LG Electronics USA L61SE2 MIB2 Entry User Manual

LG Electronics USA MIB2 Entry

User Manual

 CONFIDENTIAL not for distribution  CONFIDENTIAL not for distribution Composition Touch, CompositionColourRadioComposition Touch, Composition Colour:RadioStand: 21.08.2013Englisch: 11.2013Artikel-Nr.: 142.5R6.RCT.201425R6RCT20
 CONFIDENTIAL not for distribution  CONFIDENTIAL not for distribution Description of symbolsRefers to a section within a chapter thatcontains important information and safetynotes  that should always be observed.Indicates that the section is continued onthe next page.Indicates the end of a section.Indicates situations in which the vehiclemust be stopped as quickly as possible.® ™Indicates a registered trademark. Howev-er, the absence of this symbol does notconstitute a waiver of the rights concern-ing any term.⇒  Symbols like these refer you to warningswithin the same section or on a givenpage. They draw your attention to possi-ble risks of accident or injury and explainhow they can be avoided.⇒ ⇒ ⇒  Cross reference to information about pos-sible damage to your vehicle within thesame section or on a given page.DANGERTexts with this symbol indicate dangeroussituations which will lead to fatal or severe in-juries if you do not observe the warning.WARNINGTexts with this symbol indicate dangeroussituations which could lead to fatal or severeinjuries if you do not observe the warning.CAUTIONTexts with this symbol indicate dangeroussituations which could lead to slight or se-vere injuries if you do not observe the warn-ing.NOTICETexts with this symbol indicate situationswhich could cause damage to the vehicle or ve-hicle equipment if you do not observe thewarning.Texts with this symbol contain additional in-formation on the protection of the environ-ment.Texts with this symbol contain additional in-formation.Volkswagen AG works continuously to develop andfurther improve all models. Please understand thatwe must therefore reserve the right to alter anypart of the vehicle and its equipment or technicalspecifications at any time. The data provided con-cerning scope of delivery, appearance, perform-ance, dimensions, weights, fuel consumption,standards and vehicle functions are all correct atthe time of going to print. Some of the equipmentdescribed might not yet be available in a particularvehicle (information can be provided by your localVolkswagen dealership), and some equipment maynot be available in certain countries. No legal com-mitment may be inferred from the information, illus-trations or descriptions in this manual.No part of this manual may be reprinted, repro-duced or translated without the written permissionof Volkswagen AG.All rights under the laws of copyright are expresslyreserved by Volkswagen AG. Subject to alterationand amendment.Printed in Germany.© Volkswagen AG 2013This paper was bleached without the use ofchlorine.
FCC Compliance Statement [Level 4]  <North America>   This device complies with part 15 of the FCC Rules.    Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  against  harmful  interference  in  a  residential  installation.  This  equipment generates,  uses,  and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be  determined  by  turn-ing  the  equipment  off  and  on,  the  user  is  encouraged  to  try  to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.   • Increase the separation between the equipment and receiver. • Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.  Caution:   Any  changes  or  modifications  in  construction  of  this  device  which  are  not  expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.   <Canada>   This  Class  B  digital  apparatus  complies  with  Canadian  ICES-003  “To  prevent  radio interference to the licensed service, this device is intended to be operated indoors and away from windows to  provide  maximum  shielding. Equipment  (or  its  transmit  antenna)  that  is installed outdoors is subject to licensing.”  Cet  appareil  numérique  de  la  classe  B  est  conforme  à  la  norme  NMB-003    «Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être  utilisé  à l'intérieur et  devrait  être  placé  loin  des  fenêtres  afin de fournir  un  écran de blindage maximal. Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.»  Operation is subject to the following two conditions :   (1)  This  device  may  not  cause  Interference,  and  (2)  this  device  must  accept  any interference, including interference that may cause undesired operation of the device.
MODEL L61SE2Dimensions (mm)W272.7Dimensions (mm)H156.52Dimensions (mm)D208.52Weight (KG) 1.6Power Requirement 9V~18VPower Consumption 25W * 4CHPRODUCT SPECIFICATION
Bluetooth SpecificationStandard Bluetooth Version 2.1+EDR 2400 ~ 2483.5 MHz+4 dBm Max.Frequency RangeOutput Power (Max.)
 CONFIDENTIAL not for distribution Table of ContentsAbout this manual  . . . . . . . . . . . . . . . . 2IntroductionBefore using the unit for the first time  . . . . . 3Safety information for the infotainmentsystem  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Overview of the control elements . . . . . . . . . 6General information on operating the unit  . 7Audio modeRadio mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Media mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Telephone control (PHONE)Introduction to telephone control system  . . 30Description of telephone control system  . . 34SettingsMenu and system settings (SETUP)  . . . . . . 40Sound and volume settings . . . . . . . . . . . . . . 42Abbreviations  . . . . . . . . . . . . . . . . . . . . . 44Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Table of Contents 1142.5R6.RCT.201425R6RCT20
 CONFIDENTIAL not for distribution About this manual● An alphabetical index is included at the end ofthis manual.● A list of abbreviations explains technical abbre-viations and terms.●Directions and positions (e.g. right, left, front,rear) are normally relative to the vehicle's directionof travel.●Illustrations help with orientation and should beregarded as a general guide.● In right-hand drive vehicles the controls maysometimes be different to those displayed in illus-trations or described in the text.All equipment and models are described withoutindicating whether the equipment is optional orspecific to the model type. This means that someof the equipment described might not be fitted inyour vehicle. Your Volkswagen dealership can pro-vide more information on this.All details provided in this manual correspond tothe information available at the time of going toprint and apply only to factory-fitted infotainmentsystems. Due to continuous technical improvementof the infotainment system and possible updates tothe unit's software, the displays and functions onthe infotainment system may differ from the detailsgiven in this manual. No claims may be derivedfrom the differing details, illustrations or descrip-tions.Please ensure that this manual is in the vehicle ifyou lend or sell the vehicle to someone else. Composition Touch, Composition Colour2
 CONFIDENTIAL not for distribution IntroductionBefore using the unit for the first timeBefore using the infotainment system for the first time, carry out the following steps. This willenable you to use the infotainment system safely and make full use of the functions it provides:Observe safety notes  ⇒ page 3.Familiarise yourself with the controls for the infotainment system ⇒ page 7.In the System setup, reset the infotainment system to its original condition (factory settings)⇒ page 40.Use suitable data storage devices for media mode ⇒ page 20. Safety information for the infotainment systemWARNINGAccidents and injuries can occur if the driveris distracted. Operating the infotainment sys-tem can distract you from the road.● Always drive carefully and responsibly.● Select volume settings that allow signalsfrom outside the vehicle (such as emergencyservices sirens) to be easily heard at alltimes.● Setting the volume too high may damageyour hearing. This also applies even if youare only exposed to high volumes for shortperiods.WARNINGThe volume level may suddenly change whenyou switch audio source or connect a newaudio source.● Reduce the base volume before switchingaudio source or connecting a new audiosource.WARNINGConnecting, inserting or removing a storagedevice while the vehicle is in motion can dis-tract you from the road and lead to accidents.WARNINGConnecting leads for external devices mayobstruct the driver.● Arrange the connecting leads so that theydo not obstruct the driver.WARNINGExternal devices that are placed loose in thevehicle or not properly secured can be flungthough the interior and cause injuries duringa sudden driving or braking manoeuvre, or inthe event of an accident.● You should never position or attach an ex-ternal device on a door, on the windscreen orabove or near to the areas marked “AIRBAG”on the steering wheel, the dash panel and theseat backrests, or between these areas andthe vehicle occupants. External devices cancause serious injury in an accident, especial-ly when the airbags deploy.WARNINGThe armrest may obstruct the driver's armmovements, which could cause accidentsand severe injuries.● Always keep the armrest down while thevehicle is in motion.WARNINGOpening the housing on a CD player can leadto injuries from invisible laser radiation.● CD players should only be repaired by aqualified workshop.NOTICEThe infotainment system can be damaged byincorrect insertion of a storage device or inser-tion of an incompatible storage device. Introduction 3142.5R6.RCT.20
 CONFIDENTIAL not for distribution NOTICE (Continued)● When inserting a memory card, ensure thatit is correctly positioned ⇒ page 20.● Applying force may destroy the memorycard slot's locking mechanism.● Only use suitable memory cards.● When inserting and removing a CD, alwayshold it flat and at a right angle to the front ofthe unit. Inserting or removing a CD at an angleto the drive can lead to scratching ⇒ page 20.● Inserting a second CD while a CD is alreadyin the CD drive or being ejected can destroy theCD drive in the unit. Always wait until the CD iscompletely ejected!NOTICEThe CD drive can be damaged by any foreignobjects attached to a storage device, and by ir-regularly shaped storage devices.NOTICE (Continued)● Only clean 12 cm standard CDs should beused.– Do not affix stickers or other items to thedata storage device. Stickers may peel offand damage the CD drive.– Do not use printable data storage devi-ces. Coatings and prints may peel off anddamage the drive.– Do not insert 8 cm single CDs or irregu-larly shaped CDs or DVDs.– Do not insert DVD Plus discs, dual discsor flip discs, as these are thicker than nor-mal CDs.NOTICEThe vehicle loudspeakers may be damaged ifthe volume is too high or the sound is distor-ted. Composition Touch, Composition Colour4
 CONFIDENTIAL not for distribution Introduction 5142.5R6.RCT.20
 CONFIDENTIAL not for distribution Overview of the control elementsFig. 1  Overview of the control elementsDifferent versions of the infotainment system are supplied. The labelling and functions of the infotainmentbuttons ⇒ Fig. 1  2 and the position of the CD slot  5 may vary between versions. Rotary/push knob:–Press to switch on or off ⇒ page 7.–Turn to adjust the basic volume on whichever source is in use ⇒ page 7.Infotainment buttons: press a button to select a function.–RADIO : switches to radio mode and changes frequency band in radio mode ⇒ page 12.–MEDIA : switches to media mode ⇒ page 20.–CAR : opens vehicle and system settings ⇒ Booklet Owner's manual, chapter Introduction to the in-fotainment system.–SETUP : opens menu and system settings ⇒ page 40.–SOUND : opens sound and volume settings ⇒ page 40.–EJECT : ejects the CD ⇒ page 20.–MUTE : mute the audio source ⇒ page 8.–PHONE : opens the telephone control system ⇒ page 30. The current audio source is muted if nomobile telephone provision is installed.Touchscreen ⇒ page 7.Setting knob: the function of this button depends on the unit's operating state.– In all radio modes: turn for manual station or channel selection. Press to start and stop the scanfunction ⇒ page 12.– In media mode: turn to open the track list. Press to start and stop the scan function ⇒ page 20.–Turn to select menu options in long lists and press to access the selected option (e.g. select a sta-tion from the station list).CD slot: for inserting and removing CDs ⇒ page 20.AUX-IN socket: for connecting an external audio source ⇒ page 20.Memory card slot: the slot is located underneath or to the left of the screen, depending on the unitversion ⇒ page 20. 1234567Composition Touch, Composition Colour6
 CONFIDENTIAL not for distribution General information on operating the unitIntroductionThis chapter contains information on the followingsubjects:Rotary/push knobs and infotainment buttons  . 7Switching on and off  . . . . . . . . . . . . . . . . . . . . . 7Adjusting base volume  . . . . . . . . . . . . . . . . . . . 8Operating function buttons and displays onthe screen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Selecting list entries and browsing lists  . . . . . 9Input windows with on-screen keypad  . . . . . . 10Additional display information and displayoptions  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Changes to settings may cause the display contentto vary and some aspects of the infotainment sys-tem operation to differ from the descriptions givenin this manual.Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6Lightly pressing the buttons or briefly touch-ing the touchscreen is sufficient to operatethe infotainment system.Not all listed function buttons and functionsmay be available due to the device softwareused in your market. The equipment is not faulty ifa function button is missing from the screen.Due to country-specific legislation, certainfunctions cannot be selected on the screenwhen the vehicle is travelling above a certainspeed.Using a mobile telephone in the vehicle maycause noise from the vehicle loudspeakers.There may be restrictions on the use of Blue-tooth® devices in some countries. Informationis available from the local authorities.In some vehicles equipped with ParkPilot, thevolume of the current audio source is auto-matically lowered when reverse gear is engaged.Volume reduction can be set in the Sound setupmenu⇒ page 42. Rotary/push knobs and infotainment buttonsFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 7.Rotary/push knobsThe left-hand rotary/push knob  ⇒ Fig. 1  1 is re-ferred to as the volume control or the on/off switch.The right-hand rotary/push knob ⇒ Fig. 1  4 is re-ferred to as the setting knob.Infotainment buttonsThis manual uses a button symbol with blue con-tent and the term “infotainment button” to refer tobuttons on the infotainment system, e.g. the info-tainment button  MEDIA .Infotainment buttons are operated either by press-ing them or by pressing and holding.Switching on and offFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 7.To switch the infotainment system on or off man-ually, briefly press the rotary/push knob ⇒ Fig. 1  1.After switching on, the system starts at the last se-lected volume setting, provided that this does notexceed the preselected maximum switch-on vol-ume ⇒ page 42, Sound and volume settings.Depending on the unit version and the country, theinfotainment system may switch off automaticallywhen the engine is switched off or the vehicle key Introduction 7142.5R6.RCT.20
 CONFIDENTIAL not for distribution is removed from the ignition lock. If the infotain-ment system is switched on again, it will switch offautomatically after approximately 30 minutes(switch-off delay).The infotainment system is permanentlylinked to the vehicle. It cannot be used in an-other vehicle.If the vehicle battery has been disconnected,the ignition must be switched on beforeswitching the infotainment system back on. Adjusting base volumeFirst read and observe the safety warnings   on page 3 and the introductory informationon page 7.Function: actionIncreasing the volume: turn the volume control  ⇒ Fig. 1  1 clockwise or press the   button on themultifunction steering wheel ⇒ Booklet Owner's manual.Decreasing volume: turn the volume control  ⇒ Fig. 1  1 anticlockwise or press the   button on themultifunction steering wheel.Changes to the base volume are indicated by a“bar” on the screen. During this time the infotain-ment system cannot be operated.It is possible to preset certain volume settings andadjustments ⇒ page 42.Muting the infotainment system● Turn the volume control  ⇒ Fig. 1  1 anti-clockwise until  is displayed.●OR: press the  MUTE  infotainment system but-ton1) ⇒ Fig. 1  2.Any media source currently being played is stop-ped while the infotainment system is muted.  ap-pears on the display.If the base volume has been considerably in-creased to play a certain audio source, re-duce the volume again before switching to anotheraudio source. Operating function buttons and displays on the screenFig. 2  Overview of possible function buttons onthe screenFirst read and observe the safety warn-ings 1) Depending on the unit version.Composition Touch, Composition Colour8
 CONFIDENTIAL not for distribution Inactive (grey) function buttons cannot be selected.Overview of displays and function buttonsDisplays and function buttons: action and effectAIn the title bar, the currently selected menu and any other possible function buttons aredisplayed.BTouch to open a further menu.CMove the crosshair across the screen with slight pressure without losing contact.OR: touch the desired position on the screen, the crosshair moves to this position.Touch to move up one level at a time from certain lists.Touch to move up one level at a time to the main menu from a submenu or to undo in-puts made.... Touch to open a pop-up window (option window), displaying further setting options. ...  /   ... Some functions or displays are marked with a checkbox and are activated  or deacti-vated  by touching this box.OK Touch to confirm an input or selection.Touch to close a pop-up window or an input window.+ /  -Touch to change settings incrementally.Move the slider across the screen with slight pressure without losing contact. Selecting list entries and browsing listsFig. 3  List entries settings menuFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 7.List entries can be opened by touching them di-rectly on the screen or by using the setting knob⇒ Fig. 1  4.Marking and selecting list entries with thesetting knob●Turn the setting knob to mark each consecutivelist entry with a selection box so you can browsethrough the list.●Press the setting knob to select the marked listentry.Browsing lists (scrolling)If there are more items available in a list view thancan be displayed on the screen, function buttonsfor scrolling or a scroll bar are displayed on theright of the screen ⇒ Fig. 3.●Browsing lists line-by-line: touch the   or  function button briefly.●Browsing lists page-by-page: briefly touch thescreen above or below the scroll marker.●Browsing long lists quickly page-by-page: touchand hold the screen above or below the scrollmarker.●To quickly scan through a long list, place yourfinger on the scroll marker and move it over thescreen without losing contact. Lift your finger offthe screen when you reach the desired position. Introduction 9142.5R6.RCT.20
 CONFIDENTIAL not for distribution Input windows with on-screen keypadFig. 4  Input window with on-screen keyboardFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 7.Input windows with on-screen keyboard allow youto enter text, such as an entry name for storing adestination or a search term for searching in longlists.Not all of the function buttons listed here are avail-able in all countries and for all topics.Subsequent chapters only explain those functionsthat differ from the general view described here.The input line with the cursor is located on the leftin the top line of the screen *. All inputs are dis-played here.Input windows for free text inputAn input window for free text entry allows any let-ter, number and special character to be entered inany combination.Touching the  OK  function button applies the se-quence of characters currently displayed in thewindow.Input windows for selecting a stored entryIt is only possible to select a sequence of letters,numbers and special characters that matches astored entry.Every time a character is entered, a destinationcorresponding to the specifications is proposed inthe input line. When terms are made up of morethan one word, the space must be entered as well.If fewer than 99 entries are available, the numberof remaining entries is displayed after the input line⇒ Fig. 4  2. Touching this function button displaysa list of these remaining entries.Overview of function buttonsFunction buttons: action and effect1123... : touch to open the input window for numbers and special characters.ABC... : touch to go back to the input window for letters.2Displays the number and opens the list of entries corresponding to the specificationsthat are still available.Letters/numbers Touch to insert the character in the input line.Letters and Press and hold to open a pop-up window with special characters based on the lettershown.Touch the desired character to enter it. Some special characters can also be written out(e.g. “AE” for “Ä”).Touch to switch between upper and lower case.       Touch to enter a space.OK Touch to accept the suggestion in the input line and close the input window.Touch to delete characters in the input line from right to left.Press and hold to delete several characters at once.Touch to close the input window. Composition Touch, Composition Colour10
 CONFIDENTIAL not for distribution Additional display information and display optionsFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 7.The displays that appear on the screen can varydepending on the settings, and may differ fromthose described here.Displays such as the current time and the currentoutside temperature can be displayed on thescreen in the status bar.All displays appear only after the infotainment sys-tem has completed start-up. Introduction 11142.5R6.RCT.20
 CONFIDENTIAL not for distribution Audio modeRadio modeIntroductionThis chapter contains information on the followingsubjects:RADIO main menu  . . . . . . . . . . . . . . . . . . . . . . 12RDS radio data service . . . . . . . . . . . . . . . . . . . 13Station buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 14Selecting, setting and storing stations . . . . . . . 14Scan function (SCAN) . . . . . . . . . . . . . . . . . . . . 16Radio text  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16TP function (traffic program) . . . . . . . . . . . . . . . 17Incoming traffic announcement  . . . . . . . . . . . . 17FM/AM settings  . . . . . . . . . . . . . . . . . . . . . . . . . 18Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6● Basic information on use ⇒ page 7● Menu and system settings (SETUP)⇒ page 40Multi-storey car parks, tunnels, high buildingsand mountains can impair radio reception.Foil or metal-coated stickers attached to thewindows may affect reception on vehicleswith a window aerial. RADIO main menuFig. 5  RADIO main menu Fig. 6  Radio mode station listFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.Selecting the frequency band● Select the required frequency band by pressingthe  RADIO  infotainment button.Function buttons in the RADIO main menuFunction button: effect1Changes the displayed station button group by touching the function button.Opens the list of currently receivable radio stations ⇒ page 14.Opens the frequency dial for the selected frequency band ⇒ page 15.Opens the settings menu for the currently activated frequency band (FM or AM)⇒ page 18. Composition Touch, Composition Colour12
 CONFIDENTIAL not for distribution Function button: effect< /  >Browses through the available or stored stations. Setting for the arrow buttons in theFM/AM setup menu ⇒ page 18.SCAN The function button is only displayed while the scan function is on ⇒ page 16.1...  to  12... Station buttons for storing stations ⇒ page 14.Updates the station list (AM frequency band) ⇒ page 15.Possible displays and symbolsDisplay: meaningADisplays station frequency or station name, and also possibly radio text. Station nameand radio text are only displayed when RDS is available and activated ⇒ page 13.RDS offa) The RDS radio data service is deactivated. RDS can be activated in the FM setupmenu ⇒ page 18.TP TP traffic news is activated and can be received ⇒ page 17.No TP No traffic news station can be received.The radio station is stored to a station button.a) Varies by country and unit version. RDS radio data serviceFig. 7  RADIO main menu Fig. 8  Radio mode station listFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.RDS (radio data system) is a radio data servicewhich enables additional FM services, such as thedisplay of station names, automatic station track-ing, radio text and TP traffic news (TP).RDS is not supported by all units and is not availa-ble everywhere or on every FM radio station.RDS can be deactivated in some country and unitversions ⇒ page 18.Without RDS it is not possible to use radio dataservices.Station name and automatic station trackingIf RDS is available, station names can be dis-played in the RADIO main menu and in the FMstation list.FM radio stations may occasionally or continuouslybroadcast different content on different regionalfrequencies under the same station name (e.g. Ra-dio 2).By default, automatic station tracking alwaysswitches to the currently selected station's frequen-cy that offers the best reception, as the vehicletravels from one area to the next. As a result, youmay lose the regional programme you are listeningto.Automatic frequency changing and automatic sta-tion tracking can be deactivated in the FM setup⇒ page 18. Audio mode 13142.5R6.RCT.20
 CONFIDENTIAL not for distribution The radio stations are responsible for thecontent of the information sent. Station buttonsFig. 9  RADIO main menuFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.In the RADIO main menu, you can store stationsfrom the currently selected frequency band on12 consecutively numbered function buttons.These function buttons are called station buttons.Selecting stations via the stationbuttonsTouch the station button that shows the required station.When a stored station is selected via the station buttons, it will only beplayed if it can be received at your current location.Changing station button groupTouch the ⇒ Fig. 9  1 function button.The station buttons are displayed in groups of four function buttons(1 ...  to  4 ... ,  5 ...  to  8 ...  and  9 ...  to  12 ... ).Displaying station buttons If radio text is shown instead of the station buttons, touch radio text inorder to show the station buttons.Storing stations to station but-tonsSee Storing stations ⇒ page 15.Selecting, setting and storing stationsFig. 10  RADIO main menu Fig. 11  Radio mode station list Composition Touch, Composition Colour14
 CONFIDENTIAL not for distribution First read and observe the safety warnings   on page 3 and the introductory informationon page 12.Selecting stationsSelecting stations using arrowbuttons< /  >Touch the  < or  > ⇒ Fig. 10 function button.The unit only switches to stored or receivable stations, depending onwhat settings have been made for the arrow buttons. Setting for the ar-row buttons in the FM/AM setup menu ⇒ page 18.Selecting stations from a stationlistTouch the   ⇒ Fig. 10 function button to open the station list.Search through the list and touch the required station to select it.To close the station list, touch the   ⇒ Fig. 11 function button.Updating the station listIn the FM frequency band the station list is updated automatically.In the AM frequency band, touch the   ⇒ Fig. 11 function button to up-date the station list.Tuning to a station frequency manuallyDisplaying the frequency dial Turn the setting knob one stop further.OR: touch the   ⇒ Fig. 10 function button.Adjusting the frequency instagesTurn the setting knob.OR: touch the arrow buttons to the left or the right of the frequencyband.Quickly browsing through thefrequency bandTouch one of the arrow buttons at the top of the screen ⇒ Fig. 10. Thenext receivable station is set automatically.OR: press and hold one of the arrow buttons at the top of the screen⇒ Fig. 10. When you release the button, the unit automatically tunes tothe next available station.OR: place your finger on the slider in the frequency dial and drag italong the dial.Hiding the frequency bandBriefly press the setting knob.Manual frequency selection is also closed if you select a station with astation button. The frequency band closes automatically after a periodof inactivity.Storing stationsStoring the current station to astation buttonPress and hold the desired station button ⇒ Fig. 10 until a tone is soun-ded.The station currently playing is then stored on that station button.Storing a station from the stationlist to a station buttonTouch the   ⇒ Fig. 10 function button to open the station list.Stations already stored on a station button are marked in the station listwith the  ⇒ Fig. 11 symbol.Select the desired station by pressing and holding on the screen.Touch the button to which you wish this station to be assigned.A signal tone sounds, and the station is then stored on this station but-ton. Repeat the process to store further stations from the station list.Deleting stored stations All stored stations can be deleted individually or together in the FM/AMsetup menu ⇒ page 18. Audio mode 15142.5R6.RCT.20
 CONFIDENTIAL not for distribution Stopping station names scrolling (FMfrequency)Some radio stations transmit a very long stationname, which is shown on the screen as a scrollingtext.To fix the text that is currently displayed to thescreen, touch the station name and hold until atone is sounded.Fixed station names are indicated by a dot to eachside of the name.The fixed text is adopted for all the station buttonson which the corresponding station is stored. Scan function (SCAN)First read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.When the scan function is running, all availablestations on the current frequency band are playedin sequence for approximately 5 seconds each.SCAN  appears on the display.Starting the scan function Press the setting knob briefly.OR: touch the   function button and then select  SCAN .Stopping the scan functionPress the setting knob briefly.OR: touch the  SCAN  function button to end the scan function at the stationarrived at.Manually selecting a station with the station buttons also stops the scanfunction. Radio textFig. 12  RADIO main menu Fig. 13  Radio mode: radio text is visibleFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.Some RDS-compatible stations also broadcast ad-ditional text information known as radio text.The station buttons can be hidden to enlarge thedisplay area for the radio text ⇒ Fig. 13.Hiding station buttons Touch displayed radio text ⇒ Fig. 12.Displaying station buttons Touch displayed radio text ⇒ Fig. 13.Switching off radio text per-manentlyIn the FM setup menu, deactivate the   Radio text  function button by touch-ing it ⇒ page 18. Composition Touch, Composition Colour16
 CONFIDENTIAL not for distribution TP function (traffic program)Fig. 14  RADIO main menu with TP display Fig. 15  Radio mode: station list with TP displayFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.Traffic news monitoring with the TP function is onlypossible if a traffic news station is available. Trafficnews stations are indicated in the RADIO mainmenu and in the station list by TP ⇒ Fig. 14 and⇒ Fig. 15.Some stations that do not broadcast their own traf-fic news support the TP function through a link to atraffic news station (EON).Switching the TP function on and off● In the FM/AM setup menu, activate  or deac-tivate  the  Traffic program (TP)  function button bytouching it ⇒ page 18.If the station that is currently selected does notsupport the TP function, No TP will be shown inthe top right of the screen.Activated TP function and station selectionWhile traffic news monitoring is on, TP is displayedat the top right in audio mode ⇒ Fig. 14. Traffic an-nouncements broadcast by the current station or alinked traffic news station will interrupt the currentaudio mode.In FM mode, the selected station must support theTP function. After the TP function is switched on, ifyou change via the station buttons or manual se-lection to a station that does not support the TPfunction, traffic news monitoring will not be possi-ble (display: No TP).If the currently selected traffic news station can nolonger be received, No TP is also displayed andyou will have to start a manual station search⇒ page 14.In AM mode or media mode, the unit will alwaysautomatically tune to a traffic news station in thebackground, provided that a TP station is availa-ble. This procedure may take some time. Incoming traffic announcementFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.Incoming traffic announcements will interrupt theactive audio mode.During the traffic announcement a pop-up windowis displayed and, if required, the radio is switchedto the traffic news station (EON) for the duration ofthe traffic announcement.The media mode is paused and the volume is ad-justed to the preset level ⇒ page 42.Audio mode 17142.5R6.RCT.20
 CONFIDENTIAL not for distribution The traffic announcement volume setting can beadjusted with the volume control  ⇒ Fig. 1  1.The adjusted volume setting will be applied to sub-sequent announcements.● Touch the  Cancel  function button to end thetraffic announcement. The TP function remains ac-tivated.●OR: touch the  Deactivate  function button to endthe current traffic announcement and permanentlyswitch off the TP function. FM/AM settingsFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 12.FM setup● Select the FM frequency band by pressing theRADIO  infotainment button.● Touch the   function button to open the FMsetup menu.Function button: effectScan : scan function (SCAN). When the scan function is running, all available stations on the current fre-quency band are played in sequence for approximately 5 seconds each ⇒ page 16.Arrow buttons : define the settings for the  < und  > arrow buttons. The setting is adopted for all frequencybands (FM, AM). Preset list : all stored stations on the selected frequency band can be browsed with the arrowbuttons. Stations : all available stations on the selected frequency band can be browsed with the arrowbuttons. Traffic program (TP) : the TP function (traffic news monitoring) is activated ⇒ page 17. Radio text : radio text is activated ⇒ page 16.Delete preset list : to delete some or all stored stations. All : all stored stations will be deleted (FM 1, FM 2, FM 3).  To delete individual stations, selected the desired preset list  FM 1 ,  FM 2  or  FM 3 . Then touchthe station button of the station you wish to delete.Advanced setup : settings for the RDS radio data services. RDS Regional : defines the setting for automatic station tracking with RDS ⇒ page 13.  Fixed : the unit only switches to alternative frequencies for the selected station thatbroadcast the same regional service.    Automatic : the unit always switches to the station's frequency that currently offers thebest reception. As a result, regional programmes may be interrupted.  Radio Data System (RDS) a): the radio data system (RDS) is deactivated ⇒ page 13. If the checkbox is deactivated, the traffic program (TP) and radio text functions are not available.  Alternative frequency (AF) : automatic station tracking is activated. If the  checkbox is deactiva-ted, automatic station tracking is switched off. The  RDS Regional  function button is then inac-tive (greyed out).a) Varies by country and unit version.AM setup● Select the AM frequency band by pressing theRADIO  infotainment button.● Touch the   function button to open the AMsetup menu. Composition Touch, Composition Colour18
 CONFIDENTIAL not for distribution Function button: effectScan : scan function (SCAN). When the scan function is running, all available stations on the current fre-quency band are played in sequence for approximately 5 seconds each ⇒ page 16.Arrow buttons : define the settings for the  < und  > arrow buttons. The setting is adopted for all frequencybands (FM, AM). Preset list : all stored stations on the selected frequency band can be browsed with the arrowbuttons. Stations : all available stations on the selected frequency band can be browsed with the arrowbuttons. Traffic program (TP) : the TP function (traffic news monitoring) is activated ⇒ page 12.Delete preset list : to delete some or all stored stations. All : all stored stations will be deleted (AM 1, AM 2, AM 3).  To delete individual stations, select the desired preset list  AM 1 ,  AM 2  or  AM 3 . Then touch thestation button of the station you wish to delete. Audio mode 19142.5R6.RCT.20
 CONFIDENTIAL not for distribution Media modeIntroductionThis chapter contains information on the followingsubjects:Data storage device and file requirements  . . . 20Playing order of files and folders  . . . . . . . . . . . 21MEDIA main menu  . . . . . . . . . . . . . . . . . . . . . . 22Changing the media source  . . . . . . . . . . . . . . . 23Changing tracks in the MEDIA main menu . . . 24Selecting tracks from the track list . . . . . . . . . . 24Inserting or ejecting a CD . . . . . . . . . . . . . . . . . 25Inserting or removing a memory card  . . . . . . . 26External data storage device connected toUSB port  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26External audio source connected to the AUX-IN socket  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Connecting an external audio source viaBluetooth® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Media settings  . . . . . . . . . . . . . . . . . . . . . . . . . . 28“Media sources” are audio sources containing au-dio files on various different storage devices (e.g.CD, memory card, external MP3 player). These au-dio files can be played by the infotainment systemfrom its corresponding drives or audio input sock-ets (internal CD drive, memory card slot, AUX-INsocket etc.).CopyrightAudio and video files stored on data storage devi-ces are normally subject to national and interna-tional copyright laws. Observe legal requirements.Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6● Basic information on use ⇒ page 7This product is subject to certain intellectualproperty rights and copyrights owned by theMicrosoft Corporation. The use or distribution ofthis type of technology outside this product re-quires a licence from Microsoft or an authorisedMicrosoft company. Data storage device and file requirementsFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.Factory-fitted CD drives conform to safety class 1according to DIN IEC 76 (CO) 6/ VDE 0837.The infotainment system only accepts standard 12cm CDs, and memory cards measuring32 mm x 24 mm x 2.1 mm or 1.4 mm.The supported file formats listed are collectively re-ferred to below as “audio files”. A CD containingaudio files of these types is referred to as an “au-dio data CD”.Media source Requirements for playing in the unit Audio CDs (up to 80 minutes). – CD Digital Audio specification . CD-ROM, CD-R and CD-RW audiodata CDs up to max. 700 MB (mega-bytes) with the file systems ISO 9660Level 1 or 2, Joliet or UDF 1.02, 1.5, 2.01 SD and MMC memory cards with thefile systems FAT12, FAT16, FAT32, VFATor exFAT up to max. 2 GB (gigabytes),SDHC memory cards up to max. 32 GBand SDXC memory cards up to max. 2TB (terabytes).– MP3 files (.mp3) with bit rates of between 32 and 320 kbit/sor with variable bit rate.– WMA files (.wma) up to 10 mono/stereo without copy protec-tion.– Playlists in the formats PLS, M3U and WPL.– Playlists no larger than 20 kB and containing no more than1,000 entries.– File name and path information not longer than 256 charac-ters. Composition Touch, Composition Colour20
 CONFIDENTIAL not for distribution Media source Requirements for playing in the unitAUX External audio source. – Playback of external audio sources via 3.5 mm jack plug⇒ page 27. Audio file playback via Bluetooth®a). – The external media player must support the A2DP Blue-tooth® profile ⇒ page 28.a) Bluetooth® is a registered trademark of Bluetooth® SIG, Inc.Restrictions and notesContamination, exposure to high temperatures andmechanical damage can render storage devicesunusable. Please observe the manufacturer's in-structions.Variations in the quality of storage devices from dif-ferent manufacturers can lead to problems duringplayback.Please observe copyright laws.The unit may be unable to read individual tracks orthe entire storage device due to the storage devi-ce's configuration or the devices and programsused for recording. Information about the bestways to create audio files and configure storagedevices (compression rate, ID3 tag etc.) can befound online.The reading time may vary considerably depend-ing on the condition of the storage device (copyingand deleting actions), folder structure and file type.Playlists only determine a certain playing order.There are no files stored in a playlist. The unit willnot play a playlist if the files are not stored on thestorage device at the locations referred to by theplaylist (relative file paths).Do not use memory card adapters.No liability can be accepted for damaged orlost files on the storage devices. Playing order of files and foldersFig. 16  Possible structure on an audio data CDFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.Audio files  on storage devices are often sortedby folders  and playlists  to determine a certainplaying order.Tracks, folders and playlists on a storage deviceare each sorted by name in alphanumeric order.The illustration shows a typical audio data CD thatcontains tracks , folders  and subfolders⇒ Fig. 16.The tracks are played in the following order1):Tracks  1 and  2 in the CD's root directoryTracks  3 and  4 in the first folder F1 in theCD's root directoryTrack  5 in the first subfolder F1.1 of thefolder F1Track  6 in the first subfolder F1.1.1 of thesubfolder F1.1Track  7 in the second subfolder F1.2 ofthe folder F1Tracks  8 and  9 in the second folder F2The playing order can be altered by selectingdifferent playback modes ⇒ page 22. 1.2.3.4.5.6.1) The   Mix/Repeat including subfolders  function must be activated ⇒ page 40 in the Media setup menu.Audio mode 21142.5R6.RCT.20
 CONFIDENTIAL not for distribution Playlists are not played automatically. In-stead they must be specifically selected viathe track selection menu ⇒ page 24. MEDIA main menuFig. 17  MEDIA main menuFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.In the MEDIA main menu, various media sourcescan be selected and played.● Press the  MEDIA  infotainment button to openthe MEDIA main menu ⇒ Fig. 17.Playback of the media source that was most re-cently played resumes from the point where it stop-ped.The media source currently playing is indicated atthe bottom left in the function button  1.The MEDIA main menu will indicate if no mediasource is available.Function buttons in the MEDIA main menuFunction button: effect1Indicates the media source currently selected. Touch to select a different media source⇒ page 23. CD : internal CD drive ⇒ page 25. SD card : memory card ⇒ page 26. USB : external data storage device connected to USB port ⇒ page 26. AUX : external audio source connected to AUX-IN socket ⇒ page 27. BT audio : Bluetooth® audio ⇒ page 28.Opens the track list ⇒ page 24.< /  >Changes track when in media mode ⇒ page 24Playback stops. The   function button changes to   ⇒ page 24.Playback is resumed. The   function button changes to   ⇒ page 24.Opens the Media setup menu ⇒ page 28.Repeats all tracks.All tracks on the same memory level as the current track will be repeated. If Mix/repeat including subfolders  is activated in Media setup subfolders are also inclu-ded⇒ page 28.Repeat current track.Random play.All tracks on the same memory level as the current track are included. If Mix/repeat including subfolders  is activated in Media setup subfolders are also inclu-ded⇒ page 28. Composition Touch, Composition Colour22
 CONFIDENTIAL not for distribution Function button: effectSCANWhen the scan function is running, all tracks in the current track list are played for approx-imately 10 seconds each.The function button is only displayed while the scan function is on. To start the scan func-tion, press setting knob ⇒ Fig. 1  4 or open the   track list and touch the  SCAN  functionbutton.Displays and symbols in the MEDIA main menuDisplay: meaningADisplay of track information (CD text , ID3 tag with MP3 files).Audio CDs: track and track number corresponding to the track order on the CD are dis-played.Audio files: artist name, album name and track name are displayed.BTrack playing time and remaining playing time in minutes and seconds. The remainingplaying time displayed may differ for audio files with variable bit rate (VBR).RDS offa) The RDS radio data service is deactivated. RDS can be activated in the FM setup menu⇒ page 12.TP TP is activated and can be received ⇒ page 12.No TP No traffic news station can be received.a) Varies by market and unit version. Changing the media sourceFig. 18  MEDIA main menuFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.● In the MEDIA main menu, press the  MEDIA  in-fotainment button as often as required to switchbetween the available media sources.●OR: in the MEDIA main menu, touch the⇒ Fig. 18  1 function button and select the desiredmedia source.Media sources not currently available are shownas inactive (grey) in the pop-up window.If a media source that has already been played isselected again, playback is resumed from the pointthat was last reached.Optionally selectable media sourcesFunction button: media sourceCD Audio or audio data CD in the internal CD drive ⇒ page 25.SD card Memory card ⇒ page 26.USB External data storage device connected to USB ⇒ page 26.AUX External audio source connected to AUX-IN socket ⇒ page 27.BT audio Bluetooth® audio ⇒ page 28.The media source can also be changed inthe Track list view ⇒ page 24. Audio mode 23142.5R6.RCT.20
 CONFIDENTIAL not for distribution Changing tracks in the MEDIA main menuFig. 19  MEDIA main menuFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.You can browse through the tracks of the mediasource that is currently playing using the arrow but-tons.You cannot switch to playback from a playlist us-ing the arrow keys. Playback from a playlist mustbe started manually via the track selection menu⇒ page 24, Selecting tracks from the track list.Controlling playback via the MEDIA main menuAction EffectBriefly touch the function button  < once. Goes to the start of the current track. If the track is short-er than 3 seconds, the system goes to the start of theprevious track.Briefly touch the function button  < twice. Goes to the start of the previous track. Changes from thefirst track to the last track on the storage device that isbeing played.Briefly touch the function button  > once. Goes to the next track. Changes from the last track tothe first track on the storage device that is being played.Press and hold the  < function button. Fast reverse.Press and hold the  > function button. Fast forward.Briefly touch the   function button once. Playback stops. The   function button changes to  .Briefly touch the   function button once. Playback is resumed. The   function button changes to.Selecting tracks from the track listFig. 20  Track list from a media sourceFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.Opening the track list● In the MEDIA main menu, touch the   functionbutton ⇒ Fig. 19 to open the track list. The trackthat is currently playing is highlighted ⇒ Fig. 20.●Search through the track list and touch the de-sired track.If track information is available, the track name isdisplayed instead of Track + No..Composition Touch, Composition Colour24
 CONFIDENTIAL not for distribution Overview of function buttons in the track listFunction button: effectOpens the Sources menu. Touch to select a different media source.AIndicates the media source currently selected. Touch to change the media source. CD : internal CD drive ⇒ page 25. SD card : memory card ⇒ page 26. USB : external data storage device connected to USB port ⇒ page 26. AUX : external audio source connected to AUX-IN socket ⇒ page 27. BT audio : external media player connected via Bluetooth® ⇒ page 28.Touch the function button to open the parent folder of the current folder on the mediasource. The name of the current folder will be displayed to the right of the symbol.Starts playback at the first track.Repeats all tracks.All tracks on the same memory level as the current track will be repeated. If Mix/repeat including subfolders  is activated in Media setup subfolders are also inclu-ded⇒ page 28.Repeat current track.Random play.All tracks on the same memory level as the current track are included. If Mix/repeat including subfolders  is activated in Media setup subfolders are also inclu-ded⇒ page 28.SCAN When the scan function is running, all tracks in the current track list are played for approx-imately 10 seconds each.Closes track list.Tracks, folders and playlists can also bemarked by turning the setting knob then loa-ded or opened up or opened by pressing the knob. Inserting or ejecting a CDFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.The internal CD drive can play audio CDs and au-dio data CDs.When an audio CD without CD text is playing, onlyTITLE and the track number, corresponding to theplaying order on the data medium, are displayed inthe centre line of the screen.If the audio file CDs played contain additional trackinformation (CD text , ID3 tag for MP3 files), itcan be displayed on the screen.Inserting a CD● Hold the CD with the printed side facing up.● Push the CD into the CD slot only to the pointwhere it is drawn in automatically.● When the CD is inserted, playback will start au-tomatically.Ejecting a CDIn some countries, the vehicle key must be in theignition lock of a cabriolet vehicle in order to eject aCD (anti-theft protection).● Press the  EJECT  infotainment button.● The CD in the drive will be ejected and must beremoved within approximately 10 seconds.For safety reasons, the CD will be drawn back intothe player if it is not removed within roughly 10seconds, but the unit will not switch to CD mode.CD cannot be read or is faultyA message will be shown on the screen if the dataon an inserted CD cannot be read or the CD isfaulty.Uneven road surfaces and strong vibrationscan cause playback to jump. Audio mode 25142.5R6.RCT.20
 CONFIDENTIAL not for distribution When the temperature inside the infotain-ment system is too high, loading and play-back of CDs is disabled.If you insert a number of different CDs andreceive the message Error: CD drive ev-ery time, contact a qualified workshop. Inserting or removing a memory cardFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.Only supported audio files are displayed andplayed. Other files are ignored.Inserting a memory cardFig. 1  7Vertical card slotInsert a compatible memory card into the memory card slot with the cut-offcorner first and the lettering facing left (contact surfaces facing down) untilthe card clicks into place.Horizontal card slotInsert a compatible memory card into the memory card slot with the cut-offcorner first and the label facing up (contact surfaces facing down) until thecard clicks into place.If a memory card cannot be inserted, ensure that itis positioned correctly and is compatible with theunit.Playback starts automatically if supported audiofiles are stored on the memory card.Removing a memory cardThe inserted memory card must be prepared forremoval.● In the MEDIA main menu touch the   functionbutton to open the Media setup menu.●OR: press the  SETUP  infotainment button.● Touch the  Remove the SD card safely  function but-ton.●OR: touch the  Remove safely  function button andthen select   SD card .Once the memory card has been ejected from thesystem, a message is shown on the screen andthe function button is greyed out. The memory cardcan then be removed.● Press the inserted memory card. The memorycard springs out of the slot.● Remove the memory card.Memory card cannot be readIf you insert a memory card containing data thatcannot be read, the unit will not change to memorycard mode after loading.A corresponding message is displayed. External data storage device connected to USB port First read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.In some countries and with some equipment lev-els, the vehicle may be fitted with a USB connec-tion  in the stowage compartment in the centreconsole. ⇒ Booklet Owner's Manual, chapter Prac-tical equipment.Only supported audio files are displayed andplayed. Other files are ignored.Playback starts automatically if supported audiofiles are stored on the data storage device.RemovingThe connected storage device must be preparedbefore removal.● In the MEDIA main menu, touch the   functionbutton to open the Media setup menu.●OR: press the  SETUP  infotainment button.● Touch the  Remove safely  function button andthen select   USB .Data media cannot be readThe message No playable files availableappears if the data on the connected storage de-vice cannot be read. Composition Touch, Composition Colour26
 CONFIDENTIAL not for distribution Please read and observe the manufacturer'smanual for the external storage device. External audio source connected to the AUX-IN socketFig. 21  MEDIA main menu Fig. 22  External audio source connected to AUX-INFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.The AUX-IN socket ⇒ Fig. 1  6 can only be usedwith a 3.5 mm jack plug.The connected external audio source is playedover the vehicle speakers and cannot be control-led via the infotainment system.AUX shows on the screen when an external audiosource is connected ⇒ Fig. 22.Connecting an external audio source to theAUX-IN socket● Reduce the base volume on the infotainmentsystem.●Connect the external audio source to the AUX-IN socket.● Start playback on the external audio source.● In the MEDIA main menu, touch the⇒ Fig. 21  1 function button and select  AUX .The output volume of the external audio sourceshould be adjusted to the volume of the other au-dio sources ⇒ page 42.Information on operating an external audio source connected to the AUX-IN socketAction EffectSelecting another audio source on the infotainmentsystem.The external audio source continues to run in thebackground.Stopping playback on the external audio source. The infotainment system remains in the AUX menu.Disconnecting the plug from the AUX-IN socket. The infotainment system switches to playback ofthe most recently played audio source.Please read and observe the manufacturer'smanual for the external audio source.Interference may occur if the external audiosource is powered from the vehicle’s 12-voltsocket. Audio mode 27142.5R6.RCT.20
 CONFIDENTIAL not for distribution Connecting an external audio source via Bluetooth®Fig. 23  MEDIA main menuFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.In Bluetooth® audio mode, audio files from a Blue-tooth® audio source (e.g. mobile telephone) that isconnected via Bluetooth® can be played over thevehicle loudspeakers (Bluetooth® audio playback).Conditions●The Bluetooth® audio source must supportthe A2DP Bluetooth® profile.● The   Bluetooth audio (A2DP/AVRCP)  function mustbe activated in the Bluetooth setup menu⇒ page 39.Starting Bluetooth® audio transfer● Switch on Bluetooth® visibility on the externalBluetooth® audio source (e.g. mobile telephone).● Reduce the base volume on the infotainmentsystem.● Press the  MEDIA  infotainment button.● Touch the ⇒ Fig. 23  1 function button and se-lect   BT audio .● Touch the  Find devices  function button to con-nect an external Bluetooth® audio source for thefirst time.●OR: touch the  Paired devices  function button toselect an external Bluetooth® audio source fromthe list.● Continue the process by following the promptson the infotainment system screen and in the dis-play on the Bluetooth® audio source.You may then have to start playback on the Blue-tooth® audio source manually.When playback on the Bluetooth® audio source isstopped, the infotainment system remains in Blue-tooth® audio mode.Controlling playbackThe extent to which the Bluetooth® audio sourcecan be controlled via the infotainment system var-ies depending on what Bluetooth® audio source isconnected.With media players that support the AVRCP Blue-tooth® profile, playback on the Bluetooth® audiosource can be automatically started or stoppedwhen the unit is switched to Bluetooth® audiomode or to a different audio source. In addition,track display or track change is possible via the in-fotainment system.Due to the large number of possible Blue-tooth® audio sources, it is not possible toguarantee fault-free operation of all describedfunctions.Always switch off the warning and servicetones on a connected Bluetooth® audiosource, e.g. key tones on a mobile telephone, toprevent interference noise and malfunctions. Media settingsFirst read and observe the safety warn-ings   on page 3 and the introductoryinformation on page 20.● Select the MEDIA main menu by pressing theMEDIA  infotainment button.● Touch the   function button to open the Mediasetup menu.Function button: effectRemove the SD card safely : memory card is ejected from the system and can then be safely removed⇒ page 26.Sound : sound settings ⇒ page 42.Bluetooth : opens the Bluetooth setup menu ⇒ page 39. Composition Touch, Composition Colour28
 CONFIDENTIAL not for distribution Function button: effect Traffic program (TP) : the TP function (traffic news monitoring) is activated ⇒ page 12. Mix/Repeat including subfolders : subfolders will be included in the selected playback mode ⇒ page 22.Remove safely : disconnect data storage device (USB storage device or SD card) from the system. Oncethe storage device has been ejected from the system the respective function button is greyed out. Audio mode 29142.5R6.RCT.20
 CONFIDENTIAL not for distribution Telephone control (PHONE)Introduction to telephone control systemIntroductionThis chapter contains information on the followingsubjects:General information . . . . . . . . . . . . . . . . . . . . . . 31Areas where special regulations apply  . . . . . . 31Bluetooth® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Pairing and connecting mobile telephone onthe infotainment system  . . . . . . . . . . . . . . . . . . 32Switching telephone control system off . . . . . . 33The telephone functions described in the followingsection can be controlled via the infotainment sys-tem if a mobile telephone that is switched on ispaired and connected with the infotainment sys-tem.The mobile telephone must support the Blue-tooth® function otherwise a connection cannot bemade between the telephone and the infotainmentsystem.If a mobile telephone is not connected to the info-tainment system, the telephone control systemcannot be used.Observe the notes on using a mobile telephone inthe vehicle without a connection to the externalaerial ⇒ Booklet Owner's manual.Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6● Basic information on use ⇒ page 7WARNINGMaking telephone calls and operating the tel-ephone control system while the vehicle is inmotion can distract you from the road andlead to accidents.● Always drive carefully and responsibly.● Select volume settings that allow signalsfrom outside the vehicle (such as emergencyservices sirens) to be easily heard at alltimes.● Your call may be cut off or you may be un-able to make calls if you are in an area withno mobile telephone network coverage, anWARNING (Continued)area where the network is very weak or, insome cases, in a tunnel, garage or under-pass. This also means that no emergencycalls can be made.WARNINGIf a mobile telephone is not secured or is in-correctly secured in the vehicle, it could beflung though the interior during a suddendriving or braking manoeuvre, or in the eventof an accident. This can cause injuries.● While the vehicle is in motion, always se-cure the mobile telephone properly outsidethe airbag deployment area.WARNINGCarrying a mobile telephone that is switchedon just next to a pacemaker may cause thepacemaker to malfunction.● Maintain a gap of approximately 20 centi-metres between the aerials of the mobile tele-phone and the pacemaker, as mobile tele-phones may affect the functioning of pace-makers.● Do not carry a mobile telephone in yourbreast pocket above your pacemaker whenthe telephone is switched on or in standbymode.●If you suspect interference, switch off themobile telephone immediately.WARNINGThe centre armrest may obstruct the driver'sarm movements if raised, which could causeaccidents and severe injuries.● Always keep the armrest down while thevehicle is in motion.NOTICEHigh speeds, poor weather and poor road con-ditions as well as the network quality may im-pair telephone calls in the vehicle. Composition Touch, Composition Colour30
 CONFIDENTIAL not for distribution General informationFirst read and observe the introductoryinformation and safety warnings   onpage 30.How the individual telephone menus are displayeddepends on the mobile telephone being used.There may be differences.Observe the notes on using a mobile telephone inthe vehicle without a connection to the externalaerial ⇒ Booklet Owner's manual, chapter Vehiclecare and maintenance.Use compatible Bluetooth® devices only. Informa-tion on compatible Bluetooth® products is availablefrom your Volkswagen dealership or online.Follow the operating manual for your mobile tele-phone and the instructions provided by the acces-sory manufacturer.You may experience poor reception or may be cutoff in areas where the signal is weak.Most electronic devices are shielded against high-frequency signals. In rare cases, however, elec-tronic devices may not be shielded against high-frequency signals emitted by the telephone controlsystem. This can cause interference.There may be restrictions on the use of Blue-tooth® devices in some countries. Informationis available from the local authorities.When connecting the telephone control sys-tem with a device using Bluetooth®, read thedevice's operating manual for detailed safety infor-mation. Use compatible Bluetooth® products only. Areas where special regulations applyFirst read and observe the introductoryinformation and safety warnings   onpage 30.Switch off the mobile telephone and mobile tele-phone provision in areas with a risk of explosion.These areas are often clearly marked, but not al-ways ⇒   in Introduction on page 30. They in-clude, for example:●Areas immediately around chemical pipelinesand tanks.● Lower decks of ships and ferries.● The area around vehicles which run on liquidgas (such as propane or butane).● Places where there are chemicals or particlessuch as flour, dust and metal powder in the air.● All other places where the vehicle engine mustbe switched off.WARNINGSwitch off the mobile telephone in areas witha risk of explosion!NOTICEYour mobile telephone must always be switch-ed off in areas where special regulations applyand when the use of mobile telephones is for-bidden. The radiation produced by the mobiletelephone when switched on may interfere withsensitive technical and medical equipment,possibly resulting in malfunction or damage tothe equipment. Bluetooth®First read and observe the introductoryinformation and safety warnings   onpage 30.Bluetooth®Bluetooth® technology is used to connect a mobiletelephone to the telephone control system fitted ina vehicle. A pairing process has to be carried outbefore the telephone control system can be usedwith a Bluetooth® mobile telephone. Telephone control (PHONE) 31142.5R6.RCT.20
 CONFIDENTIAL not for distribution Some Bluetooth® mobile telephones are detectedand connected automatically when the ignition isswitched on, if a connection already exists. For thisto happen, the mobile telephone itself and theBluetooth® function in the telephone must beswitched on and all active Bluetooth® connectionsto other units must be disconnected.The Bluetooth® connection is free of charge.Bluetooth® is a registered trademark of Blue-tooth® SIG, Inc.Bluetooth® profilesWhen a mobile telephone is connected to the tele-phone control system, data is exchanged via oneof the Bluetooth® profiles.Basic telephony Bluetooth® Hands-Free Profile(HFP):● If a mobile telephone is connected via HFP tothe telephone control system, you can make callswirelessly via the hands-free system. The vehicle'sexterior aerial cannot be used with this. Observethe notes on using a mobile telephone in the vehi-cle without a connection to the external aerial⇒ Booklet Owner's manual.Music playback Bluetooth® Advanced Audio Dis-tribution Profile (A2DP):●Bluetooth® profile for the transmission of ster-eo-quality audio signals.Playback controls Bluetooth® Audio Video Re-mote Control Profile (AVRCP):● Bluetooth® profile for displaying track informa-tion and control of playback in the mobile device. Pairing and connecting mobile telephone on the infotainment systemFirst read and observe the introductoryinformation and safety warnings   onpage 30.In order to operate a mobile telephone via the info-tainment system, a single pairing process is re-quired for both devices.Pairing should only be performed when the vehicleis stationary.Conditions●Ignition is switched on.● If necessary, disconnect any headsets from themobile telephone.● The Bluetooth® function must be activated orset to visible on the mobile telephone and on theinfotainment system.● The keypad lock on the mobile telephone hasto be unlocked.Follow the operating manual for the mobile tele-phone.The Bluetooth® function is set to visible on theinfotainment system for about 3 minutes after theignition is switched on.Entries have to be made on the mobile telephonekeypad during the pairing process. The mobile tel-ephone has to be at hand for this.Starting mobile telephone pairing● Press the  PHONE  infotainment button.● Touch the  Find telephone  function button.OR:● Press the  PHONE  infotainment button.● Touch the  Setup function button.● Touch the  Select telephone  function button andthen  Find telephone .Once the search process is complete, the namesof all Bluetooth® devices found will be displayed onthe screen.● Select the mobile telephone to be paired fromthis list of Bluetooth® devices and then selectHands-free telephone (HFP).The infotainment system and the mobile telephoneare now connected. Further input may be requiredon the mobile telephone and on the infotainmentsystem to conclude the connection process. Composition Touch, Composition Colour32
 CONFIDENTIAL not for distribution ● If necessary, confirm the pairing on the mobiletelephone.Depends on the mobile telephone:● Enter the PIN code that is then displayed onthe infotainment system into the mobile telephoneand confirm it.OR:● Compare the PIN code displayed on the info-tainment system with the PIN code displayed onthe mobile telephone. If the PIN code matches, ithas to be confirmed on both devices.The PHONE main menu is displayed and the tele-phone book and the call lists stored in the mobiletelephone are loaded automatically once pairinghas been completed. The time taken by the load-ing process varies depending on the amount of da-ta stored in the mobile telephone. This data isavailable on the infotainment system once theloading process is completed.Pairing and connecting mobile telephonesSeveral mobile telephones can be paired with theinfotainment system, but only one mobile tele-phone can be connected to the infotainment sys-tem at a time.When you switch the infotainment system on, aconnection is automatically set up with the mobiletelephone that was connected last. If no connec-tion can be set up with this mobile telephone, thetelephone control system automatically attempts toset up a connection with the next mobile telephonein the list of paired devices.Bluetooth® connections have a maximum range of10 metres. Any active Bluetooth® connection is in-terrupted when this distance is exceeded. The con-nection is automatically restored as soon as thedevice enters the Bluetooth® range.You will find further information on pairingand connecting mobile telephones on the In-ternet at www.volkswagen.com. Switching telephone control system offFirst read and observe the introductoryinformation and safety warnings   onpage 30.● Switch off the ignition.● Remove the vehicle key from the ignition lock.The telephone control system is switched off andany active call is transferred to the mobile tele-phone.The telephone control system is not switched off ifthe vehicle key is left in the ignition lock after theengine is switched off. Once a set time has ex-pired, a message appears on the infotainment sys-tem screen informing you that the telephone con-trol system will be switched off automatically. Anactive call will be transferred to the mobile tele-phone.The transfer of an active call from the tele-phone control system to the mobile telephonecan take up to approximately 10 seconds (depend-ing on the mobile telephone being used). Telephone control (PHONE) 33142.5R6.RCT.20
 CONFIDENTIAL not for distribution Description of telephone control systemIntroductionThis chapter contains information on the followingsubjects:PHONE main menu . . . . . . . . . . . . . . . . . . . . . . 34During a telephone call  . . . . . . . . . . . . . . . . . . . 35Entering a telephone number . . . . . . . . . . . . . . 36Telephone book menu (Contacts)  . . . . . . . . . . 36Call lists menu  . . . . . . . . . . . . . . . . . . . . . . . . . . 37Speed dial buttons . . . . . . . . . . . . . . . . . . . . . . . 38Telephone settings  . . . . . . . . . . . . . . . . . . . . . . 38Bluetooth settings® . . . . . . . . . . . . . . . . . . . . . . 39User profile settings  . . . . . . . . . . . . . . . . . . . . . 39Some functions and settings are only availablewhen the vehicle is stationary, and are not suppor-ted by all mobile telephones.The range of possible settings depends on thecountry, the unit and the vehicle's equipment speci-fication.Up to 20 devices can be linked to the telephonecontrol system. One device at a time can be con-nected via the hands-free profile (HFP) or audioplayback profile (A2DP) ⇒ page 33.Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6● Basic information on use ⇒ page 7● Introduction to and safety information  for tel-ephone control system ⇒ page 30Using a mobile telephone in the vehicle maycause noise from the vehicle speakers.Some networks might not support all lan-guage-dependent characters and services. PHONE main menuFig. 24  PHONE main menu Fig. 25  Incoming callFirst read and observe the introductoryinformation given on page 34.Assignment to a user profileTelephone book data, call lists and stored speeddial buttons are assigned to a user profile and stor-ed in the telephone control system. They are avail-able when the mobile phone is connected with thetelephone control system again.If, while connected to the radio, telephone bookentries on the mobile telephone are changed, youcan start a manual update of the telephone bookdata via the User profile setup menu⇒ page 39. The telephone book will be automati-cally updated when the telephone is connectedagain (e.g. on the next journey).A maximum of 4 user profiles can be stored formobile telephones in the telephone control system.If another mobile telephone is connected, the userprofile which has not been used for the longestamount of time will be deleted automatically.Telephone control function buttons● Press the  PHONE  infotainment button to openthe PHONE main menu. Composition Touch, Composition Colour34
 CONFIDENTIAL not for distribution Function button: effect1Name of the paired mobile telephone or the user profile in use. Touch to connect or pair an-other mobile telephone.2Speed dial buttons which can be used to store one telephone number from the telephonebook each ⇒ page 38.Opens the keypad to enter a telephone number ⇒ page 36.Opens the telephone book in the paired mobile telephone ⇒ page 36.Opens the call lists in the paired mobile telephone ⇒ page 37.Opens the Telephone setup menu ⇒ page 38.Touch to accept a call.Touch to end a call.OR: touch to reject an incoming call.Touch to mute the ring tone during a call or to switch the mute off.Telephone control displays and symbolsDisplay: meaningAThe name of the mobile telephone network provider where the inserted SIM card or the SIMcard of the paired mobile telephone is registered.BDisplays the telephone number or the stored name.The charge level of the paired mobile telephone.The signal strength of the current mobile telephone transmitter station. During a telephone callFig. 26  During a telephone callFirst read and observe the introductoryinformation given on page 34.When a connection is made to a dialled telephonenumber, the PHONE main menu changes to thetelephone call view ⇒ Fig. 26.Displays and function buttons: action and effecta) Touch to make the call on the mobile telephone provision.Touch to switch off the microphone in the mobile telephone provision during a call (  func-tion button changes to  ). The conversation in the vehicle cannot be heard at the other end. appears on the display  A.Touch the   function button to switch on the microphone in the mobile telephone provisionagain.Touch to end a call. Telephone control (PHONE) 35142.5R6.RCT.20
 CONFIDENTIAL not for distribution Displays and function buttons: action and effectA: call is being made with the connected mobile telephone. Touch the   function button tomake the call on the mobile telephone provision.: the microphone in the provision for mobile telephone is switched off.: charge level of the paired mobile telephone.BDisplay of call duration and telephone number or the stored name.a) This function button is only displayed when the call is made on the mobile telephone. Entering a telephone numberFig. 27  Entering a telephone numberFirst read and observe the introductoryinformation given on page 34.In the PHONE main menu, press the   functionbutton.Possible functionsEntering a telephone num-berEnter the telephone number on the keypad.Touch the   function button to dial the number.Selecting a contact from alistEnter the first letters of the required contact on the keypad. Possible en-tries appear in the contact list.Browse through the contact list and touch the desired contact to make thecall. Telephone book menu (Contacts)Fig. 28  Contacts menu Fig. 29  Search windowFirst read and observe the introductoryinformation given on page 34. Composition Touch, Composition Colour36
 CONFIDENTIAL not for distribution It may take a few minutes after the first pairingprocess until the telephone book data1) from thepaired mobile telephone is available on the info-tainment system. The process could take up to anhour, depending on the amount of data to be trans-ferred. If necessary, confirm the transfer on themobile telephone.The telephone book can also be opened during anon-going telephone call.In the PHONE main menu, press the   functionbutton.Possible functionsSelecting a contact from alistBrowse through the list and touch the desired contact to make the call.OR: if several numbers are allocated to the same contact, first touch thecontact and then the desired number to make the call.Finding a contact in thesearch windowTouch the   ⇒ Fig. 28 function button to open the search window.Enter the name you are looking for in the search window ⇒ Fig. 29.The number of matching results is displayed to the right of the entry field.Touch the function button to go to the list view.Browse through the list and touch the desired contact to make the call.Availability of telephone book menu dependson the mobile telephone being used. Call lists menuFig. 30  Call list menuFirst read and observe the introductoryinformation given on page 34.● In the PHONE main menu, press the   func-tion button.● Touch the  ...  ⇒ Fig. 30  1 function button.● Select the desired call list:  All ,  Missed calls ,Dialled numbers  or  Received calls .If a telephone number is already stored in the tele-phone book, the stored name is displayed in thecall list instead of the telephone number.Possible displays in the call menuDisplay MeaningMissed calls : shows telephone numbers of missed and unanswered calls.Dialled numbers : shows telephone numbers that were dialled on the mobile telephone and theinfotainment system telephone control system.Received calls : shows all telephone numbers that were received on the mobile telephone andon the infotainment system via the telephone control system.Availability of call lists depends on the mobiletelephone being used. 1) Depending on what device is used, only contacts from the telephone memory may be loaded.Telephone control (PHONE) 37142.5R6.RCT.20
 CONFIDENTIAL not for distribution Speed dial buttonsFig. 31  PHONE main menuFirst read and observe the introductoryinformation given on page 34.One telephone number from the telephone bookcan be stored to each of the speed dial buttons⇒ Fig. 31  1.All speed dial buttons must be assigned manuallyand are then specific to a user profile.Possible functionsAssigning speed dial but-tonsIn the PHONE main menu, touch a free speed dial button.Select the desired contact from the list. If several telephone numbers arestored for the selected contact, select the desired number.Editing assigned speed di-al buttonsIn the PHONE main menu, press and hold an assigned speed dial buttonuntil the Contacts menu opens.Select the desired contact from the list. If several telephone numbers arestored for the selected contact, select the desired number.To close the Contacts menu without applying changes, touch the   func-tion button.Deleting assigned speeddial buttonsAny telephone number stored on a speed dial button can be deleted in theUser profile setup menu ⇒ page 39.Dialling with speed dialbuttonsIn the PHONE main menu, briefly touch an assigned speed dial button todial the telephone number stored to that button.Contacts stored to the speed dial buttons arenot updated automatically. If a contact storedto a speed dial button is modified on the mobile tel-ephone, the speed dial button must be assignedagain. Telephone settingsFirst read and observe the introductoryinformation given on page 34.In the PHONE main menu, touch the  Setup  func-tion button.Function button: effect Hands-free a): the hands-free function is activated. Touch the function button during a telephone call tomake the call on the mobile telephone.Select telephone : select the mobile telephone from the list view to connect it to the infotainment system. Find telephone : touch to connect a new mobile telephone.Bluetooth : opens the Bluetooth setup menu ⇒ page 39. Composition Touch, Composition Colour38
 CONFIDENTIAL not for distribution Function button: effectUser profile : opens the User profile setup menu ⇒ page 39.Select ring tone b): select the ring tone from the list of preset ring tones. The selected ring tone is played andstored when you leave the submenu.a) This function button is only active during a telephone call.b) Either the selected ring tone or the ring tone set in the mobile phone is sounded, depending on what mobile phone is being used. Bluetooth settings®First read and observe the introductoryinformation given on page 34.In the PHONE main menu, touch the  Setup  func-tion button and then  Bluetooth .Function button: effect Bluetooth : touch to switch Bluetooth® off. All existing connections are ended.Visibility : switch Bluetooth® visibility on and off. Visible : Bluetooth® visibility is activated. Not visible : Bluetooth® visibility is deactivated. The Bluetooth® visibility has to be switched onbefore a Bluetooth® device can be externally paired with the infotainment system. Upon start : Bluetooth® visibility is deactivated approximately 3 minutes after the engine is star-ted.Name : to display or edit the device name. This name is displayed to other Bluetooth® devices in theirBluetooth® settings.Paired devices : displays paired devices. Separating and connecting individual Bluetooth® devices andBluetooth® profiles.Find devices : finds Bluetooth® devices that are set to visible and are within the range of the infotainmentsystem. The maximum range is approximately 10 metres. Bluetooth audio (A2DP/AVRCP) : this function must be activated if you want to connect an external audiosource to the infotainment system via Bluetooth®⇒ page 28. User profile settingsFirst read and observe the introductoryinformation given on page 34.In the PHONE main menu, touch the  Setup  func-tion button and then  User profile .Function button: effectManage favourites : to edit speed dial buttons. Assigned speed dial button: touch to delete the stored number. Unassigned speed dial button: touch to store a number from the address book to the speeddial button.Sort by : set the sorting order for telephone book entries (Last name or First name).Import contacts : touch to import the address book from the connected telephone or to update the previouslyimported address book.Delete other profiles : to delete individual or all non-active user profiles. Telephone control (PHONE) 39142.5R6.RCT.20
 CONFIDENTIAL not for distribution SettingsMenu and system settings (SETUP)IntroductionThis chapter contains information on the followingsubjects:System settings main menu (Setup)  . . . . . . . . 40The range of possible settings depends on thecountry, the unit and the vehicle's equipment speci-fication.Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6● Basic information on use ⇒ page 7 System settings main menu (Setup)First read and observe the introductoryinformation given on page 40.● Press the  SETUP  infotainment button to openthe System setup main menu.● To adjust the settings for a certain function,touch the appropriate function button.Function button: effectRemove the SD card safely : ejects the memory card from the system. Once the memory card has been ejec-ted from the system the function button is greyed out.Sound : make sound and volume settings ⇒ page 42.Screen : make screen settings.  Display off (in 10 s) : when this function is activated, the screen switches off if no button is press-ed on the infotainment system for about ten seconds. The screen is switched back on by touch-ing the screen or pressing an infotainment button. Brightness : select the brightness of the screen.  Confirmation tone : activates the confirmation tone that sounds when a function button istouched.  Show clock in standby mode : the screen shows the current time when the infotainment system isin standby mode.Time and date : set the time and date. Time : to set the current time. Time format : select the format for the time display (12 or 24-hour).  Summer (DST) : summer time is activated. Date : set the current date. Date format : to select the format for the date display (DD.MM.YY, YY-MM-DD or MM-DD-YY).Language : select the desired language for text and voice output.Keypad : select the required layout (alphabetical or keyboard layout).More keypad languages : select additional keypad languages.Units : sets units of measurement for displays in the vehicle. Distance, Speed, Temperature, Volume, Consumption and Pressure.Bluetooth : make settings relating to Bluetooth® ⇒ page 39.Remove safely : disconnect data storage device (USB storage device or SD card) from the system. Oncethe storage device has been ejected from the system the respective function button is greyed out. Composition Touch, Composition Colour40
 CONFIDENTIAL not for distribution Function button: effectFactory settings : restoring the factory settings will erase entered data and settings depending on whichoption has been selected.System information : displays the system information (serial number, hardware and software versions).Copyright : copyright information.It is important that the correct date and timeare set in the vehicle to ensure the infotain-ment system works properly. Settings 41142.5R6.RCT.20
 CONFIDENTIAL not for distribution Sound and volume settingsIntroductionThis chapter contains information on the followingsubjects:Adjusting settings  . . . . . . . . . . . . . . . . . . . . . . . 42The range of possible settings depends on thecountry, the unit and the vehicle's equipment speci-fication.Additional information and warnings:● Safety information  for infotainment system⇒ page 3● Overview of the control elements ⇒ page 6● Basic information on use ⇒ page 7 Adjusting settingsFirst read and observe the introductoryinformation given on page 42.● Press the  SOUND  infotainment button.●OR: press the  SETUP  infotainment button andthen select  Sound  to open the Sound setup mainmenu.● To adjust the settings for a certain function,touch the appropriate function button.Changes are automatically stored when a menu isclosed.Function button: effectBass - Mid- Treble : sets the tonal quality (Bass - Mid - Treble).Balance  or  Balance - Fader : set the sound focus.The crosshair shows the where the sound is currently focused in the car's interior. To move the soundfocus, touch the required position on the interior view or use the arrow buttons to change the position. Toplace the focus of sound at the centre of the interior view, touch the function button between the arrows.Volume : to make volume settings. Max. switch-on volume : define the maximum volume at switch-on. Announcements : to set the output volume for announcements (e.g. traffic announcements). Speed-dep. vol. (GALA) : define the scope of the speed-dependent volume control. The audio vol-ume is automatically increased as the vehicle speed increases. Audio lower. : set how much the volume of the infotainment system should be reduced by whenthe ParkPilot is active. AUX volume : to set the output volume for audio sources that are connected via the AUX-IN mul-timedia socket (Quiet, Medium or Loud). Please also refer to ⇒ page 42, Adjusting playbackvolume of external audio sources. BT audio : to set the output volume for audio sources connected via Bluetooth® (quiet, mediumor loud). Please also refer to ⇒ page 42, Adjusting playback volume of external audio sour-ces. Confirmation tone : activates the confirmation tone that sounds when a function button is touched.Adjusting playback volume of external audiosourcesIf you need to increase the output volume of an ex-ternal audio source, first lower the base volume onthe infotainment system.If the sound from the external audio source is tooquiet, increase the output volume on the externalaudio source if possible. If this is not sufficient, setthe input volume to Medium or Loud.Composition Touch, Composition Colour42
 CONFIDENTIAL not for distribution If the sound from the connected external audiosource is too loud or distorted, lower the outputvolume on the external audio source if possible. Ifthis is not sufficient, set the input volume to Me-dium or Quiet.Settings 43142.5R6.RCT.20
 CONFIDENTIAL not for distribution AbbreviationsAbbreviation DefinitionGeneric technology for the transmission of audio signals via Bluetooth® (Advanced AudioDistribution Profile).Amplitude modulation (medium wave, MW).Auxiliary audio input.Universal technology for remote control of audio sources via Bluetooth® (Audio Video Re-mote Control Profile).German Standards Authority (Deutsches Institut für Normung).Digital rights management.Supporting of other networks (enhanced other network).Frequency modulation (very high frequency, VHF).Wireless telephony (hands-free profile).Format for compressing audio files.Radio data system.Traffic news function (traffic program).Variable bit rate.Format for compressing audio files.A2DPAMAUX-INAVRCPDINDRMEONFMHFPMP3RDSTPVBRWMA Composition Touch, Composition Colour44
 CONFIDENTIAL not for distribution IndexAAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Areas where special regulations apply  . . . . 31AUX-IN  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27AUX-IN socket  . . . . . . . . . . . . . . . . . . . . . . 27External audio sources  . . . . . . . . . . . . . . . 27Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . 23AUX-IN socket  . . . . . . . . . . . . . . . . . . . . . . . . 27BBase volume  . . . . . . . . . . . . . . . . . . . . . . . . . . 8Adjusting  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Muting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8BluetoothProfiles  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . 39Bluetooth audio  . . . . . . . . . . . . . . . . . . . . . . . 28Browsing lists  . . . . . . . . . . . . . . . . . . . . . . . . . 9BT audio  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Infotainment system . . . . . . . . . . . . . . . . . . . 6CCall lists  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37CDCannot be read  . . . . . . . . . . . . . . . . . . . . . 25Ejecting  . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Faulty  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Inserting  . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Mode  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . 23Checkboxes  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Control elements (infotainment system) . . . . 6Copyright  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Information  . . . . . . . . . . . . . . . . . . . . . . . . . 41Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10DDialling a number  . . . . . . . . . . . . . . . . . . . . . 36During a telephone call . . . . . . . . . . . . . . . . . 35EEjectsee CD  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25EON . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 44Explosion risk areasTelephone  . . . . . . . . . . . . . . . . . . . . . . . . . 31External audio sources . . . . . . . . . . . . . . . . . 27Adjusting playback volume  . . . . . . . . . . . . 42BT audio . . . . . . . . . . . . . . . . . . . . . . . . . . . 28External data storage deviceUSB  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26FFactory settings . . . . . . . . . . . . . . . . . . . . . . . 40FM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 44Frequency bandAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Changing  . . . . . . . . . . . . . . . . . . . . . . . . . . 12FM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . 12Function buttons  . . . . . . . . . . . . . . . . . . . . . . . 8MEDIA main menu  . . . . . . . . . . . . . . . . . . . 22Operating  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Radio main menu . . . . . . . . . . . . . . . . . . . . 12Function buttons (soft keys)PHONE main menu  . . . . . . . . . . . . . . . . . . 34GGALA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42HHard keys  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Hard keys (infotainment system) . . . . . . . . . . 6IIgnition offSwitch-off delay (timeout) . . . . . . . . . . . . . . . 7Infotainment buttons . . . . . . . . . . . . . . . . . . 6, 7Input window  . . . . . . . . . . . . . . . . . . . . . . . . . 10Interference from a mobile telephone  . . . . . . 7Introduction  . . . . . . . . . . . . . . . . . . . . . . . . . . . 3KKeypad  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10MMain menuMEDIA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22PHONE  . . . . . . . . . . . . . . . . . . . . . . . . . . . 34RADIO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Settings (SETUP) . . . . . . . . . . . . . . . . . . . . 40Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42MEDIAAUX-IN socket  . . . . . . . . . . . . . . . . . . . . . . 27Bit rate  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Index 45142.5R6.RCT.20
 CONFIDENTIAL not for distribution Bluetooth audio  . . . . . . . . . . . . . . . . . . . . . 28CD audio data  . . . . . . . . . . . . . . . . . . . . . . 20CD cannot be read . . . . . . . . . . . . . . . . . . . 25CD faulty  . . . . . . . . . . . . . . . . . . . . . . . . . . 25CD mode  . . . . . . . . . . . . . . . . . . . . . . . . . . 25Changing media source  . . . . . . . . . . . . . . . 23Changing tracks  . . . . . . . . . . . . . . . . . . . . . 24Copyright  . . . . . . . . . . . . . . . . . . . . . . . . . . 20Displays  . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Displays and symbols  . . . . . . . . . . . . . . . . 23Ejecting a CD  . . . . . . . . . . . . . . . . . . . . . . . 25External data storage device connected toUSB port  . . . . . . . . . . . . . . . . . . . . . . . . . 26Fast forward  . . . . . . . . . . . . . . . . . . . . . . . . 24Fast reverse  . . . . . . . . . . . . . . . . . . . . . . . . 24Function buttons  . . . . . . . . . . . . . . . . . . . . 22Inserting a CD  . . . . . . . . . . . . . . . . . . . . . . 25Inserting memory card  . . . . . . . . . . . . . . . . 26Main menu  . . . . . . . . . . . . . . . . . . . . . . . . . 22Media mode  . . . . . . . . . . . . . . . . . . . . . . . . 20Media source selection menu  . . . . . . . . . . 23Memory card cannot be read  . . . . . . . . . . . 26MP3 files  . . . . . . . . . . . . . . . . . . . . . . . . . . 20Playback modes . . . . . . . . . . . . . . . . . . . . . 22Playing order  . . . . . . . . . . . . . . . . . . . . . . . 21Playlists  . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Preparing for removal  . . . . . . . . . . . . . . . . 26Random play (Mix) . . . . . . . . . . . . . . . . . . . 22Removing memory card . . . . . . . . . . . . . . . 26Repeat function (Repeat) . . . . . . . . . . . . . . 22Requirements . . . . . . . . . . . . . . . . . . . . . . . 20Restrictions  . . . . . . . . . . . . . . . . . . . . . . . . 21Scan function (SCAN)  . . . . . . . . . . . . . . . . 22Selecting storage devices  . . . . . . . . . . . . . 23Selecting track  . . . . . . . . . . . . . . . . . . . . . . 24Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Track information  . . . . . . . . . . . . . . . . . . . . 23Track list . . . . . . . . . . . . . . . . . . . . . . . . . . . 24WMA files  . . . . . . . . . . . . . . . . . . . . . . . . . . 20Media sources  . . . . . . . . . . . . . . . . . . . . . . . . 23AUX-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23CD  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Memory card  . . . . . . . . . . . . . . . . . . . . . . . 23Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . 23Memory cardCannot be read  . . . . . . . . . . . . . . . . . . . . . 26Inserting  . . . . . . . . . . . . . . . . . . . . . . . . . . . 26Preparing memory card for removal  . . . . . 26Removing . . . . . . . . . . . . . . . . . . . . . . . . . . 26Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . 23Muting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8NNumbersDialling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36OOn-screen keypad  . . . . . . . . . . . . . . . . . . . . . 10OperationAdditional display information  . . . . . . . . . . . 11Adjusting the volume  . . . . . . . . . . . . . . . . . . 8Browsing lists  . . . . . . . . . . . . . . . . . . . . . . . . 9Checkboxes  . . . . . . . . . . . . . . . . . . . . . . . . . 8Entries  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Function buttons  . . . . . . . . . . . . . . . . . . . . . 8Infotainment buttons  . . . . . . . . . . . . . . . . . . 7Input window  . . . . . . . . . . . . . . . . . . . . . . . 10Muting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8On-screen keypad  . . . . . . . . . . . . . . . . . . . 10PHONE  . . . . . . . . . . . . . . . . . . . . . . . . 30, 34RADIO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Rotary/push knobs  . . . . . . . . . . . . . . . . . . . . 7Scrolling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Slider  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Switching on and off . . . . . . . . . . . . . . . . . . . 7Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . 8PPHONEA2DP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Areas where special regulations apply  . . . 31Bluetooth profiles  . . . . . . . . . . . . . . . . . . . . 31Bluetooth settings  . . . . . . . . . . . . . . . . . . . 39Call lists  . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Connecting via infotainment system  . . . . . 32Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Description of functions  . . . . . . . . . . . . . . . 31Dialling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Displays and symbols  . . . . . . . . . . . . . . . . 35During a telephone call  . . . . . . . . . . . . . . . 35Entering telephone number  . . . . . . . . . . . . 36Explosion risk areas . . . . . . . . . . . . . . . . . . 31Function buttons  . . . . . . . . . . . . . . . . . . . . 34General information  . . . . . . . . . . . . . . . . . . 31HFP  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Main menu  . . . . . . . . . . . . . . . . . . . . . . . . . 34Mobile telephone pairing  . . . . . . . . . . . . . . 32Pairing via infotainment system  . . . . . . . . . 32Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Speed dial buttons  . . . . . . . . . . . . . . . . . . . 38Telephone book  . . . . . . . . . . . . . . . . . . . . . 36Telephone control . . . . . . . . . . . . . . . . . . . . 30Telephone control system  . . . . . . . . . . . . . 34User profile settings  . . . . . . . . . . . . . . . . . . 39PlaybackAUX-IN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27CD  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25External data storage device (USB) . . . . . . 26MEDIA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Memory card  . . . . . . . . . . . . . . . . . . . . . . . 22RADIO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Track  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Composition Touch, Composition Colour46
 CONFIDENTIAL not for distribution Pop-up windows  . . . . . . . . . . . . . . . . . . . . . . . 8QQuick reference guide . . . . . . . . . . . . . . . . . . . 3RRADIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12AM settings  . . . . . . . . . . . . . . . . . . . . . . . . 18Display of station names  . . . . . . . . . . . . . . 13Displays and symbols  . . . . . . . . . . . . . . . . 13EON  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17FM settings  . . . . . . . . . . . . . . . . . . . . . . . . 18Frequency change  . . . . . . . . . . . . . . . . . . . 12Function buttons  . . . . . . . . . . . . . . . . . . . . 12Main menu  . . . . . . . . . . . . . . . . . . . . . . . . . 12Radio mode  . . . . . . . . . . . . . . . . . . . . . . . . 12Radio text . . . . . . . . . . . . . . . . . . . . . . . . . . 16RDS  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Scan function (SCAN)  . . . . . . . . . . . . . . . . 16Selecting stations . . . . . . . . . . . . . . . . . . . . 14Settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Setting station frequency  . . . . . . . . . . . . . . 14Setting stations  . . . . . . . . . . . . . . . . . . . . . 14Station buttons  . . . . . . . . . . . . . . . . . . . . . . 14Station list  . . . . . . . . . . . . . . . . . . . . . . . . . 14Station tracking via RDS  . . . . . . . . . . . . . . 13Stopping station name scrolling  . . . . . . . . . 16Storing stations  . . . . . . . . . . . . . . . . . . . . . 14TP (traffic program)  . . . . . . . . . . . . . . . . . . 17Traffic announcement (INFO)  . . . . . . . . . . 17Traffic news  . . . . . . . . . . . . . . . . . . . . . . . . 17Radio text (RDS)  . . . . . . . . . . . . . . . . . . . . . . 16Random play (Mix) . . . . . . . . . . . . . . . . . . . . . 22RDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Automatic station tracking  . . . . . . . . . . . . . 13Radio text . . . . . . . . . . . . . . . . . . . . . . . . . . 16RDS Regional  . . . . . . . . . . . . . . . . . . . . . . 13TP (traffic program)  . . . . . . . . . . . . . . . . . . 17Repeat  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Repeat function (Repeat)  . . . . . . . . . . . . . . . 22Requirements forCDs  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20memory cards  . . . . . . . . . . . . . . . . . . . . . . 20Rotary/push knobs  . . . . . . . . . . . . . . . . . . . . . 7Rotary/push knobs (infotainment system)  . . 6SSafety informationInfotainment system . . . . . . . . . . . . . . . . . . . 3SCANMedia  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Radio  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Scan function (SCAN)MEDIA  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22RADIO  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16ScreenOperating  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Screen (infotainment system)  . . . . . . . . . . . . 6Scrolling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9SD cardsee Memory card  . . . . . . . . . . . . . . . . . . . . 26Setting date  . . . . . . . . . . . . . . . . . . . . . . . . . . 40SettingsAM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Bluetooth  . . . . . . . . . . . . . . . . . . . . . . . . . . 39Defaults  . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Factory settings  . . . . . . . . . . . . . . . . . . . . . 40FM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Main menu  . . . . . . . . . . . . . . . . . . . . . . . . . 40Media  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28Menu and system settings  . . . . . . . . . . . . . 40PHONE  . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Radio  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42System  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40User profile . . . . . . . . . . . . . . . . . . . . . . . . . 39Volumes  . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Setting time  . . . . . . . . . . . . . . . . . . . . . . . . . . 40SETUPsee Settings  . . . . . . . . . . . . . . . . . . . . . . . . 40Slider  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Soft keysInfotainment system . . . . . . . . . . . . . . . . . . . 8MEDIA main menu  . . . . . . . . . . . . . . . . . . . 22Radio main menu . . . . . . . . . . . . . . . . . . . . 12Sound focus (balance, fader)  . . . . . . . . . . . . 42Sound settings (treble, bass)  . . . . . . . . . . . . 42Speed-dependent volume . . . . . . . . . . . . . . . 42Speed dial buttons  . . . . . . . . . . . . . . . . . . . . 38Station buttons  . . . . . . . . . . . . . . . . . . . . . . . 14Station names  . . . . . . . . . . . . . . . . . . . . . . . . 13StationsScan function (SCAN)  . . . . . . . . . . . . . . . . 16Selecting  . . . . . . . . . . . . . . . . . . . . . . . . . . 14Setting  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Stopping station name scrolling  . . . . . . . . . 16Storing  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Station search  . . . . . . . . . . . . . . . . . . . . . . . . 16Station tracking  . . . . . . . . . . . . . . . . . . . . . . . 13Switch-off delay (timeout) . . . . . . . . . . . . . . . . 7Switching off  . . . . . . . . . . . . . . . . . . . . . . . . . . 7Switching on  . . . . . . . . . . . . . . . . . . . . . . . . . . 7TTelephone controlsee PHONE  . . . . . . . . . . . . . . . . . . . . . . . . 30Index 47142.5R6.RCT.20
 CONFIDENTIAL not for distribution Telephone control system (PHONE)Switching off . . . . . . . . . . . . . . . . . . . . . . . . 33Text input  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Things to noteAUX operation  . . . . . . . . . . . . . . . . . . . . . . 27Displays  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Volume reduction  . . . . . . . . . . . . . . . . . . . . . 7Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Touchscreen (infotainment system)  . . . . . . . 6TP (traffic program)EON  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Switching on and off . . . . . . . . . . . . . . . . . . 17Traffic announcement (INFO)  . . . . . . . . . . 17Track list  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Traffic announcement (INFO)  . . . . . . . . . . . . 17Traffic newssee TP (traffic program)  . . . . . . . . . . . . . . . 17UUnit buttons  . . . . . . . . . . . . . . . . . . . . . . . . . . . 7USBConnecting an external data storage device  . .26Disconnecting  . . . . . . . . . . . . . . . . . . . . . . 26Not readable  . . . . . . . . . . . . . . . . . . . . . . . 26User profileSettings  . . . . . . . . . . . . . . . . . . . . . . . . . . . 39VVHFsee FM  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44VolumeAdjusting  . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Base volume  . . . . . . . . . . . . . . . . . . . . . . . . 8Determining for external audio sources  . . . 42Speed-dependent volume increase (GALA)  . .42Traffic announcements . . . . . . . . . . . . . . . . 42Volume distribution (balance, fader)  . . . . . . 42Volume reduction  . . . . . . . . . . . . . . . . . . . . . . 7Composition Touch, Composition Colour48FCC Information to UserThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.• Consult the dealer or an experienced radio/TV technician for help.CautionModifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu