LG Electronics USA RU60SZ10 LCD Projection TV User Manual G User s Manual
LG Electronics USA LCD Projection TV G User s Manual
users manaul
FCC ID : BEJRU60SZ10 APPENDIX G : USER’S MANUAL Installation and Operating Guide | Warranty Model Number | D60WLCD | LCD TV © Copyright 2002, Zenith Electronics Corporation. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. POWER CORD POLARIZATION: CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND. NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical. REGULATORY INFORMATION: This equipment, trade name Zenith, model number, D60WLCD, has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. The responsible party for this device compliance is: Zenith Electronics Corporation 2000 Millbrook Drive Lincolnshire, IL 60069 Digital TV Hotline: 1-847-941-8000 CAUTION: Do not attempt to modify this product in any way without written authorization from Zenith Electronics Corporation. Unauthorized modification could void the user’s authority to operate this product. 2002 Zenith Electronics Corporation. All rights reserved. PAGE 2 206-03726 IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference. Observing the simple precautions discussed in this booklet can help you get many years of enjoyment and safe operation that are built into your new product. This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association. 1. Read Instructions 9. Attachments All the safety and operating instructions should be read before the product is operated. Do not use attachments not recommended by the product manufacturer as they may cause hazards. 2. Follow Instructions 10. Ventilation All operating and use instructions should be followed. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to. 3. Retain Instructions The safety and operating instructions should be retained for future reference. 4. Heed Warnings All warnings on the product and in the operating instructions should be adhered to. 5. Cleaning Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 6. Water and Moisture Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool. 7. Accessories Carts and Stands Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer. 8. Transporting Product A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn. 11. Power Sources This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions. 12. Power-Cord Polarization This product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. 13. Power-Cord Protection Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. (Continued on next page) 206-03726 PORTABLE CART WARNING PAGE 3 IMPORTANT SAFETY INSTRUCTIONS (Continued from previous page) 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded to provide protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. Example of Grounding According to National Electrical Code Instructions Ground Clamp Antenna Lead in Wire Antenna Discharge Unit (NEC Section 810-20) Electric Service Equipment Fig. 1 Grounding Conductor (NEC Section 810-21) Ground Clamps Power Service Grounding Electrode System (NEC Art 250, Part H) NEC - National Electrical Code openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. 19. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 20. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been damaged. f. If the product exhibits a distinct change in performance. 21. Replacement Parts 15. Lightning For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 16. Power Lines An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 17. Overloading Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 18. Object and Liquid Entry When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 22. Safety Check Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. 23. Wall or Ceiling Mounting The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. 24. Heat The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Never push objects of any kind into this product through PAGE 4 206-03726 Table of Contents Safety Warnings . . . . . . . . . Important Safety Instructions EZ Help . . . . . . . . . . . . . . Function Status Indicators . . .2 .3 .6 .7 Step 1. Hook Up TV Rear Jack Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Front Jack Panel . . . . . . . . . . . . . . . . . . . . . . . . . . .9 ANT/CABLE Hookup . . . . . . . . . . . . . . . . . . . . . . . . .10 CABLE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 VCR + CABLE BOX . . . . . . . . . . . . . . . . . . . . . . . . . .12 DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 HD-SET TOP and PC Hookup . . . . . . . . . . . . . . . . . . .14 External Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Room Setups for Home Theater . . . . . . . . . . . . . . . . .16 Monitor Out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Remote Button Functions . . . . . . . . . . . . . . . . . . .18-19 On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . .20 Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . .21 Step 2. Customize your TV’s Features SETUP Menu Main Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 PIP Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 PIP/POP/SPLIT . . . . . . . . . . . . . . . . . . . . . . . . .24-25 EZ Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Channel Add/Del/Surf . . . . . . . . . . . . . . . . . . . . . .27 Channel Label . . . . . . . . . . . . . . . . . . . . . . . . . . .28 EZ Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 206-03726 VIDEO Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .30-31 AUDIO Menu . . . . . . . . . . . . . . . . . . . . . . . . . . .32-33 SPECIAL Menu Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 On-Screen Language . . . . . . . . . . . . . . . . . . . . . . . 35 Captions/Text . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 EZ Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 TIME Menu Auto Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Manual Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 On Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 Off Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 LOCK Menu Parental Lock . . . . . . . . . . . . . . . . . . . . . . . . . .43-45 Programming the Remote . . . . . . . . . . . . . . . . . . . . .46 Programming Codes . . . . . . . . . . . . . . . . . . . . . .47-50 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .51-52 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .53-54 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55-56 Product Specifications . . . . . . . . . . . . . . . . . . . . . .57 Your Zenith Warranty . . . . . . . . . . . . . . . . . .Back Cover Note: Design and specifications are subject to change without prior notice. PAGE 5 EZ Help EZ Help was created as an aid for you to understand menu functions in an easy and convenient way. When you navigate through the Menu, press and hold the HELP (?) button on your remote control to learn about the highlighted option or feature Information about the highlighted option will be displayed on the right side of the TV screen. Press and hold HELP (?) to see the highlighted information. Menu NOTE : The HELP (?) button on the remote control can be used in two ways. You can press the HELP (?) button independently to display the EZ HELP feature. When a MENU is already displayed, you can press the HELP (?) to go to the EZ HELP feature. The EZ Help feature: 1. Press the HELP (?) button on the remote control to display the EZ Help menu. 2. Scroll up and down to select EZ Help menu items by using “D E”on the remote control thumbstick. 3. Move the highlight by using “D EF G” on the thumbstick. The explanations of the highlighted option will be displayed on the right side or at the bottom of the screen. 4. Press the EXIT button on the remote control to TV viewing. PAGE 6 206-03726 Function Status indicators Lamp indicator, operation indicator, and temperature indicator located below the front panel controls reveal the operating status of the LCD projection TV. power menu enter vol ch Operation indicator Temperature indicator Lamp indicator Operation Indicator Off Orange Green Green (flashing) Orange Red Lamp Indicator Red (flashing) Temperature Indicator 206-03726 Green (flashing) Orange Red Red (flashing) Power off. Standby On Preparing operation in standby. Projection lamp is reaching the end of its life and needs to be replaced with a new lamp. Projection lamp is dead and needs to be replaced with a new lamp. There is a problem with the lamp or around it. Contact an authorized service center. The lamp cover is not closed. The projector is overheating. The projector shutdown due to overheating. The projector shutdown, check the cooling fan. PAGE 7 Rear Audio/Video Jacks Connecting cables to your Entertainment Machine. RF Connectors: Antenna/Cable 1, Antenna/Cable 2, and Loop Out Used to connect analog cable or antenna signals to the television, either directly or through your cable box. PC and HD-STB Input Used to connect from a PC source or HD-STB Satellite system. PC and HD-STB Audio Input Used for audio connections from a PC source or HD-STB Satellite system. ANT/CABLE2 INPUT LOOP OUT ANT/CABLE1 INPUT PC/DTV INPUT RGB (XGA) S-VIDEO Variable Audio Out Used to connect either an external amplifier, or add a sub-woofer to your surround sound system. AUDIO CENTER MODE IN VARIABLE AUDIO OUT PR PB VIDEO COMPONENT INPUT 2 S-VIDEO In A connection available with some high-end equipment that provides even better picture quality for Video 1. MONO COMPONENT INPUT 1 PR PB DTV/DVD INPUT (480i/480p/720p/1080i) Left/Right Audio Used for stereo sound from various types of equipment. Video 1 or 2 Connects the video signals from various types of equipment. Y, Pb, Pr DVD Component Video and HD Component Video Some top-of-the-line DVD players use what is called “component video,” for extremely accurate picture reproduction. Refer to your DVD manual for further information. MONITOR OUT VIDEO 2 INPUT Center Mode IN Connect to external Dolby Digital Center “preamp output.” VIDEO 1 INPUT Monitor Out Connects to a second TV or Monitor. Left/Right Audio Used for stereo sound from various types of equipment. Mini glossary JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jack and the Audio/Video jacks that are colorcoded. SIGNAL Picture and sound traveling through cable, or over the air, to your television screen. PAGE 8 206-03726 Front Connection Panel There are four jacks on the right side of your Entertainment Machine that make connecting Audio/Video devices like video games and camcorders very simple. The jacks are like those found on the back jack connection panel on your Entertainment Machine. This means that most equipment that connects to those types of jacks on the rear jack pack, may be connected to the side connection panel. To use the side jacks as the signal source, use the Main Source menu as described on page 22. They will be named “Front Video” in the Main Source menu. Front A/V Panel L/MONO VIDEO Video Connects the video signals from any piece of equipment. AUDIO FRONT A/V If you’re connecting a video game unit, make sure to change the picture settings with the EZ Video option in the Video menu (see page 30). S-VIDEO When you select Front Video or Front S-Video, the Front audio inputs are automatically selected as well. S-Video A connection available on some very high-end equipment that provides even better picture quality. Left/Right Audio Used for stereo sound from various types of equipment. Mini glossary A/V CABLES Audio/Video cables. Three cable connectors—Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television). 206-03726 PAGE 9 ANT / CABLE SERVICE Hookup Cable TV wall jack Antenna Connect an antenna and/or cable service wire to your Entertainment Machine as shown. Turn to page 26 to do a channel search with EZ Scan for ANT / CABLE connection(s). RF coaxial wire (75 ohm) RF coaxial wire (75 ohm) ANT/CABLE2 INPUT LOOP OUT ANT/CABLE1 INPUT If you receive your RF signal through an antenna that is several years old and connects with two small prongs, you will need to purchase a 300 to 75 Ohm adapter. It should be available from your local electronics dealer. Zenith recommends using a 75 ohm cable for your antenna connections in order to prevent interference. For best performance, have your Antenna professionally adjusted. PAGE 10 206-03726 Cable Box Connections Some cable services require the use of a cable box to decode premium channels and pay-per-view. Using the Loop Out to Decoder connection option, and programming your remote, you can connect your cable box so that you only need your MBR remote to tune to premium and non-premium channels. By connecting a cable box directly to your Entertainment Machine, as shown using the LOOP OUT, you make the cable box another channel tuning source available using your remote. Locate the Antenna/Cable 2 jack on the back of your TV. Connect the cable that runs from the wall directly to the jack. Now find the Loop Out jack. Connect the cable from this jack to the Input jack on the back of your cable box. Locate the Output jack on the back of your cable box. Connect this to the Antenna/Cable 1 jack on the back of your TV. To view the premium stations, press the TV button on your remote and select the other Cable source (Ant/Cable 1). Then tune the channel number on your cable box for HBO, CINEMAX, SHOWTIME, etc. To view non-premium channels press the TV button and select Ant/Cable 2. Then run EZ Scan to find all available channels and store them in memory. Antenna Cable TV wall jack Cable box Out In ANT/CABLE2 INPUT LOOP OUT ANT/CABLE1 INPUT Rf coaxial wire (75 ohm) S-VIDEO This can be combined with any other equipment you may want to hook up. Hook cable directly into the TV, then to the cable box. From there, the cable box goes to the next device, down the line, until the last piece, which connects back to the TV using the Antenna/Cable 1 jack. 206-03726 VIDEO PAGE 11 VCR/Antenna/Cable Connections Locate the Antenna/Cable 2 jack on the back of your TV. Connect the cable that runs from the wall or antenna to the jack. Now find the Loop Out jack. Connect the cable from this jack to the Input jack on the back of your cable box. Antenna Cable TV wall jack Locate the Output jack on the back of your cable box. Connect this to the RF or VHF/UHF/CATV In jack on the back of your VCR. If you want to connect VCR to the TV directly, connect the cable from the Loop Out jack to the RF or VHF/UHF/CATV In jack on the back of your VCR. Round wire (75ohm) RF coaxial wire (75ohm) Cable box Out or In Find the composite video and audio jacks on the back of your VCR, and connect them following the instructions provided with your equipment. ANT/CABLE2 INPUT LOOP OUT ANT/CABLE1 INPUT VCR You may connect either the composite video or the S-Video cables to your Entertainment Machine. (Do not connect BOTH the composite and the S- Video cables. In the event that you connect both composite and the S-Video cables, only the S-Video will work.) S-VIDEO VIDEO Back AV panel In 3 4 Out Audio Video S-Video MONO MONITOR OUT VIDEO 2 INPUT VIDEO 1 INPUT A/V cables not included with TV To hear stereo sound from cable or your VCR, you will need to connect A/V cables as well as the wire that runs from the VCR to your Entertainment Machine. If you want to receive your signals on Channel 3 or 4, locate the Out to TV jack on your VCR. Connect a cable from the Out to TV jack to the Antenna/Cable 1 jack on the back of your Entertainment Machine. After connecting external equipment to the TV, don’t display a still picture for a long time on the screen. Doing so may damage the unit. PAGE 12 206-03726 DVD Player PC/DTV INPUT DVD Player Find the audio and composite or S-Video jacks on the back of your DVD Player and connect them following the instructions provided with your equipment. RGB (XGA) PR PB PR PB Back AV panel AUDIO CENTER MODE IN VARIABLE AUDIO OUT Audio COMPONENT INPUT 2 Dolby Digital S-Video R Out COMPONENT INPUT 1 DTV/DVD INPUT (480i/480p/720p/1080i) A/V cables not included with TV DVD Player PC/DTV INPUT RGB (XGA) Some high-end DVD players use a picture reproduction system called “component video.” If your DVD player has component output, use the connectors marked “COMPONENT INPUT1” on the jack panel. Please refer to your DVD manual for proper installation. Back AV panel PR PB PR PB AUDIO CENTER MODE IN VARIABLE AUDIO OUT Audio Dolby Digital Component Video Out COMPONENT INPUT 2 COMPONENT INPUT 1 DTV/DVDINPUT (480i/480p/720p/1080i) A/V cables not included with TV Component 1 (or 2) Input Mini glossary COMPONENT VIDEO Some video equipment uses three separate lines (Y, Pb, Pr) to more precisely reproduce images. Your manual will explain how this relates to your equipment. PB PR 1920X1080i 1280X720p 720X480p 720X480i 206-03726 PAGE 13 RGB-PC Input Find the audio and VGA jacks on the back of your DBS receiver (or Computer) and connect them following the instructions provided with your equipment. Connect these cables to your Entertainment Machine as shown. PC/DTV INPUT RGB (XGA) OR Computer AUDIO CENTER MODE IN VARIABLE AUDIO OUT DBS Receiver Component Out Dolby Digital Y Pb Pr Out Audio L R PR PB PR PB COMPONENT INPUT 2 COMPONENT INPUT 1 DTV/DVD INPUT (480i/480p/720p/1080i)MODE Text VGA The DTV shows the sharpest picture in 720p mode. To watch the DTV, connect HD-SET TOP to COMPONENT INPUT2 or PC/DTV INPUT of your TV. SVGA XGA Game PAGE 14 Resolution Horizontal Vertical 640x350 31.5KHz 70Hz 640x480 31.5KHz 60Hz 640x480 37.9KHz 72Hz 640x480 37.5KHz 75Hz 800x600 35.2KHz 56Hz 800x600 37.9KHz 60Hz 800x600 48.1KHz 72Hz 800x600 46.9KHz 75Hz 1024x768 48.4KHz 60Hz 1024x768 56.5KHz 70Hz 1024x768 60.0KHz 75Hz 720x240 15.7KHz 60Hz 206-03726 External Stereo Connections Hook up Left/Right Front Speaker output to an Audio Amplifier System. Locate both the Variable Audio Out jacks on the back of your Entertainment Machine and the Input jacks on the back of your stereo's amplifier. Connect these jacks, making sure that the right and left channels are connected correctly. Adjust the sound on your stereo, according to directions provided with the amplifier. VARIABLE AUDIO OUT 206-03726 PR PB COMPONENT INPUT 2 Analog stereo amplifier Audio cables not included with TV PAGE 15 Room Setups for Home Theater This is just a general room design. Any number of set-ups are possible, and some changes may be needed to maximize your sound. However, a Dolby Digital Receiver is required to hear 5.1 channel audio. A left and right speaker on either side of the set enhances separation. The Entertainment Machine “center mode in,” makes the dialog sound as thought it’s coming directly from the Entertainment Machine. The rear surround sound speakers provide the majority of other sounds, like those from special effects in movies. Your sub-woofer generates ultra-low frequency sound, for rumbling low-end audio. left speaker surround sound speaker right speaker sub-woofer surround sound speaker Sound is affected by speaker placement, so make sure nothing is in front of the speakers, and that they are aimed in appropriate directions. You have the option of turning the internal speakers on or off. PAGE 16 206-03726 Monitor Out Setup Your Entertainment Machine has a special feature which allows you to hook up a second TV or monitor. Just connect the second TV or monitor using the MONITOR OUT Audio/Video jacks located on the back of your Entertainment Machine. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings. S-VIDEO Second TV VIDEO PB MONO PR MONITOR OUT VIDEO 2 INPUT S-Video Video Audio VIDEO 1 INPUT A/V cables not included with TV Component & PC input sources cannot be output through Monitor Out. 206-03726 PAGE 17 Remote Functions in TV Mode INDICATORS MODE Selects the remote operating mode: TV, VCR, Cable, DVD and Satellite. TV vcr cable dvd sat tv mode light power Selects the analog TV signal. source VIDEO Toggles between Video 1 and Video 2 input sources. MUTE Switch the sound on or off PIPCHChanges to next lower PIP channel SWAP Swap the signal from your PIP window to the main screen. tv video front comp1 comp2 rgb enter LIGHT Illuminates the remote control keys. FRONT Selects the front video signal if a device, such as a camcorder or game player, is connected to the front video input jack. RATIO Changes the screen format or aspect ratio. PIPCH+ Changes to next higher PIP channel. ratio mute vol ch swap pipch- pipch+ pip THUMBSTICK Allows you to navigate the on-screen menus and to adjust the system settings and preferences, by moving to an option withF E G and selecting the highlighted option with . If is pressed while you are in normal viewing, the information banner is displayed. Light to show remote mode every time any button is pressed. menu flashbk surf freeze PIP Lets you toggle betwen PIP, POP (Picture-out-of-Picture) and Split screen. SURF Scrolls the Surf channel list. exit HELP Brings up the on-screen EZ Help menu while you are in normal viewing. EXIT record stop pause rew PAGE 18 Clears all on-screen displays and returns to TV viewing from any menu. skip play ff 206-03726 Remote Button Functions vcr cable dvd sat tv MODE BUTTONS Select other operating modes, for the remote to control external devices. mode light power POWER Turns your Entertainment Machine or any other programmed equipment on or off, depending on mode. source COMPONENT 1, 2 Selects component signal sources, such as DVD or HD receiver. tv video front comp1 comp2 rgb enter NUMBER KEYPAD For direct channel selection and programming functions. RGB Selects PC or RGB input sources. ENTER Selects the highlighted option in the menu system or on-screen displays. “DASH” BUTTON Is used to enter a program number for multiple program channels such as 2—1,2—2,etc. VOLUME UP/DOWN CHANNEL UP/DOWN ratio mute Scrolls through available channels in EZ Scan memory. Increases/decreases the sound level. vol ch FLASHBK MENU Brings up the main menu to the screen. swap pipch- pipch+ pip Tunes to the last channel viewed. menu flashbk surf FREEZE freeze Captures and freezes the currently-viewed screen in PIP. exit record stop RECORD, PAUSE, REW, FFWD, PLAY, STOP Control the functions on your VCR. 206-03726 pause rew When in the menu system and other on-screen displays, selects high lighted options. SKIP skip play ENTER ff Works as a song selector in audio mode and a movie chapter selector in aux/DVD mode. PAGE 19 On-Screen Displays This page describes your on-screen display and information banner options. Channel Label: If a channel label has been set, then it will appear here. Main Channel Display: Displays current channel number. Ch. 13 MONO PIP Display: This display appears when PIP is active. Ch.6 AM 03:00 10 Mute: Appears when sound is muted. PAGE 20 Volume: Volume level is displayed while adjusting the sound. Time: Appears when pressing the enter button on remote control. 206-03726 Front Panel Controls Power On / Off Menu Enter (Same as ENTER buttons on your remote control) VOLUME Up / Down CANNEL Up / Down Lamp indicater. (See page 7). Temperature indicater. (See page 7). Operation indicater. (See page 7). power menu enter vol ch Refer to the various pages on how to use the on-screen menus. The POWER, CHANNEL and VOLUME buttons work just as they do on your remote control. 206-03726 PAGE 21 Main Picture Source Selection Changes the picture source for the main screen so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that you have hooked up to your TV. You can also change the picture source with the Source buttons on the remote control. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Setup menu. vcr cable dvd sat tv mode Press ENTER or the RIGHT arrow button to access the Setup menu. light power source Use the UP/DOWN arrows to select Main source. Press ENTER or the RIGHT arrow to access the Main source menu, then use the UP/DOWN arrow button to select the source. Your picture source options are : Ant/Cable 1 (Ant/Cable 2), Video 1, Video 2, Front Video, Component 1, Component 2 and RGB-PC. Press EXIT to save and return to TV viewing or press the LEFT arrow to save and return to the previous Menu. tv video front comp1 comp2 rgb enter ratio mute vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew PAGE 22 2/4 1/3 2/4/5 skip play ff 206-03726 PIP Picture Source Selection Changes the picture source for the Picture-In-Picture screen so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that you have hooked up to your TV. You can also change the PIP screen source using the PIP button on the remote control. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Setup menu. mode Press ENTER or the RIGHT arrow button to access the Setup menu. Use the UP/DOWN arrows to select the PIP Source option. Press ENTER or the RIGHT arrow to access the PIP source menu, then use the UP/DOWN arrow button to select the source. Your choices are: Ant/Cable 1, Video 1, Video 2, Front Video, Component 1, Component 2. vcr cable dvd sat tv light source tv video front comp1 comp2 rgb enter Press EXIT to save and return to TV viewing or press the LEFT arrow to save and return to the previous Menu. ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew 206-03726 2/4 ratio mute vol power 1/3 2/4/5 skip play ff PAGE 23 PIP/POP/SPLIT Sources PPIP (Picture-in-Picture) / POP (Picture-out-ofPicture) / SPLIT modes let you watch main and sub pictures at the same time. PIP/POP/SPLIT modes turn off in instances indicated below. • Changing main source • Changing Aspect Ratio • Activating Channel Add/Del/Surf, Channel Label or Channel Block in Setup menu • Activating Help menu Press the PIP button on the remote control to activate PIP (Picture in Picture) mode. Press the LEFT/RIGHT arrow to select CH+/-, Swap, Source or Move. • CH+/- : Use the UP/DOWN arrow to select a program for the sub picture. Changing programs on the sub picture is only possible if the PIP signal source is NTSC RF signal. If you want to change the program on the main picture, press pg up/dn button. vcr cable dvd sat tv mode light power source tv video front comp1 comp2 rgb enter ratio mute • Swap : Use the UP/DOWN arrow to swap main and sub picture. • Source : Use the UP/DOWN arrow to select a source for sub picture. Your choices are : TV, Video1/2, Front, Component 1/2. RGB-HD/STB and RGB-PC input sources cannot used as PIP screen source. • Move : Use the UP/DOWN arrow to move the sub picture on the screen. Press the EXIT button to exit PIP mode or press the PIP button again to activate POP mode. PAGE 24 vol ch swap pipch- pipch+ pip menu flashbk surf 1/3 freeze exit record stop pause rew skip play ff 206-03726 PIP/POP/SPLIT Press the PIP button on the remote control in PIP mode to activate POP (Picture -out-of-Picture) mode. Press the EXIT button to exit POP mode or press the PIP button again to activate Split mode. Press the LEFT/RIGHT arrow in Split mode to select CH+/-, Swap, or Source. • CH+/-: Use the UP/DOWN arrow to select a program for the sub picture. Changing programs in the sub picture is only possible if the PIP source is NTSC RF signal. To change the program for the main picture, use ch +/- button. • Swap: Use the UP/DOWN arrow to swap main and sub pictures. • Source: Use the UP/DOWN arrow to select a source for sub picture. Your choices are : TV, Video1/2, Front, Component 1/2. RGB-PC input cannot used for the PIP picture source. vcr cable dvd sat tv mode light power source tv video front comp1 comp2 rgb enter ratio mute vol ch swap pipch- pipch+ pip menu flashbk surf 1/2 freeze exit 2/4 Press the EXIT button to exit Split mode. record stop pause rew skip play ff Press the FREEZE button to capture and freeze the currently-viewed sub picture in PIP or Split mode. Do not display a fixed image on the screen for long periods of time. 206-03726 PAGE 25 EZ Scan Automatically finds analog channels available through antenna and cable inputs, and stores all active channels in memory on the channel list. Use pages 10-14 to hook up your Entertainment Machine. If you have not done so, plug in your Entertainment Machine into a 120V 60Hz power outlet. vcr cable dvd sat tv mode light power source If you have not done so, remove the back of the remote and put in two AA batteries. Make sure batteries are properly installed (check the +/– signs). back of remote tv video front comp1 comp2 rgb enter vol With the remote control in hand, press the POWER button to turn on your Entertainment Machine. ch swap pipch- pipch+ pip menu flashbk surf Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Setup menu. Press ENTER or the RIGHT arrow button to access the Setup menu. Use the UP/DOWN arrows to select EZ Scan. freeze exit Press ENTER or the RIGHT arrow to access the EZ Scan smenu, then use the UP/DOWN arrows to select: ANT1 Air, ANT1 Cable, ANT2 Air, ANT2 Cable Press ENTER or the Right arrow button to start the EZ Scan channel search. PAGE 26 5/7/8 ratio mute record stop pause rew 4/6 5/7/8 skip play ff 206-03726 Channel Add / Del / Surf Setup Create two different types of channel lists in memory : “Custom list” and “Surf list” from the default channel list made in the EZ SCAN menu. A custom list can be created by toggling each channel on or off with (Enter). Once a channel is highlighted, you will be able to see whether the channel is currently added or deleted by referring to the small window at the top-left corner of the screen. You can create your own Surf list with up to 16 channels. It appears at the bottom-left corner of the screen. Press the Surf button on the remote control when a channel is highlighted to add or delete the channel in the Surf list. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Setup menu. Press ENTER or the RIGHT arrow button to access the Setup menu. Use the UP/DOWN arrows to select Channel Add/Del/Surf and then press ENTER or right arrow. 206-03726 You will now see a screen filled with channel numbers and a preview picture. Use the UP/DOWN and LEFT/RIGHT arrows to select a channel, then use ENTER to add or delete it. Press SURF to add the channel to the Surf list. vcr cable dvd sat tv mode light power source tv video front comp1 comp2 rgb enter 2/3 ratio mute vol ch swap pipch- pipch+ pip 1/5 menu flashbk surf freeze exit record stop pause rew 1/3/4 2/3/4 skip play ff Press EXIT to save and return to TV viewing or press MENU to save and return to the previous menu. PAGE 27 Channel Label Setup Choose preset labels for your channels. Use Channel +/- on your remote control in the CH Label menu to select a channel for labeling, and choose a suitable label for your channel by pressing to set the label to the selected channel. vcr cable dvd sat tv mode Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Setup menu. light power source tv video front comp1 comp2 rgb Press ENTER or the RIGHT arrow button to access the Setup menu. Use the UP/DOWN arrows to select the CH Label option. enter Press ENTER or the RIGHT arrow to access the CH.Label menu. You will now see a screen filled with Labels and a preview screen. Use channel UP/DOWN button on your remote to select the a channel to Label. vol ch swap pipch- pipch+ pip menu flashbk surf Use the UP/DOWN and LEFT/RIGHT arrows to select the appropriate label for the channel and press ENTER to set the Label to the selected channel. Repeat steps five and six until all channels are Labeled. 2/4/6 ratio mute freeze exit record stop pause rew 1/3/5/6 2/4/6 skip play ff Press EXIT to save and return to TV viewing. PAGE 28 206-03726 EZ Link Setup Lets you link the Zenith’s READY TV (Model: D60WLCD) and Zenith’s high definition set settop box for DIRECT TV via a RS-232C cable. After installing the EZ link, you can control a settop box for the DIRECT TV with a remote control of the Zenith’s READY TV. vcr cable dvd sat tv Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Setup menu. Press ENTER or the RIGHT arrow button to access the Setup menu. Use the UP/DOWN arrows to select EZ Link and then press ENTER or the RIGHT arrow button. Use the UP/DOWN arrows to choose On or Off. Press EXIT to save and return to TV viewing or press the LEFT arrow to save and return to the previous Menu. mode light power source tv video front comp1 comp2 rgb enter mute vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew 206-03726 2/3 ratio 1/3/4/5 2/3 skip play ff PAGE 29 VIDEO Menu Lets you adjust the picture appearance to suit your preference and viewing situations. You can manually adjust the levels of picture quality settings, such as Contrast, Brightness, Sharpness, etc. You can also select the preset value in the EZ Video menu based on the program category. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Video menu. vcr cable dvd sat tv mode Press ENTER or the RIGHT arrow button to access the Video menu. light power source Use the UP/DOWN arrows to select one of the following options. Your options are: Contrast, Brightness, Sharpness, color, Tint, EZ Video (Custom, Normal, Movie, Video Game, Sports, Weak Signal and Daylight). Then press ENTER or the Right arrow button. Use the LEFT/RIGHT arrows to adjust the option to your preference. Press ENTER to save your choices and return to the previous menu or use the UP/DOWN arrows to select another option. tv video front comp1 comp2 rgb enter ratio mute vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew PAGE 30 2/3/5 1/3/5 2/3/4 skip play ff 206-03726 VIDEO Menu • Contrast: Adjusts the difference between the light and dark levels of the picture. Press the right arrow button to activate adjusting. • Brightness: Adjusts the white or light level of the overall picture. • Sharpness: Adjusts the level of crispness in the edges between the light and dark areas of the picture. The lower the level, the softer the image. • Color: Adjusts the intensity of all colors. • Tint: Adjusts the balance between the red and green levels. • EZ Video: Lets you choose the preset value of the picture settings. Custom: Lets you adjust the picture settings manually. Normal: Restores the levels to their original picture settings. Movie Adjusts Video settings to enhance Movie viewing. Contrast and Sharpness levels are lowered so that the picture looks warm and soft. Video Game: Sets the picture settings to the levels that are more suitable to enjoy games. Color, Contrast and Sharpness levels are lowered to reduce the amount of glare. Sports: Sets the picture settings to the levels that are more suitable to view sporting events. Contrast and Color levels are raised so that an action scene appears clear and brilliant. Weak Signal: Adjusts the picture settings to compensate for a weak signal reception. Contrast, Color and Sharpness levels are lowered to hide the picture imperfections. Daylight: Increases the levels of all picture settings to fit daylight conditions. 206-03726 PAGE 31 AUDIO Menu Lets you adjust the sound to suit your taste and room situations. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Audio menu. vcr cable dvd sat tv mode light power source Press ENTER or the RIGHT arrow button to access the Audio menu. Use the UP/DOWN arrows to select one of the following options. Your options are: Bass, Treble, Balance, EZ sound, EZ sound Rite, Audio Mode, Front Surround and Internal Speaker. Then press ENTER or the RIGHT arrow button. video front comp1 comp2 rgb enter Use the UP/DOWN arrows to select your preference (Bass, Treble, Balance), then use the LEFT/RIGHT arrows to adjust the option to your preference. vol ch swap pipch- pipch+ pip menu flashbk surf freeze Press ENTER to save your choices and return to the previous menu. exit record stop pause rew PAGE 32 2/3/5 ratio mute tv 1/3/4 2/3/4 skip play ff 206-03726 AUDIO Menu • Bass: Increases or decreases the lower frequency sounds of the TV speakers. • Treble: Increases or decreases the higher frequency sounds of the TV speakers. Increases in treble, for example, make voice or string sounds stand out • Balance: Lets you adjust the left to right balance of the TV speakers. • EZ Sound: Lets you choose the sound settings manually. Custom: Lets you adjust the Audio menu sound options manually. Normal: Restores the sound levels to their original settings. Stadium: Stresses high frequency sounds and front surround sound to create the sensation you would experience in a stadium. News: Increase high frequency sounds to emphasize the human voice. Music: Increase both high and low frequency sounds to stress the sounds of musical instruments. Theater: Stresses both high and low frequency sounds, in addition to the front surround sound, to create the sensation you would experience in a theater. • EZ Sound Rite: Scans for changes in sound level during commercials, then adjusts the sound to match the current audio level of the TV program you are watching. • Audio Mode: Lets you choose the default audio mode for conventional analog programs. When you hear a program broadcast in mono, you will hear only monaural sound, even though Stereo mode is set. When Second Audio Program (SAP) mode is set, the program's second audio program, usually the program's dialog in another language, (if provided), is broadcast in mono. • Front Surround: Increases the front surround sound to create more open and expanded sound. • Internal Speaker: Allows you to toggle the TV internal speakers Stereo, Center or off. If you want to use your external hi-fi stereo system, turn off the internal TV speakers. However, you may use the internal TV speakers as a center speaker to create a surround effect. 206-03726 PAGE 33 Aspect Ratio Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Special menu. Or press RATIO button to instantly access the Aspect Ratio menu. Press ENTER or the RIGHT arrow button to activate the Special menu. Use the UP/DOWN arrows to choose Aspect Ratio. Press ENTER or the RIGHT arrow button to move into the Aspect Ratio selection menu. Use the UP/DOWN arrow buttons to select the right ratio for your viewing environment: • Normal - Choose when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. Lets you choose the way that an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed according to your preference. • Wide - Choose when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. (Useful for viewing 4:3 formatted DVDs.) vcr cable dvd sat tv mode light source • Panorama - Choose when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. • Zoom1 - Choose when you want to view the picture without any alteration. However, the top and bottom portion of the picture will be cropped. tv video front comp1 comp2 rgb enter ratio mute vol • Zoom2 - Choose when you want the picture to be altered, both horizontally enlarged and vertically cropped. The picture taking a halfway trade off between alteration and screen coverage. power ch swap pipch- pipch+ pip menu flashbk surf freeze 1/3/4 Press EXIT to save and return to TV viewing or press the ENTER button to save and return to the previous menu. exit record stop pause rew PAGE 34 2/4/5 2/4 skip play ff 206-03726 On-Screen Menus Language Lets you select your preferred language for the menus: English, Spanish, or French Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Special menu. Press ENTER or the RIGHT arrow button to activate the Special menu. Use the UP/DOWN arrows to choose Trilingual Menus. Press ENTER or the RIGHT arrow button to move into the Language selection menu. Use the UP/DOWN arrow button to select the language you wish to view on your on-screen menus. vcr cable dvd sat tv mode light power source tv video front comp1 comp2 rgb enter ratio mute Press EXIT to save and return to TV viewing or press the ENTER button to save and return to the previous menu. vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew 206-03726 2/4/5 1/3/4 2/4 skip play ff PAGE 35 Captions/Text Lets you select a closed caption mode for displaying captioning information when provided on the program. Closed Caption (CC) displays information at any position on the screen usually the program's dialog. Text displays information, usually at the bottom position and is used for a data service, generally not program related. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Special menu. Press ENTER or the RIGHT arrow button to activate the Special menu. Use the UP/DOWN arrows to choose Captions, then press ENTER or the Right arrow button. vcr cable dvd sat tv mode light source Use the UP/DOWN arrow buttons to make your caption selection. Your choices are: Off, Caption 1, Caption 2, Caption 3, Caption 4, Text 1, Text 2, Text 3 and Text 4. tv video front comp1 comp2 rgb enter Press EXIT to save and return to TV viewing or press the ENTER button to save and return to the previous menu. ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew PAGE 36 2/3/5 ratio mute vol power 1/3/4 2/3 skip play ff 206-03726 EZ Demo Shows you how to navigate the on-screen menus of your TV. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Special menu. vcr cable dvd sat tv mode light power source Press ENTER or the RIGHT arrow button to activate the Special menu. Use the UP/DOWN arrows to choose EZ Demo, then press ENTER or the RIGHT arrow button to activate EZ Demo. tv video front comp1 comp2 rgb enter Press exit button on the remote to stop EZ Demo. 2/3 ratio mute vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew 206-03726 1/3 2/3 skip play ff PAGE 37 Auto Clock Setup Sets the time automatically through the PBS broadcast signal. The PBS channel signal includes information for the correct time. Enter the local PBS channel number with the number buttons on your remote control. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Time menu. vcr cable dvd sat tv mode Press ENTER or the RIGHT arrow button to activate the Time menu. light power source Press ENTER or the RIGHT arrow button to activate the Auto Clock option then use the UP/DOWN arrow button to make your auto clock selection. • Use the number buttons to set the PBS channel. tv video front comp1 comp2 rgb enter 2/3/4 ratio mute • Time Zone - Lets you select the time zone of your viewing area. vol ch swap pipch- pipch+ pip • Daylight Savings - Lets you set Daylight Savings On or Off, depending on whether or not your viewing area observes Daylight Savings. menu flashbk surf • If you select Auto Clock, use the RIGHT arrow to choose On or off. Press EXIT to save and return to TV viewing or press the ENTER button to save and return to the previous menu. exit record stop pause rew freeze 2/3 skip play ff Your choices are saved when Auto Clock is set. PAGE 38 206-03726 Manual Clock Setup Enables you to enter the time using the number buttons on your remote control. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Time menu. vcr cable dvd sat tv mode Press ENTER or the RIGHT arrow button to activate the Time menu. light power source Use the UP/DOWN arrow button to choose Manual Clock, then press the RIGHT arrow to activate Manual Clock. Use the UP/DOWN arrows to make your Manual Clock selection. Your choices are: Year, Date and Time. tv video front comp1 comp2 rgb enter Use the number buttons to set the Year, Date and Time. Press EXIT to save and return to TV viewing or press the ENTER button to save and return to the previous menu. vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew 206-03726 2/6 ratio mute 1/3/4 2/3 skip play ff PAGE 39 TV Turn On Time Setup Lets you set an automatic turn on time for your TV. vcr cable dvd sat tv Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Time menu. mode light power source Press ENTER or the RIGHT arrow button to activate the Time menu. Use the UP/DOWN arrows to choose On Time then press the RIGHT arrow to activate On Time. Use the UP/DOWN arrows to choose On or Off. Use the number buttons to set the On Time options. Press EXIT to save and return to TV viewing, or press the ENTER button to save and return to the previous menu. tv video front comp1 comp2 rgb enter ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop PAGE 40 2/6 ratio mute vol You must set the current time before using on/off time function. pause rew 1/3/4 2/3 skip play ff 206-03726 TV Turn Off Time Setup Lets you set an automatic daily turn off time for your TV. vcr cable dvd sat tv mode Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Time menu. Press ENTER or the RIGHT arrow button to activate the Time menu. Use the UP/DOWN arrows to choose Off Time then press the RIGHT arrow to activate Off Time. light power source tv video front comp1 comp2 rgb enter Use the number buttons to set the Off Time options. 2/6 ratio mute Use the UP/DOWN arrows to choose On or Off. vol ch swap pipch- pipch+ pip Press EXIT to save and return to TV viewing, or press the ENTER button to save and return to the previous menu. menu flashbk surf freeze exit record stop pause rew 206-03726 1/2/3/4 2/3 skip play ff PAGE 41 Sleep Timer Setup Lets you select the amount of time before your TV automatically turns itself off. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the Time menu. Press ENTER or the RIGHT arrow button to activate the Time menu. Use the UP/DOWN arrows to choose Sleep Timer then press the RIGHT arrow to activate Sleep Timer. Use the UP/DOWN arrows to choose a preset turn off time. Press EXIT to save and return to TV viewing, or press the ENTER button to save and return to the previous menu. vcr cable dvd sat tv mode light power source tv video front comp1 comp2 rgb enter ratio mute vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew PAGE 42 1/3/4 skip play ff 206-03726 Parental Lock Setup Lets you block specific channels, ratings and other sources based on the blocking schemes. A password is required to gain access to this menu if the Lock System is activated. Press the MENU button on the remote control, then use the UP/DOWN arrow button to select the LOCK Menu. vcr cable dvd sat tv mode light power source Press ENTER or the RIGHT arrow button to activate the LOCK Menu. See the next page for more details on your blocking options. tv video front comp1 comp2 rgb enter ratio mute vol ch swap pipch- pipch+ pip menu flashbk surf freeze exit record stop pause rew 206-03726 skip play ff PAGE 43 Parental Lock Setup Continued Use the UP/DOWN arrows to choose from the following LOCK Menu options. • Lock On/Off: Activates or disables the blocking scheme you set up previously. • Set Password: Changes the password by inputting a new password twice. • Movie (MPPA): Blocks movies according to the movie ratings limit, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movie shown on TV, not TV programs, such as soap operas. vcr cable dvd sat tv mode light power • TV-PG (Children): Keeps children from watching certain TV programs among only the programs intended for children, according to the ratings limit. This rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - General menu, your children may view those programs. • TV-PG (General): Blocks certain TV programs that you and your family do not want to view, based on the ratings. source tv video front comp1 comp2 rgb enter ratio mute vol ch swap pipch- pipch+ pip • Block Channel: Blocks any channels that you do not want to view or that you do not want your children to watch. menu flashbk surf freeze • Aux. Block: Enables you to select a source for blocking among the source devices you have hooked up. exit record stop pause rew PAGE 44 skip play ff 206-03726 Parental Lock Setup Continued TV-Y7 (Directed to Older Children): This program is designed for children age 7 and above. TV-G (General audience): Most parents would find this program suitable for all ages. TV-PG (Parental guidance suggested): This program contains material that parents may find unsuitable for younger children. TV-14 (Parents strongly cautioned): This program contains some material that many parents would find unsuitable for children under 14 years of age. TV-MA (Mature audience only): This program is specifically designed to be viewed unsuitable for children under 17. by adults and therefore may be G - (General audiences): All ages admitted. PG - Parental guidance suggested: Some material may not be suitable for children. PG-13 - Parents strongly cautioned: Some material may not be appropriate for children under 13. R- (Restricted): Children under 17 requires accompanying parent or adult guardian. NC-17: No one 17 and under admitted. TV-Y (All Children): This program is determined to be appropriate for all children. X: Adult admitted only. NR: Not rated movie. 206-03726 PAGE 45 Programming the Remote The remote control of your HD receiver is a multibrand or universal remote control that can be programmed to operate most remote-controllable components of other manufacturers. Note that the remote control may not control all models of other brands. vcr cable dvd sat tv mode Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as the VCR and press the corresponding mode button (VCR) on the remote control while pointing at the component. Test the POWER and CH +/- buttons to see if the component responds properly. If not, the remote requires programming to operate the device. Turn on the component to be programmed. Then press the corresponding mode button on the remote control. Press the POWER button and the MUTE button simultaneously. Then the remote control is ready to program the code for the corresponding component. There are two ways to find the right code for the component. light power source tv video front comp1 comp2 rgb enter ratio mute vol swap pipch- pipch+ pip menu flashbk surf A. If you press the CH +/- buttons repeatedly, the code will change one at a time. Press the POWER button after each code change. If the right code is found, the device will turn off. B. Enter a code number using the number buttons on the remote. The right code numbers for the corresponding component can be found on the following pages. Again, if the code is correct, the device will turn off. ch freeze exit record stop pause rew skip play ff Press the EXIT button to store the program. Test the remote control functions to see if the component responds properly. If not, repeat from step 2. PAGE 46 206-03726 Programming Codes TVs Brand A MARK ADMIRAL AKAI AMPRO AMSTRAD ANAM AOC BLAUPUNKT CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES CXC DAEWOO DAYTRON DYNASTY DYNATECH ELECTROHOME EMERSON FISHER FUNAI FUTURETECH GE 206-03726 Codes 112 143 072 081 006 146 073 167 052 043 054 080 104 112 115 121 131 004 006 112 088 002 003 006 058 043 002 003 006 043 103 143 043 004 039 043 051 143 043 054 043 143 004 006 116 143 043 004 016 043 044 071 076 107 111 117 120 125 127 136 143 004 116 043 062 024 077 004 005 028 043 048 050 096 116 151 153 155 007 057 028 043 043 004 006 009 034 073 074 116 130 155 160 165 Brand GOLDSTAR 161 056 108 118 HALL MARK HITACHI 058 004 004 101 050 101 017 055 103 114 123 128 INFINITY INKEL JBL JCPENNY JENSEN JVC KEC KENWOOD KLOSS KMC KTV LG LODGENET LOGIK LUXMAN LXI MAGNAVOX 143 143 006 047 051 143 154 MARANTZ MATSUI MEMOREX METZ MGA MINERVA MITSUBISHI 008 056 091 144 161 MTC NAD NEC Codes 004 102 110 112 116 119 127 137 004 116 004 006 010 011 023 041 143 158 166 164 129 164 004 006 009 024 065 101 156 160 013 034 038 083 145 043 006 070 002 059 143 006 043 154 255 072 072 004 007 015 081 160 166 003 004 022 059 061 063 127 143 164 006 077 164 004 007 116 088 004 006 028 042 077 116 088 004 006 028 040 109 116 146 004 006 101 015 025 006 007 Brand 106 113 122 143 009 012 075 163 NIKEI ONKING ONWA OPTONICA PANASONIC PHILCO 008 030 143 PHILIPS 070 PIONEER PORTLAND PROSCAN 143 PROTON QUASAR RADIO SHACK 052 164 006 060 064 160 164 RCA REALISTIC ROCTEC RUNCO SAMPO 072 SAMSUNG 024 049 SANYO 024 042 124 SCOTT SEARS 062 Codes 019 024 056 130 134 043 043 043 019 081 034 056 092 164 003 004 024 043 059 060 064 127 164 003 004 006 038 070 093 160 164 006 018 025 027 135 176 004 143 144 160 165 167 004 058 131 143 173 034 056 019 043 116 127 004 006 024 056 074 144 156 160 165 007 019 047 186 168 169 004 006 116 004 050 101 105 116 127 137 143 007 020 033 039 057 082 004 028 048 116 004 007 028 030 082 094 116 143 040 132 Brand Sharp SIEMENS SIGNATURE SONY 080 006 056 063 143 005 059 143 023 116 161 SOUNDESIGN SPECTRICON SSS SUPRE MACY SYLVANIA TANDY TATUNG TECHNICS TECHWOOD TEKNIKA 116 171 092 047 143 023 065 152 161 TELEFUNKEN TELERENT TERA TMK TOSHIBA 043 058 089 113 133 160 021 053 166 043 143 015 057 101 160 TOTEVISION UNIVERSAL VIDEO CONCEPTS VIDIKRON VIDTECH WARDS YAMAHA YORK YUPITERU ZENITH ZONDA Codes 004 014 022 028 081 143 175 088 072 041 070 085 126 147 185 003 004 043 116 112 004 043 002 003 004 044 059 063 064 127 140 164 081 056 062 034 080 004 002 003 006 024 031 043 077 101 143 037 046 087 072 172 004 116 007 015 040 051 101 138 143 008 009 146 174 004 116 004 008 019 028 061 063 072 074 143 164 004 006 004 116 043 001 072 095 103 112 019 029 170 079 139 028 006 060 116 160 084 004 028 072 103 086 030 062 009 060 064 116 073 157 016 PAGE 47 Programming Codes VCRs Brand AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO GOLDSTAR HARMAN KARDON HITACHI INSTANTREPLAY JCL JCPENNY JENSEN JVC PAGE 48 Codes 034 016 043 124 125 072 031 033 012 023 043 035 037 028 031 108 003 040 031 033 005 007 064 065 110 111 116 117 108 012 023 043 034 053 059 006 017 027 029 034 035 037 046 129 131 153 003 008 010 034 031 033 072 107 144 147 132 136 012 013 101 106 123 012 045 004 018 034 043 137 150 031 033 031 033 012 013 033 040 101 043 012 031 043 048 Brand 046 146 103 039 KENWOOD LG LLOYD LXI 129 033 135 041 010 108 112 119 039 025 031 036 101 138 009 063 109 020 114 026 063 015 066 033 050 MAGIN MAGNAVOX MARANTZ MARTA MATSUI MEI MEMOREX MGA MINOLTA MITSUBISHI MTC MULTITECH NEC NORDMENDE OPTONICA PANASONIC PENTAX PHILCO PHILIPS PILOT PIONEER PORTLAND PULSAR QUARTZ QUASAR RCA Codes 055 060 150 152 014 034 043 047 255 034 003 009 014 017 101 106 040 031 033 041 067 012 031 067 069 101 027 030 031 033 003 010 031 033 053 072 102 134 045 046 013 020 013 020 046 049 059 061 034 040 024 034 012 023 043 048 043 053 054 066 070 083 133 145 013 020 033 063 031 034 031 033 054 067 101 101 013 021 108 072 011 014 033 066 145 013 020 Brand 130 039 048 REALISTIC 013 034 034 068 033 RICO RUNCO SALORA SAMSUNG SANSUI 014 034 101 139 059 SANYO SCOTT SEARS 045 051 151 039 074 140 031 067 034 071 SHARP SHINTOM SONY SOUNDESIGN STS SYLVANIA 048 SYMPHONIC TANDY TATUNG TEAC TECHNICS TEKNIKA 075 THOMAS TMK TOSHIBA 033 Codes 034 040 062 063 109 140 145 147 003 008 014 031 034 040 054 101 058 148 014 032 040 104 105 109 112 115 120 125 022 043 135 003 007 014 102 017 037 129 131 003 008 010 013 017 020 042 073 101 031 054 024 003 009 052 056 058 076 078 149 034 013 031 033 059 067 034 010 034 039 043 034 039 031 033 019 031 034 101 034 006 008 013 047 059 112 131 041 107 144 010 033 053 Brands TOTEVISION UNITECH VECTOR RESEARCH VICTOR VIDEO CONCEPTS VIDEOSONIC WARDS YAMAHA 102 107 113 122 ZENITH Codes 040 101 040 012 048 012 034 040 003 013 024 031 034 040 054 131 012 034 043 001 034 056 058 080 101 046 017 033 053 039 048 072 048 010 134 112 009 014 031 081 149 031 057 077 034 043 070 033 042 082 206-03726 Programming Codes SAT Brand ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME EUROPLUS FUJITSU Codes 123 050 051 126 053 053 013 014 018 036 008 009 077 054 050 145 005 006 010 011 112 116 024 046 076 038 040 058 093 095 096 098 099 122 089 114 017 021 Brand 129 015 055 012 007 052 141 056 057 094 097 100 022 Codes 027 133 GENERAL INSTRUMENT 003 004 029 031 101 HITACHI 139 140 HOUSTON TRACKER 033 037 051 057 HUGHES 068 HYTEK 053 JANIEL 060 147 JERROLD 061 KATHREIN 108 LEGEND 057 LG 255 LUTRON 132 LUXOR 062 144 MACOM 010 059 064 065 MEMOREX 057 NEXTWAVE 028 124 NORSAT 069 070 PACE SKY SATELLITE 143 PANASONIC 060 142 PANSAT 121 134 016 059 039 104 Brand PERSONAL CABLE PHILIPS PICO PRESIDENT PRIMESTAR PROSAT RCA REALISTIC SAMSUNG SATELLITE SERVICE CO SCIENTIFIC ATLANTA SONY STARCAST SUPER GUIDE TEECOM 063 125 TOSHIBA UNIDEN Codes 117 071 105 019 102 030 110 072 066 106 043 074 123 028 035 057 085 032 138 103 041 020 124 023 026 087 088 107 130 002 127 016 025 043 044 048 049 079 080 101 135 Brand VIEWSTAR WINEGARD ZENITH Codes 115 128 146 001 081 082 083 084 091 120 Brand THOMPSON TOSHIBA YAMAHA ZENITH Codes 005 006 019 008 009 018 010 016 025 111 047 125 075 090 137 042 045 078 086 136 DVD Brand APEX DIGITAL DENON GE GOLDSTAR HARMAN KARDON JVC LG 206-03726 Codes 022 020 014 005 006 010 016 025 027 012 001 010 016 Brand MAGNAVOX MARANTZ MITSUBISHI NAD ONKYO PANASONIC Codes 025 013 024 002 023 008 017 003 009 Brand PHILIPS PIONEER PROCEED PROSCAN RCA SAMSUNG SONY Codes 013 004 026 021 005 006 005 006 011 015 007 PAGE 49 Programming Codes CATV Brand ABC ANTRONIK ARCHER CABLE STAR CENTURION CENTURY CITIZEN COLOUR VOICE COMBANO COMTRONICS DIAMOND EAGLE EASTERN ELECTRICORD GE GEMINI GI GOLDEN CHANNEL HAMLIN HITACHI HOSPITALITY JERROLD PAGE 50 Codes 003 004 042 046 053 014 005 007 024 026 092 007 007 065 090 080 081 019 030 023 020 030 057 062 032 072 008 022 054 052 074 030 049 050 052 055 070 077 002 003 Brand 039 052 014 LG M-NET MACOM MAGNAVOX MEMOREX MOVIE TIME NSC OAK 040 066 PANASONIC PARAGON PHILIPS 025 PIONEER 055 POST NEWS WEEK PRUCER PTS 004 PULSAR RCA Codes 008 009 052 069 255 037 033 010 012 079 001 028 032 015 028 071 073 016 031 053 044 047 001 006 012 020 065 090 034 051 063 076 016 059 011 048 072 073 001 047 010 074 064 038 037 013 085 052 071 074 Brand REGAL REGENCY REMBRANT RK SAMSUNG SCIENTIFIC ATLANTA SHERITECH SIGNAL SIGNATURE SL MARX SPRUCER STARCOM STARGATE SYLVANIA TADIRAN TANDY TEXSCAN TOCOM TOSHIBA UNIKA UNITED CABLE UNIVERSAL Codes 049 050 057 025 091 030 068 003 011 042 043 046 022 030 052 030 047 078 002 004 009 008 030 067 030 017 029 067 039 040 001 007 014 004 053 005 007 024 026 Brand VIEWSTAR ZENITH Codes 032 035 012 015 018 086 087 088 089 001 060 093 041 045 008 056 024 014 027 206-03726 Maintenance Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new Entertainment Machine. Be sure to turn the power off and pull out the power cord before you begin any cleaning. SCREEN CLEANING 1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen. 2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your Entertainment Machine. CABINET CLEANING 1. Use a soft cloth with a mild soap solution to wipe the cabinet. 2. Rinse the cloth and wipe the cabinet again. 3. Let the cabinet air-dry before turning the Entertainment Machine on. WOOD CABINETS Use a quality wood cleaner and polish. This will protect the Entertainment Machine from dirt and dust, as well as keep the cabinet looking new. EXTENDED ABSENCE If you leave your Entertainment Machine dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges. If you use an off-air antenna, you may also want to disconnect it from the back of your Entertainment Machine before leaving. 206-03726 PAGE 51 Maintenance continued PICTURE INTERFERENCE Even though you may be getting cable, the signal may be weak, which means the quality of your picture may suffer due to other factors. If there are problems with the image on your Entertainment Machine, consult the Troubleshooting guide on the following pages. You may also want to contact your cable service provider to determine if the problem is from the cable service. VIDEO GAMES AND OTHER FIXED-PATTERN DISPLAYS If you use your Entertainment Machine to play video games or for other uses that have single, fixed images, such as a photo-CD player, you should avoid setting the Brightness level too high. If static images, like network identification patterns, are left sitting for too long, they can leave a permanent impression on the picture tube. You can reduce the chance of this happening by limiting the amount of time you use the fixed-image display, and by reducing the contrast and brightness levels. If you unplug your Entertainment Machine, you may have to reset the clock using the Time menu described earlier. PAGE 52 206-03726 Troubleshooting Some quick and easy tips to fixing problems yourself. SYMPTOMS SOLUTIONS Snowy picture and unclear sound. • • • • • • Multiple images or ‘ghost shadows.’ Check your antenna connection or location. Check your cable input. Check to see if the TV/VCR button on your VCR has the TV selected. Check your antenna direction and/or location. Check your cable input. Make sure the cable from your antenna to your Entertainment Machine is properly connected. Interference: Sharp lines across the screen and unclear sound. The following may cause image problems or distortion: Electrical appliances, powerful lights, cars, trucks; computers or portable phones; medical equipment • If possible increase the distance between your Entertainment Machine and the offending appliance. Or shut one of them off. Normal picture but no sound. • Check volume levels. • Make sure the TV is not Muted. • Try another channel. The problem may be the broadcast, not your Entertainment Machine. • Are the Audio A/V cables properly installed? • Are the wires for external speakers (if you have external speakers) properly installed? • Make sure your speakers turned on under the Audio menu. • If your audio mode is set to SAP, that channel may not have a SAP program. No picture and unclear sound. • Are you in TV or cable tuning mode, and should be in the other? • Make sure output channels on all A/V equipment are on the same channel (3 or 4). • Check that all connections are tight. No picture and no sound. • Is the AC power plugged in? • Check that your AC power outlet works. (Test it by plugging in something else or try another plug.) • Make sure your brightness and audio controls are set properly. • Try another channel. The problem may be with the broadcast. No color, but the sound is O.K. • Check the color control in the Video menu. • Try another channel. The problem may be with the broadcast. Picture has a big black box on it, but the sound is O.K. • The CC (closed caption) option may be in Text mode. Select Caption 1, or OFF in the Captions/Text menu. Picture has two horizontal black bars, one on top and one on bottom. • Your program is in letterbox. This means that the shape of your TV is a square, but the program is a rectangle. Think of the bars as empty space the program doesn’t fill; not picture that’s blocked out. Because this format is a direct representation of film as you see it in the movies, you are actually seeing MORE of the program when you see those bars. Missing Secret code • If you forget the secret code, press the remote control Button ‘7’, ‘7’, ‘7’ and ‘7’ when the display asks you to enter the secret code. 206-03726 PAGE 53 Troubleshooting, cont’d Remote control doesn’t work. Menu options can’t be changed or selected. No picture or sound when any non-cable source is selected. Weak or no Stereo Sound when using a stereo VCR. The PIP inset is black or lacks contrast. The PIP inset is “snow” when the source is Antenna 1. Time is incorrect. PAGE 54 • Make sure the batteries are fresh and installed properly. • Try unplugging your Entertainment Machine for a few minutes, then plug it back in. • Check to see if the source equipment has been turned on. • Make sure that the connections are secure on the back of your Entertainment Machine and on the source equipment. • Check to see if all the connections are secure. • Look in the Audio mode menu to see if all the settings are correct. • You are using channel 3 or 4 to view your VCR. No stereo sound is present under that decision. • • • • Check to be sure that the PIP source is turned on. You might want to adjust the PIP picture settings under the PIP menu. Check that all the wires are connected properly. Check to see if your input source for PIP is set correctly. •Look to see if the TV/VCR button on your VCR has the TV selected or change the PIP to another source. • Make sure the time was set initially. Probably power was lost. 206-03726 Glossary A list of definitions for some of the words found in this guide. 206-03726 75 OHM RF CABLE The round cable that comes from an off-air antenna or cable service provider. Each end looks like a hex shaped nut with a wire sticking through the middle, and it screws onto the threaded jack on the back of your TV. A/V CABLES Audio/Video cables. Three cables - Right audio (red), Left audio (white), and Video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality picture and sound from other A/V devices. A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television). ADD This function lets you add new channels to the channel list in memory that you’ll scroll through when using your remote. AMPLIFIER An external device that amplifies sound from a television, CD player, VCR, DVD or other A/V device. ANALOG TV Traditional method of representing a television signal as a replica (analog) of the original picture and sound. ANTENNA The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible for your home to be using an antenna. ASPECT RATIO The ratio of the horizontal dimension to the vertical dimension of a picture. Standard television in the U.S. today is generally transmitted and displayed in a 4:3 aspect ratio. High-Definition television will normally be formatted in a wider aspect ratio, assumed to be 16:9. CAPTIONS A form of subtitling that writes out the dialog for your program on the screen. CONVERGENCE This option lets you correct for color separation in your picture. DELETE This function lets you remove channels that you don’t watch from the channel list in memory. DIGITAL TV A new method of representing television signal as a series of binary numbers (1s and 0s). This method allows for the signal to be manipulated to eliminate redundancy to dramatically increase picture and sound quality. DOLBY DIGITAL Dolby Digital Cinema Sound is made possible by a new digital coding technique called Dolby AC-3. Dolby AC-3 produces high-quality, 5.1 channel surround sound which is six discrete separate channels for a full range of sound. Each channel can carry a different signal simultaneously (front center, front left, front right, surround left, surround right and subwoofer). INPUT Refers to the jack that receives a signal into the TV, VCR or other A/V device. PAGE 55 Glossary continued A list of definitions for some of the words found in this guide. JACK A connection on the back of a TV, VCR, or any other A/V device. This includes the RF jacks and the Audio/Video jacks that are color-coded. MODE The mode determines the type of device (TV, VCR, Cable, Aux) that the remote is controlling; remote operating mode. MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker all the speakers play the same audio. OUTPUT Refers to the jack that sends a signal out of a VCR, DVD, or other A/V device. PIP This is the most common way to refer to the Picture-In-Picture (PIP) option. PIP SNAPSHOT Press FREEZE button to capture and freeze sub picture in PIP or split mode. Press PIP button to enter PIP mode from another channel. Press EXIT button to remove PIP from the screen. SECOND AUDIO Second Audio Programming (SAP) is another, separate, audio channel available with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French. PROGRAMMING/SAP SIGNAL Picture and sound traveling through cable, or on the air, to your television screen. SOURCE The term for the equipment that provides audio and video information to your Entertainment Machine. Antenna, VCR, DVD players, or Cable Boxes are examples of sources. STEREO SOUND Stereo (stereophonic) sound refers to audio that’s divided into right and left sides. SURF This function created a customized list of your favorite channels. You can access this group of channels with the surf button on the remote by pressing Surf repeatedly. TEXT Arbitrary text not related to the program. TUNER Any device that picks up broadcast signals and turns them into picture and sound. PAGE 56 206-03726 Product Specifications Specifications Power requirements Number of inputs/outputs 120V, 60 Hz Video (In) 1 Vp-p, 75 ohms unbalanced, sync negative S Video (In) S Video (Out) Y: 1 Vp-p, 75 ohms unbalanced, sync negative C: 0.280 Vp-p (burst signal), 75 ohms Audio (In) Center Mode (In) 500 mVrms (100%) modulation), Impedance: 47 kilohms Audio out More than 408 mVrms at the maximum volume setting (variable) More than 408 mVrms (fix) Impedance (output): 2 kilohms Component input Y: 1.0 Vp-p, 75 ohms w/sync PB: 0.7 Vp-p, 75 ohms PR: 0.7 Vp-p, 75 ohms PC/DTV Inputs 15 pin Sub “D” Female Speaker output (W) 15W x2 Power consumption (W) In use (max.) 230W In standby 3W Weight (lbs) 145.1 TV Television system American TV Standard, NTSC, ATSC with STB Channel coverage VHF: 2 - 13 UHF: 14 - 69 CATV: 1 - 125 Antenna 75 ohm external terminal for VHF/UHF Screen Size 60” Width Supplied accessories Remote control, batteries 2 size AA (Alkaline battery), IR-Extender Screen Aspect Ratio 16 x 9 LCD Panel Size 1.21 inch 206-03726 Copyright 2002, Zenith Electronics Corporation PAGE 57 Notes PAGE 58 206-03726 Notes 206-03726 PAGE 59 Your Zenith Warranty Service Labor: During a period of one year from effective warranty date, Zenith will provide service labor when needed, as a result of manufacturing defects. Parts: New or remanufactured replacements for factory-defective parts will be supplied by Zenith for one year from effective warranty date (color picture tubes—two years). Such replacement parts are warranted for the remaining portion of the original warranty period. Any repair may require that the D60WLCD be returned to Zenith. Zenith maintains a limited inventory of replacement or loaner D60WLCDs for repair purposes, and a replacement or loaner unit may not be immediately available at the time your D60WLCD requires repair. Not Covered: This warranty covers manufacturing defects and does not cover installation, adjustment of customer controls, installation or repair of antenna systems, cable converters or cable company-supplied equipment; it also does not cover damage due to misuse, abuse, negligence, acts of God or other causes beyond the control of Zenith. Any alteration of the product after manufacture voids this warranty in its entirety. THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND ZENITH SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES OF ANY KIND, INCLUDING LOST REVENUES OR PROFITS IN CONNECTION WITH THIS PRODUCT. This warranty is limited to the operation of the product in compliance with the Sarnoff bit-streams and with the listed compatible products. The D60WLCD has been designed to be compatible with many of the operating and software protocols which may ultimately be used in digital or high-definition television and which are still being established or refined by third parties. The D60WLCD may have limited capabilities with any such protocols designated after the date of its actual manufacture. Effective Warranty Date: Operating Guide: Antenna: Important: Warranty Service: Warranty begins on the date of sale of D60WLCD. For your convenience, keep the dated bill of sale or delivery ticket as evidence of the purchase date. Read your Operating Guide carefully so that you will understand the operation of your set and how to adjust the customer controls. Reception problems caused by inadequate antenna or faulty antenna connections are the owner’s responsibility. Product Registration—Please fill out and mail your Product Registration Card. It is imperative that Zenith know how to reach you promptly if we should discover a safety problem that could affect you. For warranty service information, contact Zenith. Parts and service labor that are Zenith’s responsibility will be provided without charge. Other service is at the owner’s expense. If you have any problem in obtaining satisfactory warranty service, call or write the Zenith Response Center below. You must provide the model number, serial number and date of purchase or date of original installation. ZENITH Service Zenith Customer Information Center 201 James Record Rd., Building 3, Huntsville, AL 35824 Telephone (256) 772-1515 Mon-Fri, 7:00 a.m.-8:00 p.m. CST Sat. 8:00 a.m.-5:00 p.m. CST www.zenith.com Digital TV Hotline: 1-847-391-7000 ZENITH FACTORY OWNED SERVICE CENTERS 801 E. Roosevelt Rd Lombard, IL 60148 (630) 705-2830 201 James Record Rd. Building 4 Huntsville, AL 35824 (256) 774-4025 Home & Carry-in Service Television/VCR Parts and Accessories PTV/Camcorders Service Hours: M-F 8-5 Will accept UPS Shipments © Copyright 2001, Zenith Electronics Corporation P/N : 3828VA0220H(AB00EA) 206-03726
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Creator : Microsoft PowerPoint - [G.User's Manual] Create Date : 2002:03:13 16:22:45 Title : G.User's Manual Author : Administrator Producer : Acrobat PDFWriter 4.0 for Windows NT Modify Date : 2002:03:14 13:58:35-05:00 Page Count : 61EXIF Metadata provided by EXIF.tools