LG Innotek TWFML006D Wi-Fi Module User Manual users manual

LG Innotek Co., Ltd. Wi-Fi Module users manual

users manual

User ManualPRODUCT NAME : Dual Band 2T2R MIMO Wi-Fi ModuleMODEL NAME : TWFM-L006D(00)-0073The information contained herein is the exclusive property of LG Innotekand shall not be distributed, reproduced or disclosed in whole or no in partwithout prior written permission of LG Innotek.
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.1 / 11Table of ContentsNo Description Page1 Features 22 Module Photo 23 Block Diagram 34 Storage Test Conditions 45 Operating Test Conditions 46 Software Programming 57 Pin Description 78 Outline Drawing 89 Packing Information 9
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.2 / 112. Module Photo1. FeaturesTWFM-L006D is the module for IEEE 802.11a/b/g/n wireless LAN. TWFM-L006D is based on MTK RT5572 solution.IEEE 802.11 a/b/g/n Dual Band WLAN infrastructureSize : 40mm x46.5mm x 8.25mm2.4GHz and 5GHz, internal PA and LNATwo stream spatial multiplexing up to 300MbpsMetal Press AntennaUse on-chip OTP (One-Time Programmable)USB 2.0Supports drivers for Linux, WindowsSecurity : WPA,WPA2,AES(TKIP) ,IEEE 802.1X • Application: DTV, DVR, HD DVD Player, Blue-ray Disk Player, STB
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.3 / 113. Block DiagramDPXANT0RT5572USB I/F 6Pin Connector802.11n MACMain Clock (40MHz)PALNA802.11nPHYSecurityE-Fuse(2K byte)Internal BusGPIOUSB 2.03.3VDC-DC(1.5MHz) 5VANT1ReceiverTransmitterDPX1.5VPALNA
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.4 / 11Parameter Min Max UnitStorage Temperature -20 +80 ℃Storage Humidity (@ 40℃) - 90 %Caution : The specifications above the Table define levels at which permanent damage to the device can occur. Function operation is not guaranteed under these conditions. Operating at absolute maximum conditions for extend periods can adversely affect the long-term reliability of the device.• Other conditions1) Do not use or store modules in the corrosive atmosphere, especially where chloridegas, sulfide gas, acid, alkali, salt or the like are contained. Also, avoid exposure to moisture. 2) Store the modules where the temperatureand relative humidity do not exceed 5 to 40℃and 20 to 60%.3) Assemble the modules within 6 months.Check the soldering ability in case of 6 months over.4. Storage Test ConditionsParameter Min Typ Max UnitOperating Temperature 0 - +60 ℃Operating Humidity (40℃) - - 85 %Supply Voltage 4.5 5.0 5.5 Vdc5. Operating Test Conditions
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.5 / 116. Software Programming1) Windows UtilityExecute the released windows utility installer.(1) Run RaUI.exe(2) RaUI can co-exist with WZC. When coexisting with WZC, RaUI only providesmonitoring functions, such as surveying the link status, network status, staticcounters, advanced features status, WMM status and WPS status.(3) When starting RaUI, the system will connect to the AP with best signal strength without setting a profile or matching a profile setting. It will issuea scan command to a wireless NIC. After two seconds, the AP list will be updated with the results of a BSS list scan. < Fig1.1 RaUI icon>< Fig1.2 Select WZC and RaUI>< Fig1.3 RaUI section introduction>
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.6 / 11(4) Button section.- Site survey, Link information, Profile, Advanced, Information, About page.- Help page.(5) When starting RaUI, a small Ralink icon appears in the notifications area of the taskbar, as shown in <Fig1.5>.* Please refer to the help page in detail usage manual.2) Linux Device DriverBefore compiling the driver, you should change make file or makefile.inc to meetyour target platform.* Please refer to the release note in detail.< Fig1.4 Button section>< Fig1.5 Ralink icon in system tray>
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.7 / 117. Pin DescriptionPin No. Pin Name I/O Pin Description1 VDD I VDD 5.0V2 USB_DN I/O USB Communication signal USB_DN3 USB_DP I/O USB Communication signal USB_DP4 GND - GND5 WoWLAN I Wake on Wireless LAN6 GND - GND< Top View >Note.1) Recommend a Module install sequence for prevent USB device failure- Supply 5.0V power - Connect to data signal (USB_DP, USB_DN)2) Connector : Connector A1257WR0-6PSAA1 6
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.8 / 118. Outline Drawing
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.9 / 119. Packing Information9-1. Inner Box Packing
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.10 / 119-2. Carton Box Packing
User ManualPAGE :REG. DATE : 2013.12.13MODEL NAME : TWFM-L006DREV. DATE : 2013.12.13REV.NO : 1.0©2013 LGIT. All rights reserved.11 / 119-3. Pallet Packing
FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures: 1.1. Reorient or relocate the receiving antenna. 1.2. Increase the separation between the equipment and receiver. 1.3. Connect the equipment into an outlet on a circuit different from that to which receiver is connected. 1.4. Consult the dealer or experienced radio/TV technician for help. WARNING Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. “CAUTION : Exposure to Radio Frequency Radiation. Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation. The antenna should not be contacted during operation to avoid the possibility of exceeding the FCC radio frequency exposure limit. IC Information This device complies with Industry Canada license-exempt RSS standard(s). Operation in subject to The following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada RSS standard exempts de licence(s), Son utilisation est soumise à Les deux conditions suivantes: (1) cet appareil ne peut pas provoquer d’interférences et (2) cet appareil doit accepter Toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. ¼ This device is going to be operated in 5 150 MHz ~ 5 250 MHz frequency range, it is restricted in indoor environment only.
Information for OEM Integrator The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. End product labelling The label for end product must include “Contains FCC ID: YZP-TWFML006D”. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Navigation menu