LG Electronics USA LM568E 15-inch LCD Monitor User Manual Attachments

LG Electronics USA 15-inch LCD Monitor Attachments

Users Manual

2001 PCTEST LAB ATTACHMENT J — USER’S MANUAL
P/NO : 3828TUL193T (S-0107) Printed in KoreaPlease read this manual carefully before operating your set.Retain it for future reference.Record model number and serial number of the set.See the label attached on the back cover and quote thisinformation to your dealer when you require service.http://www.lge.comColor MonitorLCD 568LMUser’s Guide
A1IntroductionThe Monitor has an active matrix TFT (Thin-Film Transistor) LCD (LiquidCrystal Display).This monitor is designed for use in small working areas or for those who needmore working space on the desk.FeaturesThe Monitor is a 15inch (15 inches viewable) intelligent micropro-cessor basedmonitor. Digitally controlled auto-scanning is done with the microprocessor for horizontalscan frequencies between 31 and 61kHz, and vertical scan frequenciesbetween 56 and 75Hz. The microprocessor-based digital controls allow you to adjust conveniently avariety of image controls by using the OSD (On Screen Display).The monitor is shipped with 14 factory pre-programmed video modes that arepermanently resident. In addition, there are 16 user-storable modes, for a totalof 30 memory modes.Plug and play capability if supported by your system.This monitor has DDC 2B function.*Compliant with the following regulated specifications :*-EPA ENERGY STAR-Swedish TCO’99ENGLISH*For detailed information, please refer to the Reference Guide provided .
Connecting the MonitorA2To set up the monitor, ensure that the power is turned off to the monitor,computer system, and other attached devices, then follow these steps:Place the monitor in a convenient, well-ventilated location near your computer.Power off both the monitor and Computer.Slightly press and pull the latch on Stand cover.Connect the end of monitor signal cable to the connector at the rear panelof your monitor throught the slot and cable holder on Stand. Connect the otherend to the 15-pin connector on the rear panel of the computer and tighten thescrews. Be sure the signal cable aligns with the 15-pin connector.Connect the end of monitor signal cable to the connector at the rear panelof your monitor throught the slot and cable holder on Stand. Connect the otherend of the monitor signal cable to the rear panel of Macintosh computerthrough a Macintosh adapter and then tighten screws.Connect the plug from the AC adapter into the base of the monitor.Connect one end of the AC power cord to the AC adapter and the otherend to a properly grounded AC outlet that is easily accessible and close to themonitor.After connecting cables, put stand cover correctly into the holes unders stand.If securely connected, you can hear click sound from the latch.Power ON the PC, then the monitor.If you see the NO SIGNAL message, check the signal cable and connectors. After using the system, power OFF the monitor, then the PC.43211IBM PCMACINTOSHD-15PMac Adapter12344'5678924VAUDIODC OUTPower CordSignal Cable AC adapterD-15P3412Stand coverLatch*NOTE : If you see the “OUT OFRANGE” message, check to makesure your system is set to one of thefactory preset modes.(see page A9)
A3Connecting the Monitor24VAUDIODC OUTConnection the Audio
A4Location and Function of ControlsRear ViewFront ViewAUTOVOLMUTE MENUSET24VAUDIODC OUTD-Sub Signal ConnectorStand CoverPower ButtonPower IndicatorMENU ButtonMUTE ButtonButtonsAUTO/SET ButtonDC Power Connecter-+12VVESA wall mountingConnected to another object (stand type and wall-mounted type- optional)Kensington Security SlotConnected to a lockingcable that can bepurchased separately atmost computer storesNOTE : This monitor accept a 75mm x 75mm VESA-compliant mounting interface pad.
A5Control Panel FunctionFront Panel ControlsAUTOVOLMUTE MENUSETUse this button to enter and from the onscreen display (OSD).Use this button to turn the audio on or off.Use these buttons to choose or adjust items inthe on screen display.MENU ButtonMUTE ButtonButtonsThis indicator lights up green when themonitor operates normally. If the monitor is inDPM (Energy Saving) mode (stand-by/suspend/power off), this indicator colorchanges to amber.Power (DPMS)IndicatorUse this button to turn the monitor on or off.Power ButtonUse this button to enter a selection in the onscreen display.* AUTO adjustment functionTouch the AUTO/SET button before using OSD menu.This button is for the automatic adjustment of the screenposition, clock and phase. Note: Some signal from some graphics boards may not functionproperly. If the results are unsatisfactory, adjust your monitor’sPosition, Clock and Phase manually.AUTO/SETButtonControl FunctionMUTE ButtonMENU Button AUTO/SET ButtonPower ButtonPower (DPMS) IndicatorButtonsPROCESSINGAUTO CONFIGURATIONMENUMUTEVOLAUTOSET
A6Making adjustments to the image size, position and operating parameters ofthe monitor are quick and easy with the On Screen Display Control system. Aquick example is given below to familiarize you with the use of the controls.Following section is an outline of the available adjustments and selections youcan make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the MENU Button, then the main menu of the OSD appears.To access a control, use the Buttons. When the icon you wantbecomes highlighted, press the AUTO/SET Button.Use the Buttons to adjust the item to the desired level.Accept the changes by pressing the AUTO/SET Button.Exit the OSD by Pressing the MENU Button.On Screen Display (OSD) Control AdjustmentNOTEAllow the monitor to stabilize for at least 30 minutes before making image adjustment.1123456712234567123345671234456712345567
A7On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selection and adjusting an itemusing the OSD system. Listed below are the icons, icon names, and icondescriptions of the items that are shown on the Menu.OSD Adjust Description88100BRIGHTNESS CONTRAST9300K 6500KCOLORPRESET REDGREENBLUE6139POSITIONBrightnessUsed to adjust the brightness of thescreen. Contrast Adjust the display to the contrastdesired. PRESETREDGREENBLUE9300K/ 6500KTo appear the displays colortemperature.• 9300K:Slightly bluish white.• 6500K:Slightly reddish white.To set your own color levels.To set your own color levels.To set your own color levels.Vertical PositioTo move image up and down.Horizontal PositionTo move picture image left and right.
A8On Screen Display(OSD) Selection and Adjustment OSD Adjust DescriptionTRACKINGCLOCKPHASEBASSBALANCETREBLEVOLUMEAUDIO LANGUAGE ENGLISHOSD POSITION1024x768/70HzPRESET MODESETUPBEEP ONELAPSED TIME H0To minimize any vertical bars orstripes visible on the screenbackground.The horizontal screensize will also change.To adjust the focus of the display.This item allows you to remove anyhorizontal noise and clear or sharpenthe image of characters.Used to adjust the volumeUsed to adjust the trebleUsed to adjust the bassUsed to adjust the balanceVOLUMETREBLEBASSBALANCETo choose the language in which thecontrol names are displayed.To adjust position of the OSD windowon the screen.To select beep ON or OFF.To display the use time of monitorLANGUAGEOSD POSITIONBEEPELAPSED TIMECLOCKPHASE
A9Video Memory ModesThe monitor has 30 memory locations for display modes, 14 of which arefactory preset to popular video modes.Display Modes (Resolution)User ModesModes 15-30 are empty and can accept new video data. If the monitor detects anew video mode that has not been present before or is not one of the presetmodes, it stores the new mode automatically in one of the empty modes startingwith mode 15.If you use up the 16 blank modes and still have more new video modes, themonitor replaces the information in the user modes starting with mode 15.1234567891011121314640 x 350720 x 400640 x 480640 x 480640 x 480640 x 480800 x 600800 x 600800 x 600800 x 600832 x 6241024 x 7681024 x 7681024 x 76831.4731.4731.4735.0037.8637.5035.1637.8848.0846.8849.7248.3656.4860.027070606773755660727575607075Display Modes (Resolution) Horizontal Freq.(kHz) Vertical Freq.(Hz)VGAVGAVGAMACVESAVESAVESAVESAVESAVESAMACVESAVESAVESANote : This LCD monitor has been pre-adjusted to the video mode of VESA 1024x768 @75Hz.
A10TroubleshootingCheck the following before calling for service.Display Position is incorrect.Push the AUTO/SET Button.If the results are unsatisfactory, adjust the image position using the H positionand V position icon in the on screen display.On the screen background, vertical bars or stripes are visible.Push the AUTO/SET Button.If the results are unsatisfactory, decrease the vertical bars or stripes using theCLOCK icon in the on screen display.Any horizontal noise appearing in any image or characters arenot clearly portraid.Push the AUTO/SET Button.If the results are unsatisfactory, decrease the horizontal bars using the PHASEicon in the on screen display.NO SIGNAL message.The signal cable is not connected, or is loose. Check and secure theconnection.OUT OF RANGE message appears.Picture is blank.The frequency of the signal from the video card is outside the operating rangeof the monitor.Horizontal Frequency: 31kHz-61kHzVertical Frequency: 56Hz-75Hz*Use the graphics board's utility software to change the frequency setting (Refer to themanual for graphics board).*You can change the setup to the supported resolution using the Safe Mode (Press theF8 key during booting the system).The power LED is illuminated amber.The monitor is in its display power management mode.There is no active signal coming from the PC.The signal cable is not fastened securely.Check the computer power and graphics adapter configuration.The monitor doesn't enter the power saving off mode (Amber).Computer video signal is not VESA DPMS standard. Either the PC or the videocontroller card is not using the VESA DPMS power management function.
A11SpecificationsType15inch (38.1cm) Flat Panel Active matrix-TFT LCDAnti-Glare coatingViewable Size 15inch (38.1cm) Pixel pitch 0.297 x 0.297mmTrue color 16 million colorHorizontal Freq. 31kHz - 61kHz (Automatic)Vertical Freq. 56Hz - 75Hz (Automatic)Input form Separate, TTL, Positive/NegativeSignal input 15 pin D-Sub connectorDisplay Area 304 x 228mm / 12.0 x 9.0inchInput FormSeparate, RGB Analog, 0.714Vp-p/75ohm,PositiveResolution (max.) VESA 1024 x 768 @ 75HzRMS Audio Output 2W(R + L)Input Sensitivity 0.7VrmsSpeaker Impedance 4ΩNormal(Max.) ≤36WStand-by/Suspend ≤3WPower Off ≤3WWidth 389.2 cm / 15.3 inchesHeight 382.4 cm / 15 inchesDepth 16.18 cm / 6.37 inches DC 12V 3AInput AC 100-240V, 50 - 60Hz, 1.2A - 0.6AOutput DC 12V 3ANet 4.8 kg / 10.6 lbsDown 5˚Up 30˚Operating conditionTemperature 10˚C to 35˚CHumidity 10% to 80% non-condensingStorage conditionTemperature -20˚C to 60˚CHumidity 5% to 95% non-condensingNOTEInformation in this document is subject to change without notice.DisplaySync InputVideo InputAudioPowerConsumptionDimensionsPower InputAC AdapterWeight Tilt RangeEnvironmentConditions-+

Navigation menu