LINAK A S DPG1B DPG Desk Panels User Manual
LINAK A/S DPG Desk Panels
user manual
Page 1 of 28
To learn more about LINAK, please visit:
www.linak.com
USER MANUAL
DPG Desk panels and
Desk Control Apps
Page 2 of 28
Page 3 of 28
Contents
Preface................................................................................................................................ 4
Important information .................................................................................................... 5
Safety instructions ........................................................................................................... 5
Only for EU markets ......................................................................................................... 8
Only for Non EU markets ................................................................................................ 8
Misuse ............................................................................................................................... 8
Informations importantes ............................................................................................... 9
Consignes de sécurité ...................................................................................................... 9
Seulement pour les marchés au sein de l´UE .............................................................. 10
Seulement pour les marchés hors UE .......................................................................... 10
Utilisation abusive ......................................................................................................... 10
Repairs ............................................................................................................................. 11
Declaration of incorporation of partly completed machinery ................................. 11
Misc. on the DESKLINE® system ................................................................................... 12
Warranty ..................................................................................................................... 12
Maintenance ............................................................................................................... 12
ETL-marking .................................................................................................................... 12
Products .......................................................................................................................... 13
Operation of the DPG series ........................................................................................ 14
Operation of the DPG1M .............................................................................................. 15
Operation of the DPG1B/C ........................................................................................... 20
Placement of the DPG1K/M .......................................................................................... 27
Placement of the DPG1B/C ........................................................................................... 28
Mounting of the DPG ................................................................................................... 29
Preparing the tabletop for both DPG sizes .................................................................... 30
Bluetooth® Adapter ....................................................................................................... 32
How to put the adapter in pairing mode ....................................................................... 33
Desk Control .................................................................................................................. 34
Disposal of LINAK’s products ...................................................................................... 45
Drawing appendix ......................................................................................................... 46
Labels .............................................................................................................................. 49
Declaration of Conformity ........................................................................................... 50
LINAK application policy .............................................................................................. 51
Addresses ....................................................................................................................... 52
Page 4 of 28
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and
development of actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the
manufacturer of the equipment or system only, and it will tell you how to install, use and maintain
your LINAK electronics. It is the responsibility of the manufacturer of the end-use product to provide a
User Manual where relevant safety information from this manual is passed on to the end-user.
We are sure that your LINAK product will give you many years of problem-free operation.
Before our products leave the factory they undergo full function and quality testing. Should you
nevertheless experience problems with your systems, you are always welcome to contact your local
dealer.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres,
which are always ready to help you.
LINAK provides a warranty on all its products. This warranty, however, is subject to correct use in
accordance with the specifications, maintenance being done correctly and any repairs being carried
out at a service centre, which is authorised to repair LINAK products.
Changes in installation and use of LINAK systems can affect their operation and durability. The
products are not to be opened by unauthorised personnel.
The User Manual has been written based on of our present technical knowledge. We are constantly
working on updating the information and we therefore reserve the right to carry out technical
modifications.
LINAK A/S
Page 5 of 28
Safety instruction
General
Important information
Important information on LINAK® products can be found under the following headings:
Warning!
Failure to comply with these instructions may result in accidents involving serious
personal injury.
Failing to follow these instructions can result in the product being damaged or
being destroyed.
Safe use of the system is possible only when the operating instructions are read completely
and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in serious
damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to have the
necessary information and access to this User Manual. Follow the instructions for
mounting – risk of injury if these instructions are not followed.
The appliance is not intended for use by young children or infirm persons without
supervision.
If there is visible damage on the product it must not be installed.
Note that during construction of applications, in which the actuator is to be fitted,
there must be no possibility of personal injury, for example the squeezing of fingers
or arms.
Assure free space for movement of application in both directions to avoid blockade.
Page 6 of 28
This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and
(2) This device must accept any
interference received, including
interference that may cause
undesired operation
• Statement – for all intentional and unintentional radiators:
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
• Statement for digital devices for Class B:
NOTE: This equipment has been tested and found to comply with the limits for a Class
B diwgital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions it may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
Page 7 of 28
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil nedoit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
Labeling Requirements:
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Page 8 of 28
Only for EU markets
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not
be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the product/
products must not use the product/products. Besides, persons with reduced physical,
sensory or mental abilities must not use the product/products, unless they are under
surveillance or they have been thoroughly instructed in the use of the apparatus by
a person who is responsible for the safety of these persons.
Moreover, children must be under surveillance to ensure that they do not play with
the product.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a table
while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use
Page 9 of 28
Consignes de sécurité
Géneral
Informations importantes
Les informations importantes sur les produits LINAK® peuvent être trouvées dans les
rubriques suivantes:
Attention!
Le non respect de ces instructions peut entraîner des accidents impliquant des
blessures graves.
Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du
produit.
Le non respect de ces instructions peut entraîner des accidents impliquant des blessures
graves.
Ne pas suivre ces instructions peut entraîner l´endommagement ou destruction du produit.
L´utilisation en toute sécurité du système n´est possible que si l´intégralité des instructions
ont été lues et ont été strictement suivies.
Le non respect de se conformer aux instructions marquées du symbole “note” peut
entraîner de graves dommages au système ou à un de ses composants.
Il est important pour tout individu qui connecte, installe, ou utilise le système d´avoir
les informations nécessaires et l´accès à ce mannuel d´utilisation.
Suivez les instructions pour le montage – risque de blessure si ces instructions ne
sont pas suivies.
L´appareil n´est pas destiné à être utilisé par des enfants ou des personnes
handicapées sans surveillance.
S´il y a des dommages visibles sur le produit, l´installation ne doit pas être effectuée.
Prendre en compte lors de la construction du matériel, dans lequel l´actionneur est
incorporé, qu´il ne doit y avoir aucune possibilité de blessures corporelles, telles que
la compression des doigts ou des bras.
Assurez un espace libre autours du materiel pour éviter tout blocage.
Page 10 of 28
Seulement pour les marchés au sein de l´UE:
Cet appareil peut-être utilisé par des enfants âgés de 8 ans et plus, ainsi que les
personnes dont les capacités physiques, sensorielles ou mentales sont réduites
ou ayant un manque d´expérience et de connaissance si elles ont bénéficié d´une
surveillance ou d´instructions concernant l´utilisation de l´appareil en toute sécurité et
compris les risques encourus.
Les enfants ne doivent pas jouer avec l´appareil. Le nettoyage et l´entretien ne
doivent pas être rèalisés par des enfants sans surveillance.
Seulement pour les marchés hors UE.
Les personnes qui n´ont pas l´expérience ou les connaissances nécessaires sur le
ou les produit(s) ne doivent pas le ou les utiliser. Par ailleurs, les personnes ayant
des capacités physiques, sensorielles ou mentales réduites ne doivent pas utiliser
le ou les produit(s), sauf si elles sont sous surveillance ou ont suivi une formation
approfondie de l´utilisation de l´appareil par l´individu responsable de la securité de
ces personnes.
De plus, les enfants doivent-être sous surveillance afin de s´assurer qu´ils ne jouent
pas avec le produit.
Utilisation abusive:
Ne surchargez pas les actionneurs – cela peut engendrer un risque de blessures
corporelles et endommager le système.
Ne pas utiliser les actionneurs pour soulever des personnes. Ne pas s´asseoir ou se
tenir debout sur une table en fonctionnement – risque de blessures.
Ne pas utiliser le système dans dans des environnements autres que l´utilisation
intérieure prévue.
Page 11 of 28
Repairs
In order to avoid the risk of malfunction, all DESKLINE® repairs must only be carried out by authorised LINAK®
workshops or repairers, as special tools must be used and special gaskets must be fitted. Lifting units under
warranty must also be returned to authorised LINAK workshops.
Warning!
If any of the DESKLINE® products are opened, there will be a risk of subsequent malfunction.
Warning!
The DESKLINE® systems are not resistant to cutting oil.
DECLARATION OF INCORPORATION OF PARTLY COMPLETED MACHINERY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
Herewith declares that LINAK DESKLINE® products as characterized by the following models and types:
Control Boxes CBD4, CBD6S
And
Linear Actuators LA31, DB4, DB5, DB6, DB7, DB9, DB12, DB14, DB16, LA23
Lifting Columns DL1A, DL2, DL4, DL5, DL6, DL7, DL8, DL9, DL10, DL11, DL12, DL14, DL15,
DL16, DL17, LP2, LP3, BASE1
And
Desk Panels DP, DPA, DPB, DPH, DPF, DPT, DP1C, DP1K, DP1L, DP1V, DP1U, WDPL1
RF Controls HB10, HB20, RFR and RFT
And
Accessories SLS
comply with the following parts of the Machinery Directive 2006/42/EC, ANNEX I, Essential health and
safety requirements relating to the design and construction of machinery:
1.5.1 Electricity supply
The relevant technical documentation is compiled in accordance with part B of Annex VII and that this
documentation or part hereof will be transmitted by post or electronically to a reasoned request by the
national authorities.
This partly completed machinery must not be put into service until the final machinery into
which it is to be incorporated has been declared in conformity with the provisions of the
Machinery Directive 2006/42/EC where appropriate.
Nordborg, 2014-04-10
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
Original Declaration
Page 12 of 28
Misc. on the DESKLINE® system
Warranty
There is a 60 months’ warranty on the DESKLINE products when used in DESKLINE applications against
manufacturing faults from the production date of the individual products. LINAK A/S’ warranty is only valid in so
far as the equipment has been used and maintained correctly and has not been tampered with. Furthermore, the
system must not be exposed to violent treatment. In the event of this, the warranty will be ineffective/invalid. For
further details, please see LINAK A/S’ ordinary conditions of sale.
Maintenance
Clean dust and dirt on the outside of the system at appropriate intervals and inspect for damage and breaks.
Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points.
The cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).
ETL-marking
Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.
The full ETL Recognized Component markings are shown here.
C/N 120690
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008003
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008004
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 9901916
Conforms to ANSI/AAMI Std. ES60601-1
Cert. to CSA Std. C22.2 No. 60601-1
ETL Recognized Component mark for Canada and United States
C/N 4008671
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
Page 13 of 28
Desk Control Apps
• Up and down drive
(if supported by the connected product)
• Displays actual height
• Displays error codes and links to LINAK website
support
• Up to 4 memory positions
• Tracks usage of the desk
• Reminder notifications to get standing
• Possibility to enable automatic drive on memory
positions (if supported by the connected product)
• Works via Bluetooth® Low Energy Technology
• Available in English, German, French, Spanish,
Italian, Korean, Chinese and Japanese
DPG1K
• Up/down drive
Products
DPG1M
• Up/down drive
• 2 memory positions
• LED diode reminder
• Bluetooth®
DPG1B
• Up/down drive
• 2 memory positions
• Light strip reminder
• Bluetooth®
DPG1C
• Up/down drive
• 4 memory positions
• Light strip reminder
• Bluetooth®
• Display
Page 14 of 28
Operation of the DPG series:
The desk panel is operated by tilting; Tilt and hold the DPG up to make the desk drive up, press and hold the
DPG down to make the desk drive down. Release the DPG when you have reached your requested position.
Figure 1: Tilt and hold the DPG1K to make the desk drive up
Figure 2: Press and hold the DPG1K to make the desk drive down
Page 15 of 28
Operation of the DPG1M
Storing the memory positions
Memory positions
The DPG1M has a “store memory” button to the right symbolised with a star.
Adjust the desk to a preferred position and press the “Star”-button for 2 seconds. The LED will now blink white
two times to indicate that saving the position is in progress. When the LED becomes static white, the position
is saved. If the user adjusts the desk to another position and saves the position, it will overwrite the memory
position closest to the current position.
Page 16 of 28
Driving to memory positions
After storing the memory positions, the positions can be reached simply by tilting the DPG1M. Tilt and hold
- when a stored position is reached, the desk stops. This way the user can easily change between sitting and
standing position without looking at the DPG1M in the meantime. The DPG1M will stop at all stored memory
positions. When the desk stops at a memory position, the user can continue to tilt the DPG1M for 1 second
and the desk will move past the memory position and continue in the direction of the tilt. Furthermore, when
the desk stops at a memory position, the user can release the DPG and tilt again immediately to move past a
memory position.
Driving to memory positions (Automatic drive enabled, only possible for “Full version”)
After storing the memory positions, the positions can be reached simply by tilting the DPG1M. Double tab on the
DPG1M to let the desk adjust automatically to the first position in the direction of the double tap. Simply tab the
DPG again to stop the driving of the desk.
Figure 3: Double tap to adjust the desk to a memory position automatically
Page 17 of 28
Erase memory positions
Pressing the “Memory” button for 8 seconds will erase all saved memory positions. The LED will blink red to
indicate when the action is completed.
Connecting Bluetooth®
Pressing the Bluetooth® button in the middle for 2 seconds will enable pairing mode.
A blue blinking light in the LED indicates this.
Download the Desk Control App suited for your device in App, Google Play or Windows store and pair the app
and device.
Page 18 of 28
Reminder
Setting the reminder interval
The DPG1M has a “Reminder” button to the left symbolised with a bell. Pressing this button will adjust the
interval of how often to get reminders to change position. The LED will light up in 3 different intensities which
each represents an interval and the 3 standards are:
- Interval 1: Reminder after 55 minutes sitting
- Interval 2: Reminder after 50 minutes sitting
- Interval 3: Reminder after 45 minutes sitting
The default interval chosen is reminding after 55 mins, which means the LED will be lit up white in the weakest
intensity. Simply toggle through the intervals by pressing the bell button and notice the light intensity change.
When the LED is not lit up, the reminder is turned off.
Through the apps, it is possible to personalise the three intervals to custom values.
Setting reminder interval. Reminder off
Reminder reset
It is possible to reset the reminder to default values by pressing the “bell” symbol for 8 seconds. The LED will
blink red to indicate when the action is completed.
Page 19 of 28
LED reminder
The LED is placed in the lower left corner of the DPG1M. The LED is intended to indicate the status of the desk
user. The status depends on the reminder interval chosen. When the user is in position in an appropriate amount
of time according to the interval, the LED calmly pulsates green. When the sitting interval runs out, the calm
pulsating green turns into fast pulsating orange for 1 min hereafter static orange – this is an indication to the
user to adjust the desk to standing height. In standing height, the LED will pulsate green until a potential time
out. When the desk is adjusted back to sitting position, the LED will pulsate green until the reminder goes off
again.
After 4 hours without any action, the LED will time out. When the DPG1M is tilted, the green light will come
back on.
Please be aware; When the LED is enabled for reminders, the DPG1M is no longer in ZERO mode as long
as the light is on/active.
Factory reset
Pressing and holding the “Memory” and “Reminder” for 8 seconds will set the DPG1M to factory default. The
LED will flash red 3 times.
Figure 4: Pulsating green LED indicates everything is okay
Figure 5: Pulsating orange LED indicates the user needs to change position
Page 20 of 28
Operation of the DPG1B/C
The desk panel is operated by tilting; Tilt and hold the DPG up to make the desk drive up, press and hold the
DPG down to make the desk drive down. Release the DPG, when you have reached your requested position.
Figure 1: Tilt and hold the DPG to make the desk drive
Figure 2: Press and hold the DPG to make the desk drive down
Page 21 of 28
Storing the memory positions
Memory positions 1 and 2
The DPG1B/C have a “store memory” button to the right symbolised with a star.
Adjust the desk to a preferred position and press the “Star”-button for 2 seconds. The light strip will now blink
white two times to indicate that saving the position is in progress. When the light strip becomes static white,
the position is saved. In the DPG1C: The display will indicate the saved position with a star and a number of the
position. The number inside the star is according to in which order the positions are saved; First position saved;
A star with a “1” inside. This is how to save the 2 memory positions “1” and “2”. If the user adjusts the desk
to another position and saves the position, it will overwrite the memory position 1 or 2 closest to the current
position.
DPG1C: Memory positions 3 and 4
The DPG1C features 4 memory positions. Pressing the “Star” shortly will make the display show the 4 memory
positions: A “star” with the number next to it. Now the user can toggle through these 4 memory positions in
the display and choose which one to save the current position as. E.g. a user wants to store the current position
as memory 3: Press the “star”-button and toggle to the “star” with “3” next to it. Now use the same storing
procedure as described above: Press the star for 2 seconds and the memory position is saved.
Page 22 of 28
Driving to memory positions
After storing the memory positions, the positions can be reached simply by tilting the DPG. Tilt and hold - when
a stored position is reached, the desk stops. This way the user can easily change between sitting and standing
position without looking at the DPG in the meantime. While driving the display in the DPG1C will show the
height of the desk. When a position is reached, this will be indicated in the display by the star and the memory
number.
The DPG will stop at all stored memory positions, which means up to 4 different positions (in DPG1C) during the
stroke length of the desk. When the desk stops at a memory position, the user can continue to tilt the DPG for 1
second and the desk will move past the memory position and continue in the direction of the tilt. Furthermore,
when the desk stops at a memory position, the user can release the DPG and tilt again immediately to move
past a memory position.
Driving to memory positions (Automatic drive enabled, only possible for “Full version”)
After storing the memory positions, the positions can be reached simply by tilting the DPG. Double tab on the
DPG to let the desk adjust automatically to the first position in the direction of the double tap. Simply tab the
DPG again to stop the driving of the desk.
Figure 3: Double tap to adjust the desk to a memory position automatically
Page 23 of 28
Erase memory positions
Pressing the “Memory” button for 8 seconds will erase all saved memory positions. In the DPG1C: The display
will make a countdown and the light strip will blink red to indicate when the action is completed.
Connecting Bluetooth®
Pressing the Bluetooth® button in the middle for 2 seconds will enable pairing mode.
A blue blinking light in the light strip indicates this.
Download the Desk Control App suited for your device in App, Google Play or Windows store and pair the app and device
The display on the DPG1C will inform about the Bluetooth-ID of the desk, which is “DESK” followed by a 4-digit number –
look for this ID in the list of “Desks nearby”.
Page 24 of 28
Reminder
Setting the reminder interval
The DPG has a “Reminder” button to the left symbolised with a bell. Pressing this button will adjust the interval
of how often to get reminders to change position. Each white block represents an interval and the 3 standards
are:
- Interval 1: Reminder after 55 minutes sitting
- Interval 2: Reminder after 50 minutes sitting
- Interval 3: Reminder after 45 minutes sitting
The default interval chosen is reminding after 55 mins, which means one white block will be lit up. Simply toggle
through the intervals by pressing the bell button. When no white blocks are lit up, the reminder is turned off.
Through the apps, it is possible to personalise the three intervals to custom values.
Interval 1: Reminder after 55 minutes sitting Interval 2: Reminder after 50 minutes sitting
Interval 3: Reminder after 45 minutes sitting Reminder off
Reminder reset
It is possible to reset the reminder to default values by pressing the “bell” symbol for 8 seconds. The display will
make a countdown and the light strip will blink red to indicate when the action is completed.
Page 25 of 28
Light strip reminder
The light strip is a thin line of LED light shining through the surface of the DPG. The light strip is intended to
indicate the status of the desk user. The status depends on the reminder interval chosen. When the user is in
position in an appropriate amount of time according to the interval, the light strip calmly pulsates green. When
the sitting interval runs out, the calm pulsating green turns into fast pulsating orange for 1 min hereafter static
orange – this is an indication to the user to adjust the desk to standing height. In standing height, the light strip
will pulsate green until a potential time out. When the desk is adjusted back to sitting position, the light strip
will pulsate green until the reminder goes off again.
After 4 hours without any action, the light strip will time out. When the DPG is tilted, the green light will come
back on.
Please be aware; When the light strip is enabled for reminders, the DPG is no longer in ZERO mode as
long as the light is on/active.
Figure 4: Pulsating green light strip indicates everything is okay
Figure 5: Pulsating orange light strip indicates the user needs to change position
Page 26 of 28
Factory reset
Pressing and holding the “Memory” and “Reminder” for 8 seconds will set the DPG to factory default. The light
strip will flash red 3 times. In the DPG1C: After 3 seconds of the command, the display will light up: It has an
arrow with a countdown [seconds] to the factory reset and it says RESET.
DPG1C
Display
The DPG1C has an OLED display, which shows the height during drive of the desk and many other texts to guide
the user.
Adjust initial height of the desk
If the height shown in the display is not correct the height can be adjusted. When pressing the “Reminder” and
the “Bluetooth” button on the DPG1C at the same time in 5 seconds; the height in the display starts to blink.
When tilting the DPG1C the height in the display changes without moving the desk. Tilt up to increase the
height, tilt down to decrease the shown height in the display. Pressing any button will confirm the choice or wait
for 10 seconds and the confirmation happens automatically.
Switching between centimetre and inch
Pressing the “Memory” and the “Bluetooth” button on the DPG1C at the same time for 5 seconds; the current
measurement unit blinks. When e.g. CM is blinking and the user wants to change to inch; Tilt the DPG once and
it now says “Inch” in the display. Pressing any button will confirm the choice or wait for 10 seconds and the
confirmation happens automatically.
Error codes
The DPG1C shows error codes in case of errors in the system. The most common errors loop between the error
code (EXX) and the cause, check the code below:
Error codes in CBD6S Cause
E01 INITIALISATION
Page 27 of 28
Placement of the DPG1K/M:
The drawings below are side views examples on how to position the DPG1K/M according to the edge of the
tabletop.
Drawing No.: DRW0001
Drawing No.: DRW0001
Page 28 of 28
Placement of the DPG1B/C:
The drawings below are side views examples on how to position the DPG1B/C according to the edge of the
tabletop. Because of the light strip, we recommend placing the DPG1B/C in a visible position.
Drawing No.: DPG1B_BORDPL
Drawing No.: DPG1B_BORDPL
Page 29 of 28
Mounting of the DPG:
When mounting the DPG it is important to ensure that the cable is not tightened, but has free mobility in the
first centimetres from the housing. We recommend attaching the cable to the tabletop with a clip as shown on
the picture below:
When mounting the DPG to the tabletop screws with following spec must be used:
- Ø4.5 mm
- 90° countersink screw
Do not use screws with a milling head as this will cut into the housing of the DPG.
The screws must be fastened sufficiently, without overtightening the screws. It is not possible to mention a
specific torque, as this depends on the type of screw, material of tabletop and whether there are predrilled holes
or not.
We recommend predrilling the holes for the DPG to ensure the same aligned position for every desk.
Figure 6: Cross-sectional view of the DPG screw hole
Drawing No.: DRW0001
Drawing No.: DRW0001
Page 30 of 28
Preparing the tabletop for both DPG sizes (DPG1K/M and DPG1B/C)
The DPG series consists of 4 different desk panels in 2 different sizes. The DPG1K and DPG1M are the same size
and the DPG1B and the DPG1C are the same size.
The two sizes share one hole in the hole pattern, which means 3 predrilled holes in the tabletop will make it
possible to mount both sizes of the DPG and all 4 versions.
Figure 7: Hole pattern of the DPG sizes. The dashed line is the second hole of the DPG1B/C
Drawing No.: DPG_ASSEMBLY_ALL
36 16
21
21
26
Drawing No.: DPG_ASSEMBLY_ALL
DPG1B/C
DPG1K/M
Page 31 of 28
The front hole of all 4 DPG variants are shared; Here indicated by the green line.
As the DPG1K and DPG1M are the same size, they share the hole indicated by the red line.
As the DPG1B and DPG1C are the same size, they share the hole indicated by the black line.
Drawing No.: DPG_ASSEMBLY_ALL
DPG1K
DPG1M
DPG1B
DPG1C
Page 32 of 28
Bluetooth® Adapter
The Bluetooth® Adapter allows you to adjust your LINAK product wirelessly from the Desk Control App. Simply
plug the Bluetooth® Adapter in your DESKLINE® control box and download the app: Your application can now be
adjusted via your smartphone or tablet.
The Bluetooth® Adapter is a very compact unit requiring a minimum of space. No mounting is needed, just plug
in the adapter and you are ready.
Usage:
• Compatible with:
- DESKLINE control boxes CBD6S and CBD4A (Only with SW 77432 or 77474)
• Compatible with Desk Control Apps
• Ambient temperature: +5°C to +40°C
• Storage and transport temperature: -10°C to +50°C
• Complies with FCC ID (PART 15C) and IC (RSS247)
Page 33 of 28
How to put the adapter in pairing mode
1. Plug the Bluetooth® adapter into a powered DESKLINE Control Box
2. The Adapter is now in pairing mode. The pairing mode will last 3 minutes and is indicated by a blue flashing
LED through the transparent plastic.
The adapter will be in pairing mode for 30 seconds every time, you make a short activation of your DESKLINE
application.
Download the software you want in App Store or Google Play store and follow the instructions in the programs.
When searching; All devices will be called BLE2LIN followed by a 4-digit number.
Page 34 of 28
Desk Control
Desk Control is an app developed for users of sit/stand desks. The app allows the user to connect to the desk via
Bluetooth® and will now motivate to use the desk efficiently. The app tracks the usage of the desk shown and
helps the users reach their daily goal by sending reminder notifications on the smart device. By downloading the
“Desk Control” app, the desk user comes one step closer to changing the prolonged sitting behaviour and the
user gets the friendly reminder needed to build a healthy routine during the workday.
The app is available for 4 different platforms: iOS for iPhones and iPads, Android for Android smartphones and
tablets, MacOS for MAC computers and Windows for PCs.
Page 35 of 28
How to download the App for Windows computers:
Step 1: Use your PC to log into Windows store
Step 2: Type “Desk Control” in the search column
Step 3: Select the “Desk Control” app
Step 4: Click install to download the app to your device
How to download the App for Android
Step 1: Use your Android device to log into Google Play Store
Step 2: Type “Desk Control” in the search column
Step 3: Select the “Desk Control” app
Step 4: Click install to download the app to your device
Downloading the App
The apps are called “Desk Control” and have the following app logo in
iTunes, Apple App store, Google Play store and Windows store:
How to download the App for iOS
Step 1: Use your Apple device to log into App store
Step 2: Type “Desk Control” in the search column
Step 3: Select the “Desk Control” app
Step 4: Click install to download the app to your device
How to download the App for MacOS:
Step 1: Use your MAC to log into iTunes store
Step 2: Type “Desk Control” in the search column
Step 3: Select the “Desk Control” app
Step 4: Click install to download the app to your device
Page 36 of 28
Onboarding flow
The first time you start the Desk Control app; An onboarding flow will show to guide the user to the first-time
use of the app.
The two main purposes of the onboarding flow is to inform the user of the benefits of changing posture during
the workday and get the connection between the app and the device established. Pressing “connect to your
desk” on the below screen will lead to the “Pairing Bluetooth®” guide.
Page 37 of 28
Pairing Bluetooth®
To get a functional app, you must have the LINAK Bluetooth® Adapter or
desk panel with integrated Bluetooth® such as DPG1M, DPG1B or DPG1C.
The screen to the left informs the user how to get the product they received
in pairing mode.
The Bluetooth® Adapter must be plugged into the DESKLINE® control box
and it will blink blue and be in pairing mode for 3 minutes.
To set a DPG1M/B/C in pairing mode, the Bluetooth® button in the front of
the desk panel must be pressed for 2 seconds and the light strip or light LED
will blink blue to indicate that it is in pairing mode.
When pressing “Hide pairing guide” the screen with the list of devices in
pairing mode will appear. Press the “connect” button to the right of the
device to pair.
All Bluetooth® Adapters Bluetooth® IDs are named BLE2LIN followed by a
4-digit number.
All DPG desk panel Bluetooth® IDs are named DESK followed by a 4 digit-
number.
Demo: By selecting “Try the demo”, you will get access to explore the
functionality of the Desk Control App but without connection to a product.
After pressing the “connect” button and the connection has been
established successfully, the user will be lead to the “Control” page of the
app.
The following question pops up on the screen, which the user have to
answer.
If the user only uses one desk with this app; Press yes
If the user uses this app for multiple desk; Press no
Page 38 of 28
How to use the app
The Desk Control App consists of 3 different tabs to navigate between; “Control”, “You” and “Settings”
Adjustment of the desk (if supported by connected device)
Statistics of the usage of the desk
All settings
Control
This is the landing page after the Bluetooth® connection is established. The functionality of the control page
depends on the product to which app is connected. The screen below is when the app is connected to a
“full version” of a DPG or Bluetooth® Adapter. When the connection is with a “Limited version” of the DPG
or Bluetooth® Adapter; The adjustment of the desk trough the app will not be possible and the memory
positions will only be for saving the positions not adjusting to them via the app. The graphics will adjust to the
possibilities.
Up/down drive
Moves the application upwards/downwards while pressing and holding the button.
Bluetooth® device
Leads back to “Desks nearby” and lets the user connect to another product in pairing mode
DESK 1234
Current height of the desk
Interactive application drawing
Save up to 4 memory positions
Quick view: Progress in daily goal
Up/down drive of the desk
Bluetooth® device connected
Current height of the desk
Interactive application drawing
Save up to 4 memory positions
Bluetooth® device connected
Quick view: Progress in daily goal
Up/down drive of the desk
Page 39 of 28
You
“You” is the page for setting the daily goal of standing at the desk.
The first time you press the ”You”-tab will require following input:
- Choose a goal of sitting and standing. Choose a predefined one or customise it by pressing the symbol
to the right.
- Choose if the smart device should remind via pop-up notifications when it is time to change position
- Type in height and weight of the user to calculate the calories burned.
With these input given the statistics page is ready for use, see the screen below for features:
First time setup view Choose the sit/stand interval Choose to have
reminder notifications
Type user data in
Current sit/stand goal
Pulsating circle showing
progress in daily goal
Minutes standing today
Change current sit/stand goal
and personal information
Change view from daily to
e.g. weekly statistics
Status on goals from last 5 days
Page 40 of 28
History
When sliding the slider from “Today” to “History”, the complete statistic of the app will be shown. The bars
show the statistics according to the horizontal line, which represents the goal. It is possible to get daily, weekly,
monthly and yearly views by using the slider below the graphs. When mousing over on computers or pressing the
bar on phones, a small window will inform about the amount of standing time and the corresponding calories
for the chosen period.
Daily view: Hourly divided Weekly view: Daily divided
Monthly view: Weekly divided Yearly view: Monthly divided
Page 41 of 28
Settings
Pressing the “Settings” will provide a list of choices:
Change the favourite positions
The favourite positions are stored through the control page. If the user wants to change the height of the stored
positions, it can be done through this menu.
Ways to be reminded
Enable or disable reminder notifications as pop-ups on computers and smartphones.
If supported by the connected product, e.g. the DPG1B, enable or disable the light strip as a reminder function.
Set desk name
Change the name of the connected product. The renaming will only affect the local name in the smartphone or
computer - not in the DPG or Bluetooth® Adapter.
Set desk height
Set the current height of the desk. An illustration guides the user on how to measure. Choose in which units the
height is shown: cm or inches.
Page 42 of 28
I use one desk only
Choose between “Yes” or “No”.
Yes: This is the only desk, you use and to which you connect your app. Your reminder and memory settings
are stored in the DPG on the desk.
No: You connect to several desks. Your reminder and memory settings are stored on your smart device and
when you connect to a desk, the settings will reflect in the DPG. When you are no longer connected,
the DPG will go back to the settings it had before you connected after 2 hours
Automatic drive
Enable automatic drive on memory positions. The user has to accept the terms in the pop-up, before this feature
can be enabled. This feature can only be enabled in the “full versions” of the DPG1M/B/C and BLE2LIN, not the
“limited versions”. An animation shows the user how this feature works.
Set language
Choose between 8 different languages in the app. This change does not affect the language in the display of a
DPG1C.
Benefits of changing posture
An overview of some of the benefits by using a sit/stand desk and changing posture.
Terms & conditions
Terms & conditions for using the Desk Control app.
About
Use your desk
Link to “Made to Move”; Get guidance on how to use a sit/stand desk correctly.
Product information
Link to LINAK website with information about this app.
Support
Link to LINAK website with troubleshooting videos on the DPG products.
Page 43 of 28
Reminder notifications
When reminder notifications are enabled on the smart device, pop-ups will occur to help guide the user when
there is a need to change position. Below are examples on the notifications that will pop up on your screen
when it is time to adjust your desk again. The reminders will appear based on your settings. Remember that the
program goes in standby mode if you do not use your computer and therefore it will not remind you until you
start using your computer again.
The notification will tell the user to change position. There are 3 notification options:
- Snooze the reminder: The notification will pop up one hour later.
- Disable reminders for today: The notifications will stop for the day, but they will be enabled again the
next day.
- Open app: Opens the app allowing the user to adjust the desk. (If supported by the connected product)
Page 44 of 28
Recommendations on how to use Desk Control
Overriding a learned sedentary behaviour is a true behavioural challenge. We have put together a guide for how
to break up with your chair during your workday.
How to vary between standing and sitting while your work
The most important thing is to vary your position and to move around, preferably three times an hour. Instead
of sitting for too long at a time, you can switch between standing and sitting position. Remember good posture
and to stand with your body weight evenly distributed on both legs.
• Start by raising your desk and standing for 15 minutes each hour before you go to lunch.
• Raise your desk just before your lunch break. Then your desk will be in the right position when you get back
from lunch.
• Just after lunch, stand for 15 minutes before lowering your desk to sit for 45 minutes.
• Raise your desk again every hour, so that you stand up working for 15 minutes each hour for the rest of the
day.
• Raise your desk before you leave for the day – then it is ready for the next day.
Important reservations when varying between standing and sitting position:
If you are pregnant, have varicose veins or have a health condition that may prevent you from standing for 5-15
minutes at a time every hour, you should contact your doctor to make sure that this will not be detrimental to
your health.
Page 45 of 28
Disposal of LINAK’s products
As LINAK’s customers often ask us how our products can be disposed of or scrapped we have prepared this
guidance that enables a classification to different waste fractions for recycling or combustion.
Guidance
We recommend that our products be disassembled as much as possible and divided into different waste groups
for recycling or combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible material and recoverable
resources.
Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/
aluminium/copper and plastic can be divided into ABS/PA/PE/PP.
As an example, the table below breaks down the different components in LINAK products to various recycling
groups:
Product Components Recycling group
Handset/Control: Plastic housing
Cable
PCB board
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap
By now, almost all our casted plastic parts are supplied with an interior code for plastic type and fibre contents,
if any.
Main groups of disposal
Product main
groups
Metal scrap Cable scrap Electronics
scrap
Plastic recycling
or combustion
Comments
Desk Control App
Bluetooth®
Adapter X X
DPG X X X
Disposal of batteries
"Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK
recommends that used or leaking batteries are disposed through local recycling system. Please do not throw
used or leaking batteries in normal household waste or in nature. This will cause damage to the enviroment.
How to deal with leaking batteries
Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the product, the batteries must be removed at once to minimise damage to
the product.
If leaking batteries are left in the product, it become defective.
It is recommended to use plastic gloves when handling leaking batteries. The contents of a leaking batteries can
cause chemical burns and respiratory irritation.
If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please
seek medical attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and seek
medical attention."
Page 46 of 28
DRAWING APPENDIX
DPG1K
Drawing No.: DPG1K
56
10.510.5
13
29
65.15
9.5
13.5
9.5
R7.35
4.8
21.3 4
1700
2.5
34.4
28.4
Drawing No.: DPG1K
Page 47 of 28
DPG1M
Drawing No.: DPG1M
34.4
421.3
56
R7.35
1700
13.5
9.5
10.5 10.5
29
13
4.8
9.5
28.4
65.15
2.5
Drawing No.: DPG1M
Page 48 of 28
DPG1B/C
Drawing No.: DPG1B-1C
39
3.524.2
69
15
14.5
35.5
13 13
4.8
11
11
14.5
34.5
1700
R10
73.5
Drawing No.: DPG1B-1C
Page 49 of 28
Bluetooth® Adapter
Labels
DPG1K DPG1M DPG1B DPG1C
Bluetooth® Adapter
Page 50 of 28
Page 51 of 28
LINAK APPLICATION POLICY
The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product
defined as hardware, software, technical advice, etc. related to an existing or new customer application.
LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture,
Desk and Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products will be
installed, used, and operated, as each individual application is unique.
The suitability and functionality of the LINAK product and its performance under varying conditions (application,
vibration, load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall ultimately be the
responsibility of the LINAK customer using any LINAK product.
LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it
shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the
application in question.
iPod touch, iPhone, and iPad are trademarks of Apple Inc., regis-
tered in the U.S. and other countries.
“Made for iPod touch”, “Made for iPhone,” and “Made for iPad”
mean that an electronic accessory has been designed to connect
specifically to iPod touch, iPhone, or iPad, respectively, and has
been certified by the developer to meet Apple performance stan-
dards. Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that
the use of this accessory with iPod touch, iPhone or iPad may affect
wireless performance.
The Bluetooth word mark and logos are owned by the Bluetooth
SIG, Inc. and any use of such marks by Ascion, LLC is under license.
Other trademarks and trade names are those of their respective
owners.
Page 52 of 28
Copyright© LINAK 2017.05 . MA-M9-02-680 LINAK A/S reserve the right to make technical alterations
Terms of use
The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing accurate and up-to-
date information on its products.
However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and changes without
prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products.
While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular
product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written
material drawn up by LINAK.
All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK.
FACTORIES
CHINA
LINAK (Shenzhen) Actuator Systems, Ltd.
Phone: +86 755 8610 6656
Fax: +86 755 8610 6990
E-mail: sales@linak.cn . www.linak.cn
DENMARK - Group Headquarters
LINAK A/S, Guderup
Phone: +45 73 15 15 15
Fax: +45 74 45 80 48
Fax: +45 73 15 16 13 (Sales)
E-mail: info@linak.com . www.linak.com
SUBSIDIARIES
AUSTRALIA
LINAK Australia Pty. Ltd
Phone: +61 3 8796 9777
Fax: +61 3 8796 9778
E-mail: sales@linak.com.au . www.linak.com.au
AUSTRIA
LINAK Repräsentanz Österreich (Wien)
Phone: +43 (1) 890 7446
Fax: +43 (1) 890 744615
E-mail: info@linak.de . www.linak.at
BELGIUM & LUXEMBOURG
LINAK Actuator-Systems NV/SA
Phone: +32 (0)9 230 01 09
Fax: +32 (0)9 230 88 80
E-mail: beinfo@linak.be . www.linak.be
BRAZIL
LINAK Do Brasil Comércio De
Atuadores Ltda.
Phone: +55 (11) 2832 – 7070
Fax: +55 (11) 2832 – 7060
E-mail: info@linak.com.br . www.linak.com.br
CANADA
LINAK Canada Inc.
Phone: +1 502 253 5595
Fax: +1 416-255-7720
E-mail: info@linak.ca . www.linak-us.com
CZECH REPUBLIC
LINAK C&S S.R.O.
Phone: +420581741814
Fax: +420581702452
E-mail: info@linak.cz . www.linak.cz
DENMARK - Sales
LINAK Danmark A/S
Phone: +45 86 80 36 11
Fax: +45 86 82 90 51
E-mail: linak@linak-silkeborg.dk . www.linak.dk
SLOVAKIA
LINAK Slovakia s.r.o.
Phone: +421 51 75 63 414
Fax: +421 51 75 63 410
E-mail: jp@linak.sk . www.linak.com
USA
LINAK U.S. Inc.
North and South American Headquarters
Phone: +1 502 253 5595
Fax: +1 502 253 5596
E-mail: info@linak-us.com . www.linak-us.com
FINLAND
LINAK OY
Phone: +358 10 841 8700
E-mail: linak@linak.fi . www.linak.fi
FRANCE
LINAK France E.U.R.L
Phone: +33 (0) 2 41 36 34 34
Fax: +33 (0) 2 41 36 35 00
E-mail: linak@linak.fr . www.linak.fr
GERMANY
LINAK GmbH
Phone: +49 6043 9655 0
Fax: +49 6043 9655 60
E-mail: info@linak.de . www.linak.de
INDIA
LINAK A/S India Liaison Office
Phone: +91 120 4734613
Fax: +91 120 4273708
E-mail: info@linak.in . www.linak.in
IRELAND
LINAK UK Limited - Ireland
Phone: +44 (0)121 544 2211
Fax: +44 (0)121 544 2552
+44 (0)796 855 1606 (UK Mobile)
+35 387 634 6554 (Republic Of
Ireland Mobile)
E-mail: sales@linak.co.uk . www.linak.co.uk
ITALY
LINAK Italia S.r.l.
Phone: +39 02 48 46 33 66
Fax: +39 02 48 46 82 52
E-mail: info@linak.it . www.linak.it
JAPAN
LINAK K.K.
Phone: 81-45-533-0802
Fax: 81-45-533-0803
E-mail: linak@linak.jp . www.linak.jp
MALAYSIA
LINAK Actuators Sdn. Bhd.
Phone: +60 4 210 6500
Fax: +60 4 226 8901
E-mail: info@linak-asia.com . www.linak.my
NETHERLANDS
LINAK Actuator-Systems B.V.
Phone: +31 76 5 42 44 40
Fax: +31 76 5 42 61 10
E-mail: info@linak.nl . www.linak.nl
NEW ZEALAND
LINAK New Zealand Ltd.
Phone: +64 9580 2071
Fax: +64 9580 2072
E-mail: nzsales@linak.com.au
www.linak.com.au
NORWAY
LINAK Norge AS
Phone: +47 32 82 90 90
Fax: +47 32 82 90 98
E-mail: info@linak.no . www.linak.no
POLAND
LINAK Polska
Phone: +48 22 295 09 70
E-mail: info@linak.pl . www.linak.pl
REPUBLIC OF KOREA
LINAK Korea Ltd.
Phone: +82-(0)2-6231-1515
Fax: +82-(0)2-6231-1516
E-mail: info@linak.kr . www.linak.kr
RUSSIAN FEDERATION
000 LINAK
Phone: +7 495 280 14 26
Fax: +7 495 687 14 26
E-mail: info@linak.ru . www.linak.ru
SPAIN
LINAK Actuadores, S.L.u
Phone: +34 93 588 27 77
Fax: +34 93 588 27 85
E-mail: esma@linak.es . www.linak.es
SWEDEN
LINAK Scandinavia AB
Phone: +46 8 732 20 00
Fax: +46 8 732 20 50
E-mail: info@linak.se . www.linak.se
SWITZERLAND
LINAK AG
Phone: +41 43 388 31 88
Fax: +41 43 388 31 87
E-mail: info@linak.ch . www.linak.ch
TAIWAN
LINAK (Shenzhen) Actuator systems Ltd.
Taiwan Representative
Phone: +886 2 27290068
Fax: +886 2 27290096
Mobile: +886 989292100
E-mail: sales@linak.com.tw . www.linak.com.tw
TURKEY
LINAK İth. İhr. San. ve Tic. A.Ş.
Phone: + 90 312 4726338
Fax: + 90 312 4726635
E-mail: info@linak.com.tr . www.linak.com.tr
UNITED KINGDOM
LINAK UK Limited
Phone: +44 (0)121 544 2211
Fax: +44 (0)121 544 2552
E-mail: sales@linak.co.uk . www.linak.co.uk
DISTRIBUTORS
ARGENTINA
Novotec Argentina SRL
Phone: 011-4303-8989/8900
Fax: 011-4032-0184
E-mail: info@novotecargentina.com
www.novotecargentina.com
COLOMBIA
MEM Ltda
Phone: +[57] (1) 334-7666
Fax: +[57] (1) 282-1684
E-mail: servicioalcliente@memltda.com.co
www.mem.net.co
INDIA
Mechatronics Control Equipments
India Pvt Ltd
Phone: +91-44-28558484/85
E-mail: bala@mechatronicscontrol.com
www.mechatronicscontrol.com
INDONESIA
Pt. Himalaya Everest Jaya
Phone: +6 221 544 8956/8965
Fax: +6 221 619 4658/1925
E-mail: hejplastic-div@centrin.net.id
www.hej.co.id
IRAN
Bod Inc.
Phone: +98 2188998635-6
Fax: +98 2188954481
E-mail: info@bod.ir . www.bod.ir
RUSSIAN FEDERATION
000 FAM
Phone: +7 812 3319333
Fax: +7 812 3271454
E-mail: purchase@fam-drive.ru . www.fam-drive.ru
SINGAPORE
Servo Dynamics Pte. Ltd.
Phone: +65 6844 0288
Fax: +65 6844 0070
E-mail: servodynamics@servo.com.sg
www.servo.com.sg
SOUTH AFRICA
Industrial Specialised Applications CC
Phone: +27 11 312 2292 or
+27 11 2077600 (Switch Board)
Fax: +27 11 315 6999
E-mail: gartht@isagroup.co.za
www.isaza.co.za
UNITED ARAB EMIRATES
Mechatronics
Phone: +971 4 267 4311
Fax: +971 4 267 4312
E-mail: mechtron@emirates.net.ae
For contact details on other countries
please visit www.linak.com or contact:
LINAK INTERNATIONAL
Phone: +45 73 15 15 15
Fax: +45 74 45 90 10
Fax: +45 73 15 16 13 (Sales)
E-mail: info@linak.com . www.linak.com