LG Electronics USA LGS512RX RF module User Manual

LG Electronics USA RF module

User Manual

Order Number : GETEC-C1-15-602 FCC Part 15 subpart C Test Report Number : GETEC-E3-15-046 Page 1 / 1 EUT Type: RF Module(RX) FCC ID.: BEJLGS512RX APPENDIX H : USER’S MANUAL
[ENGLISH] S512 RF Module(Rx) User Information (Model Name: EAT63294901) Contents 1. Overview and specification of the S512 RF Module(Rx) (1) Overview (2) Specification 2. Install Guide 3. Pin Description 4. Precautions 5. Customer Support (1) Overview This RF module is installed on the main board of the vacuum cleaner. It is a receiver that controls the vacuum cleaner by working with the transmitter which is installed on the handle of the vacuum cleaner using the 2.4GHz wireless band. (2) Specification Categories Details Model No. EAT63294901 Range of frequency 2405~2476 MHz Channel 16 Channel Transmission output 6 dBm Reception sensitivity –89 dBm Weight 1.42g (Tolerance±0.5g, excluding battery) Power source DC 5V Operational temperature range 0 ℃ ~ + 40 ℃ 1. Overview and specification of the S512 RF Module(Rx)
Connector is connected to the body of the vacuum cleaner then inserted into the module. Not an escape module, as shown below is mounted on the vacuum cleaner. Pin No Pin name I/O Pin Description 1 VBUS5 - VDD 5V 2 GND - Ground 3 GND - Ground 4 GP2 I/O UART_TX 5 GP10 I/O WAKE-UP_OUT 6 GP4 I/O UART_RX 7 DM I/O WAKE-UP_IN Bottom view Installed position 2. Install Guide 3. Pin Description
4. Precautions (1) Start using the vacuum cleaner by first pairing it with the handle, as instructed in the user manual. (2) Do not dismantle or exert heat to the product. (3) Do not drop the product or exert extreme impact that may even cause the case to be damaged. (4) Do not immerse the product in water. 5. Customer Support OHSUNG ELECTRONICS CO.,LTD. T.054-461-3647
Regulatory Notices1. FCCFCC Statements:This device complies with Part 15 of the FCC Rules. Operation is subject to the following Two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that maycause undesired operation.End Product LabelingThe module is labeled with its own FCC ID Number. If the FCC IDCertification Number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:“Contains FCC ID: BEJLGS512RX”The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product.OEM Responsibilities to comply with FCC RegulationsThe module has been certified for integration into products only by OEM integrators under the following condition:- The antenna(s) must be installed such that a minimum separation distance of at least 5 cm ismaintained between the radiator (antenna) and all persons at all times.- The transmitter module must not be co-located or operating in conjunction with any otherantenna or transmitter except in accordance with FCC multi-transmitter product procedures.As long as the two condition above is met, further transmitter testing will not be required.However, the OEM integrator is still responsible for testing their end-product for any additionalcompliance requirements required with this module installed (for example, digital deviceemissions, PC peripheral requirements, etc.).IMPORTANT NOTE: In the event that these conditions can’t be met (for certain configurations orco-location with another transmitter), then the FCC authorizations is nolonger considered valid and the FCC ID Number can’t be used on the finalproduct. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining an authorization.WarningChanges or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.Note : The manufacturer is not responsible for any Radio or TV interferencecaused by unauthorized modifications to this equipment. Such modificationscould void the user's authority to operate the equipment.Federal Communication Commission (FCC) Radiation Exposure statementThe device and the antenna for this device must be installed to ensure aminimum separation distance of 20 cm more from a person's body. Otheroperating configurations should be avoided.

Navigation menu