LG Electronics USA LGSWFAC73 RF Module User Manual
LG Electronics USA RF Module
Contents
- 1. User Manual
- 2. Host User Manual - Part 1
- 3. Host User Manual - Part 2
User Manual
User Manual PRODUCT NAME : RF Module MODEL NAME : TWCM-B303D(LGSWFAC73) The information contained herein is the exclusive property of LG Innotek and shall not be distributed, reproduced or disclosed in whole or no in part without prior written permission of LG Innotek. (00)-0073 DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 1 / 11 Index No Description Page Features Picture of Product Installation Manual Block Diagram Absolute Maximum Ratings Operating Conditions Standard Test Conditions Pin Description Out Drawing 10 Packing Information 11 Regulatory Notices 10 Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 2 / 11 1. Features TWCM-B303D is the small size and low power module for IEEE 802.11ac wireless LAN. TWCM-B303D is based on Broadcom BCM43569 solution. IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructure Size : 68.0mm x 38.0mm Two stream spatial multiplexing up to 300Mbps(802.11n)/ 867Mbps(802.11ac) FPCB wireless Antenna for WLAN Use on-chip OTP (One-Time Programmable) Host Interface : USB2.0 Security : WAPI, WEP, WPA, WPA2, WMM, AES, WEP, TKIP, CKP Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB, Monitor 2. Picture of Product * BT was disabled by S/W. Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 3 / 11 3. Installation Manual Monitor Rear Panel TWCM-B303D installed position Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 4 / 11 REV. DATE : 2016.06.20 4. Block Diagram USB Hub Clock_(24MHz) 5G SPDT 2x2 Radio 802.11ac PHY Security 2G SPDT Connector Diplexer Diplexer 2G SPDT WLAN USB 2.0 802.11ac MAC Internal Bus ANT0 5G SPDT USB HUB BCM43569 ANT1 GPIO OTP 3.3V Serial Flash (1M) Main Clock(40MHz) 5. Absolute Maximum Ratings Caution : The specifications in Table 1 define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device. Parameter Min Max Unit Storage Temperature -20 +80 ℃ Storage Humidity (40℃) 90 . Other conditions 1) Do not use or store modules in the corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperature and relative humidity do not exceed 5 to 40℃ and 20 to 60%. 3) Assemble the modules within 6 months. Check the soldering ability in case of 6 months over. Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 5 / 11 6. Operating Conditions Parameter Min Typ Max Unit Ambient Temperature 60 ℃ Ambient Humidity (40℃) 85 Supply Voltage 4.75 5.0 5.25 Vdc 7. Standard Test Conditions The Test for electrical specification shall be performed under the following condition Otherwise this following conditions, not guaranteed this performance. 7-1. Ambient condition Temparature 25 ± 5℃ Humidity 65 ± 5% 7-2. Power supply voltages Input Voltage Supply Voltage VDD_3.3V +3.3V ±0.165V Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 6 / 11 8. Pin Description Pin No. Pin Name I/O Pin Description GND Ground BT_REG_ON BT Regulator ON 3D_Sync 3D_Sync WL_HOST_WAKE Wake On WLAN GND Ground USB D+ I/O USB Communication signal USB D+ USB D- I/O USB Communication signal USB D- VCC VDD 3.3V Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 7 / 11 9. Outline Drawing TWCM-B303D Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 8 / 11 10. Packing Information Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 9 / 11 TWCM-B303D Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 10 / 11 Regulatory Notices 1. FCC FCC Part 15.19 Statements: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.21 statement Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Part 15.105 statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. OEM Responsibilities to comply with FCC and Industry Canada Regulations The module has been certified for integration into products only by OEM integrators under the following condition: - The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. - The transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. - This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band. As long as the two condition above is met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). End Product Labeling The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC Certification Number are not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. In that case, the final end product must be labeled in a visible area with the following: “Contains FCC ID: BEJLGSWFAC73 “Contains IC: 2703H-LGSWFAC73 Copyrightⓒ. 2016. All Rights Reserved. DOCUMENT No : User Manual REG. DATE : 2016.06.20 REV. DATE : 2016.06.20 REV.NO : v1.0 MODEL NAME: TWCM-B303D(LGIT) LGSWFAC73 (LGE) PAGE : 11 / 11 2. IC RSS-GEN, Sec. 7.1.3 – (licence-exempt radio apparatus) This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF Exposure The antenna (or antennas) must be installed so as to maintain at all times a distance minimum of at least 20 cm between the radiation source (antenna) and any individual. This device may not be installed or used in conjunction with any other antenna or transmitter. This device is restricted to indoor use only within the 5.15 ~ 5.25GHz Band. l'exposition aux RF L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate thisequipment.Attention: Les changements ou modifications de cet appareil non expressément approuvé par le fabricant peuvent annuler votre droit à utiliser cet équipement. Étiquetage du produit final (IC) Le module est étiqueté avec sa propre identification FCC et son propre numéro de certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel le module est installé devra également présenter une étiquette faisant référence au module inclus. Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations suivantes : « Contient module émetteur identification FCC ID : BEJLGSWFAC73 « Contient module émetteur IC : 2703H-LGSWFAC73” 3. CE Hereby, ' LG Electronics USA, Inc.' declares that this LGSWFAC73 is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. Copyrightⓒ. 2016. All Rights Reserved.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Author : Create Date : 2016:06:20 10:32:55Z Modify Date : 2016:08:01 10:36:12+09:00 Subject : Microsoft PowerPoint - 6-1-LGSWFAC73(TWCM-B303D)_UserManual(English)_160620-ppt [호환 모드] Has XFA : No XMP Toolkit : Adobe XMP Core 5.6-c015 84.158975, 2016/02/13-02:40:29 Format : application/pdf Creator : Description : Microsoft PowerPoint - 6-1-LGSWFAC73(TWCM-B303D)_UserManual(English)_160620-ppt [호환 모드] Title : (Microsoft PowerPoint - 6-1.LGSWFAC73\(TWCM-B303D\)_UserManual\(English\)_160620.ppt [\310\243\310\257 \270\360\265\345]) Creator Tool : nPDF, http://iblogbox.com/npdf Metadata Date : 2016:08:01 10:36:12+09:00 Keywords : Producer : nPDF, http://iblogbox.com/npdf Document ID : uuid:38175b2e-e221-41b0-94d0-8ade858643bb Instance ID : uuid:01fb13b7-79ba-40c4-b874-b16a42570a6a Page Count : 12EXIF Metadata provided by EXIF.tools