LG Innotek RBDAG332A Bluetooth Full Module for Automotive User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2109163
Application ID	o/Dr632N8QEA+nuG+ZHeJA==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	42.25kB (528183 bits)
Date Submitted	2013-11-01 00:00:00
Date Available	2014-04-30 00:00:00
Creation Date	2013-10-22 16:27:57
Producing Software	Microsoft® PowerPoint® 2010
Document Lastmod	2013-10-31 10:21:59
Document Title	슬라이드 제목 없음
Document Creator	Microsoft® PowerPoint® 2010
Document Author:	박인표

• User Manual
Description
- Model : RBDA-G332A
- Profile : Hands free(1.6), A2DP (1.2), AVRCP (1.4)
- Bluetooth: v3.0+EDR
- Frequency Range : 2402MHz ~ 2480MHz
Features
- Dimension : 35.3 X 35.3 X 7.8mm
- Temperature Range : -40℃ ~ +85℃
- Supply Voltage : VREGIN – 3.1V to 3.6V
- Output Power
BT: Typ. 1dBm(Class 2)
- Sensitivity
BT: -80dBm
Interface
-. BT: UART, I2S
Application
Automotive
Dimensions
PART NO.
NAME
MATERIAL
SPEC
FINISH
SIZE
1.0.1 `13.10.10
Deployment
NO. Changes
UNIT SCALE
LG Innotek Co, Ltd
DRAW DSGD CHKD
APPD
Choi
Kim
Park
TITLE
User Manual(1/5)
DOCUMENT NO.
RBDA-G332A(FCC)
* Power Supply Specification
The power of DC3.1V ~ 3.6V is should be supplied to the Bluetooth module power(VDD). The
module supplies the power to the each block depending on the function. Module input power in
excess of the rated input power may cause damage to the internal components. And the influx of
Surge and ESD also may lead to the damage of the modem in the vehicle. For the prevention of this,
the module is necessary to design block the infloux of Sugre and EDS.
Pin NO.
Signal Name
Function
(Module case)
MIN
TYP
MAX
13.14
VDD
In
3.1V
3.3V
3.6V
* Data Tx/Rx Specification
The Bluetooth modules communicates with other bluetooth devices using Bluetooth communication
technology. It has the data buffer used to receive and process data transmitted at 625㎲ time
intervals defined in the Bluetooth specification from the remote device. This buffer is enough to
process the data sent at the ideal speed(3Mbps). Additionally in order to prevent the buffer overflow,
the module could control the transmission by the flow control scheme defined in the Bluetooth
specification.
* UART ( RS-232 Interface )
The module has the UART interface to communicate with other serial devices using the RS232
protocol. the UART parameters such as the packet format and baud rate are configured by the
module firmware.
PART NO.
NAME
MATERIAL
SPEC
FINISH
SIZE
1.0.1 `13.10.10
Deployment
NO. Changes
UNIT SCALE
LG Innotek Co, Ltd
DRAW DSGD CHKD
APPD
Choi
Kim
Park
TITLE
User Manual(2/5)
DOCUMENT NO.
RBDA-G332A(FCC)
General Features
RBDA-G332A satisfies the following standards
1)Griffin Bluetooth Module Features
• Bluetooth Power Class 2
• Bluetooth v3.0 + EDR Compliant
• Support for Wide-Band Speech.
• Embedded Fully Bluetooth v2.0/v2.1 + EDR System Compliant
• Embedded Bluetooth Profile
• Embedded AEC/NR Algorithm for Hands-free
• Embedded 16-bits Stereo CODEC
• Operation Voltage is 3.3V Single Power Rail
• Excellent Compatibility with Cellular Telephones
• Command and data Interface is UART
• Audio Input/Output Interface is I2S
• Support Software update by UART
• Support for 802.11 Co-existence
• RoHS Compliant
2) Functionality Key Features : 2.1+EDR
• Secure simple pairing
• Sniff sub-rating
• Encryption pause resume
• Packet boundary flags
• Encryption
• Extended inquiry response
3) Functionality Key Features : 2.0+EDR
• Adaptive frequency hopping (AFH), including classifier
• Faster connection - enhanced inquiry scan (immediate FHS response)
• LMP improvements
• Adaptive Frequency Hopping (AFH) as Master and Automatic Channel Classification
• Fast Connect-Interlaced Inquiry and Page Scan plus RSSI during Inquiry
• Extended SCO (eSCO), eV3 +CRC, eV4, eV5 • SCO handle
• Synchronization
4) Support Profiles
• GAP
• HFP : 1.6
• A2DP : 1.2
• AVRCP : 1..4
• PBAP : 1.1
• MAP : 1.0
• SPP : 1.1
PART NO.
NAME
MATERIAL
SPEC
FINISH
SIZE
1.0.1 `13.10.10
Deployment
NO. Changes
UNIT SCALE
LG Innotek Co, Ltd
DRAW DSGD CHKD
APPD
Choi
Kim
Park
TITLE
User Manual(3/5)
DOCUMENT NO.
RBDA-G332A(FCC)
PIN Description
PART NO.
NAME
MATERIAL
SPEC
FINISH
SIZE
1.0.1 `13.10.10
Deployment
NO. Changes
UNIT SCALE
LG Innotek Co, Ltd
DRAW DSGD CHKD
APPD
Choi
Kim
Park
TITLE
User Manual(4/5)
DOCUMENT NO.
RBDA-G332A(FCC)
PIN Description
PART NO.
NAME
MATERIAL
SPEC
FINISH
SIZE
1.0.1 `13.10.10
Deployment
NO. Changes
UNIT SCALE
LG Innotek Co, Ltd
DRAW DSGD CHKD
APPD
Choi
Kim
Park
TITLE
User Manual(5/5)
DOCUMENT NO.
RBDA-G332A(FCC)
RSS-GEN 7.1.3 User manual Notice for Licence-Exempt Radio Appartus.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device.
L'exploitation est autoris e aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi,
m me si le brouillage est susceptible d'en compromettre le fonctionnement.
FCC Statement
FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation
FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly
approved by the manufacturer may void the user's authority to operate the equipment.
Part 15.105 (B)
Note : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications, However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void your authority to
operate the equipment under FCC rules.
RF Exposure Statement (2.1091)
FCC RF Radiation Exposure Statement: FCC RF Radiation Exposure Statement: This
equipment complies with FCC RF Radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction
with any other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20cm between
the radiator and your body.
RF du FCC d'exposition aux radiations: Cet équipement est conforme à l'exposition de la FCC
rayonnements RF limites établies pour un environnement non contrôlé. L’antenne pour ce
transmetteur ne doit pas être même endroit avec d’autres émetteurs sauf conformément à la
FCC procédures de produits Multi-émetteur.
Cet équipement doit être installé et utilisé avec une distance minimale de 20cm entre le
radiateur et votre corps.
* Information for OEM integrator
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user manual of the end product.
The user manual which is provided by OEM integrators for end users must include the
following information in a prominent location.
“To comply with FCC RF exposure compliance requirements, the antenna used for this
transmitter must be installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter.”
Label for end product must include “Contains FCC ID: YZP-RBDAG332A, IC: 7414ARBDAG332A" or “ A RF transmitter inside, FCC ID: YZP-RBDAG332A, IC: 7414ARBDAG332A”.
* Information pour les OEM intégrateur
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
concernant la façon d'installer ou de retirer ce module RF dans le manuel utilisateur du produit
final.
Le manuel de l'utilisateur qui est fourni par les intégrateurs OEM pour les utilisateurs finaux
doivent inclure les renseignements suivants dans un endroit bien en vue.
«Pour se conformer aux exigences de conformité d'exposition RF de la FCC, l'antenne utilisée
pour ce transmetteur doit être installé pour fournir une distance de séparation d'au moins 20 cm
de toute personne et ne doit pas être co-localisés ou fonctionnant en conjonction avec une autre
antenne ou transmetteur. "
Étiquette pour le produit final doit inclure "Contient FCC ID: YZP-RBDAG332A, IC: 7414ARBDAG332A" ou "A l'intérieur du transmetteur RF, FCC ID: YZP-RBDAG332A, IC:
7414A-RBDAG332A".

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : 박인표
Create Date                     : 2013:10:22 16:27:57+09:00
Modify Date                     : 2013:10:31 10:21:59+09:00
Has XFA                         : No
Language                        : ko-KR
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : 박인표
Title                           : 슬라이드 제목 없음
Creator Tool                    : Microsoft® PowerPoint® 2010
Metadata Date                   : 2013:10:31 10:21:59+09:00
Producer                        : Microsoft® PowerPoint® 2010
Document ID                     : uuid:5f0c93d6-829b-4e89-84eb-c914a1c1b113
Instance ID                     : uuid:1ef1f14c-0d9c-4c14-a432-f3e7db788082
Page Count                      : 7

EXIF Metadata provided by EXIF.tools