LG Electronics USA T1910BU LCD MONITOR User Manual G User s manual

LG Electronics USA LCD MONITOR G User s manual

Users Manual

  Order Number  : GETEC-C1-10-036  FCC Part 15 subpart B Test Report Number  : GETEC-E3-10-016  Page 1 / 1  EUT Type: LCD Monitor FCC ID.: BEJT1910BU   APPENDIX G : USER’S MANUAL
OWNER’S MANUALLCD TOUCH MONITOR LCD TOUCH MONITOR MODELST1710BT1910Bwww.lge.comPlease read this manual carefully before operatingyour set and retain it for future reference.ENGLISH
A1This unit has been engineered and manufactured to ensure your personal safety,however improper use may result in potential electrical  shock or fire hazards. Inorder to allow the proper operation of all safeguards incorporated in this display,observe the following basic rules for its installation, use, and servicing.On SafetyUse only the power cord supplied with the unit. In case you use another powercord, make sure that it is certified by the applicable national standards if not beingprovided by the supplier. If the power cable is faulty in any way, please contact themanufacturer or the nearest authorized repair service provider for a replacement.The appliance coupler is used as the disconnect device.Please make sure the device is installed near the wall outlet to which it isconnected and that the outlet is easily accessible.Operate the display only from a power source indicated in the specifications of thismanual or listed on the display. If you are not sure what type of power supply youhave in your home, consult with your dealer.Overloaded AC outlets and extension cords are dangerous. So are frayed powercords and broken plugs. They may result in a shock or fire hazard. Call yourservice technician for replacement.As long as this unit is connected to the AC wall outlet, it is not disconnected fromthe AC power source even if the unit is turned off.Do not Open the Display:There are no user serviceable components inside. There are Dangerous High Voltages inside, even when the power is OFF. Contact your dealer if the display is not operating properly.To Avoid Personal Injury :Do not place the display on a sloping shelf unless properly secured.Use only a stand recommended by the manufacturer.Do not drop an object on or apply impact to the product. Do not throw any toysor objects on the product screen. It can cause injury to human, problem to product and damage the display.  To Prevent Fire or Hazards:Always turn the display OFF if you leave the room for more than a short periodof time. Never leave the display ON when leaving the house.Keep children from dropping or pushing objects into the display's cabinetopenings. Some internal parts carry hazardous voltages.Do not add accessories that have not been designed for this display.When the display is to be left unattended for an extended period of time, unplugit from the wall outlet.In the presence of thunder and lightning, never touch the power cord and signalcable because it can be very dangerous. It can cause electric shock. Important Precautions
Important PrecautionsOn InstallationDo not allow anything to rest upon or roll over the power cord, and do not placethe display where the power cord is subject to damage.Do not use this display near water such as near a bathtub, washbowl, kitchensink, laundry tub, in a wet basement, or near a swimming pool.Displays are provided with ventilation openings in the cabinet to allow the releaseof heat generated during operation. If these openings are blocked, built-up heatcan cause failures which may result in a fire hazard. Therefore, NEVER:Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.Place the display in a built-in enclosure unless proper ventilation is provided.Cover the openings with cloth or other material.Place the display near or over a radiator or heat source.Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,mar, or damage the Active Matrix LCD permanently.Do not press the LCD screen with your finger for a long time as this may causesome afterimages.Some dot defects may appear as Red, Green or Blue spots on the screen.However, this will have no impact or effect on the display performance. If possible, use the recommended resolution to obtain the best image quality foryour LCD display. If used under any mode except the recommended resolution,some scaled or processed images may appear on the screen. However, this ischaracteristic of the fixed-resolution LCD panel.Leaving a fixed image on the screen for a long time may cause damage to thescreen and cause image burn-in. Make sure to use a screen saver on the product. Burn-in and related problems are not covered by the warranty on this product. Do not shock or scratch the front and sides of the screen with metallic objects. Otherwise, it may cause damage to the screen. Make sure the panel faces forward and hold it with both hands to move. If you drop the product, the damaged product can cause electric shock or fire. Contact an authorized the service center for repair. Avoid high temperatures and humidity. A2
A3Important PrecautionsOn CleaningUnplug the display before cleaning the face of the display screen.Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the displayscreen because over-spraying may cause electrical shock.When cleaning the product, unplug the power cord and scrub gently with a softcloth to prevent scratching. Do not clean with a wet cloth or spray water orother liquids directly onto the product. An electric shock may occur. (Do not usechemicals such as benzene, paint thinners or alcohol) Spray water onto a soft cloth 2 to 4 times, and use it to clean the front frame;wipe in one direction only. Too much moisture may cause staining.  On RepackingDo not throw away the carton and packing materials. They make an idealcontainer in which to transport the unit. When shipping the unit to anotherlocation, repack it in its original material.On DisposalThe fluorescent lamp used in this product contains a small amount of mercury.Do not dispose of this product with general household waste.Disposal of this product must be carried out in accordance to the regulations ofyour local authority.
A4Accessories!!! Thank for selecting LGE products !!! Please make sure the following items are included with yourmonitor. If any items are missing, contact your dealer.User's Guide/Cards Power Cord15-pin D-Sub Signal Cable(To set it up, this signal cable maybe attached to  this product beforeshipping out.)NOTEThis accessories may look different from those shown here.User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores tomaintain standard compliance for the product.USB CableTouch Driver CD
Basic Adjustments of the StandA51. Adjust the angle of the panel as follows.How to adjust the angle of the panelTilt Range : T1710B -> 14˚ to 66˚T1910B -> 14˚ to 68˚14˚ 66˚(68˚)The state which the stand locking handle is releasedThe state which the stand locking handle is lockedDo not push the stand with basicadjustment to the direction of thepanel. The product may fall downto hurt people, or cause productdisorder or screen damage.After installing the monitor, adjust the angle as follows.Basic Adjustment Push back the panel to the end, and use from the point that it automatically returns.2. After adjusting the angle of the panel for convenience, lock with the locking handle to prevent the product from moving.PanelStand
A6Using the Computer1. Make sure to turn off the computer and  product. Connect the cable as below sketch mapform to .12. Press        button on the front switch panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' is executed automatically.2Connecting the DisplayABConnect Dsub Cable (PC)Connect Dsub Cable (Mac)NOTE‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the userconnects the monitor for the first time, this function automatically adjusts the display to optimal settings for individualinput signals. ‘AUTO/SET’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tiltedscreen while using the device or after changing screen resolution, press the AUTO/SET function button to improveresolution. NOTEThis is a simplified representation of the rear view.This rear view represents a general model; your display may differ from the view as shown.Wall-outlet typePower Cord Analog signalD-subMac adapterFor Apple Macintosh use, a  separate plug adapter isneeded to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin2 row connector.
Connecting the DisplayA7To Use Touch ScreenInstall the Driver CD provided.1) Insert Touch Screen Driver CD into PC CO-ROM.2) After completing the driver installation, connect the USB cable for the touch screen.3) Please refer to the Touch Screen CD provided separately for detailinstallations. * The software drivers support the following Microsoft Windows operating systems: Windows 98, Windows 2000, XP, VISTA(32bit, 64bit).NOTEWhen you lose Driver CD or want to update the program, please refer tohttp://www.lge.com.< USB cable for the touch screen>AnalogsignalD-subPower CordTouch ScreenUSB CableTouchScreen USB CableNOTEYour purchased product and its accessories may look different from the itemsillustrated in this manual.
A8Control FunctionControl Panel FunctionsMENU ButtonUse this button to enter or exit from the On Screen Display.OSD LOCKED/UNLOCKEDThis function allows you to lock the current control settings, sothat these settings are not inadvertently changed. To lock theOSD settings, press and hold the MENU button for severalseconds. The message "OSD LOCKED" appears.You can unlock the OSD settings at any time bypushing the MENU button for several seconds. Themessage "OSD UNLOCKED" appears.Front Panel Controls
A9Control Panel FunctionsThis Indicator lights up as blue when the display isoperating normally(On Mode). If the display is inSleep Mode (Energy Saving), this indicator changesto flicker.Use this button to turn the display on or off.Power ButtonPower IndicatorUse this button to select an icon in the On ScreenDisplay.AUTO/SETButtonAUTO IMAGE ADJUSTMENTWhen adjusting your display settings, always pressthe AUTO/SET button prior to entering the OnScreen Display(OSD). This will automatically adjustyour display image to the ideal settings for thecurrent screen resolution size (display mode).The best display mode is:T1710B: 1280 x 1024T1910B: 1280 x 1024ButtonsUse these buttons to select or adjust functions in the OnScreen Display.For more information, refer to page A16.Control Function
A10On Screen Display (OSD) Control AdjustmentScreen AdjustmentMaking adjustments to the image size, position and operating parameters ofthe display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls.The following section is an outline of the available adjustments and selectionsyou can make using the OSD.To make adjustments in the On Screen Display, follow these steps:Press the MENU Button, then the main menu of the OSD appears.To access a control, use the       or      Buttons. When the icon you wantbecomes highlighted, press the AUTO/SET Button.Use the     /       Buttons to adjust the image to the desired level. Use theAUTO/SET Button to select other sub-menu items.Push the MENU Button once to return to the main menu to select anotherfunction. Push the MENU Button twice to exit from the OSD.NOTEAllow the display to stabilize for at least 30 minutes before making image adjustments.
A11NOTEThe order of icons may differ depending on the model (A11~A16 ).On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment,and setting menus.
A12Menu NameOn Screen Display(OSD) Selection and Adjustment NOTEOSD (On Screen Display) menu languages on the monitor may differ from the manual.You were introduced to the procedure of selecting and adjusting an itemusing the OSD system.  Listed below are the icons, icon names, and icondescriptions of the all items shown on the Menu.Press the MENU Button, then the main menu of the OSD appears.Menu NameMain MenuButton TipMENU        : Exit: Adjust (Decrease/Increase)SET        : Enter: Select another sub-menu: Restart to select sub-menuSub-menusIcons
A13On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionBRIGHTNESSCONTRAST GAMMATo adjust the brightness of the screen. To adjust the contrast of the screen.Set your own gamma value. : -50/0/50On the monitor, high gamma valuesdisplay whitish images and low gammavalues display high contrast images.PICTUREPRESETREDGREENBLUE• sRGB: Set the screen color to fit theSRGB standard colorspecification.• 6500K: Slightly reddish white.• 9300K: Slightly bluish white.Set your own red color levels.Set your own green color levels.Set your own blue color levels.COLORMENU : Exit: Decrease: IncreaseSET : Select another sub-menuMENU : Exit: Decrease: IncreaseSET : Select another sub-menu
A14On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionCLOCKPHASESHARPNESSTo minimize any vertical bars orstripes visible on the screenbackground.The horizontal screen size will alsochange.To adjust the focus of the display. This item allows you to removeany horizontal noise and clear orsharpen the image of characters.To adjust the clearness of thescreen.TRACKINGMENU : Exit: Decrease: IncreaseSET : Select another sub-menuHORIZONTALVERTICALTo move image left and right.To move image up and down.
A15Restore all factory default settings except"LANGUAGE." Press the       ,        buttons to reset immediately.On Screen Display(OSD) Selection and Adjustment Main menu Sub menu DescriptionIf this does not improve the screen image, restore the factory default settings. If necessary, perform the white balance function again. SETUPTo choose the language in which thecontrol names are displayed.To adjust position of the OSD windowon the screen.LANGUAGEOSDPOSITIONWHITEBALANCEFACTORYRESETIf the output of the video card is differentthe required specifications, the colorlevel may deteriorate due to videosignal distortion. Using this function, thesignal level is adjusted to fit into thestandard output level of the video cardin order to provide the optimal image.Activate this function when white andblack colors are present in the screen.   POWERINDICATORUse this function to set the powerindicator on the front side of the monitorto ON or OFF.If you set OFF, it will go off. If you set ON at any time, the powerindicator will automatically be turned on.MENU : Exit: Adjust: AdjustSET : Select another sub-menu
A16On Screen Display(OSD) Selection and Adjustment IconsMenu NameSub-menu NameMain menu Sub menu DescriptionMOVIEINTERNETNORMALDEMOSelect the                  button at the bottom left of the monitor, then the OSD screen willappear.INTERNET: For text images (Word processing etc.)MOVIE: For animation images in videos or movies This is under normal operating conditions.This is just for advertising to customer in theshops. It’s setting is same with Movie mode andscreen is divided by half.This feature lets you easily select the best desiredimage condition optimized to the environment(ambient illumination, image types etc).USERThe user can directly adjust ACE and RCM. You can save or restore the adjusted value evenwhen using a different environment. MENU : Exit: Decrease: IncreaseAUTO/SET: Select another sub-menuTo adjust the USER sub-menu function,press the AUTO/SET Button.• ACE (Adaptive Clarity Enhancer): Selects the clarity mode.Not appliedWeak clarity and luminosity contrast. Strong clarity and luminosity contrast. Not appliedGreen enhance Flesh toneColor Enhance• RCM (Real Color Management): Selects the color mode.
A17TroubleshootingNo image appearsCheck the following before calling for service.No image appearsDo you see a "OSD LOCKED" message on the screen?●Is the power cord of thedisplay connected?●Is the power indicatorlight on?●Is the power on and thepower indicator blue orgreen?●Is the power indicatorflickering?●Do you see an "OUT OFRANGE" message onthe screen?●Do you see a "CHECKSIGNAL CABLE"message on thescreen?• Check and see if the power cord is connectedproperly to the power outlet.• Press the Power button.• Adjust the brightness and the contrast.• If the display is in power saving mode, try movingthe mouse or pressing any key on the keyboard tobring up the screen.• Try to turn on the PC.• This message appears when the signal from thePC (video card) is out of horizontal or verticalfrequency range of the display. See the'Specifications' section of this manual andconfigure your display again.• This message appears when the signal cablebetween your PC and your display is notconnected. Check the signal cable and try again.• You can secure the current control settings,so that they cannot be inadvertently changed.You can unlock the OSD controls at any timeby pushing the MENU button for severalseconds: the message “OSD UNLOCKED”will appear.●Do you see “OSDLOCKED” when youpush MENU button?
A18TroubleshootingDisplay image is incorrect●Display Position isincorrect.●On the screenbackground, verticalbars or stripes arevisible.●Any horizontal noiseappearing in anyimage or charactersare not clearlyportrayed.• Press the AUTO/SET button to automaticallyadjust your display image to the ideal setting. If the results are unsatisfactory, adjust the imageposition using the H position and V position iconin the on screen display.• Press the AUTO/SET button to automaticallyadjust your display image to the ideal setting.If the results are unsatisfactory, decrease thevertical bars or stripes using the CLOCK icon inthe on screen display.• Press the AUTO/SET button to automaticallyadjust your display image to the ideal setting.If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display.• Check Control Panel --> Display --> Settingsand adjust the display to the recommendedresolution or adjust the display image to the idealsetting. Set the color setting higher than 24 bits(Color Quality).ImportantCheck Control Panel --> Display --> Settings and see if the frequency or theresolution were changed. If yes, readjust the video card to the recommendresolution.The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card    performance. In this case, please ask to the computer or the video card  manufacturer.
A19TroubleshootingDisplay image is incorrect●The screen color ismono or abnormal.●The screen blinks.• Check if the signal cable is properly connectedand use a screwdriver to fasten if necessary.• Make sure the video card is properly inserted inthe slot.• Set the color setting higher than 24 bits (ColorQuality) at Control Panel - Settings.• Check if the screen is set to interlace mode and ifyes, change it to the recommend resolution.Touch screen does not work.Install the touch screen driver on theinstallation CD bundled with the product.Make sure that the USB cable for touch screen is connected to your PC.Make sure your PC and accessories areUSB-enabled.●Did you install thetouch screendriver?
A20Specifications                                                                   T1710BDisplaySync InputVideo InputResolutionPlug&PlayPowerConsumptionDimensions&WeightTilt RangePower InputEnvironmentalConditionsStand BasePower cord NOTEInformation in this document is subject to change without notice.43.27 cm (17.0 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 43.27cm0.264 mm x 0.264 mm (Pixel Pitch)Horizontal Freq. 30 kHz to 83 kHz (Automatic)Vertical Freq. 56 Hz to 75 Hz (Automatic)Input Form Separate TTL SOG (Sync On Green) Signal Input 15 pin D-Sub ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm)Max VESA 1280 x 1024 @75 HzRecommend VESA 1280 x 1024 @60 HzDDC 2B0n Mode :       20 W(Typ.)Sleep Mode ≤1 WOff Mode ≤1 WWith Stand Without StandWidth 36.96 cm (14.55 inch) 36.96 cm (14.55 inch)Height 39.13 cm (15.41 inch) 31.51 cm (12.41 inch)Depth 18.48 cm (7.28 inch) 6.05 cm (2.38 inch)Net 3.90 kg ( 8.60 lb)Tilt 14˚ to 66˚AC 100-240V~ 50/60Hz 0.5A Operating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingAttached(    ), Detached ( O )Wall-outlet type or PC-outlet type
A21Specifications                                                                   T1910BNOTEInformation in this document is subject to change without notice.DisplaySync InputVideo InputResolutionPlug&PlayPowerConsumptionDimensions&WeightTilt RangePower InputEnvironmentalConditionsStand BasePower cord 48.19 cm (19.0 inch) Flat Panel Active matrix-TFT LCDAnti-Glare coatingVisible diagonal size: 48.19cm0.294 mm x 0.294 mm (Pixel Pitch)Horizontal Freq. 30 kHz to 83 kHz (Automatic)Vertical Freq. 56 Hz to 75 Hz (Automatic)Input Form Separate TTL SOG (Sync On Green) Signal Input 15 pin D-Sub ConnectorInput Form RGB Analog (0.7 Vp-p/ 75 ohm)Max VESA 1280 x 1024 @75 HzRecommend VESA 1280 x 1024 @60 HzDDC 2B0n Mode : 23 W(Typ.)Sleep Mode ≤1 WOff Mode ≤1 WWith Stand Without StandWidth 40.63 cm (16.00 inch) 40.63 cm (16.00 inch)Height 41.97 cm (16.52 inch) 34.45 cm (13.56 inch)Depth 18.48 cm (7.28 inch) 5.99 cm (2.36 inch)Net 3.86 kg (8.51 lb)Tilt 14˚ to 68˚AC 100-240V~ 50/60Hz 0.5A Operating ConditionsTemperature 10 ˚C to 35 ˚CHumidity 10 % to 80 % non-CondensingStorage ConditionsTemperature -20 ˚C to 60 ˚CHumidity 5 % to 90 % non-CondensingAttached(    ), Detached ( O )Wall-outlet type or PC-outlet type
A22SpecificationsDisplay Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz)1234567891011*1213640 x 350720 x 400640 x 480640 x 480800 x 600800 x 600832 x 6241024 x 7681024 x 7681152 x 8701152 x 9001280 x 10241280 x 102431.46931.46831.46937.50037.87946.87549.72548.36360.12368.68161.80563.98179.97670706075607575607575656075IndicatorOn ModeSleep ModeOff ModeblueBlue Color BlinkingOffLED ColorMODEPreset Modes (Resolution)* Recommend Mode
A23Installing the Wall mount plateThis monitor satisfies the specifications of the  Wall mount plate orthe interchange device.1. Place the monitor with its front facing downward on a soft cloth.2.Separate the head and the stand with the use of a screwdriver.Warning:You can hurt your finger.
A24Installing the Wall mount plateWall mount plate(Separate purchase)This is stand-type or wall mount type and isconnectable with Wall mount plate.Please refer to the installation guide for moredetails, which is provided when Wall mount plate ispurchased.Kensington Security SlotConnected to a locking cable that can bepurchased separately at most computerstores.3.Install the Wall mount plate.NOTEIf you intend to mount the set to a wall, attach Wall mounting interface (optional parts) tothe back of the set.When you install the set using the wall mounting interface (optionalparts), attach it carefully so it will not drop.1. Be sure to use screws and a wall mount that meet VESA standards.2. Using screws longer than those recommended might damage the product.3. Using screws that do not meet VESA standards might either damage the product or       result in it coming away from the wall. We will not be held responsible for any damage  resulting from failure to follow these instructions.4. VESA compatible only with respect to screw mounting interface dimensions and  mounting screw speci-fications.5. Please use VESA standard as below.      5-1) 784.8 mm (30.9 inch) and under               * Wall Mount Pad Thickness : 2.6 mm            * Screw :     4.0 mm x Pitch 0.7 mm x Length 10 mm     5-2) 787.4 mm (31.0 inch) and above             * Please use VESA standard wall mount pad and screws.
Make sure to read the Important Precautions before using the product.Keep the User’s Guide(CD) in  an  accessible place for furture reference.The model and  serial  number of the  SET  is located on the back and one side of the SET. Record it below should you ever need service.MODELSERIAL
Regulatory Information cont. FCC Compliance StatementThis equipment has been tested and found to complywithin the limits of a Class B digital device pursuant to Part15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in aresidential installation.This equipment generates, uses, and can radiate radiofrequency energy and if not installed and used inaccordance with the instructions, may cause harmfulinterference to radio communications. However, there isno guarantee that interference will not occur in a particularinstallation.If this equipment does cause harmful interference to radioor television reception (which can be determined byturning the equipment on and off), the user is encouragedto try to correct the interference by using one or more ofthe following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult the dealer or an experienced radio/TVtechnician for help.Caution: Changes or modifications not expressly approvedby the party responsible for compliance could void theuser's (or your) authority to operate the equipment. Onlyperipherals (digital input/output devices, terminals, printers,etc.) certified to comply with the Class B limits may beattached to this monitor. Operation with non-certifiedperipherals is likely to result in interference to radio and TV reception. Only shielded signal cables may be used withthis System.Canadian DOC NoticeThis Class B digital apparatus meets all requirements ofthe Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe Brespecte toutes les exigences du Règlement sur lematériel brouilleur du Canada.CE Conformity Notice (for Europe)Products with the “CE” Marking comply with the EMCDirective(89/336/EEC) and LOW VOLTAGE Directive(73/23/EEC) issued by the Commission of the EuropeanCommunity.Compiance with these directives implies conformity to thefollowing European Norms :•  EN 55022 ; Radio Frequency Interference•  EN 55024 ; Electromagnetic Immunity•  EN 61000-3-2 ; Power Line Harmonics•  EN 61000-3-3 ; Voltage Fluctuations•  EN 60950-1 ; Product SafetyLow Radiation Compliance (MPR II)This monitor meets one of the strictest guidelines availabletoday for low radiation emissions, offering the user extrashielding and an antistatic screen coating. Theseguidelines, set forth by a government agency in Sweden,limit the amount of emission allowed in the Extremely LowFrequency (ELF) and Very Low Frequency (VLF)electromagnetic range.01NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.NOTICEThe regulations are applied only to the products with theID LABEL indicating specific requirements.TCO'99 (TCO'99 applied model only)Congratulations!You have just purchased a TCO’99 approved and labelledproduct! Your choice has provided you with a productdeveloped for professional use. Your purchase has alsocontributed to reducing the burden on the environment andalso to the further development of environmentallyadapted electronics products.
Regulatory Information cont. 02Why do we have environmentally labelled computers?In many countries, environmental labelling has become anestablished method for encouraging the adaptation ofgoods and services to the environment. With the growingmanufacture and usage of electronic equipmentthroughout the world, there is a recognized concern for thematerials and substances used by electronic productswith regards to their eventual recycling and disposal. Byproper selection of these materials and substances, theimpact on the environment can be minimized.There are also other characteristics of a computer, such asenergy consumption levels, that are important from theviewpoints of both the work (internal) and natural (external)environments. Electronic equipment in offices is often leftrunning continuously, resulting in unnecessaryconsumption of large amounts of energy and additionalpower generation. From the standpoint of carbon dioxideemissions alone, it is vital to save energy.What does labelling involve?The product meets the requirements for the TCO’99scheme which provides for international and environmentallabelling of personal computers and/or displays. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of ProfessionalEmployees), Svenska Naturskyddsforeningen (The Swedish Society for Nature Conservation) andStatens Energimyndighet (The Swedish NationalEnergy Administration).Approval requirements cover a wide range of issues:ecology, ergonomics, emission of electrical and magneticalfields, energy consumption and electrical safety. Ecological criteria impose restrictions on the presence anduse of heavy metals, brominated and chlorinated flameretardants, and other substances. The product must beprepared for recycling and the manufacturing site(s) shallbe certified according to ISO14001 or EMAS registered.Energy requirements include a demand that the systemunit and/or display, after a certain period of inactivity,shall reduce its power consumption to a lower level in oneor more stages. The length of time to reactivate the systemunit shall be reasonable for the user.Labelled products must meet strict environmentaldemands, for example, in respect of the reduction ofelectrical and magnetical fields as well as work load andvisual ergonomics.Below you will find a brief summary of the ecologicalrequirements met by this product. The completeecological criteria document can be found at TCODevelopment’s website http://www.tcodevelopment.comor may be ordered from:TCO DevelopmentSE-114 94 STOCKHOLM, SwedenFax: +46 8 782 92 07Email : development@tco.seInformation regarding TCO’99 approved and labelledproducts may also be obtained athttp://www.tcodevelopment.comEcological requirementsFlame retardantsFlame retardants may be present in printed wiring boardlaminates, cables, and housings. Their purpose is toprevent, or at least to delay the spread of fire. Up to 30%by weight of the plastic in a computer casing can consist offlame retardant substances. Many flame retardantscontain bromine or chlorine, and these flame retardantsare chemically related to PCBs (polychlorinatedbiphenyls). Both the flame retardants containing bromineor chlorine and the PCBs are suspected of giving rise tohealth effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative*processes when not disposed of in accordance with strictstandards for disposal.TCO’99 requires that plastic components weighing morethan 25 grams shall not contain flame retardants withorganically bound bromine or chlorine. Flame retardantsare allowed in the printed wiring board laminates due tothe lack of commercially available alternatives.Cadmium**Cadmium is present in rechargeable batteries and in thecolour-generating layers of certain computer displays.TCO’99 requires that batteries, the colour-generatinglayers of display screens, and the electrical or electronicscomponents shall not contain any cadmium.Mercury**Mercury is sometimes found in batteries, relays andswitches. TCO’99 requires that batteries shall not containany mercury. It also demands that mercury is not presentin any of the electrical or electronics componentsassociated with the labelled unit. There is however one
Regulatory Information cont. 03exception. Mercury is, for the time being, permitted in theback light system of flat panel monitors as there today isno commercially available alternative. TCO aims onremoving this exception when a mercury free alternative isavailable.Lead**Lead can be found in picture tubes, display screens,solders and capacitors. TCO’99 permits the use of leaddue to the lack of commercially available alternatives, butin future requirements TCO Development aims atrestricting the use of lead._____________________________________________* Bio-accumulative is defined as substances which accumulate in living organisms.**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.TCO’03(TCO’03 applied model only)Congratulations!The display you have just purchased carries the TCO’03Displays label. This means that your display is designed,manufacturedand tested according to some of the strictest quality andenvironmental requirements in the world. This makes for ahigh performance product, designed with the user in focusthat also minimizes the impact on our natural environment.Some of the features of the TCO’03 Display requirements:Ergonomics•     Good visual ergonomics and image quality in order toimprove the working environment for the user and toreduce sight and strain problems. Importantparameters are luminance, contrast, resolution,reflectance, colour rendition and image stability.Energy•     Energy-saving mode after a certain time – beneficialboth for the user and the environment•     Electrical safetyEmissions•     Electromagnetic fields•     Noise emissionsEcology•     The product must be prepared for recycling and themanufacturer must have a certified environmentalmanagement system such as EMAS or ISO 14 001•     Restrictions onchlorinated and brominated flame retardants andpolymersheavy metals such as cadmium, mercury and lead.The requirements included in this label have beendeveloped by TCO Development in co-operation withscientists, experts, users as well as manufacturers all overthe world. Since the end of the 1980s TCO has beeninvolved in influencing the development of IT equipment ina more user-friendly direction. Our labelling system startedwith displays in 1992 and is now requested by users andIT-manufacturers all over the world.For more information, please visitwww.tcodevelopment.comInformation for Environmental PreservationLGE. announced the 'LG Declaration for a CleanerEnvironment' in 1994, and this ideal has served as aguiding managerial principle ever since. The Declaration isa foundation that has allowed us to undertakeenvironmentally friendly activities in careful considerationof economic, environmental, and social aspects.We promote activities for environmental preservation, andwe specifically develop our products to embrace theconcept of environment-friendly. We minimize the hazardous materials contained in ourproducts. For example, there is no cadmium to be found inour monitors.Information for recyclingThis monitor may contain parts which could be hazardousto the environment. It is important that this monitor berecycled after use.LGE. handles all waste monitors through anenvironmentally acceptable recycling method. There areseveral take-back and recycling systems currently inEnglish
Regulatory Information cont. 04operation worldwide. Many parts will be reused andrecycled, while harmful substances and heavy metals aretreated by an environmentally friendly method.If you want to find out more information about ourrecycling program, please contact your local LG vendor ora corporate representative of LG. We set our vision and policies on a cleaner world byselecting the issue of the global environment as a task forcorporate improvement. Please visit our website for moreinformation about our ‘green’ policies.http://www.lge.com/about/environment/html/Recycling.jspInformationen zur Erhaltung der UmweltIm Jahr 1994 verkündete LGE die 'LG Declaration for aCleaner Environment' (LG Erklärung für eine sauberereUmwelt). Seitdem dient dieses Ideal als führendes Prinzipdes Unternehmens. Diese Erklärung war die Basis für dieDurchführung von umweltfreundlichen Aktivitäten, wobei wirtschaftliche,umweltbezogene und soziale Aspekte in die Überlegungen mit einbezogen wurden.Wir fördern Aktivitäten zum Schutz der Umwelt und dieEntwicklung unserer Produkte ist darauf ausgerichtet,unserem Konzept bezüglich Umweltfreundlichkeit gerechtzu werden. Wir sind darauf bedacht, den Anteil der in unserenProdukten enthaltenen schädlichen Materialien zuminimieren. So ist in unseren Monitoren beispielsweisekein Kadmium zu finden.Informationen zum Thema RecyclingDieser Monitor enthält Teile, die umweltschädlich seinkönnen. Es ist unbedingt erforderlich, dass der Monitorrecycelt wird, nachdem er außer Dienst gestellt wurde.Bei LGE. werden alle ausrangierten Monitore in einemunter umweltbezogenen Aspekten geeigneten Verfahrenrecycelt. Augenblicklich sind weltweit mehrereRücknahme- und Recyclingsysteme im Einsatz. VieleTeile werden wieder verwendet und recycelt. SchädlicheSubstanzen und Schwermetalle werden durchumweltverträgliche Verfahren behandelt.Falls Sie mehr über unser Recyclingprogramm erfahrenmöchten, wenden Sie sich bitte an Ihren lokalen LG-Händler oder einen Unternehmensvertreter von LG. Wir richten unsere Firmenpolitik auf eine sauberereUmwelt hin aus, indem wir umweltspezifische Aspekte alswichtigen Punkt in die Weiterentwicklung unseresUnternehmens einfließen lassen. ZusätzlicheInformationen über unsere ‘grüne’ Firmenpolitik erhaltenSie auf unserer Website.http://www.lge.com/about/environment/html/Recycling.jspInformation sur la protection del’environnementLGE. a publié sa 'Déclaration en faveur d’unenvironnement plus propre' en 1994 et celle-ci est restée,depuis lors, un principe directeur de notre entreprise.Cette déclaration a servi de base à notre réflexion et nousa permis de prendre en compte à la fois les aspectséconomiques et sociaux de nos activités, tout enrespectant l’environnement.Nous encourageons les activités en faveur de lapréservation de l’environnement et c’est dans cet esprit que nous développons nos produits : nous réduisons auminimum les matières dangereuses qui entrent dans leurcomposition et l’on ne trouve pas de cadmium, parexemple, dans nos moniteurs.Information sur le recyclageCe moniteur peut contenir des composants qui présententun risque pour l’environnement. Il est donc important quecelui-ci soit recyclé après usage.LGE. traite les moniteurs en fin de cycle conformément àune méthode de recyclage respectueuse del’environnement. Nous reprenons nos produits et lesrecyclons dans plusieurs sites répartis dans le mondeentier. De nombreux composants sont réutilisés etrecyclés, et les matières dangereuses, ainsi que lesmétaux lourds, sont traités selon un procédé écologique.Si vous souhaitez plus de renseignements sur notreprogramme de recyclage, veuillez contacter votrerevendeur LG ou un l’un de nos représentants. Nous voulons agir pour un monde plus propre et croyonsau rôle de notre entreprise dans l’amélioration del’environnement. Pour plus de renseignements sur notrepolitique “verte”, rendez visite à notre site :http://www.lge.com/about/environment/html/Recycling.jspDeutschFrançais
05Regulatory Information cont. Informazioni per la tutela dell’ambienteLa LGE. ha annunciato nel 1994 la cosiddetta 'LGDeclaration for a Cleaner Environment' (Dichiarazione diLG a favore di un ambiente più pulito), un ideale che daallora funge da principio ispiratore della gestioneaziendale. La dichiarazione rappresenta il fondamento checonsente di intraprendere attività a favore dell'ambientetenendo conto degli aspetti economici, ambientali esociali.Noi della LG, promuoviamo attività a favore dellatutela dell'ambiente sviluppando appositamente i nostriprodotti per cogliere il concetto del rispetto dell’ambienteriducendo i materiali dannosi presenti nei nostri prodotti.Ad esempio nei nostri monitor non è presente il cadmio.Informazioni per il riciclaggioIl monitor può presentare componenti che potrebberorisultare eventualmente dannosi per l'ambiente. Èimportante che il monitor sia riciclato al termine del suoutilizzo.La LGE. gestisce tutti i monitor di rifiuto con un metodo diriciclaggio soddisfacente dal punto di vista ambientale. Intutto il mondo sono attualmente in funzione numerosisistemi di riciclaggio e recupero. I diversi componenti sonoriutilizzati e riciclati, mentre le sostanze dannose e i metallipesanti vengono trattati con un metodo rispettosodell’ambiente.Se si desiderano maggiori informazioni in merito alprogramma di riciclaggio, è consigliabile rivolgersi alproprio rivenditore LG o ad un rappresentante aziendaledella LG. Noi della LG impostiamo la nostra visione e le nostrepolitiche a favore di un mondo più pulito ponendo laquestione dell'ambiente dal punto di vista globale comeuna mansione rivolta al miglioramento della nostraazienda. Vi invitiamo a visitare il nostro sito internet perulteriori informazioni sulla nostra politica “verde”.http://www.lge.com/about/environment/html/Recycling.jspInformación para la conservación medioambientalLGE. presentó la 'Declaración para un entorno más limpiode LG' en 1994 y este ideal ha servido para guiar nuestrosprincipios empresariales desde entonces. La Declaraciónes la base que nos ha permitido llevar a cabo tareas querespetan el medio ambiente siempre teniendo en cuentaaspectos sociales, económicos y medioambientales.Promocionamos actividades orientadas a la conservacióndel medio ambiente y desarrollamos nuestros productosespecíficamente para que se ajusten a la filosofía queprotege el entorno. Reducimos al máximo el uso de materiales de riesgo ennuestros productos. Un ejemplo de ello es la ausenciatotal de cadmio en nuestros monitores.Información para el reciclajeEste monitor puede contener piezas que entrañen riesgosmedioambientales. Es importante reciclar este monitordespués de su utilización.LGE. trata todos los monitores usados siguiendo unmétodo de reciclaje que no daña al entorno. Contamoscon diversos sistemas de recuperación y reciclaje quefuncionan a nivel mundial en la actualidad. Es posiblereciclar y reutilizar muchas de las piezas, mientras que lassustancias dañinas y los metales pesados se tratansiguiendo un método que no perjudique al medioambiente. Si desea obtener más información acerca delprograma de reciclaje, póngase en contacto con suproveedor local de LG o con un representante empresarialde nuestra marca. Basamos nuestra visión y nuestras políticas en un mundomás limpio y para ellos optamos por un entorno globalcomo tarea principal de nuestra evolución como empresa.Visite nuestra página Web para obtener más informaciónsobre nuestras políticas ecológicas.http://www.lge.com/about/environment/html/Recycling.jspInformações relacionadas à preservaçãoambientalA LGE. anunciou a 'LG Declaration for a CleanerEnvironment' (Declaração da LG para um ambiente maislimpo) em 1994 e esse ideal tem servido desde entãocomo um princípio administrativo de orientação. ADeclaração é a base que nos tem permitido realizaratividades favoráveis ao ambiente com consideraçãoatenta aos aspectos econômicos, ambientais e sociais.Promovemos atividades de preservação ambiental edesenvolvemos nossos produtos para englobarItalianoEspanõlPortuguês
06Regulatory Information cont. especificamente o conceito de favorável ao ambiente. Reduzimos os materiais perigosos contidos em nossosprodutos. Por exemplo, não há cádmio em nossosmonitores.Informações relacionadas à reciclagemEste monitor pode conter peças que podem representarriscos ao ambiente. É importante que ele seja recicladoapós o uso.A LGE. cuida de todos os monitores descartados atravésde um método de reciclagem agradável ao ambiente. Hávários sistemas de devolução e reciclagem atualmenteem operação no mundo. Muitas peças serão reutilizadase recicladas e as substâncias nocivas e os metaispesados passarão por tratamento através de um métodofavorável ao ambiente.Para obter mais informações sobre nosso programa dereciclagem, entre em contato com seu fornecedor LGlocal ou com um representante corporativo da LG. Definimos nossa visão e nossas políticas relacionadas aum mundo mais limpo selecionando a questão doambiente global como uma tarefa de aprimoramentocorporativo. Visite nosso site para obter mais informaçõessobre nossas políticas de meio ambiente.http://www.lge.com/about/environment/html/Recycling.jspInformatie met betrekking tot het behoud vanhet milieuLGE. publiceerde in 1994 de 'LG Declaration for a CleanerEnvironment' (de LG-verklaring met betrekking tot eenschoner milieu). Deze verklaring en het ideaal van eenschoner milieu fungeren sindsdien als een bestuurlijkeleidraad voor onze onderneming. Op basis van dezeverklaring ontplooien wij milieuvriendelijke activiteiten,waarbij er zowel met sociale en economische aspecten,als met milieuaspecten zorgvuldig rekening wordtgehouden.Wij ondersteunen activiteiten die zijn gericht op hetbehoud van het milieu en wij houden bij het ontwikkelenonze producten specifiek rekening met de milieuvriendelijkheid van onze producten. Wij minimaliseren het gebruik van schadelijke stoffen inonze producten. Er wordt bijvoorbeeld geen cadmiumverwerkt in onze monitors.NederlandsInformatie met betrekking tot recyclingDeze monitor bevat materialen die schadelijk zoudenkunnen zijn voor het milieu. Het is belangrijk dat dezemonitor aan het einde van zijn levensduur wordtgerecycled.LGE. verwerkt alle afvalmonitors via een milieuvriendelijkerecyclingmethode. Hiervoor worden er momenteelwereldwijd verscheidene inname- en recyclingsystemengehanteerd. Een groot aantal onderdelen wordt opnieuwgebruikt en gerecycled, waarbij schadelijke stoffen enzware metalen volgens een milieuvriendelijke methodeworden verwerkt.Voor meer informatie over ons recyclingprogramma kunt ucontact opnemen met uw plaatselijke LG-vertegenwoordiger of een LG-vestiging. Onze visie en ons beleid met betrekking tot een schonerewereld vloeien voort uit het feit dat wij het milieu hebbenaangemerkt als een onderwerp dat speciale aandachtverdient binnen onze onderneming. Bezoek onze websitevoor meer informatie over ons 'groene' beleid.http://www.lge.com/about/environment/html/Recycling.jsp»ÌÙÓχˆËˇ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚¬ 1994 „Ó‰Û ÍÓÔÓ‡ˆËˇ LGE ÓÔÛ·ÎËÍÓ‚‡Î‡'ƒÂÍ·‡ˆË˛ LG ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚',ÍÓÚÓ‡ˇ Ò ÚÂı ÔÓ ÒÎÛÊËÚ ÓÒÌÓ‚Ì˚Ï ÔË̈ËÔÓÏÛÔ‡‚ÎÂÌˡ. Õ‡ ÓÒÌÓ‚Â ˝ÚÓÈ ‰ÂÍ·‡ˆËË Ï˚ ÒÏÓ„ÎËÔ‰ÔËÌˇÚ¸ ‰ÂÈÒڂˡ, Ó·ÂÒÔ˜˂‡˛˘Ë ·ÂÁÓÔ‡ÒÌÓÒÚ¸ ÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÔË ˝ÚÓωÓÎÊÌÓ ‚ÌËχÌË ˝ÍÓÌÓÏ˘ÂÒÍËÏ, ˝ÍÓÎӄ˘ÂÒÍËÏ ËÒӈˇθÌ˚Ï ‡ÒÔÂÍÚ‡Ï.Ã˚ ÒÚËÏÛÎËÛÂÏ ‰ÂˇÚÂθÌÓÒÚ¸ ÔÓ Óı‡ÌÂÓÍÛʇ˛˘ÂÈ Ò‰˚, Û‰ÂΡˇ ÓÒÓ·Ó ‚ÌËχÌËÂ‡Á‡·ÓÚÍ ̇¯ÂÈ ÔÓ‰Û͈ËË ‚ ÒÓÓÚ‚ÂÚÒÚ‚ËË ÒÍÓ̈ÂÔˆËÂÈ ˝ÍÓÎӄ˘ÂÒÍÓÈ ·ÂÁÓÔ‡ÒÌÓÒÚË. Ã˚ Ò‚Ó‰ËÏ Í ÏËÌËÏÛÏÛ ÒÓ‰ÂʇÌË ÓÔ‡ÒÌ˚ı‚¢ÂÒÚ‚ ‚ ̇¯ÂÈ ÔÓ‰Û͈ËË. Õ‡ÔËÏÂ, ‚ ̇¯ËıÏÓÌËÚÓ‡ı ‚˚ Ì ̇ȉÂÚ ͇‰Ïˡ.»ÌÙÓχˆËˇ ÔÓ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚›ÚÓÚ ÏÓÌËÚÓ ÏÓÊÂÚ ÒÓ‰Âʇڸ ÍÓÏÔÓÌÂÌÚ˚,ÍÓÚÓ˚ ÏÓ„ÛÚ Ì‡ÌÂÒÚË Û˘Â· ÓÍÛʇ˛˘ÂÈ Ò‰Â.Russian
07Regulatory Information cont. EPA(EPA applied model only)ENERGY STARis a set of power-saving guidelinesissued by the U.S. Environmental ProtectionAgency(EPA).NOM MARK (Mexico only)ÕÂÓ·ıÓ‰ËÏÓ ÛÚËÎËÁËÓ‚‡Ú¸ ÏÓÌËÚÓ ÔÓÒÎÂËÒÔÓθÁÓ‚‡Ìˡ.KÓÔÓ‡ˆËˇ LGE ÔÂÂ‡·‡Ú˚‚‡ÂÚ ‚Ò ·‡ÍÓ‚‡ÌÌ˚ÂÏÓÌËÚÓ˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍË ÔËÂÏÎÂÏÓ„ÓÏÂÚÓ‰‡ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚. œÓ ‚ÒÂÏÛ ÏËÛ‰ÂÈÒÚ‚Û˛Ú ÒËÒÚÂÏ˚ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ë ‚ÓÁ‚‡Ú‡ËÒÔÓθÁÓ‚‡ÌÌÓÈ ÔÓ‰Û͈ËË. ÃÌÓ„Ë ÍÓÏÔÓÌÂÌÚ˚·Û‰ÛÚ ‚ÚÓ˘ÌÓ ËÒÔÓθÁÓ‚‡Ì˚ Ë ÛÚËÎËÁËÓ‚‡Ì˚, ‚ ÚÓ‚ÂÏˇ Í‡Í ‚‰Ì˚ ‚¢ÂÒÚ‚‡ Ë ÚˇÊÂÎ˚ ÏÂÚ‡ÎÎ˚·Û‰ÛÚ Ó·‡·ÓÚ‡Ì˚ Ò ÔÓÏÓ˘¸˛ ˝ÍÓÎӄ˘ÂÒÍËÔËÂÏÎÂÏÓ„Ó ÏÂÚÓ‰‡.«‡ ·ÓΠÔÓ‰Ó·ÌÓÈ ËÌÙÓχˆËÂÈ ÔÓ Ì‡¯ÂÈÔÓ„‡ÏÏ ÛÚËÎËÁ‡ˆËË ÓÚıÓ‰Ó‚ Ó·‡˘‡ÈÚÂÒ¸ ÍÏÂÒÚÌÓÏÛ ÔÓÒÚ‡‚˘ËÍÛ ËÎË Ô‰ÒÚ‡‚ËÚÂβ ÍÓÔÓ‡ˆËË LG. Ã˚ ÓËÂÌÚËÛÂÏÒˇ ̇ Ó·ÂÒÔ˜ÂÌË ˝ÍÓÎӄ˘ÂÒÍÓÈ·ÂÁÓÔ‡ÒÌÓÒÚË, ÒÚ‡‚ˇ Ò· ˆÂθ˛ „ÎÓ·‡Î¸ÌÛ˛ Á‡˘ËÚÛÓÍÛʇ˛˘ÂÈ Ò‰˚. ƒÓÔÓÎÌËÚÂθÌÛ˛ ËÌÙÓχˆË˛Ó ̇¯ÂÈ ÔÓÎËÚËÍ ÔÓ Óı‡Ì ÓÍÛʇ˛˘ÂÈ Ò‰˚ ‚˚ÏÓÊÂÚ ̇ÈÚË Ì‡ ̇¯ÂÏ Ò‡ÈÚÂ:http://www.lge.com/about/environment/html/Recycling.jspAs an ENERGY STAR Partner LGE U. S.A.,Inc. has determined that this productmeets the ENERGY STAR guidelines forenergy efficiency.
08Regulatory Information cont. 1.When this crossed-out wheeled bin symbol is attachedto a product it means the product is covered by theEuropean Directive 2002/96/EC. 2.All electrical and electronic products should bedisposed of separately from the municipal wastestream via designated collection facilities appointed bythe government or the local authorities. 3.The correct disposal of your old appliance will helpprevent potential negative consequences for theenvironment and human health.4.For more detailed information about disposal of yourold appliance, please contact your city office, wastedisposal service or the shop where you purchased theproduct.Disposal of your old appliance1.Quando su un prodotto è riportato il simbolo di1.När den här symbolen med en överkryssadsoptunna på hjul sitter på en produkt innebär detatt den regleras av European Directive2002/96/EC.2.Alla elektriska och elektroniska produkter börkasseras via andra vägar än de som finns förhushållsavfall, helst via för ändamålet avseddauppsamlingsanläggningar som myndigheternautser.3.Om du kasserar din gamla apparat på rätt sättså bidrar du till att förhindra negativakonsekvenser för miljön och människors hälsa.4.Mer detaljerad information om kassering av dingamla apparat kan får av kommunen,renhållningsverket eller den butik där du köpteprodukten.1.Als het symbool met de doorgekruiste verrijdbareafvalbak op een product staat, betekent dit dathet product valt onder de Europese Richtlijn2002/96/EC.2.Elektrische en elektronische producten mogenniet worden meegegeven met het huishoudelijkafval, maar moeten worden ingeleverd bijspeciale inzamelingspunten die door de lokale oflandelijke overheid zijn aangewezen.3.De correcte verwijdering van uw oude toestelhelpt negatieve gevolgen voor het milieu en demenselijke gezondheid voorkomen.Smaltimento delle apparecchiature obsoleteKassering av din gamla apparatUw oude toestel wegdoen1.Ce symbole, représentant une poubelle surroulettes barrée d'une croix, signifie que leproduit est couvert par la directive européenne2002/96/EC.2.Les éléments électriques et électroniquesdoivent être jetés séparément, dans les vide-ordures prévus à cet effet par votre municipalité. 3.Une élimination conforme aux instructions aideraà réduire les conséquences négatives et risqueséventuels pour l'environnement et la santéhumaine.4.Pour plus d'information concernant l'éliminationde votre ancien appareil, veuillez contacter votremairie, le service des ordures ménagères ouencore la magasin où vous avez acheté ceproduit.Élimination de votre ancien appareilun bidone della spazzatura barrato da una crocesignifica che il prodotto è coperto dalla direttivaeuropea 2002/96/EC.2.Tutti i prodotti elettrici ed elettronici dovrebberoessere smaltiti separatamente rispetto allaraccolta differenziata municipale, medianteimpianti di raccolta specifici designati dalgoverno o dalle autorità locali.3.Il corretto smaltimento delle apparecchiatureobsolete contribuisce a prevenire possibiliconseguenze negative sulla salute umana esull'ambiente.4.Per informazioni più dettagliate sullo smaltimentodelle apparecchiature obsolete, contattare ilcomune, il servizio di smaltimento rifiuti o ilnegozio in cui è stato acquistato il prodotto. EnglishFrenchItalianSwedishDutchWEEE (for Europe )
Regulatory Information cont. 091.Wenn dieses Symbol eines durchgestrichenenAbfalleimers auf einem Produkt angebracht ist,unterliegt dieses Produkt der europäischenRichtlinie 2002/96/EC.2.Alle Elektro- und Elektronik-Altgeräte müssengetrennt vom Hausmüll  über dafür staatlichvorgesehenen Stellen entsorgt werden.3.Mit der ordnungsgemäßen Entsorgung des altenGeräts vermeiden Sie Umweltschäden und eineGefährdung der persönlichen Gesundheit. 4.Weitere Informationen zur Entsorgung des altenGeräts erhalten Sie bei der Stadtverwaltung,beim Entsorgungsamt oder in dem Geschäft, woSie das Produkt erworben haben. 1.ŸÙ·Ó ¤Ó· ÚÔ˚fiÓ ‰È·ı¤ÙÂÈ ÙÔ ‰‡Ì‚ÔÏÔ ÂÓfi˜‰È·ÁÚ·Ì̤ÓÔ˘ οϷıÔ˘ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÙfiÙ ÙÔ ÚÔ˚fiÓηχÙÂÙ·È ·fi ÙËÓ E˘Úˆ·˚΋ O‰ËÁ›· 2002/96/EOK.2.H ·fiÚÚÈ„Ë fiÏˆÓ ÙˆÓ ËÏÂÎÙÚÈÎÒÓ Î·È ËÏÂÎÙÚÔÓÈÎÒÓÚÔ˚fiÓÙˆÓ Ú¤ÂÈ Ó· Á›ÓÂÙ·È ¯ˆÚÈÛÙ¿  ·fi Ù· ÁÂÓÈοÔÈÎȷο ·ÔÚÚ›ÌÌ·Ù· ̤ۈ ηıÔÚÈṲ̂ӈÓÂÁηٷÛÙ¿ÛÂˆÓ Û˘ÏÏÔÁ‹˜ ·ÔÚÚÈÌÌ¿ÙˆÓ, ÔÈ Ôԛ˜¤¯Ô˘Ó ‰ËÌÈÔ˘ÚÁËı› ›Ù ·fi ÙËÓ Î˘‚¤ÚÓËÛË ‹ ·fi ÙȘÙÔÈΤ˜ ·Ú¯¤˜.3.H ÛˆÛÙ‹ ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜ ı·‚ÔËı‹ÛÂÈ ÛÙËÓ ·ÔÙÚÔ‹ Èı·ÓÒÓ ·ÚÓËÙÈÎÒÓ Û˘ÓÂÈÒÓˆ˜ ÚÔ˜ ÙÔ ÂÚÈ‚¿ÏÏÔÓ Î·È ÙËÓ ˘Á›· ÙÔ˘ ·ÓıÚÒÔ˘.4.°È· ÈÔ ÏÂÙÔÌÂÚ›˜ ÏËÚÔÊÔڛ˜ Û¯ÂÙÈο Ì ÙËÓ·fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜, ÂÈÎÔÈÓˆÓ‹ÛÙ ÌÂÙÔ ·ÚÌfi‰›Ô ÙÔÈÎfi ÁÚ·Ê›Ô, ˘ËÚÂÛ›· ‰È¿ıÂÛ˘ ÔÈÎÈ·ÎÒÓ·ÔÚÚÈÌÌ¿ÙˆÓ ‹ ÙÔ Ì·Á·Í› ·fi ÙÔ ÔÔ›Ô ·ÁÔÚ¿Û·Ù ÙÔÚÔ˚fiÓ.1.Tämä merkki tuotteessa tarkoittaa, että tuotekuuluu sähkö- ja elektroniikkalaiteromustaannetun EU-direktiivin 2002/96/EYsoveltamisalaan.2.Kaikki elektroniset laitteet ovat ongelmajätettä, joten ne on toimitettava paikalliseenkeräyspisteeseen.3.Vanhan laitteen asianmukainen hävittäminen ehkäisee mahdollisia ympäristöön ja terveyteen kohdistuvia haittavaikutuksia.4.Lisätietoa vanhan laitteen hävittämisestä saat ottamalla yhteyden paikallisiin viranomaisiin,kierrätyskeskukseen tai myymälään, josta ostit laitteen.1.Når der er et tegn med et kryds over enskraldespand, betyder det, at produktet eromfattet af EU-direktiv 2002/96/EC.2.Alle elektriske og elektroniske produkter skalsmides ud et andet sted end gennem denkommunale affaldsordning ved hjælp af specielleindsamlingsfaciliteter, der er organiseret af staten1.Si en un producto aparece el símbolo de un contenedorde basura tachado, significa que éste se acoge a laDirectiva 2002/96/CE.2.Todos los aparatos eléctricos o electrónicos se debendesechar de forma distinta del servicio municipal derecogida de basura, a través de puntos de recogidadesignados por el gobierno o las autoridades locales.3.La correcta recogida y tratamiento de los dispositivosinservibles contribuye a evitar riesgos potenciales para elmedio ambiente y la salud pública.4.Para obtener más información sobre cómo deshacerse desus aparatos eléctricos y electrónicos viejos, póngase encontacto con su ayuntamiento, el servicio de recogida debasuras o el establecimiento donde adquirió el producto. Vanhojen laitteiden hävittäminenEntsorgung von AltgerätenSådan smider du dit gamle apparat ud∞fiÚÚÈ„Ë Ù˘ ·ÏÈ¿˜ Û·˜ Û˘Û΢‹˜Cómo deshacerse de aparatos eléctricos yelectrónicos viejoseller de lokale myndigheder.3.Korrekt bortskaffelse af dit gamle apparat er medtil at forhindre mulige skadevirkninger på miljøetog menneskelig sundhed. 4.Mere detaljerede oplysninger om bortskaffelse afdit gamle apparat kan fås ved at kontakte ditlokale kommunekontor, renovationsselskab ellerden butik, hvor du købte produktet. FinnishGermanDanishGreekSpanish4.Wilt u meer informatie over de verwijdering vanuw oude toestel? Neem dan contact op met uwgemeente, de afvalophaaldienst of de winkelwaar u het product hebt gekocht.
Regulatory Information cont. 10                        PortugueseSlovakCzechCroatianHungarianPolish
                  Regulatory Information cont. 11EstonianLatvianLithuanian

Navigation menu