LG Electronics USA TU50PY22 Plasma Display Panel User Manual 528Aen TU 50PY22 1
LG Electronics USA Plasma Display Panel 528Aen TU 50PY22 1
Contents
- 1. User Manual Part 1
- 2. User Manual Part 2
User Manual Part 1
PLASMA TV OWNER’S MANUAL 50PY2DR MODELS: 50PY2DR-UA 60PY2DR 60PY2DR-UA 50PX4DR 50PX4DR-UA TruSurround XT TM Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service. Model Number : Serial Number : LG Electronics U.S.A., Inc. Warning/Caution Warning/Caution WARNING/CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING/CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING/CAUTION: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. FCC NOTICE • A Class B digital device This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product. COMPLIANCE: The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-800-243-0000 http://www.lgusa.com WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 2 Plasma TV TV Guide On Screen Notices for U.S.A. Trademark Notice In the United States, TV GUIDE and other related marks are registered marks of Gemstar-TV Guide International, Inc. and/or one of its affiliates. In Canada, TV GUIDE is a registered mark of Transcontinental Inc., and is used under license by Gemstar-TV Guide International, Inc. Aux Etats Unis TV GUIDE et d’autres marques relatives sont des marques déposées de Gemstar-TV Guide International, Inc. et/ou d’une de ses sociétés affiliées. Au Canada TV GUIDE est une marque déposée de Transcontinental Inc., utilisée sous licence de Gemstar-TV Guide International, Inc. License Notice The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide International, Inc. and/or one of its affiliates. Le système TV Guide On Screen est fabriqués sous licence de Gemstar-TV Guide International, Inc. et/ou d’une de ses sociétés affiliées. Patent Notice The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. Le système TV Guide On Screen est protégés par un ou plusieurs brevets émis aux Etats Unis, comme le 6,498,895, 6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121. Use of the CableCARDTM TradeMark. “CableCARDTM is a trademark of Cable Television Laboratories, Inc.” Digital Cable Compatibility This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by direct connection to a cable system providing such programming. A security card provided by your cable operator is required to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable operator enhanced program (For example, electronic program guide provided by the cable operator), and data enhanced television service may require the use of a set top box. For more information contact your local cable operator. Owner’s Manual 3 Warning/Caution Safety Instructions IMPORTANT SAFETY INSTRUCTIONS Important safety instructions shall be provided with each apparatus. This information shall be given in a separate booklet or sheet, or be located before any operating instructions in an instruction for installation for use and supplied with the apparatus. This information shall be given in a language acceptable to the country where the apparatus is intended to be used. The important safety instructions shall be entitled “Important Safety Instructions”. The following safety instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety information may be included by adding statements after the end of the following safety instruction list. At the manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be placed immediately adjacent to that safety instruction : 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong, The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. PORTABLE CART WARNING 4 Plasma TV Safety Instructions 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has exposed to rain or moisture, does not operate normally, or has been dropped. 15. CAUTION concerning the Power Cord : Most appliances recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 16. Outdoor Use Marking : WARNING - To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose This Appliance To Rain Or Moisture. 17. Wet Location Marking : Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. Owner’s Manual 5 Contents Contents Warning/Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Digital Cable Compatibility . . . . . . . . . . . . . . . . . . . . . . . . .3 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4~5 Introduction Controls/Connection Options . . . . . . . . . . . . .8~11 Remote Control Key Functions . . . . . . . . . . 12~13 Installation Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Installation Instructions . . . . . . . . . . . . . . . . . .14~18 Joining the TV assembly to the wall to protect the set tumbling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Install the RING SPACER with the bolts on the set .. as shown . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Remove or Attache the Plate Cover . . . . . . . . . . .17 Swivel function . . . . . . . . . . . . . . . . . . . . . . . . .18 Arrangement wires . . . . . . . . . . . . . . . . . . . . . .18 External Equipment Connections . . . . . . . . . .19~25 Antenna or Cable Connection . . . . . . . . . . .19~20 VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .20 External A/V Source Setup . . . . . . . . . . . . . . . .21 DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 CableCARDTM Setup . . . . . . . . . . . . . . . . . . . . .22 HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . .22 PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . .23~24 Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . .25 Digital Audio Output . . . . . . . . . . . . . . . . . . . . .25 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26~28 TV Guide On Screen Setup . . . . . . . . . . . . . .29~35 Operation Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .36 HOME Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 TV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .38~56 On-screen Menus Language Selection . . . . . . .38 Setup Menu Options EZ Scan (Channel Search) . . . . . . . . . . . . . . . .39 Manual Scan . . . . . . . . . . . . . . . . . . . . . . . . . .39 Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .40 DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .40 Channel Label Setup . . . . . . . . . . . . . . . . . . . .41 Main Picture Source Selection . . . . . . . . . . . . .41 Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Video Menu Options EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Manual Picture Control (Custom Option) . . . . . .42 Color Temperature Control . . . . . . . . . . . . . . . .42 Video Reset . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Audio Menu Options Audio Language . . . . . . . . . . . . . . . . . . . . . . . .43 EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .43 Manual Sound Control (custom Option) . . . . . . .44 Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .44 TV Speakers On/Off Setup . . . . . . . . . . . . . . . .45 Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .45 BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 Time Menu Options Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .46 Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .46 On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .46 Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .47 Option Menu Features Advanced . . . . . . . . . . . . . Cinema 3:2 Mode Setup Low Power . . . . . . . . . . LG Logo . . . . . . . . . . . . Aspect Ratio Control . . . . . Caption . . . . . . . . . . . . . . . Caption / Text . . . . . . . . . . Caption Option . . . . . . . . ISM Method . . . . . . . . . . . Front Display . . . . . . . . . . Auto Demo . . . . . . . . . . . . Lock Menu Options Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .56 Recorded TV . . . . . . . . . . . . . . . . . . . . . . .57~61 Notes on Memory Card . . . . . . . . . . . . . . . .62~75 Photo List . . . . . . . . . . . . . . . . . . . . . . . . . .62~67 Music List . . . . . . . . . . . . . . . . . . . . . . . . . .68~70 Timeshift . . . . . . . . . . . . . . . . . . . . . . . . . . .71~72 Recording . . . . . . . . . . . . . . . . . . . . . . . . . .73~75 TV Guide On ScreenTM System . . . . . . . . . . .76~96 IEEE 1394 . . . . . . . . . . . . . . . . . . . . . . . . . .97~108 CableCARDTM Function Cable menu options . . . . . . . . . . . . . . . . . . . .109 Scrambled channel . . . . . . . . . . . . . . . . . . . . .109 Cable Channel List . . . . . . . . . . . . . . . . . . . . .110 Emergency Alert Message . . . . . . . . . . . . . . . .110 Remote Control PIP (Picture-in-Picture)/Twin Picture Watching PIP/POP/Twin Picture . . . . . . . . . . ..111 Selecting an Input Signal Source for PIP/Twin Picture .111 Swapping PIP/Twin Picture . . . . . . . . . . . . . . .111 TV Program Selection for PIP . . . . . . . . . . . . .111 Moving the PIP sub picture . . . . . . . . . . . . . . .112 Adjusting Main and Sub Picture Sizes for Twin Picture .112 POP (Picture-out-of-Picture: Channel Scan) . .112 APM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113 Bried Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114 EZ Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115 Screen Setup for PC mode . . . . . . . . . . . . . . . . .116 External Control Device Setup . . . . . . . . . . . . . .117~122 IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123~124 Programming the Remote Programming Codes . . . . . . . . . . . . . . . . . . . . .125 . . . . . . . . . . . . . . . . . . . . .126~127 Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . .128 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 Product Specifications . . . . . . . . . . . . . . . . . . . . . . . .130 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131~132 After reading this manual, keep it handy for future reference. 6 Plasma TV . . . . . . . . . . . . . . . .48 . . . . . . . . . . . . . . . .48 . . . . . . . . . . . . . . . .48 . . . . . . . . . . . . . . . .49 . . . . . . . . . . . . . . . .50 . . . . . . . . . . . . . . . .51 . . . . . . . . . . . . . . . .51 . . . . . . . . . . . . . . . .52 . . . . . . . . . . . . . . . .53 . . . . . . . . . . . . . . . .53 . . . . . . . . . . . . . . . .54 Introduction Introduction What is a Plasma Display Panel (PDP)? A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps. How does it work? PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors. You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of these mean that you get perfect images that are easily viewable in a display that is less than 5 inches thick. 160° - Wide angle range of vision Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen. Wide Screen The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater. Multimedia Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously. Versatile The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit. The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen The PDP (Plasma Display Panel), which is the display device of this product, is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product. Cooling Fan Noise In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned. Owner’s Manual 7 Introduction Controls This is a front panel of 50PY2DR, 60PY2DR series TVs. - This is a simplified representation of front panel. Here shown may be somewhat different from your TV. - This manual explains the features available on the 50PY2DR, 60PY2DR series TVs. CHANNEL Buttons Front Panel Controls VOLUME Buttons MENU Button TV/VIDEO Button TV GUIDE Button POWER Button Memory Card Slots 1,2 Remote Control Sensor INDEX Switches LED Display on or off. Programme Display green. And after orange stop blinking, you can directly turn on the TV. But in case of green, screen is displayed in 3~4 seconds later. RGB-PC(or RGB-DTV) mode On recording IEEE1394 mode On playing HDMI1/DVI or HDMI2 mode On operating the TimeShift Component1 or 2 mode On setting the reserve record Antenna or Cable mode On operating the Video or Front Video mode 8 Plasma TV Power Standby Indicator When the TV is turned on, blinks orange in standby mode, blinks mode Introduction Connection Options This is a back panel of 50PY2DR, 60PY2DR series TVs. Back Connection Panel S-VIDEO Input A connection available to provide better picture quality than the video input. S-VIDEO FRONT A/V INPUT AUDIO INPUT VIDEO INPUT RS-232C INPUT (CONTROL/SERVICE) DVD /DTV INPUT OUTPUT I 1 HDMI 2 COMPONENT2 INPUT E3 E9 DIGITAL AUDIO (OPTICAL) HDMI /DVI R AUDIO L / MONO VIDEO VIDEO Input Connects the video signal from a video device. VIDEO COMPONENT MONITOR OUTPUT COMPONENT A/V INPUT1 AUDIO (MONO) R C M N O T ANTENNA CABLE RGB INPUT AC INPUT AUDIO INPUT DVI INPUT E4 AUDIO Input Use to connect to hear stereo sound from an external device. RS-232C INPUT (CONTROL/SERVICE) PORT Connect to the RS232C port on a PC. Cable G-LINK Connect an IR controller to this jack. CableCARD™ Used for CableCARD™ received Cable Service Provider. IEEE1394 Connect DVHS or MicroMV to IEEE1394 Connector. DVD/DTV Input (Component 1-2) Connect a component video/audio device to these jacks. RGB/AUDIO INPUT Connect the monitor output connector from a PC to the appropriate input port. Remote Control Port Connect your wired remote control here. S-Video Input Connect SVideo out from an S-VIDEO device. Antenna Input Connect antenna signals to the TV. RS-232C INPUT (CONTROL/SERVICE) VIDEO OUTPUT AUDIO HDMI 2 COMPONENT2 INPUT IEEE-1394 DVI INPUT HDMI1/DVI(VIDE O), HDMI 2 Connect a HDMI signal to HDMI1/DVI or HDMI2. Or DVI(VIDEO) signal to HDMI1/DVI port with DVI to HDMI cable. AUDIO AC INPUT COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT 1 DIGITAL AUDIO (OPTICAL) RGB INPUT HDMI /DVI VIDEO Digital Audio (DVI: Digital Visual Interface/Compon ent2) Input/ Digital Audio Output Connect digital audio from various types of equipment. Note: In standby mode, these ports will not work. AUDIO INPUT DVD /DTV INPUT REMOTE CONTROL CABLE ANTENNA (MONO) Audio/Video Input Connect audio/video output from an external device to these jacks. S-VIDEO Monitor Output Connect a second TV or Monitor. CABLE Input Connect cable signals to the TV, either directly or through your cable box. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. Note: - After removing the cover, you can insert the CableCARD™ or connect to the G-LINK jack. Owner’s Manual 9 Introduction Controls This is a front panel of 50PX4DR series TVs. - This is a simplified representation of front panel. Here shown may be somewhat different from your TV. Front Panel Controls INDEX Switches LED Display on or off. TV GUIDE TV GUIDE CHANNEL (E, D) Buttons VOLUME (F,G) Buttons MENU Button TV/VIDEO Button TV GUIDE Button Remote Control Sensor POWER Button 10 Plasma TV Power Indicator Illuminates orange in standby mode, Illuminates green when the TV is turned on. (If illuminated in red and the power is off contact your service center.) Introduction Connection Options This is a back panel of 50PX4DR series TVs. Back Connection Panel S-VIDEO Input A connection available to provide better picture quality than the video input. FRONT A/V INPUT VIDEO S-VIDEO R AUDIO L / MONO VIDEO Input Connects the video signal from a video device. AUDIO Input Use to connect to hear stereo sound from an external device. Memory Card Slots RGB/AUDIO INPUT Connect the monitor output IEEE1394 connector from a PC to the Connect DVHS or appropriate input port. MicroMV to IEEE1394 DVD/DTV Input Connector. (Component 1-2) Connect a DVHS, a RS-232C INPUT (CONMicroMV Camcorder, or TROL/SERVICE) PORT a Set-Top Box to one of G-LINKTM Connect to the RS-232C IEEE1394 connectors. Connect an IR port on a PC. controller to this jack. Remote Control Port Connect your wired remote control here. S-Video Input Connect SVideo out from an S-VIDEO device to the SVIDEO input. Antenna Inputs Connect antenna signals to the TV. RS-232C INPUT (CONTROL/SERVICE) VIDEO OUTPUT AUDIO HDMI 2 COMPONENT2 INPUT IEEE-1394 AUDIO INPUT DVI INPUT CableCARD™ Used for CableCARD™ received from Cable Service Provider. AUDIO AC INPUT MONITOR OUTPUT DIGITAL AUDIO (OPTICAL) RGB INPUT HDMI1/DVI Cable VIDEO COMPONENT INPUT 2 Digital Audio (DVI: Digital Visual Interface/Component2) Input/ Digital Audio Output Connect digital audio from HDMI1/DVI, HDMI 2 various types of equipment. Connect a HDMI sig- Note: In standby mode, nal to HDMI1/DVI or these ports will not work. HDMI2. Or connect a DVI(Video) signal to HDMI1/DVI. DVD /DTV INPUT REMOTE CONTROL CABLE ANTENNA (MONO) COMPONENT INPUT 1 Audio/Video Input Connect audio/video output from an external device to these jacks. A/V INPUT S-VIDEO Monitor Output Connect a second TV or Monitor. CABLE Inputs Connect cable signals to the TV, either directly or through your cable box. Power Cord Socket This TV operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the TV on DC power. Owner’s Manual 11 Introduction Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the TV. POWER Turns your TV or any other programmed equipment on or off, depending on mode. TV INPUT TV/VIDEO MODE X STUDIO Bring up the HOME menu to the screen. THUMBSTICK (Up/Down/Left/Right/ENTER) Allows you to navigate the on-screen menus and adjust the system settings to your preference. DAY DAY - REC LIST Appear the thumbnail recorded list. DAY+/DAYMoves forward or backward in 24 hour increments in the Listings Grid. VOLUME UP/DOWN Increases/decreases the sound level. NUMBER buttons RATIO Changes the aspect ratio. SAP Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language in DTV mode. CC Select a closed caption: Off, CC1~4, Text1~4. M/C EJECT When removing the Memory Card, this button is used. LIGHT Illuminates the remote control buttons. 12 Plasma TV VCR/DVD BUTTONS • Control some video cassette recorders or DVD players. ("RECORD" button is not available for DVD players.) < Only TV mode > •In Photo mode of Xstudio, the view state changes to the slide show state with “PLAY” button and the slide show state changes to the view state with “PAUSE” button. • In Music mode of Xstudio, controls the music with “PAUSE”, “STOP”, ”PLAY”, ”(Left/Right) SKIP” buttons. Note that FF and REW do not work in the mode. •Control the DVHS or Camcorder of IEEE 1394 mode. FLASHBK APM CC AUTO DEMO M/C EJECT CHANNEL UP/DOWN Selects available channels found with EZ scan. PAGE UP/PAGE DOWN Moves from one full set of screen information to the next one. EZ SOUND Selects the sound appropriate for the program's character. APM Concurrently, compare with the Daylight, Normal, Night Time and Custom on the screen. (Refer to p.112) Introduction TV INPUT When you watch the TV, Antenna and Cable is toggled. In Video, Front Video, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI, HDMI2 and IEEE1394 input sources, screen return to the last TV channel. TV INPUT MODE Selects the remote operating mode: TV, DVD, VCR, AUDIO, CABLE or STB. Select other operating modes, for the remote to operate external devices. TV/VIDEO MODE DAY DAY - TV/VIDEO Selects: Video 1-2, Component 1-2, RGB-DTV (or RGB-PC), HDMI1/DVI and HDMI2 input sources. (Only when the jack connects , Video 1-2, Component 1-2 input sources are linked automatically) TV GUIDE Brings up the TV Guide On Screen system to the screen. MENU Brings up the main menu to the screen. Enters or exits a Panel Menu in the TV Guide On Screen system. INFO When you watch the TV, information displays on top of the screen. Not available in Component 1-2, RGB, HDMI1/DVI and HDMI2 mode.(Refer to p.113) EXIT Clears all on-screen displays and returns to TV viewing from any menu. Mark Selects the wanted functions. MUTE Switches the sound on or off.(Refer to p.114) FAV Scroll the Favorite channels. TIMER Lets you select the amount of time before your TV turns itself off automatically. FLASHBK FLASHBK Tunes to the last channel viewed. ADJUST Adjusts screen position, size, and phase in PC mode. APM CC AUTO DEMO M/C EJECT EZ PIC Adjusts the factory preset picture depending on the viewing environment. AUTO DEMO Displays the slide show to explain the main features of this TV. PIP Switches between PIP, POP (Picture-outof-Picture) and Twin picture modes. Switches the video window locking or unlocking in the Listings Grid. PIPCH-/PIPCH+ Changes to next higher/lower PIP channel. PIP INPUT Selects the input source for the sub picture. SWAP Exchanges the main/sub images in PIP/Twin picture mode. Installing Batteries • Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -). • Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones. Replace cover. Owner’s Manual 13 Installation Installation Accessories Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product. TV INP DE MO DAY DAY SH BK FLA 1.5V 1.5V Owner’s Manual Batteries AP O DEM AUT CC Remote Control Power Cord G-LINK Cable D-sub 15 pin Cable 75Ω Round Cable 6-RING SPACER (Only 60PY2DR series ) 6-Wall mounting bracket bolts (Only 60PY2DR series ) 2-Wall brackets(50”) 2-Wall brackets(60”) 2-TV brackets(60”) 2-eye-bolts(50”) 2-TV bracket bolts(60”) Installation Instructions Joining the TV assembly to the wall to protect the set tumbling - Secure the TV assembly by joining it to a wall by using the TV/Wall brackets. - Here shown may be somewhat different from your TV. 50PY2DR • After the set must be mounted on the desk top, Insert the 2 eye-bolts and tighten securely in the upper holes as shown. Install wall the brackets on the wall with 2 bolts*, (not supplied with the product), as shown. Match the height of the eye-bolts and the wall brackets. Check to be sure the eye-bolts or the brackets are tightened securely. 14 Plasma TV Installation 60PY2DR • After the set must be mounted on the desk top, install the 2 ring spacer on the TV. And then install the TV brackets on the ring spacer as shown. Insert the 2 bolts and tighten securely, in the upper holes on the brackets. Install the wall brackets on the wall with 2 bolts*, (not supplied with the product). Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely. 50PX4DR • After the set must be mounted on the desk top, Insert the 2 eye-bolts and tighten securely in the upper holes as shown. Install wall the brackets on the wall with 2 bolts*, (not supplied with the product), as shown. Match the height of the eye-bolts and the wall brackets. Check to be sure the eye-bolts or the brackets are tightened securely. • Secure the TV assembly to the wall with strong strings or wire cables, (not supplied with the product), as shown. Install the RING SPACER SPACER with the bolts on the set as shown. (Only 60PY2DR series ) 2. When you connect the wall mounting bracket to the set, connect to it by using the bolts, (supplied with the product), as shown. 1. Put the RING SPACER in the holes of the bolts before connecting to the wall mounting bracket. Owner’s Manual 15 Installation Installation Instructions • The TV can be installed in various ways such as on a wall, or on a desktop etc. • The TV is designed to be mounted horizontally. - This manual explains the features available on the 50PY2DR, 60PY2DR series TVs. - Here shown may be somewhat different from your TV. GROUNDING Power Supply Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. Wall Mount: Horizontal installation For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation. Short-circuit Breaker Desktop Pedestal Installation For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation. 2 inches 4 inches 4 inches 4 inches 4 inches 4 inches 16 Plasma TV 4 inches 2 inches 4 inches 2.36 inches Installation Remove or Attache the Plate Cover (Only 50/60PY2DR series ) - This function explains the features available on the 50PY2DR, 60PY2DR series TVs. • When moving or connecting the power cord, be used the these methods. • And after removing the plate cover, you must install the wall brackets on the wall. AUDIO INPUT VIDEO INPUT RS-232C INPUT (CONTROL/SERVICE) DVD /DTV INPUT OUTPUT I 1 HDMI 2 E3 E4 VIDEO COMPONENT MONITOR OUTPUT COMPONENT A/V INPUT1 AUDIO M N O T DIGITAL AUDIO (OPTICAL) CABLE INPUT HDMI /DVI R C (MONO) COMPONENT2 E9 RGB INPUT ANTENNA AC INPUT AUDIO INPUT DVI INPUT 1. With hands, push the lower left/right of plate cover and then pull out to the front. 2. Connect the power cord on the TV’s back. 3. In attaching the plate cover, firstly you set projection of the GUIDE to BUSHING RUBBER of the upper left/right. Push and put the plate cover with hands. Owner’s Manual 17 Installation Installation Instructions Swivel function - This function explains the features available on the 50PY2DR, 60PY2DR series TVs. • After installing the TV, you can adjust the the TV set manually to the left or right direction by 20 degrees to suit your viewing position. Note: Before adjusting the angle, you must loosen (to the left) the shaft bolt on the middle of stand’s back. And when stand be level with TV, you must close (to the right) the shaft bolt to set the hole.(As shown below) 50/60PY2DR 20° 50PX4DR 20° Arrangement wires (Only 50/60PY2DR series ) - This function explains the features available on the 50PY2DR, 60PY2DR series TVs. • Run the accessory device wires inside the JACK MANAGEMENT pole as shown. AUDIO INPUT VIDEO INPUT RS-232C INPUT (CONTROL/SERVICE) DVD /DTV INPUT OUTPUT I 1 HDMI 2 E3 E4 VIDEO MONITOR OUTPUT A/V INPUT1 AUDIO M N O T CABLE RGB INPUT DVI R C (MONO) DIGITAL AUDIO (OPTICAL) INPUT HDMI /DVI INPUT 18 Plasma TV COMPONENT COMPONENT COMPONENT2 E9 AUDIO INPUT ANTENNA AC INPUT Installation External Equipment Connections Antenna or Cable Connection 1. Analog and Digital TV signals provided on antenna - Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections - For optimum picture quality, adjust antenna direction if needed. Multi-family Dwellings/Apartments (Connect to wall antenna socket) AC INPUT Wall Antenna Socket CABLE ANTENNA Bronze Wire RF Coaxial Wire (75 ohm) VHF Antenna Turn clockwise to tighten. UHF Antenna Bronze Wire Outdoor Antenna Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna) Be careful not to bend the bronze wire when connecting the antenna. 2. Analog and Digital TV signals provided on cable Cable TV Wall Jack Turn clockwise to tighten. RF Coaxial Wire (75 ohm) AC INPUT CABLE ANTENNA Bronze Wire Owner’s Manual 19 Installation 3. Analog and Digital TV signals provided on cable and antenna Antenna Bronze Wire RF Coaxial Wire (75 ohm) AC INPUT Cable TV Wall Jack Turn clockwise to tighten. RF Coaxial Wire (75 ohm) ANTENNA CABLE Bronze Wire • In a poor signal area to improve picture quality, purchase and install a signal amplifier. ANTENNA • If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections. • If the antenna is not installed properly, contact your dealer for assistance. Signal Amplifier Note: The TV will let you know when the analog, cable, and digital channel scans are complete. VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV - Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen. Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. AUDIO INPUT VIDEO INPUT S-232C INPUT NTROL/SERVICE) Connection Option 2 1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input. 2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.) 3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT , select Video input source) Do not connect to both Video and S-Video at the same time. 20 Plasma TV DVD /DTV INPUT VIDEO COMPONENT MONITOR OUTPUT COMPONENT A/V INPUT1 L AUDIO R (MONO) R C E O M N O T T R E O DIGITAL AUDIO (OPTICAL) CABLE RGB INPUT ANTENNA AC INPUT AUDIO INPUT ANT OUT VCR Rear ANT IN S-VIDEO OUT OUTPUT SWITCH 3 4 IN (R) AUDIO (L) VIDEO Installation External A/V Source Setup How to connect RS-232C INPUT (CONTROL/SERVICE) Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). VIDEO OUTPUT AUDIO HDMI 2 VIDEO COMPONENT INPUT 2 COMPONENT2 INPUT AUDIO AC INPUT MONITOR OUTPUT DIGITAL AUDIO (OPTICAL) DMI /DVI DVD /DTV INPUT AUDIO INPUT RGB INPUT CABLE ANTENNA (MONO) DVI INPUT COMPONENT INPUT 1 A/V INPUT How to use 1. Select the input source with using the TV/VIDEO button on the remote control. Note that this TV finds the connected input sources automatically for Video 1-2 and Component 12. It is presumed that RGB, HDMI1/DVI and HDMI2 sources are connected. 2. Operate the corresponding external equipment. For connection instructions for operating the TV Guide On Screen system, see page 29. Camcorder R AUDIO L VIDEO Video Game Set DVD Setup RS-232C INPUT (CONTROL/SERVICE) VIDEO OUTPUT AUDIO HDMI 2 Cable VIDEO COMPONENT INPUT 2 COMPONENT2 INPUT IEEE-1394 AUDIO AC INPUT MONITOR OUTPUT DIGITAL AUDIO (OPTICAL) HDMI1 /DVI RGB INPUT DVD /DTV INPUT AUDIO INPUT REMOTE CONTROL CABLE ANTENNA (MONO) DVI INPUT COMPONENT INPUT 1 A/V INPUT or S-VIDEO DVD or DIGITAL AUDIO OPTICAL (R) AUDIO (L) S-VIDEO (R) AUDIO (L) How to connect 1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. 2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure. Note: If your DVD player does not have component video output, use S-Video. How to use 1. Turn on the DVD player, insert a DVD. 2. Use the TV/VIDEO button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video or Front Video external input source.) 3. Refer to the DVD player's manual for operating instructions. • Component Input ports To get better picture quality, connect a DVD player to the component input ports as shown below. Component ports on the TV PB Video output ports on DVD player Pr Pb B-Y R-Y Cb Cr PB PR PR Notes: • Digital Audio will not work for Component 1 input source. • Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time. Owner’s Manual 21 Installation TM CableCARDTM Setup How to use Insert the CableCARDTM received from the cable service provider to the CableCARDTM slot of TV back panel. If the pairing information about this TV and the CableCARD is automatically displayed on the screen, contact with the cable service provider by phone. RS-232C INPUT (CONTROL/SERVICE) OUTPUT HDMI 2 Cable COMPONENT2 INPUT IEEE-1394 DIGITAL AUDIO (OPTICAL) HDMI1 /DVI Note : • CableCARDTM have the types of Motorola, Scientific Atlanta, SCM etc.. These 3 types of CableCARDTM can be used for this PLASMA TV. RGB I DVI INPUT Caution: When removing the CableCARDTM, do not drop it as this may cause damage to the CableCARDTM. HDSTB Setup - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. - This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). RS-232C INPUT (CONTROL/SERVICE) VIDEO OUTPUT AUDIO HDMI 2 COMPONENT2 INPUT IEEE-1394 AUDIO AC INPUT MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT DIGITAL AUDIO (OPTICAL) RGB INPUT HDMI1 /DVI VIDEO COMPONENT INPUT 2 AUDIO INPUT DVI INPUT DVD /DTV INPUT (R) AUDIO (L) ANTENNA S-VIDEO or or RGB-DTV OUTPUT CABLE REMOTE CONTROL (MONO) (R) AUDIO (L) DIGITAL AUDIO OPTICAL DVI-DTV OUTPUT HDMI-DTV OUTPUT DIGITAL AUDIO OPTICAL (R) AUDIO (L) Digital Set-top Box How to connect Use the TV’s COMPONENT (Y, PB, PR) INPUT, RGB, HDMI1/DVI or HDMI2 jack for video connections, depending on your set-top box connector. Then, make the corresponding audio connections. How to use 1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.) 2. Use TV/VIDEO on the remote control to select Component 1, Component 2, RGB-DTV, HDMI1/DVI or HDMI2 source. 22 Plasma TV Signal 480i 480p 720p 1080i Component 1/2 RGB-DTV,HDMI1/DVI,HDMI2 Yes No Yes Yes Yes Yes Yes Yes Installation PC Setup - This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. - The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic card accordingly.How to connect 1. Connect the PC to HDMI1/DVI port of this TV with an HDMI-to-DVI cable(not supplied with this product). If you do not need to connect audio, HDMI2 port is also available for the DVI video connection. 2. If the PC(or the sound card of the PC) has a fiber optic digital audio output connector, connect the PC's audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT. 3. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz. 2. Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.62) TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. How to connect 1. Connect the PC to RGB INPUT port of this TV with a RGB cable. 2. If the PC(or the sound card of the PC) has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use 1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60 Hz. 2. Select RGB-PC input source in main input option of SETUP menu.(Refer to P.41) Once you select RGB-PC in main input option of SETUP menu, TV/VIDEO button is also available for this purpose. 3. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the VIDEO menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card. Owner’s Manual 23 Installation Monitor Display Specifications (RGB-PC ) Resolution 720x400 640x480 Vertical Horizontal Frequency(KHz) Frequency(Hz) 31.469 70.08 37.927 85.03 31.469 59.94 37.861 37.500 43.269 Resolution Horizontal Vertical Frequency(KHz) Frequency(Hz) 35.156 56.25 37.879 60.31 48.077 72.18 72.80 46.875 75.00 75.00 53.674 85.06 85.00 48.363 60.00 56.476 70.06 60.023 75.02 800x600 1024x768 Monitor Display Specifications (RGB-DTV ) Resolution 720x480 1280x720 1920x1080 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.47 59.94 31.50 60 45.00 60.00 44.96 59.94 33.75 60.00 33.72 59.94 Monitor Display Specifications (HDMI-PC) Resolution 640x480 800x600 Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.469 59.94 37.861 72.80 37.500 75.00 43.269 85.00 35.156 56.25 37.879 60.31 48.077 72.18 46.875 75.00 53.674 85.06 Monitor Display Specifications (HDMI-DTV) Resolution 720x480 1280x720 1920x1080 24 Plasma TV Horizontal Vertical Frequency(KHz) Frequency(Hz) 31.500 60 31.469 59.94 45.00 60.00 44.96 59.94 33.75 60.00 33.72 59.94 Resolution 1024x768 Horizontal Vertical Frequency(KHz) Frequency(Hz) 48.363 60.00 56.476 70.06 60.023 75.02 Installation Monitor Out Setup VIDEO AUDIO RGB INPUT AUDIO INPUT VIDEO AUDIO AC INPUT COMPONENT INPUT 2 MONITOR OUTPUT COMPONENT INPUT 1 A/V INPUT DVD /DTV INPUT REMOTE CONTROL CABLE The TV has a special signal output capability which allows you to hook up a second TV or monitor. ANTENNA (MONO) S-VIDEO Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings. Note • Component, RGB-PC/RGB-DTV, HDMI1/DVI and HDMI2 , DTV input sources cannot be used for Monitor out. S-VIDEO IN VIDEO (L) AUDIO (R) Digital Audio Output Send the TV’s audio to external audio equipment via the Digital Audio Output (Optical) port. RS-232C INPUT (CONTROL/SERVICE) OUTPUT HDMI 2 How to connect 1. Connect one end of an optical cable to the TV Digital Audio (Optical) Output port. 2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment. 3. Set the “ TV Speaker option - Off” in the AUDIO menu. Refer to page 45. See the external audio equipment instruction manual for operation. Cable COMPONENT2 INPUT IEEE-1394 HDMI1 /DVI DIGITAL AUDIO (OPTICAL) RGB INPUT AUDIO INPUT DVD /DTV INPUT DVI INPUT Caution: Do not look into the optical output port. Looking at the laser beam may damage your vision. Owner’s Manual 25 Installation HDMI - HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC." - This TV can receive the High-Definition Multimedia Interface(HDMI) or the Digital Visual Interface(DVI). - This TV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for 720x480p, 1280x720p, and 1920x1080i resolution. - When you connect this TV with a source device(DVD player, Set Top Box or PC) supporting Auto HDMI/DVI function, the output resolution of the source device will be automatically set to 1280x720p. - If the source device does not support Auto HDMI1/DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the DVD Player or Set Top Box's output resolution to 1280x720p, and the PC graphics card's output resolution to 1024x768, 60Hz. - If the source device has an HDMI output, no other audio connection is necessary because HDMI-to-HDMI connection includes both video and audio. - If the source device has a DVI output and no HDMI output, a separated audio connection is necessary. How To Connect 1. Connect the source device to HDMI1/DVI or HDMI2 port of this TV with an HDMI cable(not supplied with this product). 2. No separated audio connection is necessary. How To Use - If the source device supports Auto HDMI function, the output resolution of the source device will be automatically set to 1280x720p. - If the source device does not support Auto HDMI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. - Select HDMI1/DVI or HDMI2 input source in main input option of SETUP menu.(Refer to P.41) VIDEO button is also available for this purpose. How To Connect 1. Connect the source device to HDMI1/DVI port of this TV with a HDMI-to-DVI cable(not supplied with this product). Do not use HDMI2 port for DVI connection if you want to connect audio. 2. A separated audio connection is necessary. 3. If the source device has a fiber optic digital audio output, connect the audio output to DIGITAL AUDIO(OPTICAL) port for DVI INPUT. 4. If the source device has an analog audio output connector, connect the PC's audio output to AUDIO INPUT port located on the right side of RGB INPUT port. How To Use - If the source device supports Auto DVI function, the output resolution of the source device will be automatically set to 1280x720p. - If the source device does not support Auto DVI, you need to set the output resolution appropriately. To get the best picture quality, adjust the output resolution of the source device to 1280x720p. - Select HDMI1/DVI input source in main input option of SETUP menu.(Refer to P.41) VIDEO button is also available for this purpose. 26 Plasma TV Installation Reference Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable (not supplied with the product) Fiber Optic Digital Audio Cable (not supplied with the product) Analog Audio Cable(RCA type) (not supplied with the product) Analog Audio Cable(Stereo to RCA type) (not supplied with the product) Owner’s Manual 27 Installation HDMI How to use 1. Connect the HDMI1/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET. 2. Turn on the display by pressing the POWER button on the TV SET and HDMI1/DVI Source Devices remote control. 3. Select HDM1/DVI Input source in Main Input option of SETUP menu.(Refer to P.41) 4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI1/DVI Source Devices. If noise is present, change the HDMI1/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card. Notes: - Depending on the graphics card, DOS mode may not work if you use a HDMI1 to DVI Cable. - Avoid keeping a fixed image on the TV SET screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible. - When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen. As shown the lower picture, press the ADJUST button to adjust the screen Position of TV SET and contact an PC graphics card service center. - When Source Devices connected HDMI1/DVI Input output TV SET Resolution(480p, 720p, 1080i), TV SET Display fit EIA/CEA861-B Specification to Screen. If not, refer to the Manual of HDMI1/DVI Source Devices or contact your service center. - In case HDMI1/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI1/DVI Input. And In case of, Video Resolution not supported TV SET output in HDMI1/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI1/DVI Source Devices or contact your service center. In This Mode, the Supported TV SET Resolution Specification 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format) 720 x 480 P @ 59.94Hz / 60Hz, 16:9 720 x 480 P @ 59.94Hz / 60Hz, 4:3 In This Mode, the Supported PC Resolution Specification 640 x 480 @ 59.94Hz 640 x 480 @ 72.80Hz 640 x 480 @ 75Hz 640 x 480 @ 85Hz 800 x 600 @ 56.25Hz 800 x 600 @ 60.31Hz 800 x 600 @ 72.18Hz 800 x 600 @ 75Hz 800 x 600 @ 85.06Hz 1024 x 768 @ 60Hz(preferred format) 1024 x 768 @ 70.06Hz 1024 x 768 @ 75.02Hz 28 Plasma TV Installation TV Guide On Screen Setup - The TV Guide On Screen system uses Setup information to provide you with show listings and lineups in your area—which are updated several times a day. - Once you set up the TV according to manufacturer’s instructions, you are ready to set up the TV Guide On Screen system. - To download program listings the TV Guide On Screen system needs to be able to change channels on your cable box when the TV is not in use. Please connect the supplied G-LINK cable to the G-LINK jack of the TV. After you connect the G-LINK cable you will be able to control your cable box using the TV’s remote. Note:The TV Guide On Screen system interactive program guide provides listings for cable-ready, cable box, and digital cable services as well as over-the-air broadcast. It does not provide listings for satellite services. How to connect Cable Box Cable Service with a Cable Box VIDEO AUDIO COMPONENT INPUT 2 VIDEO AUDIO AC INPUT MONITOR OUTPUT Cable DVD /DTV INPUT REMOTE CONTROL CABLE ANTENNA (MONO) COMPONENT INPUT 1 A/V INPUT 1 S-VIDEO or (R) AUDIO (L) OUTPUT SWITCH 3 4 TV SET Cable IN Cable Box Front VIDEO TV VCR Cable Box Rear Owner’s Manual 29 Installation Note: • The G-LINKTM cable is necessary for the TV Guide On Screen system to work with your Cable Box and VCR. See Page 29 for G-LINKTM connection instructions. TV Guide On Screen Setup 1.Welcome Screen The TV Guide On Screen system's Welcome Screen appears: -- by pressing the TV Guide key -- when you power On your TV if you previously skipped "Set up TV Guide On Screen now" on the Reminder Screen. The Welcome Screen highlights features of the TV Guide On Screen system. Press ENTER to begin Setup. 2.Reminder Screen The TV Guide On Screen system's Reminder Screen appears: -- after initial TV set up -- if you power Off the TV and then power it back On To make a selection, use the D / E button to highlight to an option, and press ENTER. • "Set up TV Guide On Screen now," displays the Welcome Screen. Press ENTER to begin Setup. • "Remind me to set up later" returns you to watching TV. • "Don't remind me again" returns you to watching TV and stops the reminder screen from appearing upon power On. How to use 1. Screen 1: Country • This screen asks you the location of your TV. • Use the D / E button to highlight a country. • Press ENTER to display Screen 2. 30 Plasma TV Installation 2. Screen 2: Enter Zip or Postal Code Option 1 • If you selected USA in Screen 1, you see the ZIP Code screen. • You input numbers by either pressing the number keys on the remote or using the D / E button to display a number, and then the F / G button to move to another field. • Press ENTER to display Screen 3. Option 2 • If you selected Canada in Screen 1, you see the Postal Code screen. • You input characters by using the D / E button, and then the F / G button to move to another field. • Press ENTER to display Screen 3. 3. Screen 3: Do you have Cable Service connected? • If you select Yes, you see Screen 4. • If you select No, you see Screen 12. 4. Screen 4: Do you have a Cable Box? • If you select Yes, you see Screen 5. • If you select No, you see Screen 12. Owner’s Manual 31 Installation 5. Screen 5: Which TV input is the cable box plugged into? • If you select Cable, you see Screen 6. • If you make any other choice, you see Screen 7 . 6. Screen 6: Cable Box Tuning Channel • Select the channel used for the cable box. • Press ENTER to display Screen 7. 7. Screen 7: Cable Box Configuration Diagram • The diagram shows the correct way to install the G-LINK Cable from the back of the device to the cable box. Make sure the G-LINKTM Cable is properly installed. • Press ENTER to display Screen 8. 32 Plasma TV Installation 8. Screen 8: Cable Box Brand Name • Use the D / E button to select a cable box brand. • Press ENTER to display Screen 9. 9. Screen 9: Cable Box Preparation • Follow the on-screen instructions, and press ENTER to display Screen 10. 10. Screen 10: Cable Box Code Testing • When testing is done, Screen 11 displays automatically. 11. Screen 11: Cable Box Tuned to Channel 9? • If you select Yes, you see Screen 12. • If you select No, a different code is tested in Screen 10. Note: • Many Cable Boxes require testing more than one code. • If you select Test this code again, the same code is tested again in Screen 10. Owner’s Manual 33 Installation 12. Screen 12: Do you have an antenna connected? •If you select Yes, you see Screen 13. Note: •If you selected No in Screen 3 then you must select Yes in this screen to receive a channel lineup and listings. •If you select No, you see Screen 13. 13. Screen 13: Are your basic settings correct? •If you select Yes, you see Screen 14. •If you select No, you see Screen 1. 14. Screen 14: Congratulations •Press ENTER to display Screen 15. 34 Plasma TV Installation 15. Screen 15: Helpful Information •This screen tells you valuable information on using your Guide. •Press ENTER to watch TV. Notes: • The TV Guide On Screen system receives program listings data through your cable or over-the-air video signal. In order to receive regular program listings, please remember to do the following: 1. Turn OFF your TV when it is not in use. (Do not unplug the power cord.) 2. If you have a Cable box connected, leave it ON. 3. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, please follow the on-screen instructions. Owner’s Manual 35 Operation Operation Turning the TV On 1. First, connect power cord correctly. At this moment, the TV switches to standby mode. In standby mode to turn TV on, press the power, TV/VIDEO, CH (D / E) button on the TV or press the POWER, TV/VIDEO, TV INPUT, CH (+, -), Number (0 ~ 9) button on the TV . 2. Select the viewing source by using TV/VIDEO, TV INPUT button on the remote control. This TV is programmed to remember which mode it was last set to, even if you turn the TV off. 3. When finished using the TV, press the POWER button on the remote control. The TV reverts to standby mode. Notes: • If you intend to be away on vacation, disconnect the power plug from the wall power outlet. • After turning on the TV, it will take up to a week for the TV Guide On Screen system to receive full listings data. • When the TV is turned on, blinks orange in standby mode, blinks green. And after orange stop blinking, you can directly turn on the TV. But in case of green, screen is displayed in 3~4 seconds later. • If power isn’t turn on in red, contact your service center. • When the power turns on, the screen of TV Guide is automatically showed. In case the prior condition turns on putting again after the power code puts out in conditon turning on power, the screen of TV Guide is showed a little bit late. 36 Plasma TV Operation HOME Menu - This menu is a contents guide. In HOME Menu, you enter the recorded list of DVR, photo list and music list of DVR or Memory Card, TV Guide,Schedule of the TV Guide, IEEE1394 or TV Menu. Recorded TV TV Menu Photo List Music List IEEE 1394 TV Guide Schedule Owner’s Manual 37 Operation TV Setup On-screen Menus Language Selection - The menus can be shown on the screen in the selected language. First select your language. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the button and then use button to select Language. 3. Press the G button and then use D / E button to select your desired language. From this point on, the on-screen menus will be shown in the selected language. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 38 Plasma TV Operation Setup Menu Options EZ Scan (Channel Search) - Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list. - Run EZ Scan again after any Antenna/Cable connection changes. 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select EZ Scan. 3. Press the ENTER button to begin the channel search. Allow EZ Scan to complete the channel search cycle for ANTENNA, and CABLE. Manual Scan 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select Manual Scan. 3. Press the G button and then use CADTV. D /E button to select TV, DTV, CATV, and 4. Press the G button and then use want to add or delete. D /E button to select channel number you 5. Press the ENTER button to add or delete for the channel number. 6. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Notes: • This channel number is a physical channel number, which is different from the normal channel number shown in Channel Edit. • When a cable box connects to the physical channel 2,3 or 4 in the TV Guide On Screen system Setup, cable channels(CATV or CADTV) will not be scanned by EZ Scan or Manual Scan. • When inserting the CableCARDTM, CATV, CADTV is not working in EZ Scan. • TV: analog antenna(over-the-air) TV signal DTV: digital antenna(over-the-air) TV signal CATV: analog cable TV signal CADTV: digital cable TV signal Owner’s Manual 39 Operation Setup Menu Options Channel Edit - Create two different types of channel lists in memory: “Custom list” and “Favorite channel list” from the default channel list created from the EZ Scan channel search. - A custom list can be created by toggling each channel on or off with ENTER button. The. The channels in the Custom List are displayed in black color, and the channels deleted from the Custom List are displayed in gray color. Once a channel is highlighted you can add or delete the channel by referring to the small window at the top-left corner of the screen.You can create your own Favorite List. Use the FAV button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List. 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select Channel Edit. 3. Press the G button. You will now see a screen filled with channel numbers and a preview picture. 4. Use D / E / F / G button to select a channel and then use the ENTER button to add or delete it. Press FAV button to add the channel to the Favorite List. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note: • When a cable box connects to the physical channel 2, 3, or 4 in TV Guide On Screen Setup, cable channels(CATV or CADTV) will not be editable by Channel Edit. Instead, use the cable box's Channel Edit if available. DTV Signal Strength - Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation. - DTV Signals: Only when the input signal is DTV or CADTV, this function is available. 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select DTV Signal. 3. View the on-screen signal strength monitor to see the quality of the signal being received. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 40 Plasma TV Operation Channel Label Setup - Choose preset labels for your channels. - If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn't preset a label for the channel. 1. Press the MENU button and then use 2. Press the G button and then use D /E D /E button to select the SETUP menu. button to select Channel Label. 3. Press the G button. You will now see a screen filled with Labels and a preview screen. 4. Use the CH +/- button to select a channel to Label. 5. Use D / E / F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to the selected channel. - If you press ENTER button, you will see the channel banner. Main Picture Source Selection - Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV. 1. Press the MENU button and then use D 2. Press the G button and then use D /E /E button to select the SETUP menu. button to select Main Input. 3. Press the G button and then use D / E button to select the source: Antenna, Cable, Video, Front Video, Component1, Component2, RGB-DTV (or RGBPC), HDMI1/DVI, HDMI2. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Input Label 1. Press the MENU button and then use D 2. Press the G button and then use D /E /E button to select the SETUP menu. button to select Input Label. 3. Press the G button and then use D / E button to select the source: Video, Front Video, Component1, Component2, RGB, HDMI1/DVI or HDMI2. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owner’s Manual 41 Operation V ideo Menu Options EZ Picture - EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category. - When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Custom. - Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at the factory and are not adjustable. 1. Press the EZ PIC button repeatedly to select the picture appearance setup option as shown below: Custom (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports. • You can also use the VIDEO menu to adjust EZ Picture. 2. Press the EXIT button to save and return to TV viewing. Manual Picture Control ( Custom option) - Adjust the picture appearance to suit your preference and viewing situations. 1. Press the MENU button and then use D /E button to select the VIDEO menu. 2. Press the G button and then use D / E button to select the desired picture option (Contrast, Brightness, Color, Sharpness, or Tint ). 3. Press the G button and then use F / G button to make appropriate adjustments. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Color Temperature Control - Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E 3. Press the G button and then use D Warm. /E button to select the VIDEO menu. button to select Color Temperature . button to select either Cool, Medium or 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. V ideo Reset - Use to quickly reset all the Video menu options to their original factory preset values. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the VIDEO menu. button to select Video Reset . 3. Press the G button to reset the Video menu options to original values. 42 Plasma TV Operation Audio Menu Options Audio Language - Other languages may be available if a digital signal is provided by the broadcasting station. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D /E button to select Audio Language. 3. Press the French. D /E button to select: English, Spanish, or button and then use 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. EZ SoundRite - Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the button and then use D /E button to select EZ SoundRite. 3. Press the button and then use D /E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. EZ Sound - EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content. - When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Custom. - Normal, Stadium, News, Music, and Theater are preset for good sound quality at the factory and are not adjustable. 1. Press the EZ SOUND button repeatedly to select the appropriate sound setup as shown below: Custom (your own settings), Normal, Stadium, News, Music, and Theater. • You can also adjust EZ Sound in the AUDIO menu. 2. Press EXIT button to save and return to TV viewing. Owner’s Manual 43 Operation Audio Menu Options Manual Sound Control ( Custom option) - Adjust the sound to suit your taste and room situations. 1. Press the MENU button and then use D /E button to select the AUDIO menu. 2. Press the G button and then use D (Balance, Treble, or Bass). /E button to select the desired sound option 3. Press the G button and then use F /G button to make appropriate adjustments. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Front Surround is a trademark of SRS Labs, Inc. - TruSurround XT technology is incorporated under license from SRS Labs, Inc. - Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. 1. Press the MENU button and then use D 2. Press the button and then use D /E /E button to select the AUDIO menu. button to select Front Surround. 3. Press the G button and then use D / E button to select Off, 3D EchoSound System or SRS (Sound Retrieval System) TruSurround XT.. • 3D EchoSound System Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage into stereo sound. • SRS TruSurround XT Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 44 Plasma TV Operation TV Speakers On/Off On/Off Setup - Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the button and then use D /E button to select TV Speaker. 3. Press the button and then use D /E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Stereo/SAP Broadcasts Setup - This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the station transmits an additional sound signal as well as the original one. - When having selected Stereo or SAP button on the remote control, this TV can only receive the signal in case that the TV station transmits the proper signals. - Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected. - Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting. - Stereo or SAP can be received in Analog channel. 1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono, Stereo, or SAP appear in turn. • If other languages available on the digital signal, select them with the SAP button. 2. Press EXIT button to save and return to TV viewing. BBE - BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism. 1. Press the MENU button and then use D /E 2. Press the button and then use D /E button to select BBE. 3. Press the button and then use D /E button to select On or Off. button to select the AUDIO menu. 4. Press EXIT button to return to TV viewing or press ENTER button to return to the previous menu. Manufactured under license from BBE Sound, Inc. Owner’s Manual 45 Operation T ime Menu Options Auto Clock Setup The time is set automatically from a digital channel signal. The digital channel signal includes information for the current time provided by the broadcasting station. Set the clock manually, if the current time is set incorrectly by the auto clock function. When you set up TV guide on screen system, Auto Clock menu is not selected. 1. Press the MENU button and then use menu. D /E button to select the TIME 2. Press the button and then use D /E button to select Auto Clock. 3. Press the button and then use D /E button to select On. 4. Press the G button and then use D / E button to select your viewing area time zone: Eastern, Central, Mountain, Pacific, Alaska, or Hawaii. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Manual Clock Setup - If current time setting is wrong, reset the clock manually. - When you set up TV guide on screen system, Manual Clock menu is not worked. 1. Press the MENU button and then use 2. Press the button and then use D /E D /E button to select the TIME menu. button to select Manual Clock. 3. Press the G button and then use F / G button to select either the year, date, or time option. Once selected, use the D / E button to set the year, date, and time options. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. On/Off On/Off Timer Setup Timer function operates only if current time has been set. Off-Timer function overrides On-Timer function if they are set both set to the same time. The TV must be in standby mode for the On-Timer to work. If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode. 1. Press the MENU button and then use D /E 2. Press the G button and then use D button to select Off Timer or On Timer. /E button to select the TIME menu. 3. Press the G button and then use D / E button to select On. • To cancel On/Off timer function, select Off. 4. Press the button and then use D /E button to set the hour. 5. Press the button and then use D /E button to set the minutes. 6. For only On timer function Press the G button and then use D / E button to select the channel at turn-on. Press the G button and then use D / E button to set the sound level at turnon. 7. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 46 Plasma TV Operation Sleep Timer - The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. - You can also set up the Sleep Timer in the TIME menu. 1. Press the TIMER button repeatedly to select the number of minutes. First the Off option appears on the screen, followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes. 2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to count down from the number of minutes selected. 3. To check the remaining minutes before the TV turns off, press the TIMER button once. 4. To cancel the Sleep Timer, press the TIMER button repeatedly to select Off. Auto Off Off - If set to on and there is no input signal, the TV turns off automatically after 10 minutes. 1. Press the MENU button and then use D / E button to select the TIME menu. 2. Press the G button and then use D / E button to select Auto Off. 3. Press the G button and then use D /E button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owner’s Manual 47 Operation Option Menu Features TimeShift Mode - See Page 71~72 for TimeShift functions. Cinema 3:2 Mode Setup - Set up the TV for the best picture appearance for viewing movies. 1. Press the MENU button and then use D /E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Advanced. 3. Press the G button and then use D / E button to select Cinema 3:2 Mode. 4. Press the G button and then use D / E button to select On or Off. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Low Power - Low power reduces the plasma display power consumption. 1. Press the MENU button and then use 2. Press the G button and then use D 3. Press the G button and then use D 4. Press the button and then use D /E button to select the OPTION menu. / E button to select Advanced. / E button to select Low power. D /E button to select On or Off. • When you select On, the screen darkens. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 48 Plasma TV Operation LG Logo - This function is only applied to 60PY2DR model. 1. Press the MENU button and then use D /E button to select the OPTION menu. 2. Press the button and then use D /E button to select LG Logo. 3. Press the button and then use D /E button to select On or Off. • When you select On, the Logo is lighting. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owner’s Manual 49 Operation Option Menu Features Aspect Ratio Control - Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed. - If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option. - Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/HDMI1/DVI-DTV (720p/1080i)/DTV(720p/1080i) input source. - RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio. - Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and remain visible. 1. Press the RATIO button repeatedly to select the desired picture format. You can also adjust Aspect Ratio in the OPTION menu. • Set By Program Selects the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9) • 4:3 Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides. • 16:9 Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen. • Horizon Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view. • Zoom 1 Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped. • Zoom 2 Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage. • Cinema Zoom Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted. You can adjust the enlarge proportion of Cinema Zoom using D / E button. The adjustment range is 1~16. 50 Plasma TV Operation Caption 1. Press the MENU button and then use menu. 2. Press the G button and then use 3. Press the G button and then use D /E D /E D / E button to select the OPTION button to select Caption. button to select On or Off. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Caption/Text Caption/Text Analog Broadcasting System Captions Select a caption mode for displaying captioning information if provided on a program. Analog caption displays information at any position on the screen usually the program's dialog. Text displays information, usually at the bottom position and is used for a data service, generally not program related. Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable. This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off. 1. Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. • EZ Mute shows the selected captions option (if available on program) when the TV sound is muted .2. Press EXIT button to save and return to TV viewing. • You can also use the OPTION menu to select Caption/Text. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption/Text. 3. Press the G button and then use D / E button to select caption: CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4. • CAPTION The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired. • TEXT The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owner’s Manual 51 Operation Option Menu Features Digital Broadcasting System Captions - Choose the language you want the DTV/CADTV Captions to appear in. - Languages can be chosen for digital sources only if they are included on the program. 1. Press the MENU button and then use D / E button to select the OPTION menu. 2. Press the G button and then use D / E button to select Caption/Text. 3. Press the G button and then use D / E button to select available caption languages: English, Spanish, or French. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Caption Option - Customize the DTV/CADTV captions that appear on your screen. button to select the OPTION 1. Press the MENU button and then use menu. D /E 2. Press the G button and then use D /E button to select Caption Option. 3. Press the G button and then use F /G button to select Custom. 4. Use D / E button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language. • Size: Set the size the words will appear in. • Font: Select a typeface for the words. • Text Color: Choose a color for the text. • Text Opacity: Specify the opacity for the text color. • Bg (Background) Color: Select a background color. • Bg (Background) Opacity: Select the opacity for the background color. • Edge Type: Select an edge type. • Edge Color: Select a color for the edges. 5. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. 52 Plasma TV Operation ISM (Image Sticking Minimization) Method - A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screen for a long period of time. 1. Press the MENU button and then use menu. 2. Press the button and then use D /E 3. Press the G button and then use D wash, Orbiter or Inversion . /E D / E button to select the OPTION button to select ISM Method. button to select either Normal, White • Normal If image sticking is never a problem, ISM is not necessary - set to Normal. • White wash White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button. • Orbiter Orbiter may help prevent ghost images. However, it is best not to allow any fixed image to remain on the screen. To avoid a permanent image on the screen, the image will move once per minute: Right → Right → Downside → Downside → Left → Left → Upside → Upside. • Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Front Display - Illuminates brightly when the set is turned on. The LED displays current TV status. - This function is only applied to 50/60PY2DR model. 1. Press the MENU button and then use menu. D /E 2. Press the G button and then use button to select Front Display. D /E 3. Press the G button and then use D /E button to select the OPTION button to select Off, Dark and Bright. 4. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Owner’s Manual 53 Operation Option Menu Features Auto Demo - Displays the slide show to explain the main features of this TV. 1. Press the MENU button and then use menu. D /E 2. Press the button to select Auto Demo. button and then use D /E 3. Press EXIT button to stop Auto Demo. 54 Plasma TV button to select the OPTION Operation Lock Menu Options Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1. Set ratings and categories to be blocked. 2. Specify a password 3. Enablethe lock V-Chip rating and categories Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only. Ratings for Movies previously shown in theaters: Movie Ratings : • Blocking Off (Permits all programs) •G (General audience) • PG (Parental guidance suggested) • PG-13 (Parents strongly cautioned) •R (Restricted) • NC-17 (No one 17 and under admitted) •X (Adult only) If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked. Ratings for Television programs including made-for-TV movies : • TV-G • TV-PG • TV-14 • TV-MA • TV-Y • TV-Y7 (General audience) (Parental guidance suggested) (Parents strongly cautioned) (Mature audience only) (All children) (Children 7 years older) TV Rating Children: • Age • Fantasy Violence (applies to TV-Y, TV-Y7) (applies to TV-Y7) TV Rating General: • Age • Dialogue - sexual dialogue • Language - adult language • Sex - sexual situations • Violence (applies (applies (applies (applies (applies to TV-G, TV-PG, TV-14, TV-MA) to TV-PG, TV-14) to TV-PG, TV-14, TV-MA) to TV-PG, TV-14, TV-MA) to TV-PG, TV-14, TV-MA) Input Block • Video, Front Video (On, Off) • Component 1, 2 (On, Off) • RGB, HDMI1/DVI,HDMI2 (On, Off) Owner’s Manual 55 Operation Lock Menu Options Parental Lock Setup - Set up blocking schemes to block specific channels, ratings, and external viewing sources. - A password is required to gain access to this menu if the Lock System is turned on. 1. Press the MENU button and then use D Then, press the G button /E button to select the LOCK menu. • If Lock is already set, enter the password as requested. • The TV is set up with the initial password “0-0-0-0”. 2. Use the D / E button to choose from the following Lock Menu options. Once the option is selected, change the settings to your preference. • Lock System: Activates or disables the blocking scheme you set up previously. • Set Password: Change the password by inputting a new password twice. • Block Channel: Blocks any channels that you do not want to watch or that you do not want your children to watch. • Movie Rating (MPAA): Blocks movies according to the movie ratings limits specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas. • TV Rating-Children: Prevents children from watching certain children's TV programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs. • TV Rating-General: Based on the ratings, blocks certain TV programs that you and your family do not want to view. • Input Block: Enables you to select a source to block from the external source devices you have hooked up. 3. Press EXIT button to return to TV viewing or press MENU button to return to the previous menu. Note: • If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control. 56 Plasma TV Operation Recorded TV - When you press the button, HOME menu is displayed. From here, you can view the recorded program list. - Or pressing the REC LIST button, you directly enter the recording list. 1. Select the Recorded TV in HOME menu or press the REC LIST button to view the recording list as shown below. A. B. 3. Select the desired folder in the folder list and then press the ENTER button to view the detailed menu. • Create: Create new folder. • Delete: Delete folder (except ‘My TV’). • Rename: Edit folder name. • Cancel: Close the detailed menu. C. -> Use the D / E / F / G button to input the wanted name. -> And then move the OK and press the ENTER button to save. Owner’s Manual 57 Operation Recorded TV D. - The current thumbnail recorded list is shown above. 1. Use the CH +/- button to navigate thumbnail photo in pages. 2. Use MARK button to add or delete the marked photo to the mark list and only marked photos are toggling. 3. Use D / E / F / G button to navigate the appropriate thumbnail photo, then press the ENTER button to open the pop-up menu. • Play: Begin playback of selected recording. • Mark All: mark all photos on the screen. • Unmark All: Change marked photos to unmarked photos. • Move: Move program saved in HDD to the other folder. • Through the 1394, can be recorded the desired program. When a device is not connected to the 1394 port, “No DVHS Connected” is dis-played on the screen. • Delete: Delete the selected recording. This menu is only available in HDD mode. • DVHS Out: When DVHS is connected, selected program is saved to the DVHS. • Rename: Edit recorded name. • Cancel: Close the Pop-up menu. 4. Repeatedly, press REC LIST button or EXIT button to return to TV viewing or press previous menu. button to return to the - If the HDD has a problem on performing a function (Recording, Photo, Music) related with DVR, question both Yes or No which being displayed this message to initialize HDD as shown below. - If you selects Yes, it can be deleted the Recorded List, Photo/Music list etc. because of initializing HDD. Even If you selects No, it can't be worked DVR operation of playback, record etc. - If temperature is below zero(0°), this message is displayed to initialize HDD as shown below. 58 Plasma TV Operation On playing the recorded program, play - You can play the selected program in the recorded program list. 1.Play a recorded program. 2.On playing, You can see a diversified playback screen as shown below. • At first, it is showed as marking .Then press the ENTER button to display the progress bar. • To disappear a recorded program icon, press the EXIT button. * The ‘Progress Bar’? This function indicates a possible DVR reshowing section ,a current on-screen and real onbroadcasting position, a section of section-recording. 1. Indicates movement of recorded program. 2. Indicates status of recorded program. 3. Indicates elasped playback time. 4. Indicates total playback time. 5. Indicates 15 minute intervals from recorded program start time. (Total - one hour). 6. Indicates current playback position. Using the remote control - You can shift playback to any point within playing the recorded program - When playing, press the REW (FF ) or FF (GG) button. • Like -> -> -> -> in a row. 2 times 5 times 20 times 50 times 300 times • If the button is pressed continuously, it changes like above. If the button is taken away, it changes a normal playback. (In the condition of not setting a section to repeat) - If you wish to return to a initial portion of playback program, press the (In the condition of not setting a section to repeat) - If you wish to return to a last portion of playback program, press the button. button. - Press the PLAY (G) button to return to a normal playback. - During playback, press the Pause ( II ) button. • Still screen is displayed. • Repetedly press the Pause ( II ) button to advance frame by frame. • When pressing the Pause ( II ) button, longly, will be showed. • Unless a remote control input after a pause, return to the condition of playback in 15 minutes. • If you press the D / E button on piaying, the screen will be jumped back and forth in the current screen. • Pressing the D button, the screen will be jumped 20 seconds in the front. • Pressing the E button, the screen will be jumped 8 seconds in the back. • After moving to the back using the G button on playing, press the the be directly returned to the prior screen. button to - If you press the STOP ( J ) button, you can watch the TV. • After marking the “ J ”, this program is ended in 15 minutes. Owner’s Manual 59 Operation Recorded TV On playing the recorded program, edit a section - You can save the desired screen in the recorded program list after editing the recorded program.. 1. At the point of desired start , press the button. • The progress bar which be editied will be showed the red color. • It can be possible as search (FF or GG 2. At the point of desired finish , press the • Stop editing the section. ), pause while editing the section. button. 3. Repeatedly play the above 1,2 phase, it can be possible to edit some programs. 4. If you press the button to stop the recorded program playback, this message is displayed as shown below. • Save: Save contents of editing the section and finish the playback of recorded program. • Undo: Don’t save contents of editing the section and finish the playback of recorded program. • Cancel: The screen is disappeared and the playback is continued. Notes: • It can be possible to play on the recording / reserved recording • It can be possible to occur a noise by a hard-disk on playing the recorded program. The noise is irrelevant the proficiency and creditability of product, the noise occurred more than adequate is the same as good product. • In case saving the content of editing the section, delete the portion not to select. • When power off on editing, It can be possible not to save the content of editing. You do press the STOP ( after checking the recording list. • Editing the section can be possible to the maxium of 10. • You can not save editing of less than 10 seconds. 60 Plasma TV J ) button v On playing the recorded program, repeat a section - You can set the section and repeatedly view on playig the recorded program. 1. At the point of desired start, press the • At start points, it is showed as marking button. 2. At the point of desired finish, press the button. • At finiah points, it is showed as marking • Repeatedly play the marked section. • You can not make sections of less than 5 seconds. • The progress bar which be repeated will be showed the blue color. 3. Press the button to move the position of the start point. • Return to the start point of marked section and then start the playback. 4. If you press the or button to stop playing the repeat section. Notes: • It can be possible a function as search (Rew / FF), Pause, edit a section while repeating a section. • When setting the section of start and finish, it can be possible both of Rew and FF. Owner’s Manual 61 Operation Notes on Memory Card What is Memory Card This is a device equipment to communicate the data between AV external equipment. It’s used to a digital camera, camcorder, MP3 player, notebook or PDA. Precaution for Using the Memory Card - Insert the memory card correctly. - Don’t insert the metal substances into the slots of the memory card. - Do not bend, drop or apply strong shock to memory card. - After pulling the memory card out from the TV, please keep the memory stick in a appropriate case to prevent static shock. - The stored data may be changed or lost as a result of misuse, static electricity. - Do not turn the power off while using the memory card (loading or erasing). - Don’t eject the memory card while using the it. Otherwise, it may cause a data loss or card damage. - Only Insert one card to each slot. - To prevent a change or loss for stored data, don’t misuse the TV or don’t let static electricity or electrical noise for TV. - This Company takes no responsibility for problems such as the damage or malfunction that occurs while using the TV set, inappropriate TV settings, or any other reasons, except for defects or malfunctions intrinsic to the product. - Ensure to use a memory card that lists the manufacturers name and serial number. - The manufacturer shall not be responsible for damaged data. Be careful to avoid data damage, and back up your files. - Make sure to comply with the following steps when ejecting a memory card. - Each Memory Card is complied with standard. 62 Plasma TV Operation Entry Modes- 1.Using the Memory Card / 2. Enter the HOME Menu 1.Using the Memory Card How to insert and eject the Memory Card 50/60PY2DR 50PX4DR A. label-side upward Inserting a Card 1. Insert the Memory Card to Memory card slots of TV side panel. 2. Two slots support defferent types of the Memory Cards. 3. If Memory Card is not inserted, each slot is disable. Ejecting a card 1. Press the M/C EJECT button on the remote control. 2. Select the Slot 1 or Slot 2 based on the inserted card location. If selecting Cancel, OSD is disappeared. 3. Eject the card with the hand. Note: If you insert or eject a card in one slot while the card in another slot (slot 1 or slot 2) is in use, the product can run abnormally. Caution: Before you remove the memory card from the slot, do not forget to press the M/C EJECT button on the remote control and make it safe to eject the memory card, or the memory card may be damaged. Owner’s Manual 63 Operation Notes on Memory Card Memory Card type and Memory Card capacity - 9 types of Memory Card can be used for this Plasma TV. - Playback speed can vary dependent on the card type. -Unsupported or damaged photo or music files can cause errors. Do not try to change the file extension of unsupported file --types to the file extension of supported file types. Slot 1 • • • Slot 2 • • • • • • CF (CompactFlash) : 4GB MD (Microdrive) : 4GB CF+|| (MagicStor) :2.2GB *MagicStor Plus card is not is complied with the TV. MultiMediaCardTM TM Secure Digtal SmartMedía 64 Plasma TV xD-Picture Card MEMORY STICK CompactFlash MEMORY STICK PRO magicstor Microdrive SD (Secure Digital) : 1GB MMC (MultiMedia Card) : 1GB MS (Memory Stick) :128MB MS Pro (Memory Stick Pro) : 1GB SMC (Smart Media Card) : 128MB xD (xD-Picture Card) : 512MB Operation Select the Photo or Music - When you plug the Memory Card, this screen is displayed, automatically. C. B. 1. Press the F / G button to select Photo/Music. and use D / E button to select Slot1 or Slot2. 2. Press ENTER button to move to Photo List/Music List of the each slot. (Directly move to p.59,(C)) Note: In 30 seconds later, 'Loading" message is disappeared. - 2.Enter the HOME Menu Photo List - When you press the button, HOME menu is displayed. It’s available to playback and copy the Photo file of Memory Card.or HDD. The total storage space of photo file is 10GB. 1. In HOME menu, use D / E button and then use the ENTER or G button to select the Photo List . A. D / E button to select the HDD/ Memory Card 1/ Memory Card 2 and then you will see a screen filled with 2. Use thumbnail photos (pic.C,D). Owner’s Manual 65 Operation Photo List Screen Components Marked thumbnail photo number Current page/Total page B. Card type Usable Card memory Usable HDD Folder List Direct Buttons Folder List C. D. 3. Select the desired folder in the folder list and then press the ENTER button to view the detailed menu. • Create: Create new folder. • Delete: Delete folder (except ‘My Photo' ).. • Rename: Edit folder name. • Cancel: Close the detailed menu. E. -> Use the D / E / F / G button to input the wanted name. -> And then select OK and press the ENTER button to save. 66 Plasma TV
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Page Count : 66 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:e05d5889-852f-481c-bd61-ce239b29ffd9 Producer : Acrobat Distiller 6.0 (Windows) Modify Date : 2005:03:11 20:40:39+09:00 Create Date : 2005:03:11 20:40:39+09:00 Creator Tool : QuarkXPressª3.3E: LaserWriter 8 Z1-8.7.1 Document ID : uuid:28bfcb43-a80d-4f2a-bcb1-cd1a5e3e9d91 Format : application/pdf Title : 528Aen(TU-50PY22)-1 Creator : PSY Author : PSYEXIF Metadata provided by EXIF.tools