LG Electronics USA LX295 Cellular/PCS CDMA Phone with Bluetooth User Manual User s Manual
LG Electronics USA Cellular/PCS CDMA Phone with Bluetooth User s Manual
Users Manual
User Manual LX295 -1- Part 15.21 statement " Change or Modifications that are not expressly approved by the manufacturer could void the user's authority to operate the equipment. “ Part 15.105 statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Part 15 Class B Compliance This device and its accessories comply with part15 of FCC rules. Operation is subject to the following two conditions: (1) This device & its accessories may not cause harmful interference. (2) This device & its accessories must accept any interference received, including interference that may cause undesired operation. Body-worn Operation This device has been tested for typical body-worn operations with the distance of 0.79inches (2.0cm) from the user’s body. To comply with FCC RF exposure requirements, a minimum separation distance of 0.79inches(2.0cm) must be maintained from the user's body. Additionally, Belt clips, holsters & other body-worn accessories may not contain metallic components. Getting Started Unlocking Your Phone If you received your LX295 in the mail, you may need to unlock it before making calls. 1. Press the END/PWR Switch for 2~3 seconds. 2. Press soft key Unlock. 3. Enter your four-digit lock code. For security purposes, the code will not be visible as you type. Note: If you can’t recall your lock code, try using the last four digits of your Social Security number, the last four digits of your Phone Number or 0000. View of Phone 1. END/PWR Switch: Lets you power the phone on or off. 2. Antenna: Retractable antenna provides optimum reception for 800 MHz & 1900 MHz frequencies. 3. Power On Indicator: Illuminates red when the phone powers on or when you receive incoming calls. Flashes red when you have messages of scheduled alarms. 4. Headset Jack: Provides connection for an optional headset. 5. Volume Control Keys: Adjust the Ring Volume in the Main Menu or the Voice Volume during a call. The keys also scroll through mouths in the Calendar or pages in the MiniBrowser. 6. Mouse Key: Allows quick and easy scrolling through the menus. 7. OK: Lets you place a call, receive a call, end a call or select menu options. 8. CLR: Lets you clear an entry or back-up in the menu. 9. Folder : Lets you answer or end calls. - 10 - Installing and Removing the Battery To install the battery, insert the bottom of the battery into the opening on the back of the phone. Then, push the battery down until the latch clicks. To remove the battery, press down on the latch and remove the battery from the phone. Turning Your Phone On and Off To turn your phone on, move the On/Off Switch (near the antenna) to the ON position. Your phone performs a short self-test before letting you know it is operational. If your phone does not turn on, make sure the battery is installed correctly and is adequately charged or has external power (via the AC Adapter, Cigarette Lighter Adapter or Hands-Free Car Kit). To turn your phone off, move the On/Off Switch to the OFF position. Main Menu When your phone acquires Service, the Greeting (a banner of text), the current time and date and the Main Menu are displayed. If you are in authorized analog cellular provider’s service area, you are ready to send and receive calls. Power Save Mode When the phone is in an area without service for 15 minutes, it stops searching for service and enters into the power Save Mode. When your phone activates this feature, Power Save is displayed on your screen. The phone automatically checks for service periodically or you can check manually by pressing any key. - 11 - Menu Navigation The Mouse Key lets you scroll circularly through menus quickly and easily. As you navigate through a menu, the options are highlighted (Highlighted Test Example ) . Select an option by highlighting it and pressing . The scroll bar at the right of the menu keeps track of your position in the menu at all times. For example, if you want to view your last incoming call: Incoming 1. From the Main Menu, select RECENT CALLS and press 2. (It may already be highlighted.) 2. Press the Mouse Key down to highlight and press If you have received any calls, they are displayed on the screen. Entering Characters Using the Keypad(T9) To enter a letter, punctuation or number when creating Phone Book or Scheduler entries, press the corresponding key until the desired character appears. By default, the first letter of a word is capitalized and following letters are lowercase. Characters in the following order: 1 . ? , ‘ &1 -@()/~ 7PQRS PQRS7pqrs ABC ABC2abc2 TUV8tuv8 3DEF 4G 5J 6MNO DEF3def3 8TUV 9WXYZ 0Space GHI4ghi4 JKL5jkl5 WXYZ9wxyz9 Next 0 Shift MNO6mno6 - 12 - Space After a character is entered, the cursor automatically advances to the next space after two seconds. You can also advance the cursor by pressing If you make a mistake, press or entering a character not on the same key. to move the cursor left or [CLR] to erase a character. To clear the entire entry, press and hold [CLR] for two seconds. - 13 - Display Icons Display icons are the symbols your phone uses to communicate important information. They are as follows: ICON DESCRIPTION 3G send 3G receive 3G send receive Alarm Battery Antenna In use No service Location Location out Voice Voice Privacy Vibrate Roaming TTY SSI Ringer Ringer off Text + voice - 14 - Antenna The antenna on your LX295 provides maximum reception by extending of retracting it. !!! WARNING – CHOKING HAZARD – ANTENNA MAY BECOME DISLODGED Attempting to remove or repeated twisting of the antenna will loosen the materials securing it into antenna. Once the antenna is loosened or removed, only an authorized service provider Representative can restore the antenna’s original integrity. Do not attempt to remove or twist the antenna. Signal Strength The quality of each call you make or receive depends on the signal strength on your area. The number of bars in the Signal Strength icon informs you of the current strength. The more bars, the stronger the signal. Battery Capacity Your LX295 is equipped with a Lithium Polymer battery. It allows you to recharge your battery before it is fully drained. The battery provides approximately 180 minuets of continuous digital talk time or approximately 110 hours of continuous digital standby time. Note: Long backlight settings affect the battery’s talk and standby times.3.25 When the battery reaches 5% of its capacity, the battery icon blinks. When there is about one minute of talk time left, the phone sounds an audible alert every 30 seconds and then powers down. If the battery’s charge is completely run down, it takes 2 to 3 hours to fully recharge. It is not necessary to let the battery completely run down before recharging. To charge your batteries, use only approved charging accessories. - 15 - Using the AC Adapter To charge the battery, plug the AC Adapter into a standard wall outlet and connect it to the phone via the I/O Connector on the bottom of the phone. Alternatively, you can place the phone in the charging cradle provided with your phone and connect the AC Adapter to the back of the cradle. The battery Charge Status icon flashes during charging. When the battery is fully charged, the battery icon stops flashing. Using Your Phone Placing a Call When the phone is turned on, check the Signal Strength icon to see of you are in a Service Area or authorized PCS CDMA provider’s service area. 1. Open the Flip. 2. Enter the phone number and press [SEND]. ☞Tip! When dialing long distance, it is not necessary to dial a “1” before the area code. 3. When you are finished with your call and press [END]. If the phone is in Active Flip Mode, closing the Flip will also end the call. Roaming With Your Phone Your Phone is you can use it to make and receive calls in many places. Setting Your Phone’s Mode Your Phone allows you to control your ability to roam. (See “Set Mode”) - 16 - Calling Experience When you use your phone on other PCS CDMA networks, your calling experience and call quality will be quite similar to what you experience when making calls within the Network. Although certain calling features may not be available, your phone calls are still private and secure. Correcting Dialing Mistakes To delete one digit at a time, press . To delete all digits, press and hole Redialing Last Outgoing Number Press and hold [SEND] for 2 seconds. Dialing Options (phone book – Not Functioning) When you enter numbers in the Main Menu, dialing options are displayed. To display a Phone Book entry, enter its entry number. To use the 4- Digit Dial option, enter the last four digits of a phone number in your Phone Book. To select an option, highlight it and press [SEND] .(Menu display only, phone book – Not Functioning) Call – Dials the phone number. Roam Confirm – Reminds you that you are making a call on an. (See “Disabling Roam Confirm” ) Roam Call – Dials the phone number using the current PCS CDMA or analog cellular network. Save – Saves the phone number in your Phone Book. (See “Saving a Phone Number” on the following page.) Find – Displays phone numbers in your Phone Book that contain the entered numbers. (See “Finding a Phone Number” ) Hard Pause – Inserts a Hard Pause. (See “Dialing and Saving Phone Numbers With Pauses” ) - 17 - z 2- Second pause – Inserts a two-second pause. (See “ Dialing and Saving Phone Numbers With Pauses” ) Exit – Returns to the Main Menu. A Phone Book Entry – Displays the Phone Book entry. To dial the entry’s speed-dealing number, press and hold [SEND]. To dial an alternate number, highlight it and press and hold [SEND]. ☞Tip! To speed dial a Phone Book entry from the Main Menu, press and hold the entry’s number. If the entry number is two digits, enter the first digit, then press and hole the second digit. (This feature will not work when the Roam Confirm option is enabled.) 4-Digit Dial – Dials the phone number in your Phone Book that ends with the four digits you enter. (See “4-digit Dialing” ) In Call Options During a call, your phone displays menu options in addition to the Main Menu. To select an option, Highlight it and press [OK].( functions ‘Send’ and ‘End’ only) End Call - Ends the call Send Tones - Sends the next set of numbers after a Hard Pause. (See “Dialing and Saving Phone Numbers With Pauses “ on the previous page.) Mute or Unmute – Select Mute to mute your phone’s microphone. Select Unmute to reactivate the microphone. Dial 3-Way Call – Lets you dial another phone number. Flash – Answers an incoming Call Waiting call or connects the third party for Three-Way Calling. - 18 - Incoming Call Notification Depending on your settings, your phone notifies you of incoming calls in the following ways: The phone rings or vibrates The LED flashes green The backlight illuminates The screen displays an incoming call message The phone number of the caller is displayed of the phone number is available The caller’s name is displayed if the phone number is in your Phone Book The following options are also displayed. To select an option, highlight it and press [SEND]. Answer – answers the call. Silent Ringer – Mutes the ringer. Note: You can also mute the ringer by pressing the up or down Volume Control key or [CLR]. Answering Calls To answer incoming calls, open the Flip (in Active Flip Mode) or press [SEND]. Note: If you open the Flip (in Active Flip Mode) and then press [SEND], you will hang up on the caller. To answer incoming roam calls, highlight Answer and press [SEND]. - 19 - Displaying Your Phone Number(phone book – not functioning) To display your phone number: 1. From the Main Menu, select SETTING & TOOLS. 2. And press 4 – 2 – 1. (System – Device Info – My Phone Number) Setting the Ring Volume to Vibrate To set the phone to Vibrate Mode, press the down Volume Control key until Ring Volume Vibrate is displayed. The phone will vibrate and – Vibrate On- is displayed above the Main Menu. To set the phone to Vibrate Mode using the Main Menu, see “Adjusting the Volume” . - 20 - Getting the Most From Service Retrieving Page/Text Messages To retrieve page/text messages: 1. From the Messaging 2. Highlight Inbox and press [OK]. Highlight the message you want to display and press [OK]. To select an option, highlight it and press [OK]. Text Message options: Forward Save Quick-Text. Add To Contacts Lock Message Info. Erasing All Page/Text Messages 1. From the Messages Menu, Press the Options Menu 2. Highlight Erase All and press [OK]. 3. Highlight Yes and press [OK]. Page/Text Message Storage Your LX295 can store up to 50 page/text messages. When the message memory is 100% full, a warning - 21 - message prompts you to erase messages to obtain more memory space. Roaming on to Other Service Providers Roaming occurs when you are in an area serviced by another authorized service provider. When this situation occurs, the R icon and Digital Roam of Analog Roam are displayed. If there is no service available, the ☎ icon is displayed. (Call History- not functioning) Page/Text Messages For information on page/text messages, see “Retrieving Page/Text Messages” . Sounds Adjusting the Volume 1. From the Main Menu, highlight Sounds and press [OK]. 2. Highlight Volume and press [OK]. 3. Highlight Ringer or Key Beep and press [OK]. ☞Tip! You can use the Volume Control keys to adjust the Ring Volume in the Main Menu or the Voice Volume during a call. 4. Highlight High, Medium, Low, Off or Vibrate (for Ringer only) and press [OK]. Note: When the phone is in Vibrate Mode and attached to and accessory (Desktop Charger, Hands- - 22 - Free Car Kit, etc.), it uses the Standard Ring Type to alert you of incoming calls, alarms or messages. Selecting Ring Types for Voice Calls To Select a Ring Type for Voice Calls: 1. From the Main Menu, highlight Sounds and press [OK]. 2. Highlight Ring Type and press [OK]. 3. Highlight Voice Calls and press [OK]. 4. Highlight With Caller ID, No Caller ID or Roaming and press [OK]. Note: If you select Roaming, the Ring Type is used for all incoming roaming calls. 5. Highlight a Ring Type and press [OK]. You will hear a preview of the Ring Type when you highlight it. ☞Tip! You can also assign different Ring Types to individual Phone Book entries. (See “Selecting an ID Finger” on page 46.) Selecting Ring Types for Messages To select a Ring Type for Messages: 1. From the Main Menu, highlight Sounds and press [OK]. 2. Highlight Ring Type and press [OK]. 3. Highlight Messages and press [OK]. 4. Highlight Voicemail, Page/Text of MiniBrowser and press [OK]. 5. Highlight a Ring Type and press [OK]. You will hear a preview of the Ring Type when you highlight it. - 23 - Tone Length Longer tone lengths may be better for tone recognition when dialing voicemail or other automated systems. To select a tone length: 1. From the Main Menu, highlight Sounds and press [OK]. 2. Highlight Tone Length and press [OK]. 3. Highlight Short of Long and press [OK]. Alert Notification To enable of disable alert sounds: 1. From the Main Menu, highlight Sounds and press [OK]. 2. Highlight Alerts and press [OK]. 3. Select an alert by highlighting it and pressing [OK]. Services – An alert sounds when you exit or enter PCS CDMA or cellular coverage. Messages – An alert sounds when you receive a voicemail or page/text message. Minute Minder – Your phone beeps once a minute when you are on a call. (The beep is not audible to the other party.) 4. Highlight ON or Off and press [OK]. Display For information on changing Backlight, Greeting or Contrast settings, see Handy Tips. - 24 - Display Menu Security Accessing the Security Menu You must enter your lock code to view the Security menu. If you forget your lock code, try using the last four digits of your Social Security number, the last four digits of your Phone Number or 0000. Security Menu To access the Security menu: 1. From the Main Menu, select SETTING & TOOLS and press 4 – 2 (System – Security). 2. Enter your lock code. Locking Your Phone When your phone is locked, you can only make calls to 911, Customer Care and Special Numbers or receive incoming calls. To lock your phone: 1. From the Security menu, highlight Lock Phone and press [OK]. 2. Highlight Lock Now or On Power up and press [OK]. If you select On Power Up, the phone will be locked each time it power up. Unlocking Your Phone 1. Highlight Unlock and press [OK]. 2. Enter your lock code. - 25 - Changing the Lock Code To change your lock code: 1. From the Security menu, highlight Change Lock and press [OK]. 2. Enter your new lock code. 3. Reenter your new lock code. Answering Your Phone with the Hands-Free Car Kit You can select different answering options when your phone is connected to the Hands-Free Car Kit. To answer calls automatically or by pressing any key: 1. From the Main Menu, highlight Setup and press [OK]. 2. Highlight Car Use and press [OK]. To select and option, highlight it and press [OK]. Any Key Answer - You can answer calls by pressing any key (not including the [CLR] key, Mouse Key or Volume Control keys). Auto Answer - Your phone answers incoming calls automatically after five seconds. 3. Highlight On and press [OK]. To disable an option, follow steps 1 and 2 and select Off. - 26 - Using Your Phone With a Hearing Aid Device A number of Sprint phones have been tested for hearing aid device compatibility. When some wireless phones are used with certain hearing devices (including hearing aids and cochlear implants), users may detect a noise which can interfere with the effectiveness of the hearing device. Some hearing devices are more immune than others to this interference noise, and phones also vary in the amount of interference noise they may generate. ANSI standard C63.19 was developed to provide a standardized means of measuring both wireless phone and hearing devices to determine usability rating categories for both. Ratings have been developed for mobile phones to assist hearing device users find phones that may be compatible with their hearing device. Not all phones have been rated for compatibility with hearing devices. Phones that have been rated have a label located on the box. Your LX295 has an M4 and a T4 rating. These ratings are not guarantees. Results will vary depending on the user’s hearing device and individual type and degree of hearing loss. If a hearing device is particularly vulnerable to interference noise; even a phone with a higher rating may still cause unacceptable noise levels in the hearing device. Trying out the phone with your hearing device is the best way to evaluate it for your personal needs. M-Ratings: Phones rated M3 or M4 meet FCC requirements for hearing aid compatibility and are likely to generate less interference to hearing devices than unrated phones. (M4 is the better/higher of the two ratings.) T-Ratings: Phones rated T3 or T4 meet FCC requirements and are likely to be more usable with a hearing device’s telecoil (“T Switch”or “Telephone Switch”) than unrated phones. (T4 is the better/higher of the two ratings. Note that not all hearing devices have telecoils in them.) Hearing aid devices may also be measured for immunity to interference noise from wireless phones and should have ratings similar to phones. Ask your hearing healthcare professional for the rating of your hearing aid. Add the rating of your hearing aid and your phone to determine probable usability: 䢇 Any combined rating equal to or greater than six offers excellent use. 䢇 Any combined rating equal to five is considered normal use. 䢇 Any combined rating equal to four is considered usable. Thus, if you pair an M3 hearing aid with an M3 phone, you will have a combined rating of six for “excellent use.”This is synonymous for T ratings. SprintNextel further suggests you experiment with multiple phones (even those not labeled M3/T3 or M4/T4) while in the store to find the one that works best with your hearing aid device. Should you experience interference or find the quality of service unsatisfactory after purchasing your phone, promptly return it to the store within 30 days of purchase. With the Sprint 30-day Risk-Free Guarantee, you may return the phone within 30 days of purchase for a full refund. More information about hearing aid compatibility may be found at: www.fcc.gov, www.fda.gov, and www.accesswireless.org. Getting the Best Hearing Device Experience With Your Phone To further minimize interference: 䢇 Set the phone’s Display and Keypad backlight settings to ensure the minimum time interval: 1. Press Menu > Settings > Display > Backlight > Main LCD, Key, or Sub LCD. 2. Select the minimum time interval setting and press OK. 䢇 Position the phone so the internal antenna is farthest from your hearing aid. 䢇 Move the phone around to find the point with least interference.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Encryption : Standard V2.3 (128-bit) User Access : Print, Print high-res Tagged PDF : No XMP Toolkit : 3.1-702 About : uuid:53d9aaf6-5bd7-4561-b0b6-79e91734fdef Producer : Acrobat Distiller 8.1.0 (Windows) Company : 엘지전자(주) Source Modified : D:20090120013100 Creator Tool : Word용 Acrobat PDFMaker 8.1 Modify Date : 2009:03:27 12:05:42-04:00 Create Date : 2009:01:20 01:35:16Z Metadata Date : 2009:03:27 12:05:42-04:00 Document ID : uuid:39680ebb-b4d6-4047-9e48-71a0a3ba629a Instance ID : uuid:14675df6-e047-4842-b569-c637ec804614 Subject : 16 Format : application/pdf Creator : 윤수권 Title : User's Manual Has XFA : No Page Count : 22 Page Layout : OneColumn Author : 윤수권EXIF Metadata provided by EXIF.tools