LG Electronics USA MU60PZ90V 60-inch Plasma Display Monitor User Manual EMISSION TEST REPORT

LG Electronics USA 60-inch Plasma Display Monitor EMISSION TEST REPORT

Users Manual

PLASMA MONITOROWNER’S MANUALPlease read this owner’s manual carefully before operating theMonitor.Retain it for future reference.Record model number and serial number of the Monitor.See the label attached on the back of the Monitor and quotethis information to your dealer when you require service.Model number : Serial number : MODELS:MU-60PZ90M/90VMU-60PZ90MA/90VAMU-60PZ90MB/90VBMU-60PZ90MK/90VKMU-60PZ90MR/90VRMU-60PZ90MS/90VS
2 Plasma DisplayWarningWARNING:TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user tothe presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of suffi-cient magnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presence ofimportant operating and maintenance (servicing) instructions in the literature accompanying the appli-ance.WARNING:TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.FCC NOTICE• A Class B digital deviceThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina residential installation. This equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help.• Any changes or modifications not expressly approved by the party responsible for compli-ance could void the user’s authority to operate the equipment.WARNINGRISK OF ELECTRIC SHOCK DO NOT OPENWARNINGTO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.WWarningarning
Owner’s Manual 3Safety InstructionsImportant safeguards for you and your new productYour product has been manufactured and tested with your safety in mind. However, improper use can result in potential elec-trical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read andobserve the following safety points when installing and using your new product, and save them for future reference.Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operationthat are built into your new product.This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian StandardsAssociation.1. Read InstructionsAll the safety and operating instructions should be readbefore the product is operated.2. Follow InstructionsAll operating and use instructions should be followed.3. Retain InstructionsThe safety and operating instructions should be retained forfuture reference.4. Heed WarningsAll warnings on the product and in the operating instructionsshould be adhered to.5. CleaningUnplug this product from the wall outlet before cleaning. Donot use liquid cleaners or aerosol cleaners. Use a dampcloth for cleaning.6. Water and MoistureDo not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet base-ment, or near a swimming pool.7. Accessories Carts and StandsDo not place this product on a slippery or tilted surface, or onan unstable cart, stand, tripod, bracket, or table. The productmay slide or fall, causing serious injury to a child or adult,and serious damage to the product. Use only with a cart,stand, tripod, bracket, or table recommended by the manu-facturer, or sold with the product. Any mounting of the prod-uct should follow the manufacturer’s instructions, and shoulduse a mounting accessory recommended by the manufac-turer.8. Transporting ProductA product and cart combination should be moved with care.Quick stops, excessive force, and uneven surfaces maycause the product and cart combination to overturn.9. AttachmentsDo not use attachments not recommended by the productmanufacturer as they may cause hazards.10. VentilationSlots and openings in the cabinet are provided for ventilationand to ensure reliable operation of the product and to protectit from overheating, and these openings must not be blockedor covered. The openings should never be blocked by plac-ing the product on a bed, sofa, rug, or other similar surface.This product should not be placed in a built-in installationsuch as a bookcase or rack unless proper ventilation is pro-vided or the manufacturer’s instructions have been adheredto.11. Power SourcesThis product should be operated only from the type of powersource indicated on the marking label. If you are not sure ofthe type of power supply to your home, consult your productdealer or local power company. For products intended tooperate from battery power, or other sources, refer to theoperating instructions.12. Power-Cord PolarizationThis product is equipped with a three-wire grounding typeplug, a plug having a third (grounding) pin. This plug will onlyfit into the grounding-type power outlet. This is a safety fea-ture. If you are unable to insert the plug into the outlet, con-tact your electrician to replace your obsolete outlet. Do notdefeat the safety purpose of the grounding-type plug.13. Power-Cord ProtectionPower-supply cords should be routed so that they are notlikely to be walked on or pinched by items placed upon oragainst them, paying particular attention to cords at plugs,convenience receptacles, and the point where they exit fromthe product.PORTABLE CART WARNING(Continued on next page)Safety InstructionsSafety Instructions
4 Plasma DisplaySafety InstructionsAntenna Lead in WireAntenna Discharge Unit(NEC Section 810-20)Grounding Conductor(NEC Section 810-21)Ground ClampsPower Service GroundingElectrode System (NECArt 250, Part H)Ground ClampElectric ServiceEquipmentExample of Grounding According to NationalElectrical Code InstructionsNEC - National Electrical Code14. Outdoor Antenna GroundingIf an outside antenna or cable system is connected to theproduct, be sure the antenna or cable system is grounded soas to provide some protection against voltage surges andbuilt-up static charges. Article 810 of the National ElectricalCode (U.S.A.), ANSI/ NFPA 70 provides information withregard to proper grounding of the mast and supporting struc-ture, grounding of the lead-in wire to an antenna dischargeunit, size of grounding conductors, location of antenna-dis-charge unit, connection to grounding electrodes, andrequirements for the grounding electrode. 15. Lightning For added protection for this product (receiver) during a light-ning storm, or when it is left unattended and unused for longperiods of time, unplug it from the wall outlet and disconnectthe antenna or cable system. This will prevent damage to theproduct due to lightning and power-line surges.16. Power LinesAn outside antenna system should not be located in thevicinity of overhead power lines or other electric light orpower circuits, or where it can fall into such power lines orcircuits. When installing an outside antenna system, extremecare should be taken to keep from touching such power linesor circuits as contact with them might be fatal.17. OverloadingDo not overload wall outlets and extension cords as this canresult in a risk of fire or electric shock.18. Object and Liquid EntryNever push objects of any kind into this product throughopenings as they may touch dangerous voltage points orshort-out parts that could result in a fire or electric shock.Never spill liquid of any kind on the product.19. ServicingDo not attempt to service this product yourself as opening orremoving covers may expose you to dangerous voltage orother hazards. Refer all servicing to qualified service per-sonnel.20. Damage Requiring ServiceUnplug this product from the wall outlet and refer servicing toqualified service personnel under the following conditions:a. If the power-supply cord or plug is damaged.b. If liquid has been spilled, or objects have fallen into theproduct.c. If the product has been exposed to rain or water.d. If the product does not operate normally by following theoperating instructions. Adjust only those controls that arecovered by the operating instructions as an improperadjustment of other controls may result in damage andwill often require extensive work by a qualified technicianto restore the product to its normal operation.e. If the product has been dropped or the cabinet has beendamaged.f. If the product exhibits a distinct change in performance.21. Replacement PartsWhen replacement parts are required, be sure the servicetechnician has used replacement parts specified by the man-ufacturer or have the same characteristics as the originalpart. Unauthorized substitutions may result in fire, electricshock, or other hazards.22. Safety CheckUpon completion of any service or repairs to this product,ask the service technician to perform safety checks to deter-mine that the product is in proper operating condition.23. Wall or Ceiling MountingThe product should be mounted to a wall or ceiling only asrecommended by the manufacturer. The product may slideor fall, causing serious injury to a child or adult, and seriousdamage to the product.24. HeatThe product should be situated away from heat sourcessuch as radiators, heat registers, stoves, or other products(including amplifiers) that produce heat.(Continued from previous page)Safety Instructions continuedSafety Instructions continued
Owner’s Manual 5ContentsAfter reading this manual, keep it handy for future reference.Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4IntroductionControls and Connection Options . . . . . . . . . . . .7Remote Control Key Functions . . . . . . . . . . . . . .8InstallationInstallation Instruction . . . . . . . . . . . . . . . . . . . .9~10External Equipment Connections . . . . . . . . . .11~14VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .11Cable TV Setup . . . . . . . . . . . . . . . . . . . . . . . .11External A/V Source Setup . . . . . . . . . . . . . . . .12DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12DTV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .12PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .13~14OperationTurning on the Monitor . . . . . . . . . . . . . . . . . . . . .15Menu Language Selection . . . . . . . . . . . . . . . . . .15Video Menu OptionsAPC (Auto Picture Control) . . . . . . . . . . . . . . . .16Manual Picture Control . . . . . . . . . . . . . . . . . . .16Adjusting Auto Color Control . . . . . . . . . . . . . . .16Manual Color Temperature Control . . . . . . . . . .16Audio Menu OptionsDASP (Digital Auto Sound Processing) . . . . . . .17Manual Sound Control . . . . . . . . . . . . . . . . . . .17AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .17Time Menu OptionsSetting the Clock . . . . . . . . . . . . . . . . . . . . . . .18Setting the On/Off Timer . . . . . . . . . . . . . . . . .18Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . .18Special Menu OptionsKey Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .19Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Menu Rotation For Vertical Viewing . . . . . . . . . .19Screen Menu OptionsAuto Adjustment . . . . . . . . . . . . . . . . . . . . . . . .20Setting Picture Format . . . . . . . . . . . . . . . . . . .20Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . .20Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .21Screen Position . . . . . . . . . . . . . . . . . . . . . . . .21Manual Configure . . . . . . . . . . . . . . . . . . . . . . .21Screen Adjustments . . . . . . . . . . . . . . . . . . . . .22Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Selecting Wide VGA/XGA mode . . . . . . . . . . . .22PIP (Picture In Picture) FeatureWatching PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23PIP Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . .23Swapping PIP . . . . . . . . . . . . . . . . . . . . . . . . . .23Moving PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .23Selecting a Input Signal Source for PIP . . . . . . .23Twin Picture Setup OptionsMain Picture Size Adjustment . . . . . . . . . . . . . .24Sub Picture Size Adjustment . . . . . . . . . . . . . . .24Swapping the Twin Picture . . . . . . . . . . . . . . . .24Selecting a Source for the Twin Picture . . . . . . .24External Control Device Setup . . . . . . . . . . . . . . . .25~30IR Code (NEC format) . . . . . . . . . . . . . . . . . . . . . . .31~32Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .33Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35ContentsContentsSetup and Operation ChecklistSetup and Operation ChecklistSetup and Operation Checklist(See pages 11~13 for available connection and operational setup options.)1. Unpack Monitor and all accessories.2. Connect all external video and audio equipment.see pages 11 ~ 13.3 Install batteries in remote control.See page 8.4. Turn Monitor on.See page 15.5. Turn video source equipment on.6. Select viewing source for Monitor.See page 8.7. Fine-tune source image and sound to personal preferenceor as required by source. See pages 16 ~ 17.8. Additional features SetupSee Contents above.
6 Plasma DisplayIntroductionIntroductionIntroductionWhat is a Plasma Display Panel (PDP)?If voltage is inputted to gas in glass panels, ultraviolet rays is outputted and fused with a fluorescent substance. At this moment,light is emitted. A Plasma Display is a next generation flat Display using this phenomenon. 160° - Wide angle range of visionYour flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display isclear for audience members anywhere in the room. Wide ScreenThe screen of a Plasma Display is 60" so that you can get vivid experience as if you are in a theater.MultimediaConnect your plasma display to a PC and you can use it for conferencing, games, and internet browsing. The Picture-in-Picturefeature allows you to view your PC and video images simultaneously.VersatileThe light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional displaysdon’t fit.The PDP Manufacturing Process: Why colored dots may be present on the PDP screenThe PDP (Plasma Display Panel) which is the display device of this product is composed of 0.9 to 2.2 million cells. A few celldefects will normally occur in the PDP manufacturing process. Several colored dots visible on the screen should be acceptable.This also occurs in other PDP manufacturers' products and the dots appearing does not mean that this PDP is defective. Thus afew cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology is designed to mini-mize cell defects.during the operation of this product. We hope you understand that a certain level of noise from the cooling fans isacceptable and is not sufficient cause for the PDP to be exchanged or returned.Cooling Fan NoiseIn the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped withcooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operat-ing and cooling the PDP.This noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during theoperation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not suffi-cient cause for the PDP to be exchanged or returned.WARNINGTO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TORAIN OR MOISTURE.
Owner’s Manual 7IntroductionControlsControlsConnection OptionsConnection OptionsR( )( )( )( )LRS-232C INPUT(CONTROL/SERVICE)EXTERNAL SPEAKERYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAC INPUTAUDIO INPUTVIDEO INPUTAUDIO INPUTAUDIO INPUTREMOTECONTROLCOMPONENT INPUTDVI INPUT RGB INPUT RGB OUTPUT11. EXTERNAL SPEAKER (8 ohm output)Connect to optional external speaker(s).* For further information, refer to ‘Speaker & SpeakerStand’manual.2. RS-232C INPUT (CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.3. DVI (Digital Visual Interface) INPUT/RGB INPUT/AUDIO INPUT JACKSConnect the monitor output connector of a PC to the appro-priate input port.4. RGB OUTPUT JACKSYou can watch the RGB signal on another monitor, connectRGB OUTPUT to another monitor’s PC input port.5. REMOTE CONTROLConnect your wired remote control to the remote controlport on the Monitor.6. COMPONENT INPUT/AUDIO INPUT JACKS7. S-VIDEO INPUTSConnect video out from an S-VIDEO VCR to the S-VIDEOinput.AUDIO/VIDEO INPUT JACKSConnect audio/video out from external equipment to thesejacks.8. POWER CORD SOCKETThis Monitor operates on an AC power. The voltage is indi-cated on the Specifications page. Never attempt to operatethe Monitor on DC power.Back Connection PanelBack Connection PanelVOL.MENUINPUT SELECTON/OFFMain Power Button INPUT SELECT Button VOLUME (F,G) ButtonsPower Standby IndicatorIlluminates red in standby mode,Illuminates green when theMonitor is turned on.Remote Control Sensor MENU ButtonE, D ButtonsFront Panel ControlsFront Panel Controls2 4 53 7 86
8 Plasma DisplayIntroduction- When using the remote control, aim it at the remote control sensor on the monitor. - Under certain conditions such as when the beam is interrupted, the remote control may not function. Press the keyagain if necessary.1234567809POWERSLEEP INPUT SELECTAPC DASPARC PIP ARCPIPTWIN PICTURESWAPMENU MUTEOKVOLPOWER STOPPLAY FFRECREWP/STILLWIN.SIZEWIN.POSITIONZOOM +ZOOM -SPLIT ZOOMVOLSUB INPUTPOWERSwitches the Monitor on fromstandby or off to standby.SLEEPSets the sleep timer.(Refer to p.18)APCAdjusts the factory preset pictureaccording to the room. (Refer to p.16)ARC Changes the picture format.(Refer to p.20)PIPSwitches the sub picture on or off.(Refer to p.23)SWAPExchanges main and sub pictureimages. (Refer to p.23, 24)MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.NUMBER buttonsWIN. SIZEAdjusts the sub picture size.WIN.POSITIONMoves the sub picture.SPLIT ZOOMEnlarge the screen with regularration.ZOOM-/ZOOM+Enlarges or reducesthe main picture size.VCR BUTTONSControls a LG video cassetterecorder.OKD / ESelects a menu option.F / G (Volume button)Increases/decreases sound level.Adjusts menu settings.INPUT SELECTSelects: Video,S-Video,RGB,DVIor Component mode.DASPTo select the sound appropriate toyour viewing program character:Flat,Music, Cinema,Sports,orUser (Refer to p.17)PIP ARC Changes the PIP picture format.(Refer to p.23)SUB INPUTSelects the input mode for the subpicture.MUTESwitches the sound on or off.TWIN PICTURE(Refer to p.24)•Open the battery compartment cover on the back side andinsert the batteries with correct polarity.•Install two 1.5V alkaline batteries of AAA type. Don’t mix usedbatteries with new batteries.Installing BatteriesInstalling BatteriesRemote Control Key FunctionsRemote Control Key Functions
Owner’s Manual 9InstallationInstallationInstallationD-sub 15 pin cableOwner’s Manual1.5V1.5VAlkaline batteries BNC-RCA adapterPower Cord1234567809POWERSLEEP INPUT SELECTAPC DASPARC PIP ARCPIPTWIN PICTURESWAPMENU MUTEOKVOLPOWER STOPPLAY FFRECREWP/STILLWIN.SIZEWIN.POSITIONZOOM +ZOOM -SPLIT ZOOMVOLSUB INPUTRemote ControlDVI-D CableEnsure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealerwhere you purchased the product.Installation InstructionsInstallation Instructions•The Monitor can be installed in various ways such such as on a wall, or on a desktop etc.•The plasma display is designed to be mounted horizontally or vertically. The speakers depicted are optional.GROUNDINGEnsure that you connect the grounding / earth wire to prevent possibleelectric shock. If grounding methods are not possible, have a qualifiedelectrician install a separate circuit breaker. Do not try to ground theunit by connecting it to telephone wires, lightening rods, or gas pipes.PowersupplierShort-circuitbreaker4inch4inch4inch4inch1.18inchWWall Mount Installationall Mount InstallationFor proper ventilation, allow a clearance of 4” on eachside and 2” from the wall. Detailed installation instruc-tions are included from your dealer in the optional WallMounting Bracket Installation and Setup Guide.
10 Plasma DisplayInstallationWWall Mount: Vall Mount: Vertical installationertical installationDetailed installation instructions are included from yourdealer in the optional Vertical Wall Mounting BracketInstallation and Setup Guide.NOTE: When installing the monitor vertically, the frontpanel controls must be in the left side position.When installing the monitor vertically, youhave to change the OSD display mode sothat the menus will appear correctly and alsoto protect the monitor from overheating(Refer to P. 19).4inch4inch2.36inch4inch1.18inchDesktop Pedestal InstallationDesktop Pedestal InstallationFor proper ventilation, allow a clearance of 4” on eachside and the top, 2.36” on the bottom, and 2” from thewall. Detailed installation instructions are included fromyour dealer in the optional Desktop Stand Installation andSetup Guide.Installation Instructions continuedInstallation Instructions continued
Owner’s Manual 11InstallationExternal Equipment ConnectionsExternal Equipment ConnectionsNOTE: Not all depicted cables are included with the plasma display.- To avoid picture noise (interference), leave an adequate distance between the VCR and Monitor- Use the orbiter function to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still pic-ture from a VCR. If a 4:3 picture format is used; the fixed image may remain visible on the screen.How to connect1. Connect the provided BNC-RCA adapter to the monitor’s VIDEOINPUT.2. Connect the audio and video cables between the VCR's outputjacks and the monitor input jacks, as shown in the figure. When con-necting the monitor to VCR, match the colors of connecting jacks(Video = yellow, Audio Left = white, and Audio Right = red).Mono VCR: Connect the video output cable from the VCR to theVIDEO input.S-VIDEO VCR: Connect the S-Video output cable from the VCR tothe S-VIDEO input. (Note that S-Video offers higher quality).How to use1. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) 2. Use the INPUT SELECT button on the remote control to selectVideo.(If connected to S-VIDEO, select the S-Video external input source.)VCR SetupVCR SetupS-VIDEO OUTIN(R) AUDIO (L) VIDEOYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAUDIO INPUTVIDEO INPUTAUDIO INPUT COMPONENT INPUT- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming.The monitor cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the Monitor.- For further information regarding cable TV service, contact your local cable TV service provider(s).How to connect1. Connect the provided BNC-RCA adapter to the monitor’s VIDEOINPUT.2. Connect the audio and video cables between the cable TV's outputjacks and the monitor input jacks, as shown in the figure. When connecting the monitor to VCR, match the colors of connect-ing jacks (Video = yellow, Audio Left = white, and Audio Right = red).How to use1. Use the INPUT SELECT button on the remote control to selectVideo.2. Select your desired channel with the remote control for cable box.Cable Cable TV SetupTV SetupTVVCR RF Cable (R) AUDIO (L) VIDEOYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAUDIO INPUTVIDEO INPUTAUDIO INPUTCOMPONENT INPUTVCRCable TV
12 Plasma DisplayInstallation•Component Input portsTo get better picture quality, connect a DVD player to the compo-nent input ports as shown below.- To watch digitally broadcast programs, purchase andconnect a digital set-top box.- This monitor supports HDCP (High-bandwidth DigitalContents Protection) protocol for DVI DTV(480p,720p,1080i) mode.How to connect1. Use the monitor’s COMPONENT (Y, PB, PR) INPUT,RGB or DVI jack for video connections, depending onyour set-top box connector. Then, make the corre-sponding audio connections.How to use1. Turn on the digital set-top box. (Refer to the owner’smanual for the digital set-top box.) 2. Use INPUT SELECT on the remote control to selectComponent, RGB or DVI.DTV SetupDTV SetupHow to connect1. Connect the provided BNC-RCA adapter to the monitor’sVIDEO INPUT.2. Connect the audio and video cables between the externalequipment's output jacks and the monitor input jacks, asshown in the figure. When connecting the monitor to exter-nal equipment, match the colors of connecting jacks (Video= yellow, Audio Left = white, and Audio Right = red).How to use1. Use the INPUT SELECT button on the remote control toselect Video.2. Operate the corresponding external equipment. Refer exter-nal equipment operating guide.Component ports of theMonitor YPBPRVideo output ports of DVD playerYYYYPbB-YCbPBPrR-YCrPRHow to connect1. Connect the DVD video outputs to the COMPONENT (Y, PB, PR)INPUT jacks and connect the DVD audio outputs to the AUDIOINPUT jacks, as shown in the figure.2. If your DVD only has an S-Video output jack, connect this to theS-VIDEO input on the monitor and connect the DVD audio outputsto the AUDIO INPUT jacks, as shown in the figure.How to use1. Turn on the DVD player, insert a DVD2. Use the INPUT SELECT button on the remote control to selectComponent. (If connected to S-VIDEO, select the S-Video exter-nal input source.)3. Refer to the DVD player's manual for operating instructions.External External A/V Source SetupA/V Source SetupDVD SetupDVD SetupRLAUDIO VIDEOVideo game setCamcorderYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAUDIO INPUTVIDEO INPUTAUDIO INPUTCOMPONENT INPUTYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAUDIO INPUTVIDEO INPUTAUDIO INPUTAUDIO INPUTREMOTECONTROLCOMPONENT INPUTDVI INPUT RGB INPUT RGB OUTPUTBR(R) AUDIO (L)RGB-DTV OUTPUT DVI-DTV OUTPUT(R) AUDIO (L)BR(R) AUDIO (L) (R) AUDIO (L)S-VIDEOYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAUDIO INPUTVIDEO INPUTAUDIO INPUTCOMPONENT INPUTDVDDigital Set-top boxororor
Owner’s Manual 13InstallationHow to connect1. To get the best picture quality, adjust the PCgraphics card to a 1024x768, 60Hz. Resolutionsover UXGA cannot be displayed.2. Use the monitor’s RGB INPUT or DVI (DigitalVisual Interface) INPUT port for video connections,depending on your PC connector. If the graphic card on the PC does not output ana-log and digital RGB simultaneously, connect onlyone of both RGB INPUT or DVI INPUT to displaythe PC on the monitor.If the graphic card on the PC does output analogand digital RGB simultaneously, set the monitor toeither RGB or DVI; (the other mode is set to Plugand Play automatically by the monitor.)3. Then, make the corresponding audio connections.If using a sound card, adjust the PC sound asrequired.How to use1. Turn on the PC and the monitor.2. Turn on the display by pressing the POWER button on the monitor's remote control.3. Use the INPUT SELECT button on the remote control to select the RGB or DVI.4. Check the image on your monitor. There may be noise associated with the resolution, vertical pattern, contrast orbrightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate toanother rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PCgraphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable. • Avoid keeping a fixed image on the monitor's screen for a long period of time.The fixed image may becomepermanently imprinted on the screen. Use the Orbiter screen saver when possible.• The synchronization input form for Horizontal and Vertical frequencies is separate.PC SetupPC SetupR( )( )( )( )LRS-232C INPUT(CONTROL/SERVICE)EXTERNAL SPEAKERAUDIO INPUTREMOTECONTROLDVI INPUT RGB INPUT RGB OUTPUT- This monitor display provides Plug and Play capability, meaning that the PC adjusts automatically to its settings. The monitorsends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display DataChannel (DDC) protocol. - The monitor perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. In this case, change the screen scanningrate for the graphic card.
Owner’s Manual 15OperationOperationOperationMenu Language SelectionMenu Language SelectionTTurning on the Monitorurning on the MonitorTurning on the Monitor just after installationTurning on the Monitor (power cord is still connected)1. Connect power cord correctly.2. Press the ON/OFF button on the Monitor. At this moment, the Monitor is switched to standbymode. Press the INPUT SELECT button on the Monitor or press the POWER, INPUT SELECT but-ton on the remote control and then the Monitor will switch on.•Press the ON/OFF button on the Monitor to turn the Monitor on.1. If the Monitor was turned off with the ON/OFF button on the Monitor2. If the Monitor was turned off with the remote control and then the ON/OFF button on the Monitor•Press the ON/OFF button on the Monitor and then press the INPUT SELECT button on theMonitor or press the POWER, INPUT SELECT button on the remote control to turn the Monitor on.-The menus can be shown on the screen in the selected language. First select your language.1. Press the MENU button and then use D/ Ebutton to select the SPECIAL menu.2. Press the Gbutton and then use D/ Ebutton to select Language. 3. Press the Gbutton and then use D/ Ebutton to select your desired language.From this point on, the on-screen menus will be shown in the language of your choice.4. Press the MENU button to save.한국어VIDEOAUDIOTIMESCREENTWINSPECIALLanguage GKey lock ISM MethodLow powerSet ID.OSD RotateEnglishEspañolPortuguêsFrançaisMENU Prev.
16 Plasma DisplayOperation- You can adjust picture contrast, brightness, color, sharpness and tint to the levels you prefer.- PIP settings are not adjustable.1. Press the MENU button and then use D / Ebutton to select the VIDEO menu.2. Press the Gbutton and then use D / Ebutton to select the desired picture option(Contrast,Brightness,Color,Sharpness,Tint).3. Press the Gbutton and then use F / Gbutton to make appropriate adjustments.4. Press the MENU button to save.1. Press the APC button repeatedly to select the picture appearance setup option as shown below.APC (Auto Picture Control)APC (Auto Picture Control)Manual Picture Control (Manual Picture Control (User option)option)- To initialize values (reset to default settings), select the Normal option.- When adjusting color temperature options (red, green and blue) manually, ACC automatically changes to User.1. Press the MENU button and then use D / Ebutton to select the VIDEO menu.2. Press the Gbutton and then use D / Ebutton to select ACC . 3. Press the Gbutton and then use D / Ebutton to select either Normal (Default), Cool(Preset), Warm (Preset) or User (Manual Adjustment).4. Press the MENU button to save.Adjusting Adjusting Auto Color ControlAuto Color Control- APC adjusts the Monitor for the best picture appearance.- When adjusting picture options (contrast, brightness, color, sharpness and tint) manually, APC automaticallychanges to User.- You can adjust red, green, or blue to any color temperature you prefer.1. Press the MENU button and then use D / Ebutton to select the VIDEO menu.2. Press the Gbutton and then use D / Ebutton to select the Color temp . 3. Press the Gbutton and then use D / Ebutton to select Red, Green or Blue.4. Use the F / Gbutton to make appropriate adjustments.• The adjustment range of Red, Green,and Blue is -20 ~ +20.5. Press the MENU button to save.Manual Color Manual Color TTemperature Control (emperature Control (User option)option)VIDEOAUDIOTIMESCREENTWINSPECIALAPCACCColor temp.Contrast 85 GBrightness 60Color 50Sharpness 50Tint 0MENU Prev.VIDEOAUDIOTIMESCREENTWINSPECIALAPCACC GColor temp.Contrast 85Brightness 60Color 50Sharpness 50Tint 0NormalCoolWarmUserMENU Prev.000VIDEOAUDIOTIMESCREENTWINSPECIALAPCACCColor temp. GContrast 85Brightness 60Color 50Sharpness 50Tint 0RedGreenBlueMENU Prev.- Each adjustment for video menu options doesn’t effect other input source. Readjust Video menu foreach following mode.: RGB (PC) / DVI (DVI),: RGB (DTV) / DVI (DTV) / Component (480p, 720p, 1080i): Video / S-Video / Component (480i)VVideo Menu Optionsideo Menu Options•You can also select Clear, Optimum, Soft or User in the VIDEO menu. •Clear, Optimum and Soft are preset for good picture quality at the factory and cannot be changed.Clear Optimum Soft User
Owner’s Manual 17OperationAudio Menu OptionsAudio Menu Options1. Use the DASP button repeatedly to select the appropriate sound setup as shown below.DASPDASP (Digital (Digital Auto Sound Processing)Auto Sound Processing)1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D / Ebutton to select the desired sound option(Balance,Treble,Bass). 3. Press the Gbutton and then use F / Gbutton to make appropriate adjustments.4. Press the MENU button to save.Manual Sound Control (Manual Sound Control (User option)option)- This function lets you enjoy the best sound without any special adjustment because the Monitor automaticallyselects the appropriate sound option based on the program content.- When adjusting sound options (treble, bass, and balance) manually, DASP automatically changes to User.- This feature maintains an equal volume level; even if you change channels.1. Press the MENU button and then use D / Ebutton to select the AUDIO menu.2. Press the Gbutton and then use D / Ebutton to select AV L . 3. Press the Gbutton and then use D / Ebutton to select On or Off.4. Press the MENU button to save.AAVLVL (Auto V(Auto Volume Leveler)olume Leveler)VIDEOAUDIOTIMESCREENTWINSPECIALDASPAVLBalance 0 Treble 50 GBass 50MENU PREV.VIDEOAUDIOTIMESCREENTWINSPECIALDASPAVL GBalance 0Treble 50Bass 50OnOffMENU PREV.•You can also select Flat, Music, Cinema, Sports, or User in the AUDIO menu.•Flat, Music, Cinema and Sports are preset for good sound quality at the factory and cannot bechanged.Flat Music Cinema Sports User
18 Plasma DisplayOperation- Timer function operates only if current time has been already set.- Off-Timer function overrides On-Timer function if they are set to the same time.- The monitor must be in standby mode for the On Timer to work.Setting the On/OfSetting the On/Off f TTimerimer1. Press the MENU button and then use D / Ebutton to select the TIME menu.2. Press the Gbutton and then use D / Ebutton to select Off timer or On timer.3. Press the Gbutton and then use D / Ebutton to select On.• To cancel On/Off timer function, select Off.4. Press the Gbutton and then use D / Ebutton to set the hour.5. Press the Gbutton and then use D / Ebutton to set the minutes.6. For only On timer function; Press the Gbutton and then use D / Ebutton to set volume level.6. Press the MENU button to save.Auto OfAuto Offf- If there is no input signal, the Monitor turns off automatically after 10 minutes.1. Press the MENU button and then use D / Ebutton to select the TIME menu.2. Press the Gbutton and then use D / Ebutton to select Auto off.3. Press the Gbutton and then use D / Ebutton to select On or Off.4. Press the MENU button to save.12 0030:VIDEOAUDIOTIMESCREENTWINSPECIALClock Off timerOn timer GAuto offOff OnVol.MENU Prev.VIDEOAUDIOTIMESCREENTWINSPECIALClock Off timerOn timerAuto off GOffOnMENU Prev.Setting the ClockSetting the Clock- If current time setting is erased by a power failure, if TV is unplugged or if the monitor is turned off withthe ON/OFF button on the monitor, reset the clock.1. Press the MENU button and then use D / Ebutton to select the TIME menu.2. Press the Gbutton and then use D / Ebutton to select Clock. 3. Press the Gbutton and then use D / Ebutton to set the hour.4. Press the Gbutton and then use D / Ebutton to set the minutes.5. Press the MENU button to save.-- --:VIDEOAUDIOTIMESCREENTWINSPECIALClock GOff timerOn timerAuto offMENU Prev.TTime Menu Optionsime Menu OptionsSleep Sleep TTimerimer- The sleep timer turns the Monitor off at a preset time. Note that this setting is cleared when the monitor is turned off.1. Press the SLEEP button repeatedly to select the number of minutes. First the --- Min option appears on thescreen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.2. When the number of minutes you want is displayed on the screen, press the OK button. The timer begins to countdown from the number of minutes selected.3. To check the remaining minutes before the monitor turns off, press the SLEEP or OK button once.4. To cancel the Sleep Timer, press the SLEEP button repeatedly until --- Min appears.zzzz
Owner’s Manual 19OperationSpecial Menu OptionsSpecial Menu OptionsVIDEOAUDIOTIMESCREENTWINSPECIALLanguage Key lockISM Method GLow powerSet ID.OSD RotateNormal White washOrbiterInversionMENU Prev.VIDEOAUDIOTIMESCREENTWINSPECIALlanguage Key lockISM Method Low power GSet ID.OSD RotateOn OffMENU Prev.VIDEOAUDIOTIMESCREENTWINSPECIALLanguage Key lockISM Method Low power Set ID.OSD Rotate GMENU Prev.Menu Rotation for VMenu Rotation for Vertical Vertical Viewingiewing1. Press the MENU button and then use the D / Ebutton to select the SPECIAL menu.2. Press the Gbutton and then use the D / Ebutton to select OSD Rotate.3. Press the Gbutton and then use the D / Ebutton to select Normal or Rotate.• Select Normal, if the monitor was installed horizontally.• Select Rotate, if the monitor was installed vertically.4. Press the MENU button to save.Key LockKey Lock- The monitor can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing.- This Monitor is programmed to remember which option it was last set to even if you turn the monitor off.1. Press the MENU button and then use D / Ebutton to select the SPECIAL menu.2. Press the Gbutton and then use D / Ebutton to select Key lock.3. Press the Gbutton and then use D / Ebutton to select On or Off.• When you select On, the display ‘ Key lock’appears on the screen if any buttonon the front panel is pressed.4. Press the MENU button to save.VIDEOAUDIOTIMESCREENTWINSPECIALLanguage Key lock GISM MethodLow powerSet ID.OSD RotateOn OffMENU Prev.-In setting Key lock ‘On’, if the monitor is turned off with the remote control, press the INPUT SELECT buttonon the monitor or POWER, INPUT SELECT on the remote control to turn the monitor on.WNormalRotate- Frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghostimage remaining even when you change the image. Avoid allowing a fixed image to remain on the Monitor's screenfor a long period of time.1. Press the MENU button and then use D / Ebutton to select the SPECIAL menu.2. Press the Gbutton and then use D / Ebutton to select ISM Method.3. Press the Gbutton and then use D / Ebutton to select either Normal, White wash,Orbiter or Inversion. If you unnecessary to set this function, set Normal.• White wash: White Wash removes permanent images from the screen. Note: An excessive perma-nent image may be impossible to clear entirely with White Wash. To return to normalviewing, press the any button.• Orbiter: Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoida permanent image on the screen, the screen will move every 1 minutes: Left →Left → Upside →Upside →Right →Right →Downside →Downside.• Inversion: This is the function to invert the panel color of monitor. The panel color is automatically inverted every 30 minutes.4. Press the MENU button to save.Low powerLow power- This is the function to reduce the power consumption of the monitor.1. Press the MENU button and then use D / Ebutton to select the SPECIAL menu.2. Press the Gbutton and then use D / Ebutton to select Low power.3. Press the Gbutton and then use D / Ebutton to select On or Off.• When you select On, the screen becomes dim.4. Press the MENU button to save.ISM (Image Sticking Minimization) methodISM (Image Sticking Minimization) method
20 Plasma DisplayOperationAuto Auto AdjustmentAdjustment- RGB (PC) mode only; This function doesn’t work in RGB-DTV.- Automatically adjusts picture position and minimizes image shaking.- If the image is still not correct, your Monitor is functioning properly but needs further adjustment.- The Auto config. and the Manual config. can be adjust automatically for DVI mode.1. Press the MENU button and then use D / Ebutton to select the SCREEN menu.2. Press the Gbutton and then use D / Ebutton to select Auto config..3. Press the Gbutton to run Auto configure.• When Auto config. has finished, OK will be shown on screen.• If the position of the image is still not correct, try Auto adjustment again.4. If picture needs to be adjusted more after Auto adjustment in RGB (PC)mode, you canadjust the Manual config..VIDEOAUDIOTIMESCREENTWINSPECIALAuto config. GARCZoom in/outPositionManual config.Screen adj.ResetXGA ModeTo setMENU Prev.Screen Menu OptionsScreen Menu OptionsSetting Picture FormatSetting Picture Format- If a 4:3 fixed image is on the screen for a long time, it may remain visible.-It’s available to use every aspect ratio in DTV 480p, Component 480i/480p, video, and S-video. -It’s available to use 4:3, 16:9 in the rest input source only. 1. Use the ARC button repeatedly to select the desired picture format. You can also select picture format 4:3, 16:9,Horizon or ZOOM in the SCREEN menu.• 4:3- Choose when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both theleft and right sides.• 16:9- Choose when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.• Horizon- Choose when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, tocreate a spectacular view.• ZOOM- Choose when you want to view the picture without any alteration. However, the top and bottom portions of thepicture will be cropped.1. Use ZOOM+/ZOOM- button to enlarge or reduce the picture size.• The adjustment range of Zoom is 100~300.2. Adjust the main picture position with the D / E/ F / G buttons in enlarged picture mode.Picture Size ZoomPicture Size Zoom- When enlarging or reducing the picture, the image may become distorted.Zoom out100%DFGE
Owner’s Manual 21Operation14▲▼◀▶2-Split zoom▲▼◀▶12544-Split zoom▲▼◀▶12 34567899-Split zoomManual Configure (RGB-PC mode only)Manual Configure (RGB-PC mode only)- If the picture isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture phasemanually.- To correct the screen size, adjust Clock.1. Press the MENU button and then use D / Ebutton to select the SCREEN menu.2. Press the Gbutton and then use D / Ebutton to select Manual config..3. Press the Gbutton and then use D / Ebutton to to select Phase or Clock.4. Use the F / Gbutton to make appropriate adjustments.• The adjustment range of Phase is 0 ~ 31.• The adjustment range of Clock is -50 ~ +50.5. Press the MENU button to save.00VIDEOAUDIOTIMESCREENTWINSPECIALAuto config. ARCZoom in/outPosition Manual config. GScreen adj.ResetXGA ModePhase ClockMENU Prev.- This function works in the following mode:RGB-PC, RGB-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i).1. Press the MENU button and then use D / Ebutton to select the SCREEN menu.2. Press the Gbutton and then use D / Ebutton to select Position.3. Press the Gbutton and then use D / E/ F / Gbutton to adjust the position.4. Press the MENU button to save.◀▶▲▼VIDEOAUDIOTIMESCREENTWINSPECIALAuto config. ARCZoom in/outPosition GManual config.Screen adj.ResetXGA ModeMENU Prev.Screen PositionScreen Position- Enlarges the picture in correct proportion.- Split Zoom can be used for every input source.- with 2-SPLIT ZOOM, you can only move the screen into upside or downside.- If a screen is enlarged, a screen can move without selecting section of screen Split Zoom.1. Press the SPLIT ZOOM button repeatedly switches between dividing the screen into 2, 4 or 9 sections.2. Press the number button corresponding to the section you wish to enlarge. you can move the enlarged screenwith using the D / E / F / Gbutton. To return to normal viewing, press the SPLIT ZOOM button again.Example of choosing 5. Section 5 is enlarged to fillthe screen.▲▼◀▶12 34567899-Split zoomSplit ZoomSplit Zoom
22 Plasma DisplayOperation1. Press the MENU button and then use D / Ebutton to select the SCREEN menu.2. Press the Gbutton and then use D / Ebutton to select Reset.3. Press the Gbutton.•You can initialize Zoom In/Out, Manual config., Position, Split zoom, PIP size, PIP posi-tion and sub picture size for twin picture.Initializing (Reset to original factory value)Initializing (Reset to original factory value)- This function operates in every mode.- To initialize the adjusted valueVIDEOAUDIOTIMESCREENTWINSPECIALAuto config. ARCZoom in/outPosition Manual config.Screen adj.Reset GXGA ModeTo set MENU Prev.1. Press the MENU button and then use D /Ebutton to select the SCREEN menu.2. Press the Gbutton and then use D /Ebutton to select VGA mode/XGA mode.3. Press the Gbutton and then use D /Ebutton to select the desired VGA/XGA resolution.4. Press the MENU button to save.Selecting WSelecting Wide VGA/XGAide VGA/XGA mode (RGB, DVI-PC mode only)mode (RGB, DVI-PC mode only)- To see a normal picture, match the resolution of RGB XGA mode (1024x768, 1360x768, 1366x768) with the selection for XGAmode and the resolution of RGB VGA mode (640x480, 848x480, 852x480) with the selection for VGA mode in the SCREENmenu.- If the input source is RGB VGA mode, the screen menu option is changed from XGA mode to VGA mode automatically.VIDEOAUDIOTIMESCREENTWINSPECIALAuto config. ARCZoom in/outPosition Manual config.Screen adj.Reset XGA Mode G1024x7681360x7681366x768MENU Prev.Screen Screen Adjustments (VAdjustments (Video, S-Video, S-Video and Component 480i mode only)ideo and Component 480i mode only)- Use this function to correct jittering or picture instability while viewing a video tape.1. Press the MENU button and then use D /Ebutton to select the SCREEN menu.2. Press the Gbutton and then use D /Ebutton to select Screen adj..3. Press the Gbutton and then use D /Ebutton to to select TV or VCR.• Select the VCR option if watching a VCR. • Select the TV option for other equipment.(Except VCR)4. Press the MENU button to save.VIDEOAUDIOTIMESCREENTWINSPECIALAuto config. ARCZoom in/outPosition Manual config.Screen adj. GResetXGA ModeTV VCRMENU Prev.Screen Menu Options continuedScreen Menu Options continued
Owner’s Manual 23OperationWWatching PIPatching PIP- PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and theother source will show a smaller inset image.- When you select PC or DTV for main picture in PIP, you can watch VIDEO, S-VIDEO or COMPONENT 480i for sub picture.Press the PIP button repeatedly to select turn PIP on or off.PIPPIP SizeSizePress the WIN.SIZE button and then use F / Gbutton tochange the sub picture size.PIPPIP Aspect RatioAspect RatioPress the PIP ARC button. The sub picture appears as shown.Moving the PIPMoving the PIPPress the WIN.POSITION button. Press the D / E/ F / Gbutton repeatedly until desired posi-tion is achieved. The sub picture moves up/down/left/right.Swapping the PIPSwapping the PIPPress the SWAP button to exchange the main and sub pictures.Selecting a Input Signal Source for the PIPSelecting a Input Signal Source for the PIPUse the SUB INPUT button to select the input source forthe sub picture.•In Video for main picture, you can select S-Video,Component 480i/480p/720p/1080i, RGB and DVI for subpicture.•In S-Video for main picture, you can select Video,Component 480i/480p/720p/1080i, RGB and DVI for subpicture.•In Component 480i for main picture, you can select RGB,DVI, Video and S-Video for sub picture.•In Component 480p/720p/1080i for main picture, you canselect Video and S-Video for sub picture.•In RGB and DVI for main picture, you can selectComponent 480i, Video and S-Video for sub picture.Main Picture Sub Picture◀▶▲▼10 : 30 10 : 3010 : 304 : 3 16 : 9Win.positionComponentVideoComponentVideoVideoComponentPIPPIP (Picture-In-Picture) Feature(Picture-In-Picture) Feature10 : 30ComponentVideoWin.sizeF G
24 Plasma DisplayOperationSelecting a Source for the Selecting a Source for the TTwin Picturewin PictureUse the SUB INPUT button to select the input source for the sub picture.•In Video for main picture, you can select S-Video, Component 480i/480p/720p/1080i,RGB and DVI for sub picture.•In S-Video for main picture, you can select Video, Component 480i/480p/720p/1080i,RGB and DVI for sub picture.•In Component 480i for main picture, you can select RGB, DVI, Video and S-Video forsub picture.•In Component 480p/720p/1080i for main picture, you can select Video and S-Video forsub picture.•In RGB and DVI for main picture, you can select Component 480i, Video and S-Videofor sub picture.Main Picture Size Main Picture Size AdjustmentAdjustmentUse the TWIN PICTURE button repeatedly to select one of the Twin Picture options.Sub Picture Size Sub Picture Size AdjustmentAdjustmentUse the WIN.SIZE button.•Use the F / Gbutton to adjust the sub picture size.•Using WIN.SIZE function in Twin Picture mode, main and sub picture are adjustedsimultaneously.Using WIN.SIZE function in PIP mode, sub picture is adjusted.•WIN.POSITION is not functional in twin picture mode.Swapping the Swapping the TTwin Picturewin PictureUse the SWAP button to switch the main and sub pictures in twin picture mode.DW 1DW 210 : 3010 : 3010 : 30◀▶OffComponentVideoComponentVideo VideoComponent- As the name suggests, this mode splits the screen into 2, allowing 2 picture sources to be shown on the monitor screen at thesame time. Each source is given half the screen.TTwin Picture Setup Optionwin Picture Setup OptionWin.sizeF GMain Picture Sub Picture
Owner’s Manual 25External Control Device SetupNo. Pin name1 No connection2 RXD (Receive data)3 TXD (Transmit data)4 DTR (DTE side ready)5 GND6 DSR (DCE side ready)7 RTS (Ready to send)8 CTS (Clear to send)9 No Connection15692354678RXDTXDGNDDTRDSRRTSCTSTXDRXDGNDDSRDTRCTSRTSPC7-wire configuration(Standard RS-232C cable)D-Sub 93256487PDPD-Sub 92354678RXDTXDGNDDTRDSRRTSCTSTXDRXDGNDDTRDSRRTSCTSPC3-wire configuration(Not standard)D-Sub 93254678PDPD-Sub 9- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)and control the Monitor’s functions externally.- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.- RS-232C connection cables are not supplied with the Monitor.TType of connector; D-Sub 9-pin maleype of connector; D-Sub 9-pin maleRS-232C configurationsRS-232C configurationsExternal Control Device SetupExternal Control Device SetupR( )( )( )( )LRS-232C INPUT(CONTROL/SERVICE)EXTERNAL SPEAKERYPBPR(MONO)RAUDIOLRAUDIOLS-VIDEOAC INPUTAUDIO INPUTVIDEO INPUTAUDIO INPUTAUDIO INPUTREMOTECONTROLCOMPONENT INPUTDVI INPUT RGB INPUT RGB OUTPUT
26 Plasma DisplayExternal Control Device SetupTransmission* [Command 1]: k and j* [Command 2]: To control PDP set.* [Set ID]: You can adjust the set ID to choose desired moni-tor ID number in special menu. Adjustment rangeis 1 ~ 99. When selecting Set ID ‘0’, every con-nected PDP set is controlled. Set ID is indicatedas decimal (1~99) on menu and as Hexa decimal(0x0~0x63) on transmission/receiving protocol.* [DATA]: To transmit command data.Transmit ‘FF’data to read status of command.* [Cr]: Carriage ReturnASCII code ‘0x0D’* [ ]: ASCII code ‘space (0x20)’[Command1][Command2][ ][Set ID][ ][Data][Cr]OK Acknowledgement* The Monitor transmits ACK (acknowledgement) based onthis format when receiving normal data. At this time, if thedata is data read mode, it indicates present status data. Ifthe data is data write mode, it returns the data of the PCcomputer.[Command2][ ][Set ID][ ][OK][Data][x]Error Acknowledgement* The Monitor transmits ACK (acknowledgement) based onthis format when receiving abnormal data from non-viable functions or communication errors.[Command2][ ][Set ID][ ][NG][x]TTransmission / Receiving Protocolransmission / Receiving Protocol01. Power k a 0 ~ 102. Input Select k b 0 ~ 403. Aspect Ratio k c 0 ~ 304. Screen Mute k d 0 ~ 105. Volume Mute k e 0 ~ 106. Volume Control k f 0 ~ 6407. Contrast k g 0 ~ 6408. Brightness k h 0 ~ 6409. Color k i 0 ~ 6410. Tint k j 0 ~ 6411. Sharpness k k 0 ~ 6412. OSD select k l 0 ~ 113. Remote control lock mode k m 0 ~ 114. PIP/Twin k n 0 ~ 315. PIP size k o 0 ~ 116. Split Zoom k p 21 ~9917. PIP position k q 0 ~ 318. Treble k r 0 ~ 6419. Bass k s 0 ~ 6420. Balance k t 0 ~ 6421. Color temperature k u 0 ~ 322. Red adjustment k v 0 ~ C823. Green adjustment k w 0 ~ C824. Blue adjustment k $ 0 ~ C825. PIP input source k y 0 ~ 426. Abnormal Status k z 0 ~ a27. ISM method j p 0 ~ 328. Low power j q 0 ~ 129. Orbiter Time Setting j r 1 ~ FE30. Orbiter Pixel Setting j s 0 ~931. Picture Size Setting j t 0 ~64for Twin Picture mode32. Auto Configure j u 1COMMAND 1 COMMAND 2 DATA(Hexadecimal)•When setting the 27 ~ 32, a menu doesn’t display onscreen.Command Reference ListCommand Reference ListSet IDSet ID- Use this function to specify a monitor ID number.- Refer to ‘Real Data Mapping 1’. See page 27.1. Press the MENU button and then use the D /Ebutton to select the SPECIAL menu.2. Press the Gbutton and then use D /Ebutton to select Set ID.3. Press the Gbutton and then use F / Gbutton to adjust Set ID to choose the desiredmonitor ID number.• The adjustment range of Set ID is 1 ~ 99.1VIDEOAUDIOTIMESCREENTWINSPECIALlanguage Key lockISM Method Low powerSet ID. GOSD RotateMENU Prev.• Baud rate : 115200 bps (UART)• Data length : 8 bits• Parity : None• Stop bit : 1 bit• Communication code : ASCII codeCommunication ParametersCommunication ParametersData 1: Illegal Code2: Not supported function3: Wait more time
Owner’s Manual 27External Control Device Setup02. Input Select (Command:b) (Main Picture Input)GTo select input source for the Monitor. You can also select an input source using the INPUTSELECT button on the Monitor's remote control.TransmissionData 0 : RGB1 : Component2 : Video3 : S-video4 : DVI[k][b][ ][Set ID][ ][Data][Cr]Acknowledgement[b][ ][Set ID][ ][OK][Data][x]01. Power (Command:a)GTo control Power On/Off of the Monitor.TransmissionData 0 : Power Off 1 : Power On[k][a][ ][Set ID][ ][Data][Cr]Acknowledgement[a][ ][Set ID][ ][OK][Data][x]GTo show Power On/Off.Transmission[k][a][ ][Set ID][ ][FF][Cr]AcknowledgementData 0 : Power Off 1 : Power On* In like manner, if other functions transmit ‘FF’data basedon this format, Acknowledgement data feed back presentsstatus about each function.[a][ ][Set ID][ ][OK][Data][x]03. Aspect Ratio (Command:c) (Main picture format)GTo adjust the screen format.You can also adjust the screen format using the ARC(Aspect Ratio Control) button on remote control or in theSpecial menu.TransmissionData 0 : Wide screen (16:9)1 : Normal screen (4:3) 2 : Full screen (Zoom) 3 : Panorama[k][c][ ][Set ID][ ][Data][Cr]Acknowledgement* Using the PC input, you select either 16:9 or 4:3 screenaspect ratio.[c][ ][Set ID][ ][OK][Data][x]05. Volume Mute (Command:e)GTo control volume mute on/off.You can also adjust mute using the MUTE button onremote control.TransmissionData 0 : Volume mute on (Volume off)1 : Volume mute off (Volume on)[k][e][ ][Set ID][ ][Data][Cr]Acknowledgement[e][ ][Set ID][ ][OK][Data][x]04. Screen Mute (Command:d)GTo select screen mute on/off.TransmissionData 0 : Screen mute off (Picture on)1 : Screen mute on (Picture off)[k][d][ ][Set ID][ ][Data][Cr]Acknowledgement[d][ ][Set ID][ ][OK][Data][x]06. Volume Control (Command:f)GTo adjust volume.You can also adjust volume with the volume buttonson remote control.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping1’as shown below.[k][f][ ][Set ID][ ][Data][Cr]Acknowledgement[f][ ][Set ID][ ][OK][Data][x]07. Contrast (Command:g)GTo adjust screen contrast. You can also adjust contrast in the Video menu.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping1’as shown below.[k][g][ ][Set ID][ ][Data][Cr]Acknowledgement[g][ ][Set ID][ ][OK][Data][x]* Real data mapping 10 : Step 0A : Step 10 (SET ID 10)F : Step 15 (SET ID 15)10 : Step 16 (SET ID 16)64 : Step 100
28 Plasma DisplayExternal Control Device Setup13. Remote Control Lock Mode (Command2:m)GTo lock the remote control and front panel controls on themonitorTransmission[k][m][ ][Set ID][ ][Data][Cr]AcknowledgementData 0: Lock off 1: Lock on•If you’re not using the remote control, use this mode.When main power is on/off, remote control lock is released.[m][ ][Set ID][ ][OK][Data][x]14. PIP / Twin (Command2:n)GTo control the PIP (Picture In picture) or TWIN picture. You can also control the PIP/TWIN using the PIP or Twin PIC-TURE button on the remote control or in the Special menu.TransmissionData 0: PIP/DW off1: PIP 2: DW13: DW2[k][n][ ][Set ID][ ][Data][Cr]Acknowledgement[n][ ][Set ID][ ][OK][Data][x]GTo adjust the screen sharpness.You can also adjust sharpness in the Video menu.Transmission11. Sharpness (Command2:k)Data Min: 0 ~ Max: 64•Refer to ‘Real data mapping1’. See page 27.[k][k][ ][Set ID][ ][Data][Cr]Acknowledgement[k][ ][Set ID][ ][OK][Data][x]12. OSD Select (Command2:l)GTo select OSD (On Screen Display) on/off.Transmission[k][l][ ][Set ID][ ][Data][Cr]AcknowledgementData 0: OSD off 1: OSD on[l][ ][Set ID][ ][OK][Data][x]15. PIP Size (Command2:o)GTo select the PIP picture format.You can also select the PIP picture format using WIN.SIZEon the remote control.Transmission[k][o][ ][Set ID][ ][Data][Cr]AcknowledgementData 0: 4:3 1: 16:9[o][ ][Set ID][ ][OK][Data][x]09. Color (Command2:i)GTo adjust the screen color.You can also adjust color in the Video menu.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping1’. See page 27.[k][i][ ][Set ID][ ][Data][Cr]Acknowledgement[i][ ][Set ID][ ][OK][Data][x]10. Tint (Command2:j)GTo adjust the screen tint.You can also adjust tint in the Video menu.TransmissionData Red : 0 ~ Green : 64•Refer to ‘Real data mapping1’. See page 27.[k][j][ ][Set ID][ ][Data][Cr]Acknowledgement[j][ ][Set ID][ ][OK][Data][x]08. Brightness (Command2:h)GTo adjust screen brightness.You can also adjust brightness in the Video menu.TransmissionData Min : 0 ~ Max : 64•Refer to ‘Real data mapping1’. See page 27.[k][h][ ][Set ID][ ][Data][Cr]Acknowledgement[h][ ][Set ID][ ][OK][Data][x]16. Split Zoom (Command2:p)GTo operate split zoom function and select the splitzoom section number.TransmissionData Min: 21 ~ Max:99ex. Data 21: Selection 1 of 2 split zoom.•Refer to ‘Real data mapping 2’.[k][p][ ][Set ID][ ][Data][Cr]Acknowledgement[p][ ][Set ID][ ][OK][Data][x]* Real data mapping 221: Selection 1 of 2 split zoom24: Selection 4 of 2 split zoom41: Selection 1 of 4 split zoom45: Selection 5 of 4 split zoom91: Selection 1 of 9 split zoom99: Selection 9 of 9 split zoom
Owner’s Manual 29External Control Device Setup21. Color Temperature (Command2:u)GTo adjust color temperature.You can also adjust ACC in the Video menu.TransmissionData 0: Normal 1: Cool 2: Warm 3: User[k][u][ ][Set ID][ ][Data][Cr]Acknowledgement[u][ ][Set ID][ ][OK][Data][x]18. Treble (Command2:r)GTo adjust treble.You can also adjust treble in the Audio menu.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping1’. See page 28.[k][r][ ][Set ID][ ][Data][Cr]Acknowledgement[r][ ][Set ID][ ][OK][Data][x]17. PIP Position (Command2:q)GTo select sub picture position for PIP. You can also adjust the sub picture position usingWIN.POSITION on the remote control or in the Special menu.TransmissionData 0: Right down on screen1: Left down on screen2: Left up on screen3: Right up on screen[k][q][ ][Set ID][ ][Data][Cr]Acknowledgement[q][ ][Set ID][ ][OK][Data][x]19. Bass (Command2:s)GTo adjust bass.You can also adjust bass in the Audio menu.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping1’. See page 28.[k][s][ ][Set ID][ ][Data][Cr]Acknowledgement[s][ ][Set ID][ ][OK][Data][x]20. Balance (Command2:t)GTo adjust balance.You can also adjust balance in the Audio menu.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping1’. See page 28.[k][t][ ][Set ID][ ][Data][Cr]Acknowledgement[t][ ][Set ID][ ][OK][Data][x]* Real data mapping 30 : -205 : -19A : -185F: -164: 069: +1C3: +19C8: +2022. Red Adjustment (Command2:v)GTo adjust red in color temperature.TransmissionData Min: 0 ~ Max: C8•Refer to ‘Real data mapping 3’. See page 28.[k][v][ ][Set ID][ ][Data][Cr]Acknowledgement[v][ ][Set ID][ ][OK][Data][x]23. Green Adjustment (Command2:w)GTo adjust green in color temperature.TransmissionData Min: 0 ~ Max: C8•Refer to ‘Real data mapping3’. See page 28.[k][w][ ][Set ID][ ][Data][Cr]Acknowledgement[w][ ][Set ID][ ][OK][Data][x]24. Blue Adjustment (Command2:$)GTo adjust blue in color temperature.TransmissionData Min: 0 ~ Max: C8•Refer to ‘Real data mapping 3’. See page 28.[k][$][ ][Set ID][ ][Data][Cr]Acknowledgement[$][ ][Set ID][ ][OK][Data][x]
30 Plasma DisplayExternal Control Device Setup27. ISM Method (Command2:p)GTo avoid having a fixed image remain on screen.TransmissionData 0: Normal1: White wash 2: Orbiter3: Inversion[j][p][ ][Set ID][ ][Data][Cr]Acknowledgement[p][ ][Set ID][ ][OK][Data][x]28. Low power (Command2:q)GTo control the low power function on/off.TransmissionData 0: Low power off1: Low power on[j][q][ ][Set ID][ ][Data][Cr]Acknowledgement[q][ ][Set ID][ ][OK][Data][x]29. Orbiter Time Setting (Command2:r)GTo adjust orbiter operation time term.TransmissionData Min: 1 ~ Max: FE•Refer to ‘Real data mapping1’. See page 28.[j][r][ ][Set ID][ ][Data][Cr]Acknowledgement[r][ ][Set ID][ ][OK][Data][x]30. Orbiter Pixel Setting (Command2:s)GTo adjust pixel number in orbiter function.TransmissionData Min: 0 ~ Max: 9•Refer to ‘Real data mapping1’. See page 28.[j][s][ ][Set ID][ ][Data][Cr]Acknowledgement[s][ ][Set ID][ ][OK][Data][x]32. Auto configure (Command2:u)GTo adjust picture position and minimize image shakingautomatically. It works only in RGB-PC mode.TransmissionData 1: To set[j][u][ ][Set ID][ ][Data][Cr]Acknowledgement[u][ ][Set ID][ ][OK][Data][x]31. Picture Size Setting for Twin Picture mode(Command2:t)GTo adjust main picture size in twin picture mode.TransmissionData Min: 0 ~ Max: 64•Refer to ‘Real data mapping1’. See page 28.[j][t][ ][Set ID][ ][Data][Cr]Acknowledgement[t][ ][Set ID][ ][OK][Data][x]25. PIP Input Select (Command2:y)G To select input source for sub picture in PIP mode.TransmissionData 0: RGB 1: COMPONENT2: Video 3: S-video 4: DVI[k][y][ ][Set ID][ ][Data][Cr]Acknowledgement[y][ ][Set ID][ ][OK][Data][x]26. Abnormal State (Command2:z)GTo recognize an abnormal state.TransmissionData 0: Normal (Power on and signal exist)1: No signal (Power on)2: Turn the monitor off by remote control3: Turn the monitor off by sleep time function4: Turn the monitor off by RS-232C function5: 5V down6: AC down7: Turn the monitor off by Fan Alarm function8: Turn the monitor off by off time function9: Turn the monitor off by auto off functiona: Turn the monitor off by AV board detect* This function is “read only”.[k][z][ ][Set ID][ ][FF][Cr]Acknowledgement[z][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 31IR CodeG Connect your wired remote control to the Remote port on the Monitor. G Output waveformSingle pulse, modulated with 37.917KHz signal at 455KHzG Configuration of frameG Repeat codeG Lead code• 1st frameLow custom codeLeadcode High custom code Data code Data codeTCTfT1C0Carrier frequencyFCAR = 1/TC= fOSC/12Duty ratio = T1/TC= 1/3• Repeat frameC1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7Repeat code9 ms 4.5 ms0.55 ms9 ms2.25 msG Bit descriptionG Frame interval : TfThe waveform is transmitted as long as a key is depressed.• Bit “0”Tf TfTf=108ms @455KHz0.56 ms 0.56 ms1.12 ms• Bit “1”2.24 msHow to connectHow to connectRemote Control IR Code (NEC Format)Remote Control IR Code (NEC Format)IR Code (NEC Format)IR Code (NEC Format)
32 Plasma DisplayIR CodeUP (D)DOWN (E)VOL+ (G)VOL- (F)POWER On/Off POWER ONPOWER OFFMUTENumber Key 0Number Key 1Number Key 2Number Key 3Number Key 4Number Key 5Number Key 6Number Key 7Number Key 8Number Key 9AII INPUT SELECTRGB DVIVIDEOS-VIDEOCOMPONENTSLEEPOK (Á)MENUDASPAPCPIPPIP INPUTSWAPPIP ARCTWIN PICTUREZOOM +ZOOM -Window SizeWindow PositionSplit ZoomARCARC (4:3)ARC (16:9)ARC (ZOOM)Auto configure00H01H02H03H08HC4HC5H09H10H11H12H13H14H15H16H17H18H19H0BHD5HC6H5AHD8HBFH0EH44H43H52H4DH60H61H63H64H6BH40H41H69H6AH7BH79H76H77HAFH99HR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C Button (Power On/Off)Discrete IR Code (Only Power On)Discrete IR Code (Only Power Off)R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonDiscrete IR Code (Input RGB Selection)Discrete IR Code (Input DVI Selection)Discrete IR Code (Input Video Selection)Discrete IR Code (Input S-video Selection)Discrete IR Code (Input COMPONENT Selection)R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C Button (PIP/TWIN Exchange)R/C Button (4:3/16:9)R/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C ButtonR/C Button(4:3/16:9/Horizon/Zoom Mode Selection)Discrete IR Code (Only 4:3 mode)Discrete IR Code (Only 16:9 mode)Discrete IR Code (Only ZOOM mode)Discrete IR Code (Only RGB-PC mode)Code (Hexa) Function Note
Owner’s Manual 33Troubleshooting ChecklistNo output from one ofthe speakers •Adjust Balance in the AUDIO menu. (Refer to p.17)Unusual sound frominside the monitor•A change in ambient humidity or temperature may result in an unusual noiseat the time of switching off or on of the monitor and does not indicate a faultwith the monitor.No picture &No sound•Check whether the Monitor is turned on.•Power cord inserted into wall outlet?•Test the wall power outlet, plug other product’s power cord into the wall outletwhere the Monitor’s power cord was plugged in.No or Poor coloror Poor picture•Select Color in the VIDEO menu and press the VOLUME (G) button. (Refer to p.16)•Keep a certain distance between the Monitor and the VCR.•Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen gets dark.) The remote control doesn’t work•Check to see if there is any object between the Plasma Display and theremote control causing obstruction.•Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.8) •Install new batteries. (Refer to p.8)Picture OK &No sound•Press the VOLUME (G) button.•Sound muted? Press MUTE button.Picture appears slowly,after switching on•This is normal as the image is muted during the startup process of the moni-tor. Please contact your service centre,if the picture has not appeared afterfive minutes.Horizontal/vertical barsor picture shaking •Check for local interference such as an electrical appliance or power tool.TTroubleshooting Checklistroubleshooting Checklist
34 Plasma DisplayMaintenance1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water anda little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe thescreen.2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Monitor.To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth.Please be sure not to use a wet cloth.If you leave your Monitor dormant for a long time (such as a vacation), it’s a good idea to unplug thepower cord to protect against possible damage from lightning or power surges.- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have yournew Monitor. Be sure to turn the power off and unplug the power cord before you begin any cleaning.Cleaning the ScreenCleaning the ScreenCleaning the CabinetCleaning the CabinetExtended Extended AbsenceAbsenceMaintenanceMaintenance
Owner’s Manual 35Specification•The specifications shown above may be changed without notice for quality improvement.MODELWidth (inches / mm)Height (inches / mm)Depth (inches / mm)Weight (pounds / kg)Power requirementResolutionColorOperating Temperature RangeOperating Humidity RangeMaximum ElevationMU-60PZ90M/90MA/90MB/90MK/90MR/90MSMU-60PZ90V/90VA/90VB/90VK/90VR/90VS 57.3 / 144534.7 / 8833.9 / 99143.9 / 65.3AC120V, 60Hz1280 x 1024 (Dot)16,770,000 (256 steps of each R, G and B)32 ~ 104°F (0 ~ 40°C)Less than 80%6561 feet (2000m)Product SpecificationsProduct Specifications
PLASMA MONITOROWNER’S MANUALPlease read this owner’s manual carefully before operating theMonitor.Retain it for future reference.Record model number and serial number of the Monitor.See the label attached on the back of the Monitor and quotethis information to your dealer when you require service.Model number : Serial number : MODELS:MU-60PZ90M/90VMU-60PZ90MA/90VAMU-60PZ90MB/90VBMU-60PZ90MK/90VKMU-60PZ90MR/90VRMU-60PZ90MS/90VS

Navigation menu