LG Innotek REBETZ15D Electronic Shelf Label User Manual Users manual

LG Innotek Co., Ltd. Electronic Shelf Label Users manual

Users manual

Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek 1.54 ” 3 Color Graphic type ESL User manual
Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek Remote control device provides customer with several functions as below Waking Tag up from sleep mode Updating new purchase image on Tag Deleting purchase image on Tag Returning a Tag to be factory settings 1. Overview Remo-con description Release : Deleting Purchase Information on Tag Keep Alive : Waking Tag up from sleep mode Reset : Returning a Tag to be factory settings Registration : Updating New Purchase Information on Tag LED : One of any buttons is pushed, red led turns on. After sending some data to a Tag, red led will turn off. Display Area Profile Hook Battery Cover A remote controller or a NFC Device contact point for communication.
Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek To change purchase information on Tag, perform the following steps : 1. Put remote controller near center of Tag‟s display 2. Press and hold „Registration‟ button on remote controller until Red LED off (about 0.5 seconds) 3. When Tag is successfully received „Registration‟ data from remote controller, Tag‟s display will be changed to “Connected” for a few minutes. That means Tag hides purchase image to read Tag‟s IEEE MAC address through the Barcode scanner. 4. In NMS Client, download new purchase image to the Tag in registration status 5. When image downloading is finished successfully, Tag‟s display will be changed to new purchase image Case1) If image downloading is failed, Tag‟s display will be changed to “Busy”. After “Alive Time”, this Tag will be download new purchase image again 2. Updating new purchase image on Tag ☜
Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek To release(delete) purchase information on Tag, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold „Release‟ button until red LED off (about 0.5 seconds) 3. If Tag was received „Reset‟ command from remote controller, Tag will delete purchase information and Tag‟s display will be changed to “Ready” 4. After step.3, Tag goes to deep sleep mode and doesn‟t communicate with gateway until receiving „Keep Alive‟ or „Registration‟ data from remote controller 3. Deleting purchase information on Tag ☜
Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek To wake Tag up from sleep mode, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold „Keep Alive‟ button until Red LED off (about 0.5 seconds) 3. Tag will wake up and goes to next step. It‟s depends on connection information with gateway case1) If this Tag wasn‟t connected with a gateway before sleep mode, go to 4-1 case2) If this Tag was connected with a gateway before sleep mode, go to 4-2 4-1. Searching gateway and goes to the next step. it‟s depends on searching results case1) If Tag was successfully connected, Tag‟s display will be changed to “Ready” case2) If Tag wasn‟t connected, Tag‟s display(may be “Ready”) will be refreshed 4-2. Sending „Keep Alive‟ packet to gateway and Tag will go to sleep mode again case1) If Tag was received response from gateway, this Tag will go to “sleep mode” until the specified time in gateway. After “sleep mode”, this Tag will send “Keep Alive” Packet to gateway again. case2) If Tag wasn‟t received response from Gateway, this Tag will retry three times. After that, Tag‟s display will be changed to “Disconnected”. Also this Tag will perform a whole channel scan every five minutes. . 4. Waking Tag up Image 2 ☜ Image 1
Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek To make a Tag to be factory reset status, perform the following steps : 1. Put remote controller near center of Tag display 2. Press and hold „Reset‟ button until Red LED off (about 0.5 seconds) 3. If Tag was received „Reset‟ command from remote controller, Tag goes back to factory settings and Tag‟s display will be changed to “Ready” 4. After step.3, Tag goes to deep sleep mode and doesn‟t communicate with gateway until receiving „Keep Alive‟ or „Registration‟ data from remote controller case1) If Tag was received “Keep Alive” or “Registration” command from remote controller, this Tag will perform a whole channel scan. case2) If Tag was received “Reset” or “Release” command from remote controller, Tag‟s display will be changed to “Ready” again 5. Returning a Tag to be factory settings ☜ 2016.10.20 14:34:59 353,003
Copyrightⓒ. 2017. All Rights Reserved. Confidential LG Innotek 6. Tag status Symbol Mode Image Deep Sleep Mode Connected with Gateway Disconnected with Gateway Battery discharge (the battery needs to be replaced) Image download Failure(“Busy”)
Copyright ⓒ 2015. All Rights Reserved. LG Innotek Confidential LG Innotek Confidential 7. Regulation Information

Navigation menu