LG Innotek REBETZ42B Electric Shelf Label User Manual

LG Innotek Co., Ltd. Electric Shelf Label

User Manual

Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG Innotek4.2 ” 3-color Graphic type ESLUser manual
Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG InnotekRemote control device provides customer with several functions as below Waking Tag up from sleep modeUpdating new purchase image on TagDeleting purchase image on TagReturning a Tag to be factory settings1. OverviewRemo-con descriptionDisplay AreaProfile Hook Battery CoverRelease : Deleting Purchase Information on TagKeep Alive : Waking Tag up from sleep modeReset : Returning a Tag to be factory settingsRegistration : Updating New Purchase Information on TagLED : One of any buttons is pushed, red led turns on.After sending some data to a Tag, red led will turn off.
Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG InnotekTo change purchase information on Tag, perform the following steps :1. Put remote controller near center of Tag’s display2. Press and hold ‘Registration’ button on remote controller until Red LED off (about 0.5 seconds)3. When Tag is successfully received ‘Registration’ data from remote controller, Tag’s display will be changed to “Connected” for a few minutes. That means Tag hides purchase image to read Tag’s IEEE MAC address through the Barcode scanner.4. In NMS Client, download new purchase image to the Tag in registration status5. When image downloading is finished successfully, Tag’s display will be changed to new purchase image Case1) If image downloading is failed, Tag’s display will be changed to “Busy”. After “Alive Time”, this Tag will be download new purchase image again☜☜☜☜2. Updating new purchase image on Tag
Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG InnotekTo release(delete) purchase information on Tag, perform the following steps :1. Put remote controller near center of Tag display2. Press and hold ‘Release’ button until red LED off (about 0.5 seconds)3. If Tag was received ‘Reset’ command from remote controller, Tag will delete purchase information and Tag’s display will be changed to “Ready”4. After step.3, Tag goes to deep sleep mode and doesn’t communicate with gateway until receiving ‘Keep Alive’ or ‘Registration’ data from remote controller☜☜☜☜3. Deleting purchase information on Tag
Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG InnotekTo wake Tag up from sleep mode, perform the following steps :1. Put remote controller near center of Tag display2. Press and hold ‘Keep Alive’ button until Red LED off (about 0.5 seconds)3. Tag will wake up and goes to next step. It’s depends on connection information with gatewaycase1) If this Tag wasn’t connected with a gateway before sleep mode, go to 4-1case2) If this Tag was connected with a gateway before sleep mode, go to 4-24-1. Searching gateway and goes to the next step. it’s depends on searching resultscase1) If Tag was successfully connected, Tag’s display will be changed to “Ready”case2) If Tag wasn’t connected, Tag’s display(may be “Ready”) will be refreshed4-2. Sending ‘Keep Alive’ packet to gateway and Tag will go to sleep mode again case1) If Tag was received response from gateway, this Tag will go to “sleep mode” until the specified time in gateway. After “sleep mode”, this Tag will send “Keep Alive” Packet to gateway again.case2) If Tag wasn’t received response from Gateway, this Tag will retry three times. After that, Tag’s display will be changed to “Disconnected”. Also, this Tag will perform a whole channel scan every five minutes..4. Waking Tag upCase 2Case 3☜☜☜☜
Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG InnotekTo make a Tag to be factory reset status, perform the following steps :1. Put remote controller near center of Tag display2. Press and hold ‘Reset’ button until Red LED off (about 0.5 seconds)3. If Tag was received ‘Reset’ command from remote controller, Tag goes back to factory settings and Tag’s display will be changed to “Ready”4. After step.3, Tag goes to deep sleep mode and doesn’t communicate with gateway until receiving ‘Keep Alive’ or ‘Registration’ data from remote controllercase1) If Tag was received “Keep Alive” or “Registration” command from remote controller, this Tag will perform a whole channel scan.case2) If Tag was received “Reset” or “Release” command from remote controller, Tag’s display will be changed to “Ready” again5. Returning a Tag to be factory settings☜☜☜☜
Copyrightⓒ. 2015. All Rights Reserved.ConfidentialLG Innotek6. Tag statusDeep Sleep ModeConnected with GatewayDisconnected with GatewayImage download Failure(“Busy”)Battery discharge(The battery needs to be replaced)
Copyright ⓒ 2015. All Rights Reserved. LG Innotek Confidential LG Innotek Confidential 7/4 7. Regulation Information

Navigation menu