LG Electronics USA LGHALCW1502 WLAN Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2529471
Application ID	vApXvNPGNw1v5JRbccyclw==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	21.81kB (272614 bits)
Date Submitted	2015-02-10 00:00:00
Date Available	2015-08-10 00:00:00
Creation Date	2015-02-10 18:47:04
Producing Software	Microsoft® Word 2013
Document Lastmod	2015-02-10 18:47:04
Document Title	Users Manual
Document Creator	Microsoft® Word 2013
Document Author:	LG

1. User Manual
This user manual gives a brief overview of how to use LCW-002 Wi-Fi Module.
2. Product Overview
LCW-002 Wi-Fi Modem provides the connectivity between users and product. This allows
a user to manage and control product and monitor product status from the outside of the
house using Smartphone or notebook.
LCW-002 Wi-Fi Modem is installed in home appliances.
3. Specifications
- WLAN Standard : 802.11 b/g/n
- Host Interface : UART Interface
- Operating Tempeature : 0 ~ 40℃
- Operating Voltage : 4.5V ~ 5.5V
4. Function Block
▣ Block Diagram
1) Wi-Fi
- SoC Module including Microcontroller and Wi-Fi chipset
2) Level shift circuits
- Signal level shift circuits to communicate between appliance and AW-CU282 Wi-Fi module by
UART interface.
3) DC-DC Converter
- DC 5V converted to DC 3.3V
4) Main Connector
- Connect Wi-Fi modem with appliance
5. Product Registration and Wi-Fi Setup
1) Download and install LG App offered by the App store.
2) Run the LG App and proceed to sign up.
3) Enter the required information.
4) Proceed to register your product
5) Set the AP information.
6) LG App will automatically set up Wi-Fi settings of the LCW-002 Modem.
7) LCW-002 Modem is connected to AP.
6. Warning Statement

FCC Part 15.19 Statements:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Part 15.105 statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Part 15.21 statement
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
RF Exposure Statement
The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is
maintained between the radiator (antenna) and all persons at all times. This device must not be co-located
or operating in conjunction with any other antenna or transmitter.
End Product Labeling
The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC
Certification Number are not visible when the module is installed inside another device, then the
outside of the device into which the module is installed must also display a label referring to the
enclosed module. In that case, the final end product must be labeled in a visible area with the
following:
“Contains FCC ID: BEJ-LGHALCW1502”
“Contains IC: 2703N-LGHALCW1502”

RSS-GEN, Sec. 7.1.3 – (licence-exempt radio apparatus)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de
brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
RF Exposure
The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20
cm between the radiation source (antenna) and any individual. This device may not be installed or used in
conjunction with any other antenna or transmitter.
l'exposition aux RF
L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de
au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void
your authority to operate thisequipment.Attention:
Les changements ou modifications de cet appareil non expressément approuvé par le fabricant peuvent
annuler votre droit à utiliser cet équipement.
É tiquetage du produit final (IC)
Le module BT111 est étiqueté avec sa propre identification FCC et son propre numéro de
certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque
le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel
le module est installé devra également présenter une étiquette faisant référence au module inclus.
Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations
suivantes :
« Contient module émetteur identification FCC ID : BEJ-LGHALCW1502
« Contient module émetteur IC : 2703N-LGHALCW1502”
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module or change RF related parameters in the user manual
of the end product.
OEM Responsibilities to comply with FCC and Industry Canada Regulations
The module has been certified for integration into products only by OEM integrators under
the following condition:
- The transmitter module must not be co-located or operating in conjunction with any other
antenna or transmitter except in accordance with FCC multi-transmitter product procedures.
As long as the two condition above is met, further transmitter testing will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed (for example, digital
device emissions, PC peripheral requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can’t be met (for certain configurations
or co-location with another transmitter), then the FCC and Industry Canada authorizations are
no longer considered valid and the FCC ID and IC Certification Number can’t be used on the
final product. In these circumstances, the OEM integrator will be responsible for re-evaluating
the end product (including the transmitter) and obtaining a separate FCC and Industry Canada
authorization.
Responsabilités des OEM quant à la conformité avec les réglementations de FCC et d’
Industrie Canada
Les modules ont été certifiés pour entrer dans la fabrication de produits exclusivement réalisés
par des intégrateurs dans les conditions suivantes :
- Le module transmetteur ne doit pas être installé ou utilisé en concomitance avec une autre
antenne ou un autre transmetteur.
Tant que ces deux conditions sont réunies, il n’est pas nécessaire de procéder à des tests
supplémentaires sur le transmetteur. Cependant, l’intégrateur est responsable des tests
effectués sur le produit final afin de se mettre en conformité avec d’éventuelles exigences
complémentaires lorsque le module est installé (exemple : émissions provenant d’appareils
numériques, exigences vis-à-vis de périphériques informatiques, etc.)
REMARQUE IMPORTANTE : En cas d’inobservance de ces conditions (en ce qui concerne
certaines configurations ou l’emplacement du dispositif à proximité d’un autre émetteur), les
autorisations de FCC et d’Industrie Canada ne seront plus considérées valables et
l’identification de FCC et le numéro de certification d’IC ne pourront pas être utilisés sur le
produit final. Dans ces cas, l’intégrateur OEM sera chargé d’évaluer à nouveau le produit final
(y compris l’émetteur) et d’obtenir une autorisation indépendante de FCC et d’Industrie
Canada.
- Dans le guide d’utilisation du produit final, l’intégrateur OEM doit s’abstenir de fournir des
informations à l’utilisateur final portant sur les procédures à suivre pour installer ou retirer ce
module RF ou pour changer les paramètres RF.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 5
Language                        : ko-KR
Tagged PDF                      : Yes
Author                          : LG
Creator                         : Microsoft® Word 2013
Create Date                     : 2015:02:10 18:47:04+09:00
Modify Date                     : 2015:02:10 18:47:04+09:00
Producer                        : Microsoft® Word 2013

EXIF Metadata provided by EXIF.tools