LG Electronics USA L15LM 15” Color LCD Monitor User Manual Microsoft PowerPoint F User s Manual

Download:
Mirror Download [FCC.gov]
Document ID	323449
Application ID	vTG19bA3OkGwe7CPy+4kFA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	73.2kB (915039 bits)
Date Submitted	2003-05-06 00:00:00
Date Available	2003-05-02 00:00:00
Creation Date	2003-04-30 09:14:06
Producing Software	Acrobat Distiller 5.0 (Windows)
Document Lastmod	2003-04-30 18:15:15
Document Title	Microsoft PowerPoint - F.User's Manual
Document Creator	PScript5.dll Version 5.2
Document Author:	Administrator

FCC ID : BEJL15LM
APPENDIX F :
USER’S MANUAL
Regulatory Information
FCC Compliance Statement
CE Conformity Notice (for Europe)
This equipment has been tested and found to comply within
the limits of a Class B digital device pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio
or television reception (which can be determined by turning
the equipment on and off), the user is encouraged to try to
correct the interference by using one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV
technician for help.
Caution: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's (or your) authority to operate the equipment. Only
peripherals (digital input/output devices, terminals, printers,
etc.) certified to comply with the Class B limits may be
attached to this monitor. Operation with non-certified
peripherals is likely to result in interference to radio and TV
reception.
Only shielded signal cables may be used with this System.
Products with the “CE” Marking comply with the EMC
Directive(89/336/EEC) and LOW VOLTAGE Directive
(73/23/EEC) issued by the Commission of the European
Community.
Compiance with these directives implies conformity to the
following European Norms :
• EN 55022:1998
; Radio Frequency Interference
• EN 55024:1998
; Electromagnetic Immunity
• EN 61000-3-2
; Power Line Harmonics
• EN 61000-3-3
; Voltage Fluctuations
• EN 60950
; Product Safety
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
Low Radiation Compliance (MPR II)
This monitor meets one of the strictest guidelines available
today for low radiation emissions, offering the user extra
shielding and an antistatic screen coating. These
guidelines, set forth by a government agency in Sweden,
limit the amount of emission allowed in the Extremely Low
Frequency (ELF) and Very Low Frequency (VLF)
electromagnetic range.
TCO95
Congratulations!
You have just purchased a TCO’95 approved and labelled
product! Your choice has provided you with a product
developed for professional use. Your purchase has also
contributed to reducing the burden on the environment and
to the further development of environmentally-adapted
electronic products.
Why do we have environmentally labelled computers?
In many countries, environmental labelling has become an
established method for encouraging the adaptation of
goods and services to the environment. The main problem
as far as computers and other electronic equipment are
concerned is that environmentally harmful substances are
used both in the products and during their manufacture.
Since it has not been possible so far for the majority of
electronic equipment to be recycled in a satisfactory way,
most of these potentially damaging substances sooner or
later enter Nature.
There are also other characteristics of a computer, such as
energy consumption levels, that are important from both the
working and natural environment viewpoints. Since all
types of conventional electricity generation have a negative
effect on the environment (acidic- and climatic-influencing
emissions, radioactive waste, etc.), it is vital to conserve
energy. Electronic equipment in offices consumes as
enormous amount of energy, since it is often routinely left
running continuously.
What does the environmenal labelling involve?
This product meets the requirements for the TCO’95
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
Canadian DOC Notice
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les
exigences du Règlement sur le matériel brouilleur du
Canada.
NOTICE
The regulations are applied only to the products with the
ID LABEL indicating specific requirements.
Regulatory Information cont.
scheme, which provides for international environmental
labelling of personal computers. The labelling scheme was
developed as a joint effort by the TCO (The Swedish
Confederation of Professional Employees),
Naturckyddsföreningen (The Swedish Society for Nature
Conservation), and NUTEK (The National Board for
Industrial and Technical Development in Sweden), and
SEMKO AB (an international certification agency).
The requirements cover a wide range of issues:
environment, ergonomics, usability, emission of electrical
and magnetic fields, energy consumption and electrical and
fire safety.
The environmental demands concern, among other things,
restriction on the presence and use of heavy metals,
brominated and chlorinated flame retardants, CFCs
(freons), and chlorinated solvents. The product must be
prepared for recycling, and the manufacturer is obliged to
have an environmental plan, which must be adhered to in
each country where the company implements its
operational policy.
The energy requirements include a demand that the
computer and/or display, after a certain period of inactivity,
shall reduce its power consumption to a lower level, in one
or more stages. The length of time to reactivate the
computer shall be reasonable for the user.
Labelled products must meet strict environmental
demands, for example, in respect of the reduction of electric
and magnetic fields, along with physical and visual
ergonomics and good usability.
The following is a brief summary of the environmental
requirements met by this product. The complete
environmental criteria document may be ordered from:
Lead can be found in picture tubes, display screens, solder,
and capacitors. Lead damages the nervous system and in
higher doses causes lead poisoning. The relevant bioaccumulative TCO’95 requirement permits the inclusion of
lead, as no replacement has yet been developed.
Cadmium is present in rechargeable batteries and in the
color-generating layers of certain computer displays.
Cadmium damages the nervous system and is toxic in high
doses. The relevant bio-accumulative TCO’95 requirement
states that batteries may not contain more than 25 ppm
(parts per million) of cadmium. The color-generating layers
of display screens must not contain any cadmium.
Mercury is sometimes found in batteries, relays and
switches. Mercury damages the nervous system and is
toxic in high doses. The relevant bio-accumulative TCO’95
requirement states that batteries may not contain more than
25 ppm of mercury and that no mercury is present in any of
the electrical or electronic components concerned with the
display unit.
CFCs (freons) are sometimes used for washing printed
circuit boards and in the manufacture of expanded foam for
packaging. CFCs break down ozone and thereby damage
the ozone layer in the atmosphere, causing increased
reception on Earth of ultra-violet light with consequent
increased risks of skin cancer (malignant melanoma). The
relevant TCO’95 requirement: Neither CFCs nor HCFCs
may be used during the manufacture of the product or its
packaging.
1 Bio-accumulative means that the substance accumulates
within living organisms.
Shipping Package
The packaging material can be recycled, or you can save it
to return the monitor to a service center for repair or
disposal.
CFC Compounds in Distribution Packaging
Cushioning material used for shipping finished monitors are
not manufactured with nor do they contain any CFC
compounds.
Design for Disassembly/Recycling
These monitors have been designed for easy end-of-life
disassembly and recycling. Fasteners are generally of the
same type for efficient disassembly. Components made of
different materials can be easily separated and plastics
have been identified using intermational symbols to aid in
recycling.
Monitor Disposal
TCO Development Unit
Linnegatan 14, S-11494 Stockholm, Sweden
FAX +46-8 782 92 07
E-mail (Internet): development@tco.se
Current information regarding TCO’95 approved and
labelled products may also be obtained on the Internet
using the address: http://www.tco-info.com/
TCO’95 is a co-operative project between:
NUTEK
Naturskydds
föreningen
SEMKO
Närings- och teknikutvecklingsverket
Environmental requirements
Brominated flame retardants are present in printed circuit
boards, cabling, casings, and housings, and are added to
delay the spread of fire. Up to 30% of the plastic in a
computer casing can consist of flame-retardant substances.
These are related to another group of environmental toxins,
PCBs, and are suspected of giving rise to similar harm,
including reproductive damage in fish-eating birds and
mammals. Flame retardants have been found in human
blood, and researchers fear that they can disturb fetus
development.
Bio-accumulative1 TCO’95 demands require that plastic
components weighing more than 25 grams must not
contain flame retardants with organically bound chlorine or
bromine.
WARNING
If you need to dispose of a monitor, ask a qualified service
representative for the proper procedure. Improper disposal
could result in personal injury from implosion.
Regulatory Information cont.
TCO99
The energy requirements include a demand that the
computer and/or display, after a certain period of
inactivity, shall reduce its power consumption to a
lower level in one or more stages. The length of time
to reactivate the computer shall be reasonable for
the user.
Congratulations!
You have just purchased a TCO’99 approved and
labelled product! Your choice has provided you with
a product developed for professional use. Your
purchase has also contributed to reducing the
burden on the environment and also to the further
development of environmentally adapted electronics
products.
Labelled products must meet strict environmental
demands, for example, in respect of the reduction of
electric and magnetic fields, physical and visual
ergonomics and good usability.
Below you will find a brief summary of the
environmental requirements met by this product. The
complete environmental criteria document may be
ordered from:
Why do we have environmentally labelled
computers?
In many countries, environmental labelling has
become an established method for encouraging the
adaptation of goods and services to the environment.
The main problem, as far as computers and other
electronics equipment are concerned, is that
environmentally harmful substances are used both in
the products and during their manufacture. Since it is
not so far possible to satisfactorily recycle the
majority of electronics equipment, most of these
potentially damaging substances sooner or later
enter nature.
TCO Development
SE-114 94 Stockholm, Sweden
Fax: +46 8 782 92 07
Email (Internet): development@tco.se
Current information regarding TCO’99 approved and
labelled products may also be obtained via the Internet,
using the address: http://www.tco-info.com/
Environmental requirements
Flame retardants
Flame retardants are present in printed circuit
boards, cables, wires, casings and housings. Their
purpose is to prevent, or at least to delay the spread
of fire. Up to 30% of the plastic in a computer casing
can consist of flame retardant substances. Most
flame retardants contain bromine or chloride, and
those flame retardants are chemically related to
another group of environmental toxins, PCBs. Both
the flame retardants containing bromine or chloride
and the PCBs are suspected of giving rise to severe
health effects, including reproductive damage in
fish-eating birds and mammals, due to the bioaccumulative* processes. Flame retardants have
been found in human blood and researchers fear
that disturbances in foetus development may occur.
There are also other characteristics of a computer,
such as energy consumption levels, that are
important from the viewpoints of both the work
(internal) and natural (external) environments. Since
all methods of electricity generation have a negative
effect on the environment (e.g. acidic and climateinfluencing emissions, radioactive waste), it is vital to
save energy. Electronics equipment in offices is
often left running continuously and thereby
consumes a lot of energy.
What does labelling involve?
This product meets the requirements for the TCO’99
scheme which provides for international and
environmental labelling of personal computers. The
labelling scheme was developed as a joint effort by
the TCO (The Swedish Confederation of
Professional Employees), Svenska
Naturskyddsforeningen (The Swedish Society for
Nature Conservation) and Statens Energimyndighet
(The Swedish National Energy Administration).
The relevant TCO’99 demand requires that plastic
components weighing more than 25 grams must not
contain flame retardants with organically bound
bromine or chlorine. Flame retardants are allowed in
the printed circuit boards since no substitutes are
available.
Approval requirements cover a wide range of issues:
environment, ergonomics, usability, emission of
electric and magnetic fields, energy consumption
and electrical and fire safety.
Cadmium**
Cadmium is present in rechargeable batteries and in
the colour-generating layers of certain computer
displays. Cadmium damages the nervous system
and is toxic in high doses. The relevant TCO’99
requirement states that batteries, the colourgenerating layers of display screens and the
electrical or electronics components must not contain
any cadmium.
The environmental demands impose restrictions on
the presence and use of heavy metals, brominated
and chlorinated flame retardants, CFCs (freons) and
chlorinated solvents, among other things. The
product must be prepared for recycling and the
manufacturer is obliged to have an environmental
policy which must be adhered to in each country
where the company implements its operational
policy.
Regulatory Information cont.
Mercury**
Mercury is sometimes found in batteries, relays and
switches. It damages the nervous system and is
toxic in high doses. The relevant TCO’99
requirement states that batteries may not contain
any mercury. It also demands that mercury is not
present in any of the electrical or electronics
components associated with the labelled unit.
CFCs (freons)
The relevant TCO’99 requirement states that neither
CFCs nor HCFCs may be used during the
manufacture and assembly of the product. CFCs
(freons) are sometimes used for washing printed
circuit boards. CFCs break down ozone and thereby
damage the ozone layer in the stratosphere, causing
increased reception on earth of ultraviolet light with
e.g. increased risks of skin cancer (malignant
melanoma) as a consequence.
Lead**
Lead can be found in picture tubes, display screens,
solders and capacitors. Lead damages the nervous
system and in higher doses, causes lead poisoning.
The relevant TCO’99 requirement permits the
inclusion of lead since no replacement has yet been
developed.
* Bio-accumulative is defined as substances which
accumulate within living organisms
** Lead, Cadmium and Mercury are heavy metals which are
Bio-accumulative.
EPA (U.S.A only)
ENERGYSATR is a set of power-saving guidelines
issued by the U.S. Environmental Protection
Agency(EPA).
EPA POLLUTION PREVENTER
As an ENERGY STAR Partner LG
Electronics U.S.A.,Inc. has
determined that this product meets the
ENERGY STAR guidelines for
energy efficiency.
NOM MARK (Mexico only)
GOST MARK
Internet Address:http://www.lg.ru
»ÌÙÓχˆËÓÌ̇ˇ ÒÎÛÊ·‡ LG
Electronics (095)742-77-77
BZ03
Important Precautions
This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential e shock or fire hazards.
In order to allow the proper operation of all safeguards incorporated in this
display, observe the following basic rules for its installation, use, and
servicing.
On Safety
Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.
The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.
Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.
Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.
Do not Open the Display.
There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.
To Avoid Personal Injury :
Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.
To Prevent Fire or Hazards:
Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.
A1
Important Precautions
On Installation
Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.
Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:
Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.
Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.
Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.
Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.
If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.
On Cleaning
Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display
screen because over-spraying may cause electrical shock.
On Repacking
Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.
A2
Connecting the Display
Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.
Connecting the stand base
1. Align the hooks on the stand base with the matching slots in the base of
the monitor.
2. Insert the hooks into slots.
Hook
Important
This illustration depicts the general model of connection. Your monitor may
differ from the items shown in the picture.
To Remove the Stand Base
- Do not force to remove the Stand Base, but remove the screws on the
back first for your safety.
- Once you connect the stand base, try not to disconnect it.
Do not carry the product upside down holding only
the stand base. The product may fall and get
damaged or injure your foot.
Stand Base
A3
Connecting the Display
Using the Computer
1. Connect the signal cable. When attached, tighten the thumbscrews to secure
the connection.
2. Connect the power cord into a proper power outlet that is easily accessible and
close to the display.
NOTE
This is a simplified representation of the rear view.
This rear view represents a general model; your display
may differ from the view as shown.
Signal Cable
Power Cord
Analog signal
D-sub*
* Varies according to model.
Wall-outlet type
PC-outlet type
PC
MAC
Mac adapter
For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector
on the supplied cable to a 15 pin 2 row connector.
A4
Connecting the Display
Side Jacks
*Line Out
AUDIO
IN
Speaker Out
Display
Jack of the PC sound card
Headphone/Earphone Input
Automatically mutes the speaker volume when the headphones are plugged in.
Audio Input
Connects to the *LINE OUT jack of the PC sound card.
*LINE OUT
A terminal used to connect to the speaker including a built-in amplifier (Amp). Make sure that the
connecting terminal of the PC sound card is checked before connecting. If the Audio Out of PC
sound card has only Speaker Out, reduce the PC volume.
If the Audio Out of the PC sound card supports both Speaker Out and Line Out, convert to Line
Out using the card jumper of the program (Refer to the Sound Card Manual).
A5
Control Panel Functions
Front Panel Controls
Control
Function
Power Button
Use this button to turn the display on or off.
Power (DPMS)
Indicator
This Indicator lights up green when the display
operates normally. If the display is in DPM (Energy
Saving) mode, this indicator color changes to amber.
MENU Button
Use this button to enter or exit the On Screen
Display.
Buttons
AUTO/SELECT
Button
Use these buttons to choose or adjust items in
the On Screen Display.
Use this button to enter a selection in the On Screen
Display.
A6
Control Panel Functions
Control
Direct Access Function
VOLUME:
37
Use these buttons to decrease or increase the volume level.
AUTO adjustment function
When adjusting your display settings, always press the
AUTO/SELECT button before entering the On Screen
Display(OSD). This will automatically adjust your display
image to the ideal settings for the current screen
resolution size (display mode).
PROCESSING
AUTO CONFIGURATION
The best display mode is 1024x768.
LIGHT VIEW:
This function optimizes the brightness, contrast or color
value to the surrounding conditions and settings and
enables you to enjoy the most suitable picture by
adjusting the surroundings (DAY/NIGHT/USER MODE).
• TEXT: For viewing letters
• MOVIE: For viewing movies
• PHOTO: For viewing pictures or the photographs
• USER MODE: This function memorizes the manual
adjustment -Brightness, Contrast and Color value on
the On Screen Display.
MUTE:
37
Used to select mute on (means sound off) and mute
off (means sound on).
CONTROLS LOCKED/UNLOCKED
CONTROLS LOCKED
CONTROLS UNLOCKED
: MENU and
This function allows you to secure the current control settings,
so that they cannot be inadvertently changed. Press and hold
the MENU button and
button for 3 seconds: the message
“CONTROLS LOCKED” appears.
You can unlock the OSD controls at any time by pushing the
MENU button and
button for 3 seconds:
the message “CONTROLS UNLOCKED” will appear.
A7
On Screen Display (OSD) Control Adjustment
Screen Adjustment
Making adjustments to the image size, position and operating parameters of
the display is quick and easy with the On Screen Display Control system. A
short example is given below to familiarize you with the use of the controls.
The following section is an outline of the available adjustments and selections
you can make using the OSD.
NOTE
Allow the display to stabilize for at least 30 minutes before making image adjustments.
To make adjustments in the On Screen Display, follow these steps:
MENU
AUTO/SELECT
AUTO/SELECT
MENU
Press the MENU Button, then the main menu of the OSD appears.
To access a control, use the
or
Buttons. When the icon you want
becomes highlighted, press the AUTO/SELECT Button.
Use the
Buttons to adjust the item to the desired level.
Accept the changes by pressing the AUTO/SELECT Button.
Exit the OSD by Pressing the MENU Button.
A8
On Screen Display(OSD) Selection and Adjustment
The following table indicates all the On Screen Display control, adjustment,
and setting menus.
Main menu
Sub menu
Reference
BRIGHTNESS BRIGHTNESS
CONTRAST CONTRAST
COLOR
PRESET
To adjust the brightness and
contrast of the screen
9300K
To customize the color of the
screen
6500K
R/G/B(User Color)
POSITION
V POSITION
To adjust the position of the
screen
H POSITION
TRACKING
AUDIO
CLOCK
PHASE
To improve the clarity and
stability of the screen
VOLUME
To adjust the audio function
TREBLE
BASS
BALANCE
SETUP
LANGUAGE
To customize the screen status
for a user's operating environment
OSD POSITION
FACTORY RESET
: Adjustable
NOTE
The order of icons may differ depending on the model (A9~A11).
A9
On Screen Display(OSD) Selection and Adjustment
You were introduced to the procedure of selecting and adjusting an item
using the OSD system. Listed below are the icons, icon names, and icon
descriptions of the all items shown on the Menu.
NOTE
OSD (On Screen Display) menu languages on the monitor may differ from the manual.
To adjust the brightness and contrast of the screen
OSD Adjust
Description
BRIGHTNESS / CONTRAST
BRIGHTNESS
To adjust the brightness of the screen.
88
100
CONTRAST
To adjust the contrast of the screen.
To customize the color of the screen
OSD Adjust
Description
COLOR
PRESET
9300K
6500K
RED
GREEN
BLUE
PRESET 9300K/6500K
Select the screen color.
• 9300K: Slightly bluish white.
• 6500K: Slightly reddish white.
RED
GREEN
BLUE
Set your own color levels.
To adjust the position of the screen
OSD Adjust
Description
POSITION
Vertical Position
To move image up and down.
61
39
Horizontal Position
To move image left and right.
A10
On Screen Display(OSD) Selection and Adjustment
To improve the clarity and stability of the screen
OSD Adjust
TRACKING
Description
CLOCK
To minimize any vertical bars or
stripes visible on the screen
background.The horizontal screen
size will also change.
PHASE
To adjust the focus of the display.
This item allows you to remove any
horizontal noise and clear or sharpen
the image of characters.
CLOCK
PHASE
To adjust the audio function
OSD Adjust
AUDIO
VOLUME
TREBLE
BASS
BALANCE
Description
VOLUME
To decrease or increase volume level.
TREBLE
To raises or lowers Treble level.
BASS
To raises or lowers Bass level.
BALANCE
To adjust the balance level.
To customize the screen status for a user's operating environment
OSD Adjust
Description
LANGUAGE To choose the language in which the
control names are displayed.
SETUP
LANGUAGE
ENGLISH
OSD POSITION
FACTORY RESET
NO
1024 x 768 / 60Hz
PRESET MODE
OSD POSITION To adjust position of the OSD window
on the screen.
FACTORY Return to all factory default settings
except "LANGUAGE".
RESET
If you don’t want to reset the monitor,
use the
button to select NO and
then press the AUTO/SELECT button.
A11
Troubleshooting
Check the following before calling for service.
No image appears
Is the power cord of the
display connected?
Check and see if the power cord is connected
properly to the power outlet.
Is the power indicator
light on?
Press the Power button.
Is the power on and the
power indicator green?
Adjust the brightness and the contrast.
Is the power indicator
amber?
If the display is in power saving mode, try moving
the mouse or pressing any key on the keyboard
to bring up the screen.
Make sure if the power is on.
Try to turn on the PC.
Do you see an "INPUT
SIGNAL OUT OF
RANGE" message on
the screen?
This message appears when the signal from the
PC (video card) is out of horizontal or vertical
frequency range of the display. See the
'Specifications' section of this manual and
configure your display again.
Do you see a "NO
SIGNAL "message on
the screen?
This message appears when the signal cable
between your PC and your display is not
connected. Check the signal cable and try again.
Do you see a "CONTROLS LOCKED" message on the screen?
Do you see
“CONTROLS LOCKED”
when you push MENU
button?
You can secure the current control settings,
so that they cannot be inadvertently
changed. You can unlock the OSD controls
at any time by pushing the MENU button
and
button for 3 seconds: the message
“CONTROLS UNLOCKED” will appear.
A12
Troubleshooting
Display image is incorrect
Display Position is
incorrect.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, adjust the image
position using the H position and V position
icon in the on screen display.
Check Control Panel --> Display --> Settings
and see if the frequency or the resolution were
changed. If yes, readjust the video card to the
recommend resolution.
On the screen
background, vertical
bars or stripes are
visible.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, decrease the
vertical bars or stripes using the CLOCK icon in
the on screen display.
Any horizontal noise
appearing in any
image or characters
are not clearly
portrayed.
Press the AUTO/SELECT button to
automatically adjust your display image to the
ideal setting.
If the results are unsatisfactory, decrease the
horizontal bars using the PHASE icon in the on
screen display.
Check Control Panel --> Display --> Settings
and adjust the display to the recommended
resolution or adjust the display image to the ideal
setting. Set the color setting higher than 24 bits
(true color).
The screen color is
mono or abnormal.
Check if the signal cable is properly connected
and use a screwdriver to fasten if necessary.
Make sure the video card is properly inserted in
the slot.
Set the color setting higher than 24 bits (true
color) at Control Panel - Settings.
The screen blinks.
Check if the screen is set to interlace mode and if
yes, change it to the recommend resolution.
Make sure the power voltage is high enough, It
has to be higher than AC100-240V 50/60Hz.
A13
Troubleshooting
Have you installed the display driver?
Have you installed the
display driver?
Be sure to install the display driver from the
display driver CD (or diskette) that comes with
your display. Or, you can also download the
driver from our web site: http://www.lge.com.
Do you see an
"Unrecognized monitor,
Plug&Play (VESA DDC)
monitor found"
message?
Make sure to check if the video card supports
Plug&Play function.
A14
Specifications
Display
Sync Input
Video Input
Resolution
Plug&Play
Audio
Power
Consumption
Dimensions
&Weight
(with tilt stand)
Tilt Range
Power Input
Environmental
Conditions
Tilt Stand
Signal cable
Power cord
Regulations
15 inches (38.1cm) Flat Panel Active matrix-TFT LCD
Anti-Glare coating
15 inches viewable
0.3 mm pixel pitch
Horizontal Freq. 31 - 63kHz (Automatic)
Vertical Freq.
56 - 75Hz (Automatic)
Input Form
Separate TTL, Positive/Negative
Signal Input
15 pin D-Sub Connector
Input Form
RGB Analog (0.7Vp-p/75ohm)
Max
VESA 1024 x 768@75Hz
Recommend
VESA 1024 x 768@60Hz
DDC 2B
RMS Audio Output 1W+1W(R+L)
Input Sensitivity
0.7Vrms
Speaker Impedance 4Ω
28W
Normal
Stand-by/Suspend ≤
3W
Power Off
≤
3W
Width
36.02 cm / 14.18 inches
Height
35.98 cm / 14.17 inches
Depth
15.30 cm / 6.02 inches
Net
4.15 kg (9.15 lbs)
Tilt
-5˚~30˚
AC 100-240V 50/60Hz 0.6A
Operating Conditions
Temperature 10˚C to 35 ˚C
Humidity
10 % to 80 % non-Condensing
Storage Conditions
Temperature -20˚C to 60 ˚C
Humidity
5 % to 95 % non-Condensing
Attached( ), Detached ( O )
Attached( ), Detached ( O )
Wall-outlet type or PC-outlet type
TCO99
NOTE
Information in this document is subject to change without notice.
A15
Specifications
Preset Modes (Resolution)
Display Modes (Resolution)
10
11
*12
13
14
VGA
VGA
VGA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
Horizontal Freq. (kHz)
31.468
31.468
31.469
35.000
37.861
37.500
35.156
37.879
48.077
46.875
49.725
48.363
56.476
60.023
640 x 350
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
Vertical Freq. (Hz)
70
70
60
66.67
72.8
75
56.25
60
72
75
75
60
70
75
* Recommended
Unlike CRT monitors, which require a high refresh rate to minimize flickering, TFT
technology is inherently flicker-free. If possible, configure your computer for 1024 x 768
addressability at 60Hz vertical refresh rate.
VESA wall mounting
Connected to another object (stand
type and wall-mounted type. This
monitor accepts a VESA-compliant
mounting interface pad.)
Kensington Security Slot- optional
Connected to a locking
cable that can be purchased
separately at most computer
stores
A16

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2003:04:30 09:14:06Z
Modify Date                     : 2003:04:30 18:15:15+09:00
Page Count                      : 21
Creation Date                   : 2003:04:30 09:14:06Z
Mod Date                        : 2003:04:30 18:15:15+09:00
Producer                        : Acrobat Distiller 5.0 (Windows)
Author                          : Administrator
Metadata Date                   : 2003:04:30 18:15:15+09:00
Creator                         : Administrator
Title                           : Microsoft PowerPoint - F.User's Manual

EXIF Metadata provided by EXIF.tools