LG Electronics USA LST2500 PCS CDMA WLL Terminal User Manual LST2500 User Manual

LG Electronics USA PCS CDMA WLL Terminal LST2500 User Manual

Users Manual

LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A2CDMA Fixed Wireless TerminalUser GuideModel: LST- 2500(F)/LST-2500A
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A3REVISED HISTORYDATE ISSUE CONTENTS OF CHANGES REMARK2001.03.05ISSUE 1.0 Initial ReleasePlease read this manual before you use this product. This manual is based on the productionversion of LST2500(F)/LST2500A(F) FWT. Software changes may have occurred after thisprinting.LG reserves the right to make changes in technical and product specifications withoutprior notice.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A4Blank Page
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A5Table of Contents1. Before You Start....................................................................................................71.1 Safety Information....................................................................................................................71.2 Optimal Phone Performance ...................................................................................................71.3 Care and Service .....................................................................................................................82. Introduction...........................................................................................................92.1 Front View of the Terminal ..................................................................................................... 112.2 3 LEDs Indicators................................................................................................................... 112.3 Installation ............................................................................................................................. 11STEP I. Check Components ............................................................................................... 11STEP II. Place the Terminal ................................................................................................12STEP III. Connect Components ..........................................................................................12STEP IV. Check LED indicators ..........................................................................................12STEP V. Install of Wall Mounting.........................................................................................122.4 Installation Steps....................................................................................................................133. Basic Operation ..................................................................................................143.1 Power On...............................................................................................................................143.2 Placing a call..........................................................................................................................143.3 Receiving a call......................................................................................................................143.4 Ending a call ..........................................................................................................................143.5 Warning Tone after Remote Disconnect................................................................................143.6 Dial Delay(Enblock mode only)..............................................................................................153.7 Emergency Call(Enblock mode only).....................................................................................154. System Features.................................................................................................164.1 Hook flash..............................................................................................................................164.2 Dial Delay Time(Enblock mode only).....................................................................................164.3 ROH (Receiver Off Hook)......................................................................................................164.4 Special Cellular Services .......................................................................................................164.5 Applications............................................................................................................................175. Programming ......................................................................................................185.1 Speed Dial(Enblock mode only) ............................................................................................18Storing the Speed Dial Number.............................................................................................18Enable or Disable Speed Dial................................................................................................18Operation ...............................................................................................................................195.2 Emergency Call(Enblock mode only).....................................................................................19Entering the emergency phone number ................................................................................19Enable or Disable emergency call .........................................................................................195.3 Hot Line(Enblock mode only).................................................................................................19Programming the Hot Line number........................................................................................19Enable the Hot Line Feature..................................................................................................19Disable the Hot Line Feature.................................................................................................20Programming the Hot Line Time............................................................................................205.4 Alarm(Enblock mode only).....................................................................................................20Entering Alarm Time (12-hour Mode) ....................................................................................20Entering Alarm Time (24-hour Mode) ....................................................................................20Disable Alarm Feature ...........................................................................................................205.5 Volume Level .........................................................................................................................21Changing the Volume Level...................................................................................................215.6 Outgoing Call Lock(Enblock mode only) ...............................................................................21Enable or Disable Outgoing Call Lock...................................................................................21Changing Outgoing LOCK Code ...........................................................................................215.7 G3 FAX Mode Setting ............................................................................................................22Enable or Disable G3 FAX mode...........................................................................................22
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A66. Troubleshooting ..................................................................................................247. General Information ............................................................................................257.1 LST-2500(F)/LST-2500A(F)...................................................................................................25
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A711.. BBeeffoorree YYoouu SSttaarrtt1.1 Safety Information WarningTo reduce the risk of fire or electric shock, do not expose this product to rain or moisture.Do not use this product near swimming pools or other bodies of water.IMPORTANT Before installing or operating this product, read this information..1.2 Optimal Phone Performancel Do not operate your product when holding the antenna, or when someone is within fourinches (ten centimeters) of the antenna. Holding the antenna affects call quality and maycause the telephone to operate at a higher power level than needed.l For the best call quality, keep the antenna free from obstructions and point the antennastraight up.l Do not use the unit with a damaged antenna. Have your antenna replaced by a qualifiedtechnician immediately. Use only a manufacturer-approved antenna. Non-approvedantennas, modifications, or attachments could impair call quality, damage the phone.l RF energy may affect improperly installed or inadequately shielded personal medicaldevices such as pace markers, hospital monitor. Consult the manufacturer of any personalmedical devices to determine if they are adequately shielded from external RF energy.Turn your terminal OFF in health care facilities when any regulations posted in the areasinstruct you to do so. Hospitals or health care facilities may be using equipment that couldbe sensitive to external RF energy.l If this equipment does cause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the radio or television and the telephone. -Connect the equipment into an outlet on a circuit different from that to which theterminal is connected. -Consult you Authorized LG Dealer of an experienced radio/TV technician for help.l Use only the battery, antenna and AC power supply provided by LG. Using any other typewill invalidate the warranty.l Only authorized personnel should service the phone and its accessories. Faultyinstallation or service any be dangerous and may invalidate the warranty.l Do not use the unit in designated “no cellular phone use” area.l Avoid exposure to high temperature or humidity.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A8l Avoid wetting the unit with any liquids. If the unit gets wet, turn the power off immediatelyand remove the backup battery and AC power supply. If the unit is inoperable, then returnto the service agent for service.l Avoid shock or impact.l We recommend you to charge the backup battery before initial use. Backup battery maybe discharged during delivery.l This device complies with part 15 of the FCC Rules.Operation is subject to the following two conditions:-This device may not cause harmful interference, and-this device must accept any interference received, including interference that maycause undesired operation.1.3 Care and Servicel Unplug the Telephone from the wall outlet and remove antenna (or disconnect antennacable) before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth forcleaning.l If the unit fails for any reason, do not attempt to disassemble; contact the telephoneservice provider for assistance.l If any of the following conditions exist: Unplug the unit at the wall plug, remove battery,and call the service provider. -The power supply cord is damaged or frayed. -Liquid has been spilled into the unit. -The unit has been exposed to rain or water. -The unit has been dropped or damaged. - The unit does not work normally by following the operating instructions.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A922.. IInnttrroodduuccttiioonnCongratulations on your purchase of the LG Fixed Wireless Terminal that has been designed tooperate on the latest digital mobile communications technology, Code Division Multiple Access(CDMA). This CDMA digital technology has greatly enhanced voice clarity and can providevarious advanced features. The terminal enables the normal operation and direct connection ofstandard telephone equipment into the cellular network.The standard unit provides:l Dial tone;l Touch tone (DTMF) or Pulse Dialing;l Support Caller ID Telephone;l Voice-Mail Notification ring-alerts you to new voice-mail messages;l Ring voltage used to ring the telephone connected to the unit, with a Ringer EquivalenceNumber of 4;l A phone jack to plug in the telephone equipment (RJ-11 Port);l A phone jack to plug in the G3 FAX equipment (RJ-11 Port);l RJ45 Data Port for service and repairl AC Power supply with barrel plug connector;l Three lights (LEDs) to indicate the status of the unit;l Dipole Antenna;The LG Fixed Wireless Terminal can operate differently according to the system providerin the dialing manner. The first one is the “Enblock” mode and the second one is the“Overlap” mode. Please contact your service provider in which mode the LG FixedWireless Terminal is working.Some features can not be supported by service provider’s policy and dialing method.For instance, the following features may not be supported in Overlap dialing mode;- Dial Delay and Dial Delay Time- Speed Dial- Emergency Call- Hot Line Call- Alarm- Outgoing Call LockOther features as determined by your service provider.Note: Telephones with multiple terminating impedance should be set for 600ohms.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A102.1 Front View of the Terminal< Figure 1 >ITEM DESCRIPTION① LEDs Indicate the status of the unit② DC-12V AC Power Adapter③ FAX (RJ-11 Jack) Connecting Port for G3 FAX Machine④ Phone (RJ-11 Jack) Connecting Port for Single Line Telephone⑤ RJ45 Connector Connecting Port for Data Service to PC⑥ TNC Antenna Connector Connecting Port for TNC Antenna
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A112.2 3 LEDs IndicatorsLED COLOR Operating ConditionGREEN-solid DC Power is appliedORANGE-solid Battery Power is appliedPOWER LEDRED-solid Low BatteryGREEN-solid Good SignalORANGE-solid Poor SignalSIGNAL LEDRED-solid No Service AreaGREEN – blink(0.5sec On / 0.5sec Off) Voice Message is receivedGREEN – blink(1 sec On / 1 sec Off) Data Service or G3 Fax Service is workingMODE LEDGREEN-solid G3 FAX receive mode is enabled2.3 InstallationYou should follow each step carefully as shown below in order to guarantee proper operation ofCDMA Fixed Wireless Telephone.STEP I. Check Componentsl Fixed Wireless Terminal is supplied with the following standard unit and accessories;1. LST-2500(F)/LST2500A(F) Main Unit -1 EA-2. Dipole Antenna -1 EA-3. Backup Battery -1 EA-4. User Guide .-1 EA-5. AC/DC Power Adapter -1 EA-6. Power Cord -1 EA-l Please make sure that these components are present and check for evidence of shippingbefore you begin the unit installation. If components are missing or damage is found,contact your authorized LG distributor immediately.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A12 STEP II. Place the Terminall Place the terminal on the stable flat secure surface area (desk, table, etc.). Avoid directexposure to the sun lights and damp area.l Read the Safety Information located at the first part of this document before you place theterminal. STEP III. Connect Componentsl Connect the antenna to the TNC connector located at the topside of the terminal. (SeeFigure 1 to locate the TNC connector.) If you placed the terminal on the flat surface, bendthe antenna up right.l Connect your phone cord to the RJ-11C port located at the left side of the terminal.l Connect the battery cable to the DC battery connector at the back of the main unit. -. Remove the battery compartment cover. -. Connect battery to the connector. -. Replace the battery cover.l Connect the AC power supply cable to the DC input port located at the right side of theterminal.l If you use Data Service or PC FAX Service, connect your RJ45 cable cord to the RJ45 portlocated at the right side of the terminal.l If you use G3 FAX machine, connect your line cord of G3 FAX to the RJ-11 port located atthe right side of the phone port. “ Refer to Connection Diagram with external equipment in Figure 2 “ STEP IV. Check LED indicatorsl When you followed the installation instruction STEP I to STEP III, please check the LEDs fornormal operation. When DC power is fed at the first time, LEDs will operate asfollows:1. After few seconds, if receiving signal strength is strong enough, then SIGNAL LED isGREEN, if not, it is ORANGE or RED. And MODE LED is turned off. Power LED isGREEN if AC/DC power is applied. STEP V. Install of Wall Mountingl To mount terminal on the wall, please follow the procedure to install it correctly.1. Determine suitable location to mount terminal with mounting template;2. Mark the two openings and select round or panhead type screw;3. Drill out the holes with drill bit smaller in diameter than the screws4. Secure two screws into the wall, leaving about 1/8inch gap between the screw headsand the wall;5. Insert the DC power pack into an electrical outlet and attach the telephone line into thePhone Jack (RJ-11) of the unit.6. Place the terminal over the two screws so that the screw head protrudes out of the opening;7. Slide the terminal downward until the screw head is locked at the top of the opening andthe terminal is secure;8. Tighten the screws the terminal is resting upon;
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A13RJ-45 [LST-2500(F)/LST-2500A(F)]* Note :- G3 Fax can not connected to your LST-2500/LST-2500A terminal.- Length between LST-2500(F)/LST-2500A(F) and Telephone : over 1m.※ The adapter type(with power cord) may be different by country adaptation.< Figure 2. Connection Diagram with External Equipment >2.4 Installation StepsPlease follow the below procedure to install the unit properly.Connect theantenna to theTNC connector(Turn right).Bend theantenna up right.Connect your phoneCord.Connect the ACpower supply.213TELEPHONEG3 Analog FaxPCRJ-11RJ-11
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A1433.. BBaassiicc OOppeerraattiioonn3.1 Power On1. The POWER LED indicates the presents status;1) Using AC Adapter : Solid Green2) Using internal battery : Solid ORANGE3) Using internal battery and battery is week : Solid Red2. If the radio service is not available or radio signal is too weak to detect; The SIGNAL LED is Red. (No Service status) 3. When the phone is succeeded in getting the service, SIGNAL LED indicates the strengthof the signal.1) Lifting handset, dial tone is heard and you can enter a phone number. (Not entering any key for 15 seconds (In the overlap dial mode, it may take over 15seconds.) warning tone will be produced)*) If Hot Line function is enabled, busy tone is not produced and hot line number isautomatically connected.*) While having maintenance request order or lock order from the main system, neither dialtone nor busy tone is produced. Instead of them, the lock tone(“pi-pi-pi”) will be heardone time and there will be no sound and both of MODE LED and POWER LED will beblinking with GREEN color simultaneously.3.2 Placing a callWhen lifting handset of the connected phone ("off hook"), the terminal determines whethercellular service is available. If it is available, dial tone is produced and a number can be dialednormally. If phone service is not available, SIGNAL LED of the terminal will be red and no dialtone will be heard.3.3 Receiving a callThe connected telephone rings when an incoming call is detected. Pick up the handset andbegin talking.3.4 Ending a callWhen you have completed the call, place the handset back on hook. Also you can hook flashmore than about 1 second to end a call and place a new call without hanging up the handset.3.5 Warning Tone after Remote DisconnectA warning tone may be heard in the telephone after a remote party hangs up from a call,allowing another call to be initiated after hook-flash.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A153.6 Dial Delay(Enblock mode only)The terminal waits 5 seconds before transmitting the dialed telephone number into the cellularnetwork.3.7 Emergency Call(Enblock mode only)When emergency call number is connected once, it will not be terminated unless the called partydisconnects the call(Emergency Call Hold Service). Therefore even caller hangs up the phone,the line will be still connected, so if the caller picks up the phone again, he can continue talking.If emergency call is connected, cellular service is not supported.As long as your telephone is registered on a system, you can place a call to emergency numberincluding 911-even if your telephone is locked* or restricted*.Please check the available emergency call number with your service provider.*) “Transmit Lock” or “Transmit Restrict” features have a meaning only in “Enblock” mode.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A1644.. SSyysstteemm FFeeaattuurreess4.1 Hook flashWhen the terminal receives a hook-flash from the connected telephone device, it willautomatically allow:1. For producing dial tone again after a phone number has been dialed without connection.2. The use of special cellular services which may be available in your cellular service area.Note: Hook-flash is accomplished in a call through either pressing the dedicated hook-flashkey which is available on some phones or through a rapid single press of the hang-upmechanism upon which the handset rests when the phone is hung up.4.2 Dial Delay Time(Enblock mode only)When placing a call, the phone number is sent over the network after last digit is dialed. In orderto insure adequate time for dialing the last digit, a delay of 5 seconds is programmed into theterminal.4.3 ROH (Receiver Off Hook)If the telephone equipment remains “off-hook”, meaning that the handset is left off of its cradle asit would be when you hang up, with no dialing activity for about 45 seconds, a ROH tone emitsfrom the receiver for a period of 60 seconds.(In the overlap dial mode, above “45 seconds” or“60 seconds” may be different according to the system.)( This feature may be available or not by country specification.)4.4 Special Cellular ServicesMany cellular systems offer special services such as call waiting, call forwarding, etc. You canpurchase these services from your cellular service provider. There are certain dialing sequencesto be entered, which vary from service provider to service provider. The service provider willprovide the dialing instructions for your system.Call Forwarding – An incoming call can be delivered to another telephone number programmed.Please contact your cellular service provider to use this feature.Call Waiting – You can receive another incoming call during a call. In this case, you will hearbeep tone and then you can connect the second call holding the first call by entering a coderequired by cellular service provider. Your cellular service provider may require hook-flash (aquick, simulated "hang up") to answer the waiting call. Other providers may require entering thecodes involving digits 1-9, *, and # to answer a waiting call.Three-way Conference Calls - For three-way conference calls, a hook-flash transmits theSEND command. Please contact your cellular service provider for more information on using thisservice.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A17F Example① Dial the first number and wait until connected;② When connected, give hook-flash and dial the second number and give one more hook-flash to beconnected;③ When the second call is connected, give hook flash to complete a 3-way conference call.Voice Mail – Use voice mail service in the same manner as you would on a regular telephone. Ifyou have a new voice-mail message, the WLL-terminal transmits a special Voice-MailNotification Ring (1sec On / 6sec Off default) and Mode LED is blinking (0.5sec On/0.5sec Off).Please contact your cellular service provider for more information on using Voice Mail or tochange Voice-Mail Ring pattern.Caller ID – LST-2500(F) can support Caller ID service if you have a telephone with Caller IDfeature. Please contact your cellular service provider for more information on using this service.4.5 ApplicationsData Communication - LST-2500(F) is capable of transmitting and receiving IS-707 Fax ormodem communications. For data communications, you will need a data communication kit anda PC Fax software diskette where needed. For further information, please contact our authorizedservice dealer.Multi-extension Installations - For a multi-extension installation, make sure that all theextensions are on-hook. If one extension is off-hook (not hung up), none of the extensions onthat line will ring when a call is being received.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A1855.. PPrrooggrraammmmiinnggLST-2500(F) provides various convenient and various features to user. This chapter describeshow to program these features and to use them. The followings are main features can be used;Speed Dial(Enblock mode only)Emergency Call(Enblock mode only)Hot Line Call(Enblock mode only)Wake-up Alarm(Enblock mode only)Conversation Voice LevelOutgoing Call Lock(Enblock mode only)n Programming Instruction1. Lift Handset and press “#” key twice.2. Enter the field number (1 ~ 6) and you will hear the Menu Entering tone.3. Press “#” key and you will hear confirmation tone.4. Enter sub-fields and their options.5. Press “*” key to save and you will hear confirmation tone.5.1 Speed Dial(Enblock mode only)LST-2500(F) has 30 memory locations (1~30:1 or 2 digits) to store frequently used phonenumbers and you can make a call by pressing memory location number only when the speeddial feature is enabled.Storing the Speed Dial Number1. Press “#” + “#” + “1” continuously to enter speed dial programming mode.2. Press “#” and one of memory numbers (1~30).3. Press “#” and the phone number (Max. 32 digits).4. Press “*” to store.Enable or Disable Speed Dial1. Press “#” + “#” + “1” continuously to enter speed dial programming mode.2. Press “#” and “1” or “2” to enable or disable respectively. “1” – Speed Dial Enable “2” – Speed Dial Disable3. Press “*” to store.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A19Operation1. Make a speed dial function enable.2. Lift handset and dial tone will be heard.3. Press speed dial number and wait for dial timeout(5 seconds).5.2 Emergency Call(Enblock mode only)LST-250(F)/2500(F) has 3 emergency call numbers (1~3) and max. 32 digits can be stored ineach emergency call number.Entering the emergency phone number1. Press “#”+”#”+”2” continuously to enter emergency call programming mode.2. Press “#” and one of the emergency memory location numbers (1~3).3. Press “#” and the phone number (Max. 32 digits).4. Press “*” to save and enable this function.Enable or Disable emergency call1. Press “#”+”#”+”2” continuously to enter emergency call programming mode.2. Press “#” and Enable code (“1”) or Disable code (“2”).3. Press “*” to save.If Emergency Call is disabled and Emergency Call number has been already programmed,you can make enable Emergency Call by pressing “#’+”#”+”2”+”#” + ”1”+”*” withoutentering a emergency call number again.5.3 Hot Line(Enblock mode only)While the Hot line function is enabled, the programmed number will be automatically dialedwhen you pick up the handset and wait for the programmed hot line time (2~10sec) without anykey press.Programming the Hot Line number1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line Enable code “1”.3. Press “#” and Hot Line phone number (Max. 32 digits).4. Press “*” to save and enable this function.Enable the Hot Line Feature1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line Enable code “1”.3. Press “*” to save.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A20Disable the Hot Line Feature1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line Disable code “2”.3. Press “*” to save.Programming the Hot Line Time1. Press “#”+”#”+”3” continuously to enter Hot Line programming mode.2. Press “#” and Hot Line time code “3”.3. Press “#” and enter desired Hot Line time (2~10 seconds).4. Press “*” to save.If Hot Line is disabled and Hot Line number has been already programmed, you can makeenable Hot Line feature by pressing “#’+”#”+”3”+”#”+”1”+”*” without entering a Hot LineNumber again.5.4 Alarm(Enblock mode only)If alarm feature is enabled, you will hear ring at the programmed alarm time every day for 1minute.Entering Alarm Time (12-hour Mode)1. Press “#”+”#”+”4” continuously to enter alarm time programming mode.2. Press “#” and alarm time code “1” for 12-hour mode.3. Press “#” and alarm time (HHMM +am(“1”) / pm(“2”)).4. In the forenoon, time range is 0000~1159.5. In the afternoon, time range is 1200~1259 or 0100 ~1159.6. Press “*” to save and enable Alarm Time.Entering Alarm Time (24-hour Mode)1. Press “#”+”#”+”4” continuously to enter alarm time programming mode.2. Press “#” and alarm time code “2” for 24-hour mode.3. Press “#” and alarm time (HHMM). (0000~2359)4. Press “*” to save and enable Alarm Time.Disable Alarm Feature1. Press “#”+”#”+”4” continuously to enter alarm time programming mode.2. Press “#” and alarm disable code “2”.3. Press “*” to save.If Alarm is disabled and time has been already programmed, you can make enable Alarmfeature by pressing “#’+”#”+”4”+”#”+”1”+”*” without entering alarm time again.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A215.5 Volume LevelThere are three voice volume levels to be controlled by software, and you can set the level to theadequate conversation volume.Changing the Volume Level1. Press “#”+”#”+”5” continuously to enter Volume Level programming mode.2. Press “#” and Volume Level (1~3), then the confirm tone will be heard with the volumelevel changed. “1” – LOW Level “2” – MIDDLE Level “3” – HIGH Level3. Press “*” to save.Before pressing “*”, you can enter volume level continuously.5.6 Outgoing Call Lock(Enblock mode only)If you try to make an outgoing call while outgoing call lock is enabled, then you will hear warningtone after dial time-out as a indication of entering the LOCK code. You should enter LOCK codeto make an outgoing call. LOCK code is composed of 4 digits and the initial setting is “0000”.Outgoing Call Lock feature is disabled as a factory setting.Enable or Disable Outgoing Call Lock1. Press “#”+”#”+”6”+LOCK code continuously to enter Outgoing Call Lock programmingmode.2. Press “#” and Enable (“1”) or Disable (“2”) code.3. Press “*” to save.Changing Outgoing LOCK Code1. Press “#”+”#”+”6”+LOCK code continuously to enter Outgoing Call Lock programmingmode.2. Press “#” and “3” to change LOCK code.3. Press “#” and 4 digits of new LOCK code.4. Press “#” and re-enter new LOCK code.5. Press “*” to save.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A225.7 G3 FAX Mode SettingTo activate a Data Fax call by G3 FAX connected to your LST-2500(F)/LST-2500A(F) terminalfrom the other devices (Land or Mobile Data Fax), your service provider should support wirelessdata FAX. And the LST-2500(F)/LST-2500A(F) mode should be changed to G3 FAX mode tochange data path from RJ11 to G3 FAX machine. Because the terminal doesn’t recognize thecall is for FAX or voice before being response. Following is the procedure to change data pathand default data path is RJ45 data path.Once G3 Fax mode is set, if AC power is gone and turned on again, the saved G3 Fax modevalue is restored.Enable or Disable G3 FAX mode1. Press “#”+”#”+”7” continuously to enter G3 FAX programming mode.2. Press “#” and Enable (“1”) or Disable (“2”) code. Enable means that Data call path is changed to G3 FAX. Disable means that Data call path is changed to RJ45. (Default mode)3. Press “*” to save.Note 1. How to setup G3 FAX mode more easy1. Press “#”+”#”+”7” continuously to enter G3 FAX programming mode.2. Press Enable (“1”) or Disable (“2”) code. Enable means that Data call path is changed to G3 FAX. Disable means that Data call path is changed to RJ45. (Default mode)Note 2. Sending or receiving some documents by G3 FAX is possible only in AC power mode. IfAC power is gone, you can not use the G3 Fax machine connected to the LST-2500(F)/LST-2500A(F).Note 3. The recommended usage for this G3 Fax Mode is like this;1. Disable G3 Fax Mode for normal usage.- You can make a voice call using the telephone device connected to the “Tel/Fax”jack of the LST-2500(F)/LST-2500A(F).- You can fax a document using the G3 Fax machine connected to the “Tel/Fax”jack of LST-2500(F)/LST-2500A(F).2. To receive or send a document by fax, should be set G3 Fax Mode. After receivingthe fax document, disable G3 Fax Mode for another voice call.3. If you want to use the LST-2500(F)/LST-2500A(F)terminal only for G3 Fax sending orreceiving other than the voice call, then keep the terminal in G3 Fax Mode enabledstate.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A2366.. TTrroouubblleesshhoooottiinnggIn the event you are unable to place or receive telephone calls, first check the appropriate powerindication on the LED. In case of no power, check the wiring connections between the poweroutlet and the terminal. Check for the appropriate service indication on the LED. If an adequatesignal is not present, try different locations for the better signal reception.This will verify the condition of the telephone equipment and the internal wiring of the telephoneservice to verity that it is working properly. If the telephone system of wiring is not workingproperly, replace or repair the equipment as required. The unit will not function with equipmentthat requires data transmission.Contact your service provider if either of the following condition is true:l The terminal does not work and the LED indicates “No Service” and if changing thelocations does not resolve the problem.l The terminal does not work and the LED indicates “In Service”.l Power Supply – If the unit does not respond once plugged into a power supply;² Check that the AC power source.² Check that the Barrel Plug of the Power Supply is properly inserted into theterminal.² Check that the terminal Power Supply is properly plugged into the electrical outletor power source.Warning! Only Authorized Service Personnel should remove the cover of the fixedwireless terminal for additional service. The contents of the terminal contain componentsthat present an Electric Shock Hazard if handled improperly.For further assistance, contact your Authorized LG Distributor for service andassistance. Please keep your Model number and Serial number ready for quickerservice.
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A2477.. GGeenneerraall IInnffoorrmmaattiioonn7.1 LST-2500(F)/LST- (F)● Main UnitItem DescriptionTx Frequency Digital : 1850 ~ 1910 MHzRx Frequency Digital : 1930 ~ 1990 MHzChannel Bandwidth 1.25 MHzFrequency Stability Digital : ±150 HzTx Power Digital : Max. 0.2WRx Power Level -104 ~ -25 dBmSize 148 x 210 x 60 mmWeight(g) 710g ( w/o battery ) / 990g ( w/ battery )● AC/DC Adapter(A)Item DescriptionInput Voltage 110V ~ 250V ACInput Current 0.6ArmsInput Frequency 50 ~ 60 HzOutput Voltage 12V(DC) / 1.5A● AC/DC Adapter(B)Item DescriptionInput Voltage 110V ~ 250V ACInput Current 0.3AInput Frequency 50 ~ 60 HzOutput Voltage 12V(DC) / 2A● Internal Back-up BatteryItem DescriptionCapacity 8.4V NiMH
LG CDMA Fixed Wireless TerminalLST-2500(F)/LST-2500A25Talk duration time 2 HoursStandby duration time 24 HoursCharging duration time Trickle, 24 HoursLicensed by QUALCOMM Incorporated under one or more of the following Patents:U.S, Patent No. 4,901,307 U.S, Patent No. 5,056,109 U.S, Patent No. 5,099,204U.S, Patent No. 5,101,501 U.S, Patent No. 5,103,459 U.S, Patent No. 5,107,225

Navigation menu