LG Electronics USA RU42PZ61 PDP Display User Manual 470Pen
LG Electronics USA PDP Display 470Pen
Users Manual
PLASMA TV OWNER’S MANUAL MODELS: RU-42PZ61/71 RU-50PZ61 RU-60PZ61 Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service. Model Number : Serial Number : LG Electronics U.S.A., Inc. Warning Warning WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product. COMPLIANCE: The responsible party for this product’s compliance is: Zenith Electronics Corporation 1-201-816-2000 Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 http://www.zenith.com 2 Plasma TV Safety Instructions Safety Instructions Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. 1. Read Instructions All the safety and operating instructions should be read before the product is operated. 9. Attachments Do not use attachments not recommended by the product manufacturer as they may cause hazards. 2. Follow Instructions All operating and use instructions should be followed. 10. Ventilation Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 7. Accessories, Carts, and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Power-Cord Polarization This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. PORTABLE CART WARNING Owner’s Manual 3 Safety Instructions Safety Instructions continued 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions Ground Clamp Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Electric Service Equipment Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC - National Electrical Code 15. Lightning For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 4 Plasma TV 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. 21. Replacement Parts When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Introduction Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .23 Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .24 Special Menu Features Key Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 ISM (Image Sticking Minimization) Method . . . .25 Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Closed Captions . . . . . . . . . . . . . . . . . . . . . . . .27 Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Caption/Text . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Screen Menu Features Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . .28 Setting Picture Format . . . . . . . . . . . . . . . . . . .28 Screen Position . . . . . . . . . . . . . . . . . . . . . . . .28 Manual Configure . . . . . . . . . . . . . . . . . . . . . . .29 Setting VGA Mode . . . . . . . . . . . . . . . . . . . . . .29 Screen Adjustments . . . . . . . . . . . . . . . . . . . . .29 Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . .29 Luminance Noise Reduction . . . . . . . . . . . . . . .30 Initializing (Reset to original factory value) . . . . .30 Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Lock Menu Options Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .31 PIP (Picture-In-Picture)/Double Window Feature Watching PIP/Double Window . . . . . . . . . . . . ..32 Swapping the PIP/Double Window . . . . . . . . . .32 TV Program selection for PIP . . . . . . . . . . . . . .32 Selecting an Input Signal Source for PIP/Double Window .32 Moving the PIP . . . . . . . . . . . . . . . . . . . . . . . . .32 PIP Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 PIP Transparency . . . . . . . . . . . . . . . . . . . . . . .32 Introduction Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Connection Options . . . . . . . . . . . . . . . . . . . . . .8 Remote Control Key Functions . . . . . . . . . . . . . .9 Installation Installation Instruction . . . . . . . . . . . . . . . . . . . . . .10 Attaching the TV assembly to the wall . . . . . . . .10 External Equipment Connections . . . . . . . . . . . . .11 Antenna Connection . . . . . . . . . . . . . . . . . . . . .11 VCR Setup / Cable TV Setup . . . . . . . . . . . . . .12 External A/V Source Setup . . . . . . . . . . . . . . . .13 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 DTV Setup / Monitor Out Setup . . . . . . . . . . . . .14 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Operation Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .16 Menu Language Selection . . . . . . . . . . . . . . . . . .16 Channel Menu Options Auto Program: Channel Search . . . . . . . . . . . . .17 Manual Program: Adding/Deleting Channels . . .17 Fine Tuning Adjustment . . . . . . . . . . . . . . . . . .17 Signal Reception Booster . . . . . . . . . . . . . . . . .18 Favorite Channels Setup . . . . . . . . . . . . . . . . . .18 Picture Menu Options APC (Auto Picture Control) . . . . . . . . . . . . . . . .19 IIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Color Temperature Control . . . . . . . . . . . . . . . .19 Fleshtone . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 sRGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Manual Picture Control (Off option) . . . . . . . . . .20 Sound Menu Options DASP (Digital Auto Sound Processing) . . . . . . .21 BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . .21 Manual Sound Control (Off option) . . . . . . . . . .22 Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .22 Timer Menu Options Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .23 Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .23 External Control Device Setup . . . . . . . . . . . . . . . .33~38 IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39~40 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .41 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .42 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43~44 Setup and Operation Checklist Setup and Operation Checklist (See pages 11~15 for available connection and operational setup options.) 1. Unpack TV and all accessories. 5. Turn video source equipment on. 2. Connect all external video and audio equipment. see pages 12 ~ 14. 6. Select viewing source for TV. See page 9. 3 Install batteries in remote control. See page 9. 7. Fine-tune source image and sound to your personal preference or as required by source. See pages 19 ~ 22. 4. Turn TV on. See page 16. 8. Additional features set up See Contents above. Owner’s Manual 5 Introduction Introduction What is a Plasma Display Panel (PDP)? A plasma display panel is the latest display technology. It is currently the best way to achieve flat panel displays with excellent image quality and large screen sizes, that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps. How does it work? PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors. You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5 inches thick. 160° - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen. Wide Screen The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit. The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product. In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned. 6 Plasma TV Introduction Controls - This is a simplified representation of front panel. Here shown may be somewhat different from your TV. - This manual explains the features available on the RU-42PZ61/71. Front Panel Controls A/V INPUT 2 S-VIDEO VIDEO L/MONO AUDIO R ON/OFF TV/VIDEO MENU VOL CH TV/VIDEO MENU VOL CH A/V INPUT 2 ON/OFF S-VIDEO VIDEO L/MONO AUDIO R 1. S-VIDEO Input A connection available to provide better picture quality than the video input. 5. Power Standby Indicator Illuminates red in standby mode, Illuminates green when the TV is turned on. 2. VIDEO Input 6. Remote Control Sensor Connects the video signal from a video device. 7. TV/VIDEO or ENTER Button 3. AUDIO Input Use to connect to hear stereo sound from an external device. 8. MENU Button 4. ON/OFF Button 9. VOLUME (F,G) Buttons 10. CHANNEL (E, D) Buttons Owner’s Manual 7 Introduction Connection Options Monitor Output Connect a second TV or Monitor. S-Video Input Connect S-Video out from an S-VIDEO device to the S-VIDEO input. DVD/DTV Input (Component 1-2) Remote Control Port Connect a component video/audio device Connect your wired remote to these jacks. control here. AUDIO INPUT Antenna VIDEO INPUT R AUDIO L COMPONENT 2 RGB INPUT AUDIO INPUT DVI INPUT COMPONENT 1 DVD /DTV INPUT VIDEO MONITOR OUTPUT A/V INPUT1 RS-232C INPUT REMOTE (CONTROL/SERVICE) CONTROL (MONO) EXTERNAL SPEAKER AC INPUT S-VIDEO Antenna Inputs Connect cable or antenna signals to the TV, either directly or through your cable box. Audio/Video Input 1 Connect audio/video output from an external device to these jacks. RGB Input/Audio Input/DVI Input Connect the monitor output connector from a PC to the appropriate input port. 8 Plasma TV External Speaker (8 ohm Output) Connect to optional external speaker(s). * For further information, refer to ‘Speaker & Speaker Stand’ manual. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the TV. MODE Selects the remote operating mode: TV, VCR, DVD, CABLE, STB or AUDIO. Select other operating modes, for the remote to operate external devices. TV/VIDEO Selects: TV, Video1-2, Component 1-2, RGB, and DVI input sources. MULTIMEDIA Selects: Component 1-2, RGB, and DVI input sources. ARC Changes the aspect ratio. TV/VIDE MODE MED MULTI POWER ARC IA MUTE MUTE Switches the sound on or off. NUMBER buttons FCR Use to scroll the Surf channel list. APC Adjusts the factory preset picture according to the room. VOLUME UP/DOWN Increases/decreases the sound level. REVIEW Tunes to the last channel viewed. FCR REVIEW APC DASP VOL CH PIP/DW CAPTION MENU EXIT PIP INPUT PIP CH- PLAY PAUSE STOP RECORD REW FF SKIP PIP ARC PIPCH-/PIPCH+ Changes to next lower/higher PIP channel. PIP ARC Changes the PIP picture format. CHANNEL UP/DOWN Selects available channels found with Auto program. EXIT Clears all on-screen displays and returns to TV viewing from any menu. ENTER PIP CH+ SWAP THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference. DASP Selects the sound appropriate for the program's character. CAPTION Selects CAPTION mode. MENU Brings up the main menu to the screen. PIP/DW Switches between PIP, and Double Window modes. POWER Turns your TV or any other programmed equipment on or off, depending on mode. WIN.SIZE WIN.POSITION SLEEP MEMORY/ERASE A.PROG SPLIT ZOOM MTS ZOOM- ZOOM+ WIN. SIZE Adjusts the sub picture size. MEMORY/ERASE Memorizes or erases selected channel. A.PROG (AUTO PROGRAM) Searches for available channels. SPLIT ZOOM Enlarges the picture. PIP INPUT Selects the input source for the sub picture. SWAP Exchanges the PIP/main images. VCR/DVD BUTTONS Control some video cassette recorders or DVD player ("RECORD" button is not available for DVD player). SLEEP Sets the sleep timer. MTS Selects the MTS sound: Mono, Stereo, or SAP. WIN.POSITION Moves the sub picture. ZOOM-/ZOOM+ Enlarges or reduces the main picture size. Installing Batteries • Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). • Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones. Replace cover. Owner’s Manual 9 Installation Installation Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. MU TE TV /VI DE CA PT IO MU LTIM PO ER EDI AR MT ME NU CH VO EN CH TE VO 1.5V 1.5V SP WI PO SIT N.S SW Owner’s Manual Power Cord Batteries ZO OM RE PIP /DW PIP CH CH A.P - PIP AP RO AP LIT IZE PIP ION MEM ORY /ER ASE FC VIE DA SP SL EE INP UT Remote Control DVI Cable D-sub 15 pin cable 2-TV bracket bolts 2-TV brackets 2-Wall brackets Installation Instructions GROUNDING Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Power Supply Short-circuit Breaker Attaching the TV assembly to the wall - Secure the TV assembly by attaching it to a wall for additional support. • Install the TV brackets on the TV as shown. Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the product), as shown. Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely. • Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown. 10 Plasma TV Installation External Equipment Connections Antenna Connection - Antenna or Cable Service without a Cable Box Connections - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) wall antenna socket MONITOR OUTPUT Bronze Wire A/V INPUT 1 L/MONO AUDIO RF coaxial wire (75 ohm) S-VIDEO Antenna VIDEO Turn clockwise to tighten. VHF antenna UHF antenna Bronze Wire outdoor antenna Be careful not to bend the bronze wire when connecting the antenna. Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) • To improve picture quality in a poor signal area, purchase and install a signal amplifier. • If the antenna needs to be split for two TV’s, install a “2-Way Signal Splitter” in the connections. Antenna Signal Amplifier • If the antenna is not installed properly, contact your dealer for assistance. Owner’s Manual 11 Installation NOTE: All cables shown are not included with the TV VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV - Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) 3. Select the input source by the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source) COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT 1 VIDEO AUDIO AUDIO Antenna S-VIDEO AC INPUT L/MONO VIDEO ANT IN S-VIDEO ANT OUT VCR OUT OUTPUT SWITCH IN (R) AUDIO (L) VIDEO Do not connect to both Video and SVideo at the same time. In the event that you connect both Video and the S-Video cables, only the S-Video will work.) Cable TV Setup - After subscribing to a cable TV service from a local provider you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV. - For further information regarding cable TV service, contact your local cable TV service provider(s). Connection Option 1 1. Select 3 or 4 with channel switch on cable box. 2. Tune the TV channel to the same selected output channel on cable box. 3. Select channels at the cable box or with the cable box remote control. COMPONENT INPUT 2 Connection Option 2 1. Connect the audio and video cables from the Cable Box's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). 2. Select the input source by using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source) 3. Select your desired channel with the remote control for cable box. MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT 1 VIDEO S-VIDEO Antenna VIDEO (R) AUDIO (L) TV VIDEO OUTPUT SWITCH VCR RF Cable Box 12 Plasma TV AC INPUT L/MONO AUDIO AUDIO Cable Installation External A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT 1 VIDEO AUDIO AUDIO S-VIDEO Antenna AC INPUT L/MONO VIDEO How to use 1. Select the input source by using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source). 2. Operate the corresponding external equipment. Refer to external equipment operating guide. Camcorder AUDIO VIDEO Video Game Set DVD Setup How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. NOTE: If your DVD player does not have component video output, use S-Video. COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT 1 VIDEO AUDIO S-VIDEO Antenna AC INPUT L/MONO AUDIO VIDEO How to use 1. Turn on the DVD player, insert a DVD. 2. Use the TV/VIDEO or MULTIMEDIA button on the remote control to select Component 1 or Component 2. (If connected to SVIDEO, select the Video 1 or Video 2 external input source.) 3. Refer to the DVD player's manual for operating instructions. • Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV PB Video output ports on DVD player Pr Pb B-Y R-Y Cb Cr PB PR PR or (R) AUDIO (L) S-VIDEO (R) AUDIO (L) DVD Owner’s Manual 13 Installation DTV Setup - To watch digitally broadcast programs, purchase and connect a digital set-top box. COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 RS-232C INPUT REMOTE CONTROL DVI INPUT (CONTROL/SERVICE) AUDIO INPUT A/V INPUT 1 RGB INPUT VIDEO AUDIO S-VIDEO L/MONO AUDIO Antenna VIDEO or or (R) AUDIO (L) RGB-DTV OUTPUT DVI-DTV OUTPUT (R) AUDIO (L) (R) AUDIO (L) Digital Set-top Box How to connect Use the TV’s COMPONENT (Y, PB, PR) INPUT jacks, RGB or DVI port for video connections, depending on your set-top box connections available. Then, make the corresponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) 2. Use TV/VIDEO or MULTIMEDIA on the remote control to select Component 1, Component 2, RGB, or DVI source. Signal 480i 480p 720p 1080i Component 1/2 Yes Yes Yes Yes RGB,DVI No Yes Yes Yes Monitor Out Setup The TV has a special signal output capability which allows you to hook up a second TV or monitor. COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT 1 VIDEO S-VIDEO Antenna AC INPUT L/MONO AUDIO AUDIO Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings. VIDEO NOTE • Component, RGB, DVI input sources cannot be used for Monitor out. S-VIDEO IN (R) AUDIO (L) 14 Plasma TV VIDEO Operation PC Setup How to connect 1. To get the best picture quality, adjust the PC graphics card to 640x 480, 60Hz. 2. Use the TV’s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector. • If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the TV. • If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.) 3. Then, make the corresponding audio connection. If using a sound card, adjust the PC sound as required. REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT AUDIO INPUT RGB INPUT How to use 1. Turn on the PC and the TV. 2. Turn on the display by pressing the POWER button on the TV's remote control. 3. Use TV/VIDEO or MULTIMEDIA on the remote control to select RGB, or DVI source. 4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. NOTES: • Use a DVI cable. • Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible. • The synchronization input form for Horizontal and Vertical frequencies is separate. Monitor Display Specifications (RGB / DVI Mode) Resolution 640x350 720x400 640x480 848x480 852x480 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.468 70.09 37.861 85.08 31.469 70.08 37.927 85.03 31.469 59.94 35.000 66.66 37.861 Resolution Horizontal Vertical Frequency(KHz) Frequency(Hz) 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 49.725 74.55 72.80 48.363 60.00 37.500 75.00 56.476 70.06 43.269 85.00 60.023 75.02 31.500 60.00 68.677 85.00 37.799 70.00 54.348 60.05 39.375 75.00 63.995 70.01 31.500 60.00 67.500 75.00 37.799 70.00 77.487 85.00 39.375 75.00 1152x870 68.681 75.06 1280x960 60.023 60.02 1280x1024 63.981 60.02 800x600 832x624 1024x768 1152x864 RGB Mode Only Owner’s Manual 15 Operation Operation Turning the TV On * In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just an example to help you with the TV operation. Turning on the TV just after installation 1. Connect power cord correctly. 2. Press the ON/OFF button on the TV. At this moment, the TV is switched to standby mode. Press the TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO, MULTIMEDIA, Number (0 ~ 9) button on the remote control and then the TV will turn on. Turning on the TV (power cord is still connected) 1. If the TV was turned off with the • Press the ON/OFF button on the TV ON/OFF button on the TV to turn the TV on. 2. If the TV was turned off with the remote control and then the ON/OFF button on the TV • Press the ON/OFF button on the TV and then press the TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO, MULTIMEDIA, Number (0 ~ 9) button on the remote control to turn the TV on. NOTE • If you intend to be away on vacation, disconnect the power plug from the wall power outlet. Menu Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use 2. Press the G button and then use D / button to select the SPECIAL menu. button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the language of your choice. 4. Press the ENTER button to save. 16 Plasma TV Operation Channel Menu Options Auto Program should be used to memorize all the active channels in your area before you are able to use the TV. There are two ways of storing channels in the TV's memory. You can use either. One is called AUTO PROGRAM and the other is called MANUAL PROGRAM. In AUTO PROGRAM mode, the TV will memorize the channels in ascending numerical order. If there are additional channels you want to add or delete, you can manually add or delete those channels with Manual Program. Auto Program: Channel Search - Redo Auto Program if the Plasma Display is ever moved to another location. - Auto Program will search for channels only through the ANT IN jack. - If channels numbers for broadcast over-the air TV and cable TV are duplicated where different channels have the same number, press the same number buttons again to toggle between: Cable TV Channels Broadcast TV Channels CHANNEL Auto program To start Manual program PICTURE Favorite channel SOUND TIMER SPECIAL (For example, press 17 to go to the channel, press 17 again to go to the duplicated channel.) 1. Press the A.PROG button and then press the G button. AUTO PROGRAM starts the channel search. If you want to stop auto programming, press the ENTER button. Only the channels found up to at that time are memorized. • You can also select the Auto program option and do a channel search in the CHANNEL menu. SCREEN PIP/DW LOCK Menu Prev. Manual Program: Adding/Deleting Channels - You can add or delete channels from the channel scan manually. 1. Use the D /E or NUMBER buttons to select the channel number you want to add or delete. 2. Press the MEMORY/ERASE button. 3. Use the MEMORY/ERASE button to select Memory or Erase. 4. Press the ENTER button. • You can also do Manual program with the CHANNEL menu. Fine Tuning Adjustment - Use this function to correct the picture's instability and condition if it is poor. 1. Press the MENU button and then use D /E button to select the CHANNEL menu. CHANNEL Auto program Manual program PICTURE 2. Press the G button and then use D /E button to select Manual program. SOUND 3. Press the G button and then use D /E button to select Fine. TIMER Favorite channel TV Memory Fine Booster 4. Use the F /G button to adjust the picture to your preference. 5. Press the ENTER button to save. On Off SPECIAL SCREEN PIP/DW Notes • To remove fine tuning from a channel, reprogram the finely-tuned channel with Auto program or Manual Program. • If a finely-tuned channel is memorized, the color of the channel number changes to yellow. LOCK Menu Prev. Owner’s Manual 17 Operation Channel Menu Options continued Signal Reception Booster - If TV signal reception is poor because you are in a fringe area, set Booster to On. If the picture condition is good, set Booster to Off. - Adjustments for one channel don’t affect the adjustment for other channels. Set booster to on or off for each channel separately. 1. Press the MENU button and then use D /E button to select the CHANNEL menu. CHANNEL 2. Press the G button and then use D /E button to select Manual program. Manual program PICTURE 3. Press the G button and then use 4. Use F /G D /E button to select Booster. Auto program TV Memory Favorite channel On Fine SOUND button to select On or Off. Booster Off TIMER 5. Press the ENTER button to save. SPECIAL SCREEN PIP/DW LOCK Menu Prev. Favorite Channels Setup - Favorite Channels is a convenient feature that lets you quickly scan up to 8 channels of your choice without having to wait for the TV to scan through all the in-between channels. 1. Press the MENU button and then use D /E button to select the CHANNEL menu. 2. Press the G button and then use D /E button to select Favorite channel. 3. Press the G button and then use position. D /E button to select the first favorite channel 4. Use the F / G button to set the desired channel number for first favorite channel. 5. Repeat steps 3 to 4 to memorize other favorite channels. 6. Press the ENTER button to save. • To tune to a favorite channel, press the FCR (Favorite Channel Review) button repeatedly. The eight favorite channels appear on the screen in numerical order. 18 Plasma TV CHANNEL Auto program Manual program PICTURE Favorite channel SOUND TIMER SPECIAL SCREEN PIP/DW LOCK Menu Prev. ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- Operation Picture Menu Options APC (Auto Picture Control) - APC adjusts the TV to the best picture appearance. - If adjusting picture options (contrast, brightness, color, sharpness, or tint) manually, APC automatically changes to Off. 1. Press the APC button repeatedly to select the picture appearance setup option as shown below. Daylight Optimum Night time Off • You can also adjust APC in the PICTURE menu. • Daylight, Optimum, and Night time settings are preset for good picture quality at the factory and cannot be changed. IIP - Improves picture outline in dark areas. CHANNEL APC SOUND 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select IIP. 3. Press the button and then use D /E D /E button to select the PICTURE menu. button to set On or Off. 4. Press the ENTER button to save. Off ACC Fleshtone Contrast TIMER SPECIAL SCREEN On IIP PICTURE 100 Brightness 55 Color 55 Sharpness 60 Tint PIP/DW LOCK Menu Prev. Color Temperature Control Auto Color Temperature Control CHANNEL - To initialize values (reset to default settings), select the Normal option. 1. Press the MENU button and then use D 2. Press the button and then use D /E /E button to select the PICTURE menu. APC IIP PICTURE SOUND ACC Contrast button to select ACC . 3. Press the G button and then use D / E button to select either: Cool (Preset), Normal (Default), or Warm (Preset). 4. Press the ENTER button to save. TIMER SPECIAL SCREEN Cool Normal Fleshtone 100 Warm Brightness 55 Off Color 55 Red Sharpness 60 Green Blue Tint PIP/DW LOCK Menu Prev. Manual Color Temperature Control (ACC set to Off option) - You can adjust red, green, or blue to any color temperature you prefer. 1. Press the MENU button and then use D /E button to select the PICTURE menu. 2. Press the button and then use 3. Press the button and then use D /E button to select Off. 4. Press the button and then use D /E button to select Red, Green or Blue. 5. Use the F /G D /E button to select ACC . button to make appropriate adjustments. • The adjustment range of Red, Green, and Blue is -30 ~ +30. 6. Press the ENTER button to save. Owner’s Manual 19 Operation Picture Menu Options continued Fleshtone (TV, (TV, Video1-2, Video1-2, Component 1-2, RGB-DTV, RGB-DTV, and DVI-DTV Mode only) - Use Fleshtone to select the desired skin color option. 1. Press the MENU button and then use D /E 2. Press the G button and then use button to select Fleshtone. D /E 3. Press the G button and then use F /G button to select the PICTURE menu. button to make appropriate adjustments. CHANNEL APC IIP PICTURE SOUND ACC Contrast • The adjustment range is 0 ~ 3. TIMER 4. Press the ENTER button to save. SPECIAL SCREEN Fleshtone Brightness 55 Color 55 Sharpness 60 Tint 100 PIP/DW LOCK Menu Prev. sRGB (only RGB-PC, DVI-PC Modes) - If the TV is connected to external equipment using sRGB, set sRGB to On to adjust for the color difference. CHANNEL APC IIP PICTURE 1. Press the MENU button and then use D /E button to select the PICTURE menu. SOUND 2. Press the G button and then use 3. Press the button and then use button to select sRGB. D /E D /E button to select On or Off. ACC sRGB Contrast TIMER SPECIAL On 100 Off Brightness 55 Color 55 4. Press the ENTER button to save. SCREEN PIP/DW LOCK Menu Prev. Manual Picture Control ( APC set to set to Off option) - You can adjust picture contrast, brightness, color, sharpness, and tint options to the levels you prefer. CHANNEL APC IIP PICTURE 1. Press the MENU button and then use D /E button to select the PICTURE menu. SOUND ACC Fleshtone Contrast 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, Tint). 3. Press the G button and then use F /G TIMER SPECIAL button to make appropriate adjustments. SCREEN 4. Press the ENTER button to save. 60 Color 50 Sharpness 50 Tint PIP/DW LOCK 20 Plasma TV 100 Brightness Menu Prev. Operation Sound Menu Options DASP (Digital Auto Sound Processing) - This function lets you enjoy the best sound without any special adjustment because the TV has the appropriate sound options based on the program content. - If you adjust sound options (Treble and Bass) manually, DASP automatically changes to Off. 1. Press the DASP button repeatedly to select the appropriate sound setup as shown below. SRS TSXT Flat Music Movie Sports Off • You can also adjust DASP in the SOUND menu. • SRS TSXT, Flat, Music, Movie, and Sports are preset for good sound quality at the factory and cannot be changed. • is a trademark of SRS Labs, Inc. • TruSurround XT technology is incorporated under license from SRS Labs, Inc. BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility and music realism. CHANNEL 1. Press the MENU button and then use D /E button to select the SOUND menu. 2. Press the button and then use D /E button to select BBE. SOUND 3. Press the button and then use D /E button to select On or Off. TIMER 4. Press the ENTER button to save. DASP BBE PICTURE On Off AVL Balance Treble 50 Bass 50 SPECIAL SCREEN • Manufactured under license from BBE Sound, Inc. • Treble, Bass or BBE aren’t suitable for SRS TSXT mode. PIP/DW LOCK Menu CHANNEL DASP Prev. AVL (Auto Volume Volume Leveler) - AVL maintains an equal sound level; even if you change channels. 1. Press the MENU button and then use 2. Press the 3. Press the button and then use button and then use 4. Press the ENTER button to save. D /E D /E D /E button to select the SOUND menu. button to select AVL. button to select On or Off. BBE PICTURE SOUND TIMER AVL Balance Treble 50 Bass 50 On Off SPECIAL SCREEN PIP/DW LOCK Menu Prev. Owner’s Manual 21 Operation Sound Menu Options continued Manual Sound Control ( DASP off option and balance) - You can adjust sound options Balance, Treble, and Bass to the levels you prefer. CHANNEL 1. Press the MENU button and then use D 2. Press the G button and then use D (Balance, Treble, Bass). /E 3. Press the G button and then use F /G /E button to select the SOUND menu. button to select the desired sound option BBE PICTURE SOUND TIMER button to make appropriate adjustments. 4. Press the ENTER button to save. DASP AVL Balance Treble 50 Bass 50 SPECIAL SCREEN PIP/DW LOCK Menu Prev. Stereo/SAP Broadcasts Setup - The TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the broadcaster transmits one additional sound signal in addition to the original one. - Mono: The primary language is heard from left and right speakers. Signal mode is mono. - Stereo: The primary language is heard from left and right speakers. Signal mode is stereo. - SAP: The secondary language is heard from left and right speakers in mono sound. 1. Press the MTS button repeatedly. Mono Stereo SAP • Select mono sound mode if the signal is not clear or in poor signal reception areas. • Stereo, SAP modes are available only if included on the broadcast signal. 22 Plasma TV Operation T imer Menu Options Auto Clock Setup - Set the time automatically through the PBS broadcast signal. - ThePBS channel signal includes information for the current time. - Set the clock manually, if the current time is set incorrectly programed by the auto clock function. 1. Press the MENU button and then use D /E button to select the TIMER menu. CHANNEL 2. Press the button and then use D /E button to select Clock. Clock 3. Press the button and then use D /E button to select Auto. SOUND 4. Press the G button and then use D / E button to select the time zone for your viewing area. Your choices are: Auto, E.S.T. (Eastern Standard Time), C.S.T. (Central Standard Time), M.S.T. (Mountain Standard Time), P.S.T. (Pacific Standard Time), Alaska, and Hawaii. Auto Off timer Manual On timer Time zone PICTURE Auto Auto off PBS Channel TIMER TV 2 Daylight Saving SPECIAL Auto SCREEN 5. Press the button and then use D /E button to set PBS Channel. PIP/DW 6. Press the G button and then use D / E button to set Daylight Saving Time Auto, On or Off, depending on whether or not your viewing area observes Daylight Saving Time. LOCK Menu CHANNEL Clock Prev. 7. Press the ENTER button to save. Manual Clock Setup - If current time setting is wrong, reset the clock manually. 1. Press the MENU button and then use D /E button to select the TIMER menu. button and then use D /E button to select Clock. 3. Press the button and then use D /E button to selectt Manual. 4. Press the button and then use D /E button to set the hour. SPECIAL 5. Press the button and then use D /E button to set the minutes. SCREEN SOUND Auto Manual On timer -- : PICTURE 2. Press the 6. Press the ENTER button to save. Off timer -- AM Auto off TIMER PIP/DW LOCK Menu Prev. On/Off On/Off Timer Setup Timer function operates only if current time has been set. Off-Timer function overrides On-Timer function if they are set both set to the same time. The TV must be in standby mode for the On-Timer to work. If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the TIMER menu. button to select Off timer or On timer. 3. Press the G button and then use D / E button to select On. • To cancel On/Off timer function, select Off. CHANNEL Clock Off timer PICTURE SOUND On timer Auto off button and then use D /E button and then use D /E Off : 30 AM Volume button to set the hour. Ch. SPECIAL 5. Press the On TIMER 4. Press the 17 TV 2 button to set the minutes. SCREEN 6. For only On timer function Press the G button and then use Press the G button and then use D /E D /E button to set the sound level at turn-on. button to select the channel at turn-on. PIP/DW LOCK Menu Prev. 7. Press the ENTER button to save. Owner’s Manual 23 Operation T imer Menu Options continued Sleep Timer - The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. 1. Press the SLEEP button repeatedly to select the number of preset minutes. First the on the screen, followed by the following sleep timer turn off times: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. zz --- Min option appears 2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the TV turns off, press the SLEEP button once. 4. To cancel the Sleep Timer, press the SLEEP button repeatedly until zz --- Min appears. Auto Off Off - If set to on and there is no input signal, the TV turns off automatically after 10 minutes. CHANNEL 1. Press the MENU button and then use D / E button to select the TIMER menu. 2. Press the G button and then use D / E button to select Auto off. Clock Off timer PICTURE SOUND On timer Auto off D /E 4. Press the ENTER button to save. button to select On or Off. SPECIAL SCREEN PIP/DW LOCK 24 Plasma TV On Off TIMER 3. Press the G button and then use Menu Prev. Operation Special Menu Options Key Lock - The TV can be set up so that it can only be used with the remote control. - This feature can be used to prevent unauthorized viewing by locking out the front panel controls. - This TV is programmed to remember which option it was last set to even if you turn the TV off. CHANNEL Language Key lock PICTURE SOUND On Off ISM Method Low power Set ID 1. Press the MENU button and then use D /E button to select the SPECIAL menu. 2. Press the button and then use D /E button to select Key lock. 3. Press the button and then use D /E button to select On or Off. TIMER SPECIAL Caption / Text Captions SCREEN PIP/DW 4. Press the ENTER button to save. • With the Key lock On, the display ‘ W Key lock’ appears on the screen if any button on the front panel is pressed. LOCK Menu Prev. ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in a ghost image remaining even when you change the image. Avoid allowing a fixed image to remain on the TV's screen for a long period of time. 1. Press the MENU button and then use D /E button to select the SPECIAL menu. CHANNEL 2. Press the button and then use D /E button to select ISM Method. 3. Press the G button and then use wash, Orbiter or Inversion. D /E button to select either Normal, White Key lock PICTURE • Normal If image sticking is never a problem, ISM is not necessary - set to Normal. • White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press any button. • Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move every 2 minutes: Right → Right → Downside → Downside → Left → Left → Upside → Upside. • Inversion Inversion will automatically invert the TV panel color every 30 minutes. Language SOUND TIMER SPECIAL ISM Method Normal Low power White wash Set ID Orbiter Caption / Text Inversion Captions SCREEN PIP/DW LOCK Menu Prev. 4. Press the ENTER button to save. Owner’s Manual 25 Operation Special Menu Options continued Low Power - Low power reduces the plasma display power consumption. 1. Press the MENU button and then use D 2. Press the /E button to select the SPECIAL menu. CHANNEL button and then use D /E button to select Low power. 3. Press the button and then use D /E button to select On or Off. SOUND • When you select On, the screen darkens. 4. Press the ENTER button to save. Language Key lock PICTURE ISM Method Low power TIMER SPECIAL Caption / Text Captions SCREEN PIP/DW LOCK 26 Plasma TV Menu On Off Set ID Prev. Operation Closed Captions Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs. 1. Poor reception conditions are encountered: • IGNITION: Picture may flutter, drift, suffer from black spots, or horizontal streaking. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances. Using Closed Captions Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance. Its possible to caption a live program by using a process called real-time captioning, which creates captions instantly. Real-time captioning is normally done by professional reporters using a machine shorthand system and computer for translation into English. Captioning is an effective system for the hearing-impaired, and it can also aid in teaching language skills. FOLLOW ME • GHOSTS: Ghosts are caused when the TV signal splits and follows two paths. One is the direct path and the other is reflected off tall buildings, hills or other objects. Changing the direction or position of the antenna may improve reception. • SNOW: If your receiver is located at the weak, fringe area of a TV signal, your picture may be marred by small dots. It may be necessary to install a special antenna to improve the picture. • The picture at left shows a typical caption. Caption Tips • Not all TV broadcasts include closed caption signals. • Sometimes TV stations broadcast four different caption signals on the same channel. By selecting CC 1 to CC 2, you can choose which signal you view. CC 1 is usually the signal with the captions, while Another mode might show demonstration or programming information. • Your TV might not receive caption signals normally in the following situations. 2. An old, bad, or illegally recorded tape is being played. 3. Strong, random signals from a car or airplane interfere with the TV signal. 4. The signal from the antenna is weak. 5. The program wasn’t captioned when it was produced, transmitted, or taped. Captions 1. Use the CAPTION button repeatedly to select Caption Off, EZ Mute, or On. • EZ Mute shows the selected captions option (if available on program) when the TV sound is muted 2. Press the ENTER button to save. Caption/Text Caption/Text 1. Press the MENU button and then use D / E button to select the SPECIAL menu. 2. Press the G button and then use D / E button to select Caption / Text. CHANNEL PICTURE 3. Press the G button and then use D / E button to select caption: CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. • CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. • TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. SOUND Language Key lock CC1 ISM Method CC2 Low power CC3 CC4 Set ID TIMER SPECIAL Caption / Text Captions Text1 Text2 Text3 Text4 SCREEN PIP/DW LOCK Menu Prev. 4. Press the ENTER button to save. Owner’s Manual 27 Operation Screen Menu Options Auto Adjustment RGB (PC) mode only; This function doesn’t work for RGB-DTV mode. Automatically adjusts picture position and minimizes image shaking. After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. The Auto config. and Manual config. are not active in DVI mode. 1. Press the MENU button and then use D /E button to select the SCREEN menu. CHANNEL 2. Press the G button and then use D /E button to select Auto config.. Auto config. To set ARC PICTURE Position 3. Press the G button to run Auto configure. SOUND • When Auto config. has finished, OK will be shown on screen. • If the position of the image is still not correct, try Auto adjustment again. 4. In RGB (PC) mode, if the image needs to be adjusted more after using Auto config., you can make further adjustments with the Manual config. option. Manual config Reset TIMER SPECIAL SCREEN PIP/DW LOCK Menu Prev. Setting Picture Format Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible. Set every aspect ratio for TV, Video, Component 480i sources. Use 4:3, or 16:9 for other RGB-PC and DVI-PC sources. Horizon is not available for Component (480p,720p,1080i), DTV (480p,720p,1080i) sources. 1. Press the ARC button repeatedly to select the desired picture format. You can also adjust ARC in the SCREEN menu. • 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. • 16:9 Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. • Horizon Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. • Zoom - Choose Zoom when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. Screen Position - This function works in the following modes: RGB-PC, RGB-DTV (480p,720p,1080i), DVI-DTV (480p,720p,1080i), COMPONENT (480p,720p,1080i). CHANNEL SOUND 1. Press the MENU button and then use D /E button to select the SCREEN menu. 2. Press the button and then use D /E 3. Press the button and then use D /E /F /G 4. Press the ENTER button to save. button to select Position. button to adjust the position. Position Manual config Reset TIMER SPECIAL SCREEN PIP/DW LOCK 28 Plasma TV Auto config. ARC PICTURE Menu Prev. Operation Manual Configure (RGB-PC mode only) - If the image still isn’t clear after auto adjustment and especially if characters are still jittery, adjust the picture Phase manually. - To correct the screen size, adjust Clock. 1. Press the MENU button and then use D /E button to select the SCREEN menu. CHANNEL Auto config. ARC PICTURE SOUND Position Manual config Reset 2. Press the G button and then use D /E button to select Manual config.. 3. Press the G button and then use D /E button to to select Phase or Clock. 4. Use the F /G button to make appropriate adjustments. • The Phase adjustment range is 0 ~ 30. • The Clock adjustment range is -127 ~ +128. Phase Clock TIMER SPECIAL SCREEN PIP/DW LOCK Menu Prev. 5. Press the ENTER button to save. Selecting VGA mode (RGB-PC mode only) CHANNEL - To see a normal picture, match the resolution of RGB mode and selection of VGA mode. ARC PICTURE SOUND 1. Press the MENU button and then use D 2. Press the G button and then use button to select the SCREEN menu. button to select VGA Mode. D /E 3. Press the G button and then use tion. /E D /E button to select the desired VGA resolu- Auto config. Position Manual config Reset TIMER VGA Mode 640x480 848x480 SPECIAL 852x480 SCREEN PIP/DW 4. Press the ENTER button to save. LOCK Menu Prev. Screen Adjustments (TV, (TV, Video1-2 Video1-2 and Component 480i mode only) - Use this function to correct jittering or picture instability while viewing a video tape. CHANNEL Screen adj. 1. Press the MENU button and then use D /E button to select the SCREEN menu. 2. Press the G button and then use D /E button to select Screen adj.. 3. Press the G button and then use D /E button to select TV or VCR. • Select the VCR option if watching a VCR. • Select the TV option for other equipment. (Except VCR) 4. Press the ENTER button to save. TV VCR ARC PICTURE Cinema SOUND YNR Reset TIMER SPECIAL SCREEN PIP/DW LOCK Menu Prev. Cinema Mode Setup (TV, (TV, Video1-2 Video1-2 and Component 480i mode only) - Sets up the TV for the best picture appearance for viewing movies. CHANNEL Screen adj. ARC 1. Press the MENU button and then use D 2. Press the 3. Press the button and then use button and then use 4. Press the ENTER button to save. D /E D /E /E button to select the SPECIAL menu. PICTURE button to select Cinema.. SOUND button to select On or Off. TIMER Cinema On Off YNR Reset SPECIAL SCREEN PIP/DW LOCK Menu Prev. Owner’s Manual 29 Operation Screen Menu Options continued Luminance Noise Reduction (TV, (TV, Video Video 1-2 and Component 480i modes only) - Use YNR to reduce the picture noise that may appear on the screen. Screen adj. CHANNEL ARC 1. Press the MENU button and then use D 2. Press the button and then use /E button to select the SCREEN menu. button to select YNR. D /E PICTURE On Cinema YNR SOUND Off To set Reset 3. Press the G button and then use D /E button to select On or Off. 4. Press the ENTER button to save. TIMER SPECIAL SCREEN PIP/DW LOCK Menu Prev. Initializing (Reset to original factory value) Screen adj. CHANNEL - Use the Reset option to initialize the adjusted settings. ARC PICTURE Cinema YNR SOUND Reset 1. Press the MENU button and then use D 2. Press the G button and then use D /E /E button to select the SCREEN menu. button to select Reset. TIMER SPECIAL SCREEN 3. Press the G button. • You can initialize Position, Split zoom, PIP Transparency, PIP position, PIP size and sub picture size for double window. PIP/DW LOCK Menu Prev. Split Zoom Enlarges the picture in correct proportions. Split Zoom can be used for all input sources. In 2-Split Zoom mode, you can only move the image up or down. If an image is enlarged, a section can be viewed without using Split Zoom. 1. Press the SPLIT ZOOM button repeatedly to select either 2, 4, or 9 Split Zoom. 2-Split zoom 4-Split zoom 9-Split zoom 2. Press the number button corresponding to the section you wish to enlarge. You can move within the enlarged picture using the D / E / F / G button. To return to normal viewing, press the SPLIT ZOOM button again. 9-Split zoom 30 Plasma TV Example of choosing 5. Section 5 is enlarged to fill the screen. Operation Lock Menu Options Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enable the lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only. Ratings for Movies previously shown in theaters: Movie Ratings : • Blocking Off (Permits all programs) • G (General audience) • PG (Parental guidance suggested) • PG-13 (Parents strongly cautioned) • R (Restricted) • NC-17 (No one 17 and under admitted) • X (Adult only) If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked. Ratings for Television programs including made-for-TV movies : General TV Ratings: • Blocking Off • TV-G (general audience) (individual categories do not apply) • TV-PG (parental guidance suggested) • TV-14 (14 years and older) • TV-MA (mature audience) Children TV Ratings: • Blocking Off • TV-Y (youth) (individual content categories do not apply) • TV-Y7 (youth, 7 years and up) Content Categories: • Dialog - sexual dialogue (applies to TV-PG, TV-14) • Language - adult language (applies to TV-PG, TV-14, TV-MA) • Sex scenes - sexual situations (applies to TV-PG, TV-14, TVMA) • Violence (applies to TV-PG, TV-14, TV-MA) • F Violence - fantasy violence (applies only to TV-Y7) Aux. Block • Video 1, 2 (On, Off) • Component 1, 2 (On, Off) • RGB, DVI (On, Off) Parental Lock Setup - Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources. - A password is required to gain access to this menu if the Lock System is turned on 1. Press the MENU button and then use D Then, press the G button /E button to select the LOCK menu. • If Lock is already set, enter the password as requested. • The TV is set up with the initial password “0-0-0-0”. CHANNEL Set password • Lock on/off: Activates or disables the blocking scheme you set up previously. • Set Password: Change the password by inputting a new password twice. • MPAA (Movie Rating): Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. On Off PICTURE MPAA SOUND 2. Use the D / E button to choose from the following Lock Menu options. Once the option is selected, change the settings to your preference. Lock on/off Age block Content block TIMER Aux.block SPECIAL SCREEN PIP/DW LOCK Menu Prev. • TV Rating-Children: Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. • TV Rating-General: Based on the ratings, blocks certain TV programs that you and your family do not want to view. • Aux. Block: Enables you to select a source to block from the external source devices you have hooked up. 3. Press the ENTER button to save. Note • If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control. Owner’s Manual 31 Operation PIP (Picture-In-Picture)/Double W indow Feature - PIP lets you view 2 different inputs pictures (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image. - Double Window mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen. Moving the PIP (PIP Mode only) Watching PIP/Double Window Window Press the PIP/DW button to access the sub picture. Each press of PIP changes the PIP options as shown below. Press the POSITION button. Press the D / E / F / G button repeatedly until desired position is achieved. The sub picture moves up/down/left/right. • You can also move the PIP position with Win.position in the PIP/DW menu. DW 1 PIP Win.position ▲ ◀ ▶ ▼ PIP Size Off DW 2 Swapping the PIP/ PIP/ Double W indow Use the SWAP button to switch the main and sub pictures. Press the WIN.SIZE button and then use change the sub picture size. F / G button to • Using the Win.size function in Double Window mode, main and sub picture sizes are changed simultaneously. Using the Win.size function in PIP mode, sub picture size is changed. • You can also change the sub picture size with Win.size in the PIP/DW menu. Win.size Main Picture Sub Picture PIP Transparency (PIP Mode only) - To make the PIP clear or opaque 1. Press the MENU button and then use select the PIP/DW menu. Main Picture Sub Picture TV Program selection for PIP Press the PIPCH+ / PIPCH- button to select a channel for the sub picture in PIP mode. D /E 2. Press the G button and then use D Transparency . /E 3. Press the G button and then use D PIP transparency. /E 4. Use the F /G button to select PIP • The adjustment range of PIP Transparency is 0 ~ 10. Selecting an Input Signal Source for PIP/Double PIP/Double Window Window Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. Main Picture Source 32 Plasma TV button to adjust button to make appropriate adjustments. 5. Press the ENTER button to save. TV, Video 1-2, Component 480i Component 480p/720p/1080i, RGB and DVI button to Available Sub Picture Sources TV, Video 1-2, Component 480i/480p/720p/1080i, RGB and DVI TV, Video 1-2, Component 480i External Control Device Setup External Control Device Setup - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor. RS-232C Setup COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 REMOTE CONTROL RS-232C INPUT (CONTROL/SERVICE) DVI INPUT AUDIO INPUT A/V INPUT 1 RGB INPUT VIDEO AUDIO L/MONO AUDIO Antenna S-VIDEO AC INPUT VIDEO PC Type of Connector; D-Sub 9-Pin Male No. Pin name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection RS-232C Configurations 3-Wire Configurations (Not standard) 7-Wire Configurations (Standard RS-232C cable) RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS PC PDP D-Sub 9 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Owner’s Manual 33 External Control Device Setup Set ID - Use this function to specify a monitor ID number. - Refer to ‘Real Data Mapping 1’. See page 35. CHANNEL Language Key lock 1. Press the MENU button and then use D 2. Press the G button and then use D /E /E button to select the SPECIAL menu. PICTURE SOUND button to select Set ID. ISM Method Low power Set ID 3. Press the G button and then use F / G button to adjust Set ID to choose the desired monitor ID number. The adjustment range of Set ID is 1 ~ 99. 4. Press the ENTER button to save. TIMER SPECIAL Caption / Text Captions SCREEN PIP/DW LOCK Communication Parameters • Baud rate :9600 bps (UART) • Data length : 8 bits • Parity : None Menu Prev. • Stop bit : 1 bit • Communication code : ASCII code * Use a crossed (reverse) cable. Transmission / Receiving Protocol Command Reference List Transmission COMMAND 1 COMMAND 2 DATA [Command1][Command2][ ][Set ID][ ][Data][Cr] (Hexadecimal) 01. Power 02. Input Select 03. Aspect Ratio 04. Screen Mute 05. Volume Mute 06. Volume Control 07. Contrast 08. Brightness 09. Color 10. Tint 11. Sharpness 12. OSD Select 13. Remote Control Lock Mode 14. PIP/DW 15. Split Zoom 16. PIP Position 17. Treble 18. Bass 19. Balance 20. Color Temperature 21. Red Adjustment 22. Green Adjustment 23. Blue Adjustment 24. PIP Input Source 25. Abnormal State 26. ISM Method 27. Low Power 28. Orbiter Time Setting 29. Orbiter Pixel Setting 30. Picture Size 31. Auto Config * [Command 1]: First command to control PDP set. (j, k or m) * [Command 2]: Second command to control PDP set. * [Set ID]: You can adjust the set ID to choose desired monitor ID number in Special menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected PDP set is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol. * [DATA]: To transmit command data. Transmit ‘FF’ data to read status of command. * [Cr]: Carriage Return ASCII code ‘0x0D’ * [ ]: ASCII code ‘space (0x20)’ 0~1 0~6 0~3 0~1 0~1 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0 ~ 64 0~1 0~1 0~3 0 ~99 0~3 0 ~ 64 0 ~ 64 0 ~ 64 0~3 0 ~ 3C 0 ~ 3C 0 ~ 3C 0~6 0~a 0~3 0~1 1 ~ FE 1~9 0 ~14 OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer. Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The Monitor transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors. Data 1: Illegal Code 2: Not supported function 3: Wait more time COMCOMDATA 0 DATA 1 DATA 2 DATA 3 MAND 1 MAND 2 (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) 32. Tune Command 33. Channel Add/Del 34. Key 34 Plasma TV 01 ~ 7D 0~1 Key code mainsub/TuneBand External Control Device Setup 01. Power (Command2:a) 05. Volume Mute (Command2:e) G To control Power On/Off of the TV. G To control volume mute on/off. You can also adjust mute using the MUTE button on remote control. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Acknowledgement [k][e][ ][Set ID][ ][Data][Cr] Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on) [a][ ][Set ID][ ][OK][Data][x] * In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function. Acknowledgement [e][ ][Set ID][ ][OK][Data][x] 06. Volume Control (Command2:f) 02. Input Select (Command2:b) (Main Picture Input) G To select input source for the TV. You can also select an input source using the TV/VIDEO button on the TV's remote control. G To adjust volume. You can also adjust volume with the volume buttons on remote control. Transmission Transmission [k][f][ ][Set ID][ ][Data][Cr] [k][b][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’ as shown below. Acknowledgement Data 0 : TV 1 : Video 1 2 : Video 2 3 : Component 1 Acknowledgement 4 : Component 2 5 : RGB 6 : DVI [b][ ][Set ID][ ][OK][Data][x] [f][ ][Set ID][ ][OK][Data][x] 07. Contrast (Command2:g) G To adjust screen contrast. You can also adjust contrast in the Picture menu. 03. Aspect Ratio (Command2:c) (Main picture format) G To adjust the screen format. You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Screen menu. Transmission [k][c][ ][Set ID][ ][Data][Cr] Data 0 Normal screen (4:3) Wide screen (16:9) Horizon Zoom Acknowledgement [c][ ][Set ID][ ][OK][Data][x] Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’ as shown below. Acknowledgement [g][ ][Set ID][ ][OK][Data][x] 08. Brightness (Command2:h) G To adjust screen brightness. You can also adjust brightness in the Picture menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] G To select screen mute on/off. Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’ as shown below. Acknowledgement Transmission [h][ ][Set ID][ ][OK][Data][x] 04. Screen Mute (Command2:d) [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off) Acknowledgement * Real data mapping 1 0 : Step 0 A : Step 10 (SET ID 10) [d][ ][Set ID][ ][OK][Data][x] F : Step 15 (SET ID 15) 10 : Step 16 (SET ID 16) 63 : Step 99 (SET ID 99) 64 : Step 100 Owner’s Manual 35 External Control Device Setup 09. Color (Command2:i) 14. PIP / DW (Command2:n) G To adjust the screen color. You can also adjust color in the Picture menu. G To control the PIP (Picture In picture)/DW (Double Window). You can also control the PIP/DW using the PIP/DW button on the remote control or in the PIP/DW menu. Transmission Transmission [k][i][ ][Set ID][ ][Data][Cr] [k][n][ ][Set ID][ ][Data][Cr] Data Min : 0 ~ Max : 64 • Refer to ‘Real data mapping 1’. See page 35. Acknowledgement Data 0: PIP/DW off 1: PIP [i][ ][Set ID][ ][OK][Data][x] Acknowledgement 2: DW1 3: DW2 [n][ ][Set ID][ ][OK][Data][x] 10. Tint (Command2:j) 15. Split Zoom (Command2:p) G To adjust the screen tint. You can also adjust tint in the Picture menu. G To operate split zoom function and select the split zoom section number. Transmission Transmission [k][j][ ][Set ID][ ][Data][Cr] [k][p][ ][Set ID][ ][Data][Cr] Data Red : 0 ~ Green : 64 • Refer to ‘Real data mapping 1’. See page 35. Data Min: 0 ~ Max:99 • Refer to ‘Real data mapping 2’. Acknowledgement Acknowledgement [j][ ][Set ID][ ][OK][Data][x] [p][ ][Set ID][ ][OK][Data][x] * Real data mapping 2 11. Sharpness (Command2:k) G To adjust the screen sharpness. You can also adjust sharpness in the Picture menu. Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 35. Acknowledgement 0 : 21: 24: 41: 42: 44: 45: 91: Reset split zoom Selection 1 of 2 split Selection 4 of 2 split Selection 1 of 4 split Selection 2 of 4 split Selection 4 of 4 split Selection 5 of 4 split Selection 1 of 9 split zoom zoom zoom zoom zoom zoom zoom 99: Selection 9 of 9 split zoom [k][ ][Set ID][ ][OK][Data][x] 16. PIP Position (Command2:q) G To select OSD (On Screen Display) on/off. G To select sub picture position for PIP. You can also adjust the sub picture position using WIN.POSITION on the remote control or in the PIP/DW menu. Transmission Transmission 12. OSD Select (Command2:l) [k][l][ ][Set ID][ ][Data][Cr] Data 0: OSD off 1: OSD on [k][q][ ][Set ID][ ][Data][Cr] Data 0: 1: 2: 3: Acknowledgement [l][ ][Set ID][ ][OK][Data][x] Right down on screen Left down on screen Left up on screen Right up on screen Acknowledgement 13. Remote Control Lock Mode (Command2:m) [q][ ][Set ID][ ][OK][Data][x] G To lock the remote control and the front panel controls on the monitor. 17. Treble (Command2:r) G To adjust treble. You can also adjust treble in the Sound menu. Transmission [k][m][ ][Set ID][ ][Data][Cr] Data 0: Lock off 1: Lock on Transmission Acknowledgement [k][r][ ][Set ID][ ][Data][Cr] [m][ ][Set ID][ ][OK][Data][x] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 35. Acknowledgement • If you’re not using the remote control and front panel controls on the monitor, use this mode. When main power is on/off, remote control lock is released. 36 Plasma TV [r][ ][Set ID][ ][OK][Data][x] External Control Device Setup 18. Bass (Command2:s) 23. Blue Adjustment (Command2:$) G To adjust bass. You can also adjust bass in the Sound menu. G To adjust blue in color temperature. Transmission Transmission [k][$][ ][Set ID][ ][Data][Cr] [k][s][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 35. Acknowledgement Data Min: 0 ~ Max: 3C • Refer to ‘Real data mapping 3’ as shown below. Acknowledgement [$][ ][Set ID][ ][OK][Data][x] [s][ ][Set ID][ ][OK][Data][x] * Real data mapping 3 0 : -30 1 : -29 2 : -28 19. Balance (Command2:t) G To adjust balance. You can also adjust balance in the Sound menu. Transmission 1E : 0 [k][t][ ][Set ID][ ][Data][Cr] 3A : +28 3B : +29 3C : +30 Data Min: 0 ~ Max: 64 • Refer to ‘Real data mapping 1’. See page 35. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] 24. PIP Input Select (Command2:y) 20. Color Temperature (Command2:u) G To adjust color temperature. You can also adjust ACC in the Picture menu. G To select input source for sub picture in PIP mode. Transmission Transmission [k][y][ ][Set ID][ ][Data][Cr] [k][u][ ][Set ID][ ][Data][Cr] Acknowledgement Data 0 [u][ ][Set ID][ ][OK][Data][x] Acknowledgement Data 0: Cool 1: Normal 2: Warm 3: Off : TV : Video 1 : Video 2 : Component 1 4 : Component 2 5 : RGB 6 : DVI [y][ ][Set ID][ ][OK][Data][x] 21. Red Adjustment (Command2:v) G To adjust red in color temperature. Transmission [k][v][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 3C • Refer to ‘Real data mapping 3’ as shown right. Acknowledgement [v][ ][Set ID][ ][OK][Data][x] 25. Abnormal State (Command2:z) G To recognize an abnormal state. Transmission [k][z][ ][Set ID][ ][FF][Cr] Data FF:Read Acknowledgement [z][ ][Set ID][ ][OK][Data][x] 22. Green Adjustment (Command2:w) G To adjust green in color temperature. Transmission [k][w][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 3C • Refer to ‘Real data mapping 3’ as shown right. Acknowledgement [w][ ][Set ID][ ][OK][Data][x] Data 0: Normal (Power on and signal exist) 1: No signal (Power on). 2: Turn the monitor off with remote control. 3: Turn the monitor off with Sleep Time function. 4: Turn the monitor off with RS-232C function. 5: 5V down. 6: AC down. 7: Turn the monitor off with Fan Alarm function. 8: Turn the monitor off with Off Time function. 9: Turn the monitor off with Auto Off function. a: Turn the monitor off with On Time function. (If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.) Owner’s Manual 37 External Control Device Setup 26. ISM Method (Command2:p) G To avoid having a fixed image remain on screen. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data 0: Normal 1: White wash Acknowledgement 31. Auto Configure (Command2:u) G To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission 2: Orbiter 3: Inversion [p][ ][Set ID][ ][OK][Data][x] [j][u][ ][Set ID][ ][Data][Cr] Data 1: To set Acknowledgement [u][ ][Set ID][ ][OK][Data][x] 27. Low Power (Command2:q) G To control the low power function on/off. Transmission [j][q][ ][Set ID][ ][Data][Cr] Data 0: Low power off 1: Low power on Acknowledgement [q][ ][Set ID][ ][OK][Data][x] 32. Tune command (Command: m a) G Tune channel to following physical number Transmission [m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][Cr] 28. Orbiter Time Setting (Command2:r) Data 0: Air: 02 ~ 45, Cable: 01, 0E ~ 7D 1: 0 2: 0 3: High → Main Channel: 0, Sub Channel: 1 Low → Air: 0, CATV: 1 G To adjust orbiter operation time term. Acknowledgement Transmission [a][ ][Set ID][ ][OK][Data0][ ][Data1][ ][Data2][ ][Data3][x] [j][r][ ][Set ID][ ][Data][Cr] Data Min: 1 ~ Max: FE 33. Channel Add/Del (Command: m b) Acknowledgement [r][ ][Set ID][ ][OK][Data][x] G To add and delete the channels Transmission [m][b][ ][Set ID][ ][Data][Cr] 29. Orbiter Pixel Setting (Command2:s) G To adjust pixel number in orbiter function. Data 0: Channel Memory 1: Channel Erase Transmission Acknowledgement [j][s][ ][Set ID][ ][Data][Cr] [b][ ][Set ID][ ][OK][Data][x] Data Min: 1 ~ Max: 9 Acknowledgement [s][ ][Set ID][ ][OK][Data][x] 34. Key (Command: m c) G To send IR remote key code Transmission [m][c][ ][Set ID][ ][Data][ ][Cr] 30. Picture Size Setting for Double Window mode (Command2:t) Data Key code: Refer to page 40. G To adjust main window size in Double Window mode. Acknowledgement Transmission [c][ ][Set ID][ ][OK][Data][x] [j][t][ ][Set ID][ ][Data][Cr] Data Min: 0 ~ Max: 14 • Refer to ‘Real data mapping1’. See page 35. Acknowledgement [t][ ][Set ID][ ][OK][Data][x] 38 Plasma TV IR Codes IR Codes How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz TC Carrier frequency FCAR = 1/TC = fOSC/12 Duty ratio = T1/TC = 1/3 T1 G Configuration of frame • 1st frame Lead code Low custom code High custom code Data code Data code C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 • Repeat frame Repeat code Tf G Lead code 9 ms 4.5 ms 0.55 ms G Repeat code 9 ms 2.25 ms G Bit description • Bit “0” • Bit “1” 0.56 ms 0.56 ms 1.12 ms 2.24 ms G Frame interval : Tf The waveform is transmitted as long as a key is depressed. Tf Tf Tf=108ms @455KHz Owner’s Manual 39 IR Codes Code (Hexa) 00 01 02 03 08 C4 C5 09 10 11 12 13 14 15 16 17 18 19 0B 98 D6 5A D0 BF D4 C6 D5 0E 43 44 4D 52 60 61 63 64 62 71 72 7B 79 76 77 AF 1E 1A 54 55 0A 39 99 40 Plasma TV Function CH (D) CH (E) VOL (G) VOL (F) POWER POWER ON POWER OFF MUTE Number Key 0 Number Key 1 Number Key 2 Number Key 3 Number Key 4 Number Key 5 Number Key 6 Number Key 7 Number Key 8 Number Key 9 TV/VIDEO MULTIMEDIA TV VIDEO1 VIDEO2 COMPONENT1 COMPONENT2 DVI RGB SLEEP MENU ENTER APC DASP PIP/DW PIP INPUT SWAP WIN.SIZE POSITION PIP CH+ PIP CHSPLIT ZOOM ARC ARC (4:3) ARC (16:9) ARC (Zoom) FCR REVIEW AUTO PROGRAM MEMORY/ERASE MTS CAPTION AUTO CONFIG Note R/C Button R/C Button R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (Input TV Selection) Discrete IR Code (Input VIDEO1 Selection) Discrete IR Code (Input VIDEO2 Selection) Discrete IR Code (Input COMPONENT1 Selection) Discrete IR Code (Input COMPONENT2 Selection) Discrete IR Code (Input DVI Selection) Discrete IR Code (Input RGB Selection) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (Only 4:3 mode) Discrete IR Code (Only 16:9 mode) Discrete IR Code (Only Zoom mode) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code Troubleshooting Checklist Troubleshooting Checklist • Check whether the TV is turned on. No picture & No sound • Is the power cord inserted into wall power outlet? • Test the wall power outlet, plug another product’s power cord into the outlet where the TV’s power cord was plugged in. Picture OK & No sound • Press the VOLUME (G) button. • Sound muted? Press MUTE button. • Check to see if there is any object between the TV and the remote control causing obstruction. The remote control doesn’t work • Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.9) • Correct remote operating mode set: TV, VCR etc.? • Install new batteries. (Refer to p.9) Picture appears slowly after switching on • This is normal, the image is muted during the TV startup process. Please contact your service center, if the picture has not appeared after five minutes. • Select Color in the Picture menu and press the VOLUME (G) button. (Refer to p.20) No or poor color or poor picture • Keep a sufficient distance between the TV and the VCR. • Activate any function to restore the brightness of the picture. (If still picture is on the screen for more than 5 minutes, the screen gets dark.) Horizontal/vertical bars or picture shaking • Check for local interference such as an electrical appliance or power tool. No output from one of the speakers • Adjust Balance in the Sound menu. (Refer to p.22) Unusual sound from inside the TV • A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the TV. Owner’s Manual 41 Maintenance & Specification Maintenance - Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning. Cleaning the Screen 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV. Cleaning the Cabinet To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth. Extended Absence If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. Product Specifications MODEL RU-42PZ61/71 RU-50PZ61 RU-60PZ61 Width (inches / mm) 48.4 / 1210 55 / 1400 56 / 1400 Height (inches / mm) 27.6 / 701 32.3 / 821 30.4 / 761.5 Depth (inches / mm) 11.6 / 295 12.4 / 315 11.4 / 290 Weight (pounds / kg) 76 / 34.6 115 / 52.2 66 / 29.9 Resolution 852 x 480 (Dot) 1366 x 768 (Dot) Power requirement AC100-240V, 60Hz Television System NTSC Program Coverage VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125 External Antenna Impedance 75 Ω Color 16,770,000 (256 steps of each R, G and B) Operating Temperature Range 32 ~ 104°F (0 ~ 40°C) Operating Humidity Range Less than 80% Maximum Elevation 6561 feet (2000m) 1366 x 768 (Dot) • The specifications shown above may be changed without notice for quality improvement. 42 Plasma TV LG ELECTRONICS, INC. PLASMA TV — U.S. LIMITED WARRANTY Your LG Plasma TV will be repaired or replaced in accordance with the terms of this warranty, at LGE’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, including Alaska, Hawaii, and U.S. Territories. WARRANTY PERIOD: HOW SERVICE IS HANDLED: LABOR and PARTS: 2 YEARS from the Date of Purchase. Your unit will be repaired or replaced with a new, substitute model or factory reconditioned unit, at LGE’s option. If repaired, parts used in the repair may be new or remanufactured. Replacement Units and Repair Parts are warranted for the remaining portion of the original unit’s warranty period. In-Home Service: Please retain dealer’s dated bill of sale or delivery ticket as evidence of the Date of Purchase for proof of warranty, and submit a copy of the bill of sale to the service person at the time warranty service is provided. EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user. KEEP THE DEALER’S DATED BILL OF SALE OR PROOF OF DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service. Please call 1-201-816-2000 to locate your nearest LGE Authorized Service Center. Visit our website at: http://www.lgservice.com THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state. CONCERNING PIXEL FUNCTIONALITY: Your Plasma TV contains about one million individual pixels. Plasma TV typically contain a small number of pixels that do not function normally. Your display has been inspected and is in compliance with manufacturer’s specifications, indicating that any pixel defects do not effect the operation or use of your display. IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your product online. This information will allow us to reach you promptly should we discover a safety or reliability problem that could affect you. THIS LIMITED WARRANTY DOES NOT APPLY TO: ● ● ● ● ● ● ● ● damage caused in shipping or transit service required as a result of improper installation, including incorrect or insufficient AC supply (please consult the owner’s manual for power supply requirements) installation or repair of antenna systems, cable converters, cable company supplied equipment, or other components in a video system set-up or adjustment on consumer controls, or damage caused by improper adjustments damage caused by other system components any panel that has been modified or incorporated into any other product replacement of batteries on the remote control. damage (including cosmetic damage), failure, loss or personal injury due to misuse, abuse, negli- ● ● ● ● ● gence, improper maintenance or storage, or to acts of nature or other causes beyond our control. (Causes beyond our control include but are not limited to lightning strike, power surges, power outages and water damage.) image burn-in repair or replacement of warranted parts by other than LGE authorized service centers. units purchased or serviced outside of the coverage area. product where the original factory serial numbers have been removed, defaced or changed in any way. product sold and labeled as “as is, where is” or similar disclaimer. The cost of repair or replacement under these excluded circumstances shall be borne by the consumer. CUSTOMER INTERACTIVE CENTER NUMBERS: To obtain customer assistance, product information or Dealer or Service locations Call 1-201-816-2000 24 hours a day, 365 days per year FOR SERVICE: Before you call for warranty service, check your operating guide – you may avoid a service call. For warranty service information, please contact the LGE Customer Interactive Center telephone number. When calling for service, please have your product model number, serial number and the date of purchase or the date of original installation available. If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not be charged if you return the defective unit within 10 working days. If a replacement unit is received, please use the carton and packaging from that unit in returning the defective unit to the LG®Brand Service Center. Parts and service in accordance with the LGE warranty are LGE’s responsibility and will be provided without charge. Other service requirements will be at the owner’s expense. If you have problems in obtaining satisfactory warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently owned and operated service organizations. To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before returning any product to the LGE Service Center. Contact the Customer Interactive Center for details. TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL: LGE Customer Interactive Center P.O. Box 240007 201 James Record Road Huntsville, Alabama 35824 http://www.lgservice.com P/N : 3828VA0470P
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 1997:08:05 13:31:42 Producer : Acrobat Distiller 4.0 for Macintosh Creator : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Author : PSY Title : 470Pen Modify Date : 1997:08:05 13:32:30+09:00 Page Count : 44EXIF Metadata provided by EXIF.tools