LG Electronics USA LGS610TX DUST RF MODULE User Manual EMISSION TEST REPORT

LG Electronics USA DUST RF MODULE EMISSION TEST REPORT

User Manual

Order Number : GETEC-C1-17-087 FCC Part 15 subpart C Test Report Number : GETEC-E3-17-002 Page 1 / 1 APPENDIX H : USER’S MANUALEUT Type: DUST RF MODULE FCC ID.: BEJLGS610TX
[ENGLISH] S610 RF Module(Tx) User Information(Model Name: EAT63294801) Contents 1. Overview and specification (1) Overview (2) Specification 2. Precautions3. Customer Support(1) 개 요 This RF module is installed on the dust sensor board of the vacuum cleaner. It is a transmitter that controls the vacuum cleaner by working with the receiver which is installed on the main board of the vacuum cleaner using the 2.4GHz wireless band. (2) 제 원 구 분 내 용 Model No. EAT63613801 Range of frequency 2405~2476 MHz Channel 16 Channel Transmission output 6 dBm Reception sensitivity –89 dBmWeight 2.42g (Tolerance±0.5g, excluding battery) Power source AAA x 2EA, (2 alkaline batteries are used) Operational temperature range 0 ℃ ~ + 40 ℃ 1. Overview and specification
2. Precautions(1) After replacement of the battery, use the handle following pairing in accordance with user manual. (2) If the unit does not operate after replacement of battery, take the battery out and reattempt pairing in accordance with the user manual. (3) If the remote control is not being used for prolonged period of time, it is recommendable to remove the battery from the unit. (4) Do not dismantle or exert heat to the battery. (5) Do not drop battery or exert extreme impact that may even cause the case to be damaged. (6) Do not immerse the battery in water. (7) There is danger of explosion if the battery is inserted reversely. (8) Discard the used battery into designated location. 3. Customer SupportRefer to the contact number for services provided in the Vacuum cleaner Manual.
Regulatory Notices1. FCCFCC Statements:This device complies with Part 15 of the FCC Rules. Operation is subject to the following Two conditions:(1) this device may not cause harmful interference, and(2) this device must accept any interference received, including interference that maycause undesired operation.End Product LabelingThe module is labeled with its own FCC ID Number. If the FCC IDCertification Number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following:“Contains FCC ID: BEJLGS610TX”The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module or change RF related parameters in the user manual of the end product.OEM Responsibilities to comply with FCC RegulationsThe module has been certified for integration into products only by OEM integrators under the following condition:- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times.- The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additionalcompliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).IMPORTANT NOTE: In the event that these conditions can’t be met (for certain configurations orco-location with another transmitter), then the FCC authorizations is nolonger considered valid and the FCC ID Number can’t be used on the finalproduct. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining an authorization.WarningChanges or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.Note : The manufacturer is not responsible for any Radio or TV interferencecaused by unauthorized modifications to this equipment. Such modificationscould void the user's authority to operate the equipment.Federal Communication Commission (FCC) Radiation Exposure statementThis remote device is approved as a hand-held and hand-operated only portable (relative to hand) device which is normally operated at 20 cm from a person's body.

Navigation menu