LG Innotek REBEMZ42A Electronic Shelf Label User Manual User Manaual

Download:
Mirror Download [FCC.gov]
Document ID	2619941
Application ID	PaRpIrTYCZvHYnA4iXFBLw==
Document Description	User Manaual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	43.04kB (538000 bits)
Date Submitted	2015-05-20 00:00:00
Date Available	2015-05-20 00:00:00
Creation Date	2015-04-21 14:51:36
Producing Software	Microsoft® PowerPoint® 2010
Document Lastmod	2015-05-19 10:39:35
Document Title	PowerPoint 프레젠테이션
Document Creator	Microsoft® PowerPoint® 2010
Document Author:	user

2015.04.19
ELS 4.2 Mono Graphic Type Manual
Ver. 0.1
1. ELS Description & Key사내한
Function
 Remote control device provides customer with several functions as below
 Waking Tag up from sleep mode
 Updating new purchase image on Tag
 Deleting purchase image on Tag
 Returning a Tag to be factory settings
Display Area
Profile Hook
Battery Cover
 Remo-con description

LED : One of any buttons is pushed, green led turns on.
After sending some data to a Tag, green led will turn off.

Registration : Updating New Purchase Information on Tag

Release : Deleting Purchase Information on Tag

Reset : Returning a Tag to be factory settings

Keep Alive : Waking Tag up from sleep mode
: This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Caution: Any changes or modifications to the equipment not expressly approved by the party
responsible for
compliance could void user’s authority to operate the equipment.
This appliance and its antenna must not be co-located or operation in conjunction with any other
antenna or transmitter.
A minimum separation distance of 20 ㎝ must be maintained between the antenna and the person for
this appliance to satisfy the RF exposure requirements.
Copyrightⓒ. 2015. All Rights Reserved.
사내한
2. “Registration” Key Function
☜
To change purchase information on Tag, perform the following steps :
1.
Put remote controller near center of Tag‟s display
2.
Press and hold „Registration‟ button on remote controller until green LED off
(about 0.5 seconds)
3.
When Tag is successfully received „Registration‟ data from remote controller,
Tag‟s display will be changed to “Connected” for a few minutes.
That means Tag hides purchase image to read Tag‟s IEEE MAC address through
the Barcode scanner
4.
In NMS Client, download new purchase image to the Tag in registration status
5.
When image downloading is finished successfully,
Tag‟s display will be changed to new purchase image
Copyrightⓒ. 2015. All Rights Reserved.
3. “Release” Key Function사내한
☜
To release(delete) purchase information on Tag, perform the following steps :
1.
Put remote controller near center of Tag display
2.
Press and hold „Release‟ button until green LED off (about 0.5 seconds)
3.
If Tag was received „Reset‟ command from remote controller,
Tag will delete purchase information and Tag‟s display will be changed to “Ready”
4.
After step.3, Tag goes to deep sleep mode and doesn‟t communicate with gateway
until receiving „Keep Alive‟ or „Registration‟ data from remote controller
Copyrightⓒ. 2015. All Rights Reserved.
사내한
4. “Keep Alive” Key Function
Case 1
Case 2
☜
Case 3
To wake Tag up from sleep mode, perform the following steps :
1.
Put remote controller near center of Tag display
2.
Press and hold „Keep Alive‟ button until green LED off (about 0.5 seconds)
3.
Tag will wake up and goes to next step. It‟s depends on connection information with gateway
case1) If this Tag wasn‟t connected with a gateway before sleep mode, go to 4-1
case2) If this Tag was connected with a gateway before sleep mode, go to 4-2
4-1. Searching gateway and goes to the next step. it‟s depends on searching results
case1) If Tag was successfully connected, Tag‟s display will be changed to “Ready”
case2) If Tag wasn‟t connected, Tag‟s display(may be “Ready”) will be refreshed
4-2. Sending „Keep Alive‟ packet to gateway and Tag will go to sleep mode again
Copyrightⓒ. 2015. All Rights Reserved.
5. “Reset” Key Function
사내한
☜
To make a Tag to be factory reset status, perform the following steps :
1.
Put remote controller near center of Tag display
2.
Press and hold „Reset‟ button until green LED off (about 0.5 seconds)
3.
If Tag was received „Reset‟ command from remote controller,
Tag goes back to factory settings and Tag‟s display will be changed to “Ready”
4.
After step.3, Tag goes to deep sleep mode and doesn‟t communicate with gateway
until receiving „Keep Alive‟ or „Registration‟ data from remote controller
Copyrightⓒ. 2015. All Rights Reserved.
6. Status Display
사내한
Deep Sleep mode
Connected to gateway
Disconnected to gateway
Image downloading fail
Battery is dis-charged (to need changing battery)
Copyrightⓒ. 2015. All Rights Reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Language                        : ko-KR
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : user
Title                           : PowerPoint 프레젠테이션
Create Date                     : 2015:04:21 14:51:36+09:00
Creator Tool                    : Microsoft® PowerPoint® 2010
Modify Date                     : 2015:05:19 10:39:35+09:00
Metadata Date                   : 2015:05:19 10:39:35+09:00
Producer                        : Microsoft® PowerPoint® 2010
Document ID                     : uuid:75cd45d9-8812-474d-87df-69b33d93daa4
Instance ID                     : uuid:8660a7a5-861e-4047-a57a-5217975d5fce
Page Count                      : 7
Author                          : user

EXIF Metadata provided by EXIF.tools