsignal. Exit : Exit: Decrease: Increase: Select another sub-menu: Restart to select sub-menu
19On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitMoveRestart to select sub-menuPress the SMART+ Button, then the main menu of the OSD appears.
20On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionSwitch to full screen mode according to inputimage signal.*This function works only if input resolution islower than monitor ratio (16:9).Make the eye comfortable by reducing the background brightness in the web page.* Before using below functions, please install Easy Set Packge programme.Help user to browse web efficiently by dividing in half.Help to arrange and move windows on screen.Help user to control divided windows ratio.Exit : Exit, : Move: Restart to select sub-menu
21On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.Sub-menusNOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.Menu NameIconsButtonTipExitMoveRestart to select sub-menuPress the MODE Button, then the main menu of the OSD appears.
22On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionExit : Exit, : Move: Select another sub-menuMOVIE It is a mode that the screen is adjustedto the best to view the videos.TEXTPHOTOUSERsRGB* Outside the User mode, Image(brightness,gamma) and color cannot be adjusted.It is a mode that the screen is adjustedto the best for the text works.It is a mode that the screen is adjustedto the best to view pictures.It is a mode that the user can adjusteach element. It can adjust the colormode of the Main Menu.It is a mode that the screen is adjustedto the standard sRGB.
23TroubleshootingNo image appearsCheck the following before calling for service.No image appearsDo you see a "OSD LOCKED" message on the screen?●Is the power cord of thedisplay connected?●Is the power indicatorlight on?●Is the power indicatorflickering?●Do you see an "OUT OFRANGE" message onthe screen?●Do you see a "CHECKSIGNAL CABLE"message on thescreen?• Check and see if the power cord is connectedproperly to the power outlet.• Press the Power button.• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.• Try to turn on the PC.• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED” will appear.●Do you see “OSDLOCKED” when youpush MENU button?
24TroubleshootingDisplay image is incorrect●Display Position isincorrect.●On the screenbackground, verticalbars or stripes arevisible.●Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.• Press the AUTO button to automatically adjustyour display image to the ideal setting. If the results are unsatisfactory, adjust the imageposition using the H position and V position iconin the on screen display.• Press the AUTO button to automatically adjustyour display image to the ideal setting.If the results are unsatisfactory, decrease thevertical bars or stripes using the CLOCK icon inthe on screen display.• Press the AUTO button to automatically adjustyour display image to the ideal setting.If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(true color).IMPORTANTCheck Control Panel --> Display --> Settings and see if the frequency or theresolution were changed. If yes, readjust the video card to the recommendresolution.If the recommended resolution (optimal resolution) is not selected, letters may beblurred and the screen may be dimmed, truncated or biased. Make sure to selectthe recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.
25TroubleshootingDisplay image is incorrect●The screen color ismono or abnormal.●The screen blinks.• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.• Make sure the video card is properly inserted inthe slot.• Set the color setting higher than 24 bits (true color)at Control Panel - Settings.• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.Do you see an "Unrecognized monitor, Plug&Play (VESADDC) monitor found" message?●Have you installed thedisplay driver?• Be sure to install the display driver from the displaydriver CD (or diskette) that comes with yourdisplay. Or, you can also download the driver fromour web site: http://www.lg.com.• Make sure to check if the video card supportsPlug&Play function.
28Specifications IPS206T50.8 cm (20.0 inches) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 50.8cm0.2766 x 0.2766 mm (Pixel pitch)DisplayHorizontal Freq. 30 - 83 kHz (Automatic)Vertical Freq. 56 - 75 Hz (Automatic)Input Form Separate Sync.DigitalSync InputSignal Input 15 pin D-Sub ConnectorDVI-D Connector (Digital)Input Form RGB Analog (0.7 Vp-p/ 75 ohm), DigitalVideo InputMax VESA 1600 x 900 @ 60 HzRecommend VESA 1600 x 900 @ 60 HzResolutionPlug&PlayOn Mode :28 W(Typ.)Sleep Mode ≤1 WOff Mode ≤0.5 WPowerConsumptionOperating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingEnvironmental ConditionsWith StandWidth 47.99 cm (18.89 inches) Height 38.30 cm (15.08 inches) Depth 23.00 cm ( 9.06 inches) Weight(excl. packing) 3.1 kg (6.84 lbs)Dimensions& WeightTilt : -5˚ - 15˚Range19V 2.0A Power InputAttached ( ), Detached ( O )Stand Base Wall-outlet typePower cord DDC 2B(Digital),DDC2AB(Anlaog)Without StandWidth 47.99 cm (18.89 inches) Height 31.12 cm (12.25 inches) Depth 3.99 cm ( 1.57 inches)NOTEInformation in this document is subject to change without notice.AC-DC Adapter Type PA-1650-68,manufactured by LITEON TECHNOLOGY CORP.or type EADP-40LB B,manufactured by DELTA ELECTRONICS,INC.
28SpecificationsPreset Modes (Resolution)IndicatorOn ModeSleep ModeOff ModeBlueBlue Blinking OffLED ColorMODEDisplay Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)* Recommend ModeDSUB/DVI Timing1720 x 400 31.468 702640 x 480 31.469 603640 x 480 37.500 754800 x 600 37.879 605800 x 600 46.875 7561024 x 768 48.363 6071024 x 768 60.123 7581152 x 864 67.500 75*9 1600 x 900 60.000 60
Installing the Wall mount plate29This monitor satisfies the specifications of the Wall mount plateor the interchange device.1. Place the monitor face down on the soft cloth.2. To disconnect the Stand Base from the Stand Body, unfold the screw handle andturn it to the left.3.Pull out the Stand Base to remove. 4.Remove the Stand Body.
30Installing the Wall mount plate5.Install the Wall mount plate.Wall mount plate(Separate purchase)This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for more details,which is provided when Wall mount plate ispurchased. Kensington Security SlotConnected to a locking cable thatcan be purchased separately atmost computer stores.Wall Mount pad
As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efficiency.ENERGY STAR is a set of power-saving guidelines issued by the U.S.Environmental Protection Agency(EPA).

Navigation menu