LINKSYS CG7500 D3 WiFi Gateway User Manual

LINKSYS LLC D3 WiFi Gateway

UserManual.wiki >

LINKSYS >

CG7500 User Manual HTML Version

User Manual

USER GUIDE

AC1900 | 24x8

CABLE MODEM ROUTER

Model CG7500

Contents

Product Overview ......................................................................................... 3

Front view ..................................................................................................................................... 3

Back ................................................................................................................................................ 5

Installation ...................................................................................................... 6

Setup .............................................................................................................................................. 6

Setup Wizard ............................................................................................................................... 8

Browser-Based Utility .............................................................................. 12

How to access the browser-based utility ....................................................................... 12

How to use the browser-based utility .............................................................................. 13

System Status ............................................................................................ 14

Status ......................................................................................................................................... 14

Configuration .............................................................................................. 16

Connectivity ............................................................................................................................. 16

Wi-Fi ............................................................................................................................................. 19

External Storage ..................................................................................................................... 23

Security ...................................................................................................................................... 26

Administration ......................................................................................................................... 29

Parental Controls ...................................................................................... 33

Troubleshooting ......................................................................................... 34

Specifications ............................................................................................. 37

Linksys GG7500 ..................................................................................................................... 37

Environmental .......................................................................................................................... 37

Product Overview

Front view

From top to bottom

Power------Lights up green when the modem router is powered on.

Receive— Light blinks green while the modem router is searching for a connection over

the cable network. Light is solid green when the modem router is receiving data from the

cable network. Light is solid blue during multichannel bonding.

Send------Light blinks green while the modem router is searching for a connection over the

cable network. Light is solid green when the modem router is sending data to the cable

network. Light is solid blue during multichannel bonding.

Status— Lights up green when the modem router has an Internet connection. Flashes

green while the modem router is establishing the Internet connection.

Ethernet------Light is solid green when the modem router is connected to a device through

the LAN port.

2.4 GHz Wi-Fi—Light is solid green when broadcasting 2.4 GHz signal. Light blinks when

the modem router is actively sending or receiving data over the network.

5 GHz Wi-Fi—Light is solid green when broadcasting 5 GHz signal. Light blinks when the

modem router is actively sending or receiving data over the network.

USB------ Light is solid green when the modem router is connected to a device through the

USB port.

WPS------Light is solid green when a Wi-Fi Protected Setup™ connection is successfully

established. Light blinks slowly while WPS is setting up a connection, and blinks rapidly if

an error occurs. Light is off when WPS is idle.

Back

From top to bottom

USB port------Connect and share a USB drive on your network or on the internet.

Reset button------Press and hold for about five seconds to reset the modem router to

factory defaults.

Ethernet ports— Connect the modem router to computers and other devices with

ethernet cables (also called network cables).

Cable port------ Connect the modem router to an active cable signal with a coaxial cable.

Power port------Connect to the included power adapter.

Installation

Setup

Disconnect any modems or modem routers before setting up your new modem router.

1. Connect a coaxial cable to the cable port on the modem router and a wall jack.

2. Connect the power adapter to the modem router and plug into a power source.

3. Connect to the secure Wi-Fi name on the sticker in the Quick Start Guide that

came with your modem router. There is also a sticker on the bottom of the modem

router. (You can change these details later.) Select the option to automatically

connect to this network in the future. You will not have internet access until you

complete modem router setup.

4. Open a web browser and type http://192.168.1.1 in the address bar.

5. In the pop-up window, enter “admin” in the Password field. Click Log in. The web-

based setup page of your modem router will appear.

6. Make sure you are on the

Quick Start

tab. Click Begin to start the setup wizard.

Setup Wizard

Accept the License Terms and click Next.

Choose an internet service provider, activate your modem router and click Next.

Create a Wi-Fi name and password and click Next.

Create an admin password and click Next.

Write down your settings somewhere you’ll remember and click Save.

Click Done and get online.

When your modem router is ready, the top four lights (power, receive,

send, status) will be solid.

Advanced users can select “I want to skip the Setup and configure the router

manually.”

If you choose to manually set up the modem router, you will need to have the

following information available for activation:

• Account number of your broadband subscription

• Phone number linked with your account

• Serial number of the modem router (on the back of the unit)

• MAC address of the modem router (on the back of the unit)

To activate:

Open a web browser from a computer that’s connected directly to the modem

router. This is where you will need the information above (account number of your

broadband service, phone number and new modem router device identifiers).

Some service providers have additional setup steps that will automatically appear

in the browser – if not, visit the appropriate link below. Follow the steps for your

internet provider or call them if you are unable to get online.

Note—The modem router may reboot several times during this process and

activation can take up to five minutes.

After activation, you should be able to connect to the internet wirelessly via your

modem router or a wired connection between your computer and the modem

router.

Helpful links:

• https://install.charter.com/

• https://activation.cox.net

• www.xfinity.com/activate

Browser-Based Utility

If you would like to change the modem router’s advanced settings, use the browser-based

utility. For more help with the utility, click the Help link in the upper-right corner of the

screen or go to our support website www.linksys.com/support/cg7500.

How to access the browser-based utility

1. Launch the web browser on your computer, and enter the router’s default Internet

Protocol (IP) address, 192.168.1.1, in the address field. Press Enter.

2. In the Password field, enter the password created during setup. If you did not

change the password, the default is ‘‘admin’’.

3. Click Log in to continue.

How to use the browser-based utility

Navigate the utility by using the tabs along the top of the screen and the corresponding

specific menus down the left side of the screen.

If you change any settings on a screen, you must click the Save button at the bottom of

the screen to apply your changes. Likewise, click Cancel to clear your changes.

Note—To learn more about any field, click the Help link in the upper-right corner of the

screen.

System Status

Status

Status > Overview

Overview tells you how long the router has been working since its last restart (Router

Uptime), and how long it has been connected to the internet (Internet Uptime) in that

period. This screen also shows your Wi-Fi name and password, and some details on any Wi-

Fi devices managed by Parental Controls.

Status > System Information

System Information page shows basic information such as the MAC address, software

version, and the time that has elapsed since the last restart etc.

Status > Wi-Fi

The Wi-Fi screen provides detail about all Wi-Fi bands, including Guest Wi-Fi. Clicking the

Wireless Clients button displays details about any connected Wi-Fi devices.

Configuration

Connectivity

Connectivity > Local Network

Your router ships with the most common settings, and several settings are configured

during setup. You may never have to change these settings.

LAN IP Address

The router's IP address on your Wi-Fi. If you change this address, you’ll have to reconnect

your devices to your router.

Subnet Mask

The router’s subnet mask on your Wi-Fi. It is used to divide a network into subnets so

information can be routed correctly to computers and devices.

DHCP Server

DHCP (Dynamic Host Configuration Protocol) is enabled by default. DHCP assigns IP

addresses as needed to devices connected to your Wi-Fi.

DHCP Starting Address

The value that the DHCP server starts with when issuing IP addresses.

DHCP Ending Address

The value that the DHCP server ends with when issuing IP addresses.

DHCP Lease Time

The amount of time a Wi-Fi user is allowed connection to the router with her current IP

address. When the time has expired, the user will be automatically assigned a new IP

address, or the lease will be renewed.

Static DNS 1-3

Domain Name System (DNS) is how the internet translates a domain or website name into

an internet address, or URL, that you can access. Your ISP will provide at least one DNS

server IP address. You can enter up to three.

WINS

Windows Internet Naming Services manages each computer’s interaction with the

internet. If you use WINS a server, enter the server’s IP address. Otherwise, leave it blank.

DHCP Reservations

Click to add or change the DHCP reservations used on your Wi-Fi. DHCP reservations

allow you to assign a unique, fixed IP address to a specific device on your Wi-Fi. This is

helpful when managing devices such as print servers, cameras, printers or game consoles.

A fixed IP address is also recommended if you want to use port forwarding for devices

that need to receive inbound date from the internet. To assign an IP address and MAC

address to a device, click Add and then enter the device name, IP address, and MAC

address. When finished, click Apply.

Connectivity > WAN Setup

WAN Information

Select your internet connection type. If you don’t know, call your ISP.

Automatic Configuration – DHCP—Select if your ISP assigns IP addresses dynamically,

meaning you get different IP addresses each time you start your computer.

Static IP------Select this if you use the same IP address each time you connect to the

internet. Enter your internet address, subnet mask, default gateway, and DNS entries. You

can get this information from your ISP.

Domain Name Server Address

Most users get a Domain Name Server address automatically from their ISP. If you

subscribe to your own DNS server, select Use These DNS Servers and complete the

field(s).

Option

This section is for advanced users.

Connectivity > Advanced Routing

Click Add to assign a specific IP address, subnet mask, and gateway address to a specific

device. Click Apply.

Connectivity > Connected Devices

Information about devices connected to your Wi-Fi.

Wi-Fi

Wi-Fi > Wi-Fi Settings

Wi-Fi Name

Personalize the Wi-Fi name that appears in the list of available networks.

Broadcast Wi-Fi Name

Allows Wi-Fi devices to detect your Wi-Fi name when they survey the local area for

available Wi-Fi. Not broadcasting your Wi-Fi name does not improve your Wi-Fi security.

Network Mode

Select the standard your Wi-Fi supports.

Bandwidth

The Auto setting provides the best performance with Wireless-B, Wireless G, and Wireless

N (2.4 GHz), Wireless-A, Wireless-N, Wireless-AC (5 GHz) devices. For a channel width of

20 MHz, select 20 MHz only.

Channel

Select the channel for Wireless-B, Wireless-G, Wireless-N, Wireless-A, or Wireless-AC

networking. If you’re not sure which one to use, choose Auto.

Security Mode

Each device on your Wi-Fi must use the same security mode.

Password

Wi-Fi devices must enter this password, sometimes called a security key, to connect to

your Wi-Fi.

Wi-Fi > MAC Filtering

MAC filtering is a way to allow or deny access to your network by identifying specific MAC

addresses. It is not a good substitute for a secure Wi-Fi password. If you enable MAC

Filtering, Wi-Fi Protected Setup will be disabled automatically.

MAC Filters

Select Enabled to begin filtering Wi-Fi devices by MAC address.

Filter Options

Allow Access List limits access to devices whose MAC addresses are listed. All other

devices will be denied. Deny Access List allows you to create a list of MAC addresses that

cannot access your network. All devices not on that list will be able to connect to your

network.

Add MAC Address

Add a MAC address to your list.

Wi-Fi > Wi-Fi Protected Setup

Wi-Fi Protected Setup makes it easy to add devices to your Wi-Fi without having to enter a

Wi-Fi name and password. To use Wi-Fi Protected Setup, the device you want to connect

must support it.

WPS Enabled

If you uncheck this box, you can't use Wi-Fi Protected Setup to connect devices to your

Wi-Fi, and the Wi-Fi Protected Setup push button on your router will also be disabled.

Push Button

Use this if your device has a Wi-Fi Protected Setup button or prompts you to press the Wi-

Fi Protected Setup button on your router. Press or click the Wi-Fi Protected Setup button

on the device you want to connect to Wi-Fi, and then click the button on this page.

Router PIN

Use this if the device you're connecting asks for the router PIN (Personal Identification

Number). The router PIN is also listed on the bottom of the modem router.

Device PIN

Use this if your device has a Wi-Fi Protected Setup PIN. Enter the PIN from the device into

the PIN field and then click Register.

Wi-Fi > Guest Access

Guest Access is a way to share internet access. Guests can get online, but they can’t see

or access other connected devices. You can turn guest access on and off, give it a name

and password, and set the number of guest devices allowed.

When you set up your router, a secure guest network was created automatically on the

router's 2.4 GHz/5 GHz band. Guest access is available on these two bands. Be sure to

keep this in mind if you're connecting other networking devices, such as an extender. It

should be configured to use the 2.4 GHz/5 GHz band as well if you plan to use guest

access.

Wi-Fi > Advanced Settings

IGMP Snooping is turned on by default. Only advanced users should turn off this setting.

External Storage

External Storage > Status

Click Eject before physically disconnecting a USB disk from the modem router. This

prevents the possible loss of data, which may occur if you remove the disk while it is

transferring data.

External Storage > Folder Access

You can decide who has access to external storage connected by USB to your modem

router. When Shared Status is disabled, anyone on your network can access all content on

your storage device. If it is enabled, you can specify which users can see which content.

Click Eject before physically disconnecting a USB disk from the modem router. This

prevents the possible loss of data, which may occur if you remove the disk while it is

transferring data.

External Storage > FTP Server

You can access the folders on your storage device remotely from anywhere you have an

internet connection using an FTP (File Transfer Protocol) server. You can access the

content using a web browser or FTP software.

Server Name - -- Personalized the name of your FTP server.

FTP Server

Select to enable the FTP server, and make content available remotely.

Internet Access

Select to allow access to your storage device with a web browser.

FTP Port

The default port, 21, will work for most users. Advanced users may change to a different

port to serve their needs.

Add FTP Folder

To add a FTP folder, enter the server name and the information to use.

External Storage > Media Server

A media server lets you share across your network content on an attached external

storage device. You can share media with devices that are UPnP AV (Audio and Video)-

enabled or DLNA (Digital Living Network Alliance)-certified devices in your home. These

include digital media players, gaming consoles with a built-in media player, and digital

picture frames.

You can specify which folders are used by the media server, add and disabled/delete

folders, and specify how often the folders are scanned for new content.

Media Server

Select to share media.

Server Name

Personalize the display name of your UPnP media server.

Scan Interval

Specify how often the modem router scans folders on the external storage device for new

content. Scanning can take several hours, especially the first time the device is scanned,

or if you add a lot of new content. Subsequent scans should take less time. To scan the

folders immediately, click Scan Now.

Click Add New Folder to add a new shared media folder. Select the folder on the attached

external storage device that contains the content you want to share.

External Storage > Account

Two user accounts are preset for the modem router: admin and guest. The password for

the admin user is the modem router’s admin password. The password for the guest user is

"guest".

Group Management

If you want to add to the default groups, click Create New Group and enter the name,

description and the type of permission the group will have. Select

Read and Write

to allow

the group to view, edit, or delete content. Select

Read Only

to limit the group to viewing

content.

User Management

If you want to add a user to one of your groups, click Create New User and enter a user

name, description, and password, and assign the user to a group.

Security

Security > Firewall

The firewall, which protects your Wi-Fi from internet threats, is enabled by default.

Security > DMZ

The Demilitarized Zone (DMZ) feature can be used to expose a web server, mail server, or

web camera to the internet so anyone can access it. This feature is not recommended

because it presents significant security risks to the device that you designate for the

DMZ. The device will not be protected by the built-in firewalls, internet filters, or modem

router web filters.

With DMZ enabled, use the

Destination IP Address

to identify the device you wish to be in

the DMZ. Click View DHCP Client Table to see a list of connected devices. Select the IP

address of the desired device and it will automatically populate the

Destination IP Address

field.

Security > DDNS

The DDNS feature lets you configure a domain name for your home network, which you

can use to easily find your network on the internet. This is useful if you want to remotely

access a USB drive or web camera over the internet.

Select your DDNS service and complete the fields with information provided to you by

your DDNS provider.

Security > Single Port Forwarding

Single Port Forwarding directs inbound traffic from the internet on a specific port to a

single device on your Wi-Fi. For example, forwarding inbound web requests, typically on

port 80, to a web server. To forward to multiple ports, create additional entries to forward

additional ports to the same IP address. Click Add a New Single Port Forwarding.

Application name

The application or device name using port forwarding. Refer to your device's

documentation for recommendations if needed.

External Port

Enter the external port number.

Internal Port

Enter the internal port number.

Protocol

Select the protocol to use.

Device IP Address

Enter the IP address you have reserved for the computer you want to forward internet

traffic to.

Status

Select to use the port forwarding. If you don't want to use port forwarding but want to

keep the information in the table, unselect the checkbox.

Security > Port Range Forwarding

Port forwarding directs inbound traffic from the internet on range of ports to a specific

device on your Wi-Fi. For example, some applications can use a range of ports so that if

one port is busy, they can try another one. Click Add a New Port Range Forwarding.

Application name

The application or device name using port forwarding.

Start-End Port

The port number or range of ports used by the application or device for port forwarding.

To specify a range of ports, separate the first and last port numbers with a dash, for

example, 5800-5900.

Protocol

Select the protocol to use, typically TCP.

Device IP Address

Enter the last three digits of the IP address of the computer running the software that

requires port forwarding.

Status

Select to use port range forwarding. If you don't want to use port forwarding but want to

keep the information in the table, unselect the checkbox.

Security > Port Range Triggering

Port range triggering allows the modem router to watch outgoing data for specific port

numbers. The cable modem remembers the IP address of the device that sends the data

so returning data is routed back to the proper device. This is useful when using a USB or

Bluetooth headset for online chat and gaming. Click Add a New Port Range Triggering.

Application name

The application or device using port triggering.

Trigger Port Range/Forward Port Range

The port number or range of ports used by the application or device for port triggering.

Status

Select to use port range triggering. If you don't want to use port range triggering for that

entry, but want to keep the information in the table, unselect the checkbox.

Administration

Administration > Password

Allows you to change the modem router password. Use it to access modem router settings

and features such as Guest Access and Parental Controls. To change the password, first

enter the old password, then type a new password and confirm it. Click Save. Be sure to

write down this password and keep it somewhere safe.

Administration > Time Zone

Set the current time zone for your area and adjust the time for daylight savings time

changes.

Administration > Remote Management

Select a remote access protocol and identify a port to use when accessing your modem

router settings when away from home and not connected to your Wi-Fi.

Protocol

Select the protocol for remote access.

On/Off

Enabled/Disabled the remote access.

Port

Enter the port number that will be open to remote access.

Allow Any Host to Access the Device Remotely

Select to allow remote access to the modem router from any external IP address. Deselect

to specify an external IP address or range of IP addresses allowed to remotely access

your modem router.

Administration > Gateway Function

UPnP (Universal Plug and Play) allows devices connected to Wi-Fi to discover each other

and automatically create working configurations. Examples of UPnP-capable devices

include web cameras, online gaming applications, and VoIP devices. UPnP is enabled by

default.

Select to allow users to change router settings or disable your local internet connection

while using UPnP.

SIP ALG (Session Initiation Protocol Application Layer Gateway) is a feature that allows

certain VOIP service providers to get through your modem router's firewall. Select to use

this feature.

Administration > Backup

Backup Your Configurations

Back up your modem router’s settings to a file on your computer. You can use the file later

if you need to restore the settings. To create a backup file of the current settings.

Restore Your Configurations

Click Choose File and navigate to the backup file you want to restore. Click Restore.

Administration > Device Reset

Restart the Modem Router

Restarts your modem router by turning it off and then on again. All devices connected to

your modem router will be disconnected. They will reconnect automatically when the

restart finishes.

Reset to Factory Default Settings

Resets all modem router settings to how they were before you set it up. A reset changes

the modem router name, password, security settings, parental control settings, and all

other settings you have changed. After a reset, you can customize your settings again.

Parental Controls

Use Parental Controls to manage internet use by blocking access per device. You also can

block specific sites per device. Once you turn on Parental Controls, click Block Internet

Access next to a device in the C

onnected Devices

table. Select

Never, Always

Specific

Times

. If you choose

Specific Times

, you will have to select the days and times you want to

block the internet on that device.

Click

Add

next to

Block Specific Sites

and Choose Block Sites and enter the URL of the

sites you want to block from that device. Click Apply. Click

Add

again to block another

site.

Use the

Manage Device Table

to change parental control settings. Click Manage to make

changes and Delete to undo all parental controls on a device.

Click Add a New Device to assign parental controls to a new device on your Wi-Fi. Enter a

device name and the device’s MAC address, then choose when to block the internet to

that device.

Click Save before leaving the page.

Troubleshooting

DOCSIS Provisioning

This screen provides details on the provisioning of your modem router.

Diagnostics

Use diagnostics to aid in troubleshooting your modem router's connectivity.

Ping

Check whether a destination IP/URL is available.

Traceroute

Trace the routing path to the destination IP/URL.

Abort

Stop ping test or traceroute test.

DOCSIS WAN

The DOCSIS WAN screen shows a DOCSIS overview, and downstream/upstream activity

overview. Click Reset FEC Counters to start counting new errors

(Correcteds/Uncorrectables).

DOCSIS Event

The DOCSIS event log chronicles DOCSIS errors that generated log entries.

Report

The report shows details about your router and its current network settings. This

information can be very helpful if you have to call your ISP or Linksys Support for help with

your Internet connection or router.

The following buttons are available for both the Devices and Report pages:

Refresh

Redisplays the most current information.

Prints the information currently displayed.

Specifications

Linksys CG7500

Model Name

AC1900 | 24x8 Cable Modem Router

Model Number CG7500

Switch Port Speed 10/100/1000 Mbps (Gigabit Ethernet)

Radio Frequency

2.4 GHz and 5 GHz

# of Antennas 6 internal

Ports

Cable, Power, USB 2.0, Ethernet (1-4)

Buttons

Reset

Lights Ethernet, WPS, Wi-Fi, Internet

(Send/Receive/Status), Power, Ethernet

UPnP

Supported

Security Features

WEP, WPA-Enterprise, WPA2-Personal

Security Key Bits

Up to 128-bit encryption

Storage File System Support

FAT, NTFS, and HFS+

Environmental

Dimensions

30 mm x 185mm x 240 mm

Unit Weight .924 kg (2.04 pounds)

Power

12V, 3A

Certifications FCC, UL, Wi-Fi (IEEE 802 .11ac/a/b/g/n), RoHS

Operating Temperature 0 to 40°C (32 to 104°F)

Storage Temperature

-20 to 60°C, (-4 to 140°F)

Operating Humidity

10% to 80% relative humidity, non-condensing

Storage Humidity

5% to 90% non-condensing

Specifications are subject to change without notice.

NOTES

For regulatory, warranty, and safety information, see the CD that came with your modem

router or go to Linksys.com/support.

Maximum performance derived from IEEE Standard 802 .11 specifications. Actual

performance can vary, including lower wireless network capacity, data throughput rate,

range and coverage. Performance depends on many factors, conditions and variables,

including distance from the access point, volume of network traffic, building materials and

construction, operating system used, mix of wireless products used, interference and

other adverse conditions.

Visit linksys.com/support/ for award-winning technical support.

BELKIN, LINKSYS and many product names and logos are trademarks of the Belkin group

of companies. Third-party trademarks mentioned are the property of their respective

owners.

LNKPG-00350 Rev. A00

FCC Statement

This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: ( ) This device may

not cause harmful interference, and (2) this device must accept any interference received, including interference that may

cause undesired operation.

This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 5 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and devices.

• Connect the equipment to an outlet other than the receiver’s.

• Consult a dealer or an experienced radio/TV technician for assistance.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate this equipment.

Mexico Regulatory Statement

La operación de este equipo está sujeta a las siguientes dos condiciones: ( ) es posible que este equipo o dispositivo no

cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda

causar su operación no deseada.

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment

should be installed and operated with minimum distance 32 cm between the radiator and your body.

This device and it’s antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter

except in accordance with FCC multi-transmitter product procedures.

Wireless Disclaimer

The maximum performance for wireless is derived from IEEE Standard 802. specifications. Actual performance can

vary, including lower wireless network capacity, data throughput rate, range and coverage. Performance depends on many

factors, conditions and variables, including distance from the access point, volume of network traffic, building materials and

construction, operating system used, mix of wireless products used, interference and other adverse conditions.

For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not

possible. This device is restricted for indoor use.

Restrictions in the 5 GHz Band

The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-

channel mobile satellite systems.

UL statement

Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70,the National Electrical Code

(NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.

Safety Notices

WARNING: Do not use this product near water, for example, in a wet basement or near a swimming pool.

WARNING: Avoid using this product during an electrical storm. There may be a remote risk of electric shock

from lightning.

WARNING: The power adaptor is the equipment´s disconnection device. The power outlet must be located nearby

the equipment and its access must be easy.

WARRANTY AND SUPPORT INFORMATION

IMPORTANT!

PLEASE RETAIN PROOF OF PURCHASE AND PRODUCT WARRANTY INFORMATION

END USER LICENSE AGREEMENT

Belkin International, Inc., including all affiliates and subsidiaries (“Belkin”, “us” or “we”) thanks you for choosing one of our

Belkin, Linksys or WeMo products (the “Product”). This End-User License Agreement (this “Agreement”) is a legal document

that contains the terms and conditions under which limited use of certain Software (as defined below) that operates with

the Product is licensed to you.

PLEASE READ THIS AGREEMENT CAREFULLY BEFORE INSTALLING OR USING THIS PRODUCT.

BY CHECKING THE BOX OR CLICKING THE BUTTON TO CONFIRM YOUR ACCEPTANCE WHEN YOU FIRST INSTALL

THE SOFTWARE, YOU ARE AGREEING TO ALL THE TERMS OF THIS AGREEMENT. ALSO, BY USING, COPYING OR

INSTALLING THE SOFTWARE, YOU ARE AGREEING TO ALL THE TERMS OF THIS AGREEMENT. IF YOU DO NOT

AGREE TO ALL OF THESE TERMS, DO NOT CHECK THE BOX OR CLICK THE BUTTON AND/OR DO NOT USE, COPY

OR INSTALL THE SOFTWARE, AND UNINSTALL THE SOFTWARE FROM ALL DEVICES THAT YOU OWN OR CONTROL.

IF YOU DO NOT ACCEPT THE TERMS OF THIS AGREEMENT AND YOU PURCHASED A PRODUCT CONTAINING

THE SOFTWARE FROM AN AUTHORIZED RETAILER, RESELLER OR APP STORE (AS DEFINED BELOW), YOU MAY

BE ELIGIBLE TO RETURN THE PRODUCT FOR A REFUND, SUBJECT TO THE TERMS AND CONDITIONS OF THE

APPLICABLE RETURN POLICY.

This product is Software licensed to you by Belkin and, where applicable, by Belkin’s suppliers. “Software” means any and all

firmware programs and associated files provided with respect to the Product; any and all software programs, applications

or “apps” and associated files provided with respect to the Product; all modified versions of and upgrades or improvements

to such programs (such as those provided via web-based updates), all subsequent versions of such programs, and all copies

of such programs and files. Software does not include any Open Source Software (as defined below).

By “you,” we mean the purchaser, recipient or other end user of the Product containing the Software or the purchaser,

recipient or other end user of the Software on a standalone basis. “You” may also mean a person who has downloaded the

Software from an authorized website, such as http://www.belkin.com or from an authorized application market or store,

such as Apple’s App Store or Google Play (each such application market or store is referred to in this Agreement as an “App

Store” and collectively as “App Stores”).

. LICENSE GRANT. Belkin hereby grants you the right to use: (i) where your Product is not a “Small-Medium Business

or SMB” branded Product, for your personal, non-commercial purposes; or (ii) where your Product is a “Small Medium

Business or SMB Product, for your personal or commercial use; copies of the Software in object code form on

devices that you own (or, in the case of firmware, one copy of the firmware in object code form solely on the Product

relating to the firmware). As part of this license, you may (A) operate the Software in the manner described in the user

documentation for the Software; (B) where the Software is provided for download onto a personal computer or mobile

device, make as many copies of the Software as you reasonably need for your own use (this does not include firmware);

and (C) permanently transfer all of your rights to use the Product (including but not limited to the Software) to another

person, so long as that person also agrees to be bound by this Agreement, and following such transfer you stop using

the Product and the Software.

You can find the user documentation for the Software on the “Support” page of the applicable Belkin website.

2. LICENSE RESTRICTIONS. The Software is licensed, not sold, to you. You only have the non-exclusive right to use

the Software in accordance with this Agreement. You may not (i) modify, adapt or otherwise create derivative works

from the Software, the Product containing the Software or user documentation (except as may be permitted by an

applicable open source license) without receiving prior written consent from Belkin to make any such modifications: (ii)

lease, sublicense, resell, rent, loan, redistribute, or otherwise transfer (except as expressly permitted above), whether

for commercial purposes or otherwise, the Software or user documentation; (iii) reverse engineer, disassemble, decrypt

or decompile the Product or the Software or otherwise try to reduce the Software to a human-readable form, except

where and only to the extent that such activity is permitted by applicable law or where Belkin is required to permit

such activity under the terms of an applicable open source license; (iv) remove or alter any copyright, trademark or

other proprietary notices contained in the Software or user documentation; (v) use the Product, Software or user

documentation to develop a competing hardware and/or software product, or otherwise in any manner not set forth

in this Agreement or the user documentation; (vi) if the Software is firmware, copy the firmware (other than one

backup copy for archival purposes only), use it on a multi-user system or operate it separately from the Product onto

which it is embedded; (vii) use the Software to transmit software viruses or other harmful computer code, files or

programs, or to circumvent, disable or otherwise interfere with security-related features of the Software; (viii) use the

Software to collect or harvest any third party’s personally identifiable information, to send unauthorized commercial

communications or to invade the privacy rights of any third party; or (ix) use the Software for any unlawful purpose, and/

or in any manner that breaches this Agreement. All rights not expressly granted to you by Belkin under this Agreement

are hereby reserved by Belkin. You will not acquire such rights, whether through estoppel, implication, or otherwise.

3. APP SOFTWARE RESTRICTIONS. If you have downloaded the Software from an App Store, you are also subject to any

do under this Agreement, or permit you to do some of the things you are prohibited from doing under this Agreement. In

addition, application of the App Store’s terms of use may result in other terms of this Agreement not being applicable to

the Software or applying in a different way than this Agreement states. If your use of the Software is subject to an App

Store’s terms of use, then in the event of any conflict or ambiguity between the terms of this Agreement and such App

Store’s terms of use, the App Store’s terms of use will govern, but only to the extent necessary to resolve such conflict

or ambiguity, and the terms of this Agreement will otherwise remain in full force and effect. Notwithstanding anything

to the contrary in this Agreement, by using the Software, you acknowledge and agree that it is solely your responsibility

to understand the terms of this Agreement, as well as the terms of use of any App Store that may be relevant to the

LIMITED WARRANTY

(UNITED STATES AND CANADA)

This warranty is provided to you by Belkin International, Inc, or one of its subsidiaries or affiliates (“Belkin”)

IMPORTANT NOTICE REGARDING YOUR CONSUMER RIGHTS

The benefits we give in this manufacturer's warranty are additional to any rights and remedies that you may have under

local consumer protection laws. Nothing in this warranty limits or affects your legal rights.

This manufacturer's warranty is governed by the laws of the country in which you purchased your Belkin, Linksys or WeMo

product. In many countries, consumers have rights under local consumer laws. Those consumer rights may differ between

countries, states and provinces, and often cannot be excluded. Your local consumer rights organization can advise you on

your legal rights.

This manufacturer's warranty is not intended to:

• change or exclude any rights under consumer law that cannot be lawfully changed or excluded; or

limit or exclude any right you have against the person who sold the Belkin, Linksys or WeMo product to you if that person

has breached their sales contract with you.

WHAT DOES THIS WARRANTY COVER?

Belkin warrants that the product hardware and any software media (i.e., media on which the product software is provided)

will be free from defects in materials and workmanship under normal use during the Warranty Period described below. This

means that the product won’t be defective, and that it will look and work as advertised during the relevant period.

This warranty does not apply to products purchased from a source other than Belkin or a Belkin Authorized Reseller.

How long is the product warranted?

Belkin warrants that the hardware in this Belkin, Linksys or WeMo product, and any associated software media, will be free

from defects in materials and workmanship under normal use during the Warranty Period. The Warranty Period begins on

the date the product was purchased by the original end-user purchaser and lasts for the period set out in the table below:

Product Type Warranty Period

New products2 months

Refurbished products 90 days

Repaired or replacement products The longer of the original Warranty Period or 30 days

Software media (if provided with the product)90 days

A claim under this warranty is only eligible if it is made within the Warranty Period.

What isn’t covered?

Belkin does not give any warranty:

• in relation to software or services, provided by Belkin or any third party, included in or with the product;

• that the product, software or services will always operate uninterrupted or error free;

• that the product, software or services, or any equipment, system or network on which the product, software or

services are used are 00% secure and cannot be hacked; or

• that a third party service the product needs will always be available.

Note: Although Belkin does not make these promises in this warranty, you may have additional rights under consumer laws.

Will this warranty always apply?

This warranty does not apply if:

• the product has been tampered with or the assembly seal has been removed or damaged;

• the product has been altered or modified by someone other than Belkin;

• the warranty claim was made fraudulently or by misrepresentation;

• the product was not installed, operated, repaired, or maintained in accordance with Belkin’s instructions;

• the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident;

• damage to the product is cosmetic, including scratches and dents, or defects caused by normal wear and tear or

normal aging of the product;

Software or the Product.

4. UPGRADES AND UPDATES. While Belkin is not required to do so, Belkin may provide you with upgrades or updates

to this Software. This Agreement will govern any upgrades provided by Belkin that replace and/or supplement the

original firmware and/or Software, unless such upgrade is accompanied by a separate end user license agreement, in

which case the terms of that end user license agreement will govern. If you decide not to download and use an upgrade

or update provided by Belkin, you understand that you could put the Software at risk to serious security threats or

cause the Software to become unusable or unstable. Some Products include an auto-update feature, which gives us

the ability to make updates automatically. You can change auto-update options by changing your settings within the

Product account information. In very limited cases, updates may still be automatically applied, regardless of the auto-

update setting. For example, we may provide an automatic update that fixes a security breach or vulnerability to your

network. We may also provide you with updated Software data files automatically to benefit you, such as to provide you

with updated device information to identify new devices in your network. These data files do not update your firmware,

but consist of Software files that are cached on your Product and override older files. By agreeing to this Agreement,

you agree to automatic updates.

5. DATA AND PRIVACY. We at Belkin are committed to protecting your privacy. Our goal is to provide you with a positive

experience when using our apps, products and services, while at the same time keeping your Personal Information,

as defined in the Belkin Privacy Policy (the “Privacy Policy”), secure. Our privacy practices are described in the Privacy

Policy, as well as in separate notices given when an app, product or service is purchased or downloaded. By using

Belkin Products or providing us with your Personal Information, you are accepting and consenting to the practices,

terms and conditions described in the Privacy Policy. At all times your information will be treated in accordance with the

Belkin Privacy Policy, which is incorporated by reference into this Agreement and can be viewed here.

6. OPEN SOURCE SOFTWARE. You hereby acknowledge that the Software may contain Open Source Software (as

defined below). This license does not apply to Open Source Software contained in the Software. Rather, the terms

and conditions in the applicable Open Source Software license shall apply to the Open Source Software. Nothing in

this Agreement limits your rights under, or grants you rights that supersede, any Open Source Software license. You

acknowledge that the Open Source Software license is solely between you and the applicable licensor of the Open

Source Software. You shall comply with the terms of all applicable Open Source Software licenses, if any. License and

tab on Belkin websites and within the “Contact Us” section on Linksys websites. Belkin is not obligated to provide

any maintenance or support for the Open Source Software or any Product Software that has been modified by you

pursuant to an Open Source Software license.

“Open Source Software” means any software or software component or technology that is subject to an open source

license. Open source licenses are generally licenses that make source code available for free modification and distribution,

but can also apply to technology received and distributed solely in object code form. Examples of open source licenses

include: (a) GNU's General Public License (GPL) or Lesser/Library GPL (LGPL); (b) the OpenSSL License; (c) the Mozilla

Public License; (d) the Berkeley Software Distribution (BSD) License; and (e) the Apache License.

7. INTELLECTUAL PROPERTY RIGHTS. All title and intellectual property rights (including without limitation all

copyrights, patents, trade secret rights and trademark rights) in and to the Software (including but not limited to any

content incorporated into the Software), the accompanying printed materials, and any copies of the Software, are

owned by Belkin or its suppliers. Therefore, you must treat the Software like any other material protected by laws and

treaties relating to international property rights and in accordance with this Agreement.

8. THIRD PARTY PRODUCTS AND SERVICES. The Software may contain links or other features that make it easier

for you to visit or log-in to independent third-party websites (“Linked Sites”). These features are provided solely as a

convenience to you. Linked Sites are not under Belkin’s control, and Belkin is not responsible or liable for and does

not endorse the content or practices of such Linked Sites, including any information or materials contained on such

Linked Sites. You will need to make your own independent judgment regarding your interaction with these Linked Sites.

You hereby waive and release any legal claim you might have against Belkin with respect to these sites or third-party

products or services, and your use of these sites, third-party products or services. We encourage you to read the terms

and conditions and privacy policy of each third party website that you choose to visit.

9. INDEMNITY. If Belkin is the subject of a claim, becomes involved in a legal proceeding, or suffers any economic loss

or damage as a result of your violation of this Agreement, to the extent permitted by law, you will be responsible for

compensating Belkin for the full amount of its loss, as well as any reasonable amounts Belkin incurs in lawyers' fees,

expenses and court costs, except to the extent that Belkin contributed to the loss or damage.

0. TERM. This Agreement is effective when you click on the “I Accept” button, or when you in any other way use, copy or

install the Software, which will constitute your acceptance of, and agreement to, this Agreement. Once accepted, this

Agreement remains in effect until terminated. The limited license in this Agreement will be automatically terminated

if you fail to comply with any of the terms and conditions in this Agreement. You agree that upon such termination,

you will immediately destroy all programs and documentation that relate to the Software, including all copies made or

obtained by you, and otherwise cease use of the Software. If the Software has been installed on a personal computer

or mobile device, you must uninstall the Software immediately. If the Software is software or firmware embedded

on a Product, you must stop using the Product. All provisions of this Agreement except for Section and the limited

warranty in Section 2 (the first paragraph) will survive termination.

. IMPORTANT NOTICE REGARDING YOUR CONSUMER RIGHTS. SOME COUNTRIES, STATES AND/OR PROVINCES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF CERTAIN CONDITIONS, WARRANTIES OR GUARANTEES,

AND/OR DO NOT ALLOW PRODUCTS OR SERVICES TO BE SOLD WITH NO WARRANTIES OR GUARANTEES.

• the serial number on the product has been altered, defaced, or removed; or

• the product was supplied or licensed for beta, evaluation, testing or demonstration purposes, and you didn’t buy or

license the product.

Note: Although this warranty doesn’t apply in these situations, you may have additional rights under consumer laws.

How will Belkin make things right?

If you make an eligible claim under this warranty, Belkin will, at its election:

• repair the product with new or refurbished parts, or pay the reasonable costs of repairing the product;

• replace the product with a reasonably available equivalent new or refurbished Belkin, Linksys or WeMo product; or

• refund you the purchase price of the product, minus any rebates and discounts.

Any repaired or replacement products are warranted for the remainder of the original Warranty Period or 30 days,

whichever is longer. All products and parts that are replaced become the property of Belkin.

Note: The rights and remedies outlined above are the only rights and remedies available under this warranty. However, you

may have additional rights under consumer laws.

GENERAL EXCLUSIONS AND LIMITATIONS OF LIABILITY

IN THOSE JURISDICTIONS WHERE IT CAN LAWFULLY DO SO, AND TO THE MAXIMUM EXTENT PERMITTED BY

APPLICABLE LAW, BELKIN, ITS RESELLERS AND ITS SUPPLIERS HEREBY DISCLAIM AND EXCLUDE ALL OTHER

WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF

MERCHANTABILITY, ACCEPTABILITY, SATISFACTORY QUALITY, NON-INFRINGEMENT, TITLE, FITNESS FOR A

PARTICULAR PURPOSE, LOSS OF OR DAMAGE TO DATA, LACK OF VIRUSES OR FREE FROM VIRUS OR MALWARE

ATTACK, SECURITY, PERFORMANCE, LACK OF NEGLIGENCE, WORKMANLIKE EFFORT, QUIET ENJOYMENT, THAT

THE FUNCTIONS CONTAINED IN THE PRODUCT WILL MEET YOUR REQUIREMENTS, OR THAT DEFECTS IN THE

PRODUCT WILL BE CORRECTED, OR THAT YOUR USE OF THE PRODUCT WILL GENERATE ACCURATE, RELIABLE,

TIMELY RESULTS, INFORMATION, MATERIAL OR DATA. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY

BELKIN, A DEALER, AGENT OR AFFILIATE SHALL CREATE A WARRANTY. TO THE EXTENT WARRANTIES CANNOT

BE DISCLAIMED OR EXCLUDED, THEY ARE LIMITED TO THE DURATION OF THE RELEVANT EXPRESS WARRANTY

PERIOD.

EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO

EVENT SHALL BELKIN, ITS AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS OR THEIR RESPECTIVE

OFFICERS, DIRECTORS, EMPLOYEES, LICENSORS AND ASSIGNS BE LIABLE FOR ANY DIRECT, INDIRECT,

EXEMPLARY, PUNITIVE, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT

NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS OR REVENUE, FOR BUSINESS INTERRUPTION, FOR PERSONAL

INJURY, FOR LOSS OF PRIVACY, FOR LOSS OF ABILITY TO USE ANY THIRD PARTY PRODUCTS OR SERVICES,

FOR FAILURE TO MEET ANY DUTY INCLUDING OF GOOD FAITH OR OF REASONABLE CARE, FOR NEGLIGENCE,

AND FOR ANY OTHER PECUNIARY OR OTHER LOSS WHATSOEVER), REGARDLESS OF THE THEORY OF LIABLITY

(CONTRACT, TORT OR OTHERWISE) ARISING OUT OF OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE

THE PRODUCT, EVEN IF BELKIN OR SUCH OTHER ENTITIES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES. IN NO EVENT SHALL THE TOTAL AGGREGATE LIABILITY OF BELKIN, ITS AFFILIATES, ASSOCIATES,

DEALERS, AGENTS OR SUPPLIERS TO YOU FOR ALL DAMAGES EXCEED THE PRICE YOU PAID FOR THE PRODUCT.

THIS LIMITATION IS CUMULATIVE AND WILL NOT BE INCREASED BY THE EXISTENCE OF MORE THAN ONE

INCIDENT OR CLAIM. THE FOREGOING LIMITATIONS WILL APPLY EVEN IF ANY WARRANTY OR REMEDY PROVIDED

FAILS OF ITS ESSENTIAL PURPOSE. NOTHING IN THIS SECTION SHALL LIMIT THE LIABILITY OF BELKIN IN RELATION

TO DEATH OR BODILY INJURIES.

THE WARRANTIES AND REMEDIES SET OUT IN THIS AGREEMENT ARE EXCLUSIVE, AND, TO THE EXTENT

PERMITTED BY LAW, IN LIEU OF ALL OTHERS ORAL OR WRITTEN, EXPRESS OR IMPLIED. SOME JURISDICTIONS

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES OR OF LIABILITY FOR INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE FOREGOING LIMITATIONS MAY NOT APPLY TO YOU.

If any term is held to be illegal or unenforceable, the legality or enforceability of the remaining terms shall not be affected

or impaired.

BELKIN TECHNICAL AND WARRANTY SUPPORT INFORMATION

HOW DO I GET HELP?

If you have a question about your product or experience a problem with it, please go to http://www.belkin.com/support or

http://support.linksys.com. You will find lots of online support tools and information to help you with your product.

What should I do if my product is defective?

You always have the option to return the product to the original seller if you have a problem. You can make a claim based on

this warranty or any consumer laws that apply to you.

You can also make a claim under this warranty or local consumer laws by contacting Linksys or Belkin Technical Support. To

find out how to contact us, click the “Contact Us” link on the home page of http://Linksys.com or http://www.belkin.com. If

you are located outside the United States, you will need to choose your region/location first:

ACCORDINGLY, IF THESE LAWS APPLY TO YOU, SOME OR ALL OF THE SECTIONS BELOW ENTITLED “LIMITED

WARRANTY AND DISCLAIMER” AND “GENERAL EXCLUSIONS AND LIMITATION OF LIABILITY” MAY NOT APPLY

TO YOU. ONLY THOSE EXCLUSIONS AND LIMITATIONS THAT ARE LAWFUL IN YOUR JURISDICTION WILL APPLY

TO YOU AND, IN SUCH INSTANCES, BELKIN’S LIABILITY WILL BE LIMITED ONLY TO THE MAXIMUM EXTENT

PERMITTED BY LAW. THE ENFORCEABILITY OF THESE LIMITED WARRANTIES MAY VARY BASED ON THE

LOCAL LAWS APPLICABLE TO YOU, AND YOU MAY HAVE ADDITIONAL RIGHTS DEPENDING ON WHERE YOU

LIVE. FOR EXAMPLE, IN AUSTRALIA AND NEW ZEALAND, OUR SOFTWARE AND THE MEDIA ON WHICH IT IS

PROVIDED COME WITH STATUTORY GUARANTEES, INCLUDING AS TO QUALITY AND FITNESS FOR PURPOSE,

WHICH CANNOT BE EXCLUDED OR LIMITED UNDER THE AUSTRALIAN CONSUMER LAW OR THE CONSUMER

GUARANTEES ACT 993 (NEW ZEALAND) (AS FURTHER EXPLAINED BELOW).

THIS AGREEMENT IS NOT INTENDED TO AND DOES NOT: (I) CHANGE OR EXCLUDE ANY STATUTORY CONSUMER

RIGHTS THAT CANNOT BE LAWFULLY CHANGED OR EXCLUDED; OR (II) LIMIT OR EXCLUDE ANY RIGHT YOU

HAVE AGAINST THE PERSON WHO SOLD THE PRODUCT TO YOU IF THAT PERSON HAS BREACHED ANY SALES

CONTRACT WITH YOU. YOU AGREE TO USE THE SOFTWARE IN COMPLIANCE WITH ALL APPLICABLE LAWS,

INCLUDING LOCAL LAWS OF THE COUNTRY OR REGION IN WHICH YOU LIVE OR IN WHICH YOU DOWNLOAD OR USE

THE SOFTWARE.

CERTAIN LEGISLATION, INCLUDING THE AUSTRALIAN CONSUMER LAW AND THE CONSUMER GUARANTEES

ACT 993 (NEW ZEALAND) (“CGA”) MAY IMPLY WARRANTIES OR CONDITIONS, OR IMPOSE GUARANTEES OR

OBLIGATIONS ON BELKIN, WHICH OPERATE TO PROTECT CERTAIN AUSTRALIAN OR NEW ZEALAND PURCHASERS

OF GOODS AND SERVICES IN VARIOUS CIRCUMSTANCES ("AU/NZ APPLICABLE LAWS"). NOTHING IN THIS

AGREEMENT EXCLUDES, RESTRICTS OR MODIFIES ANY CONDITION, WARRANTY, GUARANTEE, RIGHT OR REMEDY

IMPLIED OR IMPOSED BY ANY AU/NZ APPLICABLE LAWS WHICH CANNOT LAWFULLY BE EXCLUDED, RESTRICTED

OR MODIFIED. If any condition, warranty or guarantee is implied into this Agreement or imposed on Belkin under AU/

NZ Applicable Laws and cannot be excluded, but Belkin has a choice of a remedy, then Belkin’s liability for breach of the

condition, warranty or guarantee is limited to one or more of the following, at Belkin’s option: (a) in the case of goods, the

replacement of the goods or the supply of equivalent goods, the repair of the goods or refunding the payment for the goods

if it would be unreasonable to expect the products to be repaired; or (b) in the case of services, the supplying of the services

again, or the payment of the cost of having the services supplied again. In addition to these remedies a "consumer" (within

the meaning of the CGA) may claim for any reasonably foreseeable loss (other than loss or damage through reduction of

value of the goods) that results from the initial problem.

2. LIMITED WARRANTY AND DISCLAIMER. Belkin warrants that any media (such as a CD or USB stick) on which the

Software is provided will be free from defects in materials and workmanship under normal use for 90 days from the

date of its original purchase (the “Warranty Period”). If you make an eligible software media claim under this warranty

during the Warranty Period (the “Limited Warranty”), Belkin will honor this warranty by replacing the Software media.

To make a claim under this Limited Warranty, return the defective media along with the sales receipt directly to Belkin

at the following address: Belkin International, Inc., 2045 E. Waterfront Drive, Playa Vista, CA 90094. This Limited

Warranty is void if failure of the media has resulted from accident, abuse, or misapplication. Any replacement media

will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. In relation to

consumers who are entitled to the benefit of the CGA, the media on which Software is provided comes with guarantees

that cannot be excluded under New Zealand law, and this Limited Warranty is in addition to any statutory rights

such consumers may have under New Zealand law. This Limited Warranty does not apply in Australia. Consumers

in Australia have statutory rights in relation to the Software and media on which the Software is provided under the

Australian Consumer Law.

EXCEPT FOR THIS LIMITED WARRANTY ON MEDIA, SUBJECT TO SECTION AND TO THE MAXIMUM EXTENT

PERMITTED BY APPLICABLE LAW, THE SOFTWARE AND ANY RELATED PROGRAMS AND DOCUMENTATION IS

PROVIDED TO YOU “AS IS,” WITH ALL FAULTS AND WITHOUT WARRANTIES OF ANY KIND. IN THOSE JURISDICTIONS

WHERE IT CAN LAWFULLY DO SO, AND TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, BELKIN,

ITS RESELLERS AND ITS SUPPLIERS HEREBY DISCLAIM AND EXCLUDE ALL OTHER WARRANTIES, EXPRESS,

STATUTORY OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY,

ACCEPTABLE OR SATISFACTORY QUALITY, NON-INFRINGEMENT, TITLE, FITNESS FOR A PARTICULAR PURPOSE,

LOSS OF OR DAMAGE TO DATA, LACK OF VIRUSES OR FREE FROM VIRUS OR MALWARE ATTACK, SECURITY,

PERFORMANCE, LACK OF NEGLIGENCE, WORKMANLIKE EFFORT, QUIET ENJOYMENT, THAT THE FUNCTIONS

CONTAINED IN THE SOFTWARE WILL MEET YOUR REQUIREMENTS, OR THAT YOUR USE OF OR THE PERFORMANCE

OF THE SOFTWARE AND RELATED INFORMATION, PROGRAMS AND DOCUMENTATION WILL BE UNINTERRUPTED

OR ERROR-FREE, OR THAT DEFECTS IN THE SOFTWARE WILL BE CORRECTED, OR THAT YOUR USE OF THE

SOFTWARE AND RELATED INFORMATION, PROGRAMS AND DOCUMENTATION WILL GENERATE ACCURATE,

RELIABLE, TIMELY RESULTS, INFORMATION, MATERIAL OR DATA. NO ORAL OR WRITTEN INFORMATION OR ADVICE

GIVEN BY BELKIN, A DEALER, AGENT OR AFFILIATE SHALL CREATE A WARRANTY. To the extent warranties cannot be

disclaimed or excluded, they are limited to the duration of the relevant Warranty Period.

YOUR USE OF THE SOFTWARE, PRODUCT AND RELATED PROGRAMS AND DOCUMENTATION IS AT YOUR OWN RISK

AND DISCRETION. YOU ARE SOLELY RESPONSIBLE FOR (AND BELKIN DISCLAIMS) ANY AND ALL LOSS, LIABILITY,

OR DAMAGES, INCLUDING TO YOUR HOME, HVAC SYSTEM, ELECTRICAL SYSTEM, PLUMBING, PRODUCT, OTHER

PERIPHERALS CONNECTED TO THE PRODUCT, COMPUTER, MOBILE DEVICE, AND ALL OTHER ITEMS AND PETS

IN YOUR HOME, RESULTING FROM YOUR MISUSE OF THE SOFTWARE, PRODUCT AND RELATED PROGRAMS AND

DOCUMENTATION. YOU ARE RESPONSIBLE FOR COMPLYING WITH ANY SAFETY WARNINGS AND PRECAUTIONS

THAT ACCOMPANY THE PRODUCT. IF YOU ARE NOT COMFORTABLE WITH USING THE PRODUCT AFTER READING

THE SAFETY WARNINGS, YOU MUST RETURN THE PRODUCT TO YOUR PLACE OF PURCHASE AND STOP USING THE

For Linksys.com:

http://www.linksys.com/us/change-region/

For Belkin.com:

http://www.belkin.com/us/ - Click the “Change Region” link at the bottom of the website and select your location

If I believe my product is defective and covered by this warranty, what do I need to do?

You will need to contact Technical Support for your region at the links above. So that we can help you, you will need to give

us some information when you contact us:

• your product model, hardware revision and serial number;

• the name of your Internet Service Provider (ISP); and

• proof that you purchased the product, with the date of the purchase shown and place where it was purchased. WE

WILL ALWAYS NEED A DATED PROOF OF ORIGINAL PURCHASE TO PROCESS WARRANTY CLAIMS.

Sometimes we will need you to send the product back to us so that we can fix or replace it. If we ask you to return your

product to us by post, you will be given a Return Materials Authorization (RMA) number and we’ll tell you where to send the

product. You will need to make sure the product is properly packaged and shipped, and you will be responsible for the

costs of returning your product to us. We need to identify your product when it reaches us, so you’ll need to include the RMA

number AND a copy of your dated proof of original purchase (please keep the original) with the returned product. We also

recommend that you send the package by registered and insured mail or by overnight courier to protect the package while

it is in transit.

What happens when I return my product?

Defective products covered by this warranty will be replaced without charge with the same product or an equivalent product

of equal or greater value, or Belkin will provide you with a refund of the purchase price of the product, minus any rebates and

discounts. The remedy offered will be determined by Belkin in its sole discretion.

We can only ship replacement or repaired products to locations in the country where the original product was purchased.

Belkin may need to delete all or part of your data to repair or replace your product. Belkin may also install software

updates as part of warranty service. PLEASE MAKE SURE THAT YOU BACK UP ALL OF YOUR DATA ON THE PRODUCT

BEFORE SENDING IT IN FOR REPAIR OR REPLACEMENT. BELKIN IS NOT RESPONSIBLE FOR ANY LOSS OF DATA OR

SOFTWARE DURING WARRANTY SERVICE.

Replacements not covered under warranty or your rights under consumer law may be refused by place of purchase, or may

be subject to charge.

Technical support

This warranty is not a service or support contract. Details on our technical support offerings and policies (including any

applicable fees) can be found at http://www.belkin.com/support or http://support.linksys.com.

Belkin provides many different options to support you. Please click on or go to the appropriate website below for more

details. Please make sure to change to your local country if necessary.

• Belkin and WeMo Products: http://www.belkin.com/support

• Linksys Products: http://support.linksys.com

Along with the Limited Warranty, Belkin provides Complimentary Assisted Technical Support for the Warranty Period to get

your hardware up and running. Complimentary Assisted Technical Support includes technical support (by phone) and live

chat (through your computer). At this time, live chat is only available in certain countries. Please visit our websites (indicated

above) in your local area for details.

For additional support beyond the Complimentary Assisted Technical Support period or for assistance on advanced features

beyond basic support, please contact our Technical Support team to learn more about how we can help you get the most

out of your product. Please note that you may be assessed a fee to speak with our technician if you contact us outside the

Complimentary Assisted Technical Support period.

Additional information on some of our Premium Support Offerings can be found at:

Linksys Networking Products –Cable Modem RID.DOCX

http://www.linksys.com/us/premium-support/

Belkin and WeMo Networking Products – http://www.belkin.com/us/belkin-premium-support/

Please Note: Some of these offerings may not be offered in your country

Telephone support may not be available where you live and may be subject to charge.

GPL (General Public License)

Licenses and notices for third party software used in this product may be viewed on http://support.linksys.com/en-us/license.

Please contact http://support.linksys.com/en-us/gplcodecenter for questions or GPL source code requests

SOFTWARE. BELKIN IS NOT RESPONSIBLE FOR (I) YOUR FAILURE TO FOLLOW SAFETY WARNINGS, PRECAUTIONS

OR ANY OTHER INSTRUCTIONS PROVIDED WITH THE PRODUCT AND/OR SOFTWARE, (II) YOUR NEGLIGENCE IN USE

OF THE PRODUCT AND/OR SOFTWARE, OR (III) YOUR INTENTIONAL MISUSE OF THE PRODUCT OR SOFTWARE.

YOU FURTHER ACKNOWLEDGE THAT THE SOFTWARE AND ANY RELATED PROGRAMS AND DOCUMENTATION

ARE NOT CERTIFIED FOR EMERGENCY RESPONSE OR INTENDED OR SUITABLE FOR USE IN SITUATIONS OR

ENVIRONMENTS WHERE FAILURE, DELAY OR ERRORS OR INACCURACIES IN THE DATA OR INFORMATION

PROVIDED BY THE SOFTWARE COULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE PHYSICAL OR

ENVIRONMENTAL DAMAGE, INCLUDING WITHOUT LIMITATION IN CONNECTION WITH THE OPERATION OF

NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OR COMMUNICATION SYSTEMS, AIR TRAFFIC CONTROL, LIFE

SUPPORT OR WEAPONS SYSTEMS. YOU UNDERSTAND THAT THE PRODUCTS AND SOFTWARE ARE NOT PART

OF AND DO NOT CONTAIN A THIRD-PARTY MONITORED EMERGENCY NOTIFICATION SYSTEM. BELKIN DOES

NOT MONITOR EMERGENCY NOTIFICATIONS AND WILL NOT DISPATCH EMERGENCY AUTHORITIES TO YOUR

HOME IN THE EVENT OF AN EMERGENCY. BELKIN CUSTOMER SUPPORT CONTACTS CANNOT BE CONSIDERED A

LIFESAVING SOLUTION AND THEY ARE NOT A SUBSTITUTE FOR EMERGENCY SERVICES. ALL LIFE THREATENING

AND EMERGENCY SITUATIONS SHOULD BE DIRECTED TO THE APPROPRIATE EMERGENCY RESPONSE SERVICES

IN YOUR AREA.

It is your responsibility to back up your system, including without limitation, any material, information or data that you may

use or possess in connection with the Product or Software, and Belkin shall have no liability for your failure to back up your

system or any material, information or data.

Some Belkin Products and Software may monitor energy consumption in the home. Belkin does not guarantee or promise

any specific level of energy savings or other monetary benefit from the use of the Products or Software or any other

feature. Actual energy savings and any associated monetary benefits vary based on factors beyond Belkin’s control or

knowledge. From time to time, Belkin may use the Software to provide you with information that is unique to you and

your energy usage and suggests an opportunity to save money on energy bills if you adopt suggestions or features of the

Product or Software. You acknowledge that this information is not a guarantee of actual savings, and you agree not to seek

monetary or other remedies from Belkin if your savings differs. All information provided to you by Belkin is provided “as is”

and “as available”. We cannot guarantee that it is correct or up to date. In cases where it is critical, accessing information

through the Software is not a substitute for direct access of the information in the home.

3. GENERAL EXCLUSIONS AND LIMITATION OF LIABILITY: SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION

OR LIMITATION OF IMPLIED WARRANTIES OR OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES,

SO THE FOREGOING LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS AGREEMENT GIVES YOU

SPECIFIC LEGAL RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION. TO THE MAXIMUM EXTENT

PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL BELKIN, ITS AFFILIATES, ASSOCIATES, DEALERS,

AGENTS OR SUPPLIERS OR THEIR RESPECTIVE OFFICERS, DIRECTORS, EMPLOYEES, LICENSORS AND

ASSIGNS BE LIABLE FOR ANY INDIRECT, EXEMPLARY, PUNITIVE, SPECIAL, INCIDENTAL OR CONSEQUENTIAL

DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS OR REVENUE,

FOR BUSINESS INTERRUPTION, FOR PERSONAL INJURY, FOR LOSS OF PRIVACY, FOR LOSS OF ABILITY TO

USE ANY THIRD PARTY PRODUCTS OR SERVICES, FOR FAILURE TO MEET ANY DUTY INCLUDING OF GOOD

FAITH OR OF REASONABLE CARE, FOR NEGLIGENCE, AND FOR ANY OTHER PECUNIARY OR OTHER LOSS

WHATSOEVER), REGARDLESS OF THE THEORY OF LIABLITY (CONTRACT, TORT OR OTHERWISE) ARISING OUT

OF OR IN ANY WAY RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF BELKIN OR SUCH

OTHER ENTITIES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE

TOTAL AGGREGATE LIABILITY OF BELKIN, ITS AFFILIATES, ASSOCIATES, DEALERS, AGENTS OR SUPPLIERS

TO YOU FOR ALL DAMAGES EXCEED THE LESSER OF FIFTY DOLLARS ($50.00) OR THE PRICE YOU PAID FOR

THE PRODUCT, THE SOFTWARE OR THE MEDIA CONTAINING THE SOFTWARE. THIS LIMITATION IS CUMULATIVE

AND WILL NOT BE INCREASED BY THE EXISTENCE OF MORE THAN ONE INCIDENT OR CLAIM. THE FOREGOING

LIMITATIONS WILL APPLY EVEN IF ANY WARRANTY OR REMEDY PROVIDED FAILS OF ITS ESSENTIAL PURPOSE.

NOTHING IN THIS SECTION IS INTENDED TO LIMIT THE LIABILITY, UNDER APPLICABLE LAW, OF BELKIN IN

RELATION TO DEATH OR BODILY INJURIES.

IF YOU LIVE IN THE EUROPEAN UNION, REFERENCES TO "SPECIAL, INDIRECT, CONSEQUENTIAL, PUNITIVE

OR INCIDENTAL DAMAGES" SHALL MEAN ANY LOSSES WHICH (I) WERE NOT REASONABLY FORESEEABLE BY

BOTH PARTIES; (II) WERE KNOWN TO YOU BUT NOT TO US; AND/OR (III) WERE REASONABLY FORESEEABLE

BY BOTH PARTIES BUT COULD HAVE BEEN PREVENTED BY YOU SUCH AS, FOR EXAMPLE (BUT WITHOUT

LIMITATION), LOSSES CAUSED BY VIRUSES, MALWARE OR OTHER MALICIOUS PROGRAMS, OR LOSS OF OR

DAMAGE TO YOUR DATA.

The warranties and remedies set out in this Agreement are exclusive, and, to the extent permitted by law, in lieu of all

others oral or written, express or implied.

4. EXPORT CONTROL LAWS: You agree that the use of the Software is subject to U.S. and local export control laws and

regulations. You represent and warrant that you are not a citizen of an embargoed or “terrorist supporting” country or

a prohibited or restricted end user under applicable U.S. or local export and anti-terrorism laws, regulations and lists.

You agree to strictly comply with all export control laws and regulations and agree not to export, re-export, divert,

transfer or disclose any portion of the Software or any related technical information or materials, directly or indirectly,

in violation of any applicable export law or regulation.

5. U.S. GOVERNMENT USERS: The Software and user documentation qualify as “commercial items” as defined at 48

C.F.R. 2.0 and 48 C.F.R. 2.2 2. All U.S. Government users acquire the Software and user documentation with only

Details and Disclosures

CG7500

AC1900, 24 x 8

CABLE MODEM ROUTER

those rights herein that apply to non-governmental customers. Use of either the Software or user documentation

or both constitutes agreement by the U.S. Government that the Software and user documentation are “commercial

computer software” and “commercial computer software documentation,” and constitutes acceptance of the rights and

restrictions herein.

6. GENERAL TERMS. If any portion of this Agreement or any of its terms is found to be void or unenforceable by law in

a particular jurisdiction, such portion or terms shall be interpreted and enforced to the maximum extent allowed in

such jurisdiction, and the remaining provisions or any part thereof will remain in full force and effect. This Agreement

constitutes the entire agreement between Belkin and you with respect to the Software and your use thereof and

supersedes any conflicting or additional terms contained in any purchase order or elsewhere. No provision of this

Agreement may be waived, modified or superseded except by a written instrument accepted by Belkin and you.

However, the Belkin Privacy Policy referenced herein is subject to change in the manner described in that document.

Belkin may provide translations of this Agreement as a convenience to users. However, in the event of a conflict or

inconsistency between the English and any non-English versions, the English version of this Agreement shall govern,

to the extent not prohibited by local law in your jurisdiction. Any suppliers of Belkin shall be direct and intended

third-party beneficiaries of this Agreement, including without limitation with respect to the disclaimers of warranties

and limitations on liability set forth herein. Other than as set forth in the preceding sentence, a person or entity who

is not a party to this Agreement shall not have any right to enforce any term of this Agreement. No failure or delay in

exercising any right or remedy shall operate as a waiver of any such (or any other) right or remedy. The language of

this Agreement shall not be construed strictly for or against either party, regardless of who drafted such language or

was principally responsible for drafting it. The rights and obligations under this Agreement are not assignable by you,

and any attempted assignment shall be void and without effect. This Agreement shall bind and inure to the benefit

of the parties and their successors and permitted assigns. In the event of any legal proceeding between the parties

arising out of or related to this Agreement, the prevailing party shall be entitled to recover, in addition to any other relief

awarded or granted, its costs and expenses (including reasonable attorneys’ and expert witness’ fees) incurred in any

such proceeding.

If you are located in the United States, Section 7 applies to you:

7. ARBITRATION, WAIVER OF CLASSWIDE ARBITRATION, GOVERNING LAW & VENUE.

(A) GENERALLY. SUBJECT TO CLAUSE 7(D) BELOW, YOU AND BELKIN EACH ACKNOWLEDGE AND AGREE

THAT ANY CLAIM, DISPUTE OR CONTROVERSY BETWEEN YOU AND BELKIN ARISING OUT OF OR RELATING

TO ( ) THIS AGREEMENT, INCLUDING THE VALIDITY OF THIS SECTION, AND (2) YOUR USE OF SOFTWARE

AND/OR PRODUCT(S) UNDER THIS AGREEMENT (COLLECTIVELY, THE “DISPUTE”) SHALL BE RESOLVED

EXCLUSIVELY AND FINALLY BY BINDING ARBITRATION ADMINISTERED BY JAMS, A NATIONALLY

RECOGNIZED ARBITRATION AUTHORITY, PURSUANT TO ITS CODE OF PROCEDURES THEN IN EFFECT FOR

CONSUMER-RELATED DISPUTES. YOU UNDERSTAND THAT WITHOUT THIS PROVISION YOU WOULD HAVE

HAD A RIGHT TO LITIGATE A DISPUTE THROUGH A COURT BEFORE A JURY OR JUDGE, AND THAT YOU HAVE

EXPRESSLY AND KNOWINGLY WAIVED THOSE RIGHTS AND AGREE INSTEAD TO RESOLVE ANY DISPUTES

THROUGH BINDING ARBITRATION IN ACCORDANCE WITH THE PROVISIONS OF THIS SECTION.

(B) ARBITRATION PROCEDURES AND FEES. PRIOR TO SUBMITTING A CLAIM FOR ARBITRATION, EITHER

PARTY SHALL FIRST NOTIFY THE OTHER PARTY TO TRY TO RESOLVE THE DISPUTE. IF THE DISPUTE IS

NOT RESOLVED WITHIN 60 DAYS OF SUCH NOTIFICATION, THEN THE CLAIM WILL BE SUBMITTED FOR

ARBITRATION. THE ARBITRATION OF ANY DISPUTE OR CLAIM SHALL BE CONDUCTED IN ACCORDANCE

WITH THE THEN CURRENT AND APPLICABLE RULES OF JAMS AS MODIFIED BY THIS AGREEMENT. THE

ARBITRATION SHALL OCCUR BEFORE A SINGLE ARBITRATOR, WHO MUST BE A RETIRED JUDGE OR

JUSTICE, IN ONE OF SIX REGIONAL VENUES CONSISTENT WITH THE VENUE PROVISION BELOW. WHETHER

OR NOT YOU PREVAIL IN THE DISPUTE, SO LONG AS YOUR CLAIM IS NOT FOUND TO BE FRIVOLOUS BY THE

ARBITRATOR AS MEASURED BY RULE (b) OF THE FEDERAL RULES OF CIVIL PROCEDURE, YOU SHALL BE

ENTITLED TO BE REIMBURSED FOR YOUR COSTS OF ARBITRATION, WITHIN THE SOLE DISCRETION OF THE

ARBITRATOR. IF THE ARBITRATION AWARD IS EQUAL TO OR GREATER THAN THE AMOUNT YOU DEMANDED

IN YOUR ARBITRATION CLAIM, BELKIN WILL PAY FOR YOUR REASONABLE AND ACTUAL ATTORNEYS’

FEES YOU HAVE INCURRED TO ARBITRATE THE DISPUTE, PLUS A MINIMUM RECOVERY OF $2,500. ANY

DECISION OR AWARD BY THE ARBITRATOR RENDERED IN AN ARBITRATION PROCEEDING SHALL BE FINAL

AND BINDING ON EACH PARTY, AND MAY BE ENTERED AS A JUDGMENT IN ANY COURT OF COMPETENT

JURISDICTION. IF EITHER PARTY BRINGS A DISPUTE IN A COURT OR OTHER NON-ARBITRATION FORUM,

THE ARBITRATOR OR JUDGE MAY AWARD THE OTHER PARTY ITS REASONABLE COSTS AND EXPENSES

(INCLUDING BUT NOT LIMITED TO ATTORNEYS’ FEES) INCURRED IN ENFORCING COMPLIANCE WITH THIS

BINDING ARBITRATION PROVISION, INCLUDING STAYING OR DISMISSING SUCH DISPUTE. ANY ARBITRATION

SHALL BE CONFIDENTIAL, AND NEITHER YOU, NOR BELKIN NOR THE ARBITRATOR MAY DISCLOSE THE

EXISTENCE, CONTENT OR RESULTS OF ANY ARBITRATION, EXCEPT AS MAY BE REQUIRED BY LAW OR

FOR PURPOSES OF ENFORCEMENT OR APPEAL OF THE ARBITRATION AWARD. JUDGMENT ON ANY

ARBITRATION AWARD MAY BE ENTERED IN ANY COURT HAVING PROPER JURISDICTION. IF ANY PORTION

OF THIS ARBITRATION CLAUSE IS DETERMINED BY A COURT TO BE INAPPLICABLE OR INVALID, THEN THE

REMAINDER SHALL STILL BE GIVEN FULL FORCE AND EFFECT.

TO JOIN OR CONSOLIDATE CLAIMS IN ARBITRATION BY OR AGAINST OTHER CONSUMERS OR ARBITRATE

ANY CLAIMS AS A REPRESENTATIVE OR MEMBER OF A CLASS OR IN A PRIVATE ATTORNEY GENERAL

CAPACITY. YOU UNDERSTAND THAT WITHOUT THIS PROVISION YOU MAY HAVE HAD A RIGHT TO ARBITRATE

A DISPUTE ON A CLASSWIDE OR REPRESENTATIVE BASIS, AND THAT YOU HAVE EXPRESSLY AND

KNOWINGLY WAIVED THOSE RIGHTS AND AGREE INSTEAD TO ARBITRATE ONLY YOUR OWN DISPUTE(S) IN

ACCORDANCE WITH THE PROVISIONS OF THIS SECTION. NOTWITHSTANDING THE ABOVE AGREEMENT TO

ARBITRATE DISPUTES, YOU AND BELKIN EACH ACKNOWLEDGE AND AGREE THAT EITHER PARTY MAY, AS

AN ALTERNATIVE TO ARBITRATION, BRING AN INDIVIDUAL ACTION IN SMALL CLAIMS COURT TO RESOLVE A

DISPUTE, SO LONG AS SUCH SMALL CLAIMS COURT DOES NOT PROVIDE FOR OR ALLOW FOR JOINDER OR

CONSOLIDATION OF CLAIMS.

(D) GOVERNING LAW; INJUNCTIVE RELIEF. THIS AGREEMENT IS TO BE CONSTRUED IN ACCORDANCE WITH AND

GOVERNED BY THE LAWS OF THE STATE OF CALIFORNIA WITHOUT GIVING EFFECT TO ANY CONFLICT OF

LAW RULE THAT WOULD CAUSE THE APPLICATION OF THE LAWS OF ANY JURISDICTION TO THE RIGHTS AND

DUTIES OF THE PARTIES. HOWEVER, WITH RESPECT TO SOFTWARE PROVIDED, IF YOU ARE A CONSUMER

AND YOU LIVE IN A COUNTRY WHERE BELKIN MARKETS OR PROMOTES THE SOFTWARE, LOCAL LAW MAY

REQUIRE THAT CERTAIN CONSUMER PROTECTION LAWS OF YOUR COUNTRY OF RESIDENCE APPLY TO

SOME SECTIONS OF THIS AGREEMENT. IN ADDITION, BELKIN MAY SEEK INJUNCTIVE RELIEF IN ANY COURT

HAVING JURISDICTION TO PROTECT ITS INTELLECTUAL PROPERTY RIGHTS. EACH OF THE UNITED NATIONS

CONVENTION ON CONTRACTS FOR THE INTERNATIONAL SALE OF GOODS AND THE UNITED NATIONS

CONVENTION ON THE LIMITATION PERIOD IN THE INTERNATIONAL SALE OF GOODS IS HEREBY EXPRESSLY

EXCLUDED AND WILL NOT APPLY TO THIS AGREEMENT.

(E) VENUE. EXCEPT FOR INDIVIDUAL SMALL CLAIMS ACTIONS WHICH CAN BE BROUGHT IN ANY SMALL

CLAIMS COURT WHERE JURISDICTION AND VENUE ARE PROPER, ANY ARBITRATION, LEGAL SUIT, ACTION

OR PROCEEDING ARISING OUT OF OR RELATING TO THIS AGREEMENT OR ANY DISPUTE SHALL BE

COMMENCED IN ( ) NEW YORK, NEW YORK, (2) ATLANTA, GEORGIA, (3) CHICAGO, ILLINOIS, (4) DALLAS,

TEXAS, (5) SEATTLE, WASHINGTON, OR (6) LOS ANGELES, CALIFORNIA, AND YOU AND BELKIN EACH

IRREVOCABLY SUBMIT TO THE EXCLUSIVE JURISDICTION AND VENUE OF ANY SUCH PROCEEDING.

HOWEVER, FOR A DISPUTE OF $ 0,000 OR LESS, YOU MAY CHOOSE WHETHER THE ARBITRATION IN ANY OF

THE SIX REGIONAL VENUES PROCEEDS IN PERSON, BY TELEPHONE, OR BASED ONLY ON SUBMISSIONS.

If you are located outside of the United States, or if Section 7 does not apply to you or is otherwise unenforceable as

adjudicated by a court of competent jurisdiction, then Section 8 applies to you:

8. GOVERNING LAW. This Agreement will be governed by California law, without reference to its or any other

jurisdiction’s conflict of laws principles. Any action arising out of or relating to this Agreement may be brought

exclusively in the appropriate state or federal court in Los Angeles, California, and Belkin and you irrevocably consent

to the jurisdiction of such courts and venue in Los Angeles, California. However, if you are a consumer and you live in

a country where Belkin markets or distributes the Software, local law may require that certain consumer protection

laws of your country of residence apply to some sections of this Agreement. In addition, Belkin may seek injunctive

relief in any court having jurisdiction to protect its intellectual property rights. Each of the United Nations Convention

on Contracts for the International Sale of Goods and the United Nations Convention on the Limitation Period in the

International Sale of Goods is hereby expressly excluded and will not apply to this Agreement.

BELKIN, LINKSYS, WEMO and many product names and logos are trademarks of the Belkin group of companies. Third-

party trademarks mentioned are the property of their respective owners.

8820-02559 Rev. C00

177.8

[7]

FRONT

BACK

762

[30]

127

[5]

QIG - 110 gsm COATED PAPER

177.8

[7]

FRONT

BACK

762

[30]

127

[5]

QIG - 110 gsm COATED PAPER

LINKSYS CG7500 D3 WiFi Gateway User Manual

LINKSYS LLC D3 WiFi Gateway

User Manual

Navigation menu

Namespaces

Views

Navigation