LINKSYS E1000V21 Wireless-N Broadband Router User Manual Linksys E1000 User Guide

LINKSYS LLC Wireless-N Broadband Router Linksys E1000 User Guide

User Manual

Linksys E1000 Wireless-N RouterUser Guide
Linksys E1000 Table of ContentsiiWireless-N RouterContentsChapter 1: Product Overview 1Top. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Horizontal Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Wall-Mounting Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Chapter 2: Cisco Connect 3Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Main Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Computers and Other Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Guest Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10Router Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10How to Exit Cisco Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12How to Access Cisco Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12Chapter 3: Advanced Configuration 13How to Access the Browser-Based Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Setup > Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Setup > DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17Setup > MAC Address Clone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Setup > Advanced Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19Wireless > Basic Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Manual Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Wireless > Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Wireless > Wireless MAC Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24Wireless > Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25Security > Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Security > VPN Passthrough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26Access Restrictions > Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27Applications and Gaming > Single Port Forwarding. . . . . . . . . . . . . . . . . . . . . . . .28Applications and Gaming > Port Range Forwarding . . . . . . . . . . . . . . . . . . . . . . .29Applications & Gaming > Port Range Triggering . . . . . . . . . . . . . . . . . . . . . . . . . .29Applications and Gaming > DMZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Applications and Gaming > QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Administration > Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33Administration > Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Administration > Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34Administration > Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Administration > Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35Status > Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Status > Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36Status > Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Linksys E1000 Table of ContentsiiiWireless-N RouterAppendix A: Troubleshooting 38Appendix B: Specifications 40
Linksys E1000 Chapter 1: Product Overview1Wireless-N RouterChapter 1: Product OverviewThank you for choosing the Linksys E1000 Wireless-N Router. The Router lets you access the Internet via a wireless connection or through one of its four switched ports. You can also use the Router to share resources such as computers, printers and files. A variety of security features help to protect your data and your privacy while you are online. Security features include Wi-Fi Protected Access 2 (WPA2) security, which encrypts data on your wireless network; a Stateful Packet Inspection (SPI) firewall to help block unauthorized access to your Router; and Network Address Translation (NAT) technology, which enhances network protection by allowing your computers to share Internet access through a single, public Internet IP address. (IP stands for Internet Protocol.)Setup and use of the Router is easy using Cisco Connect, the software that is installed when you run the included CD. Advanced configuration of the Router is available through the provided browser-based utility.Top1, 2, 3, 4 (Blue) These numbered LEDs, corresponding with the numbered ports on the Router’s back panel, serve two purposes. The LED is continuously lit when the Router is connected to a device through that port. It flashes to indicate network activity over that port. Wi-Fi Protected Setup Button If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use the Wi-Fi Protected Setup button to automatically configure wireless security for your wireless network.To use Wi-Fi Protected Setup, refer to “Wi-Fi Protected Setup” on page 21.Wireless (Blue) The Wireless LED lights up when the wireless feature is enabled. It flashes when the Router sends or receives data over the wireless network.Internet (Blue) The Internet LED lights up when there is a connection made through the Internet port. It flashes to indicate network activity over the Internet port. Power (Blue) The Power LED lights up when the Router is powered on. When the Router goes through its self-diagnostic mode during every boot-up, the LED flashes. When the diagnostic is complete, the LED is continuously lit.BackInternet Ethernet4 3 2 1 Reset Power12VDCInternet Using an Ethernet cable (also called a network or Internet cable), the Internet port connects the Router to your Internet connection, which is typically a cable or Digital Subscriber Line (DSL) modem. 4, 3, 2, 1 Using Ethernet cables, these Ethernet ports (4, 3, 2, 1) connect the Router to computers and other Ethernet network devices on your wired network. Reset There are two ways to reset the Router to its factory defaults. Either press and hold the Reset button for approximately five seconds, or restore the defaults from the Administration > Factory  Defaults screen in the Router’s browser-based utility (refer to “Administration > Factory Defaults” on page 35).Power The Power port connects to the included power adapter.Horizontal PlacementThe Router has four rubber feet on its bottom panel. Place the Router on a level surface near an electrical outlet.
Linksys E1000 Chapter 1: Product Overview2Wireless-N RouterWall-Mounting PlacementThe Router has two wall-mount slots on its bottom panel. The distance between the slots is 152 mm. Two screws are needed to mount the Router.Suggested Mounting Hardware2.5-3.0 mm4-5 mm 1-1.5 mmNOTE: Cisco is not responsible for damages incurred by unsecured wall-mounting hardware.Follow these instructions:1. Determine where you want to mount the Router. Make sure that the wall you use is smooth, flat, dry, and sturdy. Also make sure the location is within reach of an electrical outlet.2. Drill two holes into the wall. Make sure the holes are 152 mm apart.3. Insert a screw into each hole and leave 3 mm of its head exposed.4. Position the Router so the wall-mount slots line up with the two screws.5. Place the wall-mount slots over the screws and slide the Router down until the screws fit snugly into the wall-mount slots.152 mmWall-Mounting TemplatePrint this page at 100% size. Cut along the dotted line, and place on the wall to drill precise spacing.
Linksys E1000 Chapter 2: Cisco Connect3Wireless-N RouterChapter 2: Cisco ConnectDuring installation, the setup software installs Cisco Connect on your computer. Cisco Connect offers options to connect additional computers or devices to the Router and allows you to change the Router’s settings.InstallationTo install the Router:1. Insert the CD into your CD-ROM drive.Insert CD2. Click Set up your Linksys Router.DVD/CD-RW Drive (E:) LinksysRouter SetupAutoPlayAlways do this for software and games:Install or run programGeneral optionsSet up your Linksys RouterPublished by Cisco Consumer Products LLCSet AutoPlay defaults in Control PanelOpen folder to view filesusing Windows ExplorerSpeed up my systemusing Windows ReadyBoostDVD/CD-RW Drive (E:) LinksysRouter SetupAlways do this for software and games:Install or run programGeneral optionsSet up your Linksys RouterPublished by Cisco Consumer Products LLCSet AutoPlay defaults in Control PanelOpen folder to view filesusing Windows ExplorerSpeed up my systemusing Windows ReadyBoostSet Up Your Linksys RouterIf you do not see this, access setup on the CD directly. To do so, perform the following steps for your specific operating system:Windows 7a. Go to Start > Computer.b. Double-click your CD-ROM drive.Windows Vistaa. Go to Start > Computer.b. Double-click your CD-ROM drive.Windows XPa. Go to Start > My Computer and select your CD-ROM drive.b. Double-click Setup.exe.Mac OS Xa. Double-click the CD on your desktop.b. Double-click Setup.3. Read the Software End User License Agreement. To accept the agreement and continue with the installation, click Next.License Agreement4. The connection steps are displayed.Connection Overviewa. Plug the power cord into the Power port on the back of the Router.Internet Ethernet4 3 2 1 Reset Power12VDCConnect to Power Port
Linksys E1000 Chapter 2: Cisco Connect4Wireless-N Routerb. Plug the power adapter into an electrical outlet.Connect to Electrical Outletc. Plug one end of an Ethernet cable into the yellow port labeled Internet on the back of the Router. The other end of the Ethernet cable should plug in to your broadband modem or existing gateway/router. Click Next.Internet Ethernet4 3 2 1 Reset Power12VDCConnect Ethernet CableNOTE: You can view detailed connection steps by clicking in the setup software.5. Please wait while the setup software is setting up the Router.Please Wait6. The installation is complete. Click OK.Installation is CompleteNOTE: If you have any problems during the installation process, refer to the Frequently Asked Questions in the setup software, or use a computer with an active Internet connection to visit www.linksys.com/support.Main MenuWhen Cisco Connect starts up, the main menu appears:Main MenuStatus information is displayed in the upper right corner: •online secureYour local network is secure, and your Internet connection is available. •offline secureYour local network is secure; however, your Internet connection is not available. To repair your Internet connection, follow the on-screen instructions.NOTE: A group of computers or other devices connected to a router is a local network. The router allows the networked devices to communicate with each other.
Linksys E1000 Chapter 2: Cisco Connect5Wireless-N RouterThe main menu offers four options: Computers and devices, Parental controls, Guest access, and Router settings.NOTE: To view the FAQs for more information, click Need help?Local Access versus Guest AccessYou can connect computers or devices to your Router by giving them local access (Computers and  devices option) or guest access (Guest access option). Computers and devices with local access will have access to the Internet and to other devices on your local network, including shared computers and printers that are connected to the Router. Local access can be given to a wired or wireless device. Refer to “Computers and Other Devices” on page 6 for more information.Guest access allows you to provide guests visiting your home with Internet access. Your guests will not have access to your other computers or personal data. Provide your guest with the guest network name and password. Guest computers must connect to your network using a wireless network connection. Refer to “Main Menu – Guest Access” on page 5 and “Guest Access” on page 10 for more information.The following diagram shows a typical example of how local access and guest access are used in the same home. Guest Access versus Local Access Diagram1212InternetGuest NotebookFamily NotebookPrinterModemRouter Guest Access (Internet Access Only) Local AccessMain Menu – Computers and DevicesUse this option to connect another computer or device to the Router.There is x device(s) connected to your router The number of devices connected to the Router is displayed. Add device To connect another computer or device to the Router, click Add device and go to “Computers and Other Devices” on page 6.Main Menu – Parental ControlsParental controls restrict Internet access for up to five computers. For the computers you select, you can block or limit Internet access to specific times. You can also block specific websites. Parental controls restrictions are being applied to x device(s) The number of devices with parental controls restrictions is displayed. Change To enable parental controls or change settings, click Change and go to “Parental Controls” on page 8.Main Menu – Guest AccessGuest access provides Internet access only; it does not provide access to the local network and its resources. For example, the guest computer cannot print to a printer on the local network or copy files to a computer on the local network.Guest access helps minimize exposure of your local network. To grant Internet access to friends or family, provide the guest network name and password displayed on this screen.Guests can connect to x-guest using the password xyz When a guest wants Internet access in your home, have the guest do the following: 1. Connect to the wireless guest network, which is the name of your wireless network followed by -guest. 2. Open a web browser.3. On the login screen, enter the password of your guest network. Then click Login.Change To disable guest access or change settings, click Change and go to “Guest Access” on page 10.Main Menu – Router SettingsUse this option to personalize the Router’s settings.Router name is x The name of the Router is displayed.Change To change settings, click Change and go to “Router Settings” on page 10.
Linksys E1000 Chapter 2: Cisco Connect6Wireless-N RouterComputers and Other DevicesThe Computers and other devices screen appears.Computers and Other DevicesComputer Click this option to connect another computer in your home. Go to “Computer” on page 6.Wireless printer Click this option to connect a wireless printer. Go to “Wireless Printer” on page 7.Other devices Click this option to connect a device that is not a computer, such as a smartphone or game console. Go to “Connect Manually” on page 7.ComputerYou can use a USB flash drive to create an Easy Setup Key, which holds the wireless settings for the Router. Then you can use the Easy Setup Key to connect additional computers to the Router. Select the appropriate option: •Yes, I have an Easy Setup Key If you already have an Easy Setup Key, select this option. Click Next and go to “Connect with the Easy Setup Key” on page 6. •No, I don’t have an Easy Setup Key — create a new one now If you want to create or update an Easy Setup Key, select this option. Click Next and go to “Create or Update the Easy Setup Key” on page 7. •I want to connect manually using my wireless settings If you want to connect manually (without an Easy Setup Key), select this option. Click Next and go to “Connect Manually” on page 7.Do You Have an Easy Setup Key?Connect with the Easy Setup Key1. Insert the Easy Setup Key into an available USB port on the computer that you want to connect to the Router.Connecting Another Computer2. On that computer, click Connect to your Linksys Router. (If you do not see this, access the Easy Setup Key through Windows Explorer or the Finder, and double-click Connect.)Follow the on-screen instructions to connect that computer to the Router.3. Come back to this computer. On the Connecting another computer screen, click Next.4. Enter a name that will be used to identify the newly added computer. Then click Finish.Name Your Device
Linksys E1000 Chapter 2: Cisco Connect7Wireless-N RouterCreate or Update the Easy Setup KeyIf you do not have an Easy Setup Key, then you can create one using a USB flash drive. If you already have an Easy Setup Key, then you can update it with the Router’s current settings.1. Insert the Easy Setup Key or a USB flash drive into an available USB port on your computer.Update or Create an Easy Setup Key2. Please wait while settings are copied to the Easy Setup Key.Copying Files to the Easy Setup Key3. Remove the Easy Setup Key. You can now use it to connect other computers to the Router (for more information, refer to “Connect with the Easy Setup Key” on page 6). Click Close.Easy Setup Key Has Been UpdatedConnect Manually1. Enter the Network name (SSID), Security Key, and Security Type settings on your wireless device (SSID stands for Service Set Identifier). To print this information, click Print these settings.Connecting a Device2. After your device connects, click Next.3. Enter a name that will be used to identify this device. Then click Finish.Name Your DeviceWireless Printer1. Refer to your printer’s documentation to learn how to connect it to a wireless printer.2. Enter the  Network  name  (SSID), Security  Key, and Security Type settings on your wireless printer. To print this information, click Print these settings.Connecting a Wireless Printer
Linksys E1000 Chapter 2: Cisco Connect8Wireless-N Router3. Wait until your printer connects. On the Connecting a wireless printer screen, click Next.4. Enter a name that will be used to identify this printer. Then click Finish.Name Your PrinterParental ControlsThe Parental controls screen appears.Parental Controls PasswordFirst-Time Access of Parental Controls1. The first time you access parental controls, you will be asked to set up a parental controls password. Complete the following: •Parental controls password This password protects access to parental controls. Create a password of 4-32 characters. •Verify password Re-enter the password. •Secret question Create a secret question and answer pair. If you forget the password, you can reset it by correctly answering the secret question. Enter your question. •Answer Enter the answer to your secret question.Click OK to save your settings.2. Select the computer whose parental controls you want to set up. Then click OK.Set Up Parental Controls For3. The Parental controls main screen appears.Parental ControlsYou have the following options:Restrict Internet access on The list of computer(s) you have selected for parental controls is displayed. To add, remove, or rename computers on this list, refer to “Restrict Internet Access List” on page 9. To set up parental controls on a computer, refer to “Set Up Parental Controls” on page 9.Change parental controls password Click this option to change the password that protects access to parental controls. Refer to “Change Parental Controls Password” on page 10.
Linksys E1000 Chapter 2: Cisco Connect9Wireless-N RouterRestrict Internet Access ListParental ControlsAdd If you want to apply parental controls to additional computers, click Add.If you clicked Add, the Set up parental controls for screen appears.Set Up Parental Controls ForSelect the computer whose parental controls you want to set up. Then click OK.Remove If there is a computer that should not have parental controls applied, select the computer and click Remove.Rename To give a computer a new name, select the computer and click Rename.If you clicked Rename, the Rename  the  device screen appears.Rename the DeviceEnter the new name. Then click Rename.Set Up Parental ControlsTo set up parental controls for a computer, follow these instructions:1. Select the computer from the Restrict Internet access on list. (If the computer is not listed, click Add to select the computer.)Parental Controls2. The Block Internet access option offers the following: •Always To always block Internet access, select this option. •Specific times To block Internet access during specific days and times, select this option and set the schedule: – School nights Select the appropriate start and end times. – Weekends Select the appropriate start and end times •Never To always allow Internet access, keep the default, Never.3. For the Block specific sites option, click Edit to create a list of websites you want to block. By default, the list is empty.If you clicked Edit, the Block these sites screen appears. Block These Sitesa. On each line, enter a website address that you want to block. For example, to block http://www.example.com, enter example.com on a line.
Linksys E1000 Chapter 2: Cisco Connect10Wireless-N Routerb. Click Save to save your settings.4. On the Parental  controls  screen, click Finish to save your settings.NOTE: Repeat steps 1-4 to set up parental controls for different computers.Change Parental Controls PasswordIf you clicked Change parental controls password, the Change your parental controls password screen appears.Change Your Parental Controls Password •Old password Enter the old password. •New password Enter a new password of 4-32 characters. •Verify password Re-enter the new password.Click Change to save your setting.Guest AccessThe Guest access settings screen appears.Guest Access SettingsAllow guest access By default, guest access is enabled. To disable guest access, select no.Guest network name By default, the setup software sets up the name of the guest network.Password By default, the setup software sets up the password for the guest network. To change the password, click Change.If you clicked Change, the Change guest password screen appears.Change Guest Password •Enter a new guest password Enter a password of 4-32 characters. •Click Change to save your setting.Total guests allowed By default, 5 guests are allowed Internet access through the guest network. Select the appropriate number of guests allowed on your guest network; you can select up to 10 guests.Click Finish to save your settings.Router SettingsThe Router settings screen appears.Router SettingsPersonalizeRouter name The name of the Router is displayed (this is also the name of your wireless network). To change the name, click Change and go to “Change Router Name or Password” on page 11.Password The password that protects access to the Router’s settings is displayed (this also protects wireless access to your local network). To change the password, click Change and go to “Change Router Name or Password” on page 11.
Linksys E1000 Chapter 2: Cisco Connect11Wireless-N RouterEasy Setup KeyUpdate or create key The Easy Setup Key is a USB flash drive that holds the wireless settings for the Router. If you want to create or update an Easy Setup Key, click this option and go to “Create or Update the Easy Setup Key” on page 7. Other OptionsRegister now to receive special offers and updates To sign up to receive special offers and updates, click this option.Router details To view more information about the Router, click this option and go to “Router Details” on page 11.Advanced settings To access settings for advanced users, click this option and go to “Advanced Settings” on page 12.Click Finish to save your settings.Change Router Name or PasswordNOTE: When you change the Router name or password, the name or password of your wireless network also changes, and the Router is reset. ALL computers and devices connected to your Router will momentarily lose their Internet connection. Wired computers and devices will reconnect automatically; however, you will need to reconnect all wireless computers and devices using the wireless network’s new name or password (for more information, refer to “Computers and Other Devices” on page 6).If you clicked Change, the Changing  router  name  or password screen appears.1. To change the Router name or password, click Yes. Otherwise, click No.Changing Router Name or Password2. Complete the following: •Router name Enter a name of 1-32 characters. •Password Enter a password of 8-63 characters. •Click Change to save your settings.Change Router Name and PasswordRouter DetailsThe Router  details screen appears, displaying the Model name, Model number, Serial number, Firmware version, Operating system, Software version, Connection type (WAN), IP address (LAN), IP address (WAN), and Computer IP address. (WAN stands for Wide Area Network, such as the Internet. IP stands for Internet Protocol. LAN stands for Local Area Network.)Copy To copy the details to a text file, click Copy and follow these instructions:1. Open a text editor, such as Microsoft Word or Notepad.2. Go to Edit > Paste.3. Go to File > Save.Router DetailsClick Close to return to the Router settings screen.
Linksys E1000 Chapter 2: Cisco Connect12Wireless-N RouterAdvanced SettingsIf you are an advanced user familiar with router administration, you can access the browser-based utility to use the advanced configuration settings of the Router.Username Enter this username to access the browser-based utility.Password Enter this password to access the browser-based utility.Copy password To copy the password to the Clipboard, click this option.Advanced SettingsClick OK to open the web browser and access the browser-based utility. For more information, refer to “How to Access the Browser-Based Utility” on page 13.How to Exit Cisco ConnectTo exit Cisco Connect, click Close on the main menu.Main MenuHow to Access Cisco ConnectWindowsTo access Cisco Connect, go to Start > All Programs > Cisco Connect.MacTo access Cisco Connect, go to Go > Applications > Cisco Connect.
13Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationChapter 3: Advanced ConfigurationAfter setting up the Router with the setup software (located on the CD-ROM), the Router will be ready for use. If you would like to change its advanced settings, use the Router’s browser-based utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a computer connected to the Router.The browser-based utility has these main tabs: Setup, Wireless, Security, Access  Restrictions, Applications  & Gaming, Administration, and Status. Additional tabs will be available after you click one of the main tabs.How to Access the Browser-Based UtilityTo access the browser-based utility, launch the web browser on your computer, and enter the Router’s default Internet Protocol (IP) address, 192.168.1.1, in the Address field. Then press Enter.NOTE: You can also access the browser-based utility on Windows computers by entering the device name in the Address field. Refer to Device Name under “Router IP” on page 16.A login screen will appear. (Non-Windows 7 users will see a similar screen.) Leave the User  name field blank. Then enter the password you set up during the setup software. (If you did not run the setup software, then use the default password, admin. You can set a new password on the  Administration  >  Management screen. Refer to “Administration > Management” on page 33.) Click OK to continue.Login ScreenNOTE: You can also access the browser-based utility through Cisco Connect. For more information, refer to “Router Settings” on page 10.Setup > Basic SetupThe first screen that appears is the Basic Setup screen. This allows you to change the Router’s general settings. Setup > Basic SetupLanguageLanguage To use a different language, select one from the drop-down menu. The language of the browser-based utility will change five seconds after you select another language.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Internet SetupThe Internet Setup section configures the Router to your Internet connection. Most of this information can be obtained through your Internet Service Provider (ISP).Internet Connection TypeSelect the type of Internet connection your ISP provides from the drop-down menu. The available types are: •Automatic Configuration - DHCP •Static IP •PPPoE •PPTP •L2TP •Telstra Cable
14Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationAutomatic Configuration - DHCPThe default Internet Connection Type is set to Automatic Configuration - DHCP (Dynamic Host Configuration Protocol). Keep the default only if your ISP supports DHCP or if you connect using a dynamic IP address. (This option usually applies to cable connections.)Internet Connection Type > Automatic Configuration - DHCPStatic IPIf you are required to use a permanent IP address to connect to the Internet, select Static IP.Internet Connection Type > Static IPInternet IP Address This is the Router’s IP address, when seen from the Internet. Your ISP will provide you with the IP address you need to enter here.Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.Default Gateway Your ISP will provide you with the Gateway address, which is the ISP server’s IP address.DNS 1-3 Your ISP will provide you with at least one DNS (Domain Name System) server IP address.PPPoESome DSL-based ISPs use Point-to-Point Protocol over Ethernet (PPPoE) to establish Internet connections. If you are connected to the Internet through a DSL line, check with your ISP to see if they use PPPoE. If they do, you will have to enable PPPoE.Internet Connection Type > PPPoEUsername and Password Enter the Username and Password provided by your ISP.Service Name (optional) If provided by your ISP, enter the Service Name.Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to elapse before your Internet connection terminates. The default is 5 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, specify how often the Router should check the Internet connection. The default is 30 seconds.PPTPPoint-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in Europe only.Internet Connection Type > PPTPIf your ISP supports DHCP or you are connecting through a dynamic IP address, then select Obtain an IP Address Automatically. If you are required to use a permanent IP address to connect to the Internet, then select Specify an IP Address. Then configure the following:Specify an IP Address This is the Router’s IP address, as seen from the Internet. Your ISP will provide you with the IP address you need to specify here.Subnet Mask This is the Router’s Subnet Mask, as seen by users on the Internet (including your ISP). Your ISP will provide you with the Subnet Mask.Default Gateway Your ISP will provide you with the Gateway address, which is the ISP server’s IP address.
15Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationDNS 1-3 Your ISP will provide you with at least one DNS (Domain Name System) Server IP address.PPTP Server IP Address Your ISP will provide you with the IP address of the PPTP server.Username and Password Enter the Username and Password provided by your ISP.Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to elapse before your Internet connection terminates. The default is 5 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, specify how often the Router should check the Internet connection. The default is 30 seconds.L2TPLayer 2 Tunneling Protocol (L2TP) is a service that applies to connections in Israel only.Internet Connection Type > L2TPServer IP Address This is the IP address of the L2TP Server. Your ISP will provide you with the IP address you need to specify here.Username and Password Enter the Username and Password provided by your ISP.Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to elapse before your Internet connection terminates. The default is 5 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, specify how often the Router should check the Internet connection. The default is 30 seconds.Telstra CableTelstra Cable is a service that applies to connections in Australia only.Internet Connection Type > Telstra CableServer IP Address This is the IP address of the Telstra Cable. Your ISP will provide you with the IP address you need to specify here.Username and Password Enter the Username and Password provided by your ISP.Connect on Demand: Max Idle Time You can configure the Router to cut the Internet connection after it has been inactive for a specified period of time (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. To use this option, select Connect on Demand. In the Max Idle Time field, enter the number of minutes you want to elapse before your Internet connection terminates. The default is 5 minutes.Keep Alive: Redial Period If you select this option, the Router will periodically check your Internet connection. If you are disconnected, then the Router will automatically re-establish your connection. To use this option, select Keep Alive. In the Redial Period field, specify how often the Router should check the Internet connection. The default is 30 seconds.
16Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationOptional SettingsSome of these settings may be required by your ISP. Verify with your ISP before making any changes.Optional SettingsHost Name and Domain Name These fields allow you to supply a host and domain name for the Router. Some ISPs, usually cable ISPs, require these names as identification. You may have to check with your ISP to see if your broadband Internet service has been configured with a host and domain name. In most cases, leaving these fields blank will work. MTU MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. Select Manual if you want to manually enter the largest packet size that is transmitted. To have the Router select the best MTU for your Internet connection, keep the default setting, Auto.Size When Manual is selected in the MTU field, this option is enabled. Leave this value in the 1200 to 1500 range. The default size depends on the Internet Connection Type: •DHCP, Static IP, or Telstra: 1500 •PPPoE: 1492 •PPTP or L2TP: 1460Network SetupThe Network Setup section configures the IP settings for your local network.Router IPIP Address The Router’s IP address, as seen by your network, is displayed. The default Router IP address is 192.168.1.1.Subnet Mask The Router’s Subnet Mask, as seen by your network, is displayed.Device name To access the browser-based utility, enter the Router’s Device name or IP address. The default is Ciscoxxxxx (xxxxx are the last five digits of the Router’s serial number, found on the product label on the left side of the Router’s bottom panel). If you want to change the default, enter a new Device name. (The Device name is also the Router’s NetBIOS name.)Router IPDHCP Server SettingsThe settings allow you to configure the Router’s DHCP server function. The Router can be used as a DHCP server for your network. A DHCP server automatically assigns an IP address to each computer or device on your network. NOTE: If you choose to enable the DHCP server option, make sure there is no other DHCP server on your network. DHCP Server SettingsDHCP Server DHCP is enabled by factory default. If you already have a DHCP server on your network, or you do not want a DHCP server, then select Disabled (no other DHCP features will be available).DHCP Reservation Click DHCP Reservation if you want to assign a fixed local IP address to a specific device on your network. This is helpful if you have a device you need to access at the same address all the time, such as a media server or print server. You can reserve the IP address for the specific device by selecting it from the list of devices or by manually entering the MAC address of the device. DHCP ReservationYou will see a list of DHCP clients with the following information: Client Name, Interface, IP Address, and MAC Address. DHCP Reservation
17Wireless-N RouterLinksys E1000 Chapter 3: Advanced Configuration •Select Clients from DHCP Table Click the Select check box to reserve a client’s IP address. Then click Add Clients. •Manually Adding Client To manually assign an IP address, enter the client’s name in the Enter  Client Name field. Enter the IP address you want it to have in the Assign IP Address field. Enter its MAC address in the To This MAC Address field. Then click Add.Clients Already ReservedA list of DHCP clients and their fixed local IP addresses is displayed at the bottom of the screen. If you want to remove a client from this list, click Remove.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes. To update the on-screen information, click Refresh. To exit this screen, click Close.Start IP Address The Start IP Address specifies the starting IP address for the range of addresses assigned by your Router when it functions as a DHCP server. (The first IP address assigned by the Router will be randomly selected within the range you specify.)Because the Router’s default IP address is 192.168.1.1, the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.254. The default Start IP Address is 192.168.1.100.Maximum Number of Users Enter the maximum number of computers that you want the DHCP server to assign IP addresses to. This number cannot be greater than 253. The default is 50.IP Address Range The range of available IP addresses is displayed.Client Lease Time The Client Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP address. Enter the amount of time, in minutes, that the user will be “leased” this dynamic IP address. After the time is up, the user will be automatically assigned a new dynamic IP address, or the lease will be renewed. The default is 0 minutes, which means one day.Static DNS 1-3 The Domain Name System (DNS) is how the Internet translates domain or website names into Internet addresses or Uniform Resource Locators (URLs). Your ISP will provide you with at least one DNS Server IP address. If you wish to use another, enter that IP address in one of these fields. You can enter up to three DNS Server IP addresses here. The Router will use these for quicker access to functioning DNS servers.WINS The Windows Internet Naming Service (WINS) manages each computer’s interaction with the Internet. If you use a WINS server, enter that server’s IP address here. Otherwise, leave this blank.Time SettingsTime SettingTime Zone Select the time zone in which your network functions from this drop-down menu.Automatically adjust clock for daylight saving changes Select this option to have the Router automatically adjust for daylight saving time.RebootRebootReboot Click Reboot to restart the Router.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Setup > DDNSThe Router offers a Dynamic Domain Name System (DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic Internet IP address. It is useful when you are hosting your own website, File Transfer Protocol (FTP) server, or other server behind the Router. Before you can use this option, you need to sign up for DDNS service with a DDNS service provider, www.dyndns.org or www.tzo.com. If you do not want to use this option, keep the default, Disabled.DDNSDDNS ServiceIf your DDNS service is provided by DynDNS.org, then select DynDNS.org from the drop-down menu. If your DDNS service is provided by TZO, then select TZO.com. The options available on the DDNS screen will vary, depending on which DDNS service provider you use.
18Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationDynDNS.orgSetup > DDNS > DynDNSUsername Enter the Username for your DDNS account.Password Enter the Password for your DDNS account.Host Name The DDNS URL assigned by the DDNS service is displayed.System Select the DynDNS service you use: Dynamic, Static, or Custom. The default selection is Dynamic.Mail Exchange (Optional) Enter the address of your mail exchange server, so emails to your DynDNS address go to your mail server.Backup MX This option allows the Mail eXchange (MX) server to be a backup. To disable this option, keep the default, Disabled. To enable the option, select Enabled. If you are not sure which setting to select, keep the default, Disabled.Wildcard This setting enables or disables wildcards for your host. For example, if your DDNS address is myplace.dyndns.org and you enable wildcards, then x.myplace.dyndns.org will work as well (x is the wildcard). To disable wildcards, keep the default, Disabled. To enable wildcards, select Enabled. If you are not sure which setting to select, keep the default, Disabled.Internet IP Address The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.Status The status of the DDNS service connection is displayed.Update To manually trigger an update, click Update.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.TZO.comSetup > DDNS > TZOE-mail Address, TZO Key, and Domain Name Enter the settings of the account you set up with TZO.Internet IP Address The Router’s Internet IP address is displayed here. Because it is dynamic, it will change.Status The status of the DDNS service connection is displayed.Update To manually trigger an update, click Update.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Setup > MAC Address CloneA Media Access Control (MAC) address is a 12-digit code assigned to a unique piece of hardware for identification. Some ISPs require you to register a MAC address in order to access the Internet. If you have your computer’s MAC address registered with your ISP and you do not wish to re-register the MAC address, then you may assign the registered MAC address to the Router with the MAC Address Clone feature.Setup > MAC Address CloneMAC Address CloneEnabled/Disabled To have the MAC address cloned, select Enabled.MAC Address Enter the MAC address registered with your ISP here.
19Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationClone My PC’s MAC Click this option to clone the MAC address of the computer you are using.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Setup > Advanced RoutingThis screen is used to set up the Router’s advanced functions. Operating Mode allows you to select the type(s) of advanced functions you use. Dynamic Routing automatically adjusts how packets travel on your network. Static Routing sets up a fixed route to another network destination.Setup > Advanced RoutingAdvanced RoutingNATEnabled/Disabled If this Router is hosting your network’s connection to the Internet, keep the default, Enabled. If another router exists on your network, select Disabled. When the NAT setting is disabled, dynamic routing will be available.Dynamic Routing (RIP)Dynamic routing uses the Routing Information Protocol (RIP). This option enables the Router to automatically adjust to physical changes in the network’s layout and exchange routing tables with the other router(s). The Router determines the network packets’ route based on the fewest number of hops between the source and the destination. Enabled/Disabled When the NAT setting is enabled, the Dynamic Routing option is automatically disabled. When the NAT setting is disabled, this option is available. Select Enabled to use the Dynamic Routing option.Static RoutingA static route is a pre-determined pathway that network information must travel to reach a specific host or network. Enter the information described below to set up a new static route.Route Entries To set up a static route between the Router and another network, select a number from the drop-down list. Click Delete This Entry to delete a static route.Enter Route Name Enter a name for the Route here, using a maximum of 25 alphanumeric characters.Destination LAN IP The Destination LAN (Local Area Network) IP is the address of the remote network or host to which you want to assign a static route.Subnet Mask The Subnet Mask determines which portion of a Destination LAN IP address is the network portion, and which portion is the host portion. Gateway This is the IP address of the gateway device that allows for contact between the Router and the remote network or host.Interface This interface tells you whether the Destination IP address is on the LAN & Wireless (Ethernet and wireless networks) or the Internet (WAN). (WAN stands for Wide Area Network.)Click Show Routing Table to view the static routes you have already set up.Advanced Routing > Routing TableRouting TableFor each route, the Destination LAN IP address, Subnet Mask, Gateway, and Interface are displayed. Click Refresh to update the information. Click Close to exit this screen.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
20Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationWireless > Basic Wireless SettingsThe basic settings for wireless networking are set on this screen.There are two ways to configure the Router’s wireless network(s), manual and Wi-Fi Protected Setup.Wi-Fi Protected Setup is a feature that makes it easy to set up your wireless network. If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup, then you can use Wi-Fi Protected Setup.Configuration View To manually configure your wireless networks, select Manual. Proceed to the Manual Setup section. To use Wi-Fi Protected Setup, select Wi-Fi Protected Setup. Proceed to “Wi-Fi Protected Setup” on page 21.Manual SetupIf you set the Configuration  View  to Manual, the Basic Wireless Settings screen displays the following fields.Wireless > Basic Wireless Settings (Manual Setup)Network Mode From this drop-down menu, you can select the wireless standards running on your network. •Mixed If you have Wireless-N, Wireless-G, and Wireless-B devices in your network, keep the default, Mixed. •BG-Mixed If you have only Wireless-G and Wireless-B devices in your network, select BG-Mixed. •Wireless-N Only If you have only Wireless-N devices, select Wireless-N Only. •Wireless-G Only If you have only Wireless-G devices, select Wireless-G Only. •Wireless-B Only If you have only Wireless-B devices, select Wireless-B Only. •Disabled If you do not have any wireless devices in your network, select Disabled.NOTE: If you are not sure which mode to use, keep the default, Mixed.Network Name (SSID) The Service Set Identifier (SSID) is the network name shared by all devices in a wireless network. It is case-sensitive and must not exceed 32 keyboard characters. The default is Ciscoxxxxx (xxxxx are the last five digits of the Router’s serial number, found on the product label on the left side of the Router’s bottom panel). The setup software that you use to install your Router and set up your wireless network changes the default Network Name to an easy-to-remember name.NOTE: If you restore the Router’s factory default settings (by pressing the Reset button or using the Administration  >  Factory  Defaults screen), the Network Name will return to its default value, and all devices on your wireless network will need to be reconnected.Channel Width The default is 20 MHz Only. For best performance, select Auto (20 MHz or 40 MHz) to have the Router automatically select the Channel Width, 20 MHz or 40 MHz.Channel Select the appropriate channel for your wireless network. If you are not sure which channel to select, then keep the default, Auto.SSID Broadcast When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router’s SSID, keep the default, Enabled. If you do not want to broadcast the Router’s SSID, then select Disabled.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
21Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationWi-Fi Protected SetupThere are three methods available. Use the method that applies to the client device you are configuring.Wireless > Basic Wireless Settings (Wi-Fi Protected Setup)NOTE: Wi-Fi Protected Setup configures one client device at a time. Repeat the instructions for each client device that supports Wi-Fi Protected Setup. •Wi-Fi Protected Setup Button Use this method if your client device has a Wi-Fi Protected Setup button.a. Click or press the Wi-Fi Protected Setup button on the client device.b. Click the Wi-Fi Protected Setup button on the Router’s Wi-Fi Protected Setup screen.The Wi-Fi Protected Setup LED flashes blue for two minutes during the Wi-Fi Protected Setup process and lights up blue when the Wi-Fi Protected Setup process is successful.The LED lights up amber if there is an error during the Wi-Fi Protected Setup process. Make sure the client device supports Wi-Fi Protected Setup. Wait until the LED is off, and then try again. The LED flashes when a Wi-Fi Protected Setup session is active. The Router supports one session at a time. Wait until the LED is continuously lit, or off before starting the next Wi-Fi Protected Setup session.c. After the client device has been configured, click OK on the Router’s Wi-Fi  Protected  Setup screen. Then refer back to your client device or its documentation for further instructions. •Enter Client Device PIN on Router Use this method if your client device has a Wi-Fi Protected Setup PIN (Personal Identification Number).a. Enter the PIN from the client device in the field on the Router’s Wi-Fi Protected Setup screen.b. Click the Register button on the Router’s Wi-Fi Protected Setup screen.c. After the client device has been configured, click OK on the Router’s Wi-Fi  Protected  Setup screen. Then refer back to your client device or its documentation for further instructions. •Enter Router PIN on Client Device Use this method if your client device asks for the Router’s PIN. a. On the client device, enter the PIN listed on the Router’s Wi-Fi  Protected  Setup screen. (It is also listed on the label on the bottom of the Router.)b. After the client device has been configured, click OK on the Router’s Wi-Fi  Protected  Setup screen. Then refer back to your client device or its documentation for further instructions.The Network Name (SSID), Security, and Passphrase are displayed at the bottom of the screen.NOTE: If you have client devices that do not support Wi-Fi Protected Setup, note the wireless settings, and then manually configure those client devices.
22Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationWireless > Wireless SecurityThe wireless security settings configure the security of your wireless network. The Router supports the following wireless security options: WPA2/WPA mixed mode, WPA2 Personal, WPA Personal, WEP, and RADIUS. (WPA stands for Wi-Fi Protected Access. WEP stands for Wireless Equivalent Privacy. RADIUS stands for Remote Authentication Dial-In User Service.)Personal OptionsSecurity Option StrengthWPA2 Personal StrongestWPA2/WPA mixed mode WPA2: Strongest WPA: StrongWPA Personal StrongWEP BasicOffice OptionRADIUS is the security option offered for networks that use a RADIUS server for authentication.Security ModeSelect the security method for your wireless network. If you do not want to use wireless security, select Disabled.WPA2/WPA Mixed ModeNOTE: If you select WPA2/WPA Mixed Mode as your Security Mode, each device in your wireless network MUST use the same passphrase.Wireless Security > WPA2/WPA Mixed ModePassphrase Enter a passphrase of 8-63 characters. The default is password.WPA2 PersonalNOTE: If you select WPA2 Personal as your Security Mode, each device in your wireless network MUST use WPA2 Personal and the same passphrase.Wireless Security > WPA2 PersonalPassphrase Enter a passphrase of 8-63 characters. The default is password.WPA PersonalNOTE: If you select WPA Personal as your Security Mode, each device in your wireless network MUST use WPA Personal and the same passphrase.Wireless Security > WPA PersonalPassphrase Enter a passphrase of 8-63 characters. The default is password.
23Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationWEPWEP is a basic encryption method, which is not as secure as WPA. NOTE: If you select WEP as your Security Mode, each device in your wireless network MUST use WEP and the same encryption and shared key.Wireless Security > WEPEncryption Select a level of WEP encryption, 40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).Passphrase Enter a Passphrase to automatically generate WEP keys. Then click Generate.Key 1 If you did not enter a Passphrase, enter the WEP key manually.RADIUSThis option features WEP used in coordination with a RADIUS server. (This should only be used when a RADIUS server is connected to the Router.) NOTE: If you select RADIUS as your Security Mode, each device in your wireless network MUST use RADIUS and the same encryption and shared key.RADIUSRADIUS Server Enter the IP address of the RADIUS server.RADIUS Port Enter the port number of the RADIUS server. The default is 1812.Shared Secret Enter the key shared between the Router and the server.Encryption Select a level of WEP encryption, 40/64 bits (10 hex digits) or 104/128 bits (26 hex digits). The default is 40/64 bits (10 hex digits).Passphrase Enter a Passphrase to automatically generate WEP keys. Then click Generate.Key 2 If you did not enter a Passphrase, enter the WEP key manually.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
24Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationWireless > Wireless MAC FilterWireless access can be filtered (restricted) by specifying the MAC addresses of the devices in your wireless network.Wireless > Wireless MAC FilterWireless MAC FilterEnabled/Disabled To filter wireless users by the MAC addresses of their computers or devices, select Enabled. Otherwise, keep the default, Disabled.Access RestrictionPrevent PCs listed below from accessing the wireless network When the Wireless Mac Filter is enabled and this option is selected, computers listed in the MAC Address filter list will be prevented from accessing the wireless network. This option is enabled by default.Permit PCs listed below access to the wireless network When the Wireless Mac Filter is enabled and this option is selected, only computers listed in the MAC Address filter list will be granted access to the wireless network. This option is disabled by default.MAC Address Filter ListWireless Client List Click this option to open the Wireless Client List screen. Wireless Client ListWireless Client ListThis screen shows computers and other devices on the wireless network. The list can be sorted by Client Name, Interface, IP Address, MAC Address, and Status. Select Save to MAC Address Filter List for any device you want to add to the MAC Address Filter List. Then click Add. To update the on-screen information, click Refresh. To exit this screen and return to the Wireless MAC Filter screen, click Close.MAC 01-50 Enter the MAC addresses of the devices whose wireless access you want to control.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
25Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationWireless > Advanced Wireless SettingsThe Advanced  Wireless  Settings screen is used to set up the Router’s advanced wireless functions. These settings should only be adjusted by an advanced user because incorrect settings can reduce wireless performance. In most cases, keep the default settings.Wireless > Advanced Wireless SettingsAdvanced WirelessAP Isolation The AP (Access Point) Isolation feature isolates all wireless clients and wireless devices on your network from each other. Wireless devices will be able to communicate with the Router but not with each other. To use this option, select Enabled. AP Isolation is disabled by default. Frame Burst This option should provide your network with greater performance, depending on the manufacturer of your wireless products. To use this option, keep the default, Enabled. Otherwise, select Disabled.Authentication Type The Authentication Type setting is available if the Security Mode is RADIUS or WEP. The default is set to Auto, which allows either Open System or Shared Key authentication to be used. With Open System authentication, the sender and the recipient do NOT use a WEP key for authentication. With Shared Key authentication, the sender and recipient use a WEP key for authentication. Select Shared Key to only use Shared Key authentication.Basic Rate The Basic Rate setting is not actually one rate of transmission but a series of rates at which the Router can transmit. (The Basic Rate is not the actual rate of data transmission. If you want to specify the Router’s rate of data transmission, configure the Transmission Rate setting.) The Router will advertise its Basic Rate to the other wireless devices in your network, so they know which rates will be used. The Router will also advertise that it will automatically select the best rate for transmission. The default setting is Default, when the Router can transmit at all standard wireless rates (1-2 Mbps, 5.5 Mbps, 11 Mbps, 18 Mbps, and 24 Mbps). Select 1-2 Mbps for use with older wireless technology. Select All, when the Router can transmit at all wireless rates. Transmission Rate The Transmission setting is available if the Network Mode is BG-Mixed, Wireless-G Only, or Wireless-B Only. The rate of data transmission should be set depending on the speed of your wireless network. Select from a range of transmission speeds, or keep the default, Auto, to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client. N Transmission Rate The N Transmission setting is available if the Network Mode is Mixed or Wireless-N Only. The rate of data transmission should be set depending on the speed of your Wireless-N networking. Select from a range of transmission speeds, or keep the default, Auto, to have the Router automatically use the fastest possible data rate and enable the Auto-Fallback feature. Auto-Fallback will negotiate the best possible connection speed between the Router and a wireless client.CTS Protection Mode The Router automatically uses CTS (Clear-To-Send) Protection Mode when your Wireless-N and Wireless-G devices are experiencing severe problems and are not able to transmit to the Router in an environment with heavy 802.11b traffic. This option boosts the Router’s ability to catch all Wireless-N and Wireless-G transmissions but severely decreases performance. To use this option, keep the default, Auto. To disable this option, select Disabled. Beacon Interval A beacon is a packet broadcast by the Router to synchronize the wireless network. The Beacon Interval value indicates the frequency interval of the beacon. Enter a value between 20 and 65,535 milliseconds. The default value is 100. DTIM Interval This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1.Fragmentation Threshold This value specifies the maximum size for a packet before data is fragmented into multiple packets. If you experience a high packet error rate, you may slightly increase the Fragmentation Threshold. Setting the Fragmentation Threshold too low may result in poor network performance. Only minor reduction of the default value is recommended. In most cases, it should remain at its default value of 2346.
26Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationRTS Threshold Should you encounter inconsistent data flow, only minor reduction of the default value, 2347, is recommended. If a network packet is smaller than the preset Request to Send (RTS) threshold size, the RTS/CTS (Clear to Send) mechanism will not be enabled. The Router sends RTS frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a CTS frame to acknowledge the right to begin transmission. The RTS Threshold value should remain at its default value of 2347Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Security > FirewallThe Firewall screen is used to configure a firewall that can filter out various types of unwanted traffic on the Router’s local network. Security > FirewallFirewallSPI Firewall Protection To use firewall protection, keep the default selection, Enabled. To turn off firewall protection, select Disabled.Internet FiltersFilter Anonymous Internet Requests This option makes it more difficult for outside users to work their way into your network. This option is enabled by default. Disable it to allow anonymous Internet requests.Filter Multicast The multicasting feature allows for multiple transmissions to specific recipients at the same time. If multicasting is permitted, then the Router will allow IP multicast packets to be forwarded to the appropriate computers. Select this option to enable the filter. This option is disabled by default.Filter Internet NAT Redirection This option is used to prevent a local computer from using a URL or Internet address to access the local server. Select this option to enable the filter. This option is disabled by default.Filter IDENT (Port 113) The Filter IDENT (Identification) option keeps port 113 from being scanned by devices outside of your local network. This option is enabled by default. Disable it to allow port 113 to be scanned.Web FiltersProxy Use of WAN proxy servers may compromise the Gateway’s security. Denying Proxy will disable access to any WAN proxy servers. Select this option to enable proxy filtering. Deselect the option to allow proxy access. Java Java is a programming language for websites. If you deny Java, you run the risk of not having access to Internet sites created using this programming language. Select this option to enable Java filtering. Deselect the option to allow Java usage.ActiveX ActiveX is a programming language for websites. If you deny ActiveX, you run the risk of not having access to Internet sites created using this programming language. Select this option to enable ActiveX filtering. Deselect the option to allow ActiveX usage.Cookies A cookie is data stored on your computer and used by Internet sites when you interact with them. Select this option to filter cookies. Deselect the option to allow cookie usage.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Security > VPN PassthroughThe VPN  Passthrough screen allows you to enable Virtual Private Network (VPN) tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.Security > VPN PassthroughVPN PassthroughIPSec Passthrough Internet Protocol Security (IPSec) is a suite of protocols used to implement secure exchange of packets at the IP layer. To allow IPSec tunnels to pass through the Router, keep the default, Enabled. PPTP Passthrough Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default, Enabled. L2TP Passthrough Layer 2 Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the
27Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationInternet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enabled.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Access Restrictions > Internet AccessThe Internet  Access screen allows you to deny or allow specific kinds of Internet usage and traffic, such as Internet access, designated services, and websites during specific days and times.Access Restrictions > Internet AccessInternet Access PolicyAccess Policy Access can be managed by a policy. Use the settings on this screen to establish an access policy (after Save Settings is clicked). Selecting a policy from the drop-down menu will display that policy’s settings. To delete a policy, select that policy’s number and click Delete This Policy. To view all the policies, click Summary. SummaryThe policies are listed with the following information: No., Policy Name, Access, Days, Time, and status (Enabled). To enable a policy, select Enabled. To delete a policy, click Delete. Click Save Settings to save your changes, or click Cancel Changes to clear your changes. To return to the Internet Access Policy screen, click Close. SummaryStatus Policies are disabled by default. To enable a policy, select the policy number from the drop-down menu, and select Enabled.To create a policy, follow steps 1-11. Repeat these steps to create additional policies, one at a time.1. Select a number from the Access  Policy drop-down menu.2. Enter a Policy Name in the field provided. 3. To enable this policy, select Enabled.4. Click Edit List to select which computers will be affected by the policy. The List  of  PCs screen appears. You can select a computer by MAC address or IP address. You can also enter a range of IP addresses if you want this policy to affect a group of computers. After making your changes, click Save Settings to apply your changes, or click Cancel Changes to clear your changes. Then click Close. List of PCs5. Select the appropriate option, Deny or Allow, depending on whether you want to block or allow Internet access for the computers you listed on the List of PCs screen.
28Wireless-N RouterLinksys E1000 Chapter 3: Advanced Configuration6. Decide which days and what times you want this policy to be enforced. Select the individual days during which the policy will be in effect, or select Everyday. Then enter a range of hours and minutes during which the policy will be in effect, or select 24 Hours.7. You can block websites with specific URL addresses. Enter each URL in a separate Website Blocking by URL Address field.8. You can also block websites using specific keywords. Enter each keyword in a separate Website Blocking by Keyword field. 9. You can filter access to various services accessed over the Internet, such as FTP or telnet. (You can block up to three applications per policy.)From the Applications list, select the application you want to block. Then click the >> button to move it to the Blocked List. To remove an application from the Blocked List, select it and click the << button.10. If the application you want to block is not listed or you want to edit a service’s settings, enter the application’s name in the  Application  Name field. Enter its range in the Port  Range fields. Select its protocol from the Protocol drop-down menu. Then click Add.To modify a service, select it from the Applications list. Change its Application Name, Port Range, and/or Protocol setting. Then click Modify.To delete a service, select it from the Applications list. Then click Delete.11. Click Save Settings to save the policy’s settings, or click Cancel Changes to clear the changes.Applications and Gaming > Single Port ForwardingThe Single Port  Forwarding screen allows you to customize port services for various applications.When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate computers (also called servers). Before using forwarding, you should assign static IP addresses to the designated computers (use the DHCP Reservation option on the Basic Setup screen; refer to “DHCP Reservation” on page 16).Applications and Gaming > Single Port ForwardingSingle Port ForwardingPreset applications are available for the first five entries. For each entry, complete the following:Application Name Select the appropriate application. To IP Address Enter the IP address of the computer that should receive the requests. If you assigned a static IP address to the computer, then you can look up its static IP address; refer to “DHCP Reservation” on page 16.Enabled Select Enabled to enable port forwarding.You can customize entries for additional applications. For each entry, complete the following:Application Name Enter the name you wish to give the application. Each name can be up to 12 characters.External Port Enter the external port number used by the computer or Internet application. Check with the Internet application documentation for more information.Internal Port Enter the internal port number used by the computer or Internet application. Check with the Internet application documentation for more information.Protocol Select the protocol(s) used for this application, TCP (Transmission Control Protocol), UDP (User Datagram Protocol),or Both.To IP Address Enter the IP address of the computer that should receive the requests. If you assigned a static IP address to the computer, then you can look up its static IP address; refer to “DHCP Reservation” on page 16.Enabled Select Enabled to enable port forwarding.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
29Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationApplications and Gaming > Port Range ForwardingThe  Port  Range  Forwarding screen allows you to set up public services on your network, such as web servers, FTP servers, email servers, or other specialized Internet applications. (Specialized Internet applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. Some Internet applications may not require any forwarding.)When users send these types of requests to your network via the Internet, the Router will forward those requests to the appropriate computers (also called servers). Before using forwarding, you should assign static IP addresses to the designated computers (use the DHCP Reservation option on the Basic Setup screen; refer to “DHCP Reservation” on page 16).If you need to forward all ports to one computer, click the DMZ tab.Applications and Gaming > Port Range ForwardingPort Range ForwardingFor each entry, complete the following:Application Name Enter the name you wish to give the application. Each name can be up to 12 characters.Start~End Port Enter the number or range of port(s) used by the server or Internet application. Check with the Internet application documentation for more information.Protocol Select the protocol(s) used for this application, TCP, UDP, or Both.To IP Address Enter the IP address of the computer running the specific application. If you assigned a static IP address to the computer, then you can look up its static IP address; refer to “DHCP Reservation” on page 16.Enabled Select Enabled to enable port forwarding.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Applications & Gaming > Port Range TriggeringThe Port  Range  Triggering screen allows the Router to watch outgoing data for specific port numbers. The IP address of the computer that sends the matching data is remembered by the Router, so that when the requested data returns through the Router, the data is pulled back to the proper computer by way of IP address and port mapping rules.Applications and Gaming > Port Range TriggeringPort Range TriggeringFor each entry, complete the following:Application Name Enter the application name of the trigger.Triggered Range Enter the starting and ending port numbers of the triggered port number range. Check with the Internet application documentation for the port number(s) needed.Forwarded Range Enter the starting and ending port numbers of the forwarded port number range. Check with the Internet application documentation for the port number(s) needed.Enabled Select Enabled to enable port triggering.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
30Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationApplications and Gaming > DMZThe DMZ (Demilitarized Zone) feature allows one network computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconferencing. DMZ hosting forwards all the ports at the same time to one computer. The Port Range Forwarding feature is more secure because it only opens the ports you want to have opened, while DMZ hosting opens all the ports of one computer, exposing the computer to the Internet. Applications and Gaming > DMZDMZAny computer whose port is being forwarded should have its DHCP client function disabled and have a new static IP address assigned to it because its IP address may change when using the DHCP function.Enabled/Disabled To disable DMZ hosting, select Disabled. To expose one computer, select Enabled. Then configure the following settings:Source IP Address If you want any IP address to be the source, select Any IP Address. If you want to specify an IP address or range of IP addresses as the designated source, select and complete the IP address range fields.Destination If you want to specify the DMZ host by IP address, select IP Address and enter the IP address in the field provided. If you want to specify the DMZ host by MAC address, select MAC Address and enter the MAC address in the field provided. To retrieve this information, click DHCP Client Table.DMZ > DHCP Client TableDHCP Client TableThe DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by Client Name, Interface, IP Address, and MAC Address. To select a DHCP client, click Select. To update the on-screen information, click Refresh. To exit this screen and return to the DMZ screen, click Close. Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.Applications and Gaming > QoSQuality of Service (QoS) is a method that assigns priority to specific types of network traffic, which often are demanding, real-time applications, such as gaming, videoconferencing, video streaming, and Voice over Internet Protocol (VoIP) telephony. QoS helps to ensure optimal performance for these types of uses.Applications and Gaming > QoS QoS (Quality of Service)WirelessWMM Support Wi-Fi Multimedia (WMM) is a wireless Quality of Service feature that improves quality for audio, video, and voice applications by prioritizing wireless traffic. To use this feature, the wireless client devices in your network must support Wireless WMM. To disable
31Wireless-N RouterLinksys E1000 Chapter 3: Advanced Configurationthis option, select Disabled. Otherwise, keep the default, Enabled.No Acknowledgement If you want to disable the Router’s Acknowledgement option, so the Router will not re-send data if an error occurs, then select Enabled. Otherwise, keep the default, Disabled.Internet Access PriorityIn this section, you can set the bandwidth priority for a variety of applications and devices. There are four levels of priority: High, Medium, Normal, or Low. When you set priority, do not set all applications to High, because this will defeat the purpose of allocating the available bandwidth. If you want to select below normal bandwidth, select Low. Depending on the application, a few attempts may be needed to set the appropriate bandwidth priority.Enabled/Disabled To use the QoS policies you set, select Enabled. Otherwise, keep the default, Disabled.Upstream BandwidthUpstream Bandwidth This option sets the maximum outgoing bandwidth that applications can use. To allow the Router to set the maximum, keep the default, Auto. To specify the maximum, select Manual. Then enter the appropriate value and select Kbps or Mbps.CategoryYou can define the Internet access priority level for as many categories as you want. The Summary section will display all of the priority selections that you enter. Select from the following categories: •Applications Allows you to assign a priority level for a pre-defined application or one that you add. •Online Games Allows you to assign a priority level for a pre-defined game or one that you add. •MAC Address This option lets you prioritize network traffic based on the device that is accessing the network. For example, if you want your gaming console to have higher priority accessing the Internet than your computer, you can assign their priority levels using their respective MAC addresses. •Voice Device Voice devices require a higher priority level. You can assign a higher priority level to voice devices using their respective MAC addresses.SummaryThis lists the QoS entries you have created for your applications and devices. Refer to “Summary” on page 32 for more information.ApplicationsApplications Select the appropriate application. If you select Add a New Application, follow the instructions in the Add a New Application section.Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low.Click Add to save your changes. Your new entry will appear in the Summary list.Add a New ApplicationQoS > Add a New ApplicationEnter a Name Enter a name for this application.Port Range Enter the port range that the application will be using. For example, if you want to allocate bandwidth for FTP, you can enter 21-21. If you need services for an application that uses from 1000 to 1250, you enter 1000-1250 as your settings. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.Select the protocol TCP or UDP, or select Both. Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low.Click Add to save your changes. Your new entry will appear in the Summary list.Online GamesQoS > Online GamesGame Select the appropriate game. If you select Add a New Game, follow the instructions in the Add a New Game section.Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low.Click Add to save your changes. Your new entry will appear in the Summary list.
32Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationAdd a New GameQoS > Add a New GameEnter a Name Enter any name to indicate the name of the entry.Port Range Enter the port range that the game will be using. You can have up to three ranges to define for this bandwidth allocation. Port numbers can range from 1 to 65535. Check your application’s documentation for details on the service ports used.Select the protocol TCP or UDP, or select Both. Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low.Click Add to save your changes. Your new entry will appear in the Summary list.MAC AddressQoS > MAC AddressThe MAC address of the computer you are using is displayed.Enter a Name Enter a name for your device.MAC Address Enter the MAC address of your device.Priority Select the appropriate priority: High, Medium (Recommend), Normal, or Low.Click Add to save your changes. Your new entry will appear in the Summary list.Voice DeviceQoS > Voice DeviceEnter a Name Enter a name for your voice device.MAC Address Enter the MAC address of your voice device.Priority Select the appropriate priority: High (Recommend), Medium, Normal, or Low.Click Add to save your changes. Your new entry will appear in the Summary list.SummaryThis lists the QoS entries you have created for your applications and devices.Priority This column displays the bandwidth priority of High, Medium, Normal, or Low.Name This column displays the application, game, device, or port name.Information This column displays the port range or MAC address entered for your entry. If a pre-configured application or game was selected, there will be no valid entry shown in this section.Remove Click this option to remove an entry.Edit Click this option to make changes.Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
33Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationAdministration > ManagementThe Management screen allows the network’s administrator to manage specific Router functions for access and security.Administration > ManagementManagementTo ensure the Router’s security, you will be asked for your password when you access the Router’s browser-based utility. The default is admin.Router Password Enter a new password for the Router.Re-enter to confirm Enter the password again to confirm.Web AccessWeb Utility Access HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secure Socket Layer) to encrypt data transmitted for higher security. Select HTTP or HTTPS. The default is HTTP.Web Utility Access via Wireless If you are using the Router in a public domain where you are giving wireless access to your guests, you can disable wireless access to the Router’s browser-based utility. You will only be able to access the utility via a wired connection if you disable the setting. Keep the default, Enabled, to allow wireless access to the utility, or select Disabled to block wireless access to the utility.Remote AccessRemote Management To permit remote access of the Router from the Internet (outside the local network), select Enabled. Otherwise, keep the default, Disabled.Web Utility Access HTTP (HyperText Transport Protocol) is the communications protocol used to connect to servers on the World Wide Web. HTTPS uses SSL (Secure Socket Layer) to encrypt data transmitted for higher security. Select HTTP or HTTPS. HTTP is the default.Remote Upgrade If you want to be able to upgrade the Router from the Internet (outside the local network), select Enabled. (You must have the Remote Management option enabled as well.) Otherwise, keep the default, Disabled.Allowed Remote IP Address If you want to be able to access the Router from any external IP address, select Any IP Address. If you want to specify an external IP address or range of IP addresses, then select the second option and complete the fields provided.Remote Management Port Enter the port number that will be open to outside access. (To access the Router, you will need to enter the Router’s password.)NOTE: When you are in a remote location and wish to manage the Router, enter http://xxx.xxx.xxx.xxx:yyyy or https://xxx.xxx.xxx.xxx:yyyy, depending on whether you use HTTP or HTTPS. Enter the Router’s specific Internet IP address in place of xxx.xxx.xxx.xxx, and enter the Remote Management Port number in place of yyyy.UPnPUniversal Plug and Play (UPnP) allows the appropriate Windows operating system to automatically configure the Router for various Internet applications, such as gaming and videoconferencing.UPnP If you want to use UPnP, keep the default, Enabled. Otherwise, select Disabled.Allow Users to Configure Keep the default, Enabled, if you want to be able to make manual changes to the Router while using the UPnP feature. Otherwise, select Disabled.Allow Users to Disable Internet Access Select Enabled, if you want to be able to prohibit any and all Internet connections. Otherwise, keep the default, Disabled.Backup and RestoreBackup Configurations To back up the Router’s configuration settings, click this option and follow the on-screen instructions.Restore Configurations To restore the Router’s configuration settings, click this option and follow the on-screen instructions. (You must have previously backed up the Router’s configuration settings.)Click Save Settings to apply your changes, or click Cancel Changes to clear your changes.
34Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationAdministration > LogThe Router can keep logs of all traffic for your Internet connection.Administration > LogLogLog To disable the Log function, keep the default, Disabled. To monitor traffic between the network and the Internet, select Enabled. With logging enabled, you can choose to view temporary logs.Click Save Settings to apply your change, or click Cancel Changes to clear your change.View Log When you wish to view the logs, click this option. Log > View LogLog •Type Select Incoming Log, Outgoing Log, Security Log, or DHCP Client Log. •<Type> Log The Incoming Log displays a temporary log of the source IP addresses and destination port numbers for the incoming Internet traffic. The Outgoing Log displays a temporary log of the local IP addresses, destination URLs/IP addresses, and service/port numbers for the outgoing Internet traffic. The Security log displays the login information for the browser-based utility. The DHCP Client Log displays the local DHCP server status information.Click Save the Log to save this information to a file on your computer’s hard drive. Click Refresh to update the log. Click Clear to clear all the information that is displayed.Administration > DiagnosticsThe diagnostic tests (Ping and Traceroute) allow you to check the connections of your network devices, including connection to the Internet.Administration > DiagnosticsDiagnosticsPing TestPing checks the status of a connection. IP or URL Address Enter the address of the computer, device, or website whose connection you wish to test.Packet Size Enter the packet size you want to use. The default is 32 bytes.Times to Ping Enter the number of times you wish to test the connection. The default is 5.Start to Ping To run the test, click this option. The Ping screen shows if the test is successful. Click Close to return to the Diagnostics screen. Click Stop to stop the test.Diagnostics > PingTraceroute TestTraceroute checks the performance of a connection.IP or URL Address Enter the address of the computer, device, or website whose connection you wish to test.
35Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationStart to Traceroute To run the test, click this option. The Traceroute screen shows if the test is successful. Click Close to return to the Diagnostics screen. Click Stop to stop the test.Diagnostics > TracerouteAdministration > Factory DefaultsThe Factory  Defaults screen allows you to restore the Router’s configuration to its factory default settings. NOTE: Do not restore the factory defaults unless you are having difficulties with the Router and have exhausted all other troubleshooting measures. Once the Router is reset, you will have to re-enter all of your configuration settings.Administration > Factory DefaultsFactory DefaultsRestore All Settings To reset the Router’s settings to the defaults, click this option and then follow the on-screen instructions. Any settings you have saved will be lost when the default settings are restored.Administration > Firmware UpgradeThe Firmware  Upgrade screen allows you to upgrade the Router’s firmware. Do not upgrade the firmware unless you are experiencing problems with the Router or the new firmware has a feature you want to use. Administration > Firmware UpgradeNOTE: The Router may lose the settings you have customized. Before you upgrade its firmware, write down all of your custom settings. After you upgrade its firmware, you will have to re-enter all of your configuration settings.Firmware UpgradeBefore upgrading the firmware, download the Router’s firmware upgrade file from the website, www.linksys.com/support.Please select a file to upgrade the firmware Click Browse and select the firmware upgrade file.Start to Upgrade After you have selected the appropriate file, click this option, and follow the on-screen instructions. WARNING: Do not interrupt the upgrade process. You should not turn off the power or press the Reset button during the upgrade process. Doing so may disable the Router.
36Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationStatus > RouterThe Router screen displays information about the Router and its current settings.Status > RouterRouter InformationFirmware Version The version number of the Router’s current firmware is displayed.Firmware Verification The unique identifier of the firmware is displayed.Current Time The time set on the Router is displayed.Internet MAC Address The Router’s MAC address, as seen by your ISP, is displayed.Host Name The Host Name of the Router is displayed (if it was entered on the Setup > Basic Setup screen).Domain Name The Domain Name of the Router is displayed (if it was entered on the  Setup  >  Basic  Setup screen).Internet ConnectionThis section shows the current network information stored in the Router. The information varies depending on the Internet connection type selected on the Setup > Basic Setup screen.For a DHCP connection, select Release IP Address or Renew IP Address as appropriate to release or renew a DHCP lease. For a PPPoE or similar connection, select Connect or Disconnect as appropriate to connect to or disconnect from the Internet.Click Refresh to update the on-screen information. Status > Local NetworkThe Local Network screen displays information about the local network. Status > Local NetworkLocal NetworkLocal MAC Address The MAC address of the Router’s local, wired interface is displayed.Router IP Address The Router’s IP address, as it appears on your local network, is displayed.Subnet Mask The Subnet Mask of the Router is displayed.DHCP ServerDHCP Server The status of the Router’s DHCP server function is displayed.Start IP Address For the range of IP addresses that can be used by devices on your local network, the starting IP address is displayed.End IP Address For the range of IP addresses that can be used by devices on your local network, the ending IP address is displayed.
37Wireless-N RouterLinksys E1000 Chapter 3: Advanced ConfigurationDHCP Client Table Click this option to view a list of computers or other devices that are using the Router as a DHCP server.DHCP Client TableDHCP Client TableThe DHCP Client Table lists computers and other devices that have been assigned IP addresses by the Router. The list can be sorted by IP Address, MAC Address, Interface, and Client Name. To remove a DHCP client, click Delete. To update the on-screen information, click Refresh. To exit this screen and return to the Local Network screen, click Close. Status > Wireless NetworkThe Wireless  Network screen displays information about your wireless network.Status > Wireless NetworkWireless NetworkMAC Address The MAC address of the Router’s local, wireless interface is displayed.Mode The wireless mode is displayed.Network Name (SSID) The name of the wireless network, which is also called the SSID, is displayed.Channel Width The Channel Width setting (selected on the Wireless > Basic Wireless Settings screen) is displayed.Channel The Channel setting selected on the Basic Wireless Settings screen is displayed.Security The wireless security method used by the Router is displayed.SSID Broadcast The status of the SSID Broadcast option is displayed.
Linksys E1000 Appendix A: Troubleshooting38Wireless-N RouterAppendix A: TroubleshootingYour computer cannot connect to the Internet. Follow these instructions until your computer can connect to the Internet: •Verify that the power adapter is connected to the Router and to a power outlet. If connected to a power strip, make sure the power strip is turned on. •Make sure that the Power LED, Internet LED, and Wireless LED are on. If you have any wired computers connected to the Router, make sure the appropriate port LED is lit. NOTE: The Power LED flashes after the power adapter is plugged in to the Router. If the light remains flashing for more than 30 seconds, it may indicate the Router is not working properly. For assistance, use a computer or device with Internet access to refer to our Linksys E1000 support section on the web, www.linksys.com/support/E1000 •Make sure that your DSL or cable modem is connected to your Router’s Internet port using an Ethernet cable. •Reset all of the devices on your network:1. Turn off all of your network computers and devices, and then unplug the power adapter from your Router.2. Unplug your modem’s power cord (and coaxial cable if you have a cable modem), and wait two minutes.3. Reconnect your modem’s power cord (and coaxial cable) and wait two more minutes.4. Reconnect the power adapter to the Router, and then power on all of your network computers and devices.The modem does not have an Ethernet port.The modem is a dial-up modem for traditional dial-up service. To use the Router, you need a cable/DSL modem and high-speed Internet connection.You cannot use the DSL service to connect manually to the Internet.After you have installed the Router, it will automatically connect to your Internet Service Provider (ISP), so you no longer need to connect manually.The DSL telephone line does not fit into the Router’s Internet port.The Router does not replace your modem. You still need your DSL modem in order to use the Router. Connect the telephone line to the DSL modem, and then insert the setup CD into your computer. Click Set up your Linksys Router and follow the on-screen instructions.When you double-click the web browser, you are prompted for a username and password. If you want to get rid of the prompt, follow these instructions.Launch the web browser and perform the following steps (these steps are specific to Internet Explorer but are similar for other browsers):1. Select Tools > Internet Options. 2. Click the Connections tab.3. Select Never dial a connection. 4. Click OK.The Router does not have a coaxial port for the cable connection.The Router does not replace your modem. You still need your cable modem in order to use the Router. Connect your cable connection to the cable modem, and then insert the setup CD into your computer. Click Set up your Linksys Router and follow the on-screen instructions.The computer cannot connect wirelessly to the network.Make sure the wireless network name or SSID is the same on both the computer and the Router. If you have enabled wireless security, then make sure the same security method and key are used by both the computer and the Router.You need to modify the settings on the Router.Router settings can be modified using the Cisco Connect software; refer to “How to Access Cisco Connect” on page 12. To modify the advanced settings, go to Advanced settings. Refer to “Advanced Settings” on page 12.You want to access the browser-based utility from Cisco Connect.To enter the browser-based utility from Cisco Connect, follow these steps:1. Open Cisco Connect.2. On the main menu, click Router settings.3. Click Advanced settings. 4. Write down the username and password that are displayed. (To help protect your password, you can copy it to the Clipboard by clicking Copy password.)5. Click OK.
Linksys E1000 Appendix A: Troubleshooting39Wireless-N Router6. Your web browser automatically opens. Enter the username and password, and then click OK. (If you copied the password to the Clipboard in step 4, press Ctrl-V to paste it into the Password field.)When you try to log into the browser-based utility, your password does not work.Your wireless security password also serves as the browser-based utility’s login password. To see this password:1. Open Cisco Connect.2. On the main menu, click Router settings.3. The Password is displayed on the left side of the screen.WEB: If your questions are not addressed here, refer to our E1000 section on the web, www.linksys.com/support/E1000
Linksys E1000 Appendix B: Specifications40Wireless-N RouterAppendix B: SpecificationsModel Name Linksys E1000Description Wireless-N RouterModel Number E1000Standards 802.11n, 802.11g, 802.11b, 802.3, 802.3uPorts Power, Internet, and Ethernet (1-4)Buttons Reset, Wi-Fi Protected SetupLEDs Ethernet (1-4), Wi-Fi Protected Setup, Wireless, Internet, PowerCabling Type CAT 5eRF Pwr (EIRP) in dBm 17.5 dBmAntenna Gain in dBi 1.5 dBiUPnP able/cert AbleSecurity Features WEP, WPA, WPA2Security Key Bits Up to 128-Bit EncryptionEnvironmentalDimensions 7.95" x 1.34" x 6.3" (202 x 34 x 160 mm)Unit Weight 9.81 oz (280 g)Power 12V, 0.5ACertifications FCC, CE, IC-03, Wi-Fi, Windows 7Operating Temp. 32 to 104°F (0 to 40°C)Storage Temp. -4 to 140°F (-20 to 60°C)Operating Humidity 10 to 85% NoncondensingStorage Humidity 5 to 90% NoncondensingSpecifications are subject to change without notice.10041510A-JLFederal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Industry Canada Statement This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
www.linksys.com/support© 2010 Cisco Systems, Inc. All rights reserved. Cisco, the Cisco logo, and Linksys are trademarks or registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

Navigation menu